arch/arm/mach-msm/acpuclock-arm11.c

/* arch/arm/mach-msm/acpuclock.c
 *
 * MSM architecture clock driver
 *
 * Copyright (C) 2007 Google, Inc.
 * Copyright (c) 2007 QUALCOMM Incorporated
 * Author: San Mehat <san@android.com>
 *
 * This software is licensed under the terms of the GNU General Public
 * License version 2, as published by the Free Software Foundation, and
 * may be copied, distributed, and modified under those terms.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
 * GNU General Public License for more details.
 *
 */

#include <linux/version.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/list.h>
#include <linux/errno.h>
#include <linux/string.h>
#include <linux/delay.h>
#include <linux/clk.h>
#include <linux/cpufreq.h>
#include <linux/mutex.h>
#include <linux/io.h>
#include <mach/board.h>
#include <mach/msm_iomap.h>

#include "proc_comm.h"
#include "acpuclock.h"


#define A11S_CLK_CNTL_ADDR (MSM_CSR_BASE + 0x100)
#define A11S_CLK_SEL_ADDR (MSM_CSR_BASE + 0x104)
#define A11S_VDD_SVS_PLEVEL_ADDR (MSM_CSR_BASE + 0x124)

/*
 * ARM11 clock configuration for specific ACPU speeds
 */

#define ACPU_PLL_TCXO	-1
#define ACPU_PLL_0	0
#define ACPU_PLL_1	1
#define ACPU_PLL_2	2
#define ACPU_PLL_3	3

#define PERF_SWITCH_DEBUG 0
#define PERF_SWITCH_STEP_DEBUG 0

struct clock_state
{
	struct clkctl_acpu_speed	*current_speed;
	struct mutex			lock;
	uint32_t			acpu_switch_time_us;
	uint32_t			max_speed_delta_khz;
	uint32_t			vdd_switch_time_us;
	unsigned long			power_collapse_khz;
	unsigned long			wait_for_irq_khz;
};

static struct clk *ebi1_clk;
static struct clock_state drv_state = { 0 };

static void __init acpuclk_init(void);

/* MSM7201A Levels 3-6 all correspond to 1.2V, level 7 corresponds to 1.325V. */
enum {
	VDD_0 = 0,
	VDD_1 = 1,
	VDD_2 = 2,
	VDD_3 = 3,
	VDD_4 = 3,
	VDD_5 = 3,
	VDD_6 = 3,
	VDD_7 = 7,
	VDD_END
};

struct clkctl_acpu_speed {
	unsigned int	a11clk_khz;
	int		pll;
	unsigned int	a11clk_src_sel;
	unsigned int	a11clk_src_div;
	unsigned int	ahbclk_khz;
	unsigned int	ahbclk_div;
	int		vdd;
	unsigned int 	axiclk_khz;
	unsigned long	lpj; /* loops_per_jiffy */
/* Index in acpu_freq_tbl[] for steppings. */
	short		down;
	short		up;
};

