drivers/serial/sunsu.c

/* $Id: su.c,v 1.55 2002/01/08 16:00:16 davem Exp $
 * su.c: Small serial driver for keyboard/mouse interface on sparc32/PCI
 *
 * Copyright (C) 1997  Eddie C. Dost  (ecd@skynet.be)
 * Copyright (C) 1998-1999  Pete Zaitcev   (zaitcev@yahoo.com)
 *
 * This is mainly a variation of 8250.c, credits go to authors mentioned
 * therein.  In fact this driver should be merged into the generic 8250.c
 * infrastructure perhaps using a 8250_sparc.c module.
 *
 * Fixed to use tty_get_baud_rate().
 *   Theodore Ts'o <tytso@mit.edu>, 2001-Oct-12
 *
 * Converted to new 2.5.x UART layer.
 *   David S. Miller (davem@redhat.com), 2002-Jul-29
 */

#include <linux/config.h>
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/sched.h>
#include <linux/spinlock.h>
#include <linux/errno.h>
#include <linux/tty.h>
#include <linux/tty_flip.h>
#include <linux/major.h>
#include <linux/string.h>
#include <linux/ptrace.h>
#include <linux/ioport.h>
#include <linux/circ_buf.h>
#include <linux/serial.h>
#include <linux/sysrq.h>
#include <linux/console.h>
#ifdef CONFIG_SERIO
#include <linux/serio.h>
#endif
#include <linux/serial_reg.h>
#include <linux/init.h>
#include <linux/delay.h>

#include <asm/io.h>
#include <asm/irq.h>
#include <asm/oplib.h>
#include <asm/ebus.h>
#ifdef CONFIG_SPARC64
#include <asm/isa.h>
#endif

#if defined(CONFIG_SERIAL_SUNSU_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
#define SUPPORT_SYSRQ
#endif

#include <linux/serial_core.h>

#include "suncore.h"

/* We are on a NS PC87303 clocked with 24.0 MHz, which results
 * in a UART clock of 1.8462 MHz.
 */
#define SU_BASE_BAUD	(1846200 / 16)

enum su_type { SU_PORT_NONE, SU_PORT_MS, SU_PORT_KBD, SU_PORT_PORT };
static char *su_typev[] = { "su(???)", "su(mouse)", "su(kbd)", "su(serial)" };

/*
 * Here we define the default xmit fifo size used for each type of UART.
 */
static const struct serial_uart_config uart_config[PORT_MAX_8250+1] = {
	{ "unknown",	1,	0 },
	{ "8250",	1,	0 },
	{ "16450",	1,	0 },
	{ "16550",	1,	0 },
	{ "16550A",	16,	UART_CLEAR_FIFO | UART_USE_FIFO },
	{ "Cirrus",	1, 	0 },
	{ "ST16650",	1,	UART_CLEAR_FIFO | UART_STARTECH },
	{ "ST16650V2",	32,	UART_CLEAR_FIFO | UART_USE_FIFO | UART_STARTECH },
	{ "TI16750",	64,	UART_CLEAR_FIFO | UART_USE_FIFO },
	{ "Startech",	1,	0 },
	{ "16C950/954",	128,	UART_CLEAR_FIFO | UART_USE_FIFO },
	{ "ST16654",	64,	UART_CLEAR_FIFO | UART_USE_FIFO | UART_STARTECH },
	{ "XR16850",	128,	UART_CLEAR_FIFO | UART_USE_FIFO | UART_STARTECH },
	{ "RSA",	2048,	UART_CLEAR_FIFO | UART_USE_FIFO }
};

struct uart_sunsu_port {
	struct uart_port	port;
	unsigned char		acr;
	unsigned char		ier;
	unsigned short		rev;
	unsigned char		lcr;
	unsigned int		lsr_break_flag;
	unsigned int		cflag;

	/* Probing information.  */
	enum su_type		su_type;
	unsigned int		type_probed;	/* XXX Stupid */
	int			port_node;

#ifdef CONFIG_SERIO
	struct serio		*serio;
	int			serio_open;
#endif
};

static unsigned int serial_in(struct uart_sunsu_port *up, int offset)
{
	offset <<= up->port.regshift;

	switch (up->port.iotype) {
	case UPIO_HUB6:
		outb(up->port.hub6 - 1 + offset, up->port.iobase);
		return inb(up->port.iobase + 1);

	case UPIO_MEM:
		return readb(up->port.membase + offset);

	default:
		return inb(up->port.iobase + offset);
	}
}

static void serial_out(struct uart_sunsu_port *up, int offset, int value)
{
#ifndef CONFIG_SPARC64
	/*
	 * MrCoffee has weird schematics: IRQ4 & P10(?) pins of SuperIO are
	 * connected with a gate then go to SlavIO. When IRQ4 goes tristated
	 * gate outputs a logical one. Since we use level triggered interrupts
	 * we have lockup and watchdog reset. We cannot mask IRQ because
	 * keyboard shares IRQ with us (Word has it as Bob Smelik's design).
	 * This problem is similar to what Alpha people suffer, see serial.c.
	 */
	if (offset == UART_MCR)
		value |= UART_MCR_OUT2;
#endif
	offset <<= up->port.regshift;

	switch (up->port.iotype) {
	case UPIO_HUB6:
		outb(up->port.hub6 - 1 + offset, up->port.iobase);
		outb(value, up->port.iobase + 1);
		break;

	case UPIO_MEM:
		writeb(value, up->port.membase + offset);
		break;

	default:
		outb(value, up->port.iobase + offset);
	}
}

/*
 * We used to support using pause I/O for certain machines.  We
 * haven't supported this for a while, but just in case it's badly
 * needed for certain old 386 machines, I've left these #define's
 * in....
 */
#define serial_inp(up, offset)		serial_in(up, offset)
#define serial_outp(up, offset, value)	serial_out(up, offset, value)


/*
 * For the 16C950
 */
static void serial_icr_write(struct uart_sunsu_port *up, int offset, int value)
{
	serial_out(up, UART_SCR, offset);
	serial_out(up, UART_ICR, value);
}

#if 0 /* Unused currently */
static unsigned int serial_icr_read(struct uart_sunsu_port *up, int offset)
{
	unsigned int value;

	serial_icr_write(up, UART_ACR, up->acr | UART_ACR_ICRRD);
	serial_out(up, UART_SCR, offset);
	value = serial_in(up, UART_ICR);
	serial_icr_write(up, UART_ACR, up->acr);

	return value;
}
#endif

#ifdef CONFIG_SERIAL_8250_RSA
/*
 * Attempts to turn on the RSA FIFO.  Returns zero on failure.
 * We set the port uart clock rate if we succeed.
 */
static int __enable_rsa(struct uart_sunsu_port *up)
{
	unsigned char mode;
	int result;

	mode = serial_inp(up, UART_RSA_MSR);
	result = mode & UART_RSA_MSR_FIFO;

	if (!result) {
		serial_outp(up, UART_RSA_MSR, mode | UART_RSA_MSR_FIFO);
		mode = serial_inp(up, UART_RSA_MSR);
		result = mode & UART_RSA_MSR_FIFO;
	}

	if (result)
		up->port.uartclk = SERIAL_RSA_BAUD_BASE * 16;

	return result;
}

static void enable_rsa(struct uart_sunsu_port *up)
{
	if (up->port.type == PORT_RSA) {
		if (up->port.uartclk != SERIAL_RSA_BAUD_BASE * 16) {
			spin_lock_irq(&up->port.lock);
			__enable_rsa(up);
			spin_unlock_irq(&up->port.lock);
		}
		if (up->port.uartclk == SERIAL_RSA_BAUD_BASE * 16)
			serial_outp(up, UART_RSA_FRR, 0);
	}
}

