arch/arm/boot/dts/dra7.dtsi

// SPDX-License-Identifier: GPL-2.0-only
/*
 * Copyright (C) 2013 Texas Instruments Incorporated - https://www.ti.com/
 *
 * Based on "omap4.dtsi"
 */

#include <dt-bindings/bus/ti-sysc.h>
#include <dt-bindings/clock/dra7.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/pinctrl/dra.h>
#include <dt-bindings/clock/dra7.h>

#define MAX_SOURCES 400

/ {
	#address-cells = <2>;
	#size-cells = <2>;

	compatible = "ti,dra7xx";
	interrupt-parent = <&crossbar_mpu>;
	chosen { };

	aliases {
		i2c0 = &i2c1;
		i2c1 = &i2c2;
		i2c2 = &i2c3;
		i2c3 = &i2c4;
		i2c4 = &i2c5;
		serial0 = &uart1;
		serial1 = &uart2;
		serial2 = &uart3;
		serial3 = &uart4;
		serial4 = &uart5;
		serial5 = &uart6;
		serial6 = &uart7;
		serial7 = &uart8;
		serial8 = &uart9;
		serial9 = &uart10;
		ethernet0 = &cpsw_port1;
		ethernet1 = &cpsw_port2;
		d_can0 = &dcan1;
		d_can1 = &dcan2;
		spi0 = &qspi;
	};

	timer {
		compatible = "arm,armv7-timer";
		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
			     <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
			     <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
			     <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>;
		interrupt-parent = <&gic>;
	};

	gic: interrupt-controller@48211000 {
		compatible = "arm,cortex-a15-gic";
		interrupt-controller;
		#interrupt-cells = <3>;
		reg = <0x0 0x48211000 0x0 0x1000>,
		      <0x0 0x48212000 0x0 0x2000>,
		      <0x0 0x48214000 0x0 0x2000>,
		      <0x0 0x48216000 0x0 0x2000>;
		interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_HIGH)>;
		interrupt-parent = <&gic>;
	};

	wakeupgen: interrupt-controller@48281000 {
		compatible = "ti,omap5-wugen-mpu", "ti,omap4-wugen-mpu";
		interrupt-controller;
		#interrupt-cells = <3>;
		reg = <0x0 0x48281000 0x0 0x1000>;
		interrupt-parent = <&gic>;
	};

	cpus {
		#address-cells = <1>;
		#size-cells = <0>;

		cpu0: cpu@0 {
			device_type = "cpu";
			compatible = "arm,cortex-a15";
			reg = <0>;

			operating-points-v2 = <&cpu0_opp_table>;

			clocks = <&dpll_mpu_ck>;
			clock-names = "cpu";

			clock-latency = <300000>; /* From omap-cpufreq driver */

			/* cooling options */
			#cooling-cells = <2>; /* min followed by max */

			vbb-supply = <&abb_mpu>;
		};
	};

	cpu0_opp_table: opp-table {
		compatible = "operating-points-v2-ti-cpu";
		syscon = <&scm_wkup>;

		opp_nom-1000000000 {
			opp-hz = /bits/ 64 <1000000000>;
			opp-microvolt = <1060000 850000 1150000>,
					<1060000 850000 1150000>;
			opp-supported-hw = <0xFF 0x01>;
			opp-suspend;
		};

		opp_od-1176000000 {
			opp-hz = /bits/ 64 <1176000000>;
			opp-microvolt = <1160000 885000 1160000>,
					<1160000 885000 1160000>;

			opp-supported-hw = <0xFF 0x02>;
		};

		opp_high@1500000000 {
			opp-hz = /bits/ 64 <1500000000>;
			opp-microvolt = <1210000 950000 1250000>,
					<1210000 950000 1250000>;
			opp-supported-hw = <0xFF 0x04>;
		};
	};

	/*
	 * The soc node represents the soc top level view. It is used for IPs
	 * that are not memory mapped in the MPU view or for the MPU itself.
	 */
	soc {
		compatible = "ti,omap-infra";
		mpu {
			compatible = "ti,omap5-mpu";
			ti,hwmods = "mpu";
		};
	};

	/*
	 * XXX: Use a flat representation of the SOC interconnect.
	 * The real OMAP interconnect network is quite complex.
	 * Since it will not bring real advantage to represent that in DT for
	 * the moment, just use a fake OCP bus entry to represent the whole bus
	 * hierarchy.
	 */
	ocp: ocp {
		compatible = "simple-bus";
		#address-cells = <1>;
		#size-cells = <1>;
		ranges = <0x0 0x0 0x0 0xc0000000>;
		dma-ranges = <0x80000000 0x0 0x80000000 0x80000000>;
		ti,hwmods = "l3_main_1", "l3_main_2";

		l3-noc@44000000 {
			compatible = "ti,dra7-l3-noc";
			reg = <0x44000000 0x1000>,
			      <0x45000000 0x1000>;
			interrupts-extended = <&crossbar_mpu GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,
					      <&wakeupgen GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
		};

		l4_cfg: interconnect@4a000000 {
		};
		l4_wkup: interconnect@4ae00000 {
		};
		l4_per1: interconnect@48000000 {
		};
		l4_per2: interconnect@48400000 {
		};
		l4_per3: interconnect@48800000 {
		};

