| // SPDX-License-Identifier: GPL-2.0 OR MIT |
| /* |
| * Copyright 2015 Endless Mobile, Inc. |
| * Author: Carlo Caione <carlo@endlessm.com> |
| */ |
| |
| #include <dt-bindings/clock/meson8-ddr-clkc.h> |
| #include <dt-bindings/clock/meson8b-clkc.h> |
| #include <dt-bindings/gpio/meson8b-gpio.h> |
| #include <dt-bindings/power/meson8-power.h> |
| #include <dt-bindings/reset/amlogic,meson8b-reset.h> |
| #include <dt-bindings/reset/amlogic,meson8b-clkc-reset.h> |
| #include <dt-bindings/thermal/thermal.h> |
| #include "meson.dtsi" |
| |
| / { |
| cpus { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| cpu0: cpu@200 { |
| device_type = "cpu"; |
| compatible = "arm,cortex-a5"; |
| next-level-cache = <&L2>; |
| reg = <0x200>; |
| enable-method = "amlogic,meson8b-smp"; |
| resets = <&clkc CLKC_RESET_CPU0_SOFT_RESET>; |
| operating-points-v2 = <&cpu_opp_table>; |
| clocks = <&clkc CLKID_CPUCLK>; |
| #cooling-cells = <2>; /* min followed by max */ |
| }; |
| |
| cpu1: cpu@201 { |
| device_type = "cpu"; |
| compatible = "arm,cortex-a5"; |
| next-level-cache = <&L2>; |
| reg = <0x201>; |
| enable-method = "amlogic,meson8b-smp"; |
| resets = <&clkc CLKC_RESET_CPU1_SOFT_RESET>; |
| operating-points-v2 = <&cpu_opp_table>; |
| clocks = <&clkc CLKID_CPUCLK>; |
| #cooling-cells = <2>; /* min followed by max */ |
| }; |
| |
| cpu2: cpu@202 { |
| device_type = "cpu"; |
| compatible = "arm,cortex-a5"; |
| next-level-cache = <&L2>; |
| reg = <0x202>; |
| enable-method = "amlogic,meson8b-smp"; |
| resets = <&clkc CLKC_RESET_CPU2_SOFT_RESET>; |
| operating-points-v2 = <&cpu_opp_table>; |
| clocks = <&clkc CLKID_CPUCLK>; |
| #cooling-cells = <2>; /* min followed by max */ |
| }; |
| |
| cpu3: cpu@203 { |
| device_type = "cpu"; |
| compatible = "arm,cortex-a5"; |
| next-level-cache = <&L2>; |
| reg = <0x203>; |
| enable-method = "amlogic,meson8b-smp"; |
| resets = <&clkc CLKC_RESET_CPU3_SOFT_RESET>; |
| operating-points-v2 = <&cpu_opp_table>; |
| clocks = <&clkc CLKID_CPUCLK>; |
| #cooling-cells = <2>; /* min followed by max */ |
| }; |
| }; |
| |
| cpu_opp_table: opp-table { |
| compatible = "operating-points-v2"; |
| opp-shared; |
| |
| opp-96000000 { |
| opp-hz = /bits/ 64 <96000000>; |
| opp-microvolt = <860000>; |
| }; |
| opp-192000000 { |
| opp-hz = /bits/ 64 <192000000>; |
| opp-microvolt = <860000>; |
| }; |
| opp-312000000 { |
| opp-hz = /bits/ 64 <312000000>; |
| opp-microvolt = <860000>; |
| }; |
| opp-408000000 { |
| opp-hz = /bits/ 64 <408000000>; |
| opp-microvolt = <860000>; |
| }; |
| opp-504000000 { |
| opp-hz = /bits/ 64 <504000000>; |
| opp-microvolt = <860000>; |
| }; |
| opp-600000000 { |
| opp-hz = /bits/ 64 <600000000>; |
| opp-microvolt = <860000>; |
| }; |
| opp-720000000 { |
| opp-hz = /bits/ 64 <720000000>; |
| opp-microvolt = <860000>; |
| }; |
| opp-816000000 { |
| opp-hz = /bits/ 64 <816000000>; |
| opp-microvolt = <900000>; |
| }; |
| opp-1008000000 { |
| opp-hz = /bits/ 64 <1008000000>; |
| opp-microvolt = <1140000>; |
| }; |
| opp-1200000000 { |
| opp-hz = /bits/ 64 <1200000000>; |
