| /* |
| * drivers/mmc/host/sdhci-msm.c - Qualcomm Technologies, Inc. MSM SDHCI Platform |
| * driver source file |
| * |
| * Copyright (c) 2012-2019, The Linux Foundation. All rights reserved. |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License version 2 and |
| * only version 2 as published by the Free Software Foundation. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| * |
| */ |
| |
| #include <linux/module.h> |
| #include <linux/mmc/host.h> |
| #include <linux/mmc/card.h> |
| #include <linux/mmc/sdio_func.h> |
| #include <linux/gfp.h> |
| #include <linux/of.h> |
| #include <linux/of_device.h> |
| #include <linux/of_gpio.h> |
| #include <linux/regulator/consumer.h> |
| #include <linux/types.h> |
| #include <linux/input.h> |
| #include <linux/platform_device.h> |
| #include <linux/wait.h> |
| #include <linux/io.h> |
| #include <linux/delay.h> |
| #include <linux/scatterlist.h> |
| #include <linux/slab.h> |
| #include <linux/mmc/slot-gpio.h> |
| #include <linux/dma-mapping.h> |
| #include <linux/iopoll.h> |
| #include <linux/pinctrl/consumer.h> |
| #include <linux/iopoll.h> |
| #include <linux/msm-bus.h> |
| #include <linux/pm_runtime.h> |
| #include <linux/nvmem-consumer.h> |
| #include <trace/events/mmc.h> |
| |
| #include "sdhci-msm.h" |
| #include "sdhci-msm-ice.h" |
| #include "cmdq_hci.h" |
| |
| #define QOS_REMOVE_DELAY_MS 10 |
| #define CORE_POWER 0x0 |
| #define CORE_SW_RST (1 << 7) |
| |
| #define SDHCI_VER_100 0x2B |
| |
| #define CORE_VERSION_STEP_MASK 0x0000FFFF |
| #define CORE_VERSION_MINOR_MASK 0x0FFF0000 |
| #define CORE_VERSION_MINOR_SHIFT 16 |
| #define CORE_VERSION_MAJOR_MASK 0xF0000000 |
| #define CORE_VERSION_MAJOR_SHIFT 28 |
| #define CORE_VERSION_TARGET_MASK 0x000000FF |
| #define SDHCI_MSM_VER_420 0x49 |
| |
| #define SWITCHABLE_SIGNALLING_VOL (1 << 29) |
| |
| #define CORE_VERSION_MAJOR_MASK 0xF0000000 |
| #define CORE_VERSION_MAJOR_SHIFT 28 |
| |
| #define CORE_HC_MODE 0x78 |
| #define HC_MODE_EN 0x1 |
| #define FF_CLK_SW_RST_DIS (1 << 13) |
| |
| #define CORE_PWRCTL_BUS_OFF 0x01 |
| #define CORE_PWRCTL_BUS_ON (1 << 1) |
| #define CORE_PWRCTL_IO_LOW (1 << 2) |
| #define CORE_PWRCTL_IO_HIGH (1 << 3) |
| |
| #define CORE_PWRCTL_BUS_SUCCESS 0x01 |
| #define CORE_PWRCTL_BUS_FAIL (1 << 1) |
| #define CORE_PWRCTL_IO_SUCCESS (1 << 2) |
| #define CORE_PWRCTL_IO_FAIL (1 << 3) |
| |
| #define INT_MASK 0xF |
| #define MAX_PHASES 16 |
| |
| #define CORE_CMD_DAT_TRACK_SEL (1 << 0) |
| #define CORE_DLL_EN (1 << 16) |
| #define CORE_CDR_EN (1 << 17) |
| #define CORE_CK_OUT_EN (1 << 18) |
| #define CORE_CDR_EXT_EN (1 << 19) |
| #define CORE_DLL_PDN (1 << 29) |
| #define CORE_DLL_RST (1 << 30) |
| |
| #define CORE_DLL_LOCK (1 << 7) |
| #define CORE_DDR_DLL_LOCK (1 << 11) |
| |
| #define CORE_CLK_PWRSAVE (1 << 1) |
| #define CORE_VNDR_SPEC_ADMA_ERR_SIZE_EN (1 << 7) |
| #define CORE_HC_MCLK_SEL_DFLT (2 << 8) |
| #define CORE_HC_MCLK_SEL_HS400 (3 << 8) |
