| // SPDX-License-Identifier: GPL-2.0 |
| /dts-v1/; |
| |
| #include <dt-bindings/interrupt-controller/arm-gic.h> |
| #include <dt-bindings/mfd/qcom-rpm.h> |
| #include <dt-bindings/clock/qcom,rpmcc.h> |
| #include <dt-bindings/clock/qcom,gcc-ipq806x.h> |
| #include <dt-bindings/clock/qcom,lcc-ipq806x.h> |
| #include <dt-bindings/gpio/gpio.h> |
| #include <dt-bindings/reset/qcom,gcc-ipq806x.h> |
| #include <dt-bindings/soc/qcom,gsbi.h> |
| #include <dt-bindings/interrupt-controller/arm-gic.h> |
| |
| / { |
| #address-cells = <1>; |
| #size-cells = <1>; |
| model = "Qualcomm IPQ8064"; |
| compatible = "qcom,ipq8064"; |
| interrupt-parent = <&intc>; |
| |
| cpus { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| cpu0: cpu@0 { |
| compatible = "qcom,krait"; |
| enable-method = "qcom,kpss-acc-v1"; |
| device_type = "cpu"; |
| reg = <0>; |
| next-level-cache = <&L2>; |
| qcom,acc = <&acc0>; |
| qcom,saw = <&saw0>; |
| }; |
| |
| cpu1: cpu@1 { |
| compatible = "qcom,krait"; |
| enable-method = "qcom,kpss-acc-v1"; |
| device_type = "cpu"; |
| reg = <1>; |
| next-level-cache = <&L2>; |
| qcom,acc = <&acc1>; |
| qcom,saw = <&saw1>; |
| }; |
| |
| L2: l2-cache { |
| compatible = "cache"; |
| cache-level = <2>; |
| }; |
| }; |
| |
| thermal-zones { |
| sensor0-thermal { |
| polling-delay-passive = <0>; |
| polling-delay = <0>; |
| thermal-sensors = <&tsens 0>; |
| |
| trips { |
| cpu-critical { |
| temperature = <105000>; |
| hysteresis = <2000>; |
| type = "critical"; |
| }; |
| |
| cpu-hot { |
| temperature = <95000>; |
| hysteresis = <2000>; |
| type = "hot"; |
| }; |
| }; |
| }; |
| |
| sensor1-thermal { |
| polling-delay-passive = <0>; |
| polling-delay = <0>; |
| thermal-sensors = <&tsens 1>; |
| |
| trips { |
| cpu-critical { |
| temperature = <105000>; |
| hysteresis = <2000>; |
| type = "critical"; |
| }; |
| |
| cpu-hot { |
| temperature = <95000>; |
| hysteresis = <2000>; |
| type = "hot"; |
| }; |
| }; |
| }; |
| |
| sensor2-thermal { |
| polling-delay-passive = <0>; |
| polling-delay = <0>; |
| thermal-sensors = <&tsens 2>; |
| |
| trips { |
| cpu-critical { |
| temperature = <105000>; |
| hysteresis = <2000>; |
| type = "critical"; |
| }; |
| |
| cpu-hot { |
| temperature = <95000>; |
| hysteresis = <2000>; |
| type = "hot"; |
| }; |
| }; |
| }; |
| |
| sensor3-thermal { |
| polling-delay-passive = <0>; |
| polling-delay = <0>; |
| thermal-sensors = <&tsens 3>; |
| |
| trips { |
| cpu-critical { |
| temperature = <105000>; |
| hysteresis = <2000>; |
| type = "critical"; |
| }; |
| |
| cpu-hot { |
| temperature = <95000>; |
| hysteresis = <2000>; |
| type = "hot"; |
| }; |
| }; |
| }; |
| |
| sensor4-thermal { |
| polling-delay-passive = <0>; |
| polling-delay = <0>; |
| thermal-sensors = <&tsens 4>; |
| |
| trips { |
| cpu-critical { |
| temperature = <105000>; |
| hysteresis = <2000>; |
| type = "critical"; |
| }; |
| |
| cpu-hot { |
| temperature = <95000>; |
| hysteresis = <2000>; |
| type = "hot"; |
| }; |
| }; |
| }; |
| |
| sensor5-thermal { |
| polling-delay-passive = <0>; |
| polling-delay = <0>; |
| thermal-sensors = <&tsens 5>; |
| |
| trips { |
| cpu-critical { |
| temperature = <105000>; |
| hysteresis = <2000>; |
| type = "critical"; |
| }; |
| |
| cpu-hot { |
| temperature = <95000>; |
| hysteresis = <2000>; |
| type = "hot"; |
| }; |
| }; |
| }; |
| |
| sensor6-thermal { |
| polling-delay-passive = <0>; |
| polling-delay = <0>; |
| thermal-sensors = <&tsens 6>; |
| |
| trips { |
| cpu-critical { |
| temperature = <105000>; |
| hysteresis = <2000>; |
| type = "critical"; |
| }; |
| |
| cpu-hot { |
| temperature = <95000>; |
| hysteresis = <2000>; |