/*
 * Attempts to turn off the RSA FIFO.  Returns zero on failure.
 * It is unknown why interrupts were disabled in here.  However,
 * the caller is expected to preserve this behaviour by grabbing
 * the spinlock before calling this function.
 */
static void disable_rsa(struct uart_sunsu_port *up)
{
	unsigned char mode;
	int result;

	if (up->port.type == PORT_RSA &&
	    up->port.uartclk == SERIAL_RSA_BAUD_BASE * 16) {
		spin_lock_irq(&up->port.lock);

		mode = serial_inp(up, UART_RSA_MSR);
		result = !(mode & UART_RSA_MSR_FIFO);

		if (!result) {
			serial_outp(up, UART_RSA_MSR, mode & ~UART_RSA_MSR_FIFO);
			mode = serial_inp(up, UART_RSA_MSR);
			result = !(mode & UART_RSA_MSR_FIFO);
		}

		if (result)
			up->port.uartclk = SERIAL_RSA_BAUD_BASE_LO * 16;
		spin_unlock_irq(&up->port.lock);
	}
}
#endif /* CONFIG_SERIAL_8250_RSA */

static inline void __stop_tx(struct uart_sunsu_port *p)
{
	if (p->ier & UART_IER_THRI) {
		p->ier &= ~UART_IER_THRI;
		serial_out(p, UART_IER, p->ier);
	}
}

static void sunsu_stop_tx(struct uart_port *port)
{
	struct uart_sunsu_port *up = (struct uart_sunsu_port *) port;

	__stop_tx(up);

	/*
	 * We really want to stop the transmitter from sending.
	 */
	if (up->port.type == PORT_16C950) {
		up->acr |= UART_ACR_TXDIS;
		serial_icr_write(up, UART_ACR, up->acr);
	}
}

static void sunsu_start_tx(struct uart_port *port)
{
	struct uart_sunsu_port *up = (struct uart_sunsu_port *) port;

	if (!(up->ier & UART_IER_THRI)) {
		up->ier |= UART_IER_THRI;
		serial_out(up, UART_IER, up->ier);
	}

	/*
	 * Re-enable the transmitter if we disabled it.
	 */
	if (up->port.type == PORT_16C950 && up->acr & UART_ACR_TXDIS) {
		up->acr &= ~UART_ACR_TXDIS;
		serial_icr_write(up, UART_ACR, up->acr);
	}
}

static void sunsu_stop_rx(struct uart_port *port)
{
	struct uart_sunsu_port *up = (struct uart_sunsu_port *) port;

	up->ier &= ~UART_IER_RLSI;
	up->port.read_status_mask &= ~UART_LSR_DR;
	serial_out(up, UART_IER, up->ier);
}

static void sunsu_enable_ms(struct uart_port *port)
{
	struct uart_sunsu_port *up = (struct uart_sunsu_port *) port;
	unsigned long flags;

	spin_lock_irqsave(&up->port.lock, flags);
	up->ier |= UART_IER_MSI;
	serial_out(up, UART_IER, up->ier);
	spin_unlock_irqrestore(&up->port.lock, flags);
}

static struct tty_struct *
receive_chars(struct uart_sunsu_port *up, unsigned char *status, struct pt_regs *regs)
{
	struct tty_struct *tty = up->port.info->tty;
	unsigned char ch, flag;
	int max_count = 256;
	int saw_console_brk = 0;

	do {
		ch = serial_inp(up, UART_RX);
		flag = TTY_NORMAL;
		up->port.icount.rx++;

		if (unlikely(*status & (UART_LSR_BI | UART_LSR_PE |
				       UART_LSR_FE | UART_LSR_OE))) {
			/*
			 * For statistics only
			 */
			if (*status & UART_LSR_BI) {
				*status &= ~(UART_LSR_FE | UART_LSR_PE);
				up->port.icount.brk++;
				if (up->port.cons != NULL &&
				    up->port.line == up->port.cons->index)
					saw_console_brk = 1;
				/*
				 * We do the SysRQ and SAK checking
				 * here because otherwise the break
				 * may get masked by ignore_status_mask
				 * or read_status_mask.
				 */
				if (uart_handle_break(&up->port))
					goto ignore_char;
			} else if (*status & UART_LSR_PE)
				up->port.icount.parity++;
			else if (*status & UART_LSR_FE)
				up->port.icount.frame++;
			if (*status & UART_LSR_OE)
				up->port.icount.overrun++;

			/*
			 * Mask off conditions which should be ingored.
			 */
			*status &= up->port.read_status_mask;

			if (up->port.cons != NULL &&
			    up->port.line == up->port.cons->index) {
				/* Recover the break flag from console xmit */
				*status |= up->lsr_break_flag;
				up->lsr_break_flag = 0;
			}

			if (*status & UART_LSR_BI) {
				flag = TTY_BREAK;
			} else if (*status & UART_LSR_PE)
				flag = TTY_PARITY;
			else if (*status & UART_LSR_FE)
				flag = TTY_FRAME;
		}
		if (uart_handle_sysrq_char(&up->port, ch, regs))
			goto ignore_char;
		if ((*status & up->port.ignore_status_mask) == 0)
			tty_insert_flip_char(tty, ch, flag);
		if (*status & UART_LSR_OE)
			/*
			 * Overrun is special, since it's reported
			 * immediately, and doesn't affect the current
			 * character.
			 */
			 tty_insert_flip_char(tty, 0, TTY_OVERRUN);
	ignore_char:
		*status = serial_inp(up, UART_LSR);
	} while ((*status & UART_LSR_DR) && (max_count-- > 0));

	if (saw_console_brk)
		sun_do_break();

	return tty;
}

static void transmit_chars(struct uart_sunsu_port *up)
{
	struct circ_buf *xmit = &up->port.info->xmit;
	int count;

	if (up->port.x_char) {
		serial_outp(up, UART_TX, up->port.x_char);
		up->port.icount.tx++;
		up->port.x_char = 0;
		return;
	}
	if (uart_tx_stopped(&up->port)) {
		sunsu_stop_tx(&up->port);
		return;
	}
	if (uart_circ_empty(xmit)) {
		__stop_tx(up);
		return;
	}

