drivers/net/hamradio/Kconfig - SHIFTPHONES/mainline/linux - Gitiles

 # SPDX-License-Identifier: GPL-2.0-only
 config MKISS
 	tristate "Serial port KISS driver"
 	depends on AX25 && TTY
 	select CRC16
 	help
 	  KISS is a protocol used for the exchange of data between a computer
 	  and a Terminal Node Controller (a small embedded system commonly
 	  used for networking over AX.25 amateur radio connections; it
 	  connects the computer's serial port with the radio's microphone
 	  input and speaker output).

 	  Although KISS is less advanced than the 6pack protocol, it has
 	  the advantage that it is already supported by most modern TNCs
 	  without the need for a firmware upgrade.

 	  To compile this driver as a module, choose M here: the module
 	  will be called mkiss.

 config 6PACK
 	tristate "Serial port 6PACK driver"
 	depends on AX25 && TTY
 	help
 	  6pack is a transmission protocol for the data exchange between your
 	  PC and your TNC (the Terminal Node Controller acts as a kind of
 	  modem connecting your computer's serial port to your radio's
 	  microphone input and speaker output). This protocol can be used as
 	  an alternative to KISS for networking over AX.25 amateur radio
 	  connections, but it has some extended functionality.

 	  Note that this driver is still experimental and might cause
 	  problems. For details about the features and the usage of the
 	  driver, read <file:Documentation/networking/6pack.rst>.

 	  To compile this driver as a module, choose M here: the module
 	  will be called 6pack.

 config BPQETHER
 	tristate "BPQ Ethernet driver"
 	depends on AX25
 	help
 	  AX.25 is the protocol used for computer communication over amateur
 	  radio. If you say Y here, you will be able to send and receive AX.25
 	  traffic over Ethernet (also called "BPQ AX.25"), which could be
 	  useful if some other computer on your local network has a direct
 	  amateur radio connection.

 config DMASCC
 	tristate "High-speed (DMA) SCC driver for AX.25"
 	depends on ISA && AX25 && BROKEN_ON_SMP && ISA_DMA_API
 	help
 	  This is a driver for high-speed SCC boards, i.e. those supporting
 	  DMA on one port. You usually use those boards to connect your
 	  computer to an amateur radio modem (such as the WA4DSY 56kbps
 	  modem), in order to send and receive AX.25 packet radio network
 	  traffic.

 	  Currently, this driver supports Ottawa PI/PI2, Paccomm/Gracilis
 	  PackeTwin, and S5SCC/DMA boards. They are detected automatically.
 	  If you have one of these cards, say Y here and read the AX25-HOWTO,
 	  available from <http://www.tldp.org/docs.html#howto>.

 	  This driver can operate multiple boards simultaneously. If you
 	  compile it as a module (by saying M instead of Y), it will be called
 	  dmascc. If you don't pass any parameter to the driver, all
 	  possible I/O addresses are probed. This could irritate other devices
 	  that are currently not in use. You may specify the list of addresses
 	  to be probed by "dmascc.io=addr1,addr2,..." (when compiled into the
 	  kernel image) or "io=addr1,addr2,..." (when loaded as a module). The
 	  network interfaces will be called dmascc0 and dmascc1 for the board
 	  detected first, dmascc2 and dmascc3 for the second one, and so on.

 	  Before you configure each interface with ifconfig, you MUST set
 	  certain parameters, such as channel access timing, clock mode, and
 	  DMA channel. This is accomplished with a small utility program,
 	  dmascc_cfg, available at
 	  <http://www.linux-ax25.org/wiki/Ax25-tools>. Please be sure to
 	  get at least version 1.27 of dmascc_cfg, as older versions will not
 	  work with the current driver.

 config SCC
 	tristate "Z8530 SCC driver"
 	depends on ISA && AX25 && ISA_DMA_API
 	help
 	  These cards are used to connect your Linux box to an amateur radio
 	  in order to communicate with other computers. If you want to use
 	  this, read <file:Documentation/networking/z8530drv.rst> and the
 	  AX25-HOWTO, available from
 	  <http://www.tldp.org/docs.html#howto>. Also make sure to say Y
 	  to "Amateur Radio AX.25 Level 2" support.