| type = "hot"; |
| }; |
| }; |
| }; |
| |
| sensor7-thermal { |
| polling-delay-passive = <0>; |
| polling-delay = <0>; |
| thermal-sensors = <&tsens 7>; |
| |
| trips { |
| cpu-critical { |
| temperature = <105000>; |
| hysteresis = <2000>; |
| type = "critical"; |
| }; |
| |
| cpu-hot { |
| temperature = <95000>; |
| hysteresis = <2000>; |
| type = "hot"; |
| }; |
| }; |
| }; |
| |
| sensor8-thermal { |
| polling-delay-passive = <0>; |
| polling-delay = <0>; |
| thermal-sensors = <&tsens 8>; |
| |
| trips { |
| cpu-critical { |
| temperature = <105000>; |
| hysteresis = <2000>; |
| type = "critical"; |
| }; |
| |
| cpu-hot { |
| temperature = <95000>; |
| hysteresis = <2000>; |
| type = "hot"; |
| }; |
| }; |
| }; |
| |
| sensor9-thermal { |
| polling-delay-passive = <0>; |
| polling-delay = <0>; |
| thermal-sensors = <&tsens 9>; |
| |
| trips { |
| cpu-critical { |
| temperature = <105000>; |
| hysteresis = <2000>; |
| type = "critical"; |
| }; |
| |
| cpu-hot { |
| temperature = <95000>; |
| hysteresis = <2000>; |
| type = "hot"; |
| }; |
| }; |
| }; |
| |
| sensor10-thermal { |
| polling-delay-passive = <0>; |
| polling-delay = <0>; |
| thermal-sensors = <&tsens 10>; |
| |
| trips { |
| cpu-critical { |
| temperature = <105000>; |
| hysteresis = <2000>; |
| type = "critical"; |
| }; |
| |
| cpu-hot { |
| temperature = <95000>; |
| hysteresis = <2000>; |
| type = "hot"; |
| }; |
| }; |
| }; |
| }; |
| |
| memory { |
| device_type = "memory"; |
| reg = <0x0 0x0>; |
| }; |
| |
| cpu-pmu { |
| compatible = "qcom,krait-pmu"; |
| interrupts = <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(2) | |
| IRQ_TYPE_LEVEL_HIGH)>; |
| }; |
| |
| reserved-memory { |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges; |
| |
| nss@40000000 { |
| reg = <0x40000000 0x1000000>; |
| no-map; |
| }; |
| |
| smem: smem@41000000 { |
| reg = <0x41000000 0x200000>; |
| no-map; |
| }; |
| }; |
| |
| clocks { |
| cxo_board { |
| compatible = "fixed-clock"; |
| #clock-cells = <0>; |
| clock-frequency = <25000000>; |
| }; |
| |
| pxo_board { |
| compatible = "fixed-clock"; |
| #clock-cells = <0>; |
| clock-frequency = <25000000>; |
| }; |
| |
| sleep_clk: sleep_clk { |
| compatible = "fixed-clock"; |
| clock-frequency = <32768>; |
| #clock-cells = <0>; |
| }; |
| }; |
| |
| firmware { |
| scm { |
| compatible = "qcom,scm-ipq806x", "qcom,scm"; |
| }; |
| }; |
| |
| soc: soc { |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges; |
| compatible = "simple-bus"; |
| |
| lpass@28100000 { |
| compatible = "qcom,lpass-cpu"; |
| status = "disabled"; |
| clocks = <&lcc AHBIX_CLK>, |
| <&lcc MI2S_OSR_CLK>, |
| <&lcc MI2S_BIT_CLK>; |
| clock-names = "ahbix-clk", |
| "mi2s-osr-clk", |
| "mi2s-bit-clk"; |
| interrupts = <GIC_SPI 85 IRQ_TYPE_EDGE_RISING>; |
| interrupt-names = "lpass-irq-lpaif"; |
| reg = <0x28100000 0x10000>; |
| reg-names = "lpass-lpaif"; |
| }; |
| |
| qcom_pinmux: pinmux@800000 { |
| compatible = "qcom,ipq8064-pinctrl"; |
| reg = <0x800000 0x4000>; |
| |
| gpio-controller; |
| gpio-ranges = <&qcom_pinmux 0 0 69>; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>; |
| |
| pcie0_pins: pcie0_pinmux { |
| mux { |
| pins = "gpio3"; |
| function = "pcie1_rst"; |
| drive-strength = <12>; |
| bias-disable; |
| }; |
| }; |
| |
| pcie1_pins: pcie1_pinmux { |
| mux { |
| pins = "gpio48"; |
| function = "pcie2_rst"; |
| drive-strength = <12>; |
| bias-disable; |
| }; |
| }; |
| |
| pcie2_pins: pcie2_pinmux { |
| mux { |
| pins = "gpio63"; |
| function = "pcie3_rst"; |
| drive-strength = <12>; |
| bias-disable; |
| }; |
| }; |
| |
| spi_pins: spi_pins { |
| mux { |
| pins = "gpio18", "gpio19", "gpio21"; |