| #define CORE_HC_MCLK_SEL_MASK (3 << 8) |
| #define CORE_HC_AUTO_CMD21_EN (1 << 6) |
| #define CORE_IO_PAD_PWR_SWITCH_EN (1 << 15) |
| #define CORE_IO_PAD_PWR_SWITCH (1 << 16) |
| #define CORE_HC_SELECT_IN_EN (1 << 18) |
| #define CORE_HC_SELECT_IN_HS400 (6 << 19) |
| #define CORE_HC_SELECT_IN_MASK (7 << 19) |
| #define CORE_VENDOR_SPEC_POR_VAL 0xA1C |
| |
| #define HC_SW_RST_WAIT_IDLE_DIS (1 << 20) |
| #define HC_SW_RST_REQ (1 << 21) |
| #define CORE_ONE_MID_EN (1 << 25) |
| |
| #define CORE_8_BIT_SUPPORT (1 << 18) |
| #define CORE_3_3V_SUPPORT (1 << 24) |
| #define CORE_3_0V_SUPPORT (1 << 25) |
| #define CORE_1_8V_SUPPORT (1 << 26) |
| #define CORE_SYS_BUS_SUPPORT_64_BIT BIT(28) |
| |
| #define CORE_CSR_CDC_CTLR_CFG0 0x130 |
| #define CORE_SW_TRIG_FULL_CALIB (1 << 16) |
| #define CORE_HW_AUTOCAL_ENA (1 << 17) |
| |
| #define CORE_CSR_CDC_CTLR_CFG1 0x134 |
| #define CORE_CSR_CDC_CAL_TIMER_CFG0 0x138 |
| #define CORE_TIMER_ENA (1 << 16) |
| |
| #define CORE_CSR_CDC_CAL_TIMER_CFG1 0x13C |
| #define CORE_CSR_CDC_REFCOUNT_CFG 0x140 |
| #define CORE_CSR_CDC_COARSE_CAL_CFG 0x144 |
| #define CORE_CDC_OFFSET_CFG 0x14C |
| #define CORE_CSR_CDC_DELAY_CFG 0x150 |
| #define CORE_CDC_SLAVE_DDA_CFG 0x160 |
| #define CORE_CSR_CDC_STATUS0 0x164 |
| #define CORE_CALIBRATION_DONE (1 << 0) |
| |
| #define CORE_CDC_ERROR_CODE_MASK 0x7000000 |
| |
| #define CQ_CMD_DBG_RAM 0x110 |
| #define CQ_CMD_DBG_RAM_WA 0x150 |
| #define CQ_CMD_DBG_RAM_OL 0x154 |
| |
| #define CORE_CSR_CDC_GEN_CFG 0x178 |
| #define CORE_CDC_SWITCH_BYPASS_OFF (1 << 0) |
| #define CORE_CDC_SWITCH_RC_EN (1 << 1) |
| |
| #define CORE_CDC_T4_DLY_SEL (1 << 0) |
| #define CORE_CMDIN_RCLK_EN (1 << 1) |
| #define CORE_START_CDC_TRAFFIC (1 << 6) |
| |
| #define CORE_PWRSAVE_DLL (1 << 3) |
| #define CORE_FIFO_ALT_EN (1 << 10) |
| #define CORE_CMDEN_HS400_INPUT_MASK_CNT (1 << 13) |
| |
| #define CORE_DDR_CAL_EN (1 << 0) |
| #define CORE_FLL_CYCLE_CNT (1 << 18) |
| #define CORE_DLL_CLOCK_DISABLE (1 << 21) |
| |
| #define DDR_CONFIG_POR_VAL 0x80040873 |
| #define DLL_USR_CTL_POR_VAL 0x10800 |
| #define ENABLE_DLL_LOCK_STATUS (1 << 26) |
| #define FINE_TUNE_MODE_EN (1 << 27) |
| #define BIAS_OK_SIGNAL (1 << 29) |
| #define DLL_CONFIG_3_POR_VAL 0x10 |
| |
| /* 512 descriptors */ |
| #define SDHCI_MSM_MAX_SEGMENTS (1 << 9) |
| #define SDHCI_MSM_MMC_CLK_GATE_DELAY 200 /* msecs */ |
| |
| #define CORE_FREQ_100MHZ (100 * 1000 * 1000) |
| #define TCXO_FREQ 19200000 |
| |
| #define INVALID_TUNING_PHASE -1 |
| #define sdhci_is_valid_gpio_wakeup_int(_h) ((_h)->pdata->sdiowakeup_irq >= 0) |
| |
| #define NUM_TUNING_PHASES 16 |
| #define MAX_DRV_TYPES_SUPPORTED_HS200 4 |
| #define MSM_AUTOSUSPEND_DELAY_MS 100 |
| |
| #define RCLK_TOGGLE 0x2 |
| |
| struct sdhci_msm_offset { |
| u32 CORE_MCI_DATA_CNT; |
| u32 CORE_MCI_STATUS; |
| u32 CORE_MCI_FIFO_CNT; |
| u32 CORE_MCI_VERSION; |
| u32 CORE_GENERICS; |
| u32 CORE_TESTBUS_CONFIG; |