	count = up->port.fifosize;
	do {
		serial_out(up, UART_TX, xmit->buf[xmit->tail]);
		xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
		up->port.icount.tx++;
		if (uart_circ_empty(xmit))
			break;
	} while (--count > 0);

	if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
		uart_write_wakeup(&up->port);

	if (uart_circ_empty(xmit))
		__stop_tx(up);
}

static void check_modem_status(struct uart_sunsu_port *up)
{
	int status;

	status = serial_in(up, UART_MSR);

	if ((status & UART_MSR_ANY_DELTA) == 0)
		return;

	if (status & UART_MSR_TERI)
		up->port.icount.rng++;
	if (status & UART_MSR_DDSR)
		up->port.icount.dsr++;
	if (status & UART_MSR_DDCD)
		uart_handle_dcd_change(&up->port, status & UART_MSR_DCD);
	if (status & UART_MSR_DCTS)
		uart_handle_cts_change(&up->port, status & UART_MSR_CTS);

	wake_up_interruptible(&up->port.info->delta_msr_wait);
}

static irqreturn_t sunsu_serial_interrupt(int irq, void *dev_id, struct pt_regs *regs)
{
	struct uart_sunsu_port *up = dev_id;
	unsigned long flags;
	unsigned char status;

	spin_lock_irqsave(&up->port.lock, flags);

	do {
		struct tty_struct *tty;

		status = serial_inp(up, UART_LSR);
		tty = NULL;
		if (status & UART_LSR_DR)
			tty = receive_chars(up, &status, regs);
		check_modem_status(up);
		if (status & UART_LSR_THRE)
			transmit_chars(up);

		spin_unlock_irqrestore(&up->port.lock, flags);

		if (tty)
			tty_flip_buffer_push(tty);

		spin_lock_irqsave(&up->port.lock, flags);

	} while (!(serial_in(up, UART_IIR) & UART_IIR_NO_INT));

	spin_unlock_irqrestore(&up->port.lock, flags);

	return IRQ_HANDLED;
}

/* Separate interrupt handling path for keyboard/mouse ports.  */

static void
sunsu_change_speed(struct uart_port *port, unsigned int cflag,
		   unsigned int iflag, unsigned int quot);

static void sunsu_change_mouse_baud(struct uart_sunsu_port *up)
{
	unsigned int cur_cflag = up->cflag;
	int quot, new_baud;

	up->cflag &= ~CBAUD;
	up->cflag |= suncore_mouse_baud_cflag_next(cur_cflag, &new_baud);

	quot = up->port.uartclk / (16 * new_baud);

	sunsu_change_speed(&up->port, up->cflag, 0, quot);
}

static void receive_kbd_ms_chars(struct uart_sunsu_port *up, struct pt_regs *regs, int is_break)
{
	do {
		unsigned char ch = serial_inp(up, UART_RX);

		/* Stop-A is handled by drivers/char/keyboard.c now. */
		if (up->su_type == SU_PORT_KBD) {
#ifdef CONFIG_SERIO
			serio_interrupt(up->serio, ch, 0, regs);
#endif
		} else if (up->su_type == SU_PORT_MS) {
			int ret = suncore_mouse_baud_detection(ch, is_break);

			switch (ret) {
			case 2:
				sunsu_change_mouse_baud(up);
				/* fallthru */
			case 1:
				break;

			case 0:
#ifdef CONFIG_SERIO
				serio_interrupt(up->serio, ch, 0, regs);
#endif
				break;
			};
		}
	} while (serial_in(up, UART_LSR) & UART_LSR_DR);
}

static irqreturn_t sunsu_kbd_ms_interrupt(int irq, void *dev_id, struct pt_regs *regs)
{
	struct uart_sunsu_port *up = dev_id;

	if (!(serial_in(up, UART_IIR) & UART_IIR_NO_INT)) {
		unsigned char status = serial_inp(up, UART_LSR);

		if ((status & UART_LSR_DR) || (status & UART_LSR_BI))
			receive_kbd_ms_chars(up, regs,
					     (status & UART_LSR_BI) != 0);
	}

	return IRQ_HANDLED;
}

static unsigned int sunsu_tx_empty(struct uart_port *port)
{
	struct uart_sunsu_port *up = (struct uart_sunsu_port *) port;
	unsigned long flags;
	unsigned int ret;

	spin_lock_irqsave(&up->port.lock, flags);
	ret = serial_in(up, UART_LSR) & UART_LSR_TEMT ? TIOCSER_TEMT : 0;
	spin_unlock_irqrestore(&up->port.lock, flags);

	return ret;
}

static unsigned int sunsu_get_mctrl(struct uart_port *port)
{
	struct uart_sunsu_port *up = (struct uart_sunsu_port *) port;
	unsigned char status;
	unsigned int ret;

	status = serial_in(up, UART_MSR);

	ret = 0;
	if (status & UART_MSR_DCD)
		ret |= TIOCM_CAR;
	if (status & UART_MSR_RI)
		ret |= TIOCM_RNG;
	if (status & UART_MSR_DSR)
		ret |= TIOCM_DSR;
	if (status & UART_MSR_CTS)
		ret |= TIOCM_CTS;
	return ret;
}

static void sunsu_set_mctrl(struct uart_port *port, unsigned int mctrl)
{
	struct uart_sunsu_port *up = (struct uart_sunsu_port *) port;
	unsigned char mcr = 0;

	if (mctrl & TIOCM_RTS)
		mcr |= UART_MCR_RTS;
	if (mctrl & TIOCM_DTR)
		mcr |= UART_MCR_DTR;
	if (mctrl & TIOCM_OUT1)
		mcr |= UART_MCR_OUT1;
	if (mctrl & TIOCM_OUT2)
		mcr |= UART_MCR_OUT2;
	if (mctrl & TIOCM_LOOP)
		mcr |= UART_MCR_LOOP;

	serial_out(up, UART_MCR, mcr);
}

static void sunsu_break_ctl(struct uart_port *port, int break_state)
{
	struct uart_sunsu_port *up = (struct uart_sunsu_port *) port;
	unsigned long flags;

	spin_lock_irqsave(&up->port.lock, flags);
	if (break_state == -1)
		up->lcr |= UART_LCR_SBC;
	else
		up->lcr &= ~UART_LCR_SBC;
	serial_out(up, UART_LCR, up->lcr);
	spin_unlock_irqrestore(&up->port.lock, flags);
}

static int sunsu_startup(struct uart_port *port)
{
	struct uart_sunsu_port *up = (struct uart_sunsu_port *) port;
	unsigned long flags;
	int retval;

	if (up->port.type == PORT_16C950) {
		/* Wake up and initialize UART */
		up->acr = 0;
		serial_outp(up, UART_LCR, 0xBF);
		serial_outp(up, UART_EFR, UART_EFR_ECB);
		serial_outp(up, UART_IER, 0);
		serial_outp(up, UART_LCR, 0);
		serial_icr_write(up, UART_CSR, 0); /* Reset the UART */
		serial_outp(up, UART_LCR, 0xBF);
		serial_outp(up, UART_EFR, UART_EFR_ECB);
		serial_outp(up, UART_LCR, 0);
	}