/*
 * ACPU speed table. Complete table is shown but certain speeds are commented
 * out to optimized speed switching. Initalize loops_per_jiffy to 0.
 *
 * Table stepping up/down is optimized for 256mhz jumps while staying on the
 * same PLL.
 */
#if (0)
static struct clkctl_acpu_speed  acpu_freq_tbl[] = {
	{ 19200, ACPU_PLL_TCXO, 0, 0, 19200, 0, VDD_0, 30720, 0, 0, 8 },
	{ 61440, ACPU_PLL_0,  4, 3, 61440,  0, VDD_0, 30720,  0, 0, 8 },
	{ 81920, ACPU_PLL_0,  4, 2, 40960,  1, VDD_0, 61440,  0, 0, 8 },
	{ 96000, ACPU_PLL_1,  1, 7, 48000,  1, VDD_0, 61440,  0, 0, 9 },
	{ 122880, ACPU_PLL_0, 4, 1, 61440,  1, VDD_3, 61440,  0, 0, 8 },
	{ 128000, ACPU_PLL_1, 1, 5, 64000,  1, VDD_3, 61440,  0, 0, 12 },
	{ 176000, ACPU_PLL_2, 2, 5, 88000,  1, VDD_3, 61440,  0, 0, 11 },
	{ 192000, ACPU_PLL_1, 1, 3, 64000,  2, VDD_3, 61440,  0, 0, 12 },
	{ 245760, ACPU_PLL_0, 4, 0, 81920,  2, VDD_4, 61440,  0, 0, 12 },
	{ 256000, ACPU_PLL_1, 1, 2, 128000, 2, VDD_5, 128000, 0, 0, 12 },
	{ 264000, ACPU_PLL_2, 2, 3, 88000,  2, VDD_5, 128000, 0, 6, 13 },
	{ 352000, ACPU_PLL_2, 2, 2, 88000,  3, VDD_5, 128000, 0, 6, 13 },
	{ 384000, ACPU_PLL_1, 1, 1, 128000, 2, VDD_6, 128000, 0, 5, -1 },
	{ 528000, ACPU_PLL_2, 2, 1, 132000, 3, VDD_7, 128000, 0, 11, -1 },
	{ 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 },
};
#else /* Table of freq we currently use. */
static struct clkctl_acpu_speed  acpu_freq_tbl[] = {
	{ 19200, ACPU_PLL_TCXO, 0, 0, 19200, 0, VDD_0, 30720, 0, 0, 4 },
	{ 122880, ACPU_PLL_0, 4, 1, 61440, 1, VDD_3, 61440, 0, 0, 4 },
	{ 128000, ACPU_PLL_1, 1, 5, 64000, 1, VDD_3, 61440, 0, 0, 6 },
	{ 176000, ACPU_PLL_2, 2, 5, 88000, 1, VDD_3, 61440, 0, 0, 5 },
	{ 245760, ACPU_PLL_0, 4, 0, 81920, 2, VDD_4, 61440, 0, 0, 5 },
	{ 352000, ACPU_PLL_2, 2, 2, 88000, 3, VDD_5, 128000, 0, 3, 7 },
	{ 384000, ACPU_PLL_1, 1, 1, 128000, 2, VDD_6, 128000, 0, 2, -1 },
	{ 528000, ACPU_PLL_2, 2, 1, 132000, 3, VDD_7, 128000, 0, 5, -1 },
	{ 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 },
};
#endif

static struct cpufreq_frequency_table freq_table[] = {
	{ 0, 122880 },
	{ 1, 128000 },
	{ 2, 245760 },
	{ 3, 384000 },
	{ 4, 528000 },
	{ 5, CPUFREQ_TABLE_END },
};

static int pc_pll_request(unsigned id, unsigned on)
{
	int res;
	on = !!on;

#if PERF_SWITCH_DEBUG
	if (on)
		printk(KERN_DEBUG "Enabling PLL %d\n", id);
	else
		printk(KERN_DEBUG "Disabling PLL %d\n", id);
#endif

	res = msm_proc_comm(PCOM_CLKCTL_RPC_PLL_REQUEST, &id, &on);
	if (res < 0)
		return res;

#if PERF_SWITCH_DEBUG
	if (on)
		printk(KERN_DEBUG "PLL %d enabled\n", id);
	else
		printk(KERN_DEBUG "PLL %d disabled\n", id);
#endif
	return res;
}


/*----------------------------------------------------------------------------
 * ARM11 'owned' clock control
 *---------------------------------------------------------------------------*/

unsigned long acpuclk_power_collapse(void) {
	int ret = acpuclk_get_rate();
	ret *= 1000;
	if (ret > drv_state.power_collapse_khz)
		acpuclk_set_rate(drv_state.power_collapse_khz, 1);
	return ret;
}

unsigned long acpuclk_get_wfi_rate(void)
{
	return drv_state.wait_for_irq_khz;
}

unsigned long acpuclk_wait_for_irq(void) {
	int ret = acpuclk_get_rate();
	ret *= 1000;
	if (ret > drv_state.wait_for_irq_khz)
		acpuclk_set_rate(drv_state.wait_for_irq_khz, 1);
	return ret;
}

static int acpuclk_set_vdd_level(int vdd)
{
	uint32_t current_vdd;

	current_vdd = readl(A11S_VDD_SVS_PLEVEL_ADDR) & 0x07;