| function = "gsbi5"; |
| drive-strength = <10>; |
| bias-none; |
| }; |
| }; |
| |
| leds_pins: leds_pins { |
| mux { |
| pins = "gpio7", "gpio8", "gpio9", |
| "gpio26", "gpio53"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-pull-down; |
| output-low; |
| }; |
| }; |
| |
| buttons_pins: buttons_pins { |
| mux { |
| pins = "gpio54"; |
| drive-strength = <2>; |
| bias-pull-up; |
| }; |
| }; |
| |
| nand_pins: nand_pins { |
| mux { |
| pins = "gpio34", "gpio35", "gpio36", |
| "gpio37", "gpio38", "gpio39", |
| "gpio40", "gpio41", "gpio42", |
| "gpio43", "gpio44", "gpio45", |
| "gpio46", "gpio47"; |
| function = "nand"; |
| drive-strength = <10>; |
| bias-disable; |
| }; |
| |
| pullups { |
| pins = "gpio39"; |
| bias-pull-up; |
| }; |
| |
| hold { |
| pins = "gpio40", "gpio41", "gpio42", |
| "gpio43", "gpio44", "gpio45", |
| "gpio46", "gpio47"; |
| bias-bus-hold; |
| }; |
| }; |
| }; |
| |
| intc: interrupt-controller@2000000 { |
| compatible = "qcom,msm-qgic2"; |
| interrupt-controller; |
| #interrupt-cells = <3>; |
| reg = <0x02000000 0x1000>, |
| <0x02002000 0x1000>; |
| }; |
| |
| timer@200a000 { |
| compatible = "qcom,kpss-timer", |
| "qcom,kpss-wdt-ipq8064", "qcom,msm-timer"; |
| interrupts = <GIC_PPI 1 (GIC_CPU_MASK_SIMPLE(2) | |
| IRQ_TYPE_EDGE_RISING)>, |
| <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(2) | |
| IRQ_TYPE_EDGE_RISING)>, |
| <GIC_PPI 3 (GIC_CPU_MASK_SIMPLE(2) | |
| IRQ_TYPE_EDGE_RISING)>, |
| <GIC_PPI 4 (GIC_CPU_MASK_SIMPLE(2) | |
| IRQ_TYPE_EDGE_RISING)>, |
| <GIC_PPI 5 (GIC_CPU_MASK_SIMPLE(2) | |
| IRQ_TYPE_EDGE_RISING)>; |
| reg = <0x0200a000 0x100>; |
| clock-frequency = <25000000>, |
| <32768>; |
| clocks = <&sleep_clk>; |
| clock-names = "sleep"; |
| cpu-offset = <0x80000>; |
| }; |
| |
| acc0: clock-controller@2088000 { |
| compatible = "qcom,kpss-acc-v1"; |
| reg = <0x02088000 0x1000>, <0x02008000 0x1000>; |
| }; |
| |
| acc1: clock-controller@2098000 { |
| compatible = "qcom,kpss-acc-v1"; |
| reg = <0x02098000 0x1000>, <0x02008000 0x1000>; |
| }; |
| |
| adm_dma: dma-controller@18300000 { |
| compatible = "qcom,adm"; |
| reg = <0x18300000 0x100000>; |
| interrupts = <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>; |
| #dma-cells = <1>; |
| |
| clocks = <&gcc ADM0_CLK>, <&gcc ADM0_PBUS_CLK>; |
| clock-names = "core", "iface"; |
| |
| resets = <&gcc ADM0_RESET>, |
| <&gcc ADM0_PBUS_RESET>, |
| <&gcc ADM0_C0_RESET>, |
| <&gcc ADM0_C1_RESET>, |
| <&gcc ADM0_C2_RESET>; |
| reset-names = "clk", "pbus", "c0", "c1", "c2"; |
| qcom,ee = <0>; |
| |
| status = "disabled"; |
| }; |
| |
| saw0: regulator@2089000 { |
| compatible = "qcom,saw2"; |
| reg = <0x02089000 0x1000>, <0x02009000 0x1000>; |
| regulator; |
| }; |
| |
| saw1: regulator@2099000 { |
| compatible = "qcom,saw2"; |
| reg = <0x02099000 0x1000>, <0x02009000 0x1000>; |
| regulator; |
| }; |
| |
| gsbi2: gsbi@12480000 { |
| compatible = "qcom,gsbi-v1.0.0"; |
| cell-index = <2>; |
| reg = <0x12480000 0x100>; |
| clocks = <&gcc GSBI2_H_CLK>; |
| clock-names = "iface"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges; |
| status = "disabled"; |
| |
| syscon-tcsr = <&tcsr>; |
| |
| gsbi2_serial: serial@12490000 { |
| compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm"; |
| reg = <0x12490000 0x1000>, |
| <0x12480000 0x1000>; |
| interrupts = <GIC_SPI 195 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&gcc GSBI2_UART_CLK>, <&gcc GSBI2_H_CLK>; |
| clock-names = "core", "iface"; |
| status = "disabled"; |
| }; |
| |
| i2c@124a0000 { |
| compatible = "qcom,i2c-qup-v1.1.1"; |
| reg = <0x124a0000 0x1000>; |
| interrupts = <GIC_SPI 196 IRQ_TYPE_LEVEL_HIGH>; |
