blob: 1b3c13d206ffed5150ac78f0beefb159fc44eaba [file] [log] [blame]
Anatol Pomozovf9f6a592014-09-17 13:14:20 -07001RT5677 audio CODEC
2
3This device supports I2C only.
4
5Required properties:
6
7- compatible : "realtek,rt5677".
8
9- reg : The I2C address of the device.
10
11- interrupts : The CODEC's interrupt output.
12
Anatol Pomozov0e612ff2014-09-24 11:31:58 -070013- gpio-controller : Indicates this device is a GPIO controller.
14
15- #gpio-cells : Should be two. The first cell is the pin number and the
16 second cell is used to specify optional parameters (currently unused).
17
Anatol Pomozovf9f6a592014-09-17 13:14:20 -070018Optional properties:
19
20- realtek,pow-ldo2-gpio : The GPIO that controls the CODEC's POW_LDO2 pin.
Anatol Pomozovcdab0d42015-10-29 15:31:59 -070021- realtek,reset-gpio : The GPIO that controls the CODEC's RESET pin. Active low.
Anatol Pomozovf9f6a592014-09-17 13:14:20 -070022
Anatol Pomozov6f67c382014-09-26 09:57:27 -070023- realtek,in1-differential
24- realtek,in2-differential
25- realtek,lout1-differential
26- realtek,lout2-differential
27- realtek,lout3-differential
28 Boolean. Indicate MIC1/2 input and LOUT1/2/3 outputs are differential,
29 rather than single-ended.
30
Anatol Pomozov40eb90a2014-10-10 20:46:36 -070031- realtek,gpio-config
32 Array of six 8bit elements that configures GPIO.
33 0 - floating (reset value)
34 1 - pull down
35 2 - pull up
36
Oder Chiou5e3363a2014-10-16 11:24:26 -070037- realtek,jd1-gpio
38 Configures GPIO Mic Jack detection 1.
39 Select 0 ~ 3 as OFF, GPIO1, GPIO2 and GPIO3 respectively.
40
41- realtek,jd2-gpio
42- realtek,jd3-gpio
43 Configures GPIO Mic Jack detection 2 and 3.
44 Select 0 ~ 3 as OFF, GPIO4, GPIO5 and GPIO6 respectively.
45
Anatol Pomozovf9f6a592014-09-17 13:14:20 -070046Pins on the device (for linking into audio routes):
47
48 * IN1P
49 * IN1N
50 * IN2P
51 * IN2N
52 * MICBIAS1
53 * DMIC1
54 * DMIC2
55 * DMIC3
56 * DMIC4
57 * LOUT1
58 * LOUT2
59 * LOUT3
60
61Example:
62
63rt5677 {
64 compatible = "realtek,rt5677";
65 reg = <0x2c>;
66 interrupt-parent = <&gpio>;
67 interrupts = <TEGRA_GPIO(W, 3) GPIO_ACTIVE_HIGH>;
Anatol Pomozov0e612ff2014-09-24 11:31:58 -070068
69 gpio-controller;
70 #gpio-cells = <2>;
71
Anatol Pomozovf9f6a592014-09-17 13:14:20 -070072 realtek,pow-ldo2-gpio =
73 <&gpio TEGRA_GPIO(V, 3) GPIO_ACTIVE_HIGH>;
Anatol Pomozovb3b10e92015-05-13 08:25:15 -070074 realtek,reset-gpio = <&gpio TEGRA_GPIO(BB, 3) GPIO_ACTIVE_LOW>;
Anatol Pomozov6f67c382014-09-26 09:57:27 -070075 realtek,in1-differential = "true";
Anatol Pomozov40eb90a2014-10-10 20:46:36 -070076 realtek,gpio-config = /bits/ 8 <0 0 0 0 0 2>; /* pull up GPIO6 */
Oder Chiou5e3363a2014-10-16 11:24:26 -070077 realtek,jd2-gpio = <3>; /* Enables Jack detection for GPIO6 */
Anatol Pomozovf9f6a592014-09-17 13:14:20 -070078};