| u32 CORE_TESTBUS_SEL2_BIT; |
| u32 CORE_TESTBUS_ENA; |
| u32 CORE_TESTBUS_SEL2; |
| u32 CORE_PWRCTL_STATUS; |
| u32 CORE_PWRCTL_MASK; |
| u32 CORE_PWRCTL_CLEAR; |
| u32 CORE_PWRCTL_CTL; |
| u32 CORE_SDCC_DEBUG_REG; |
| u32 CORE_DLL_CONFIG; |
| u32 CORE_DLL_STATUS; |
| u32 CORE_VENDOR_SPEC; |
| u32 CORE_VENDOR_SPEC_ADMA_ERR_ADDR0; |
| u32 CORE_VENDOR_SPEC_ADMA_ERR_ADDR1; |
| u32 CORE_VENDOR_SPEC_FUNC2; |
| u32 CORE_VENDOR_SPEC_CAPABILITIES0; |
| u32 CORE_DDR_200_CFG; |
| u32 CORE_VENDOR_SPEC3; |
| u32 CORE_DLL_CONFIG_2; |
| u32 CORE_DLL_CONFIG_3; |
| u32 CORE_DDR_CONFIG; |
| u32 CORE_DDR_CONFIG_OLD; /* Applcable to sddcc minor ver < 0x49 only */ |
| u32 CORE_DLL_USR_CTL; /* Present on SDCC5.1 onwards */ |
| }; |
| |
| struct sdhci_msm_offset sdhci_msm_offset_mci_removed = { |
| .CORE_MCI_DATA_CNT = 0x35C, |
| .CORE_MCI_STATUS = 0x324, |
| .CORE_MCI_FIFO_CNT = 0x308, |
| .CORE_MCI_VERSION = 0x318, |
| .CORE_GENERICS = 0x320, |
| .CORE_TESTBUS_CONFIG = 0x32C, |
| .CORE_TESTBUS_SEL2_BIT = 3, |
| .CORE_TESTBUS_ENA = (1 << 31), |
| .CORE_TESTBUS_SEL2 = (1 << 3), |
| .CORE_PWRCTL_STATUS = 0x240, |
| .CORE_PWRCTL_MASK = 0x244, |
| .CORE_PWRCTL_CLEAR = 0x248, |
| .CORE_PWRCTL_CTL = 0x24C, |
| .CORE_SDCC_DEBUG_REG = 0x358, |
| .CORE_DLL_CONFIG = 0x200, |
| .CORE_DLL_STATUS = 0x208, |
| .CORE_VENDOR_SPEC = 0x20C, |
| .CORE_VENDOR_SPEC_ADMA_ERR_ADDR0 = 0x214, |
| .CORE_VENDOR_SPEC_ADMA_ERR_ADDR1 = 0x218, |
| .CORE_VENDOR_SPEC_FUNC2 = 0x210, |
| .CORE_VENDOR_SPEC_CAPABILITIES0 = 0x21C, |
| .CORE_DDR_200_CFG = 0x224, |
| .CORE_VENDOR_SPEC3 = 0x250, |
| .CORE_DLL_CONFIG_2 = 0x254, |
| .CORE_DLL_CONFIG_3 = 0x258, |
| .CORE_DDR_CONFIG = 0x25C, |
| .CORE_DLL_USR_CTL = 0x388, |
| }; |
| |
| struct sdhci_msm_offset sdhci_msm_offset_mci_present = { |
| .CORE_MCI_DATA_CNT = 0x30, |
| .CORE_MCI_STATUS = 0x34, |
| .CORE_MCI_FIFO_CNT = 0x44, |
| .CORE_MCI_VERSION = 0x050, |
| .CORE_GENERICS = 0x70, |
| .CORE_TESTBUS_CONFIG = 0x0CC, |
| .CORE_TESTBUS_SEL2_BIT = 4, |
| .CORE_TESTBUS_ENA = (1 << 3), |
| .CORE_TESTBUS_SEL2 = (1 << 4), |
| .CORE_PWRCTL_STATUS = 0xDC, |
| .CORE_PWRCTL_MASK = 0xE0, |
| .CORE_PWRCTL_CLEAR = 0xE4, |
| .CORE_PWRCTL_CTL = 0xE8, |
| .CORE_SDCC_DEBUG_REG = 0x124, |
| .CORE_DLL_CONFIG = 0x100, |
| .CORE_DLL_STATUS = 0x108, |
| .CORE_VENDOR_SPEC = 0x10C, |
| .CORE_VENDOR_SPEC_ADMA_ERR_ADDR0 = 0x114, |
| .CORE_VENDOR_SPEC_ADMA_ERR_ADDR1 = 0x118, |
| .CORE_VENDOR_SPEC_FUNC2 = 0x110, |
| .CORE_VENDOR_SPEC_CAPABILITIES0 = 0x11C, |
| .CORE_DDR_200_CFG = 0x184, |
| .CORE_VENDOR_SPEC3 = 0x1B0, |
| .CORE_DLL_CONFIG_2 = 0x1B4, |
| .CORE_DLL_CONFIG_3 = 0x1B8, |
| .CORE_DDR_CONFIG_OLD = 0x1B8, /* Applicable to sdcc minor ver < 0x49 */ |
| .CORE_DDR_CONFIG = 0x1BC, |
| }; |
| |
| u8 sdhci_msm_readb_relaxed(struct sdhci_host *host, u32 offset) |
| { |
| struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); |
| struct sdhci_msm_host *msm_host = pltfm_host->priv; |
