| stephen hemminger | a5050c6 | 2017-08-01 19:58:54 -0700 | [diff] [blame] | 1 | Hyper-V network driver |
| 2 | ====================== |
| 3 | |
| 4 | Compatibility |
| 5 | ============= |
| 6 | |
| 7 | This driver is compatible with Windows Server 2012 R2, 2016 and |
| 8 | Windows 10. |
| 9 | |
| 10 | Features |
| 11 | ======== |
| 12 | |
| 13 | Checksum offload |
| 14 | ---------------- |
| 15 | The netvsc driver supports checksum offload as long as the |
| 16 | Hyper-V host version does. Windows Server 2016 and Azure |
| 17 | support checksum offload for TCP and UDP for both IPv4 and |
| 18 | IPv6. Windows Server 2012 only supports checksum offload for TCP. |
| 19 | |
| 20 | Receive Side Scaling |
| 21 | -------------------- |
| Haiyang Zhang | 78005d9 | 2017-10-06 08:33:59 -0700 | [diff] [blame] | 22 | Hyper-V supports receive side scaling. For TCP & UDP, packets can |
| 23 | be distributed among available queues based on IP address and port |
| Haiyang Zhang | 3b0c345 | 2017-08-21 19:22:40 -0700 | [diff] [blame] | 24 | number. |
| 25 | |
| Haiyang Zhang | 78005d9 | 2017-10-06 08:33:59 -0700 | [diff] [blame] | 26 | For TCP & UDP, we can switch hash level between L3 and L4 by ethtool |
| 27 | command. TCP/UDP over IPv4 and v6 can be set differently. The default |
| Haiyang Zhang | 3b0c345 | 2017-08-21 19:22:40 -0700 | [diff] [blame] | 28 | hash level is L4. We currently only allow switching TX hash level |
| 29 | from within the guests. |
| 30 | |
| 31 | On Azure, fragmented UDP packets have high loss rate with L4 |
| 32 | hashing. Using L3 hashing is recommended in this case. |
| 33 | |
| 34 | For example, for UDP over IPv4 on eth0: |
| Haiyang Zhang | d35d6e9 | 2017-08-30 13:37:22 -0700 | [diff] [blame] | 35 | To include UDP port numbers in hashing: |
| Haiyang Zhang | 3b0c345 | 2017-08-21 19:22:40 -0700 | [diff] [blame] | 36 | ethtool -N eth0 rx-flow-hash udp4 sdfn |
| Haiyang Zhang | d35d6e9 | 2017-08-30 13:37:22 -0700 | [diff] [blame] | 37 | To exclude UDP port numbers in hashing: |
| Haiyang Zhang | 3b0c345 | 2017-08-21 19:22:40 -0700 | [diff] [blame] | 38 | ethtool -N eth0 rx-flow-hash udp4 sd |
| 39 | To show UDP hash level: |
| 40 | ethtool -n eth0 rx-flow-hash udp4 |
| stephen hemminger | a5050c6 | 2017-08-01 19:58:54 -0700 | [diff] [blame] | 41 | |
| 42 | Generic Receive Offload, aka GRO |
| 43 | -------------------------------- |
| 44 | The driver supports GRO and it is enabled by default. GRO coalesces |
| 45 | like packets and significantly reduces CPU usage under heavy Rx |
| 46 | load. |
| 47 | |
| 48 | SR-IOV support |
| 49 | -------------- |
| 50 | Hyper-V supports SR-IOV as a hardware acceleration option. If SR-IOV |
| 51 | is enabled in both the vSwitch and the guest configuration, then the |
| 52 | Virtual Function (VF) device is passed to the guest as a PCI |
| 53 | device. In this case, both a synthetic (netvsc) and VF device are |
| 54 | visible in the guest OS and both NIC's have the same MAC address. |
| 55 | |
| 56 | The VF is enslaved by netvsc device. The netvsc driver will transparently |
| 57 | switch the data path to the VF when it is available and up. |
| 58 | Network state (addresses, firewall, etc) should be applied only to the |
| 59 | netvsc device; the slave device should not be accessed directly in |
| 60 | most cases. The exceptions are if some special queue discipline or |
| 61 | flow direction is desired, these should be applied directly to the |
| 62 | VF slave device. |
| 63 | |
| 64 | Receive Buffer |
| 65 | -------------- |
| 66 | Packets are received into a receive area which is created when device |
| 67 | is probed. The receive area is broken into MTU sized chunks and each may |
| 68 | contain one or more packets. The number of receive sections may be changed |
| 69 | via ethtool Rx ring parameters. |
| 70 | |
| 71 | There is a similar send buffer which is used to aggregate packets for sending. |
| 72 | The send area is broken into chunks of 6144 bytes, each of section may |
| 73 | contain one or more packets. The send buffer is an optimization, the driver |
| 74 | will use slower method to handle very large packets or if the send buffer |
| 75 | area is exhausted. |