| opp-microvolt = <1140000>; |
| }; |
| opp-1320000000 { |
| opp-hz = /bits/ 64 <1320000000>; |
| opp-microvolt = <1140000>; |
| }; |
| opp-1488000000 { |
| opp-hz = /bits/ 64 <1488000000>; |
| opp-microvolt = <1140000>; |
| }; |
| opp-1536000000 { |
| opp-hz = /bits/ 64 <1536000000>; |
| opp-microvolt = <1140000>; |
| }; |
| }; |
| |
| gpu_opp_table: gpu-opp-table { |
| compatible = "operating-points-v2"; |
| |
| opp-255000000 { |
| opp-hz = /bits/ 64 <255000000>; |
| opp-microvolt = <1100000>; |
| }; |
| opp-364285714 { |
| opp-hz = /bits/ 64 <364285714>; |
| opp-microvolt = <1100000>; |
| }; |
| opp-425000000 { |
| opp-hz = /bits/ 64 <425000000>; |
| opp-microvolt = <1100000>; |
| }; |
| opp-510000000 { |
| opp-hz = /bits/ 64 <510000000>; |
| opp-microvolt = <1100000>; |
| }; |
| opp-637500000 { |
| opp-hz = /bits/ 64 <637500000>; |
| opp-microvolt = <1100000>; |
| turbo-mode; |
| }; |
| }; |
| |
| pmu { |
| compatible = "arm,cortex-a5-pmu"; |
| interrupts = <GIC_SPI 137 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 153 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-affinity = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>; |
| }; |
| |
| reserved-memory { |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges; |
| |
| /* 2 MiB reserved for Hardware ROM Firmware? */ |
| hwrom@0 { |
| reg = <0x0 0x200000>; |
| no-map; |
| }; |
| }; |
| |
| thermal-zones { |
| soc { |
| polling-delay-passive = <250>; /* milliseconds */ |
| polling-delay = <1000>; /* milliseconds */ |
| thermal-sensors = <&thermal_sensor>; |
| |
| cooling-maps { |
| map0 { |
| trip = <&soc_passive>; |
| cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&mali THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; |
| }; |
| |
| map1 { |
| trip = <&soc_hot>; |
| cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| <&mali THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; |
| }; |
| }; |
| |
| trips { |
| soc_passive: soc-passive { |
| temperature = <80000>; /* millicelsius */ |
| hysteresis = <2000>; /* millicelsius */ |
| type = "passive"; |
| }; |
| |
| soc_hot: soc-hot { |
| temperature = <90000>; /* millicelsius */ |
| hysteresis = <2000>; /* millicelsius */ |
| type = "hot"; |
| }; |
| |
| soc_critical: soc-critical { |
| temperature = <110000>; /* millicelsius */ |
| hysteresis = <2000>; /* millicelsius */ |
| type = "critical"; |
| }; |
| }; |
| }; |
| }; |
| |
| mmcbus: bus@c8000000 { |
| compatible = "simple-bus"; |
| reg = <0xc8000000 0x8000>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges = <0x0 0xc8000000 0x8000>; |
| |
| ddr_clkc: clock-controller@400 { |
| compatible = "amlogic,meson8b-ddr-clkc"; |
| reg = <0x400 0x20>; |
| clocks = <&xtal>; |
| clock-names = "xtal"; |
| #clock-cells = <1>; |
| }; |
| |
| dmcbus: bus@6000 { |
| compatible = "simple-bus"; |
| reg = <0x6000 0x400>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges = <0x0 0x6000 0x400>; |
| |
| canvas: video-lut@48 { |
| compatible = "amlogic,meson8b-canvas", |