 	  To compile this driver as a module, choose M here: the module
 	  will be called scc.

 config SCC_DELAY
 	bool "additional delay for PA0HZP OptoSCC compatible boards"
 	depends on SCC
 	help
 	  Say Y here if you experience problems with the SCC driver not
 	  working properly; please read
 	  <file:Documentation/networking/z8530drv.rst> for details.

 	  If unsure, say N.

 config SCC_TRXECHO
 	bool "support for TRX that feedback the tx signal to rx"
 	depends on SCC
 	help
 	  Some transmitters feed the transmitted signal back to the receive
 	  line.  Say Y here to foil this by explicitly disabling the receiver
 	  during data transmission.

 	  If in doubt, say Y.

 config BAYCOM_SER_FDX
 	tristate "BAYCOM ser12 fullduplex driver for AX.25"
 	depends on AX25 && !S390
 	select CRC_CCITT
 	help
 	  This is one of two drivers for Baycom style simple amateur radio
 	  modems that connect to a serial interface. The driver supports the
 	  ser12 design in full-duplex mode. In addition, it allows the
 	  baudrate to be set between 300 and 4800 baud (however not all modems
 	  support all baudrates). This is the preferred driver. The next
 	  driver, "BAYCOM ser12 half-duplex driver for AX.25" is the old
 	  driver and still provided in case this driver does not work with
 	  your serial interface chip. To configure the driver, use the sethdlc
 	  utility available in the standard ax25 utilities package. For
 	  information on the modems, see <http://www.baycom.de/> and
 	  <file:Documentation/networking/baycom.rst>.

 	  To compile this driver as a module, choose M here: the module
 	  will be called baycom_ser_fdx.  This is recommended.

 config BAYCOM_SER_HDX
 	tristate "BAYCOM ser12 halfduplex driver for AX.25"
 	depends on AX25 && !S390
 	select CRC_CCITT
 	help
 	  This is one of two drivers for Baycom style simple amateur radio
 	  modems that connect to a serial interface. The driver supports the
 	  ser12 design in half-duplex mode. This is the old driver.  It is
 	  still provided in case your serial interface chip does not work with
 	  the full-duplex driver. This driver is deprecated.  To configure
 	  the driver, use the sethdlc utility available in the standard ax25
 	  utilities package. For information on the modems, see
 	  <http://www.baycom.de/> and
 	  <file:Documentation/networking/baycom.rst>.

 	  To compile this driver as a module, choose M here: the module
 	  will be called baycom_ser_hdx.  This is recommended.

 config BAYCOM_PAR
 	tristate "BAYCOM picpar and par96 driver for AX.25"
 	depends on PARPORT && AX25
 	select CRC_CCITT
 	help
 	  This is a driver for Baycom style simple amateur radio modems that
 	  connect to a parallel interface. The driver supports the picpar and
 	  par96 designs. To configure the driver, use the sethdlc utility
 	  available in the standard ax25 utilities package. For information on
 	  the modems, see <http://www.baycom.de/> and the file
 	  <file:Documentation/networking/baycom.rst>.

 	  To compile this driver as a module, choose M here: the module
 	  will be called baycom_par.  This is recommended.

 config BAYCOM_EPP
 	tristate "BAYCOM epp driver for AX.25"
 	depends on PARPORT && AX25 && !64BIT
 	select CRC_CCITT
 	help
 	  This is a driver for Baycom style simple amateur radio modems that
 	  connect to a parallel interface. The driver supports the EPP
 	  designs. To configure the driver, use the sethdlc utility available
 	  in the standard ax25 utilities package. For information on the
 	  modems, see <http://www.baycom.de/> and the file
 	  <file:Documentation/networking/baycom.rst>.

