arch/arm/mach-shmobile/board-mackerel.c

/*
 * mackerel board support
 *
 * Copyright (C) 2010 Renesas Solutions Corp.
 * Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
 *
 * based on ap4evb
 * Copyright (C) 2010  Magnus Damm
 * Copyright (C) 2008  Yoshihiro Shimoda
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
 * the Free Software Foundation; version 2 of the License.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program; if not, write to the Free Software
 * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301  USA
 */
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/interrupt.h>
#include <linux/irq.h>
#include <linux/platform_device.h>
#include <linux/gpio.h>
#include <linux/input.h>
#include <linux/io.h>
#include <linux/mtd/mtd.h>
#include <linux/mtd/partitions.h>
#include <linux/mtd/physmap.h>
#include <linux/smsc911x.h>
#include <linux/usb/r8a66597.h>

#include <video/sh_mobile_lcdc.h>

#include <mach/common.h>
#include <mach/sh7372.h>

#include <asm/mach/arch.h>
#include <asm/mach/time.h>
#include <asm/mach/map.h>
#include <asm/mach-types.h>

/*
 * Address	Interface		BusWidth	note
 * ------------------------------------------------------------------
 * 0x0000_0000	NOR Flash ROM (MCP)	16bit		SW7 : bit1 = ON
 * 0x0800_0000	user area		-
 * 0x1000_0000	NOR Flash ROM (MCP)	16bit		SW7 : bit1 = OFF
 * 0x1400_0000	Ether (LAN9220)		16bit
 * 0x1600_0000	user area		-		cannot use with NAND
 * 0x1800_0000	user area		-
 * 0x1A00_0000	-
 * 0x4000_0000	LPDDR2-SDRAM (POP)	32bit
 */

/*
 * CPU mode
 *
 * SW4                                     | Boot Area| Master   | Remarks
 *  1  | 2   | 3   | 4   | 5   | 6   | 8   |          | Processor|
 * ----+-----+-----+-----+-----+-----+-----+----------+----------+--------------
 * ON  | ON  | OFF | ON  | ON  | OFF | OFF | External | System   | External ROM
 * ON  | ON  | ON  | ON  | ON  | OFF | OFF | External | System   | ROM Debug
 * ON  | ON  | X   | ON  | OFF | OFF | OFF | Built-in | System   | ROM Debug
 * X   | OFF | X   | X   | X   | X   | OFF | Built-in | System   | MaskROM
 * OFF | X   | X   | X   | X   | X   | OFF | Built-in | System   | MaskROM
 * X   | X   | X   | OFF | X   | X   | OFF | Built-in | System   | MaskROM
 * OFF | ON  | OFF | X   | X   | OFF | ON  | External | System   | Standalone
 * ON  | OFF | OFF | X   | X   | OFF | ON  | External | Realtime | Standalone
*/

/*
 * NOR Flash ROM
 *
 *  SW1  |     SW2    | SW7  | NOR Flash ROM
 *  bit1 | bit1  bit2 | bit1 | Memory allocation
 * ------+------------+------+------------------
 *  OFF  | ON     OFF | ON   |    Area 0
 *  OFF  | ON     OFF | OFF  |    Area 4
 */

/*
 * SMSC 9220
 *
 *  SW1		SMSC 9220
 * -----------------------
 *  ON		access disable
 *  OFF		access enable
 */

/*
 * NAND Flash ROM
 *
 *  SW1  |     SW2    | SW7  | NAND Flash ROM
 *  bit1 | bit1  bit2 | bit2 | Memory allocation
 * ------+------------+------+------------------
 *  OFF  | ON     OFF | ON   |    FCE 0
 *  OFF  | ON     OFF | OFF  |    FCE 1
 */

/*
 * External interrupt pin settings
 *
 * IRQX  | pin setting        | device             | level
 * ------+--------------------+--------------------+-------
 * IRQ0  | ICR1A.IRQ0SA=0010  | SDHI2 card detect  | Low
 * IRQ6  | ICR1A.IRQ6SA=0011  | Ether(LAN9220)     | High
 * IRQ7  | ICR1A.IRQ7SA=0010  | LCD Tuch Panel     | Low
 * IRQ8  | ICR2A.IRQ8SA=0010  | MMC/SD card detect | Low
 * IRQ9  | ICR2A.IRQ9SA=0010  | KEY(TCA6408)       | Low
 * IRQ21 | ICR4A.IRQ21SA=0011 | Sensor(ADXL345)    | High
 * IRQ22 | ICR4A.IRQ22SA=0011 | Sensor(AK8975)     | High
 */

/*
 * USB
 *
 * USB0 : CN22 : Function
 * USB1 : CN31 : Function/Host *1
 *
 * J30 (for CN31) *1
 * ----------+---------------+-------------
 * 1-2 short | VBUS 5V       | Host
 * open      | external VBUS | Function
 *
 * *1
 * CN31 is used as Host in Linux.
 */