| "amlogic,canvas"; |
| reg = <0x48 0x14>; |
| }; |
| }; |
| }; |
| |
| apb: bus@d0000000 { |
| compatible = "simple-bus"; |
| reg = <0xd0000000 0x200000>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges = <0x0 0xd0000000 0x200000>; |
| |
| mali: gpu@c0000 { |
| compatible = "amlogic,meson8b-mali", "arm,mali-450"; |
| reg = <0xc0000 0x40000>; |
| interrupts = <GIC_SPI 160 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 161 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 162 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 163 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 164 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 165 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 166 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 167 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "gp", "gpmmu", "pp", "pmu", |
| "pp0", "ppmmu0", "pp1", "ppmmu1"; |
| resets = <&reset RESET_MALI>; |
| clocks = <&clkc CLKID_CLK81>, <&clkc CLKID_MALI>; |
| clock-names = "bus", "core"; |
| operating-points-v2 = <&gpu_opp_table>; |
| #cooling-cells = <2>; /* min followed by max */ |
| }; |
| }; |
| }; /* end of / */ |
| |
| &aiu { |
| compatible = "amlogic,aiu-meson8b", "amlogic,aiu"; |
| clocks = <&clkc CLKID_AIU_GLUE>, |
| <&clkc CLKID_I2S_OUT>, |
| <&clkc CLKID_AOCLK_GATE>, |
| <&clkc CLKID_CTS_AMCLK>, |
| <&clkc CLKID_MIXER_IFACE>, |
| <&clkc CLKID_IEC958>, |
| <&clkc CLKID_IEC958_GATE>, |
| <&clkc CLKID_CTS_MCLK_I958>, |
| <&clkc CLKID_CTS_I958>; |
| clock-names = "pclk", |
| "i2s_pclk", |
| "i2s_aoclk", |
| "i2s_mclk", |
| "i2s_mixer", |
| "spdif_pclk", |
| "spdif_aoclk", |
| "spdif_mclk", |
| "spdif_mclk_sel"; |
| resets = <&reset RESET_AIU>; |
| }; |
| |
| &aobus { |
| pmu: pmu@e0 { |
| compatible = "amlogic,meson8b-pmu", "syscon"; |
| reg = <0xe0 0x18>; |
| }; |
| |
| pinctrl_aobus: pinctrl@84 { |
| compatible = "amlogic,meson8b-aobus-pinctrl"; |
| reg = <0x84 0xc>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges; |
| |
| gpio_ao: ao-bank@14 { |
| reg = <0x14 0x4>, |
| <0x2c 0x4>, |
| <0x24 0x8>; |
| reg-names = "mux", "pull", "gpio"; |
| gpio-controller; |
| #gpio-cells = <2>; |
| gpio-ranges = <&pinctrl_aobus 0 0 16>; |
| }; |
| |
| i2s_am_clk_pins: i2s-am-clk-out { |
| mux { |
| groups = "i2s_am_clk_out"; |
| function = "i2s"; |
| bias-disable; |
| }; |
| }; |
| |
| i2s_out_ao_clk_pins: i2s-ao-clk-out { |
| mux { |
| groups = "i2s_ao_clk_out"; |
| function = "i2s"; |
| bias-disable; |
| }; |
| }; |
| |
| i2s_out_lr_clk_pins: i2s-lr-clk-out { |
| mux { |
| groups = "i2s_lr_clk_out"; |
| function = "i2s"; |
| bias-disable; |
| }; |
| }; |
| |
| i2s_out_ch01_ao_pins: i2s-out-ch01 { |
| mux { |
| groups = "i2s_out_01"; |
| function = "i2s"; |
| bias-disable; |
| }; |
| }; |
| |
| spdif_out_1_pins: spdif-out-1 { |
| mux { |
| groups = "spdif_out_1"; |
| function = "spdif_1"; |
| bias-disable; |
| }; |
| }; |
| |
| uart_ao_a_pins: uart_ao_a { |
| mux { |
| groups = "uart_tx_ao_a", "uart_rx_ao_a"; |
| function = "uart_ao"; |
| bias-disable; |
| }; |