 	  To compile this driver as a module, choose M here: the module
 	  will be called baycom_epp.  This is recommended.

 config YAM
 	tristate "YAM driver for AX.25"
 	depends on AX25 && !S390
 	help
 	  The YAM is a modem for packet radio which connects to the serial
 	  port and includes some of the functions of a Terminal Node
 	  Controller. If you have one of those, say Y here.

 	  To compile this driver as a module, choose M here: the module
 	  will be called yam.
	# SPDX-License-Identifier: GPL-2.0-only
	config MKISS
	tristate "Serial port KISS driver"
	depends on AX25 && TTY
	select CRC16
	help
	KISS is a protocol used for the exchange of data between a computer
	and a Terminal Node Controller (a small embedded system commonly
	used for networking over AX.25 amateur radio connections; it
	connects the computer's serial port with the radio's microphone
	input and speaker output).

	Although KISS is less advanced than the 6pack protocol, it has
	the advantage that it is already supported by most modern TNCs
	without the need for a firmware upgrade.

	To compile this driver as a module, choose M here: the module
	will be called mkiss.

	config 6PACK
	tristate "Serial port 6PACK driver"
	depends on AX25 && TTY
	help
	6pack is a transmission protocol for the data exchange between your
	PC and your TNC (the Terminal Node Controller acts as a kind of
	modem connecting your computer's serial port to your radio's
	microphone input and speaker output). This protocol can be used as
	an alternative to KISS for networking over AX.25 amateur radio
	connections, but it has some extended functionality.

	Note that this driver is still experimental and might cause
	problems. For details about the features and the usage of the
	driver, read <file:Documentation/networking/6pack.rst>.

	To compile this driver as a module, choose M here: the module
	will be called 6pack.

	config BPQETHER
	tristate "BPQ Ethernet driver"
	depends on AX25
	help
	AX.25 is the protocol used for computer communication over amateur
	radio. If you say Y here, you will be able to send and receive AX.25
	traffic over Ethernet (also called "BPQ AX.25"), which could be
	useful if some other computer on your local network has a direct
	amateur radio connection.

	config DMASCC
	tristate "High-speed (DMA) SCC driver for AX.25"
	depends on ISA && AX25 && BROKEN_ON_SMP && ISA_DMA_API
	help
	This is a driver for high-speed SCC boards, i.e. those supporting
	DMA on one port. You usually use those boards to connect your
	computer to an amateur radio modem (such as the WA4DSY 56kbps
	modem), in order to send and receive AX.25 packet radio network
	traffic.

	Currently, this driver supports Ottawa PI/PI2, Paccomm/Gracilis
	PackeTwin, and S5SCC/DMA boards. They are detected automatically.
	If you have one of these cards, say Y here and read the AX25-HOWTO,
	available from <http://www.tldp.org/docs.html#howto>.

	This driver can operate multiple boards simultaneously. If you
	compile it as a module (by saying M instead of Y), it will be called
	dmascc. If you don't pass any parameter to the driver, all
	possible I/O addresses are probed. This could irritate other devices
	that are currently not in use. You may specify the list of addresses
	to be probed by "dmascc.io=addr1,addr2,..." (when compiled into the
	kernel image) or "io=addr1,addr2,..." (when loaded as a module). The
	network interfaces will be called dmascc0 and dmascc1 for the board
	detected first, dmascc2 and dmascc3 for the second one, and so on.

	Before you configure each interface with ifconfig, you MUST set
	certain parameters, such as channel access timing, clock mode, and
	DMA channel. This is accomplished with a small utility program,
	dmascc_cfg, available at
	<http://www.linux-ax25.org/wiki/Ax25-tools>. Please be sure to
	get at least version 1.27 of dmascc_cfg, as older versions will not
	work with the current driver.

	config SCC
	tristate "Z8530 SCC driver"
	depends on ISA && AX25 && ISA_DMA_API
	help
	These cards are used to connect your Linux box to an amateur radio
	in order to communicate with other computers. If you want to use
	this, read <file:Documentation/networking/z8530drv.rst> and the
	AX25-HOWTO, available from
	<http://www.tldp.org/docs.html#howto>. Also make sure to say Y
	to "Amateur Radio AX.25 Level 2" support.