		/*
		 * Register access seems to have complex dependencies and also
		 * seems to need an enabled phy. See the TRM chapter for "Table
		 * 26-678. Main Sequence PCIe Controller Global Initialization"
		 * and also dra7xx_pcie_probe().
		 */
		axi0: target-module@51000000 {
			compatible = "ti,sysc-omap4", "ti,sysc";
			power-domains = <&prm_l3init>;
			resets = <&prm_l3init 0>;
			reset-names = "rstctrl";
			clocks = <&pcie_clkctrl DRA7_PCIE_PCIE1_CLKCTRL 0>,
				 <&pcie_clkctrl DRA7_PCIE_PCIE1_CLKCTRL 9>,
				 <&pcie_clkctrl DRA7_PCIE_PCIE1_CLKCTRL 10>;
			clock-names = "fck", "phy-clk", "phy-clk-div";
			#size-cells = <1>;
			#address-cells = <1>;
			ranges = <0x51000000 0x51000000 0x3000>,
				 <0x20000000 0x20000000 0x10000000>;
			dma-ranges;
			/**
			 * To enable PCI endpoint mode, disable the pcie1_rc
			 * node and enable pcie1_ep mode.
			 */
			pcie1_rc: pcie@51000000 {
				reg = <0x51000000 0x2000>,
				      <0x51002000 0x14c>,
				      <0x20001000 0x2000>;
				reg-names = "rc_dbics", "ti_conf", "config";
				interrupts = <0 232 0x4>, <0 233 0x4>;
				#address-cells = <3>;
				#size-cells = <2>;
				device_type = "pci";
				ranges = <0x81000000 0 0x00000000 0x20003000 0 0x00010000>,
					 <0x82000000 0 0x20013000 0x20013000 0 0x0ffed000>;
				bus-range = <0x00 0xff>;
				#interrupt-cells = <1>;
				num-lanes = <1>;
				linux,pci-domain = <0>;
				ti,hwmods = "pcie1";
				phys = <&pcie1_phy>;
				phy-names = "pcie-phy0";
				ti,syscon-lane-sel = <&scm_conf_pcie 0x18>;
				interrupt-map-mask = <0 0 0 7>;
				interrupt-map = <0 0 0 1 &pcie1_intc 1>,
						<0 0 0 2 &pcie1_intc 2>,
						<0 0 0 3 &pcie1_intc 3>,
						<0 0 0 4 &pcie1_intc 4>;
				ti,syscon-unaligned-access = <&scm_conf1 0x14 1>;
				status = "disabled";
				pcie1_intc: interrupt-controller {
					interrupt-controller;
					#address-cells = <0>;
					#interrupt-cells = <1>;
				};
			};

			pcie1_ep: pcie_ep@51000000 {
				reg = <0x51000000 0x28>,
				      <0x51002000 0x14c>,
				      <0x51001000 0x28>,
				      <0x20001000 0x10000000>;
				reg-names = "ep_dbics", "ti_conf", "ep_dbics2", "addr_space";
				interrupts = <0 232 0x4>;
				num-lanes = <1>;
				num-ib-windows = <4>;
				num-ob-windows = <16>;
				ti,hwmods = "pcie1";
				phys = <&pcie1_phy>;
				phy-names = "pcie-phy0";
				ti,syscon-unaligned-access = <&scm_conf1 0x14 1>;
				ti,syscon-lane-sel = <&scm_conf_pcie 0x18>;
				status = "disabled";
			};
		};

		/*
		 * Register access seems to have complex dependencies and also
		 * seems to need an enabled phy. See the TRM chapter for "Table
		 * 26-678. Main Sequence PCIe Controller Global Initialization"
		 * and also dra7xx_pcie_probe().
		 */
		axi1: target-module@51800000 {
			compatible = "ti,sysc-omap4", "ti,sysc";
			clocks = <&pcie_clkctrl DRA7_PCIE_PCIE2_CLKCTRL 0>,
				 <&pcie_clkctrl DRA7_PCIE_PCIE2_CLKCTRL 9>,
				 <&pcie_clkctrl DRA7_PCIE_PCIE2_CLKCTRL 10>;
			clock-names = "fck", "phy-clk", "phy-clk-div";
			power-domains = <&prm_l3init>;
			resets = <&prm_l3init 1>;
			reset-names = "rstctrl";
			#size-cells = <1>;
			#address-cells = <1>;
			ranges = <0x51800000 0x51800000 0x3000>,
				 <0x30000000 0x30000000 0x10000000>;
			dma-ranges;
			status = "disabled";
			pcie2_rc: pcie@51800000 {
				reg = <0x51800000 0x2000>,
				      <0x51802000 0x14c>,
				      <0x30001000 0x2000>;
				reg-names = "rc_dbics", "ti_conf", "config";
				interrupts = <0 355 0x4>, <0 356 0x4>;
				#address-cells = <3>;
				#size-cells = <2>;
				device_type = "pci";
				ranges = <0x81000000 0 0x00000000 0x30003000 0 0x00010000>,
					 <0x82000000 0 0x30013000 0x30013000 0 0x0ffed000>;
				bus-range = <0x00 0xff>;
				#interrupt-cells = <1>;
				num-lanes = <1>;
				linux,pci-domain = <1>;
				ti,hwmods = "pcie2";
				phys = <&pcie2_phy>;
				phy-names = "pcie-phy0";
				interrupt-map-mask = <0 0 0 7>;
				interrupt-map = <0 0 0 1 &pcie2_intc 1>,
						<0 0 0 2 &pcie2_intc 2>,
						<0 0 0 3 &pcie2_intc 3>,
						<0 0 0 4 &pcie2_intc 4>;
				ti,syscon-unaligned-access = <&scm_conf1 0x14 2>;
				pcie2_intc: interrupt-controller {
					interrupt-controller;
					#address-cells = <0>;
					#interrupt-cells = <1>;
				};
			};
		};

		ocmcram1: ocmcram@40300000 {
			compatible = "mmio-sram";
			reg = <0x40300000 0x80000>;
			ranges = <0x0 0x40300000 0x80000>;
			#address-cells = <1>;
			#size-cells = <1>;
			/*
			 * This is a placeholder for an optional reserved
			 * region for use by secure software. The size
			 * of this region is not known until runtime so it
			 * is set as zero to either be updated to reserve
			 * space or left unchanged to leave all SRAM for use.
			 * On HS parts that that require the reserved region
			 * either the bootloader can update the size to
			 * the required amount or the node can be overridden
			 * from the board dts file for the secure platform.
			 */
			sram-hs@0 {
				compatible = "ti,secure-ram";
				reg = <0x0 0x0>;
			};
		};

