drivers/regulator/scmi-regulator.c - SHIFTPHONES/kernel/common - Gitiles

 // SPDX-License-Identifier: GPL-2.0
 //
 // System Control and Management Interface (SCMI) based regulator driver
 //
 // Copyright (C) 2020 ARM Ltd.
 //
 // Implements a regulator driver on top of the SCMI Voltage Protocol.
 //
 // The ARM SCMI Protocol aims in general to hide as much as possible all the
 // underlying operational details while providing an abstracted interface for
 // its users to operate upon: as a consequence the resulting operational
 // capabilities and configurability of this regulator device are much more
 // limited than the ones usually available on a standard physical regulator.
 //
 // The supported SCMI regulator ops are restricted to the bare minimum:
 //
 //  - 'status_ops': enable/disable/is_enabled
 //  - 'voltage_ops': get_voltage_sel/set_voltage_sel
 //		     list_voltage/map_voltage
 //
 // Each SCMI regulator instance is associated, through the means of a proper DT
 // entry description, to a specific SCMI Voltage Domain.

 #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt

 #include <linux/linear_range.h>
 #include <linux/module.h>
 #include <linux/of.h>
 #include <linux/regulator/driver.h>
 #include <linux/regulator/machine.h>
 #include <linux/regulator/of_regulator.h>
 #include <linux/scmi_protocol.h>
 #include <linux/slab.h>
 #include <linux/types.h>

 struct scmi_regulator {
 	u32 id;
 	struct scmi_device *sdev;
 	struct regulator_dev *rdev;
 	struct device_node *of_node;
 	struct regulator_desc desc;
 	struct regulator_config conf;
 };

 struct scmi_regulator_info {
 	int num_doms;
 	struct scmi_regulator **sregv;
 };

 static int scmi_reg_enable(struct regulator_dev *rdev)
 {
 	struct scmi_regulator *sreg = rdev_get_drvdata(rdev);
 	const struct scmi_handle *handle = sreg->sdev->handle;

 	return handle->voltage_ops->config_set(handle, sreg->id,
 					       SCMI_VOLTAGE_ARCH_STATE_ON);
 }

 static int scmi_reg_disable(struct regulator_dev *rdev)
 {
 	struct scmi_regulator *sreg = rdev_get_drvdata(rdev);
 	const struct scmi_handle *handle = sreg->sdev->handle;

 	return handle->voltage_ops->config_set(handle, sreg->id,
 					       SCMI_VOLTAGE_ARCH_STATE_OFF);
 }

 static int scmi_reg_is_enabled(struct regulator_dev *rdev)
 {
 	int ret;
 	u32 config;
 	struct scmi_regulator *sreg = rdev_get_drvdata(rdev);
 	const struct scmi_handle *handle = sreg->sdev->handle;

 	ret = handle->voltage_ops->config_get(handle, sreg->id,
 					      &config);
 	if (ret) {
 		dev_err(&sreg->sdev->dev,
 			"Error %d reading regulator %s status.\n",
 			ret, sreg->desc.name);
 		return ret;
 	}

 	return config & SCMI_VOLTAGE_ARCH_STATE_ON;
 }

 static int scmi_reg_get_voltage_sel(struct regulator_dev *rdev)
 {
 	int ret;
 	s32 volt_uV;
 	struct scmi_regulator *sreg = rdev_get_drvdata(rdev);
 	const struct scmi_handle *handle = sreg->sdev->handle;

 	ret = handle->voltage_ops->level_get(handle, sreg->id, &volt_uV);
 	if (ret)
 		return ret;

 	return sreg->desc.ops->map_voltage(rdev, volt_uV, volt_uV);
 }

 static int scmi_reg_set_voltage_sel(struct regulator_dev *rdev,
 				    unsigned int selector)
 {
 	s32 volt_uV;
 	struct scmi_regulator *sreg = rdev_get_drvdata(rdev);
 	const struct scmi_handle *handle = sreg->sdev->handle;

 	volt_uV = sreg->desc.ops->list_voltage(rdev, selector);
 	if (volt_uV <= 0)
 		return -EINVAL;

 	return handle->voltage_ops->level_set(handle, sreg->id, 0x0, volt_uV);
 }

 static const struct regulator_ops scmi_reg_fixed_ops = {
 	.enable = scmi_reg_enable,
 	.disable = scmi_reg_disable,
 	.is_enabled = scmi_reg_is_enabled,
 };