#ifdef CONFIG_SERIAL_8250_RSA
	/*
	 * If this is an RSA port, see if we can kick it up to the
	 * higher speed clock.
	 */
	enable_rsa(up);
#endif

	/*
	 * Clear the FIFO buffers and disable them.
	 * (they will be reenabled in set_termios())
	 */
	if (uart_config[up->port.type].flags & UART_CLEAR_FIFO) {
		serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO);
		serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO |
				UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT);
		serial_outp(up, UART_FCR, 0);
	}

	/*
	 * Clear the interrupt registers.
	 */
	(void) serial_inp(up, UART_LSR);
	(void) serial_inp(up, UART_RX);
	(void) serial_inp(up, UART_IIR);
	(void) serial_inp(up, UART_MSR);

	/*
	 * At this point, there's no way the LSR could still be 0xff;
	 * if it is, then bail out, because there's likely no UART
	 * here.
	 */
	if (!(up->port.flags & UPF_BUGGY_UART) &&
	    (serial_inp(up, UART_LSR) == 0xff)) {
		printk("ttyS%d: LSR safety check engaged!\n", up->port.line);
		return -ENODEV;
	}

	if (up->su_type != SU_PORT_PORT) {
		retval = request_irq(up->port.irq, sunsu_kbd_ms_interrupt,
				     SA_SHIRQ, su_typev[up->su_type], up);
	} else {
		retval = request_irq(up->port.irq, sunsu_serial_interrupt,
				     SA_SHIRQ, su_typev[up->su_type], up);
	}
	if (retval) {
		printk("su: Cannot register IRQ %d\n", up->port.irq);
		return retval;
	}

	/*
	 * Now, initialize the UART
	 */
	serial_outp(up, UART_LCR, UART_LCR_WLEN8);

	spin_lock_irqsave(&up->port.lock, flags);

	up->port.mctrl |= TIOCM_OUT2;

	sunsu_set_mctrl(&up->port, up->port.mctrl);
	spin_unlock_irqrestore(&up->port.lock, flags);

	/*
	 * Finally, enable interrupts.  Note: Modem status interrupts
	 * are set via set_termios(), which will be occurring imminently
	 * anyway, so we don't enable them here.
	 */
	up->ier = UART_IER_RLSI | UART_IER_RDI;
	serial_outp(up, UART_IER, up->ier);

	if (up->port.flags & UPF_FOURPORT) {
		unsigned int icp;
		/*
		 * Enable interrupts on the AST Fourport board
		 */
		icp = (up->port.iobase & 0xfe0) | 0x01f;
		outb_p(0x80, icp);
		(void) inb_p(icp);
	}

	/*
	 * And clear the interrupt registers again for luck.
	 */
	(void) serial_inp(up, UART_LSR);
	(void) serial_inp(up, UART_RX);
	(void) serial_inp(up, UART_IIR);
	(void) serial_inp(up, UART_MSR);

	return 0;
}

static void sunsu_shutdown(struct uart_port *port)
{
	struct uart_sunsu_port *up = (struct uart_sunsu_port *) port;
	unsigned long flags;

	/*
	 * Disable interrupts from this port
	 */
	up->ier = 0;
	serial_outp(up, UART_IER, 0);

	spin_lock_irqsave(&up->port.lock, flags);
	if (up->port.flags & UPF_FOURPORT) {
		/* reset interrupts on the AST Fourport board */
		inb((up->port.iobase & 0xfe0) | 0x1f);
		up->port.mctrl |= TIOCM_OUT1;
	} else
		up->port.mctrl &= ~TIOCM_OUT2;

	sunsu_set_mctrl(&up->port, up->port.mctrl);
	spin_unlock_irqrestore(&up->port.lock, flags);

	/*
	 * Disable break condition and FIFOs
	 */
	serial_out(up, UART_LCR, serial_inp(up, UART_LCR) & ~UART_LCR_SBC);
	serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO |
				  UART_FCR_CLEAR_RCVR |
				  UART_FCR_CLEAR_XMIT);
	serial_outp(up, UART_FCR, 0);

#ifdef CONFIG_SERIAL_8250_RSA
	/*
	 * Reset the RSA board back to 115kbps compat mode.
	 */
	disable_rsa(up);
#endif

	/*
	 * Read data port to reset things.
	 */
	(void) serial_in(up, UART_RX);

	free_irq(up->port.irq, up);
}

static void
sunsu_change_speed(struct uart_port *port, unsigned int cflag,
		   unsigned int iflag, unsigned int quot)
{
	struct uart_sunsu_port *up = (struct uart_sunsu_port *) port;
	unsigned char cval, fcr = 0;
	unsigned long flags;

	switch (cflag & CSIZE) {
	case CS5:
		cval = 0x00;
		break;
	case CS6:
		cval = 0x01;
		break;
	case CS7:
		cval = 0x02;
		break;
	default:
	case CS8:
		cval = 0x03;
		break;
	}

	if (cflag & CSTOPB)
		cval |= 0x04;
	if (cflag & PARENB)
		cval |= UART_LCR_PARITY;
	if (!(cflag & PARODD))
		cval |= UART_LCR_EPAR;
#ifdef CMSPAR
	if (cflag & CMSPAR)
		cval |= UART_LCR_SPAR;
#endif

	/*
	 * Work around a bug in the Oxford Semiconductor 952 rev B
	 * chip which causes it to seriously miscalculate baud rates
	 * when DLL is 0.
	 */
	if ((quot & 0xff) == 0 && up->port.type == PORT_16C950 &&
	    up->rev == 0x5201)
		quot ++;

	if (uart_config[up->port.type].flags & UART_USE_FIFO) {
		if ((up->port.uartclk / quot) < (2400 * 16))
			fcr = UART_FCR_ENABLE_FIFO | UART_FCR_TRIGGER_1;
#ifdef CONFIG_SERIAL_8250_RSA
		else if (up->port.type == PORT_RSA)
			fcr = UART_FCR_ENABLE_FIFO | UART_FCR_TRIGGER_14;
#endif
		else
			fcr = UART_FCR_ENABLE_FIFO | UART_FCR_TRIGGER_8;
	}
	if (up->port.type == PORT_16750)
		fcr |= UART_FCR7_64BYTE;

	/*
	 * Ok, we're now changing the port state.  Do it with
	 * interrupts disabled.
	 */
	spin_lock_irqsave(&up->port.lock, flags);

	/*
	 * Update the per-port timeout.
	 */
	uart_update_timeout(port, cflag, (port->uartclk / (16 * quot)));

	up->port.read_status_mask = UART_LSR_OE | UART_LSR_THRE | UART_LSR_DR;
	if (iflag & INPCK)
		up->port.read_status_mask |= UART_LSR_FE | UART_LSR_PE;
	if (iflag & (BRKINT | PARMRK))
		up->port.read_status_mask |= UART_LSR_BI;

