| Stefan Roese | 6a22845 | 2012-03-13 04:56:37 +0000 | [diff] [blame] | 1 | * STMicroelectronics 10/100/1000 Ethernet driver (GMAC) |
| 2 | |
| 3 | Required properties: |
| Dinh Nguyen | 84c9f8c4 | 2012-07-18 13:28:26 +0000 | [diff] [blame] | 4 | - compatible: Should be "snps,dwmac-<ip_version>" "snps,dwmac" |
| 5 | For backwards compatibility: "st,spear600-gmac" is also supported. |
| Stefan Roese | 6a22845 | 2012-03-13 04:56:37 +0000 | [diff] [blame] | 6 | - reg: Address and length of the register set for the device |
| 7 | - interrupt-parent: Should be the phandle for the interrupt controller |
| 8 | that services interrupts for this device |
| 9 | - interrupts: Should contain the STMMAC interrupts |
| 10 | - interrupt-names: Should contain the interrupt names "macirq" |
| 11 | "eth_wake_irq" if this interrupt is supported in the "interrupts" |
| 12 | property |
| 13 | - phy-mode: String, operation mode of the PHY interface. |
| 14 | Supported values are: "mii", "rmii", "gmii", "rgmii". |
| Srinivas Kandagatla | 25c83b5 | 2013-07-04 10:35:41 +0100 | [diff] [blame] | 15 | - snps,phy-addr phy address to connect to. |
| Srinivas Kandagatla | 0e07647 | 2013-07-04 10:35:48 +0100 | [diff] [blame] | 16 | - snps,reset-gpio gpio number for phy reset. |
| 17 | - snps,reset-active-low boolean flag to indicate if phy reset is active low. |
| 18 | - snps,reset-delays-us is triplet of delays |
| 19 | The 1st cell is reset pre-delay in micro seconds. |
| 20 | The 2nd cell is reset pulse in micro seconds. |
| 21 | The 3rd cell is reset post-delay in micro seconds. |
| Srinivas Kandagatla | 25c83b5 | 2013-07-04 10:35:41 +0100 | [diff] [blame] | 22 | - snps,pbl Programmable Burst Length |
| 23 | - snps,fixed-burst Program the DMA to use the fixed burst mode |
| 24 | - snps,mixed-burst Program the DMA to use the mixed burst mode |
| Sonic Zhang | e2a240c | 2013-08-28 18:55:39 +0800 | [diff] [blame] | 25 | - snps,force_thresh_dma_mode Force DMA to use the threshold mode for |
| 26 | both tx and rx |
| 27 | - snps,force_sf_dma_mode Force DMA to use the Store and Forward |
| 28 | mode for both tx and rx. This flag is |
| 29 | ignored if force_thresh_dma_mode is set. |
| Stefan Roese | 6a22845 | 2012-03-13 04:56:37 +0000 | [diff] [blame] | 30 | |
| 31 | Optional properties: |
| 32 | - mac-address: 6 bytes, mac address |
| Chen-Yu Tsai | c5e4ddb | 2014-01-17 21:24:41 +0800 | [diff] [blame^] | 33 | - resets: Should contain a phandle to the STMMAC reset signal, if any |
| 34 | - reset-names: Should contain the reset signal name "stmmaceth", if a |
| 35 | reset phandle is given |
| Stefan Roese | 6a22845 | 2012-03-13 04:56:37 +0000 | [diff] [blame] | 36 | |
| 37 | Examples: |
| 38 | |
| 39 | gmac0: ethernet@e0800000 { |
| 40 | compatible = "st,spear600-gmac"; |
| 41 | reg = <0xe0800000 0x8000>; |
| 42 | interrupt-parent = <&vic1>; |
| 43 | interrupts = <24 23>; |
| 44 | interrupt-names = "macirq", "eth_wake_irq"; |
| 45 | mac-address = [000000000000]; /* Filled in by U-Boot */ |
| 46 | phy-mode = "gmii"; |
| 47 | }; |