Guenter Roeck | d21ed22 | 2019-11-23 11:11:26 -0800 | [diff] [blame] | 1 | // SPDX-License-Identifier: GPL-2.0-or-later |
| 2 | /* |
| 3 | * Driver for MAX31730 3-Channel Remote Temperature Sensor |
| 4 | * |
| 5 | * Copyright (c) 2019 Guenter Roeck <linux@roeck-us.net> |
| 6 | */ |
| 7 | |
| 8 | #include <linux/bits.h> |
| 9 | #include <linux/err.h> |
| 10 | #include <linux/i2c.h> |
| 11 | #include <linux/init.h> |
| 12 | #include <linux/hwmon.h> |
| 13 | #include <linux/module.h> |
| 14 | #include <linux/of_device.h> |
| 15 | #include <linux/of.h> |
| 16 | #include <linux/slab.h> |
| 17 | |
| 18 | /* Addresses scanned */ |
| 19 | static const unsigned short normal_i2c[] = { 0x1c, 0x1d, 0x1e, 0x1f, 0x4c, |
| 20 | 0x4d, 0x4e, 0x4f, I2C_CLIENT_END }; |
| 21 | |
| 22 | /* The MAX31730 registers */ |
| 23 | #define MAX31730_REG_TEMP 0x00 |
| 24 | #define MAX31730_REG_CONF 0x13 |
| 25 | #define MAX31730_STOP BIT(7) |
| 26 | #define MAX31730_EXTRANGE BIT(1) |
| 27 | #define MAX31730_REG_TEMP_OFFSET 0x16 |
| 28 | #define MAX31730_TEMP_OFFSET_BASELINE 0x77 |
| 29 | #define MAX31730_REG_OFFSET_ENABLE 0x17 |
| 30 | #define MAX31730_REG_TEMP_MAX 0x20 |
| 31 | #define MAX31730_REG_TEMP_MIN 0x30 |
| 32 | #define MAX31730_REG_STATUS_HIGH 0x32 |
| 33 | #define MAX31730_REG_STATUS_LOW 0x33 |
| 34 | #define MAX31730_REG_CHANNEL_ENABLE 0x35 |
| 35 | #define MAX31730_REG_TEMP_FAULT 0x36 |
| 36 | |
| 37 | #define MAX31730_REG_MFG_ID 0x50 |
| 38 | #define MAX31730_MFG_ID 0x4d |
| 39 | #define MAX31730_REG_MFG_REV 0x51 |
| 40 | #define MAX31730_MFG_REV 0x01 |
| 41 | |
| 42 | #define MAX31730_TEMP_MIN (-128000) |
| 43 | #define MAX31730_TEMP_MAX 127937 |
| 44 | |
| 45 | /* Each client has this additional data */ |
| 46 | struct max31730_data { |
| 47 | struct i2c_client *client; |
| 48 | u8 orig_conf; |
| 49 | u8 current_conf; |
| 50 | u8 offset_enable; |
| 51 | u8 channel_enable; |
| 52 | }; |
| 53 | |
| 54 | /*-----------------------------------------------------------------------*/ |
| 55 | |
| 56 | static inline long max31730_reg_to_mc(s16 temp) |
| 57 | { |
| 58 | return DIV_ROUND_CLOSEST((temp >> 4) * 1000, 16); |
| 59 | } |
| 60 | |
| 61 | static int max31730_write_config(struct max31730_data *data, u8 set_mask, |
| 62 | u8 clr_mask) |
| 63 | { |
| 64 | u8 value; |
| 65 | |
| 66 | clr_mask |= MAX31730_EXTRANGE; |
| 67 | value = data->current_conf & ~clr_mask; |
| 68 | value |= set_mask; |
| 69 | |
| 70 | if (data->current_conf != value) { |
| 71 | s32 err; |
| 72 | |
| 73 | err = i2c_smbus_write_byte_data(data->client, MAX31730_REG_CONF, |
| 74 | value); |
| 75 | if (err) |
| 76 | return err; |
| 77 | data->current_conf = value; |
| 78 | } |
| 79 | return 0; |
| 80 | } |
| 81 | |
| 82 | static int max31730_set_enable(struct i2c_client *client, int reg, |
| 83 | u8 *confdata, int channel, bool enable) |
| 84 | { |
| 85 | u8 regval = *confdata; |
| 86 | int err; |
| 87 | |
| 88 | if (enable) |
| 89 | regval |= BIT(channel); |
| 90 | else |