	/*
	 * Characteres to ignore
	 */
	up->port.ignore_status_mask = 0;
	if (iflag & IGNPAR)
		up->port.ignore_status_mask |= UART_LSR_PE | UART_LSR_FE;
	if (iflag & IGNBRK) {
		up->port.ignore_status_mask |= UART_LSR_BI;
		/*
		 * If we're ignoring parity and break indicators,
		 * ignore overruns too (for real raw support).
		 */
		if (iflag & IGNPAR)
			up->port.ignore_status_mask |= UART_LSR_OE;
	}

	/*
	 * ignore all characters if CREAD is not set
	 */
	if ((cflag & CREAD) == 0)
		up->port.ignore_status_mask |= UART_LSR_DR;

	/*
	 * CTS flow control flag and modem status interrupts
	 */
	up->ier &= ~UART_IER_MSI;
	if (UART_ENABLE_MS(&up->port, cflag))
		up->ier |= UART_IER_MSI;

	serial_out(up, UART_IER, up->ier);

	if (uart_config[up->port.type].flags & UART_STARTECH) {
		serial_outp(up, UART_LCR, 0xBF);
		serial_outp(up, UART_EFR, cflag & CRTSCTS ? UART_EFR_CTS :0);
	}
	serial_outp(up, UART_LCR, cval | UART_LCR_DLAB);/* set DLAB */
	serial_outp(up, UART_DLL, quot & 0xff);		/* LS of divisor */
	serial_outp(up, UART_DLM, quot >> 8);		/* MS of divisor */
	if (up->port.type == PORT_16750)
		serial_outp(up, UART_FCR, fcr);		/* set fcr */
	serial_outp(up, UART_LCR, cval);		/* reset DLAB */
	up->lcr = cval;					/* Save LCR */
	if (up->port.type != PORT_16750) {
		if (fcr & UART_FCR_ENABLE_FIFO) {
			/* emulated UARTs (Lucent Venus 167x) need two steps */
			serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO);
		}
		serial_outp(up, UART_FCR, fcr);		/* set fcr */
	}

	up->cflag = cflag;

	spin_unlock_irqrestore(&up->port.lock, flags);
}

static void
sunsu_set_termios(struct uart_port *port, struct termios *termios,
		  struct termios *old)
{
	unsigned int baud, quot;

	/*
	 * Ask the core to calculate the divisor for us.
	 */
	baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk/16); 
	quot = uart_get_divisor(port, baud);

	sunsu_change_speed(port, termios->c_cflag, termios->c_iflag, quot);
}

static void sunsu_release_port(struct uart_port *port)
{
}

static int sunsu_request_port(struct uart_port *port)
{
	return 0;
}

static void sunsu_config_port(struct uart_port *port, int flags)
{
	struct uart_sunsu_port *up = (struct uart_sunsu_port *) port;

	if (flags & UART_CONFIG_TYPE) {
		/*
		 * We are supposed to call autoconfig here, but this requires
		 * splitting all the OBP probing crap from the UART probing.
		 * We'll do it when we kill sunsu.c altogether.
		 */
		port->type = up->type_probed;	/* XXX */
	}
}

static int
sunsu_verify_port(struct uart_port *port, struct serial_struct *ser)
{
	return -EINVAL;
}

static const char *
sunsu_type(struct uart_port *port)
{
	int type = port->type;

	if (type >= ARRAY_SIZE(uart_config))
		type = 0;
	return uart_config[type].name;
}

static struct uart_ops sunsu_pops = {
	.tx_empty	= sunsu_tx_empty,
	.set_mctrl	= sunsu_set_mctrl,
	.get_mctrl	= sunsu_get_mctrl,
	.stop_tx	= sunsu_stop_tx,
	.start_tx	= sunsu_start_tx,
	.stop_rx	= sunsu_stop_rx,
	.enable_ms	= sunsu_enable_ms,
	.break_ctl	= sunsu_break_ctl,
	.startup	= sunsu_startup,
	.shutdown	= sunsu_shutdown,
	.set_termios	= sunsu_set_termios,
	.type		= sunsu_type,
	.release_port	= sunsu_release_port,
	.request_port	= sunsu_request_port,
	.config_port	= sunsu_config_port,
	.verify_port	= sunsu_verify_port,
};

#define UART_NR	4

static struct uart_sunsu_port sunsu_ports[UART_NR];

#ifdef CONFIG_SERIO

static DEFINE_SPINLOCK(sunsu_serio_lock);

static int sunsu_serio_write(struct serio *serio, unsigned char ch)
{
	struct uart_sunsu_port *up = serio->port_data;
	unsigned long flags;
	int lsr;

	spin_lock_irqsave(&sunsu_serio_lock, flags);

	do {
		lsr = serial_in(up, UART_LSR);
	} while (!(lsr & UART_LSR_THRE));

	/* Send the character out. */
	serial_out(up, UART_TX, ch);

	spin_unlock_irqrestore(&sunsu_serio_lock, flags);

	return 0;
}

static int sunsu_serio_open(struct serio *serio)
{
	struct uart_sunsu_port *up = serio->port_data;
	unsigned long flags;
	int ret;

	spin_lock_irqsave(&sunsu_serio_lock, flags);
	if (!up->serio_open) {
		up->serio_open = 1;
		ret = 0;
	} else
		ret = -EBUSY;
	spin_unlock_irqrestore(&sunsu_serio_lock, flags);

	return ret;
}

static void sunsu_serio_close(struct serio *serio)
{
	struct uart_sunsu_port *up = serio->port_data;
	unsigned long flags;

	spin_lock_irqsave(&sunsu_serio_lock, flags);
	up->serio_open = 0;
	spin_unlock_irqrestore(&sunsu_serio_lock, flags);
}

#endif /* CONFIG_SERIO */

static void sunsu_autoconfig(struct uart_sunsu_port *up)
{
	unsigned char status1, status2, scratch, scratch2, scratch3;
	unsigned char save_lcr, save_mcr;
	struct linux_ebus_device *dev = NULL;
	struct linux_ebus *ebus;
#ifdef CONFIG_SPARC64
	struct sparc_isa_bridge *isa_br;
	struct sparc_isa_device *isa_dev;
#endif
#ifndef CONFIG_SPARC64
	struct linux_prom_registers reg0;
#endif
	unsigned long flags;

	if (!up->port_node || !up->su_type)
		return;

	up->type_probed = PORT_UNKNOWN;
	up->port.iotype = UPIO_MEM;

	/*
	 * First we look for Ebus-bases su's
	 */
	for_each_ebus(ebus) {
		for_each_ebusdev(dev, ebus) {
			if (dev->prom_node->node == up->port_node) {
				/*
				 * The EBus is broken on sparc; it delivers
				 * virtual addresses in resources. Oh well...
				 * This is correct on sparc64, though.
				 */
				up->port.membase = (char *) dev->resource[0].start;
				/*
				 * This is correct on both architectures.
				 */
				up->port.mapbase = dev->resource[0].start;
				up->port.irq = dev->irqs[0];
				goto ebus_done;
			}
		}
	}