 static const struct regulator_ops scmi_reg_linear_ops = {
 	.enable = scmi_reg_enable,
 	.disable = scmi_reg_disable,
 	.is_enabled = scmi_reg_is_enabled,
 	.get_voltage_sel = scmi_reg_get_voltage_sel,
 	.set_voltage_sel = scmi_reg_set_voltage_sel,
 	.list_voltage = regulator_list_voltage_linear,
 	.map_voltage = regulator_map_voltage_linear,
 };

 static const struct regulator_ops scmi_reg_discrete_ops = {
 	.enable = scmi_reg_enable,
 	.disable = scmi_reg_disable,
 	.is_enabled = scmi_reg_is_enabled,
 	.get_voltage_sel = scmi_reg_get_voltage_sel,
 	.set_voltage_sel = scmi_reg_set_voltage_sel,
 	.list_voltage = regulator_list_voltage_table,
 	.map_voltage = regulator_map_voltage_iterate,
 };

 static int
 scmi_config_linear_regulator_mappings(struct scmi_regulator *sreg,
 				      const struct scmi_voltage_info *vinfo)
 {
 	s32 delta_uV;

 	/*
 	 * Note that SCMI voltage domains describable by linear ranges
 	 * (segments) {low, high, step} are guaranteed to come in one single
 	 * triplet by the SCMI Voltage Domain protocol support itself.
 	 */

 	delta_uV = (vinfo->levels_uv[SCMI_VOLTAGE_SEGMENT_HIGH] -
 			vinfo->levels_uv[SCMI_VOLTAGE_SEGMENT_LOW]);

 	/* Rule out buggy negative-intervals answers from fw */
 	if (delta_uV < 0) {
 		dev_err(&sreg->sdev->dev,
 			"Invalid volt-range %d-%duV for domain %d\n",
 			vinfo->levels_uv[SCMI_VOLTAGE_SEGMENT_LOW],
 			vinfo->levels_uv[SCMI_VOLTAGE_SEGMENT_HIGH],
 			sreg->id);
 		return -EINVAL;
 	}

 	if (!delta_uV) {
 		/* Just one fixed voltage exposed by SCMI */
 		sreg->desc.fixed_uV =
 			vinfo->levels_uv[SCMI_VOLTAGE_SEGMENT_LOW];
 		sreg->desc.n_voltages = 1;
 		sreg->desc.ops = &scmi_reg_fixed_ops;
 	} else {
 		/* One simple linear mapping. */
 		sreg->desc.min_uV =
 			vinfo->levels_uv[SCMI_VOLTAGE_SEGMENT_LOW];
 		sreg->desc.uV_step =
 			vinfo->levels_uv[SCMI_VOLTAGE_SEGMENT_STEP];
 		sreg->desc.linear_min_sel = 0;
 		sreg->desc.n_voltages = delta_uV / sreg->desc.uV_step;
 		sreg->desc.ops = &scmi_reg_linear_ops;
 	}

 	return 0;
 }

 static int
 scmi_config_discrete_regulator_mappings(struct scmi_regulator *sreg,
 					const struct scmi_voltage_info *vinfo)
 {
 	/* Discrete non linear levels are mapped to volt_table */
 	sreg->desc.n_voltages = vinfo->num_levels;

 	if (sreg->desc.n_voltages > 1) {
 		sreg->desc.volt_table = (const unsigned int *)vinfo->levels_uv;
 		sreg->desc.ops = &scmi_reg_discrete_ops;
 	} else {
 		sreg->desc.fixed_uV = vinfo->levels_uv[0];
 		sreg->desc.ops = &scmi_reg_fixed_ops;
 	}

 	return 0;
 }

 static int scmi_regulator_common_init(struct scmi_regulator *sreg)
 {
 	int ret;
 	const struct scmi_handle *handle = sreg->sdev->handle;
 	struct device *dev = &sreg->sdev->dev;
 	const struct scmi_voltage_info *vinfo;

 	vinfo = handle->voltage_ops->info_get(handle, sreg->id);
 	if (!vinfo) {
 		dev_warn(dev, "Failure to get voltage domain %d\n",
 			 sreg->id);
 		return -ENODEV;
 	}

