| /* |
| * DRM driver for Sitronix ST7586 panels |
| * |
| * Copyright 2017 David Lechner <david@lechnology.com> |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License as published by |
| * the Free Software Foundation; either version 2 of the License, or |
| * (at your option) any later version. |
| */ |
| |
| #include <linux/delay.h> |
| #include <linux/dma-buf.h> |
| #include <linux/gpio/consumer.h> |
| #include <linux/module.h> |
| #include <linux/property.h> |
| #include <linux/spi/spi.h> |
| #include <video/mipi_display.h> |
| |
| #include <drm/tinydrm/mipi-dbi.h> |
| #include <drm/tinydrm/tinydrm-helpers.h> |
| |
| /* controller-specific commands */ |
| #define ST7586_DISP_MODE_GRAY 0x38 |
| #define ST7586_DISP_MODE_MONO 0x39 |
| #define ST7586_ENABLE_DDRAM 0x3a |
| #define ST7586_SET_DISP_DUTY 0xb0 |
| #define ST7586_SET_PART_DISP 0xb4 |
| #define ST7586_SET_NLINE_INV 0xb5 |
| #define ST7586_SET_VOP 0xc0 |
| #define ST7586_SET_BIAS_SYSTEM 0xc3 |
| #define ST7586_SET_BOOST_LEVEL 0xc4 |
| #define ST7586_SET_VOP_OFFSET 0xc7 |
| #define ST7586_ENABLE_ANALOG 0xd0 |
| #define ST7586_AUTO_READ_CTRL 0xd7 |
| #define ST7586_OTP_RW_CTRL 0xe0 |
| #define ST7586_OTP_CTRL_OUT 0xe1 |
| #define ST7586_OTP_READ 0xe3 |
| |
| #define ST7586_DISP_CTRL_MX BIT(6) |
| #define ST7586_DISP_CTRL_MY BIT(7) |
| |
| /* |
| * The ST7586 controller has an unusual pixel format where 2bpp grayscale is |
| * packed 3 pixels per byte with the first two pixels using 3 bits and the 3rd |
| * pixel using only 2 bits. |
| * |
| * | D7 | D6 | D5 || | || 2bpp | |
| * | (D4) | (D3) | (D2) || D1 | D0 || GRAY | |
| * +------+------+------++------+------++------+ |
| * | 1 | 1 | 1 || 1 | 1 || 0 0 | black |
| * | 1 | 0 | 0 || 1 | 0 || 0 1 | dark gray |
| * | 0 | 1 | 0 || 0 | 1 || 1 0 | light gray |
| * | 0 | 0 | 0 || 0 | 0 || 1 1 | white |
| */ |
| |
| static const u8 st7586_lookup[] = { 0x7, 0x4, 0x2, 0x0 }; |
| |
| static void st7586_xrgb8888_to_gray332(u8 *dst, void *vaddr, |
| struct drm_framebuffer *fb, |
| struct drm_clip_rect *clip) |
| { |
| size_t len = (clip->x2 - clip->x1) * (clip->y2 - clip->y1); |
| unsigned int x, y; |
| u8 *src, *buf, val; |
| |
| buf = kmalloc(len, GFP_KERNEL); |
| if (!buf) |
| return; |
| |
| tinydrm_xrgb8888_to_gray8(buf, vaddr, fb, clip); |
| src = buf; |
| |
| for (y = clip->y1; y < clip->y2; y++) { |
| for (x = clip->x1; x < clip->x2; x += 3) { |
| val = st7586_lookup[*src++ >> 6] << 5; |
| val |= st7586_lookup[*src++ >> 6] << 2; |
| val |= st7586_lookup[*src++ >> 6] >> 1; |
| *dst++ = val; |
| } |
| } |
| |
| kfree(buf); |
| } |
| |
| static int st7586_buf_copy(void *dst, struct drm_framebuffer *fb, |
| struct drm_clip_rect *clip) |
| { |
| struct drm_gem_cma_object *cma_obj = drm_fb_cma_get_gem_obj(fb, 0); |
| struct dma_buf_attachment *import_attach = cma_obj->base.import_attach; |
| void *src = cma_obj->vaddr; |
| int ret = 0; |
| |
| if (import_attach) { |
| ret = dma_buf_begin_cpu_access(import_attach->dmabuf, |
| DMA_FROM_DEVICE); |
| if (ret) |
| return ret; |
| } |
| |