#if PERF_SWITCH_DEBUG
	printk(KERN_DEBUG "acpuclock: Switching VDD from %u -> %d\n",
	       current_vdd, vdd);
#endif
	writel((1 << 7) | (vdd << 3), A11S_VDD_SVS_PLEVEL_ADDR);
	udelay(drv_state.vdd_switch_time_us);
	if ((readl(A11S_VDD_SVS_PLEVEL_ADDR) & 0x7) != vdd) {
#if PERF_SWITCH_DEBUG
		printk(KERN_ERR "acpuclock: VDD set failed\n");
#endif
		return -EIO;
	}

#if PERF_SWITCH_DEBUG
	printk(KERN_DEBUG "acpuclock: VDD switched\n");
#endif
	return 0;
}

/* Set proper dividers for the given clock speed. */
static void acpuclk_set_div(const struct clkctl_acpu_speed *hunt_s) {
	uint32_t reg_clkctl, reg_clksel, clk_div;

	/* AHB_CLK_DIV */
	clk_div = (readl(A11S_CLK_SEL_ADDR) >> 1) & 0x03;
	/*
	 * If the new clock divider is higher than the previous, then
	 * program the divider before switching the clock
	 */
	if (hunt_s->ahbclk_div > clk_div) {
		reg_clksel = readl(A11S_CLK_SEL_ADDR);
		reg_clksel &= ~(0x3 << 1);
		reg_clksel |= (hunt_s->ahbclk_div << 1);
		writel(reg_clksel, A11S_CLK_SEL_ADDR);
	}
	if ((readl(A11S_CLK_SEL_ADDR) & 0x01) == 0) {
		/* SRC0 */

		/* Program clock source */
		reg_clkctl = readl(A11S_CLK_CNTL_ADDR);
		reg_clkctl &= ~(0x07 << 4);
		reg_clkctl |= (hunt_s->a11clk_src_sel << 4);
		writel(reg_clkctl, A11S_CLK_CNTL_ADDR);

		/* Program clock divider */
		reg_clkctl = readl(A11S_CLK_CNTL_ADDR);
		reg_clkctl &= ~0xf;
		reg_clkctl |= hunt_s->a11clk_src_div;
		writel(reg_clkctl, A11S_CLK_CNTL_ADDR);

		/* Program clock source selection */
		reg_clksel = readl(A11S_CLK_SEL_ADDR);
		reg_clksel |= 1; /* CLK_SEL_SRC1NO  == SRC1 */
		writel(reg_clksel, A11S_CLK_SEL_ADDR);
	} else {
		/* SRC1 */

		/* Program clock source */
		reg_clkctl = readl(A11S_CLK_CNTL_ADDR);
		reg_clkctl &= ~(0x07 << 12);
		reg_clkctl |= (hunt_s->a11clk_src_sel << 12);
		writel(reg_clkctl, A11S_CLK_CNTL_ADDR);

		/* Program clock divider */
		reg_clkctl = readl(A11S_CLK_CNTL_ADDR);
		reg_clkctl &= ~(0xf << 8);
		reg_clkctl |= (hunt_s->a11clk_src_div << 8);
		writel(reg_clkctl, A11S_CLK_CNTL_ADDR);

		/* Program clock source selection */
		reg_clksel = readl(A11S_CLK_SEL_ADDR);
		reg_clksel &= ~1; /* CLK_SEL_SRC1NO  == SRC0 */
		writel(reg_clksel, A11S_CLK_SEL_ADDR);
	}

	/*
	 * If the new clock divider is lower than the previous, then
	 * program the divider after switching the clock
	 */
	if (hunt_s->ahbclk_div < clk_div) {
		reg_clksel = readl(A11S_CLK_SEL_ADDR);
		reg_clksel &= ~(0x3 << 1);
		reg_clksel |= (hunt_s->ahbclk_div << 1);
		writel(reg_clksel, A11S_CLK_SEL_ADDR);
	}
}

int acpuclk_set_rate(unsigned long rate, int for_power_collapse)
{
	uint32_t reg_clkctl;
	struct clkctl_acpu_speed *cur_s, *tgt_s, *strt_s;
	int rc = 0;
	unsigned int plls_enabled = 0, pll;

	strt_s = cur_s = drv_state.current_speed;

	WARN_ONCE(cur_s == NULL, "acpuclk_set_rate: not initialized\n");
	if (cur_s == NULL)
		return -ENOENT;

	if (rate == (cur_s->a11clk_khz * 1000))
		return 0;

	for (tgt_s = acpu_freq_tbl; tgt_s->a11clk_khz != 0; tgt_s++) {
		if (tgt_s->a11clk_khz == (rate / 1000))
			break;
	}

	if (tgt_s->a11clk_khz == 0)
		return -EINVAL;