 	/*
 	 * Regulator framework does not fully support negative voltages
 	 * so we discard any voltage domain reported as supporting negative
 	 * voltages: as a consequence each levels_uv entry is guaranteed to
 	 * be non-negative from here on.
 	 */
 	if (vinfo->negative_volts_allowed) {
 		dev_warn(dev, "Negative voltages NOT supported...skip %s\n",
 			 sreg->of_node->full_name);
 		return -EOPNOTSUPP;
 	}

 	sreg->desc.name = devm_kasprintf(dev, GFP_KERNEL, "%s", vinfo->name);
 	if (!sreg->desc.name)
 		return -ENOMEM;

 	sreg->desc.id = sreg->id;
 	sreg->desc.type = REGULATOR_VOLTAGE;
 	sreg->desc.owner = THIS_MODULE;
 	sreg->desc.of_match_full_name = true;
 	sreg->desc.of_match = sreg->of_node->full_name;
 	sreg->desc.regulators_node = "regulators";
 	if (vinfo->segmented)
 		ret = scmi_config_linear_regulator_mappings(sreg, vinfo);
 	else
 		ret = scmi_config_discrete_regulator_mappings(sreg, vinfo);
 	if (ret)
 		return ret;

 	/*
 	 * Using the scmi device here to have DT searched from Voltage
 	 * protocol node down.
 	 */
 	sreg->conf.dev = dev;

 	/* Store for later retrieval via rdev_get_drvdata() */
 	sreg->conf.driver_data = sreg;

 	return 0;
 }

 static int process_scmi_regulator_of_node(struct scmi_device *sdev,
 					  struct device_node *np,
 					  struct scmi_regulator_info *rinfo)
 {
 	u32 dom, ret;

 	ret = of_property_read_u32(np, "reg", &dom);
 	if (ret)
 		return ret;

 	if (dom >= rinfo->num_doms)
 		return -ENODEV;

 	if (rinfo->sregv[dom]) {
 		dev_err(&sdev->dev,
 			"SCMI Voltage Domain %d already in use. Skipping: %s\n",
 			dom, np->full_name);
 		return -EINVAL;
 	}

 	rinfo->sregv[dom] = devm_kzalloc(&sdev->dev,
 					 sizeof(struct scmi_regulator),
 					 GFP_KERNEL);
 	if (!rinfo->sregv[dom])
 		return -ENOMEM;

 	rinfo->sregv[dom]->id = dom;
 	rinfo->sregv[dom]->sdev = sdev;

 	/* get hold of good nodes */
 	of_node_get(np);
 	rinfo->sregv[dom]->of_node = np;

 	dev_dbg(&sdev->dev,
 		"Found SCMI Regulator entry -- OF node [%d] -> %s\n",
 		dom, np->full_name);

 	return 0;
 }

 static int scmi_regulator_probe(struct scmi_device *sdev)
 {
 	int d, ret, num_doms;
 	struct device_node *np, *child;
 	const struct scmi_handle *handle = sdev->handle;
 	struct scmi_regulator_info *rinfo;

 	if (!handle || !handle->voltage_ops)
 		return -ENODEV;

 	num_doms = handle->voltage_ops->num_domains_get(handle);
 	if (num_doms <= 0) {
 		if (!num_doms) {
 			dev_err(&sdev->dev,
 				"number of voltage domains invalid\n");
 			num_doms = -EINVAL;
 		} else {
 			dev_err(&sdev->dev,
 				"failed to get voltage domains - err:%d\n",
 				num_doms);
 		}

 		return num_doms;
 	}

 	rinfo = devm_kzalloc(&sdev->dev, sizeof(*rinfo), GFP_KERNEL);
 	if (!rinfo)
 		return -ENOMEM;

 	/* Allocate pointers array for all possible domains */
 	rinfo->sregv = devm_kcalloc(&sdev->dev, num_doms,
 				    sizeof(void *), GFP_KERNEL);
 	if (!rinfo->sregv)
 		return -ENOMEM;

 	rinfo->num_doms = num_doms;