| st7586_xrgb8888_to_gray332(dst, src, fb, clip); |
| |
| if (import_attach) |
| ret = dma_buf_end_cpu_access(import_attach->dmabuf, |
| DMA_FROM_DEVICE); |
| |
| return ret; |
| } |
| |
| static int st7586_fb_dirty(struct drm_framebuffer *fb, |
| struct drm_file *file_priv, unsigned int flags, |
| unsigned int color, struct drm_clip_rect *clips, |
| unsigned int num_clips) |
| { |
| struct tinydrm_device *tdev = fb->dev->dev_private; |
| struct mipi_dbi *mipi = mipi_dbi_from_tinydrm(tdev); |
| struct drm_clip_rect clip; |
| int start, end; |
| int ret = 0; |
| |
| mutex_lock(&tdev->dirty_lock); |
| |
| if (!mipi->enabled) |
| goto out_unlock; |
| |
| /* fbdev can flush even when we're not interested */ |
| if (tdev->pipe.plane.fb != fb) |
| goto out_unlock; |
| |
| tinydrm_merge_clips(&clip, clips, num_clips, flags, fb->width, |
| fb->height); |
| |
| /* 3 pixels per byte, so grow clip to nearest multiple of 3 */ |
| clip.x1 = rounddown(clip.x1, 3); |
| clip.x2 = roundup(clip.x2, 3); |
| |
| DRM_DEBUG("Flushing [FB:%d] x1=%u, x2=%u, y1=%u, y2=%u\n", fb->base.id, |
| clip.x1, clip.x2, clip.y1, clip.y2); |
| |
| ret = st7586_buf_copy(mipi->tx_buf, fb, &clip); |
| if (ret) |
| goto out_unlock; |
| |
| /* Pixels are packed 3 per byte */ |
| start = clip.x1 / 3; |
| end = clip.x2 / 3; |
| |
| mipi_dbi_command(mipi, MIPI_DCS_SET_COLUMN_ADDRESS, |
| (start >> 8) & 0xFF, start & 0xFF, |
| (end >> 8) & 0xFF, (end - 1) & 0xFF); |
| mipi_dbi_command(mipi, MIPI_DCS_SET_PAGE_ADDRESS, |
| (clip.y1 >> 8) & 0xFF, clip.y1 & 0xFF, |
| (clip.y2 >> 8) & 0xFF, (clip.y2 - 1) & 0xFF); |
| |
| ret = mipi_dbi_command_buf(mipi, MIPI_DCS_WRITE_MEMORY_START, |
| (u8 *)mipi->tx_buf, |
| (end - start) * (clip.y2 - clip.y1)); |
| |
| out_unlock: |
| mutex_unlock(&tdev->dirty_lock); |
| |
| if (ret) |
| dev_err_once(fb->dev->dev, "Failed to update display %d\n", |
| ret); |
| |
| return ret; |
| } |
| |
| static const struct drm_framebuffer_funcs st7586_fb_funcs = { |
| .destroy = drm_fb_cma_destroy, |
| .create_handle = drm_fb_cma_create_handle, |
| .dirty = st7586_fb_dirty, |
| }; |
| |
| void st7586_pipe_enable(struct drm_simple_display_pipe *pipe, |
| struct drm_crtc_state *crtc_state) |
| { |
| struct tinydrm_device *tdev = pipe_to_tinydrm(pipe); |
| struct mipi_dbi *mipi = mipi_dbi_from_tinydrm(tdev); |
| struct drm_framebuffer *fb = pipe->plane.fb; |
| struct device *dev = tdev->drm->dev; |
| int ret; |
| u8 addr_mode; |
| |
| DRM_DEBUG_KMS("\n"); |
| |
| mipi_dbi_hw_reset(mipi); |
| ret = mipi_dbi_command(mipi, ST7586_AUTO_READ_CTRL, 0x9f); |
| if (ret) { |
| dev_err(dev, "Error sending command %d\n", ret); |
| return; |
| } |
| |
| mipi_dbi_command(mipi, ST7586_OTP_RW_CTRL, 0x00); |
| |
| msleep(10); |
| |
| mipi_dbi_command(mipi, ST7586_OTP_READ); |
| |
| msleep(20); |
| |
| mipi_dbi_command(mipi, ST7586_OTP_CTRL_OUT); |
| mipi_dbi_command(mipi, MIPI_DCS_EXIT_SLEEP_MODE); |
| mipi_dbi_command(mipi, MIPI_DCS_SET_DISPLAY_OFF); |
| |
| msleep(50); |
| |
| mipi_dbi_command(mipi, ST7586_SET_VOP_OFFSET, 0x00); |