| void __iomem *base_addr; |
| |
| if (msm_host->mci_removed) |
| base_addr = host->ioaddr; |
| else |
| base_addr = msm_host->core_mem; |
| |
| return readb_relaxed(base_addr + offset); |
| } |
| |
| u32 sdhci_msm_readl_relaxed(struct sdhci_host *host, u32 offset) |
| { |
| struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); |
| struct sdhci_msm_host *msm_host = pltfm_host->priv; |
| void __iomem *base_addr; |
| |
| if (msm_host->mci_removed) |
| base_addr = host->ioaddr; |
| else |
| base_addr = msm_host->core_mem; |
| |
| return readl_relaxed(base_addr + offset); |
| } |
| |
| void sdhci_msm_writeb_relaxed(u8 val, struct sdhci_host *host, u32 offset) |
| { |
| struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); |
| struct sdhci_msm_host *msm_host = pltfm_host->priv; |
| void __iomem *base_addr; |
| |
| if (msm_host->mci_removed) |
| base_addr = host->ioaddr; |
| else |
| base_addr = msm_host->core_mem; |
| |
| writeb_relaxed(val, base_addr + offset); |
| } |
| |
| void sdhci_msm_writel_relaxed(u32 val, struct sdhci_host *host, u32 offset) |
| { |
| struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); |
| struct sdhci_msm_host *msm_host = pltfm_host->priv; |
| void __iomem *base_addr; |
| |
| if (msm_host->mci_removed) |
| base_addr = host->ioaddr; |
| else |
| base_addr = msm_host->core_mem; |
| |
| writel_relaxed(val, base_addr + offset); |
| } |
| |
| /* Timeout value to avoid infinite waiting for pwr_irq */ |
| #define MSM_PWR_IRQ_TIMEOUT_MS 5000 |
| |
| static const u32 tuning_block_64[] = { |
| 0x00FF0FFF, 0xCCC3CCFF, 0xFFCC3CC3, 0xEFFEFFFE, |
| 0xDDFFDFFF, 0xFBFFFBFF, 0xFF7FFFBF, 0xEFBDF777, |
| 0xF0FFF0FF, 0x3CCCFC0F, 0xCFCC33CC, 0xEEFFEFFF, |
| 0xFDFFFDFF, 0xFFBFFFDF, 0xFFF7FFBB, 0xDE7B7FF7 |
| }; |
| |
| static const u32 tuning_block_128[] = { |
| 0xFF00FFFF, 0x0000FFFF, 0xCCCCFFFF, 0xCCCC33CC, |
| 0xCC3333CC, 0xFFFFCCCC, 0xFFFFEEFF, 0xFFEEEEFF, |
| 0xFFDDFFFF, 0xDDDDFFFF, 0xBBFFFFFF, 0xBBFFFFFF, |
| 0xFFFFFFBB, 0xFFFFFF77, 0x77FF7777, 0xFFEEDDBB, |
| 0x00FFFFFF, 0x00FFFFFF, 0xCCFFFF00, 0xCC33CCCC, |
| 0x3333CCCC, 0xFFCCCCCC, 0xFFEEFFFF, 0xEEEEFFFF, |
| 0xDDFFFFFF, 0xDDFFFFFF, 0xFFFFFFDD, 0xFFFFFFBB, |
| 0xFFFFBBBB, 0xFFFF77FF, 0xFF7777FF, 0xEEDDBB77 |
| }; |
| |
| /* global to hold each slot instance for debug */ |
| static struct sdhci_msm_host *sdhci_slot[2]; |
| |
| static int disable_slots; |
| /* root can write, others read */ |
| module_param(disable_slots, int, S_IRUGO|S_IWUSR); |
| |
| static bool nocmdq; |
| module_param(nocmdq, bool, S_IRUGO|S_IWUSR); |
| |
| enum vdd_io_level { |
| /* set vdd_io_data->low_vol_level */ |
| VDD_IO_LOW, |
| /* set vdd_io_data->high_vol_level */ |
| VDD_IO_HIGH, |
| /* |
| * set whatever there in voltage_level (third argument) of |
| * sdhci_msm_set_vdd_io_vol() function. |
| */ |
| VDD_IO_SET_LEVEL, |
| }; |
| |
| enum dll_init_context { |
| DLL_INIT_NORMAL = 0, |
| DLL_INIT_FROM_CX_COLLAPSE_EXIT, |