 	/*
 	 * Start collecting into rinfo->sregv possibly good SCMI Regulators as
 	 * described by a well-formed DT entry and associated with an existing
 	 * plausible SCMI Voltage Domain number, all belonging to this SCMI
 	 * platform instance node (handle->dev->of_node).
 	 */
 	np = of_find_node_by_name(handle->dev->of_node, "regulators");
 	for_each_child_of_node(np, child) {
 		ret = process_scmi_regulator_of_node(sdev, child, rinfo);
 		/* abort on any mem issue */
 		if (ret == -ENOMEM)
 			return ret;
 	}

 	/*
 	 * Register a regulator for each valid regulator-DT-entry that we
 	 * can successfully reach via SCMI and has a valid associated voltage
 	 * domain.
 	 */
 	for (d = 0; d < num_doms; d++) {
 		struct scmi_regulator *sreg = rinfo->sregv[d];

 		/* Skip empty slots */
 		if (!sreg)
 			continue;

 		ret = scmi_regulator_common_init(sreg);
 		/* Skip invalid voltage domains */
 		if (ret)
 			continue;

 		sreg->rdev = devm_regulator_register(&sdev->dev, &sreg->desc,
 						     &sreg->conf);
 		if (IS_ERR(sreg->rdev)) {
 			sreg->rdev = NULL;
 			continue;
 		}

 		dev_info(&sdev->dev,
 			 "Regulator %s registered for domain [%d]\n",
 			 sreg->desc.name, sreg->id);
 	}

 	dev_set_drvdata(&sdev->dev, rinfo);

 	return 0;
 }

 static void scmi_regulator_remove(struct scmi_device *sdev)
 {
 	int d;
 	struct scmi_regulator_info *rinfo;

 	rinfo = dev_get_drvdata(&sdev->dev);
 	if (!rinfo)
 		return;

 	for (d = 0; d < rinfo->num_doms; d++) {
 		if (!rinfo->sregv[d])
 			continue;
 		of_node_put(rinfo->sregv[d]->of_node);
 	}
 }

 static const struct scmi_device_id scmi_regulator_id_table[] = {
 	{ SCMI_PROTOCOL_VOLTAGE,  "regulator" },
 	{ },
 };
 MODULE_DEVICE_TABLE(scmi, scmi_regulator_id_table);

 static struct scmi_driver scmi_drv = {
 	.name		= "scmi-regulator",
 	.probe		= scmi_regulator_probe,
 	.remove		= scmi_regulator_remove,
 	.id_table	= scmi_regulator_id_table,
 };

 module_scmi_driver(scmi_drv);

 MODULE_AUTHOR("Cristian Marussi <cristian.marussi@arm.com>");
 MODULE_DESCRIPTION("ARM SCMI regulator driver");
 MODULE_LICENSE("GPL v2");
	// SPDX-License-Identifier: GPL-2.0
	//
	// System Control and Management Interface (SCMI) based regulator driver
	//
	// Copyright (C) 2020 ARM Ltd.
	//
	// Implements a regulator driver on top of the SCMI Voltage Protocol.
	//
	// The ARM SCMI Protocol aims in general to hide as much as possible all the
	// underlying operational details while providing an abstracted interface for
	// its users to operate upon: as a consequence the resulting operational
	// capabilities and configurability of this regulator device are much more
	// limited than the ones usually available on a standard physical regulator.
	//
	// The supported SCMI regulator ops are restricted to the bare minimum:
	//
	// - 'status_ops': enable/disable/is_enabled
	// - 'voltage_ops': get_voltage_sel/set_voltage_sel
	// list_voltage/map_voltage
	//
	// Each SCMI regulator instance is associated, through the means of a proper DT
	// entry description, to a specific SCMI Voltage Domain.

	#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt

	#include <linux/linear_range.h>
	#include <linux/module.h>
	#include <linux/of.h>
	#include <linux/regulator/driver.h>
	#include <linux/regulator/machine.h>
	#include <linux/regulator/of_regulator.h>
	#include <linux/scmi_protocol.h>
	#include <linux/slab.h>
	#include <linux/types.h>

	struct scmi_regulator {
	u32 id;
	struct scmi_device *sdev;
	struct regulator_dev *rdev;
	struct device_node *of_node;
	struct regulator_desc desc;
	struct regulator_config conf;
	};

	struct scmi_regulator_info {
	int num_doms;
	struct scmi_regulator **sregv;
	};

