Remove multiple KERN_ prefixes from printk formats
Commit 5fd29d6ccbc98884569d6f3105aeca70858b3e0f ("printk: clean up
handling of log-levels and newlines") changed printk semantics. printk
lines with multiple KERN_<level> prefixes are no longer emitted as
before the patch.
<level> is now included in the output on each additional use.
Remove all uses of multiple KERN_<level>s in formats.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
diff --git a/arch/blackfin/kernel/setup.c b/arch/blackfin/kernel/setup.c
index 298f023..6136c33 100644
--- a/arch/blackfin/kernel/setup.c
+++ b/arch/blackfin/kernel/setup.c
@@ -408,13 +408,14 @@
bfin_memmap.map[i].addr + bfin_memmap.map[i].size);
switch (bfin_memmap.map[i].type) {
case BFIN_MEMMAP_RAM:
- printk("(usable)\n");
- break;
+ printk(KERN_CONT "(usable)\n");
+ break;
case BFIN_MEMMAP_RESERVED:
- printk("(reserved)\n");
- break;
- default: printk("type %lu\n", bfin_memmap.map[i].type);
- break;
+ printk(KERN_CONT "(reserved)\n");
+ break;
+ default:
+ printk(KERN_CONT "type %lu\n", bfin_memmap.map[i].type);
+ break;
}
}
}
@@ -614,19 +615,19 @@
printk(KERN_INFO "Kernel Managed Memory: %ldMB\n", _ramend >> 20);
printk(KERN_INFO "Memory map:\n"
- KERN_INFO " fixedcode = 0x%p-0x%p\n"
- KERN_INFO " text = 0x%p-0x%p\n"
- KERN_INFO " rodata = 0x%p-0x%p\n"
- KERN_INFO " bss = 0x%p-0x%p\n"
- KERN_INFO " data = 0x%p-0x%p\n"
- KERN_INFO " stack = 0x%p-0x%p\n"
- KERN_INFO " init = 0x%p-0x%p\n"
- KERN_INFO " available = 0x%p-0x%p\n"
+ " fixedcode = 0x%p-0x%p\n"
+ " text = 0x%p-0x%p\n"
+ " rodata = 0x%p-0x%p\n"
+ " bss = 0x%p-0x%p\n"
+ " data = 0x%p-0x%p\n"
+ " stack = 0x%p-0x%p\n"
+ " init = 0x%p-0x%p\n"
+ " available = 0x%p-0x%p\n"
#ifdef CONFIG_MTD_UCLINUX
- KERN_INFO " rootfs = 0x%p-0x%p\n"
+ " rootfs = 0x%p-0x%p\n"
#endif
#if DMA_UNCACHED_REGION > 0
- KERN_INFO " DMA Zone = 0x%p-0x%p\n"
+ " DMA Zone = 0x%p-0x%p\n"
#endif
, (void *)FIXED_CODE_START, (void *)FIXED_CODE_END,
_stext, _etext,
@@ -859,13 +860,13 @@
#endif
printk(KERN_INFO "Hardware Trace ");
if (bfin_read_TBUFCTL() & 0x1)
- printk("Active ");
+ printk(KERN_CONT "Active ");
else
- printk("Off ");
+ printk(KERN_CONT "Off ");
if (bfin_read_TBUFCTL() & 0x2)
- printk("and Enabled\n");
+ printk(KERN_CONT "and Enabled\n");
else
- printk("and Disabled\n");
+ printk(KERN_CONT "and Disabled\n");
#if defined(CONFIG_CHR_DEV_FLASH) || defined(CONFIG_BLK_DEV_FLASH)
/* we need to initialize the Flashrom device here since we might
diff --git a/arch/blackfin/kernel/traps.c b/arch/blackfin/kernel/traps.c
index 8eeb457..8a1caf2 100644
--- a/arch/blackfin/kernel/traps.c
+++ b/arch/blackfin/kernel/traps.c
@@ -212,7 +212,7 @@
console_verbose();
oops_in_progress = 1;
#ifdef CONFIG_DEBUG_VERBOSE
- printk(KERN_EMERG "\n" KERN_EMERG "Double Fault\n");
+ printk(KERN_EMERG "Double Fault\n");
#ifdef CONFIG_DEBUG_DOUBLEFAULT_PRINT
if (((long)fp->seqstat & SEQSTAT_EXCAUSE) == VEC_UNCOV) {
unsigned int cpu = smp_processor_id();
@@ -583,15 +583,14 @@
#ifndef CONFIG_DEBUG_BFIN_NO_KERN_HWTRACE
if (trapnr == VEC_CPLB_I_M || trapnr == VEC_CPLB_M)
verbose_printk(KERN_NOTICE "No trace since you do not have "
- "CONFIG_DEBUG_BFIN_NO_KERN_HWTRACE enabled\n"