| }; |
| |
| static unsigned int sdhci_msm_get_sup_clk_rate(struct sdhci_host *host, |
| u32 req_clk); |
| |
| /* MSM platform specific tuning */ |
| static inline int msm_dll_poll_ck_out_en(struct sdhci_host *host, |
| u8 poll) |
| { |
| int rc = 0; |
| u32 wait_cnt = 50; |
| u8 ck_out_en = 0; |
| struct mmc_host *mmc = host->mmc; |
| struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); |
| struct sdhci_msm_host *msm_host = pltfm_host->priv; |
| const struct sdhci_msm_offset *msm_host_offset = |
| msm_host->offset; |
| |
| /* poll for CK_OUT_EN bit. max. poll time = 50us */ |
| ck_out_en = !!(readl_relaxed(host->ioaddr + |
| msm_host_offset->CORE_DLL_CONFIG) & CORE_CK_OUT_EN); |
| |
| while (ck_out_en != poll) { |
| if (--wait_cnt == 0) { |
| pr_err("%s: %s: CK_OUT_EN bit is not %d\n", |
| mmc_hostname(mmc), __func__, poll); |
| rc = -ETIMEDOUT; |
| goto out; |
| } |
| udelay(1); |
| |
| ck_out_en = !!(readl_relaxed(host->ioaddr + |
| msm_host_offset->CORE_DLL_CONFIG) & CORE_CK_OUT_EN); |
| } |
| out: |
| return rc; |
| } |
| |
| /* |
| * Enable CDR to track changes of DAT lines and adjust sampling |
| * point according to voltage/temperature variations |
| */ |
| static int msm_enable_cdr_cm_sdc4_dll(struct sdhci_host *host) |
| { |
| int rc = 0; |
| u32 config; |
| struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); |
| struct sdhci_msm_host *msm_host = pltfm_host->priv; |
| const struct sdhci_msm_offset *msm_host_offset = |
| msm_host->offset; |
| |
| config = readl_relaxed(host->ioaddr + |
| msm_host_offset->CORE_DLL_CONFIG); |
| config |= CORE_CDR_EN; |
| config &= ~(CORE_CDR_EXT_EN | CORE_CK_OUT_EN); |
| writel_relaxed(config, host->ioaddr + |
| msm_host_offset->CORE_DLL_CONFIG); |
| |
| rc = msm_dll_poll_ck_out_en(host, 0); |
| if (rc) |
| goto err; |
| |
| writel_relaxed((readl_relaxed(host->ioaddr + |
| msm_host_offset->CORE_DLL_CONFIG) | CORE_CK_OUT_EN), |
| host->ioaddr + msm_host_offset->CORE_DLL_CONFIG); |
| |
| rc = msm_dll_poll_ck_out_en(host, 1); |
| if (rc) |
| goto err; |
| goto out; |
| err: |
| pr_err("%s: %s: failed\n", mmc_hostname(host->mmc), __func__); |
| out: |
| return rc; |
| } |
| |
| static ssize_t store_auto_cmd21(struct device *dev, struct device_attribute |
| *attr, const char *buf, size_t count) |
| { |
| struct sdhci_host *host = dev_get_drvdata(dev); |
| struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); |
| struct sdhci_msm_host *msm_host = pltfm_host->priv; |
| u32 tmp; |
| unsigned long flags; |
| |
| if (!kstrtou32(buf, 0, &tmp)) { |
| spin_lock_irqsave(&host->lock, flags); |
| msm_host->en_auto_cmd21 = !!tmp; |
| spin_unlock_irqrestore(&host->lock, flags); |
| } |
| return count; |
| } |
| |
| static ssize_t show_auto_cmd21(struct device *dev, |
| struct device_attribute *attr, char *buf) |
| { |
| struct sdhci_host *host = dev_get_drvdata(dev); |
| struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); |