	static int scmi_reg_enable(struct regulator_dev *rdev)
	{
	struct scmi_regulator *sreg = rdev_get_drvdata(rdev);
	const struct scmi_handle *handle = sreg->sdev->handle;

	return handle->voltage_ops->config_set(handle, sreg->id,
	SCMI_VOLTAGE_ARCH_STATE_ON);
	}

	static int scmi_reg_disable(struct regulator_dev *rdev)
	{
	struct scmi_regulator *sreg = rdev_get_drvdata(rdev);
	const struct scmi_handle *handle = sreg->sdev->handle;

	return handle->voltage_ops->config_set(handle, sreg->id,
	SCMI_VOLTAGE_ARCH_STATE_OFF);
	}

	static int scmi_reg_is_enabled(struct regulator_dev *rdev)
	{
	int ret;
	u32 config;
	struct scmi_regulator *sreg = rdev_get_drvdata(rdev);
	const struct scmi_handle *handle = sreg->sdev->handle;

	ret = handle->voltage_ops->config_get(handle, sreg->id,
	&config);
	if (ret) {
	dev_err(&sreg->sdev->dev,
	"Error %d reading regulator %s status.\n",
	ret, sreg->desc.name);
	return ret;
	}

	return config & SCMI_VOLTAGE_ARCH_STATE_ON;
	}

	static int scmi_reg_get_voltage_sel(struct regulator_dev *rdev)
	{
	int ret;
	s32 volt_uV;
	struct scmi_regulator *sreg = rdev_get_drvdata(rdev);
	const struct scmi_handle *handle = sreg->sdev->handle;

	ret = handle->voltage_ops->level_get(handle, sreg->id, &volt_uV);
	if (ret)
	return ret;

	return sreg->desc.ops->map_voltage(rdev, volt_uV, volt_uV);
	}

	static int scmi_reg_set_voltage_sel(struct regulator_dev *rdev,
	unsigned int selector)
	{
	s32 volt_uV;
	struct scmi_regulator *sreg = rdev_get_drvdata(rdev);
	const struct scmi_handle *handle = sreg->sdev->handle;

	volt_uV = sreg->desc.ops->list_voltage(rdev, selector);
	if (volt_uV <= 0)
	return -EINVAL;

	return handle->voltage_ops->level_set(handle, sreg->id, 0x0, volt_uV);
	}

	static const struct regulator_ops scmi_reg_fixed_ops = {
	.enable = scmi_reg_enable,
	.disable = scmi_reg_disable,
	.is_enabled = scmi_reg_is_enabled,
	};

	static const struct regulator_ops scmi_reg_linear_ops = {
	.enable = scmi_reg_enable,
	.disable = scmi_reg_disable,
	.is_enabled = scmi_reg_is_enabled,
	.get_voltage_sel = scmi_reg_get_voltage_sel,
	.set_voltage_sel = scmi_reg_set_voltage_sel,
	.list_voltage = regulator_list_voltage_linear,
	.map_voltage = regulator_map_voltage_linear,
	};

	static const struct regulator_ops scmi_reg_discrete_ops = {
	.enable = scmi_reg_enable,
	.disable = scmi_reg_disable,
	.is_enabled = scmi_reg_is_enabled,
	.get_voltage_sel = scmi_reg_get_voltage_sel,
	.set_voltage_sel = scmi_reg_set_voltage_sel,
	.list_voltage = regulator_list_voltage_table,
	.map_voltage = regulator_map_voltage_iterate,
	};

	static int
	scmi_config_linear_regulator_mappings(struct scmi_regulator *sreg,
	const struct scmi_voltage_info *vinfo)
	{
	s32 delta_uV;

	/*
	* Note that SCMI voltage domains describable by linear ranges
	* (segments) {low, high, step} are guaranteed to come in one single
	* triplet by the SCMI Voltage Domain protocol support itself.
	*/

	delta_uV = (vinfo->levels_uv[SCMI_VOLTAGE_SEGMENT_HIGH] -
	vinfo->levels_uv[SCMI_VOLTAGE_SEGMENT_LOW]);