		/*
		 * NOTE: ocmcram2 and ocmcram3 are not available on all
		 * DRA7xx and AM57xx variants. Confirm availability in
		 * the data manual for the exact part number in use
		 * before enabling these nodes in the board dts file.
		 */
		ocmcram2: ocmcram@40400000 {
			status = "disabled";
			compatible = "mmio-sram";
			reg = <0x40400000 0x100000>;
			ranges = <0x0 0x40400000 0x100000>;
			#address-cells = <1>;
			#size-cells = <1>;
		};

		ocmcram3: ocmcram@40500000 {
			status = "disabled";
			compatible = "mmio-sram";
			reg = <0x40500000 0x100000>;
			ranges = <0x0 0x40500000 0x100000>;
			#address-cells = <1>;
			#size-cells = <1>;
		};

		bandgap: bandgap@4a0021e0 {
			reg = <0x4a0021e0 0xc
				0x4a00232c 0xc
				0x4a002380 0x2c
				0x4a0023C0 0x3c
				0x4a002564 0x8
				0x4a002574 0x50>;
				compatible = "ti,dra752-bandgap";
				interrupts = <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>;
				#thermal-sensor-cells = <1>;
		};

		dsp1_system: dsp_system@40d00000 {
			compatible = "syscon";
			reg = <0x40d00000 0x100>;
		};

		dra7_iodelay_core: padconf@4844a000 {
			compatible = "ti,dra7-iodelay";
			reg = <0x4844a000 0x0d1c>;
			#address-cells = <1>;
			#size-cells = <0>;
			#pinctrl-cells = <2>;
		};

		target-module@43300000 {
			compatible = "ti,sysc-omap4", "ti,sysc";
			reg = <0x43300000 0x4>,
			      <0x43300010 0x4>;
			reg-names = "rev", "sysc";
			ti,sysc-midle = <SYSC_IDLE_FORCE>,
					<SYSC_IDLE_NO>,
					<SYSC_IDLE_SMART>;
			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
					<SYSC_IDLE_NO>,
					<SYSC_IDLE_SMART>;
			clocks = <&l3main1_clkctrl DRA7_L3MAIN1_TPCC_CLKCTRL 0>;
			clock-names = "fck";
			#address-cells = <1>;
			#size-cells = <1>;
			ranges = <0x0 0x43300000 0x100000>;

			edma: dma@0 {
				compatible = "ti,edma3-tpcc";
				reg = <0 0x100000>;
				reg-names = "edma3_cc";
				interrupts = <GIC_SPI 361 IRQ_TYPE_LEVEL_HIGH>,
					     <GIC_SPI 360 IRQ_TYPE_LEVEL_HIGH>,
					     <GIC_SPI 359 IRQ_TYPE_LEVEL_HIGH>;
				interrupt-names = "edma3_ccint", "edma3_mperr",
						  "edma3_ccerrint";
				dma-requests = <64>;
				#dma-cells = <2>;

				ti,tptcs = <&edma_tptc0 7>, <&edma_tptc1 0>;

				/*
				* memcpy is disabled, can be enabled with:
				* ti,edma-memcpy-channels = <20 21>;
				* for example. Note that these channels need to be
				* masked in the xbar as well.
				*/
			};
		};

		target-module@43400000 {
			compatible = "ti,sysc-omap4", "ti,sysc";
			reg = <0x43400000 0x4>,
			      <0x43400010 0x4>;
			reg-names = "rev", "sysc";
			ti,sysc-midle = <SYSC_IDLE_FORCE>,
					<SYSC_IDLE_NO>,
					<SYSC_IDLE_SMART>;
			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
					<SYSC_IDLE_NO>,
					<SYSC_IDLE_SMART>;
			clocks = <&l3main1_clkctrl DRA7_L3MAIN1_TPTC0_CLKCTRL 0>;
			clock-names = "fck";
			#address-cells = <1>;
			#size-cells = <1>;
			ranges = <0x0 0x43400000 0x100000>;

			edma_tptc0: dma@0 {
				compatible = "ti,edma3-tptc";
				reg = <0 0x100000>;
				interrupts = <GIC_SPI 370 IRQ_TYPE_LEVEL_HIGH>;
				interrupt-names = "edma3_tcerrint";
			};
		};

		target-module@43500000 {
			compatible = "ti,sysc-omap4", "ti,sysc";
			reg = <0x43500000 0x4>,
			      <0x43500010 0x4>;
			reg-names = "rev", "sysc";
			ti,sysc-midle = <SYSC_IDLE_FORCE>,
					<SYSC_IDLE_NO>,
					<SYSC_IDLE_SMART>;
			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
					<SYSC_IDLE_NO>,
					<SYSC_IDLE_SMART>;
			clocks = <&l3main1_clkctrl DRA7_L3MAIN1_TPTC1_CLKCTRL 0>;
			clock-names = "fck";
			#address-cells = <1>;
			#size-cells = <1>;
			ranges = <0x0 0x43500000 0x100000>;

			edma_tptc1: dma@0 {
				compatible = "ti,edma3-tptc";
				reg = <0 0x100000>;
				interrupts = <GIC_SPI 371 IRQ_TYPE_LEVEL_HIGH>;
				interrupt-names = "edma3_tcerrint";
			};
		};

		dmm@4e000000 {
			compatible = "ti,omap5-dmm";
			reg = <0x4e000000 0x800>;
			interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
			ti,hwmods = "dmm";
		};

		ipu1: ipu@58820000 {
			compatible = "ti,dra7-ipu";
			reg = <0x58820000 0x10000>;
			reg-names = "l2ram";
			iommus = <&mmu_ipu1>;
			status = "disabled";
			resets = <&prm_ipu 0>, <&prm_ipu 1>;
			clocks = <&ipu1_clkctrl DRA7_IPU1_MMU_IPU1_CLKCTRL 0>;
			firmware-name = "dra7-ipu1-fw.xem4";
		};

		ipu2: ipu@55020000 {
			compatible = "ti,dra7-ipu";
			reg = <0x55020000 0x10000>;
			reg-names = "l2ram";
			iommus = <&mmu_ipu2>;
			status = "disabled";
			resets = <&prm_core 0>, <&prm_core 1>;
			clocks = <&ipu2_clkctrl DRA7_IPU2_MMU_IPU2_CLKCTRL 0>;
			firmware-name = "dra7-ipu2-fw.xem4";
		};

		dsp1: dsp@40800000 {
			compatible = "ti,dra7-dsp";
			reg = <0x40800000 0x48000>,
			      <0x40e00000 0x8000>,
			      <0x40f00000 0x8000>;
			reg-names = "l2ram", "l1pram", "l1dram";
			ti,bootreg = <&scm_conf 0x55c 10>;
			iommus = <&mmu0_dsp1>, <&mmu1_dsp1>;
			status = "disabled";
			resets = <&prm_dsp1 0>;
			clocks = <&dsp1_clkctrl DRA7_DSP1_MMU0_DSP1_CLKCTRL 0>;
			firmware-name = "dra7-dsp1-fw.xe66";
		};