/* MTD */
static struct mtd_partition nor_flash_partitions[] = {
	{
		.name		= "loader",
		.offset		= 0x00000000,
		.size		= 512 * 1024,
		.mask_flags	= MTD_WRITEABLE,
	},
	{
		.name		= "bootenv",
		.offset		= MTDPART_OFS_APPEND,
		.size		= 512 * 1024,
		.mask_flags	= MTD_WRITEABLE,
	},
	{
		.name		= "kernel_ro",
		.offset		= MTDPART_OFS_APPEND,
		.size		= 8 * 1024 * 1024,
		.mask_flags	= MTD_WRITEABLE,
	},
	{
		.name		= "kernel",
		.offset		= MTDPART_OFS_APPEND,
		.size		= 8 * 1024 * 1024,
	},
	{
		.name		= "data",
		.offset		= MTDPART_OFS_APPEND,
		.size		= MTDPART_SIZ_FULL,
	},
};

static struct physmap_flash_data nor_flash_data = {
	.width		= 2,
	.parts		= nor_flash_partitions,
	.nr_parts	= ARRAY_SIZE(nor_flash_partitions),
};

static struct resource nor_flash_resources[] = {
	[0]	= {
		.start	= 0x00000000,
		.end	= 0x08000000 - 1,
		.flags	= IORESOURCE_MEM,
	}
};

static struct platform_device nor_flash_device = {
	.name		= "physmap-flash",
	.dev		= {
		.platform_data	= &nor_flash_data,
	},
	.num_resources	= ARRAY_SIZE(nor_flash_resources),
	.resource	= nor_flash_resources,
};

/* SMSC */
static struct resource smc911x_resources[] = {
	{
		.start	= 0x14000000,
		.end	= 0x16000000 - 1,
		.flags	= IORESOURCE_MEM,
	}, {
		.start	= evt2irq(0x02c0) /* IRQ6A */,
		.flags	= IORESOURCE_IRQ | IORESOURCE_IRQ_LOWLEVEL,
	},
};

static struct smsc911x_platform_config smsc911x_info = {
	.flags		= SMSC911X_USE_16BIT | SMSC911X_SAVE_MAC_ADDRESS,
	.irq_polarity   = SMSC911X_IRQ_POLARITY_ACTIVE_LOW,
	.irq_type       = SMSC911X_IRQ_TYPE_PUSH_PULL,
};

static struct platform_device smc911x_device = {
	.name           = "smsc911x",
	.id             = -1,
	.num_resources  = ARRAY_SIZE(smc911x_resources),
	.resource       = smc911x_resources,
	.dev            = {
		.platform_data = &smsc911x_info,
	},
};

/* LCDC */
static struct fb_videomode mackerel_lcdc_modes[] = {
	{
		.name		= "WVGA Panel",
		.xres		= 800,
		.yres		= 480,
		.left_margin	= 220,
		.right_margin	= 110,
		.hsync_len	= 70,
		.upper_margin	= 20,
		.lower_margin	= 5,
		.vsync_len	= 5,
		.sync		= 0,
	},
};

static struct sh_mobile_lcdc_info lcdc_info = {
	.clock_source = LCDC_CLK_BUS,
	.ch[0] = {
		.chan = LCDC_CHAN_MAINLCD,
		.bpp = 16,
		.lcd_cfg = mackerel_lcdc_modes,
		.num_cfg = ARRAY_SIZE(mackerel_lcdc_modes),
		.interface_type		= RGB24,
		.clock_divider		= 2,
		.flags			= 0,
		.lcd_size_cfg.width	= 152,
		.lcd_size_cfg.height	= 91,
	}
};

static struct resource lcdc_resources[] = {
	[0] = {
		.name	= "LCDC",
		.start	= 0xfe940000,
		.end	= 0xfe943fff,
		.flags	= IORESOURCE_MEM,
	},
	[1] = {
		.start	= intcs_evt2irq(0x580),
		.flags	= IORESOURCE_IRQ,
	},
};

static struct platform_device lcdc_device = {
	.name		= "sh_mobile_lcdc_fb",
	.num_resources	= ARRAY_SIZE(lcdc_resources),
	.resource	= lcdc_resources,
	.dev	= {
		.platform_data	= &lcdc_info,
		.coherent_dma_mask = ~0,
	},
};

/* USB1 (Host) */
static void usb1_host_port_power(int port, int power)
{
	if (!power) /* only power-on is supported for now */
		return;