| }; |
| |
| ir_recv_pins: remote { |
| mux { |
| groups = "remote_input"; |
| function = "remote"; |
| bias-disable; |
| }; |
| }; |
| }; |
| }; |
| |
| &ao_arc_rproc { |
| compatible= "amlogic,meson8b-ao-arc", "amlogic,meson-mx-ao-arc"; |
| amlogic,secbus2 = <&secbus2>; |
| sram = <&ao_arc_sram>; |
| resets = <&reset RESET_MEDIA_CPU>; |
| clocks = <&clkc CLKID_AO_MEDIA_CPU>; |
| }; |
| |
| &cbus { |
| reset: reset-controller@4404 { |
| compatible = "amlogic,meson8b-reset"; |
| reg = <0x4404 0x9c>; |
| #reset-cells = <1>; |
| }; |
| |
| analog_top: analog-top@81a8 { |
| compatible = "amlogic,meson8b-analog-top", "syscon"; |
| reg = <0x81a8 0x14>; |
| }; |
| |
| pwm_ef: pwm@86c0 { |
| compatible = "amlogic,meson8b-pwm"; |
| reg = <0x86c0 0x10>; |
| #pwm-cells = <3>; |
| status = "disabled"; |
| }; |
| |
| clock-measure@8758 { |
| compatible = "amlogic,meson8b-clk-measure"; |
| reg = <0x8758 0x1c>; |
| }; |
| |
| pinctrl_cbus: pinctrl@9880 { |
| compatible = "amlogic,meson8b-cbus-pinctrl"; |
| reg = <0x9880 0x10>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges; |
| |
| gpio: banks@80b0 { |
| reg = <0x80b0 0x28>, |
| <0x80e8 0x18>, |
| <0x8120 0x18>, |
| <0x8030 0x38>; |
| reg-names = "mux", "pull", "pull-enable", "gpio"; |
| gpio-controller; |
| #gpio-cells = <2>; |
| gpio-ranges = <&pinctrl_cbus 0 0 83>; |
| }; |
| |
| eth_rgmii_pins: eth-rgmii { |
| mux { |
| groups = "eth_tx_clk", |
| "eth_tx_en", |
| "eth_txd1_0", |
| "eth_txd0_0", |
| "eth_rx_clk", |
| "eth_rx_dv", |
| "eth_rxd1", |
| "eth_rxd0", |
| "eth_mdio_en", |
| "eth_mdc", |
| "eth_ref_clk", |
| "eth_txd2", |
| "eth_txd3", |
| "eth_rxd3", |
| "eth_rxd2"; |
| function = "ethernet"; |
| bias-disable; |
| }; |
| }; |
| |
| eth_rmii_pins: eth-rmii { |
| mux { |
| groups = "eth_tx_en", |
| "eth_txd1_0", |
| "eth_txd0_0", |
| "eth_rx_clk", |
| "eth_rx_dv", |
| "eth_rxd1", |
| "eth_rxd0", |
| "eth_mdio_en", |
| "eth_mdc"; |
| function = "ethernet"; |
| bias-disable; |
| }; |
| }; |
| |
| i2c_a_pins: i2c-a { |
| mux { |
| groups = "i2c_sda_a", "i2c_sck_a"; |
| function = "i2c_a"; |
| bias-disable; |
| }; |
| }; |
| |
| sd_b_pins: sd-b { |
| mux { |
| groups = "sd_d0_b", "sd_d1_b", "sd_d2_b", |
| "sd_d3_b", "sd_clk_b", "sd_cmd_b"; |
| function = "sd_b"; |
| bias-disable; |
| }; |
| }; |
| |
| sdxc_c_pins: sdxc-c { |
| mux { |
| groups = "sdxc_d0_c", "sdxc_d13_c", |
| "sdxc_d47_c", "sdxc_clk_c", |
| "sdxc_cmd_c"; |
| function = "sdxc_c"; |
| bias-pull-up; |
| }; |
| }; |
| |
| pwm_c1_pins: pwm-c1 { |
| mux { |
| groups = "pwm_c1"; |
| function = "pwm_c"; |
| bias-disable; |
| }; |
| }; |
| |
| pwm_d_pins: pwm-d { |
| mux { |
| groups = "pwm_d"; |
| function = "pwm_d"; |
| bias-disable; |
| }; |
| }; |
| |
| uart_b0_pins: uart-b0 { |
| mux { |
| groups = "uart_tx_b0", |
| "uart_rx_b0"; |
| function = "uart_b"; |
| bias-disable; |
| }; |
| }; |
| |
| uart_b0_cts_rts_pins: uart-b0-cts-rts { |
| mux { |
| groups = "uart_cts_b0", |
| "uart_rts_b0"; |
| function = "uart_b"; |
| bias-disable; |
| }; |
| }; |
| }; |
| }; |
| |