		target-module@40d01000 {
			compatible = "ti,sysc-omap2", "ti,sysc";
			reg = <0x40d01000 0x4>,
			      <0x40d01010 0x4>,
			      <0x40d01014 0x4>;
			reg-names = "rev", "sysc", "syss";
			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
					<SYSC_IDLE_NO>,
					<SYSC_IDLE_SMART>;
			ti,sysc-mask = <(SYSC_OMAP2_CLOCKACTIVITY |
					 SYSC_OMAP2_SOFTRESET |
					 SYSC_OMAP2_AUTOIDLE)>;
			clocks = <&dsp1_clkctrl DRA7_DSP1_MMU0_DSP1_CLKCTRL 0>;
			clock-names = "fck";
			resets = <&prm_dsp1 1>;
			reset-names = "rstctrl";
			ranges = <0x0 0x40d01000 0x1000>;
			#size-cells = <1>;
			#address-cells = <1>;

			mmu0_dsp1: mmu@0 {
				compatible = "ti,dra7-dsp-iommu";
				reg = <0x0 0x100>;
				interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>;
				#iommu-cells = <0>;
				ti,syscon-mmuconfig = <&dsp1_system 0x0>;
			};
		};

		target-module@40d02000 {
			compatible = "ti,sysc-omap2", "ti,sysc";
			reg = <0x40d02000 0x4>,
			      <0x40d02010 0x4>,
			      <0x40d02014 0x4>;
			reg-names = "rev", "sysc", "syss";
			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
					<SYSC_IDLE_NO>,
					<SYSC_IDLE_SMART>;
			ti,sysc-mask = <(SYSC_OMAP2_CLOCKACTIVITY |
					 SYSC_OMAP2_SOFTRESET |
					 SYSC_OMAP2_AUTOIDLE)>;
			clocks = <&dsp1_clkctrl DRA7_DSP1_MMU0_DSP1_CLKCTRL 0>;
			clock-names = "fck";
			resets = <&prm_dsp1 1>;
			reset-names = "rstctrl";
			ranges = <0x0 0x40d02000 0x1000>;
			#size-cells = <1>;
			#address-cells = <1>;

			mmu1_dsp1: mmu@0 {
				compatible = "ti,dra7-dsp-iommu";
				reg = <0x0 0x100>;
				interrupts = <GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>;
				#iommu-cells = <0>;
				ti,syscon-mmuconfig = <&dsp1_system 0x1>;
			};
		};

		target-module@58882000 {
			compatible = "ti,sysc-omap2", "ti,sysc";
			reg = <0x58882000 0x4>,
			      <0x58882010 0x4>,
			      <0x58882014 0x4>;
			reg-names = "rev", "sysc", "syss";
			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
					<SYSC_IDLE_NO>,
					<SYSC_IDLE_SMART>;
			ti,sysc-mask = <(SYSC_OMAP2_CLOCKACTIVITY |
					 SYSC_OMAP2_SOFTRESET |
					 SYSC_OMAP2_AUTOIDLE)>;
			clocks = <&ipu1_clkctrl DRA7_IPU1_MMU_IPU1_CLKCTRL 0>;
			clock-names = "fck";
			resets = <&prm_ipu 2>;
			reset-names = "rstctrl";
			#address-cells = <1>;
			#size-cells = <1>;
			ranges = <0x0 0x58882000 0x100>;

			mmu_ipu1: mmu@0 {
				compatible = "ti,dra7-iommu";
				reg = <0x0 0x100>;
				interrupts = <GIC_SPI 395 IRQ_TYPE_LEVEL_HIGH>;
				#iommu-cells = <0>;
				ti,iommu-bus-err-back;
			};
		};

		target-module@55082000 {
			compatible = "ti,sysc-omap2", "ti,sysc";
			reg = <0x55082000 0x4>,
			      <0x55082010 0x4>,
			      <0x55082014 0x4>;
			reg-names = "rev", "sysc", "syss";
			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
					<SYSC_IDLE_NO>,
					<SYSC_IDLE_SMART>;
			ti,sysc-mask = <(SYSC_OMAP2_CLOCKACTIVITY |
					 SYSC_OMAP2_SOFTRESET |
					 SYSC_OMAP2_AUTOIDLE)>;
			clocks = <&ipu2_clkctrl DRA7_IPU2_MMU_IPU2_CLKCTRL 0>;
			clock-names = "fck";
			resets = <&prm_core 2>;
			reset-names = "rstctrl";
			#address-cells = <1>;
			#size-cells = <1>;
			ranges = <0x0 0x55082000 0x100>;

			mmu_ipu2: mmu@0 {
				compatible = "ti,dra7-iommu";
				reg = <0x0 0x100>;
				interrupts = <GIC_SPI 396 IRQ_TYPE_LEVEL_HIGH>;
				#iommu-cells = <0>;
				ti,iommu-bus-err-back;
			};
		};

		abb_mpu: regulator-abb-mpu {
			compatible = "ti,abb-v3";
			regulator-name = "abb_mpu";
			#address-cells = <0>;
			#size-cells = <0>;
			clocks = <&sys_clkin1>;
			ti,settling-time = <50>;
			ti,clock-cycles = <16>;

			reg = <0x4ae07ddc 0x4>, <0x4ae07de0 0x4>,
			      <0x4ae06014 0x4>, <0x4a003b20 0xc>,
			      <0x4ae0c158 0x4>;
			reg-names = "setup-address", "control-address",
				    "int-address", "efuse-address",
				    "ldo-address";
			ti,tranxdone-status-mask = <0x80>;
			/* LDOVBBMPU_FBB_MUX_CTRL */
			ti,ldovbb-override-mask = <0x400>;
			/* LDOVBBMPU_FBB_VSET_OUT */
			ti,ldovbb-vset-mask = <0x1F>;