	/* set VBOUT/PWEN and EXTLP1 in DVSTCTR */
	__raw_writew(__raw_readw(0xE68B0008) | 0x600, 0xE68B0008);
}

static struct r8a66597_platdata usb1_host_data = {
	.on_chip	= 1,
	.port_power	= usb1_host_port_power,
};

static struct resource usb1_host_resources[] = {
	[0] = {
		.name	= "USBHS",
		.start	= 0xE68B0000,
		.end	= 0xE68B00E6 - 1,
		.flags	= IORESOURCE_MEM,
	},
	[1] = {
		.start	= evt2irq(0x1ce0) /* USB1_USB1I0 */,
		.flags	= IORESOURCE_IRQ,
	},
};

static struct platform_device usb1_host_device = {
	.name	= "r8a66597_hcd",
	.id	= 1,
	.dev = {
		.dma_mask		= NULL,         /*  not use dma */
		.coherent_dma_mask	= 0xffffffff,
		.platform_data		= &usb1_host_data,
	},
	.num_resources	= ARRAY_SIZE(usb1_host_resources),
	.resource	= usb1_host_resources,
};

static struct platform_device *mackerel_devices[] __initdata = {
	&nor_flash_device,
	&smc911x_device,
	&lcdc_device,
	&usb1_host_device,
};

static struct map_desc mackerel_io_desc[] __initdata = {
	/* create a 1:1 entity map for 0xe6xxxxxx
	 * used by CPGA, INTC and PFC.
	 */
	{
		.virtual	= 0xe6000000,
		.pfn		= __phys_to_pfn(0xe6000000),
		.length		= 256 << 20,
		.type		= MT_DEVICE_NONSHARED
	},
};

static void __init mackerel_map_io(void)
{
	iotable_init(mackerel_io_desc, ARRAY_SIZE(mackerel_io_desc));

	/* setup early devices and console here as well */
	sh7372_add_early_devices();
	shmobile_setup_console();
}

static void __init mackerel_init(void)
{
	sh7372_pinmux_init();

	/* enable SCIFA0 */
	gpio_request(GPIO_FN_SCIFA0_TXD, NULL);
	gpio_request(GPIO_FN_SCIFA0_RXD, NULL);

	/* enable SMSC911X */
	gpio_request(GPIO_FN_CS5A,	NULL);
	gpio_request(GPIO_FN_IRQ6_39,	NULL);

	/* LCDC */
	gpio_request(GPIO_FN_LCDD23,   NULL);
	gpio_request(GPIO_FN_LCDD22,   NULL);
	gpio_request(GPIO_FN_LCDD21,   NULL);
	gpio_request(GPIO_FN_LCDD20,   NULL);
	gpio_request(GPIO_FN_LCDD19,   NULL);
	gpio_request(GPIO_FN_LCDD18,   NULL);
	gpio_request(GPIO_FN_LCDD17,   NULL);
	gpio_request(GPIO_FN_LCDD16,   NULL);
	gpio_request(GPIO_FN_LCDD15,   NULL);
	gpio_request(GPIO_FN_LCDD14,   NULL);
	gpio_request(GPIO_FN_LCDD13,   NULL);
	gpio_request(GPIO_FN_LCDD12,   NULL);
	gpio_request(GPIO_FN_LCDD11,   NULL);
	gpio_request(GPIO_FN_LCDD10,   NULL);
	gpio_request(GPIO_FN_LCDD9,    NULL);
	gpio_request(GPIO_FN_LCDD8,    NULL);
	gpio_request(GPIO_FN_LCDD7,    NULL);
	gpio_request(GPIO_FN_LCDD6,    NULL);
	gpio_request(GPIO_FN_LCDD5,    NULL);
	gpio_request(GPIO_FN_LCDD4,    NULL);
	gpio_request(GPIO_FN_LCDD3,    NULL);
	gpio_request(GPIO_FN_LCDD2,    NULL);
	gpio_request(GPIO_FN_LCDD1,    NULL);
	gpio_request(GPIO_FN_LCDD0,    NULL);
	gpio_request(GPIO_FN_LCDDISP,  NULL);
	gpio_request(GPIO_FN_LCDDCK,   NULL);

	gpio_request(GPIO_PORT31, NULL); /* backlight */
	gpio_direction_output(GPIO_PORT31, 1);

	gpio_request(GPIO_PORT151, NULL); /* LCDDON */
	gpio_direction_output(GPIO_PORT151, 1);

	/* USB enable */
	gpio_request(GPIO_FN_VBUS0_1,    NULL);
	gpio_request(GPIO_FN_IDIN_1_18,  NULL);
	gpio_request(GPIO_FN_PWEN_1_115, NULL);
	gpio_request(GPIO_FN_OVCN_1_114, NULL);
	gpio_request(GPIO_FN_EXTLP_1,    NULL);
	gpio_request(GPIO_FN_OVCN2_1,    NULL);

	/* setup USB phy */
	__raw_writew(0x8a0a, 0xE6058130);	/* USBCR2 */


	sh7372_add_standard_devices();

	platform_add_devices(mackerel_devices, ARRAY_SIZE(mackerel_devices));
}

static void __init mackerel_timer_init(void)
{
	sh7372_clock_init();
	shmobile_timer.init();
}

static struct sys_timer mackerel_timer = {
	.init		= mackerel_timer_init,
};

MACHINE_START(MACKEREL, "mackerel")
	.map_io		= mackerel_map_io,
	.init_irq	= sh7372_init_irq,
	.init_machine	= mackerel_init,
	.timer		= &mackerel_timer,
MACHINE_END