#ifdef CONFIG_SPARC64
	for_each_isa(isa_br) {
		for_each_isadev(isa_dev, isa_br) {
			if (isa_dev->prom_node->node == up->port_node) {
				/* Same on sparc64. Cool architecure... */
				up->port.membase = (char *) isa_dev->resource.start;
				up->port.mapbase = isa_dev->resource.start;
				up->port.irq = isa_dev->irq;
				goto ebus_done;
			}
		}
	}
#endif

#ifdef CONFIG_SPARC64
	/*
	 * Not on Ebus, bailing.
	 */
	return;
#else
	/*
	 * Not on Ebus, must be OBIO.
	 */
	if (prom_getproperty(up->port_node, "reg",
			     (char *)&reg0, sizeof(reg0)) == -1) {
		prom_printf("sunsu: no \"reg\" property\n");
		return;
	}
	prom_apply_obio_ranges(&reg0, 1);
	if (reg0.which_io != 0) {	/* Just in case... */
		prom_printf("sunsu: bus number nonzero: 0x%x:%x\n",
		    reg0.which_io, reg0.phys_addr);
		return;
	}
	up->port.mapbase = reg0.phys_addr;
	if ((up->port.membase = ioremap(reg0.phys_addr, reg0.reg_size)) == 0) {
		prom_printf("sunsu: Cannot map registers.\n");
		return;
	}

	/*
	 * 0x20 is sun4m thing, Dave Redman heritage.
	 * See arch/sparc/kernel/irq.c.
	 */
#define IRQ_4M(n)	((n)|0x20)

	/*
	 * There is no intr property on MrCoffee, so hardwire it.
	 */
	up->port.irq = IRQ_4M(13);
#endif

ebus_done:

	spin_lock_irqsave(&up->port.lock, flags);

	if (!(up->port.flags & UPF_BUGGY_UART)) {
		/*
		 * Do a simple existence test first; if we fail this, there's
		 * no point trying anything else.
		 *
		 * 0x80 is used as a nonsense port to prevent against false
		 * positives due to ISA bus float.  The assumption is that
		 * 0x80 is a non-existent port; which should be safe since
		 * include/asm/io.h also makes this assumption.
		 */
		scratch = serial_inp(up, UART_IER);
		serial_outp(up, UART_IER, 0);
#ifdef __i386__
		outb(0xff, 0x080);
#endif
		scratch2 = serial_inp(up, UART_IER);
		serial_outp(up, UART_IER, 0x0f);
#ifdef __i386__
		outb(0, 0x080);
#endif
		scratch3 = serial_inp(up, UART_IER);
		serial_outp(up, UART_IER, scratch);
		if (scratch2 != 0 || scratch3 != 0x0F)
			goto out;	/* We failed; there's nothing here */
	}

	save_mcr = serial_in(up, UART_MCR);
	save_lcr = serial_in(up, UART_LCR);

	/* 
	 * Check to see if a UART is really there.  Certain broken
	 * internal modems based on the Rockwell chipset fail this
	 * test, because they apparently don't implement the loopback
	 * test mode.  So this test is skipped on the COM 1 through
	 * COM 4 ports.  This *should* be safe, since no board
	 * manufacturer would be stupid enough to design a board
	 * that conflicts with COM 1-4 --- we hope!
	 */
	if (!(up->port.flags & UPF_SKIP_TEST)) {
		serial_outp(up, UART_MCR, UART_MCR_LOOP | 0x0A);
		status1 = serial_inp(up, UART_MSR) & 0xF0;
		serial_outp(up, UART_MCR, save_mcr);
		if (status1 != 0x90)
			goto out;	/* We failed loopback test */
	}
	serial_outp(up, UART_LCR, 0xBF);	/* set up for StarTech test */
	serial_outp(up, UART_EFR, 0);		/* EFR is the same as FCR */
	serial_outp(up, UART_LCR, 0);
	serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO);
	scratch = serial_in(up, UART_IIR) >> 6;
	switch (scratch) {
		case 0:
			up->port.type = PORT_16450;
			break;
		case 1:
			up->port.type = PORT_UNKNOWN;
			break;
		case 2:
			up->port.type = PORT_16550;
			break;
		case 3:
			up->port.type = PORT_16550A;
			break;
	}
	if (up->port.type == PORT_16550A) {
		/* Check for Startech UART's */
		serial_outp(up, UART_LCR, UART_LCR_DLAB);
		if (serial_in(up, UART_EFR) == 0) {
			up->port.type = PORT_16650;
		} else {
			serial_outp(up, UART_LCR, 0xBF);
			if (serial_in(up, UART_EFR) == 0)
				up->port.type = PORT_16650V2;
		}
	}
	if (up->port.type == PORT_16550A) {
		/* Check for TI 16750 */
		serial_outp(up, UART_LCR, save_lcr | UART_LCR_DLAB);
		serial_outp(up, UART_FCR,
			    UART_FCR_ENABLE_FIFO | UART_FCR7_64BYTE);
		scratch = serial_in(up, UART_IIR) >> 5;
		if (scratch == 7) {
			/*
			 * If this is a 16750, and not a cheap UART
			 * clone, then it should only go into 64 byte
			 * mode if the UART_FCR7_64BYTE bit was set
			 * while UART_LCR_DLAB was latched.
			 */
 			serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO);
			serial_outp(up, UART_LCR, 0);
			serial_outp(up, UART_FCR,
				    UART_FCR_ENABLE_FIFO | UART_FCR7_64BYTE);
			scratch = serial_in(up, UART_IIR) >> 5;
			if (scratch == 6)
				up->port.type = PORT_16750;
		}
		serial_outp(up, UART_FCR, UART_FCR_ENABLE_FIFO);
	}
	serial_outp(up, UART_LCR, save_lcr);
	if (up->port.type == PORT_16450) {
		scratch = serial_in(up, UART_SCR);
		serial_outp(up, UART_SCR, 0xa5);
		status1 = serial_in(up, UART_SCR);
		serial_outp(up, UART_SCR, 0x5a);
		status2 = serial_in(up, UART_SCR);
		serial_outp(up, UART_SCR, scratch);

		if ((status1 != 0xa5) || (status2 != 0x5a))
			up->port.type = PORT_8250;
	}

	up->port.fifosize = uart_config[up->port.type].dfl_xmit_fifo_size;

	if (up->port.type == PORT_UNKNOWN)
		goto out;
	up->type_probed = up->port.type;	/* XXX */