| &ahb_sram { |
| ao_arc_sram: ao-arc-sram@0 { |
| compatible = "amlogic,meson8b-ao-arc-sram"; |
| reg = <0x0 0x8000>; |
| pool; |
| }; |
| |
| smp-sram@1ff80 { |
| compatible = "amlogic,meson8b-smp-sram"; |
| reg = <0x1ff80 0x8>; |
| }; |
| }; |
| |
| |
| &efuse { |
| compatible = "amlogic,meson8b-efuse"; |
| clocks = <&clkc CLKID_EFUSE>; |
| clock-names = "core"; |
| |
| temperature_calib: calib@1f4 { |
| /* only the upper two bytes are relevant */ |
| reg = <0x1f4 0x4>; |
| }; |
| }; |
| |
| ðmac { |
| compatible = "amlogic,meson8b-dwmac", "snps,dwmac-3.70a", "snps,dwmac"; |
| |
| reg = <0xc9410000 0x10000 |
| 0xc1108140 0x4>; |
| |
| clocks = <&clkc CLKID_ETH>, |
| <&clkc CLKID_MPLL2>, |
| <&clkc CLKID_MPLL2>, |
| <&clkc CLKID_FCLK_DIV2>; |
| clock-names = "stmmaceth", "clkin0", "clkin1", "timing-adjustment"; |
| rx-fifo-depth = <4096>; |
| tx-fifo-depth = <2048>; |
| |
| resets = <&reset RESET_ETHERNET>; |
| reset-names = "stmmaceth"; |
| |
| power-domains = <&pwrc PWRC_MESON8_ETHERNET_MEM_ID>; |
| }; |
| |
| &gpio_intc { |
| compatible = "amlogic,meson-gpio-intc", |
| "amlogic,meson8b-gpio-intc"; |
| status = "okay"; |
| }; |
| |
| &hhi { |
| clkc: clock-controller { |
| compatible = "amlogic,meson8b-clkc"; |
| clocks = <&xtal>, <&ddr_clkc DDR_CLKID_DDR_PLL>; |
| clock-names = "xtal", "ddr_pll"; |
| #clock-cells = <1>; |
| #reset-cells = <1>; |
| }; |
| |
| pwrc: power-controller { |
| compatible = "amlogic,meson8b-pwrc"; |
| #power-domain-cells = <1>; |
| amlogic,ao-sysctrl = <&pmu>; |
| resets = <&reset RESET_DBLK>, |
| <&reset RESET_PIC_DC>, |
| <&reset RESET_HDMI_APB>, |
| <&reset RESET_HDMI_SYSTEM_RESET>, |
| <&reset RESET_VENCI>, |
| <&reset RESET_VENCP>, |
| <&reset RESET_VDAC_4>, |
| <&reset RESET_VENCL>, |
| <&reset RESET_VIU>, |
| <&reset RESET_VENC>, |
| <&reset RESET_RDMA>; |
| reset-names = "dblk", "pic_dc", "hdmi_apb", "hdmi_system", |
| "venci", "vencp", "vdac", "vencl", "viu", |
| "venc", "rdma"; |
| clocks = <&clkc CLKID_VPU>; |
| clock-names = "vpu"; |
| assigned-clocks = <&clkc CLKID_VPU>; |
| assigned-clock-rates = <182142857>; |
| }; |
| }; |
| |
| &hwrng { |
| compatible = "amlogic,meson8b-rng", "amlogic,meson-rng"; |
| clocks = <&clkc CLKID_RNG0>; |
| clock-names = "core"; |
| }; |
| |
| &i2c_AO { |
| clocks = <&clkc CLKID_CLK81>; |
| }; |
| |
| &i2c_A { |
| clocks = <&clkc CLKID_I2C>; |
| }; |
| |
| &i2c_B { |
| clocks = <&clkc CLKID_I2C>; |
| }; |
| |
| &L2 { |
| arm,data-latency = <3 3 3>; |
| arm,tag-latency = <2 2 2>; |
| arm,filter-ranges = <0x100000 0xc0000000>; |
| prefetch-data = <1>; |
| prefetch-instr = <1>; |
| arm,shared-override; |
| }; |
| |
| &periph { |
| scu@0 { |
| compatible = "arm,cortex-a5-scu"; |
| reg = <0x0 0x100>; |
| }; |
| |
| timer@200 { |
| compatible = "arm,cortex-a5-global-timer"; |
| reg = <0x200 0x20>; |
| interrupts = <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_EDGE_RISING)>; |
| clocks = <&clkc CLKID_PERIPH>; |
| |
| /* |
| * the arm_global_timer driver currently does not handle clock |
| * rate changes. Keep it disabled for now. |