| |
| clocks = <&gcc GSBI2_QUP_CLK>, <&gcc GSBI2_H_CLK>; |
| clock-names = "core", "iface"; |
| status = "disabled"; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| }; |
| }; |
| |
| gsbi4: gsbi@16300000 { |
| compatible = "qcom,gsbi-v1.0.0"; |
| cell-index = <4>; |
| reg = <0x16300000 0x100>; |
| clocks = <&gcc GSBI4_H_CLK>; |
| clock-names = "iface"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges; |
| status = "disabled"; |
| |
| syscon-tcsr = <&tcsr>; |
| |
| gsbi4_serial: serial@16340000 { |
| compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm"; |
| reg = <0x16340000 0x1000>, |
| <0x16300000 0x1000>; |
| interrupts = <GIC_SPI 152 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&gcc GSBI4_UART_CLK>, <&gcc GSBI4_H_CLK>; |
| clock-names = "core", "iface"; |
| status = "disabled"; |
| }; |
| |
| i2c@16380000 { |
| compatible = "qcom,i2c-qup-v1.1.1"; |
| reg = <0x16380000 0x1000>; |
| interrupts = <GIC_SPI 153 IRQ_TYPE_LEVEL_HIGH>; |
| |
| clocks = <&gcc GSBI4_QUP_CLK>, <&gcc GSBI4_H_CLK>; |
| clock-names = "core", "iface"; |
| status = "disabled"; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| }; |
| }; |
| |
| gsbi5: gsbi@1a200000 { |
| compatible = "qcom,gsbi-v1.0.0"; |
| cell-index = <5>; |
| reg = <0x1a200000 0x100>; |
| clocks = <&gcc GSBI5_H_CLK>; |
| clock-names = "iface"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges; |
| status = "disabled"; |
| |
| syscon-tcsr = <&tcsr>; |
| |
| gsbi5_serial: serial@1a240000 { |
| compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm"; |
| reg = <0x1a240000 0x1000>, |
| <0x1a200000 0x1000>; |
| interrupts = <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&gcc GSBI5_UART_CLK>, <&gcc GSBI5_H_CLK>; |
| clock-names = "core", "iface"; |
| status = "disabled"; |
| }; |
| |
| i2c@1a280000 { |
| compatible = "qcom,i2c-qup-v1.1.1"; |
| reg = <0x1a280000 0x1000>; |
| interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>; |
| |
| clocks = <&gcc GSBI5_QUP_CLK>, <&gcc GSBI5_H_CLK>; |
| clock-names = "core", "iface"; |
| status = "disabled"; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| }; |
| |
| spi@1a280000 { |
| compatible = "qcom,spi-qup-v1.1.1"; |
| reg = <0x1a280000 0x1000>; |
| interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>; |
| |
| clocks = <&gcc GSBI5_QUP_CLK>, <&gcc GSBI5_H_CLK>; |
| clock-names = "core", "iface"; |
| status = "disabled"; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| }; |
| }; |
| |
| gsbi7: gsbi@16600000 { |
| status = "disabled"; |
| compatible = "qcom,gsbi-v1.0.0"; |
| cell-index = <7>; |
| reg = <0x16600000 0x100>; |
| clocks = <&gcc GSBI7_H_CLK>; |
| clock-names = "iface"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges; |
| syscon-tcsr = <&tcsr>; |
| |
| gsbi7_serial: serial@16640000 { |
| compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm"; |
| reg = <0x16640000 0x1000>, |
| <0x16600000 0x1000>; |
| interrupts = <GIC_SPI 158 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&gcc GSBI7_UART_CLK>, <&gcc GSBI7_H_CLK>; |
| clock-names = "core", "iface"; |
| status = "disabled"; |
| }; |
| }; |
| |
| rng@1a500000 { |
| compatible = "qcom,prng"; |
| reg = <0x1a500000 0x200>; |
| clocks = <&gcc PRNG_CLK>; |
| clock-names = "core"; |
| }; |
| |
| sata_phy: sata-phy@1b400000 { |
| compatible = "qcom,ipq806x-sata-phy"; |
| reg = <0x1b400000 0x200>; |
| |
| clocks = <&gcc SATA_PHY_CFG_CLK>; |
| clock-names = "cfg"; |
| |
| #phy-cells = <0>; |
| status = "disabled"; |
| }; |
| |
| nand: nand-controller@1ac00000 { |
| compatible = "qcom,ipq806x-nand"; |
| reg = <0x1ac00000 0x800>; |
| |
| pinctrl-0 = <&nand_pins>; |