| mipi_dbi_command(mipi, ST7586_SET_VOP, 0xe3, 0x00); |
| mipi_dbi_command(mipi, ST7586_SET_BIAS_SYSTEM, 0x02); |
| mipi_dbi_command(mipi, ST7586_SET_BOOST_LEVEL, 0x04); |
| mipi_dbi_command(mipi, ST7586_ENABLE_ANALOG, 0x1d); |
| mipi_dbi_command(mipi, ST7586_SET_NLINE_INV, 0x00); |
| mipi_dbi_command(mipi, ST7586_DISP_MODE_GRAY); |
| mipi_dbi_command(mipi, ST7586_ENABLE_DDRAM, 0x02); |
| |
| switch (mipi->rotation) { |
| default: |
| addr_mode = 0x00; |
| break; |
| case 90: |
| addr_mode = ST7586_DISP_CTRL_MY; |
| break; |
| case 180: |
| addr_mode = ST7586_DISP_CTRL_MX | ST7586_DISP_CTRL_MY; |
| break; |
| case 270: |
| addr_mode = ST7586_DISP_CTRL_MX; |
| break; |
| } |
| mipi_dbi_command(mipi, MIPI_DCS_SET_ADDRESS_MODE, addr_mode); |
| |
| mipi_dbi_command(mipi, ST7586_SET_DISP_DUTY, 0x7f); |
| mipi_dbi_command(mipi, ST7586_SET_PART_DISP, 0xa0); |
| mipi_dbi_command(mipi, MIPI_DCS_SET_PARTIAL_AREA, 0x00, 0x00, 0x00, 0x77); |
| mipi_dbi_command(mipi, MIPI_DCS_EXIT_INVERT_MODE); |
| |
| msleep(100); |
| |
| mipi_dbi_command(mipi, MIPI_DCS_SET_DISPLAY_ON); |
| |
| mipi->enabled = true; |
| |
| if (fb) |
| fb->funcs->dirty(fb, NULL, 0, 0, NULL, 0); |
| } |
| |
| static void st7586_pipe_disable(struct drm_simple_display_pipe *pipe) |
| { |
| struct tinydrm_device *tdev = pipe_to_tinydrm(pipe); |
| struct mipi_dbi *mipi = mipi_dbi_from_tinydrm(tdev); |
| |
| DRM_DEBUG_KMS("\n"); |
| |
| if (!mipi->enabled) |
| return; |
| |
| mipi_dbi_command(mipi, MIPI_DCS_SET_DISPLAY_OFF); |
| mipi->enabled = false; |
| } |
| |
| static const u32 st7586_formats[] = { |
| DRM_FORMAT_XRGB8888, |
| }; |
| |
| static int st7586_init(struct device *dev, struct mipi_dbi *mipi, |
| const struct drm_simple_display_pipe_funcs *pipe_funcs, |
| struct drm_driver *driver, const struct drm_display_mode *mode, |
| unsigned int rotation) |
| { |
| size_t bufsize = (mode->vdisplay + 2) / 3 * mode->hdisplay; |
| struct tinydrm_device *tdev = &mipi->tinydrm; |
| int ret; |
| |
| mutex_init(&mipi->cmdlock); |
| |
| mipi->tx_buf = devm_kmalloc(dev, bufsize, GFP_KERNEL); |
| if (!mipi->tx_buf) |
| return -ENOMEM; |
| |
| ret = devm_tinydrm_init(dev, tdev, &st7586_fb_funcs, driver); |
| if (ret) |
| return ret; |
| |
| ret = tinydrm_display_pipe_init(tdev, pipe_funcs, |
| DRM_MODE_CONNECTOR_VIRTUAL, |
| st7586_formats, |
| ARRAY_SIZE(st7586_formats), |
| mode, rotation); |
| if (ret) |
| return ret; |
| |
| tdev->drm->mode_config.preferred_depth = 32; |
| mipi->rotation = rotation; |
| |
| drm_mode_config_reset(tdev->drm); |
| |
| DRM_DEBUG_KMS("preferred_depth=%u, rotation = %u\n", |
| tdev->drm->mode_config.preferred_depth, rotation); |
| |
| return 0; |
| } |
| |
| static const struct drm_simple_display_pipe_funcs st7586_pipe_funcs = { |
| .enable = st7586_pipe_enable, |
| .disable = st7586_pipe_disable, |
| .update = tinydrm_display_pipe_update, |
| .prepare_fb = tinydrm_display_pipe_prepare_fb, |
| }; |
| |
| static const struct drm_display_mode st7586_mode = { |
| TINYDRM_MODE(178, 128, 37, 27), |
| }; |
| |