| */ |
| status = "disabled"; |
| }; |
| |
| timer@600 { |
| compatible = "arm,cortex-a5-twd-timer"; |
| reg = <0x600 0x20>; |
| interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_EDGE_RISING)>; |
| clocks = <&clkc CLKID_PERIPH>; |
| }; |
| }; |
| |
| &pwm_ab { |
| compatible = "amlogic,meson8b-pwm"; |
| }; |
| |
| &pwm_cd { |
| compatible = "amlogic,meson8b-pwm"; |
| }; |
| |
| &rtc { |
| compatible = "amlogic,meson8b-rtc"; |
| resets = <&reset RESET_RTC>; |
| }; |
| |
| &saradc { |
| compatible = "amlogic,meson8b-saradc", "amlogic,meson-saradc"; |
| clocks = <&xtal>, <&clkc CLKID_SAR_ADC>; |
| clock-names = "clkin", "core"; |
| amlogic,hhi-sysctrl = <&hhi>; |
| nvmem-cells = <&temperature_calib>; |
| nvmem-cell-names = "temperature_calib"; |
| }; |
| |
| &sdhc { |
| compatible = "amlogic,meson8-sdhc", "amlogic,meson-mx-sdhc"; |
| clocks = <&xtal>, |
| <&clkc CLKID_FCLK_DIV4>, |
| <&clkc CLKID_FCLK_DIV3>, |
| <&clkc CLKID_FCLK_DIV5>, |
| <&clkc CLKID_SDHC>; |
| clock-names = "clkin0", "clkin1", "clkin2", "clkin3", "pclk"; |
| }; |
| |
| &secbus { |
| secbus2: system-controller@4000 { |
| compatible = "amlogic,meson8b-secbus2", "syscon"; |
| reg = <0x4000 0x2000>; |
| }; |
| }; |
| |
| &sdio { |
| compatible = "amlogic,meson8b-sdio", "amlogic,meson-mx-sdio"; |
| clocks = <&clkc CLKID_SDIO>, <&clkc CLKID_CLK81>; |
| clock-names = "core", "clkin"; |
| }; |
| |
| &timer_abcde { |
| clocks = <&xtal>, <&clkc CLKID_CLK81>; |
| clock-names = "xtal", "pclk"; |
| }; |
| |
| &uart_AO { |
| compatible = "amlogic,meson8b-uart", "amlogic,meson-ao-uart"; |
| clocks = <&xtal>, <&clkc CLKID_CLK81>, <&clkc CLKID_CLK81>; |
| clock-names = "xtal", "pclk", "baud"; |
| }; |
| |
| &uart_A { |
| compatible = "amlogic,meson8b-uart"; |
| clocks = <&xtal>, <&clkc CLKID_UART0>, <&clkc CLKID_CLK81>; |
| clock-names = "xtal", "pclk", "baud"; |
| }; |
| |
| &uart_B { |
| compatible = "amlogic,meson8b-uart"; |
| clocks = <&xtal>, <&clkc CLKID_UART0>, <&clkc CLKID_CLK81>; |
| clock-names = "xtal", "pclk", "baud"; |
| }; |
| |
| &uart_C { |
| compatible = "amlogic,meson8b-uart"; |
| clocks = <&xtal>, <&clkc CLKID_UART0>, <&clkc CLKID_CLK81>; |
| clock-names = "xtal", "pclk", "baud"; |
| }; |
| |
| &usb0 { |
| compatible = "amlogic,meson8b-usb", "snps,dwc2"; |
| clocks = <&clkc CLKID_USB0_DDR_BRIDGE>; |
| clock-names = "otg"; |
| }; |
| |
| &usb1 { |
| compatible = "amlogic,meson8b-usb", "snps,dwc2"; |
| clocks = <&clkc CLKID_USB1_DDR_BRIDGE>; |
| clock-names = "otg"; |
| }; |
| |
| &usb0_phy { |
| compatible = "amlogic,meson8b-usb2-phy", "amlogic,meson-mx-usb2-phy"; |
| clocks = <&clkc CLKID_USB>, <&clkc CLKID_USB0>; |
| clock-names = "usb_general", "usb"; |
| resets = <&reset RESET_USB_OTG>; |
| }; |
| |
| &usb1_phy { |
| compatible = "amlogic,meson8b-usb2-phy", "amlogic,meson-mx-usb2-phy"; |
| clocks = <&clkc CLKID_USB>, <&clkc CLKID_USB1>; |
| clock-names = "usb_general", "usb"; |
| resets = <&reset RESET_USB_OTG>; |
| }; |
| |
| &wdt { |
| compatible = "amlogic,meson8b-wdt"; |
| }; |