			/*
			 * NOTE: only FBB mode used but actual vset will
			 * determine final biasing
			 */
			ti,abb_info = <
			/*uV		ABB	efuse	rbb_m fbb_m	vset_m*/
			1060000		0	0x0	0 0x02000000 0x01F00000
			1160000		0	0x4	0 0x02000000 0x01F00000
			1210000		0	0x8	0 0x02000000 0x01F00000
			>;
		};

		abb_ivahd: regulator-abb-ivahd {
			compatible = "ti,abb-v3";
			regulator-name = "abb_ivahd";
			#address-cells = <0>;
			#size-cells = <0>;
			clocks = <&sys_clkin1>;
			ti,settling-time = <50>;
			ti,clock-cycles = <16>;

			reg = <0x4ae07e34 0x4>, <0x4ae07e24 0x4>,
			      <0x4ae06010 0x4>, <0x4a0025cc 0xc>,
			      <0x4a002470 0x4>;
			reg-names = "setup-address", "control-address",
				    "int-address", "efuse-address",
				    "ldo-address";
			ti,tranxdone-status-mask = <0x40000000>;
			/* LDOVBBIVA_FBB_MUX_CTRL */
			ti,ldovbb-override-mask = <0x400>;
			/* LDOVBBIVA_FBB_VSET_OUT */
			ti,ldovbb-vset-mask = <0x1F>;

			/*
			 * NOTE: only FBB mode used but actual vset will
			 * determine final biasing
			 */
			ti,abb_info = <
			/*uV		ABB	efuse	rbb_m fbb_m	vset_m*/
			1055000		0	0x0	0 0x02000000 0x01F00000
			1150000		0	0x4	0 0x02000000 0x01F00000
			1250000		0	0x8	0 0x02000000 0x01F00000
			>;
		};

		abb_dspeve: regulator-abb-dspeve {
			compatible = "ti,abb-v3";
			regulator-name = "abb_dspeve";
			#address-cells = <0>;
			#size-cells = <0>;
			clocks = <&sys_clkin1>;
			ti,settling-time = <50>;
			ti,clock-cycles = <16>;

			reg = <0x4ae07e30 0x4>, <0x4ae07e20 0x4>,
			      <0x4ae06010 0x4>, <0x4a0025e0 0xc>,
			      <0x4a00246c 0x4>;
			reg-names = "setup-address", "control-address",
				    "int-address", "efuse-address",
				    "ldo-address";
			ti,tranxdone-status-mask = <0x20000000>;
			/* LDOVBBDSPEVE_FBB_MUX_CTRL */
			ti,ldovbb-override-mask = <0x400>;
			/* LDOVBBDSPEVE_FBB_VSET_OUT */
			ti,ldovbb-vset-mask = <0x1F>;

			/*
			 * NOTE: only FBB mode used but actual vset will
			 * determine final biasing
			 */
			ti,abb_info = <
			/*uV		ABB	efuse	rbb_m fbb_m	vset_m*/
			1055000		0	0x0	0 0x02000000 0x01F00000
			1150000		0	0x4	0 0x02000000 0x01F00000
			1250000		0	0x8	0 0x02000000 0x01F00000
			>;
		};

		abb_gpu: regulator-abb-gpu {
			compatible = "ti,abb-v3";
			regulator-name = "abb_gpu";
			#address-cells = <0>;
			#size-cells = <0>;
			clocks = <&sys_clkin1>;
			ti,settling-time = <50>;
			ti,clock-cycles = <16>;

			reg = <0x4ae07de4 0x4>, <0x4ae07de8 0x4>,
			      <0x4ae06010 0x4>, <0x4a003b08 0xc>,
			      <0x4ae0c154 0x4>;
			reg-names = "setup-address", "control-address",
				    "int-address", "efuse-address",
				    "ldo-address";
			ti,tranxdone-status-mask = <0x10000000>;
			/* LDOVBBGPU_FBB_MUX_CTRL */
			ti,ldovbb-override-mask = <0x400>;
			/* LDOVBBGPU_FBB_VSET_OUT */
			ti,ldovbb-vset-mask = <0x1F>;

			/*
			 * NOTE: only FBB mode used but actual vset will
			 * determine final biasing
			 */
			ti,abb_info = <
			/*uV		ABB	efuse	rbb_m fbb_m	vset_m*/
			1090000		0	0x0	0 0x02000000 0x01F00000
			1210000		0	0x4	0 0x02000000 0x01F00000
			1280000		0	0x8	0 0x02000000 0x01F00000
			>;
		};

		target-module@4b300000 {
			compatible = "ti,sysc-omap4", "ti,sysc";
			ti,hwmods = "qspi";
			reg = <0x4b300000 0x4>,
			      <0x4b300010 0x4>;
			reg-names = "rev", "sysc";
			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
					<SYSC_IDLE_NO>,
					<SYSC_IDLE_SMART>,
					<SYSC_IDLE_SMART_WKUP>;
			clocks = <&l4per2_clkctrl DRA7_L4PER2_QSPI_CLKCTRL 0>;
			clock-names = "fck";
			#address-cells = <1>;
			#size-cells = <1>;
			ranges = <0x0 0x4b300000 0x1000>,
				 <0x5c000000 0x5c000000 0x4000000>;

			qspi: spi@0 {
				compatible = "ti,dra7xxx-qspi";
				reg = <0 0x100>,
				      <0x5c000000 0x4000000>;
				reg-names = "qspi_base", "qspi_mmap";
				syscon-chipselects = <&scm_conf 0x558>;
				#address-cells = <1>;
				#size-cells = <0>;
				clocks = <&l4per2_clkctrl DRA7_L4PER2_QSPI_CLKCTRL 25>;
				clock-names = "fck";
				num-cs = <4>;
				interrupts = <GIC_SPI 343 IRQ_TYPE_LEVEL_HIGH>;
				status = "disabled";
			};
		};

		/* OCP2SCP3 */
		sata: sata@4a141100 {
			compatible = "snps,dwc-ahci";
			reg = <0x4a140000 0x1100>, <0x4a141100 0x7>;
			interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>;
			phys = <&sata_phy>;
			phy-names = "sata-phy";
			clocks = <&l3init_clkctrl DRA7_L3INIT_SATA_CLKCTRL 8>;
			ti,hwmods = "sata";
			ports-implemented = <0x1>;
		};