| DEFINE_DRM_GEM_CMA_FOPS(st7586_fops); |
| |
| static struct drm_driver st7586_driver = { |
| .driver_features = DRIVER_GEM | DRIVER_MODESET | DRIVER_PRIME | |
| DRIVER_ATOMIC, |
| .fops = &st7586_fops, |
| TINYDRM_GEM_DRIVER_OPS, |
| .lastclose = tinydrm_lastclose, |
| .debugfs_init = mipi_dbi_debugfs_init, |
| .name = "st7586", |
| .desc = "Sitronix ST7586", |
| .date = "20170801", |
| .major = 1, |
| .minor = 0, |
| }; |
| |
| static const struct of_device_id st7586_of_match[] = { |
| { .compatible = "lego,ev3-lcd" }, |
| {}, |
| }; |
| MODULE_DEVICE_TABLE(of, st7586_of_match); |
| |
| static const struct spi_device_id st7586_id[] = { |
| { "ev3-lcd", 0 }, |
| { }, |
| }; |
| MODULE_DEVICE_TABLE(spi, st7586_id); |
| |
| static int st7586_probe(struct spi_device *spi) |
| { |
| struct device *dev = &spi->dev; |
| struct tinydrm_device *tdev; |
| struct mipi_dbi *mipi; |
| struct gpio_desc *a0; |
| u32 rotation = 0; |
| int ret; |
| |
| mipi = devm_kzalloc(dev, sizeof(*mipi), GFP_KERNEL); |
| if (!mipi) |
| return -ENOMEM; |
| |
| mipi->reset = devm_gpiod_get(dev, "reset", GPIOD_OUT_HIGH); |
| if (IS_ERR(mipi->reset)) { |
| dev_err(dev, "Failed to get gpio 'reset'\n"); |
| return PTR_ERR(mipi->reset); |
| } |
| |
| a0 = devm_gpiod_get(dev, "a0", GPIOD_OUT_LOW); |
| if (IS_ERR(a0)) { |
| dev_err(dev, "Failed to get gpio 'a0'\n"); |
| return PTR_ERR(a0); |
| } |
| |
| device_property_read_u32(dev, "rotation", &rotation); |
| |
| ret = mipi_dbi_spi_init(spi, mipi, a0); |
| if (ret) |
| return ret; |
| |
| /* Cannot read from this controller via SPI */ |
| mipi->read_commands = NULL; |
| |
| /* |
| * we are using 8-bit data, so we are not actually swapping anything, |
| * but setting mipi->swap_bytes makes mipi_dbi_typec3_command() do the |
| * right thing and not use 16-bit transfers (which results in swapped |
| * bytes on little-endian systems and causes out of order data to be |
| * sent to the display). |
| */ |
| mipi->swap_bytes = true; |
| |
| ret = st7586_init(&spi->dev, mipi, &st7586_pipe_funcs, &st7586_driver, |
| &st7586_mode, rotation); |
| if (ret) |
| return ret; |
| |
| tdev = &mipi->tinydrm; |
| |
| ret = devm_tinydrm_register(tdev); |
| if (ret) |
| return ret; |
| |
| spi_set_drvdata(spi, mipi); |
| |
| DRM_DEBUG_DRIVER("Initialized %s:%s @%uMHz on minor %d\n", |
| tdev->drm->driver->name, dev_name(dev), |
| spi->max_speed_hz / 1000000, |
| tdev->drm->primary->index); |
| |
| return 0; |
| } |
| |
| static void st7586_shutdown(struct spi_device *spi) |
| { |
| struct mipi_dbi *mipi = spi_get_drvdata(spi); |
| |
| tinydrm_shutdown(&mipi->tinydrm); |
| } |
| |
| static struct spi_driver st7586_spi_driver = { |
| .driver = { |
| .name = "st7586", |
| .owner = THIS_MODULE, |
| .of_match_table = st7586_of_match, |
| }, |
| .id_table = st7586_id, |
| .probe = st7586_probe, |
| .shutdown = st7586_shutdown, |
| }; |
| module_spi_driver(st7586_spi_driver); |
| |
| MODULE_DESCRIPTION("Sitronix ST7586 DRM driver"); |
| MODULE_AUTHOR("David Lechner <david@lechnology.com>"); |
| MODULE_LICENSE("GPL"); |