| struct sdhci_msm_host *msm_host = pltfm_host->priv; |
| |
| return snprintf(buf, PAGE_SIZE, "%d\n", msm_host->en_auto_cmd21); |
| } |
| |
| /* MSM auto-tuning handler */ |
| static int sdhci_msm_config_auto_tuning_cmd(struct sdhci_host *host, |
| bool enable, |
| u32 type) |
| { |
| int rc = 0; |
| struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); |
| struct sdhci_msm_host *msm_host = pltfm_host->priv; |
| const struct sdhci_msm_offset *msm_host_offset = |
| msm_host->offset; |
| u32 val = 0; |
| |
| if (!msm_host->en_auto_cmd21) |
| return 0; |
| |
| if (type == MMC_SEND_TUNING_BLOCK_HS200) |
| val = CORE_HC_AUTO_CMD21_EN; |
| else |
| return 0; |
| |
| if (enable) { |
| rc = msm_enable_cdr_cm_sdc4_dll(host); |
| writel_relaxed(readl_relaxed(host->ioaddr + |
| msm_host_offset->CORE_VENDOR_SPEC) | val, |
| host->ioaddr + msm_host_offset->CORE_VENDOR_SPEC); |
| } else { |
| writel_relaxed(readl_relaxed(host->ioaddr + |
| msm_host_offset->CORE_VENDOR_SPEC) & ~val, |
| host->ioaddr + msm_host_offset->CORE_VENDOR_SPEC); |
| } |
| return rc; |
| } |
| |
| static int msm_config_cm_dll_phase(struct sdhci_host *host, u8 phase) |
| { |
| int rc = 0; |
| struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); |
| struct sdhci_msm_host *msm_host = pltfm_host->priv; |
| const struct sdhci_msm_offset *msm_host_offset = |
| msm_host->offset; |
| u8 grey_coded_phase_table[] = {0x0, 0x1, 0x3, 0x2, 0x6, 0x7, 0x5, 0x4, |
| 0xC, 0xD, 0xF, 0xE, 0xA, 0xB, 0x9, |
| 0x8}; |
| unsigned long flags; |
| u32 config; |
| struct mmc_host *mmc = host->mmc; |
| |
| pr_debug("%s: Enter %s\n", mmc_hostname(mmc), __func__); |
| spin_lock_irqsave(&host->lock, flags); |
| |
| config = readl_relaxed(host->ioaddr + |
| msm_host_offset->CORE_DLL_CONFIG); |
| config &= ~(CORE_CDR_EN | CORE_CK_OUT_EN); |
| config |= (CORE_CDR_EXT_EN | CORE_DLL_EN); |
| writel_relaxed(config, host->ioaddr + |
| msm_host_offset->CORE_DLL_CONFIG); |
| |
| /* Wait until CK_OUT_EN bit of DLL_CONFIG register becomes '0' */ |
| rc = msm_dll_poll_ck_out_en(host, 0); |
| if (rc) |
| goto err_out; |
| |
| /* |
| * Write the selected DLL clock output phase (0 ... 15) |
| * to CDR_SELEXT bit field of DLL_CONFIG register. |
| */ |
| if (msm_host->dll_hsr->dll_config & (0xF << 20)) { |
| writel_relaxed(((readl_relaxed(host->ioaddr + |
| msm_host_offset->CORE_DLL_CONFIG) |
| & ~(0xF << 20)) |
| | (grey_coded_phase_table[phase] << 20)), |
| host->ioaddr + msm_host_offset->CORE_DLL_CONFIG); |
| } |
| |
| /* Set CK_OUT_EN bit of DLL_CONFIG register to 1. */ |
| writel_relaxed((readl_relaxed(host->ioaddr + |
| msm_host_offset->CORE_DLL_CONFIG) | CORE_CK_OUT_EN), |
| host->ioaddr + msm_host_offset->CORE_DLL_CONFIG); |
| |
| /* Wait until CK_OUT_EN bit of DLL_CONFIG register becomes '1' */ |
| rc = msm_dll_poll_ck_out_en(host, 1); |
| if (rc) |
| goto err_out; |
| |
| config = readl_relaxed(host->ioaddr + |
