Remove multiple KERN_ prefixes from printk formats
Commit 5fd29d6ccbc98884569d6f3105aeca70858b3e0f ("printk: clean up
handling of log-levels and newlines") changed printk semantics. printk
lines with multiple KERN_<level> prefixes are no longer emitted as
before the patch.
<level> is now included in the output on each additional use.
Remove all uses of multiple KERN_<level>s in formats.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
diff --git a/arch/blackfin/kernel/setup.c b/arch/blackfin/kernel/setup.c
index 298f023..6136c33 100644
--- a/arch/blackfin/kernel/setup.c
+++ b/arch/blackfin/kernel/setup.c
@@ -408,13 +408,14 @@
bfin_memmap.map[i].addr + bfin_memmap.map[i].size);
switch (bfin_memmap.map[i].type) {
case BFIN_MEMMAP_RAM:
- printk("(usable)\n");
- break;
+ printk(KERN_CONT "(usable)\n");
+ break;
case BFIN_MEMMAP_RESERVED:
- printk("(reserved)\n");
- break;
- default: printk("type %lu\n", bfin_memmap.map[i].type);
- break;
+ printk(KERN_CONT "(reserved)\n");
+ break;
+ default:
+ printk(KERN_CONT "type %lu\n", bfin_memmap.map[i].type);
+ break;
}
}
}
@@ -614,19 +615,19 @@
printk(KERN_INFO "Kernel Managed Memory: %ldMB\n", _ramend >> 20);
printk(KERN_INFO "Memory map:\n"
- KERN_INFO " fixedcode = 0x%p-0x%p\n"
- KERN_INFO " text = 0x%p-0x%p\n"
- KERN_INFO " rodata = 0x%p-0x%p\n"
- KERN_INFO " bss = 0x%p-0x%p\n"
- KERN_INFO " data = 0x%p-0x%p\n"
- KERN_INFO " stack = 0x%p-0x%p\n"
- KERN_INFO " init = 0x%p-0x%p\n"
- KERN_INFO " available = 0x%p-0x%p\n"
+ " fixedcode = 0x%p-0x%p\n"
+ " text = 0x%p-0x%p\n"
+ " rodata = 0x%p-0x%p\n"
+ " bss = 0x%p-0x%p\n"
+ " data = 0x%p-0x%p\n"
+ " stack = 0x%p-0x%p\n"
+ " init = 0x%p-0x%p\n"
+ " available = 0x%p-0x%p\n"
#ifdef CONFIG_MTD_UCLINUX
- KERN_INFO " rootfs = 0x%p-0x%p\n"
+ " rootfs = 0x%p-0x%p\n"
#endif
#if DMA_UNCACHED_REGION > 0
- KERN_INFO " DMA Zone = 0x%p-0x%p\n"
+ " DMA Zone = 0x%p-0x%p\n"
#endif
, (void *)FIXED_CODE_START, (void *)FIXED_CODE_END,
_stext, _etext,
@@ -859,13 +860,13 @@
#endif
printk(KERN_INFO "Hardware Trace ");
if (bfin_read_TBUFCTL() & 0x1)
- printk("Active ");
+ printk(KERN_CONT "Active ");
else
- printk("Off ");
+ printk(KERN_CONT "Off ");
if (bfin_read_TBUFCTL() & 0x2)
- printk("and Enabled\n");
+ printk(KERN_CONT "and Enabled\n");
else
- printk("and Disabled\n");
+ printk(KERN_CONT "and Disabled\n");
#if defined(CONFIG_CHR_DEV_FLASH) || defined(CONFIG_BLK_DEV_FLASH)
/* we need to initialize the Flashrom device here since we might