| 91 | regval &= ~BIT(channel); |
| 92 | |
| 93 | if (regval != *confdata) { |
| 94 | err = i2c_smbus_write_byte_data(client, reg, regval); |
| 95 | if (err) |
| 96 | return err; |
| 97 | *confdata = regval; |
| 98 | } |
| 99 | return 0; |
| 100 | } |
| 101 | |
| 102 | static int max31730_set_offset_enable(struct max31730_data *data, int channel, |
| 103 | bool enable) |
| 104 | { |
| 105 | return max31730_set_enable(data->client, MAX31730_REG_OFFSET_ENABLE, |
| 106 | &data->offset_enable, channel, enable); |
| 107 | } |
| 108 | |
| 109 | static int max31730_set_channel_enable(struct max31730_data *data, int channel, |
| 110 | bool enable) |
| 111 | { |
| 112 | return max31730_set_enable(data->client, MAX31730_REG_CHANNEL_ENABLE, |
| 113 | &data->channel_enable, channel, enable); |
| 114 | } |
| 115 | |
| 116 | static int max31730_read(struct device *dev, enum hwmon_sensor_types type, |
| 117 | u32 attr, int channel, long *val) |
| 118 | { |
| 119 | struct max31730_data *data = dev_get_drvdata(dev); |
| 120 | int regval, reg, offset; |
| 121 | |
| 122 | if (type != hwmon_temp) |
| 123 | return -EINVAL; |
| 124 | |
| 125 | switch (attr) { |
| 126 | case hwmon_temp_input: |
| 127 | if (!(data->channel_enable & BIT(channel))) |
| 128 | return -ENODATA; |
| 129 | reg = MAX31730_REG_TEMP + (channel * 2); |
| 130 | break; |
| 131 | case hwmon_temp_max: |
| 132 | reg = MAX31730_REG_TEMP_MAX + (channel * 2); |
| 133 | break; |
| 134 | case hwmon_temp_min: |
| 135 | reg = MAX31730_REG_TEMP_MIN; |
| 136 | break; |
| 137 | case hwmon_temp_enable: |
| 138 | *val = !!(data->channel_enable & BIT(channel)); |
| 139 | return 0; |
| 140 | case hwmon_temp_offset: |
| 141 | if (!channel) |
| 142 | return -EINVAL; |
| 143 | if (!(data->offset_enable & BIT(channel))) { |
| 144 | *val = 0; |
| 145 | return 0; |
| 146 | } |
| 147 | offset = i2c_smbus_read_byte_data(data->client, |
| 148 | MAX31730_REG_TEMP_OFFSET); |
| 149 | if (offset < 0) |
| 150 | return offset; |
| 151 | *val = (offset - MAX31730_TEMP_OFFSET_BASELINE) * 125; |
| 152 | return 0; |
| 153 | case hwmon_temp_fault: |
| 154 | regval = i2c_smbus_read_byte_data(data->client, |
| 155 | MAX31730_REG_TEMP_FAULT); |
| 156 | if (regval < 0) |
| 157 | return regval; |
| 158 | *val = !!(regval & BIT(channel)); |
| 159 | return 0; |
| 160 | case hwmon_temp_min_alarm: |
| 161 | regval = i2c_smbus_read_byte_data(data->client, |
| 162 | MAX31730_REG_STATUS_LOW); |
| 163 | if (regval < 0) |
| 164 | return regval; |
| 165 | *val = !!(regval & BIT(channel)); |
| 166 | return 0; |
| 167 | case hwmon_temp_max_alarm: |
| 168 | regval = i2c_smbus_read_byte_data(data->client, |
| 169 | MAX31730_REG_STATUS_HIGH); |
| 170 | if (regval < 0) |
| 171 | return regval; |
| 172 | *val = !!(regval & BIT(channel)); |
| 173 | return 0; |
| 174 | default: |
| 175 | return -EINVAL; |
| 176 | } |
| 177 | regval = i2c_smbus_read_word_swapped(data->client, reg); |
| 178 | if (regval < 0) |
| 179 | return regval; |
| 180 | |