| pinctrl-names = "default"; |
| |
| clocks = <&gcc EBI2_CLK>, |
| <&gcc EBI2_AON_CLK>; |
| clock-names = "core", "aon"; |
| |
| dmas = <&adm_dma 3>; |
| dma-names = "rxtx"; |
| qcom,cmd-crci = <15>; |
| qcom,data-crci = <3>; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| status = "disabled"; |
| }; |
| |
| sata: sata@29000000 { |
| compatible = "qcom,ipq806x-ahci", "generic-ahci"; |
| reg = <0x29000000 0x180>; |
| |
| interrupts = <GIC_SPI 209 IRQ_TYPE_LEVEL_HIGH>; |
| |
| clocks = <&gcc SFAB_SATA_S_H_CLK>, |
| <&gcc SATA_H_CLK>, |
| <&gcc SATA_A_CLK>, |
| <&gcc SATA_RXOOB_CLK>, |
| <&gcc SATA_PMALIVE_CLK>; |
| clock-names = "slave_face", "iface", "core", |
| "rxoob", "pmalive"; |
| |
| assigned-clocks = <&gcc SATA_RXOOB_CLK>, <&gcc SATA_PMALIVE_CLK>; |
| assigned-clock-rates = <100000000>, <100000000>; |
| |
| phys = <&sata_phy>; |
| phy-names = "sata-phy"; |
| status = "disabled"; |
| }; |
| |
| qcom,ssbi@500000 { |
| compatible = "qcom,ssbi"; |
| reg = <0x00500000 0x1000>; |
| qcom,controller-type = "pmic-arbiter"; |
| }; |
| |
| qfprom: qfprom@700000 { |
| compatible = "qcom,qfprom"; |
| reg = <0x00700000 0x1000>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| tsens_calib: calib@400 { |
| reg = <0x400 0xb>; |
| }; |
| tsens_calib_backup: calib_backup@410 { |
| reg = <0x410 0xb>; |
| }; |
| }; |
| |
| gcc: clock-controller@900000 { |
| compatible = "qcom,gcc-ipq8064"; |
| reg = <0x00900000 0x4000>; |
| #clock-cells = <1>; |
| #reset-cells = <1>; |
| #power-domain-cells = <1>; |
| |
| tsens: thermal-sensor@900000 { |
| compatible = "qcom,ipq8064-tsens"; |
| |
| nvmem-cells = <&tsens_calib>, <&tsens_calib_backup>; |
| nvmem-cell-names = "calib", "calib_backup"; |
| interrupts = <GIC_SPI 178 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "uplow"; |
| |
| #qcom,sensors = <11>; |
| #thermal-sensor-cells = <1>; |
| }; |
| }; |
| |
| rpm: rpm@108000 { |
| compatible = "qcom,rpm-ipq8064"; |
| reg = <0x108000 0x1000>; |
| qcom,ipc = <&l2cc 0x8 2>; |
| |
| interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "ack", "err", "wakeup"; |
| |
| clocks = <&gcc RPM_MSG_RAM_H_CLK>; |
| clock-names = "ram"; |
| |
| rpmcc: clock-controller { |
| compatible = "qcom,rpmcc-ipq806x", "qcom,rpmcc"; |
| #clock-cells = <1>; |
| }; |
| }; |
| |
| tcsr: syscon@1a400000 { |
| compatible = "qcom,tcsr-ipq8064", "syscon"; |
| reg = <0x1a400000 0x100>; |
| }; |
| |
| l2cc: clock-controller@2011000 { |
| compatible = "qcom,kpss-gcc", "syscon"; |
| reg = <0x2011000 0x1000>; |
| clocks = <&gcc PLL8_VOTE>, <&gcc PXO_SRC>; |
| clock-names = "pll8_vote", "pxo"; |
| clock-output-names = "acpu_l2_aux"; |
| }; |
| |
| lcc: clock-controller@28000000 { |
| compatible = "qcom,lcc-ipq8064"; |
| reg = <0x28000000 0x1000>; |
| #clock-cells = <1>; |
| #reset-cells = <1>; |
| }; |
| |
| pcie0: pci@1b500000 { |
| compatible = "qcom,pcie-ipq8064"; |
| reg = <0x1b500000 0x1000 |
| 0x1b502000 0x80 |
| 0x1b600000 0x100 |
| 0x0ff00000 0x100000>; |
| reg-names = "dbi", "elbi", "parf", "config"; |
| device_type = "pci"; |
| linux,pci-domain = <0>; |
| bus-range = <0x00 0xff>; |
| num-lanes = <1>; |
| #address-cells = <3>; |
| #size-cells = <2>; |
| |
| ranges = <0x81000000 0 0x0fe00000 0x0fe00000 0 0x00100000 /* downstream I/O */ |
| 0x82000000 0 0x08000000 0x08000000 0 0x07e00000>; /* non-prefetchable memory */ |
| |
| interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "msi"; |
| #interrupt-cells = <1>; |
| interrupt-map-mask = <0 0 0 0x7>; |
| interrupt-map = <0 0 0 1 &intc 0 36 IRQ_TYPE_LEVEL_HIGH>, /* int_a */ |
| <0 0 0 2 &intc 0 37 IRQ_TYPE_LEVEL_HIGH>, /* int_b */ |
| <0 0 0 3 &intc 0 38 IRQ_TYPE_LEVEL_HIGH>, /* int_c */ |