	/* Rule out buggy negative-intervals answers from fw */
	if (delta_uV < 0) {
	dev_err(&sreg->sdev->dev,
	"Invalid volt-range %d-%duV for domain %d\n",
	vinfo->levels_uv[SCMI_VOLTAGE_SEGMENT_LOW],
	vinfo->levels_uv[SCMI_VOLTAGE_SEGMENT_HIGH],
	sreg->id);
	return -EINVAL;
	}

	if (!delta_uV) {
	/* Just one fixed voltage exposed by SCMI */
	sreg->desc.fixed_uV =
	vinfo->levels_uv[SCMI_VOLTAGE_SEGMENT_LOW];
	sreg->desc.n_voltages = 1;
	sreg->desc.ops = &scmi_reg_fixed_ops;
	} else {
	/* One simple linear mapping. */
	sreg->desc.min_uV =
	vinfo->levels_uv[SCMI_VOLTAGE_SEGMENT_LOW];
	sreg->desc.uV_step =
	vinfo->levels_uv[SCMI_VOLTAGE_SEGMENT_STEP];
	sreg->desc.linear_min_sel = 0;
	sreg->desc.n_voltages = delta_uV / sreg->desc.uV_step;
	sreg->desc.ops = &scmi_reg_linear_ops;
	}

	return 0;
	}

	static int
	scmi_config_discrete_regulator_mappings(struct scmi_regulator *sreg,
	const struct scmi_voltage_info *vinfo)
	{
	/* Discrete non linear levels are mapped to volt_table */
	sreg->desc.n_voltages = vinfo->num_levels;

	if (sreg->desc.n_voltages > 1) {
	sreg->desc.volt_table = (const unsigned int *)vinfo->levels_uv;
	sreg->desc.ops = &scmi_reg_discrete_ops;
	} else {
	sreg->desc.fixed_uV = vinfo->levels_uv[0];
	sreg->desc.ops = &scmi_reg_fixed_ops;
	}

	return 0;
	}

	static int scmi_regulator_common_init(struct scmi_regulator *sreg)
	{
	int ret;
	const struct scmi_handle *handle = sreg->sdev->handle;
	struct device *dev = &sreg->sdev->dev;
	const struct scmi_voltage_info *vinfo;

	vinfo = handle->voltage_ops->info_get(handle, sreg->id);
	if (!vinfo) {
	dev_warn(dev, "Failure to get voltage domain %d\n",
	sreg->id);
	return -ENODEV;
	}

	/*
	* Regulator framework does not fully support negative voltages
	* so we discard any voltage domain reported as supporting negative
	* voltages: as a consequence each levels_uv entry is guaranteed to
	* be non-negative from here on.
	*/
	if (vinfo->negative_volts_allowed) {
	dev_warn(dev, "Negative voltages NOT supported...skip %s\n",
	sreg->of_node->full_name);
	return -EOPNOTSUPP;
	}

	sreg->desc.name = devm_kasprintf(dev, GFP_KERNEL, "%s", vinfo->name);
	if (!sreg->desc.name)
	return -ENOMEM;

	sreg->desc.id = sreg->id;
	sreg->desc.type = REGULATOR_VOLTAGE;
	sreg->desc.owner = THIS_MODULE;
	sreg->desc.of_match_full_name = true;
	sreg->desc.of_match = sreg->of_node->full_name;
	sreg->desc.regulators_node = "regulators";
	if (vinfo->segmented)
	ret = scmi_config_linear_regulator_mappings(sreg, vinfo);
	else
	ret = scmi_config_discrete_regulator_mappings(sreg, vinfo);
	if (ret)
	return ret;

	/*
	* Using the scmi device here to have DT searched from Voltage
	* protocol node down.
	*/
	sreg->conf.dev = dev;

	/* Store for later retrieval via rdev_get_drvdata() */
	sreg->conf.driver_data = sreg;

	return 0;
	}

	static int process_scmi_regulator_of_node(struct scmi_device *sdev,
	struct device_node *np,
	struct scmi_regulator_info *rinfo)
	{
	u32 dom, ret;

	ret = of_property_read_u32(np, "reg", &dom);
	if (ret)
	return ret;

	if (dom >= rinfo->num_doms)
	return -ENODEV;

	if (rinfo->sregv[dom]) {
	dev_err(&sdev->dev,
	"SCMI Voltage Domain %d already in use. Skipping: %s\n",
	dom, np->full_name);
	return -EINVAL;
	}

	rinfo->sregv[dom] = devm_kzalloc(&sdev->dev,
	sizeof(struct scmi_regulator),
	GFP_KERNEL);
	if (!rinfo->sregv[dom])
	return -ENOMEM;

	rinfo->sregv[dom]->id = dom;
	rinfo->sregv[dom]->sdev = sdev;