| 181 | *val = max31730_reg_to_mc(regval); |
| 182 | |
| 183 | return 0; |
| 184 | } |
| 185 | |
| 186 | static int max31730_write(struct device *dev, enum hwmon_sensor_types type, |
| 187 | u32 attr, int channel, long val) |
| 188 | { |
| 189 | struct max31730_data *data = dev_get_drvdata(dev); |
| 190 | int reg, err; |
| 191 | |
| 192 | if (type != hwmon_temp) |
| 193 | return -EINVAL; |
| 194 | |
| 195 | switch (attr) { |
| 196 | case hwmon_temp_max: |
| 197 | reg = MAX31730_REG_TEMP_MAX + channel * 2; |
| 198 | break; |
| 199 | case hwmon_temp_min: |
| 200 | reg = MAX31730_REG_TEMP_MIN; |
| 201 | break; |
| 202 | case hwmon_temp_enable: |
| 203 | if (val != 0 && val != 1) |
| 204 | return -EINVAL; |
| 205 | return max31730_set_channel_enable(data, channel, val); |
| 206 | case hwmon_temp_offset: |
| 207 | val = clamp_val(val, -14875, 17000) + 14875; |
| 208 | val = DIV_ROUND_CLOSEST(val, 125); |
| 209 | err = max31730_set_offset_enable(data, channel, |
| 210 | val != MAX31730_TEMP_OFFSET_BASELINE); |
| 211 | if (err) |
| 212 | return err; |
| 213 | return i2c_smbus_write_byte_data(data->client, |
| 214 | MAX31730_REG_TEMP_OFFSET, val); |
| 215 | default: |
| 216 | return -EINVAL; |
| 217 | } |
| 218 | |
| 219 | val = clamp_val(val, MAX31730_TEMP_MIN, MAX31730_TEMP_MAX); |
| 220 | val = DIV_ROUND_CLOSEST(val << 4, 1000) << 4; |
| 221 | |
| 222 | return i2c_smbus_write_word_swapped(data->client, reg, (u16)val); |
| 223 | } |
| 224 | |
| 225 | static umode_t max31730_is_visible(const void *data, |
| 226 | enum hwmon_sensor_types type, |
| 227 | u32 attr, int channel) |
| 228 | { |
| 229 | switch (type) { |
| 230 | case hwmon_temp: |
| 231 | switch (attr) { |
| 232 | case hwmon_temp_input: |
| 233 | case hwmon_temp_min_alarm: |
| 234 | case hwmon_temp_max_alarm: |
| 235 | case hwmon_temp_fault: |
| 236 | return 0444; |
| 237 | case hwmon_temp_min: |
| 238 | return channel ? 0444 : 0644; |
| 239 | case hwmon_temp_offset: |
| 240 | case hwmon_temp_enable: |
| 241 | case hwmon_temp_max: |
| 242 | return 0644; |
| 243 | } |
| 244 | break; |
| 245 | default: |
| 246 | break; |
| 247 | } |
| 248 | return 0; |
| 249 | } |
| 250 | |
| 251 | static const struct hwmon_channel_info *max31730_info[] = { |
| 252 | HWMON_CHANNEL_INFO(chip, |
| 253 | HWMON_C_REGISTER_TZ), |
| 254 | HWMON_CHANNEL_INFO(temp, |
| 255 | HWMON_T_INPUT | HWMON_T_MIN | HWMON_T_MAX | |
| 256 | HWMON_T_ENABLE | |
| 257 | HWMON_T_MIN_ALARM | HWMON_T_MAX_ALARM, |
| 258 | HWMON_T_INPUT | HWMON_T_MIN | HWMON_T_MAX | |
| 259 | HWMON_T_OFFSET | HWMON_T_ENABLE | |
| 260 | HWMON_T_MIN_ALARM | HWMON_T_MAX_ALARM | |
| 261 | HWMON_T_FAULT, |
| 262 | HWMON_T_INPUT | HWMON_T_MIN | HWMON_T_MAX | |
| 263 | HWMON_T_OFFSET | HWMON_T_ENABLE | |
| 264 | HWMON_T_MIN_ALARM | HWMON_T_MAX_ALARM | |
| 265 | HWMON_T_FAULT, |
| 266 | HWMON_T_INPUT | HWMON_T_MIN | HWMON_T_MAX | |
| 267 | HWMON_T_OFFSET | HWMON_T_ENABLE | |
| 268 | HWMON_T_MIN_ALARM | HWMON_T_MAX_ALARM | |
| 269 | HWMON_T_FAULT |