| <0 0 0 4 &intc 0 39 IRQ_TYPE_LEVEL_HIGH>; /* int_d */ |
| |
| clocks = <&gcc PCIE_A_CLK>, |
| <&gcc PCIE_H_CLK>, |
| <&gcc PCIE_PHY_CLK>, |
| <&gcc PCIE_AUX_CLK>, |
| <&gcc PCIE_ALT_REF_CLK>; |
| clock-names = "core", "iface", "phy", "aux", "ref"; |
| |
| assigned-clocks = <&gcc PCIE_ALT_REF_CLK>; |
| assigned-clock-rates = <100000000>; |
| |
| resets = <&gcc PCIE_ACLK_RESET>, |
| <&gcc PCIE_HCLK_RESET>, |
| <&gcc PCIE_POR_RESET>, |
| <&gcc PCIE_PCI_RESET>, |
| <&gcc PCIE_PHY_RESET>, |
| <&gcc PCIE_EXT_RESET>; |
| reset-names = "axi", "ahb", "por", "pci", "phy", "ext"; |
| |
| pinctrl-0 = <&pcie0_pins>; |
| pinctrl-names = "default"; |
| |
| status = "disabled"; |
| perst-gpio = <&qcom_pinmux 3 GPIO_ACTIVE_LOW>; |
| }; |
| |
| pcie1: pci@1b700000 { |
| compatible = "qcom,pcie-ipq8064"; |
| reg = <0x1b700000 0x1000 |
| 0x1b702000 0x80 |
| 0x1b800000 0x100 |
| 0x31f00000 0x100000>; |
| reg-names = "dbi", "elbi", "parf", "config"; |
| device_type = "pci"; |
| linux,pci-domain = <1>; |
| bus-range = <0x00 0xff>; |
| num-lanes = <1>; |
| #address-cells = <3>; |
| #size-cells = <2>; |
| |
| ranges = <0x81000000 0 0x31e00000 0x31e00000 0 0x00100000 /* downstream I/O */ |
| 0x82000000 0 0x2e000000 0x2e000000 0 0x03e00000>; /* non-prefetchable memory */ |
| |
| interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "msi"; |
| #interrupt-cells = <1>; |
| interrupt-map-mask = <0 0 0 0x7>; |
| interrupt-map = <0 0 0 1 &intc 0 58 IRQ_TYPE_LEVEL_HIGH>, /* int_a */ |
| <0 0 0 2 &intc 0 59 IRQ_TYPE_LEVEL_HIGH>, /* int_b */ |
| <0 0 0 3 &intc 0 60 IRQ_TYPE_LEVEL_HIGH>, /* int_c */ |
| <0 0 0 4 &intc 0 61 IRQ_TYPE_LEVEL_HIGH>; /* int_d */ |
| |
| clocks = <&gcc PCIE_1_A_CLK>, |
| <&gcc PCIE_1_H_CLK>, |
| <&gcc PCIE_1_PHY_CLK>, |
| <&gcc PCIE_1_AUX_CLK>, |
| <&gcc PCIE_1_ALT_REF_CLK>; |
| clock-names = "core", "iface", "phy", "aux", "ref"; |
| |
| assigned-clocks = <&gcc PCIE_1_ALT_REF_CLK>; |
| assigned-clock-rates = <100000000>; |
| |
| resets = <&gcc PCIE_1_ACLK_RESET>, |
| <&gcc PCIE_1_HCLK_RESET>, |
| <&gcc PCIE_1_POR_RESET>, |
| <&gcc PCIE_1_PCI_RESET>, |
| <&gcc PCIE_1_PHY_RESET>, |
| <&gcc PCIE_1_EXT_RESET>; |
| reset-names = "axi", "ahb", "por", "pci", "phy", "ext"; |
| |
| pinctrl-0 = <&pcie1_pins>; |
| pinctrl-names = "default"; |
| |
| status = "disabled"; |
| perst-gpio = <&qcom_pinmux 48 GPIO_ACTIVE_LOW>; |
| }; |
| |
| pcie2: pci@1b900000 { |
| compatible = "qcom,pcie-ipq8064"; |
| reg = <0x1b900000 0x1000 |
| 0x1b902000 0x80 |
| 0x1ba00000 0x100 |
| 0x35f00000 0x100000>; |
| reg-names = "dbi", "elbi", "parf", "config"; |
| device_type = "pci"; |
| linux,pci-domain = <2>; |
| bus-range = <0x00 0xff>; |
| num-lanes = <1>; |
| #address-cells = <3>; |
| #size-cells = <2>; |
| |
| ranges = <0x81000000 0 0x35e00000 0x35e00000 0 0x00100000 /* downstream I/O */ |
| 0x82000000 0 0x32000000 0x32000000 0 0x03e00000>; /* non-prefetchable memory */ |
| |
| interrupts = <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "msi"; |
| #interrupt-cells = <1>; |
| interrupt-map-mask = <0 0 0 0x7>; |
| interrupt-map = <0 0 0 1 &intc 0 72 IRQ_TYPE_LEVEL_HIGH>, /* int_a */ |
| <0 0 0 2 &intc 0 73 IRQ_TYPE_LEVEL_HIGH>, /* int_b */ |
| <0 0 0 3 &intc 0 74 IRQ_TYPE_LEVEL_HIGH>, /* int_c */ |
| <0 0 0 4 &intc 0 75 IRQ_TYPE_LEVEL_HIGH>; /* int_d */ |
| |
| clocks = <&gcc PCIE_2_A_CLK>, |
| <&gcc PCIE_2_H_CLK>, |
| <&gcc PCIE_2_PHY_CLK>, |
| <&gcc PCIE_2_AUX_CLK>, |
| <&gcc PCIE_2_ALT_REF_CLK>; |
| clock-names = "core", "iface", "phy", "aux", "ref"; |
| |
| assigned-clocks = <&gcc PCIE_2_ALT_REF_CLK>; |
| assigned-clock-rates = <100000000>; |
| |
| resets = <&gcc PCIE_2_ACLK_RESET>, |