		/* OCP2SCP1 */
		/* IRQ for DWC3_3 and DWC3_4 need IRQ crossbar */

		target-module@50000000 {
			compatible = "ti,sysc-omap2", "ti,sysc";
			reg = <0x50000000 4>,
			      <0x50000010 4>,
			      <0x50000014 4>;
			reg-names = "rev", "sysc", "syss";
			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
					<SYSC_IDLE_NO>,
					<SYSC_IDLE_SMART>;
			ti,syss-mask = <1>;
			clocks = <&l3main1_clkctrl DRA7_L3MAIN1_GPMC_CLKCTRL 0>;
			clock-names = "fck";
			#address-cells = <1>;
			#size-cells = <1>;
			ranges = <0x50000000 0x50000000 0x00001000>, /* regs */
				 <0x00000000 0x00000000 0x40000000>; /* data */

			gpmc: gpmc@50000000 {
				compatible = "ti,am3352-gpmc";
				reg = <0x50000000 0x37c>;      /* device IO registers */
				interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>;
				dmas = <&edma_xbar 4 0>;
				dma-names = "rxtx";
				gpmc,num-cs = <8>;
				gpmc,num-waitpins = <2>;
				#address-cells = <2>;
				#size-cells = <1>;
				interrupt-controller;
				#interrupt-cells = <2>;
				gpio-controller;
				#gpio-cells = <2>;
				status = "disabled";
			};
		};

		target-module@56000000 {
			compatible = "ti,sysc-omap4", "ti,sysc";
			reg = <0x5600fe00 0x4>,
			      <0x5600fe10 0x4>;
			reg-names = "rev", "sysc";
			ti,sysc-midle = <SYSC_IDLE_FORCE>,
					<SYSC_IDLE_NO>,
					<SYSC_IDLE_SMART>;
			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
					<SYSC_IDLE_NO>,
					<SYSC_IDLE_SMART>;
			clocks = <&gpu_clkctrl DRA7_GPU_CLKCTRL 0>;
			clock-names = "fck";
			#address-cells = <1>;
			#size-cells = <1>;
			ranges = <0 0x56000000 0x2000000>;
		};

		crossbar_mpu: crossbar@4a002a48 {
			compatible = "ti,irq-crossbar";
			reg = <0x4a002a48 0x130>;
			interrupt-controller;
			interrupt-parent = <&wakeupgen>;
			#interrupt-cells = <3>;
			ti,max-irqs = <160>;
			ti,max-crossbar-sources = <MAX_SOURCES>;
			ti,reg-size = <2>;
			ti,irqs-reserved = <0 1 2 3 5 6 131 132>;
			ti,irqs-skip = <10 133 139 140>;
			ti,irqs-safe-map = <0>;
		};

		target-module@58000000 {
			compatible = "ti,sysc-omap2", "ti,sysc";
			reg = <0x58000000 4>,
			      <0x58000014 4>;
			reg-names = "rev", "syss";
			ti,syss-mask = <1>;
			clocks = <&dss_clkctrl DRA7_DSS_CORE_CLKCTRL 0>,
				 <&dss_clkctrl DRA7_DSS_CORE_CLKCTRL 9>,
				 <&dss_clkctrl DRA7_DSS_CORE_CLKCTRL 10>,
				 <&dss_clkctrl DRA7_DSS_CORE_CLKCTRL 11>;
			clock-names = "fck", "hdmi_clk", "sys_clk", "tv_clk";
			#address-cells = <1>;
			#size-cells = <1>;
			ranges = <0 0x58000000 0x800000>;

			dss: dss@0 {
				compatible = "ti,dra7-dss";
				/* 'reg' defined in dra72x.dtsi and dra74x.dtsi */
				/* 'clocks' defined in dra72x.dtsi and dra74x.dtsi */
				status = "disabled";
				/* CTRL_CORE_DSS_PLL_CONTROL */
				syscon-pll-ctrl = <&scm_conf 0x538>;
				#address-cells = <1>;
				#size-cells = <1>;
				ranges = <0 0 0x800000>;

				target-module@1000 {
					compatible = "ti,sysc-omap2", "ti,sysc";
					reg = <0x1000 0x4>,
					      <0x1010 0x4>,
					      <0x1014 0x4>;
					reg-names = "rev", "sysc", "syss";
					ti,sysc-sidle = <SYSC_IDLE_FORCE>,
							<SYSC_IDLE_NO>,
							<SYSC_IDLE_SMART>;
					ti,sysc-midle = <SYSC_IDLE_FORCE>,
							<SYSC_IDLE_NO>,
							<SYSC_IDLE_SMART>;
					ti,sysc-mask = <(SYSC_OMAP2_CLOCKACTIVITY |
							 SYSC_OMAP2_ENAWAKEUP |
							 SYSC_OMAP2_SOFTRESET |
							 SYSC_OMAP2_AUTOIDLE)>;
					ti,syss-mask = <1>;
					clocks = <&dss_clkctrl DRA7_DSS_CORE_CLKCTRL 8>;
					clock-names = "fck";
					#address-cells = <1>;
					#size-cells = <1>;
					ranges = <0 0x1000 0x1000>;

					dispc@0 {
						compatible = "ti,dra7-dispc";
						reg = <0 0x1000>;
						interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>;
						clocks = <&dss_clkctrl DRA7_DSS_DSS_CORE_CLKCTRL 8>;
						clock-names = "fck";
						/* CTRL_CORE_SMA_SW_1 */
						syscon-pol = <&scm_conf 0x534>;
					};
				};

				target-module@40000 {
					compatible = "ti,sysc-omap4", "ti,sysc";
					reg = <0x40000 0x4>,
					      <0x40010 0x4>;
					reg-names = "rev", "sysc";
					ti,sysc-sidle = <SYSC_IDLE_FORCE>,
							<SYSC_IDLE_NO>,
							<SYSC_IDLE_SMART>,
							<SYSC_IDLE_SMART_WKUP>;
					ti,sysc-mask = <(SYSC_OMAP4_SOFTRESET)>;
					clocks = <&dss_clkctrl DRA7_DSS_CORE_CLKCTRL 9>,
						 <&dss_clkctrl DRA7_DSS_CORE_CLKCTRL 8>;
					clock-names = "fck", "dss_clk";
					#address-cells = <1>;
					#size-cells = <1>;
					ranges = <0 0x40000 0x40000>;

					hdmi: encoder@0 {
						compatible = "ti,dra7-hdmi";
						reg = <0 0x200>,
						      <0x200 0x80>,
						      <0x300 0x80>,
						      <0x20000 0x19000>;
						reg-names = "wp", "pll", "phy", "core";
						interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
						status = "disabled";
						clocks = <&dss_clkctrl DRA7_DSS_DSS_CORE_CLKCTRL 9>,
							 <&dss_clkctrl DRA7_DSS_DSS_CORE_CLKCTRL 10>;
						clock-names = "fck", "sys_clk";
						dmas = <&sdma_xbar 76>;
						dma-names = "audio_tx";
					};
				};
			};
		};