	/*
	 * Reset the UART.
	 */
#ifdef CONFIG_SERIAL_8250_RSA
	if (up->port.type == PORT_RSA)
		serial_outp(up, UART_RSA_FRR, 0);
#endif
	serial_outp(up, UART_MCR, save_mcr);
	serial_outp(up, UART_FCR, (UART_FCR_ENABLE_FIFO |
				     UART_FCR_CLEAR_RCVR |
				     UART_FCR_CLEAR_XMIT));
	serial_outp(up, UART_FCR, 0);
	(void)serial_in(up, UART_RX);
	serial_outp(up, UART_IER, 0);

out:
	spin_unlock_irqrestore(&up->port.lock, flags);
}

static struct uart_driver sunsu_reg = {
	.owner			= THIS_MODULE,
	.driver_name		= "serial",
	.dev_name		= "ttyS",
	.major			= TTY_MAJOR,
};

static int __init sunsu_kbd_ms_init(struct uart_sunsu_port *up, int channel)
{
	int quot, baud;
#ifdef CONFIG_SERIO
	struct serio *serio;
#endif

	spin_lock_init(&up->port.lock);
	up->port.line = channel;
	up->port.type = PORT_UNKNOWN;
	up->port.uartclk = (SU_BASE_BAUD * 16);

	if (up->su_type == SU_PORT_KBD) {
		up->cflag = B1200 | CS8 | CLOCAL | CREAD;
		baud = 1200;
	} else {
		up->cflag = B4800 | CS8 | CLOCAL | CREAD;
		baud = 4800;
	}
	quot = up->port.uartclk / (16 * baud);

	sunsu_autoconfig(up);
	if (up->port.type == PORT_UNKNOWN)
		return -1;

	printk(KERN_INFO "su%d at 0x%p (irq = %d) is a %s\n",
	       channel,
	       up->port.membase, up->port.irq,
	       sunsu_type(&up->port));

#ifdef CONFIG_SERIO
	up->serio = serio = kmalloc(sizeof(struct serio), GFP_KERNEL);
	if (serio) {
		memset(serio, 0, sizeof(*serio));

		serio->port_data = up;

		serio->id.type = SERIO_RS232;
		if (up->su_type == SU_PORT_KBD) {
			serio->id.proto = SERIO_SUNKBD;
			strlcpy(serio->name, "sukbd", sizeof(serio->name));
		} else {
			serio->id.proto = SERIO_SUN;
			serio->id.extra = 1;
			strlcpy(serio->name, "sums", sizeof(serio->name));
		}
		strlcpy(serio->phys, (channel == 0 ? "su/serio0" : "su/serio1"),
			sizeof(serio->phys));

		serio->write = sunsu_serio_write;
		serio->open = sunsu_serio_open;
		serio->close = sunsu_serio_close;

		serio_register_port(serio);
	} else {
		printk(KERN_WARNING "su%d: not enough memory for serio port\n",
			channel);
	}
#endif

	sunsu_change_speed(&up->port, up->cflag, 0, quot);

	sunsu_startup(&up->port);
	return 0;
}

/*
 * ------------------------------------------------------------
 * Serial console driver
 * ------------------------------------------------------------
 */

#ifdef CONFIG_SERIAL_SUNSU_CONSOLE

#define BOTH_EMPTY (UART_LSR_TEMT | UART_LSR_THRE)

/*
 *	Wait for transmitter & holding register to empty
 */
static __inline__ void wait_for_xmitr(struct uart_sunsu_port *up)
{
	unsigned int status, tmout = 10000;

	/* Wait up to 10ms for the character(s) to be sent. */
	do {
		status = serial_in(up, UART_LSR);

		if (status & UART_LSR_BI)
			up->lsr_break_flag = UART_LSR_BI;

		if (--tmout == 0)
			break;
		udelay(1);
	} while ((status & BOTH_EMPTY) != BOTH_EMPTY);

	/* Wait up to 1s for flow control if necessary */
	if (up->port.flags & UPF_CONS_FLOW) {
		tmout = 1000000;
		while (--tmout &&
		       ((serial_in(up, UART_MSR) & UART_MSR_CTS) == 0))
			udelay(1);
	}
}

static void sunsu_console_putchar(struct uart_port *port, int ch)
{
	struct uart_sunsu_port *up = (struct uart_sunsu_port *)port;

	wait_for_xmitr(up);
	serial_out(up, UART_TX, ch);
}

/*
 *	Print a string to the serial port trying not to disturb
 *	any possible real use of the port...
 */
static void sunsu_console_write(struct console *co, const char *s,
				unsigned int count)
{
	struct uart_sunsu_port *up = &sunsu_ports[co->index];
	unsigned int ier;

	/*
	 *	First save the UER then disable the interrupts
	 */
	ier = serial_in(up, UART_IER);
	serial_out(up, UART_IER, 0);

	uart_console_write(&up->port, s, count, sunsu_console_putchar);

	/*
	 *	Finally, wait for transmitter to become empty
	 *	and restore the IER
	 */
	wait_for_xmitr(up);
	serial_out(up, UART_IER, ier);
}

/*
 *	Setup initial baud/bits/parity. We do two things here:
 *	- construct a cflag setting for the first su_open()
 *	- initialize the serial port
 *	Return non-zero if we didn't find a serial port.
 */
static int sunsu_console_setup(struct console *co, char *options)
{
	struct uart_port *port;
	int baud = 9600;
	int bits = 8;
	int parity = 'n';
	int flow = 'n';

	printk("Console: ttyS%d (SU)\n",
	       (sunsu_reg.minor - 64) + co->index);

	/*
	 * Check whether an invalid uart number has been specified, and
	 * if so, search for the first available port that does have
	 * console support.
	 */
	if (co->index >= UART_NR)
		co->index = 0;
	port = &sunsu_ports[co->index].port;

	/*
	 * Temporary fix.
	 */
	spin_lock_init(&port->lock);

	if (options)
		uart_parse_options(options, &baud, &parity, &bits, &flow);

	return uart_set_options(port, co, baud, parity, bits, flow);
}

static struct console sunsu_cons = {
	.name	=	"ttyS",
	.write	=	sunsu_console_write,
	.device	=	uart_console_device,
	.setup	=	sunsu_console_setup,
	.flags	=	CON_PRINTBUFFER,
	.index	=	-1,
	.data	=	&sunsu_reg,
};

/*
 *	Register console.
 */

static inline struct console *SUNSU_CONSOLE(void)
{
	int i;

	if (con_is_present())
		return NULL;

	for (i = 0; i < UART_NR; i++) {
		int this_minor = sunsu_reg.minor + i;

		if ((this_minor - 64) == (serial_console - 1))
			break;
	}
	if (i == UART_NR)
		return NULL;
	if (sunsu_ports[i].port_node == 0)
		return NULL;

	sunsu_cons.index = i;

	return &sunsu_cons;
}
#else
#define SUNSU_CONSOLE()			(NULL)
#define sunsu_serial_console_init()	do { } while (0)
#endif

static int __init sunsu_serial_init(void)
{
	int instance, ret, i;