| <&gcc PCIE_2_HCLK_RESET>, |
| <&gcc PCIE_2_POR_RESET>, |
| <&gcc PCIE_2_PCI_RESET>, |
| <&gcc PCIE_2_PHY_RESET>, |
| <&gcc PCIE_2_EXT_RESET>; |
| reset-names = "axi", "ahb", "por", "pci", "phy", "ext"; |
| |
| pinctrl-0 = <&pcie2_pins>; |
| pinctrl-names = "default"; |
| |
| status = "disabled"; |
| perst-gpio = <&qcom_pinmux 63 GPIO_ACTIVE_LOW>; |
| }; |
| |
| nss_common: syscon@03000000 { |
| compatible = "syscon"; |
| reg = <0x03000000 0x0000FFFF>; |
| }; |
| |
| qsgmii_csr: syscon@1bb00000 { |
| compatible = "syscon"; |
| reg = <0x1bb00000 0x000001FF>; |
| }; |
| |
| stmmac_axi_setup: stmmac-axi-config { |
| snps,wr_osr_lmt = <7>; |
| snps,rd_osr_lmt = <7>; |
| snps,blen = <16 0 0 0 0 0 0>; |
| }; |
| |
| gmac0: ethernet@37000000 { |
| device_type = "network"; |
| compatible = "qcom,ipq806x-gmac"; |
| reg = <0x37000000 0x200000>; |
| interrupts = <GIC_SPI 220 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "macirq"; |
| |
| snps,axi-config = <&stmmac_axi_setup>; |
| snps,pbl = <32>; |
| snps,aal = <1>; |
| |
| qcom,nss-common = <&nss_common>; |
| qcom,qsgmii-csr = <&qsgmii_csr>; |
| |
| clocks = <&gcc GMAC_CORE1_CLK>; |
| clock-names = "stmmaceth"; |
| |
| resets = <&gcc GMAC_CORE1_RESET>, |
| <&gcc GMAC_AHB_RESET>; |
| reset-names = "stmmaceth", "ahb"; |
| |
| status = "disabled"; |
| }; |
| |
| gmac1: ethernet@37200000 { |
| device_type = "network"; |
| compatible = "qcom,ipq806x-gmac"; |
| reg = <0x37200000 0x200000>; |
| interrupts = <GIC_SPI 223 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "macirq"; |
| |
| snps,axi-config = <&stmmac_axi_setup>; |
| snps,pbl = <32>; |
| snps,aal = <1>; |
| |
| qcom,nss-common = <&nss_common>; |
| qcom,qsgmii-csr = <&qsgmii_csr>; |
| |
| clocks = <&gcc GMAC_CORE2_CLK>; |
| clock-names = "stmmaceth"; |
| |
| resets = <&gcc GMAC_CORE2_RESET>, |
| <&gcc GMAC_AHB_RESET>; |
| reset-names = "stmmaceth", "ahb"; |
| |
| status = "disabled"; |
| }; |
| |
| gmac2: ethernet@37400000 { |
| device_type = "network"; |
| compatible = "qcom,ipq806x-gmac"; |
| reg = <0x37400000 0x200000>; |
| interrupts = <GIC_SPI 226 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "macirq"; |
| |
| snps,axi-config = <&stmmac_axi_setup>; |
| snps,pbl = <32>; |
| snps,aal = <1>; |
| |
| qcom,nss-common = <&nss_common>; |
| qcom,qsgmii-csr = <&qsgmii_csr>; |
| |
| clocks = <&gcc GMAC_CORE3_CLK>; |
| clock-names = "stmmaceth"; |
| |
| resets = <&gcc GMAC_CORE3_RESET>, |
| <&gcc GMAC_AHB_RESET>; |
| reset-names = "stmmaceth", "ahb"; |
| |
| status = "disabled"; |
| }; |
| |
| gmac3: ethernet@37600000 { |
| device_type = "network"; |
| compatible = "qcom,ipq806x-gmac"; |
| reg = <0x37600000 0x200000>; |
| interrupts = <GIC_SPI 229 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "macirq"; |
| |
| snps,axi-config = <&stmmac_axi_setup>; |
| snps,pbl = <32>; |
| snps,aal = <1>; |
| |
| qcom,nss-common = <&nss_common>; |
| qcom,qsgmii-csr = <&qsgmii_csr>; |
| |
| clocks = <&gcc GMAC_CORE4_CLK>; |
| clock-names = "stmmaceth"; |
| |
| resets = <&gcc GMAC_CORE4_RESET>, |
| <&gcc GMAC_AHB_RESET>; |
| reset-names = "stmmaceth", "ahb"; |
| |
| status = "disabled"; |
| }; |
| |
| hs_phy_0: phy@100f8800 { |
| compatible = "qcom,ipq806x-usb-phy-hs"; |
| reg = <0x100f8800 0x30>; |
| clocks = <&gcc USB30_0_UTMI_CLK>; |
| clock-names = "ref"; |
| #phy-cells = <0>; |
| |
| status = "disabled"; |
| }; |
| |
| ss_phy_0: phy@100f8830 { |
| compatible = "qcom,ipq806x-usb-phy-ss"; |
| reg = <0x100f8830 0x30>; |
| clocks = <&gcc USB30_0_MASTER_CLK>; |
| clock-names = "ref"; |
| #phy-cells = <0>; |
| |
| status = "disabled"; |
| }; |
| |
| usb3_0: usb3@100f8800 { |