	/* Choose the highest speed speed at or below 'rate' with same PLL. */
	if (for_power_collapse && tgt_s->a11clk_khz < cur_s->a11clk_khz) {
		while (tgt_s->pll != ACPU_PLL_TCXO && tgt_s->pll != cur_s->pll)
			tgt_s--;
	}

	if (strt_s->pll != ACPU_PLL_TCXO)
		plls_enabled |= 1 << strt_s->pll;

	if (!for_power_collapse) {
		mutex_lock(&drv_state.lock);
		if (strt_s->pll != tgt_s->pll && tgt_s->pll != ACPU_PLL_TCXO) {
			rc = pc_pll_request(tgt_s->pll, 1);
			if (rc < 0) {
				pr_err("PLL%d enable failed (%d)\n",
					tgt_s->pll, rc);
				goto out;
			}
			plls_enabled |= 1 << tgt_s->pll;
		}
		/* Increase VDD if needed. */
		if (tgt_s->vdd > cur_s->vdd) {
			if ((rc = acpuclk_set_vdd_level(tgt_s->vdd)) < 0) {
				printk(KERN_ERR "Unable to switch ACPU vdd\n");
				goto out;
			}
		}
	}

	/* Set wait states for CPU inbetween frequency changes */
	reg_clkctl = readl(A11S_CLK_CNTL_ADDR);
	reg_clkctl |= (100 << 16); /* set WT_ST_CNT */
	writel(reg_clkctl, A11S_CLK_CNTL_ADDR);

#if PERF_SWITCH_DEBUG
	printk(KERN_INFO "acpuclock: Switching from ACPU rate %u -> %u\n",
	       strt_s->a11clk_khz * 1000, tgt_s->a11clk_khz * 1000);
#endif

	while (cur_s != tgt_s) {
		/*
		 * Always jump to target freq if within 256mhz, regulardless of
		 * PLL. If differnece is greater, use the predefinied
		 * steppings in the table.
		 */
		int d = abs((int)(cur_s->a11clk_khz - tgt_s->a11clk_khz));
		if (d > drv_state.max_speed_delta_khz) {
			/* Step up or down depending on target vs current. */
			int clk_index = tgt_s->a11clk_khz > cur_s->a11clk_khz ?
				cur_s->up : cur_s->down;
			if (clk_index < 0) { /* This should not happen. */
				printk(KERN_ERR "cur:%u target: %u\n",
					cur_s->a11clk_khz, tgt_s->a11clk_khz);
				rc = -EINVAL;
				goto out;
			}
			cur_s = &acpu_freq_tbl[clk_index];
		} else {
			cur_s = tgt_s;
		}
#if PERF_SWITCH_STEP_DEBUG
		printk(KERN_DEBUG "%s: STEP khz = %u, pll = %d\n",
			__FUNCTION__, cur_s->a11clk_khz, cur_s->pll);
#endif
		if (!for_power_collapse&& cur_s->pll != ACPU_PLL_TCXO
		    && !(plls_enabled & (1 << cur_s->pll))) {
			rc = pc_pll_request(cur_s->pll, 1);
			if (rc < 0) {
				pr_err("PLL%d enable failed (%d)\n",
					cur_s->pll, rc);
				goto out;
			}
			plls_enabled |= 1 << cur_s->pll;
		}

		acpuclk_set_div(cur_s);
		drv_state.current_speed = cur_s;
		/* Re-adjust lpj for the new clock speed. */
		loops_per_jiffy = cur_s->lpj;
		udelay(drv_state.acpu_switch_time_us);
	}

	/* Nothing else to do for power collapse. */
	if (for_power_collapse)
		return 0;

	/* Disable PLLs we are not using anymore. */
	plls_enabled &= ~(1 << tgt_s->pll);
	for (pll = ACPU_PLL_0; pll <= ACPU_PLL_2; pll++)
		if (plls_enabled & (1 << pll)) {
			rc = pc_pll_request(pll, 0);
			if (rc < 0) {
				pr_err("PLL%d disable failed (%d)\n", pll, rc);
				goto out;
			}
		}