| msm_host_offset->CORE_DLL_CONFIG); |
| config |= CORE_CDR_EN; |
| config &= ~CORE_CDR_EXT_EN; |
| writel_relaxed(config, host->ioaddr + |
| msm_host_offset->CORE_DLL_CONFIG); |
| goto out; |
| |
| err_out: |
| pr_err("%s: %s: Failed to set DLL phase: %d\n", |
| mmc_hostname(mmc), __func__, phase); |
| out: |
| spin_unlock_irqrestore(&host->lock, flags); |
| pr_debug("%s: Exit %s\n", mmc_hostname(mmc), __func__); |
| return rc; |
| } |
| |
| /* |
| * Find out the greatest range of consecuitive selected |
| * DLL clock output phases that can be used as sampling |
| * setting for SD3.0 UHS-I card read operation (in SDR104 |
| * timing mode) or for eMMC4.5 card read operation (in |
| * HS400/HS200 timing mode). |
| * Select the 3/4 of the range and configure the DLL with the |
| * selected DLL clock output phase. |
| */ |
| |
| static int msm_find_most_appropriate_phase(struct sdhci_host *host, |
| u8 *phase_table, u8 total_phases) |
| { |
| int ret; |
| u8 ranges[MAX_PHASES][MAX_PHASES] = { {0}, {0} }; |
| u8 phases_per_row[MAX_PHASES] = {0}; |
| int row_index = 0, col_index = 0, selected_row_index = 0, curr_max = 0; |
| int i, cnt, phase_0_raw_index = 0, phase_15_raw_index = 0; |
| bool phase_0_found = false, phase_15_found = false; |
| struct mmc_host *mmc = host->mmc; |
| |
| pr_debug("%s: Enter %s\n", mmc_hostname(mmc), __func__); |
| if (!total_phases || (total_phases > MAX_PHASES)) { |
| pr_err("%s: %s: invalid argument: total_phases=%d\n", |
| mmc_hostname(mmc), __func__, total_phases); |
| return -EINVAL; |
| } |
| |
| for (cnt = 0; cnt < total_phases; cnt++) { |
| ranges[row_index][col_index] = phase_table[cnt]; |
| phases_per_row[row_index] += 1; |
| col_index++; |
| |
| if ((cnt + 1) == total_phases) { |
| continue; |
| /* check if next phase in phase_table is consecutive or not */ |
| } else if ((phase_table[cnt] + 1) != phase_table[cnt + 1]) { |
| row_index++; |
| col_index = 0; |
| } |
| } |
| |
| if (row_index >= MAX_PHASES) |
| return -EINVAL; |
| |
| /* Check if phase-0 is present in first valid window? */ |
| if (!ranges[0][0]) { |
| phase_0_found = true; |
| phase_0_raw_index = 0; |
| /* Check if cycle exist between 2 valid windows */ |
| for (cnt = 1; cnt <= row_index; cnt++) { |
| if (phases_per_row[cnt]) { |
| for (i = 0; i < phases_per_row[cnt]; i++) { |
| if (ranges[cnt][i] == 15) { |
| phase_15_found = true; |
| phase_15_raw_index = cnt; |
| break; |
| } |
| } |
| } |
| } |
| } |
| |
| /* If 2 valid windows form cycle then merge them as single window */ |
| if (phase_0_found && phase_15_found) { |
| /* number of phases in raw where phase 0 is present */ |
| u8 phases_0 = phases_per_row[phase_0_raw_index]; |
| /* number of phases in raw where phase 15 is present */ |
| u8 phases_15 = phases_per_row[phase_15_raw_index]; |
| |
| if (phases_0 + phases_15 >= MAX_PHASES) |
| /* |
| * If there are more than 1 phase windows then total |