		aes1_target: target-module@4b500000 {
			compatible = "ti,sysc-omap2", "ti,sysc";
			reg = <0x4b500080 0x4>,
			      <0x4b500084 0x4>,
			      <0x4b500088 0x4>;
			reg-names = "rev", "sysc", "syss";
			ti,sysc-mask = <(SYSC_OMAP2_SOFTRESET |
					 SYSC_OMAP2_AUTOIDLE)>;
			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
					<SYSC_IDLE_NO>,
					<SYSC_IDLE_SMART>,
					<SYSC_IDLE_SMART_WKUP>;
			ti,syss-mask = <1>;
			/* Domains (P, C): per_pwrdm, l4sec_clkdm */
			clocks = <&l4sec_clkctrl DRA7_L4SEC_AES1_CLKCTRL 0>;
			clock-names = "fck";
			#address-cells = <1>;
			#size-cells = <1>;
			ranges = <0x0 0x4b500000 0x1000>;

			aes1: aes@0 {
				compatible = "ti,omap4-aes";
				reg = <0 0xa0>;
				interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>;
				dmas = <&edma_xbar 111 0>, <&edma_xbar 110 0>;
				dma-names = "tx", "rx";
				clocks = <&l3_iclk_div>;
				clock-names = "fck";
			};
		};

		aes2_target: target-module@4b700000 {
			compatible = "ti,sysc-omap2", "ti,sysc";
			reg = <0x4b700080 0x4>,
			      <0x4b700084 0x4>,
			      <0x4b700088 0x4>;
			reg-names = "rev", "sysc", "syss";
			ti,sysc-mask = <(SYSC_OMAP2_SOFTRESET |
					 SYSC_OMAP2_AUTOIDLE)>;
			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
					<SYSC_IDLE_NO>,
					<SYSC_IDLE_SMART>,
					<SYSC_IDLE_SMART_WKUP>;
			ti,syss-mask = <1>;
			/* Domains (P, C): per_pwrdm, l4sec_clkdm */
			clocks = <&l4sec_clkctrl DRA7_L4SEC_AES2_CLKCTRL 0>;
			clock-names = "fck";
			#address-cells = <1>;
			#size-cells = <1>;
			ranges = <0x0 0x4b700000 0x1000>;

			aes2: aes@0 {
				compatible = "ti,omap4-aes";
				reg = <0 0xa0>;
				interrupts = <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>;
				dmas = <&edma_xbar 114 0>, <&edma_xbar 113 0>;
				dma-names = "tx", "rx";
				clocks = <&l3_iclk_div>;
				clock-names = "fck";
			};
		};

		sham1_target: target-module@4b101000 {
			compatible = "ti,sysc-omap3-sham", "ti,sysc";
			reg = <0x4b101100 0x4>,
			      <0x4b101110 0x4>,
			      <0x4b101114 0x4>;
			reg-names = "rev", "sysc", "syss";
			ti,sysc-mask = <(SYSC_OMAP2_SOFTRESET |
					 SYSC_OMAP2_AUTOIDLE)>;
			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
					<SYSC_IDLE_NO>,
					<SYSC_IDLE_SMART>;
			ti,syss-mask = <1>;
			/* Domains (P, C): l4per_pwrdm, l4sec_clkdm */
			clocks = <&l4sec_clkctrl DRA7_L4SEC_SHAM_CLKCTRL 0>;
			clock-names = "fck";
			#address-cells = <1>;
			#size-cells = <1>;
			ranges = <0x0 0x4b101000 0x1000>;

			sham1: sham@0 {
				compatible = "ti,omap5-sham";
				reg = <0 0x300>;
				interrupts = <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>;
				dmas = <&edma_xbar 119 0>;
				dma-names = "rx";
				clocks = <&l3_iclk_div>;
				clock-names = "fck";
			};
		};

		sham2_target: target-module@42701000 {
			compatible = "ti,sysc-omap3-sham", "ti,sysc";
			reg = <0x42701100 0x4>,
			      <0x42701110 0x4>,
			      <0x42701114 0x4>;
			reg-names = "rev", "sysc", "syss";
			ti,sysc-mask = <(SYSC_OMAP2_SOFTRESET |
					 SYSC_OMAP2_AUTOIDLE)>;
			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
					<SYSC_IDLE_NO>,
					<SYSC_IDLE_SMART>;
			ti,syss-mask = <1>;
			/* Domains (P, C): l4per_pwrdm, l4sec_clkdm */
			clocks = <&l4sec_clkctrl DRA7_L4SEC_SHAM2_CLKCTRL 0>;
			clock-names = "fck";
			#address-cells = <1>;
			#size-cells = <1>;
			ranges = <0x0 0x42701000 0x1000>;

			sham2: sham@0 {
				compatible = "ti,omap5-sham";
				reg = <0 0x300>;
				interrupts = <GIC_SPI 163 IRQ_TYPE_LEVEL_HIGH>;
				dmas = <&edma_xbar 165 0>;
				dma-names = "rx";
				clocks = <&l3_iclk_div>;
				clock-names = "fck";
			};
		};

		iva_hd_target: target-module@5a000000 {
			compatible = "ti,sysc-omap4", "ti,sysc";
			reg = <0x5a05a400 0x4>,
			      <0x5a05a410 0x4>;
			reg-names = "rev", "sysc";
			ti,sysc-midle = <SYSC_IDLE_FORCE>,
					<SYSC_IDLE_NO>,
					<SYSC_IDLE_SMART>;
			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
					<SYSC_IDLE_NO>,
					<SYSC_IDLE_SMART>;
			power-domains = <&prm_iva>;
			resets = <&prm_iva 2>;
			reset-names = "rstctrl";
			clocks = <&iva_clkctrl DRA7_IVA_CLKCTRL 0>;
			clock-names = "fck";
			#address-cells = <1>;
			#size-cells = <1>;
			ranges = <0x5a000000 0x5a000000 0x1000000>,
				 <0x5b000000 0x5b000000 0x1000000>;

			iva {
				compatible = "ti,ivahd";
			};
		};

		opp_supply_mpu: opp-supply@4a003b20 {
			compatible = "ti,omap5-opp-supply";
			reg = <0x4a003b20 0xc>;
			ti,efuse-settings = <
			/* uV   offset */
			1060000 0x0
			1160000 0x4
			1210000 0x8
			>;
			ti,absolute-max-voltage-uv = <1500000>;
		};