	/* Change the AXI bus frequency if we can. */
	if (strt_s->axiclk_khz != tgt_s->axiclk_khz) {
		rc = clk_set_rate(ebi1_clk, tgt_s->axiclk_khz * 1000);
		if (rc < 0)
			pr_err("Setting AXI min rate failed!\n");
	}

	/* Drop VDD level if we can. */
	if (tgt_s->vdd < strt_s->vdd) {
		if (acpuclk_set_vdd_level(tgt_s->vdd) < 0)
			printk(KERN_ERR "acpuclock: Unable to drop ACPU vdd\n");
	}

#if PERF_SWITCH_DEBUG
	printk(KERN_DEBUG "%s: ACPU speed change complete\n", __FUNCTION__);
#endif
out:
	if (!for_power_collapse)
		mutex_unlock(&drv_state.lock);
	return rc;
}

static void __init acpuclk_init(void)
{
	struct clkctl_acpu_speed *speed;
	uint32_t div, sel;
	int rc;

	/*
	 * Determine the rate of ACPU clock
	 */

	if (!(readl(A11S_CLK_SEL_ADDR) & 0x01)) { /* CLK_SEL_SRC1N0 */
		/* CLK_SRC0_SEL */
		sel = (readl(A11S_CLK_CNTL_ADDR) >> 12) & 0x7;
		/* CLK_SRC0_DIV */
		div = (readl(A11S_CLK_CNTL_ADDR) >> 8) & 0x0f;
	} else {
		/* CLK_SRC1_SEL */
		sel = (readl(A11S_CLK_CNTL_ADDR) >> 4) & 0x07;
		/* CLK_SRC1_DIV */
		div = readl(A11S_CLK_CNTL_ADDR) & 0x0f;
	}

	for (speed = acpu_freq_tbl; speed->a11clk_khz != 0; speed++) {
		if (speed->a11clk_src_sel == sel
		 && (speed->a11clk_src_div == div))
			break;
	}
	if (speed->a11clk_khz == 0) {
		printk(KERN_WARNING "Warning - ACPU clock reports invalid speed\n");
		return;
	}

	drv_state.current_speed = speed;

	rc = clk_set_rate(ebi1_clk, speed->axiclk_khz * 1000);
	if (rc < 0)
		pr_err("Setting AXI min rate failed!\n");

	printk(KERN_INFO "ACPU running at %d KHz\n", speed->a11clk_khz);
}

unsigned long acpuclk_get_rate(void)
{
	WARN_ONCE(drv_state.current_speed == NULL,
		  "acpuclk_get_rate: not initialized\n");
	if (drv_state.current_speed)
		return drv_state.current_speed->a11clk_khz;
	else
		return 0;
}

uint32_t acpuclk_get_switch_time(void)
{
	return drv_state.acpu_switch_time_us;
}

/*----------------------------------------------------------------------------
 * Clock driver initialization
 *---------------------------------------------------------------------------*/

/* Initalize the lpj field in the acpu_freq_tbl. */
static void __init lpj_init(void)
{
	int i;
	const struct clkctl_acpu_speed *base_clk = drv_state.current_speed;
	for (i = 0; acpu_freq_tbl[i].a11clk_khz; i++) {
		acpu_freq_tbl[i].lpj = cpufreq_scale(loops_per_jiffy,
						base_clk->a11clk_khz,
						acpu_freq_tbl[i].a11clk_khz);
	}
}

void __init msm_acpu_clock_init(struct msm_acpu_clock_platform_data *clkdata)
{
	pr_info("acpu_clock_init()\n");

	ebi1_clk = clk_get(NULL, "ebi1_clk");

	mutex_init(&drv_state.lock);
	drv_state.acpu_switch_time_us = clkdata->acpu_switch_time_us;
	drv_state.max_speed_delta_khz = clkdata->max_speed_delta_khz;
	drv_state.vdd_switch_time_us = clkdata->vdd_switch_time_us;
	drv_state.power_collapse_khz = clkdata->power_collapse_khz;
	drv_state.wait_for_irq_khz = clkdata->wait_for_irq_khz;
	acpuclk_init();
	lpj_init();
#ifdef CONFIG_CPU_FREQ_TABLE
	cpufreq_frequency_table_get_attr(freq_table, smp_processor_id());
#endif
}