	To compile this driver as a module, choose M here: the module
	will be called scc.

	config SCC_DELAY
	bool "additional delay for PA0HZP OptoSCC compatible boards"
	depends on SCC
	help
	Say Y here if you experience problems with the SCC driver not
	working properly; please read
	<file:Documentation/networking/z8530drv.rst> for details.

	If unsure, say N.

	config SCC_TRXECHO
	bool "support for TRX that feedback the tx signal to rx"
	depends on SCC
	help
	Some transmitters feed the transmitted signal back to the receive
	line. Say Y here to foil this by explicitly disabling the receiver
	during data transmission.

	If in doubt, say Y.

	config BAYCOM_SER_FDX
	tristate "BAYCOM ser12 fullduplex driver for AX.25"
	depends on AX25 && !S390
	select CRC_CCITT
	help
	This is one of two drivers for Baycom style simple amateur radio
	modems that connect to a serial interface. The driver supports the
	ser12 design in full-duplex mode. In addition, it allows the
	baudrate to be set between 300 and 4800 baud (however not all modems
	support all baudrates). This is the preferred driver. The next
	driver, "BAYCOM ser12 half-duplex driver for AX.25" is the old
	driver and still provided in case this driver does not work with
	your serial interface chip. To configure the driver, use the sethdlc
	utility available in the standard ax25 utilities package. For
	information on the modems, see <http://www.baycom.de/> and
	<file:Documentation/networking/baycom.rst>.

	To compile this driver as a module, choose M here: the module
	will be called baycom_ser_fdx. This is recommended.

	config BAYCOM_SER_HDX
	tristate "BAYCOM ser12 halfduplex driver for AX.25"
	depends on AX25 && !S390
	select CRC_CCITT
	help
	This is one of two drivers for Baycom style simple amateur radio
	modems that connect to a serial interface. The driver supports the
	ser12 design in half-duplex mode. This is the old driver. It is
	still provided in case your serial interface chip does not work with
	the full-duplex driver. This driver is deprecated. To configure
	the driver, use the sethdlc utility available in the standard ax25
	utilities package. For information on the modems, see
	<http://www.baycom.de/> and
	<file:Documentation/networking/baycom.rst>.

	To compile this driver as a module, choose M here: the module
	will be called baycom_ser_hdx. This is recommended.

	config BAYCOM_PAR
	tristate "BAYCOM picpar and par96 driver for AX.25"
	depends on PARPORT && AX25
	select CRC_CCITT
	help
	This is a driver for Baycom style simple amateur radio modems that
	connect to a parallel interface. The driver supports the picpar and
	par96 designs. To configure the driver, use the sethdlc utility
	available in the standard ax25 utilities package. For information on
	the modems, see <http://www.baycom.de/> and the file
	<file:Documentation/networking/baycom.rst>.

	To compile this driver as a module, choose M here: the module
	will be called baycom_par. This is recommended.

	config BAYCOM_EPP
	tristate "BAYCOM epp driver for AX.25"
	depends on PARPORT && AX25 && !64BIT
	select CRC_CCITT
	help
	This is a driver for Baycom style simple amateur radio modems that
	connect to a parallel interface. The driver supports the EPP
	designs. To configure the driver, use the sethdlc utility available
	in the standard ax25 utilities package. For information on the
	modems, see <http://www.baycom.de/> and the file
	<file:Documentation/networking/baycom.rst>.

	To compile this driver as a module, choose M here: the module
	will be called baycom_epp. This is recommended.

	config YAM
	tristate "YAM driver for AX.25"
	depends on AX25 && !S390
	help
	The YAM is a modem for packet radio which connects to the serial
	port and includes some of the functions of a Terminal Node
	Controller. If you have one of those, say Y here.

	To compile this driver as a module, choose M here: the module
	will be called yam.