	};

	thermal_zones: thermal-zones {
		#include "omap4-cpu-thermal.dtsi"
		#include "omap5-gpu-thermal.dtsi"
		#include "omap5-core-thermal.dtsi"
		#include "dra7-dspeve-thermal.dtsi"
		#include "dra7-iva-thermal.dtsi"
	};

};

&cpu_thermal {
	polling-delay = <500>; /* milliseconds */
	coefficients = <0 2000>;
};

&gpu_thermal {
	coefficients = <0 2000>;
};

&core_thermal {
	coefficients = <0 2000>;
};

&dspeve_thermal {
	coefficients = <0 2000>;
};

&iva_thermal {
	coefficients = <0 2000>;
};

&cpu_crit {
	temperature = <120000>; /* milli Celsius */
};

&core_crit {
	temperature = <120000>; /* milli Celsius */
};

&gpu_crit {
	temperature = <120000>; /* milli Celsius */
};

&dspeve_crit {
	temperature = <120000>; /* milli Celsius */
};

&iva_crit {
	temperature = <120000>; /* milli Celsius */
};

#include "dra7-l4.dtsi"
#include "dra7xx-clocks.dtsi"

&prm {
	prm_mpu: prm@300 {
		compatible = "ti,dra7-prm-inst", "ti,omap-prm-inst";
		reg = <0x300 0x100>;
		#power-domain-cells = <0>;
	};

	prm_dsp1: prm@400 {
		compatible = "ti,dra7-prm-inst", "ti,omap-prm-inst";
		reg = <0x400 0x100>;
		#reset-cells = <1>;
		#power-domain-cells = <0>;
	};

	prm_ipu: prm@500 {
		compatible = "ti,dra7-prm-inst", "ti,omap-prm-inst";
		reg = <0x500 0x100>;
		#reset-cells = <1>;
		#power-domain-cells = <0>;
	};

	prm_coreaon: prm@628 {
		compatible = "ti,dra7-prm-inst", "ti,omap-prm-inst";
		reg = <0x628 0xd8>;
		#power-domain-cells = <0>;
	};

	prm_core: prm@700 {
		compatible = "ti,dra7-prm-inst", "ti,omap-prm-inst";
		reg = <0x700 0x100>;
		#reset-cells = <1>;
		#power-domain-cells = <0>;
	};

	prm_iva: prm@f00 {
		compatible = "ti,dra7-prm-inst", "ti,omap-prm-inst";
		reg = <0xf00 0x100>;
		#reset-cells = <1>;
		#power-domain-cells = <0>;
	};

	prm_cam: prm@1000 {
		compatible = "ti,dra7-prm-inst", "ti,omap-prm-inst";
		reg = <0x1000 0x100>;
		#power-domain-cells = <0>;
	};

	prm_dss: prm@1100 {
		compatible = "ti,dra7-prm-inst", "ti,omap-prm-inst";
		reg = <0x1100 0x100>;
		#power-domain-cells = <0>;
	};

	prm_gpu: prm@1200 {
		compatible = "ti,dra7-prm-inst", "ti,omap-prm-inst";
		reg = <0x1200 0x100>;
		#power-domain-cells = <0>;
	};

	prm_l3init: prm@1300 {
		compatible = "ti,dra7-prm-inst", "ti,omap-prm-inst";
		reg = <0x1300 0x100>;
		#reset-cells = <1>;
		#power-domain-cells = <0>;
	};

	prm_l4per: prm@1400 {
		compatible = "ti,dra7-prm-inst", "ti,omap-prm-inst";
		reg = <0x1400 0x100>;
		#power-domain-cells = <0>;
	};

	prm_custefuse: prm@1600 {
		compatible = "ti,dra7-prm-inst", "ti,omap-prm-inst";
		reg = <0x1600 0x100>;
		#power-domain-cells = <0>;
	};

	prm_wkupaon: prm@1724 {
		compatible = "ti,dra7-prm-inst", "ti,omap-prm-inst";
		reg = <0x1724 0x100>;
		#power-domain-cells = <0>;
	};

	prm_dsp2: prm@1b00 {
		compatible = "ti,dra7-prm-inst", "ti,omap-prm-inst";
		reg = <0x1b00 0x40>;
		#reset-cells = <1>;
		#power-domain-cells = <0>;
	};

	prm_eve1: prm@1b40 {
		compatible = "ti,dra7-prm-inst", "ti,omap-prm-inst";
		reg = <0x1b40 0x40>;
		#power-domain-cells = <0>;
	};

	prm_eve2: prm@1b80 {
		compatible = "ti,dra7-prm-inst", "ti,omap-prm-inst";
		reg = <0x1b80 0x40>;
		#power-domain-cells = <0>;
	};

	prm_eve3: prm@1bc0 {
		compatible = "ti,dra7-prm-inst", "ti,omap-prm-inst";
		reg = <0x1bc0 0x40>;
		#power-domain-cells = <0>;
	};

	prm_eve4: prm@1c00 {
		compatible = "ti,dra7-prm-inst", "ti,omap-prm-inst";
		reg = <0x1c00 0x60>;
		#power-domain-cells = <0>;
	};

	prm_rtc: prm@1c60 {
		compatible = "ti,dra7-prm-inst", "ti,omap-prm-inst";
		reg = <0x1c60 0x20>;
		#power-domain-cells = <0>;
	};

	prm_vpe: prm@1c80 {
		compatible = "ti,dra7-prm-inst", "ti,omap-prm-inst";
		reg = <0x1c80 0x80>;
		#power-domain-cells = <0>;
	};
};

/* Preferred always-on timer for clockevent */
&timer1_target {
	ti,no-reset-on-init;
	ti,no-idle;
	timer@0 {
		assigned-clocks = <&wkupaon_clkctrl DRA7_TIMER1_CLKCTRL 24>;
		assigned-clock-parents = <&sys_32k_ck>;
	};
};