| compatible = "qcom,ipq8064-dwc3", "qcom,dwc3"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| reg = <0x100f8800 0x8000>; |
| clocks = <&gcc USB30_0_MASTER_CLK>; |
| clock-names = "core"; |
| |
| ranges; |
| |
| resets = <&gcc USB30_0_MASTER_RESET>; |
| reset-names = "master"; |
| |
| status = "disabled"; |
| |
| dwc3_0: dwc3@10000000 { |
| compatible = "snps,dwc3"; |
| reg = <0x10000000 0xcd00>; |
| interrupts = <GIC_SPI 205 IRQ_TYPE_LEVEL_HIGH>; |
| phys = <&hs_phy_0>, <&ss_phy_0>; |
| phy-names = "usb2-phy", "usb3-phy"; |
| dr_mode = "host"; |
| snps,dis_u3_susphy_quirk; |
| }; |
| }; |
| |
| hs_phy_1: phy@110f8800 { |
| compatible = "qcom,ipq806x-usb-phy-hs"; |
| reg = <0x110f8800 0x30>; |
| clocks = <&gcc USB30_1_UTMI_CLK>; |
| clock-names = "ref"; |
| #phy-cells = <0>; |
| }; |
| |
| ss_phy_1: phy@110f8830 { |
| compatible = "qcom,ipq806x-usb-phy-ss"; |
| reg = <0x110f8830 0x30>; |
| clocks = <&gcc USB30_1_MASTER_CLK>; |
| clock-names = "ref"; |
| #phy-cells = <0>; |
| }; |
| |
| usb3_1: usb3@110f8800 { |
| compatible = "qcom,ipq8064-dwc3", "qcom,dwc3"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| reg = <0x110f8800 0x8000>; |
| clocks = <&gcc USB30_1_MASTER_CLK>; |
| clock-names = "core"; |
| |
| ranges; |
| |
| resets = <&gcc USB30_1_MASTER_RESET>; |
| reset-names = "master"; |
| |
| status = "disabled"; |
| |
| dwc3_1: dwc3@11000000 { |
| compatible = "snps,dwc3"; |
| reg = <0x11000000 0xcd00>; |
| interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>; |
| phys = <&hs_phy_1>, <&ss_phy_1>; |
| phy-names = "usb2-phy", "usb3-phy"; |
| dr_mode = "host"; |
| snps,dis_u3_susphy_quirk; |
| }; |
| }; |
| |
| vsdcc_fixed: vsdcc-regulator { |
| compatible = "regulator-fixed"; |
| regulator-name = "SDCC Power"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| regulator-always-on; |
| }; |
| |
| sdcc1bam: dma@12402000 { |
| compatible = "qcom,bam-v1.3.0"; |
| reg = <0x12402000 0x8000>; |
| interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&gcc SDC1_H_CLK>; |
| clock-names = "bam_clk"; |
| #dma-cells = <1>; |
| qcom,ee = <0>; |
| }; |
| |
| sdcc3bam: dma@12182000 { |
| compatible = "qcom,bam-v1.3.0"; |
| reg = <0x12182000 0x8000>; |
| interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&gcc SDC3_H_CLK>; |
| clock-names = "bam_clk"; |
| #dma-cells = <1>; |
| qcom,ee = <0>; |
| }; |
| |
| amba: amba { |
| compatible = "simple-bus"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges; |
| |
| sdcc1: mmc@12400000 { |
| status = "disabled"; |
| compatible = "arm,pl18x", "arm,primecell"; |
| arm,primecell-periphid = <0x00051180>; |
| reg = <0x12400000 0x2000>; |
| interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "cmd_irq"; |
| clocks = <&gcc SDC1_CLK>, <&gcc SDC1_H_CLK>; |
| clock-names = "mclk", "apb_pclk"; |
| bus-width = <8>; |
| max-frequency = <96000000>; |
| non-removable; |
| cap-sd-highspeed; |
| cap-mmc-highspeed; |
| mmc-ddr-1_8v; |
| vmmc-supply = <&vsdcc_fixed>; |
| dmas = <&sdcc1bam 2>, <&sdcc1bam 1>; |
| dma-names = "tx", "rx"; |
| }; |
| |
| sdcc3: mmc@12180000 { |
| compatible = "arm,pl18x", "arm,primecell"; |
| arm,primecell-periphid = <0x00051180>; |
| status = "disabled"; |
| reg = <0x12180000 0x2000>; |
| interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "cmd_irq"; |
| clocks = <&gcc SDC3_CLK>, <&gcc SDC3_H_CLK>; |
| clock-names = "mclk", "apb_pclk"; |
| bus-width = <8>; |
| cap-sd-highspeed; |
| cap-mmc-highspeed; |
| max-frequency = <192000000>; |
| sd-uhs-sdr104; |
| sd-uhs-ddr50; |
| vqmmc-supply = <&vsdcc_fixed>; |
| dmas = <&sdcc3bam 2>, <&sdcc3bam 1>; |
| dma-names = "tx", "rx"; |
| }; |
| }; |
| }; |
| }; |