	/* get hold of good nodes */
	of_node_get(np);
	rinfo->sregv[dom]->of_node = np;

	dev_dbg(&sdev->dev,
	"Found SCMI Regulator entry -- OF node [%d] -> %s\n",
	dom, np->full_name);

	return 0;
	}

	static int scmi_regulator_probe(struct scmi_device *sdev)
	{
	int d, ret, num_doms;
	struct device_node np, child;
	const struct scmi_handle *handle = sdev->handle;
	struct scmi_regulator_info *rinfo;

	if (!handle \|\| !handle->voltage_ops)
	return -ENODEV;

	num_doms = handle->voltage_ops->num_domains_get(handle);
	if (num_doms <= 0) {
	if (!num_doms) {
	dev_err(&sdev->dev,
	"number of voltage domains invalid\n");
	num_doms = -EINVAL;
	} else {
	dev_err(&sdev->dev,
	"failed to get voltage domains - err:%d\n",
	num_doms);
	}

	return num_doms;
	}

	rinfo = devm_kzalloc(&sdev->dev, sizeof(*rinfo), GFP_KERNEL);
	if (!rinfo)
	return -ENOMEM;

	/* Allocate pointers array for all possible domains */
	rinfo->sregv = devm_kcalloc(&sdev->dev, num_doms,
	sizeof(void *), GFP_KERNEL);
	if (!rinfo->sregv)
	return -ENOMEM;

	rinfo->num_doms = num_doms;

	/*
	* Start collecting into rinfo->sregv possibly good SCMI Regulators as
	* described by a well-formed DT entry and associated with an existing
	* plausible SCMI Voltage Domain number, all belonging to this SCMI
	* platform instance node (handle->dev->of_node).
	*/
	np = of_find_node_by_name(handle->dev->of_node, "regulators");
	for_each_child_of_node(np, child) {
	ret = process_scmi_regulator_of_node(sdev, child, rinfo);
	/* abort on any mem issue */
	if (ret == -ENOMEM)
	return ret;
	}

	/*
	* Register a regulator for each valid regulator-DT-entry that we
	* can successfully reach via SCMI and has a valid associated voltage
	* domain.
	*/
	for (d = 0; d < num_doms; d++) {
	struct scmi_regulator *sreg = rinfo->sregv[d];

	/* Skip empty slots */
	if (!sreg)
	continue;

	ret = scmi_regulator_common_init(sreg);
	/* Skip invalid voltage domains */
	if (ret)
	continue;

	sreg->rdev = devm_regulator_register(&sdev->dev, &sreg->desc,
	&sreg->conf);
	if (IS_ERR(sreg->rdev)) {
	sreg->rdev = NULL;
	continue;
	}

	dev_info(&sdev->dev,
	"Regulator %s registered for domain [%d]\n",
	sreg->desc.name, sreg->id);
	}

	dev_set_drvdata(&sdev->dev, rinfo);

	return 0;
	}

	static void scmi_regulator_remove(struct scmi_device *sdev)
	{
	int d;
	struct scmi_regulator_info *rinfo;

	rinfo = dev_get_drvdata(&sdev->dev);
	if (!rinfo)
	return;

	for (d = 0; d < rinfo->num_doms; d++) {
	if (!rinfo->sregv[d])
	continue;
	of_node_put(rinfo->sregv[d]->of_node);
	}
	}

	static const struct scmi_device_id scmi_regulator_id_table[] = {
	{ SCMI_PROTOCOL_VOLTAGE, "regulator" },
	{ },
	};
	MODULE_DEVICE_TABLE(scmi, scmi_regulator_id_table);

	static struct scmi_driver scmi_drv = {
	.name = "scmi-regulator",
	.probe = scmi_regulator_probe,
	.remove = scmi_regulator_remove,
	.id_table = scmi_regulator_id_table,
	};

	module_scmi_driver(scmi_drv);

	MODULE_AUTHOR("Cristian Marussi <cristian.marussi@arm.com>");
	MODULE_DESCRIPTION("ARM SCMI regulator driver");
	MODULE_LICENSE("GPL v2");