	/* How many instances do we need?  */
	instance = 0;
	for (i = 0; i < UART_NR; i++) {
		struct uart_sunsu_port *up = &sunsu_ports[i];

		if (up->su_type == SU_PORT_MS ||
		    up->su_type == SU_PORT_KBD)
			continue;

		spin_lock_init(&up->port.lock);
		up->port.flags |= UPF_BOOT_AUTOCONF;
		up->port.type = PORT_UNKNOWN;
		up->port.uartclk = (SU_BASE_BAUD * 16);

		sunsu_autoconfig(up);
		if (up->port.type == PORT_UNKNOWN)
			continue;

		up->port.line = instance++;
		up->port.ops = &sunsu_pops;
	}

	sunsu_reg.minor = sunserial_current_minor;

	sunsu_reg.nr = instance;

	ret = uart_register_driver(&sunsu_reg);
	if (ret < 0)
		return ret;

	sunsu_reg.tty_driver->name_base = sunsu_reg.minor - 64;

	sunserial_current_minor += instance;

	sunsu_reg.cons = SUNSU_CONSOLE();

	for (i = 0; i < UART_NR; i++) {
		struct uart_sunsu_port *up = &sunsu_ports[i];

		/* Do not register Keyboard/Mouse lines with UART
		 * layer.
		 */
		if (up->su_type == SU_PORT_MS ||
		    up->su_type == SU_PORT_KBD)
			continue;

		if (up->port.type == PORT_UNKNOWN)
			continue;

		uart_add_one_port(&sunsu_reg, &up->port);
	}

	return 0;
}

static int su_node_ok(int node, char *name, int namelen)
{
	if (strncmp(name, "su", namelen) == 0 ||
	    strncmp(name, "su_pnp", namelen) == 0)
		return 1;

	if (strncmp(name, "serial", namelen) == 0) {
		char compat[32];
		int clen;

		/* Is it _really_ a 'su' device? */
		clen = prom_getproperty(node, "compatible", compat, sizeof(compat));
		if (clen > 0) {
			if (strncmp(compat, "sab82532", 8) == 0) {
				/* Nope, Siemens serial, not for us. */
				return 0;
			}
		}
		return 1;
	}

	return 0;
}

#define SU_PROPSIZE	128

/*
 * Scan status structure.
 * "prop" is a local variable but it eats stack to keep it in each
 * stack frame of a recursive procedure.
 */
struct su_probe_scan {
	int msnode, kbnode;	/* PROM nodes for mouse and keyboard */
	int msx, kbx;		/* minors for mouse and keyboard */
	int devices;		/* scan index */
	char prop[SU_PROPSIZE];
};

/*
 * We have several platforms which present 'su' in different parts
 * of the device tree. 'su' may be found under obio, ebus, isa and pci.
 * We walk over the tree and find them wherever PROM hides them.
 */
static void __init su_probe_any(struct su_probe_scan *t, int sunode)
{
	struct uart_sunsu_port *up;
	int len;

	if (t->devices >= UART_NR)
		return;

	for (; sunode != 0; sunode = prom_getsibling(sunode)) {
		len = prom_getproperty(sunode, "name", t->prop, SU_PROPSIZE);
		if (len <= 1)
			continue;		/* Broken PROM node */

		if (su_node_ok(sunode, t->prop, len)) {
			up = &sunsu_ports[t->devices];
			if (t->kbnode != 0 && sunode == t->kbnode) {
				t->kbx = t->devices;
				up->su_type = SU_PORT_KBD;
			} else if (t->msnode != 0 && sunode == t->msnode) {
				t->msx = t->devices;
				up->su_type = SU_PORT_MS;
			} else {
#ifdef CONFIG_SPARC64
				/*
				 * Do not attempt to use the truncated
				 * keyboard/mouse ports as serial ports
				 * on Ultras with PC keyboard attached.
				 */
				if (prom_getbool(sunode, "mouse"))
					continue;
				if (prom_getbool(sunode, "keyboard"))
					continue;
#endif
				up->su_type = SU_PORT_PORT;
			}
			up->port_node = sunode;
			++t->devices;
		} else {
			su_probe_any(t, prom_getchild(sunode));
		}
	}
}

static int __init sunsu_probe(void)
{
	int node;
	int len;
	struct su_probe_scan scan;

	/*
	 * First, we scan the tree.
	 */
	scan.devices = 0;
	scan.msx = -1;
	scan.kbx = -1;
	scan.kbnode = 0;
	scan.msnode = 0;

	/*
	 * Get the nodes for keyboard and mouse from 'aliases'...
	 */
        node = prom_getchild(prom_root_node);
	node = prom_searchsiblings(node, "aliases");
	if (node != 0) {
		len = prom_getproperty(node, "keyboard", scan.prop, SU_PROPSIZE);
		if (len > 0) {
			scan.prop[len] = 0;
			scan.kbnode = prom_finddevice(scan.prop);
		}

		len = prom_getproperty(node, "mouse", scan.prop, SU_PROPSIZE);
		if (len > 0) {
			scan.prop[len] = 0;
			scan.msnode = prom_finddevice(scan.prop);
		}
	}

	su_probe_any(&scan, prom_getchild(prom_root_node));

	/*
	 * Second, we process the special case of keyboard and mouse.
	 *
	 * Currently if we got keyboard and mouse hooked to "su" ports
	 * we do not use any possible remaining "su" as a serial port.
	 * Thus, we ignore values of .msx and .kbx, then compact ports.
	 */
	if (scan.msx != -1 && scan.kbx != -1) {
		sunsu_ports[0].su_type = SU_PORT_MS;
		sunsu_ports[0].port_node = scan.msnode;
		sunsu_kbd_ms_init(&sunsu_ports[0], 0);

		sunsu_ports[1].su_type = SU_PORT_KBD;
		sunsu_ports[1].port_node = scan.kbnode;
		sunsu_kbd_ms_init(&sunsu_ports[1], 1);

		return 0;
	}

	if (scan.msx != -1 || scan.kbx != -1) {
		printk("sunsu_probe: cannot match keyboard and mouse, confused\n");
		return -ENODEV;
	}

	if (scan.devices == 0)
		return -ENODEV;

	/*
	 * Console must be initiated after the generic initialization.
	 */
       	sunsu_serial_init();

	return 0;
}

static void __exit sunsu_exit(void)
{
	int i, saw_uart;

	saw_uart = 0;
	for (i = 0; i < UART_NR; i++) {
		struct uart_sunsu_port *up = &sunsu_ports[i];

		if (up->su_type == SU_PORT_MS ||
		    up->su_type == SU_PORT_KBD) {
#ifdef CONFIG_SERIO
			if (up->serio) {
				serio_unregister_port(up->serio);
				up->serio = NULL;
			}
#endif
		} else if (up->port.type != PORT_UNKNOWN) {
			uart_remove_one_port(&sunsu_reg, &up->port);
			saw_uart++;
		}
	}

	if (saw_uart)
		uart_unregister_driver(&sunsu_reg);
}

module_init(sunsu_probe);
module_exit(sunsu_exit);
MODULE_LICENSE("GPL");