- KERN_NOTICE "\n");
+ "CONFIG_DEBUG_BFIN_NO_KERN_HWTRACE enabled\n\n");
else
#endif
dump_bfin_trace_buffer();
if (oops_in_progress) {
/* Dump the current kernel stack */
- verbose_printk(KERN_NOTICE "\n" KERN_NOTICE "Kernel Stack\n");
+ verbose_printk(KERN_NOTICE "Kernel Stack\n");
show_stack(current, NULL);
print_modules();
#ifndef CONFIG_ACCESS_CHECK
@@ -906,7 +905,7 @@
ret_addr = 0;
if (!j && i % 8 == 0)
- printk("\n" KERN_NOTICE "%p:",addr);
+ printk(KERN_NOTICE "%p:",addr);
/* if it is an odd address, or zero, just skip it */
if (*addr & 0x1 || !*addr)
@@ -996,9 +995,9 @@
printk(KERN_NOTICE "CPU = %d\n", current_thread_info()->cpu);
if (!((unsigned long)current->mm & 0x3) && (unsigned long)current->mm >= FIXED_CODE_START)
- verbose_printk(KERN_NOTICE "TEXT = 0x%p-0x%p DATA = 0x%p-0x%p\n"
- KERN_NOTICE " BSS = 0x%p-0x%p USER-STACK = 0x%p\n"
- KERN_NOTICE "\n",
+ verbose_printk(KERN_NOTICE
+ "TEXT = 0x%p-0x%p DATA = 0x%p-0x%p\n"
+ " BSS = 0x%p-0x%p USER-STACK = 0x%p\n\n",
(void *)current->mm->start_code,
(void *)current->mm->end_code,
(void *)current->mm->start_data,
@@ -1009,8 +1008,8 @@
else
verbose_printk(KERN_NOTICE "invalid mm\n");
} else
- verbose_printk(KERN_NOTICE "\n" KERN_NOTICE
- "No Valid process in current context\n");
+ verbose_printk(KERN_NOTICE
+ "No Valid process in current context\n");
#endif
}
@@ -1028,7 +1027,7 @@
addr < (unsigned short *)((unsigned long)erraddr & ~0xF) + 0x10;
addr++) {
if (!((unsigned long)addr & 0xF))
- verbose_printk("\n" KERN_NOTICE "0x%p: ", addr);
+ verbose_printk(KERN_NOTICE "0x%p: ", addr);
if (!get_instruction(&val, addr)) {
val = 0;
@@ -1056,9 +1055,9 @@
oops_in_progress)){
verbose_printk(KERN_NOTICE "Looks like this was a deferred error - sorry\n");
#ifndef CONFIG_DEBUG_HWERR
- verbose_printk(KERN_NOTICE "The remaining message may be meaningless\n"
- KERN_NOTICE "You should enable CONFIG_DEBUG_HWERR to get a"
- " better idea where it came from\n");
+ verbose_printk(KERN_NOTICE
+"The remaining message may be meaningless\n"
+"You should enable CONFIG_DEBUG_HWERR to get a better idea where it came from\n");
#else
/* If we are handling only one peripheral interrupt
* and current mm and pid are valid, and the last error
@@ -1114,9 +1113,10 @@
verbose_printk(KERN_NOTICE "%s", linux_banner);
- verbose_printk(KERN_NOTICE "\n" KERN_NOTICE "SEQUENCER STATUS:\t\t%s\n", print_tainted());
+ verbose_printk(KERN_NOTICE "\nSEQUENCER STATUS:\t\t%s\n",
+ print_tainted());
verbose_printk(KERN_NOTICE " SEQSTAT: %08lx IPEND: %04lx SYSCFG: %04lx\n",
- (long)fp->seqstat, fp->ipend, fp->syscfg);
+ (long)fp->seqstat, fp->ipend, fp->syscfg);
if ((fp->seqstat & SEQSTAT_EXCAUSE) == VEC_HWERR) {
verbose_printk(KERN_NOTICE " HWERRCAUSE: 0x%lx\n",
(fp->seqstat & SEQSTAT_HWERRCAUSE) >> 14);
@@ -1184,7 +1184,7 @@
verbose_printk(KERN_NOTICE "ICPLB_FAULT_ADDR: %s\n", buf);
}
- verbose_printk(KERN_NOTICE "\n" KERN_NOTICE "PROCESSOR STATE:\n");
+ verbose_printk(KERN_NOTICE "PROCESSOR STATE:\n");
verbose_printk(KERN_NOTICE " R0 : %08lx R1 : %08lx R2 : %08lx R3 : %08lx\n",
fp->r0, fp->r1, fp->r2, fp->r3);
verbose_printk(KERN_NOTICE " R4 : %08lx R5 : %08lx R6 : %08lx R7 : %08lx\n",