| 270 | ), |
| 271 | NULL |
| 272 | }; |
| 273 | |
| 274 | static const struct hwmon_ops max31730_hwmon_ops = { |
| 275 | .is_visible = max31730_is_visible, |
| 276 | .read = max31730_read, |
| 277 | .write = max31730_write, |
| 278 | }; |
| 279 | |
| 280 | static const struct hwmon_chip_info max31730_chip_info = { |
| 281 | .ops = &max31730_hwmon_ops, |
| 282 | .info = max31730_info, |
| 283 | }; |
| 284 | |
| 285 | static void max31730_remove(void *data) |
| 286 | { |
| 287 | struct max31730_data *max31730 = data; |
| 288 | struct i2c_client *client = max31730->client; |
| 289 | |
| 290 | i2c_smbus_write_byte_data(client, MAX31730_REG_CONF, |
| 291 | max31730->orig_conf); |
| 292 | } |
| 293 | |
| 294 | static int |
Stephen Kitt | 6748703 | 2020-08-13 18:02:22 +0200 | [diff] [blame] | 295 | max31730_probe(struct i2c_client *client) |
Guenter Roeck | d21ed22 | 2019-11-23 11:11:26 -0800 | [diff] [blame] | 296 | { |
| 297 | struct device *dev = &client->dev; |
| 298 | struct device *hwmon_dev; |
| 299 | struct max31730_data *data; |
| 300 | int status, err; |
| 301 | |
| 302 | if (!i2c_check_functionality(client->adapter, |
| 303 | I2C_FUNC_SMBUS_BYTE_DATA | I2C_FUNC_SMBUS_WORD_DATA)) |
| 304 | return -EIO; |
| 305 | |
| 306 | data = devm_kzalloc(dev, sizeof(struct max31730_data), GFP_KERNEL); |
| 307 | if (!data) |
| 308 | return -ENOMEM; |
| 309 | |
| 310 | data->client = client; |
| 311 | |
| 312 | /* Cache original configuration and enable status */ |
| 313 | status = i2c_smbus_read_byte_data(client, MAX31730_REG_CHANNEL_ENABLE); |
| 314 | if (status < 0) |
| 315 | return status; |
| 316 | data->channel_enable = status; |
| 317 | |
| 318 | status = i2c_smbus_read_byte_data(client, MAX31730_REG_OFFSET_ENABLE); |
| 319 | if (status < 0) |
| 320 | return status; |
| 321 | data->offset_enable = status; |
| 322 | |
| 323 | status = i2c_smbus_read_byte_data(client, MAX31730_REG_CONF); |
| 324 | if (status < 0) |
| 325 | return status; |
| 326 | data->orig_conf = status; |
| 327 | data->current_conf = status; |
| 328 | |
| 329 | err = max31730_write_config(data, |
| 330 | data->channel_enable ? 0 : MAX31730_STOP, |
| 331 | data->channel_enable ? MAX31730_STOP : 0); |
| 332 | if (err) |
| 333 | return err; |
| 334 | |
| 335 | dev_set_drvdata(dev, data); |
| 336 | |
| 337 | err = devm_add_action_or_reset(dev, max31730_remove, data); |
| 338 | if (err) |
| 339 | return err; |
| 340 | |
| 341 | hwmon_dev = devm_hwmon_device_register_with_info(dev, client->name, |
| 342 | data, |
| 343 | &max31730_chip_info, |
| 344 | NULL); |
| 345 | return PTR_ERR_OR_ZERO(hwmon_dev); |
| 346 | } |
| 347 | |
| 348 | static const struct i2c_device_id max31730_ids[] = { |
| 349 | { "max31730", 0, }, |
| 350 | { } |
| 351 | }; |
| 352 | MODULE_DEVICE_TABLE(i2c, max31730_ids); |
| 353 | |
| 354 | static const struct of_device_id __maybe_unused max31730_of_match[] = { |
| 355 | { |
| 356 | .compatible = "maxim,max31730", |
| 357 | }, |
| 358 | { }, |
| 359 | }; |
| 360 | MODULE_DEVICE_TABLE(of, max31730_of_match); |
| 361 | |
| 362 | static bool max31730_check_reg_temp(struct i2c_client *client, |
| 363 | int reg) |
| 364 | { |
| 365 | int regval; |
| 366 | |
| 367 | regval = i2c_smbus_read_byte_data(client, reg + 1); |
| 368 | return regval < 0 || (regval & 0x0f); |
| 369 | } |
| 370 | |
| 371 | /* Return 0 if detection is successful, -ENODEV otherwise */ |
| 372 | static int max31730_detect(struct i2c_client *client, |
| 373 | struct i2c_board_info *info) |
| 374 | { |
| 375 | struct i2c_adapter *adapter = client->adapter; |
| 376 | int regval; |
| 377 | int i; |
| 378 | |
| 379 | if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA | |
| 380 | I2C_FUNC_SMBUS_WORD_DATA)) |
| 381 | return -ENODEV; |
| 382 | |
| 383 | regval = i2c_smbus_read_byte_data(client, MAX31730_REG_MFG_ID); |
| 384 | if (regval != MAX31730_MFG_ID) |
| 385 | return -ENODEV; |
| 386 | regval = i2c_smbus_read_byte_data(client, MAX31730_REG_MFG_REV); |
| 387 | if (regval != MAX31730_MFG_REV) |
| 388 | return -ENODEV; |
| 389 | |
| 390 | /* lower 4 bit of temperature and limit registers must be 0 */ |
| 391 | if (max31730_check_reg_temp(client, MAX31730_REG_TEMP_MIN)) |
| 392 | return -ENODEV; |
| 393 | |
| 394 | for (i = 0; i < 4; i++) { |
| 395 | if (max31730_check_reg_temp(client, MAX31730_REG_TEMP + i * 2)) |
| 396 | return -ENODEV; |
| 397 | if (max31730_check_reg_temp(client, |
| 398 | MAX31730_REG_TEMP_MAX + i * 2)) |
| 399 | return -ENODEV; |
| 400 | } |
| 401 | |
| 402 | strlcpy(info->type, "max31730", I2C_NAME_SIZE); |
| 403 | |
| 404 | return 0; |
| 405 | } |
| 406 | |
| 407 | static int __maybe_unused max31730_suspend(struct device *dev) |
| 408 | { |
| 409 | struct max31730_data *data = dev_get_drvdata(dev); |
| 410 | |
| 411 | return max31730_write_config(data, MAX31730_STOP, 0); |
| 412 | } |
| 413 | |
| 414 | static int __maybe_unused max31730_resume(struct device *dev) |
| 415 | { |
| 416 | struct max31730_data *data = dev_get_drvdata(dev); |
| 417 | |
| 418 | return max31730_write_config(data, 0, MAX31730_STOP); |
| 419 | } |
| 420 | |
| 421 | static SIMPLE_DEV_PM_OPS(max31730_pm_ops, max31730_suspend, max31730_resume); |
| 422 | |
| 423 | static struct i2c_driver max31730_driver = { |
| 424 | .class = I2C_CLASS_HWMON, |
| 425 | .driver = { |
| 426 | .name = "max31730", |
| 427 | .of_match_table = of_match_ptr(max31730_of_match), |
| 428 | .pm = &max31730_pm_ops, |
| 429 | }, |
Stephen Kitt | 6748703 | 2020-08-13 18:02:22 +0200 | [diff] [blame] | 430 | .probe_new = max31730_probe, |
Guenter Roeck | d21ed22 | 2019-11-23 11:11:26 -0800 | [diff] [blame] | 431 | .id_table = max31730_ids, |
| 432 | .detect = max31730_detect, |
| 433 | .address_list = normal_i2c, |
| 434 | }; |
| 435 | |
| 436 | module_i2c_driver(max31730_driver); |
| 437 | |
| 438 | MODULE_AUTHOR("Guenter Roeck <linux@roeck-us.net>"); |
| 439 | MODULE_DESCRIPTION("MAX31730 driver"); |
| 440 | MODULE_LICENSE("GPL"); |