| * number of phases in both the windows should not be |
| * more than or equal to MAX_PHASES. |
| */ |
| return -EINVAL; |
| |
| /* Merge 2 cyclic windows */ |
| i = phases_15; |
| for (cnt = 0; cnt < phases_0; cnt++) { |
| ranges[phase_15_raw_index][i] = |
| ranges[phase_0_raw_index][cnt]; |
| if (++i >= MAX_PHASES) |
| break; |
| } |
| |
| phases_per_row[phase_0_raw_index] = 0; |
| phases_per_row[phase_15_raw_index] = phases_15 + phases_0; |
| } |
| |
| for (cnt = 0; cnt <= row_index; cnt++) { |
| if (phases_per_row[cnt] > curr_max) { |
| curr_max = phases_per_row[cnt]; |
| selected_row_index = cnt; |
| } |
| } |
| |
| i = ((curr_max * 3) / 4); |
| if (i) |
| i--; |
| |
| ret = (int)ranges[selected_row_index][i]; |
| |
| if (ret >= MAX_PHASES) { |
| ret = -EINVAL; |
| pr_err("%s: %s: invalid phase selected=%d\n", |
| mmc_hostname(mmc), __func__, ret); |
| } |
| |
| pr_debug("%s: Exit %s\n", mmc_hostname(mmc), __func__); |
| return ret; |
| } |
| |
| static inline void msm_cm_dll_set_freq(struct sdhci_host *host) |
| { |
| u32 mclk_freq = 0; |
| struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); |
| struct sdhci_msm_host *msm_host = pltfm_host->priv; |
| const struct sdhci_msm_offset *msm_host_offset = |
| msm_host->offset; |
| |
| /* Program the MCLK value to MCLK_FREQ bit field */ |
| if (host->clock <= 112000000) |
| mclk_freq = 0; |
| else if (host->clock <= 125000000) |
| mclk_freq = 1; |
| else if (host->clock <= 137000000) |
| mclk_freq = 2; |
| else if (host->clock <= 150000000) |
| mclk_freq = 3; |
| else if (host->clock <= 162000000) |
| mclk_freq = 4; |
| else if (host->clock <= 175000000) |
| mclk_freq = 5; |
| else if (host->clock <= 187000000) |
| mclk_freq = 6; |
| else if (host->clock <= 208000000) |
| mclk_freq = 7; |
| |
| writel_relaxed(((readl_relaxed(host->ioaddr + |
| msm_host_offset->CORE_DLL_CONFIG) |
| & ~(7 << 24)) | (mclk_freq << 24)), |
| host->ioaddr + msm_host_offset->CORE_DLL_CONFIG); |
| } |
| |
| /* Initialize the DLL (Programmable Delay Line ) */ |
| static int msm_init_cm_dll(struct sdhci_host *host, |
| enum dll_init_context init_context) |
| { |
| struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); |
| struct sdhci_msm_host *msm_host = pltfm_host->priv; |
| const struct sdhci_msm_offset *msm_host_offset = |
| msm_host->offset; |
| struct mmc_host *mmc = host->mmc; |
| int rc = 0; |
| unsigned long flags; |
| u32 wait_cnt; |
| bool prev_pwrsave, curr_pwrsave; |
| |
| pr_debug("%s: Enter %s\n", mmc_hostname(mmc), __func__); |
| spin_lock_irqsave(&host->lock, flags); |
| prev_pwrsave = !!(readl_relaxed(host->ioaddr + |
| msm_host_offset->CORE_VENDOR_SPEC) & CORE_CLK_PWRSAVE); |
| curr_pwrsave = prev_pwrsave; |
| /* |
| * Make sure that clock is always enabled when DLL |
| * tuning is in progress. Keeping PWRSAVE ON may |
| * turn off the clock. So let's disable the PWRSAVE |
| * here and re-enable it once tuning is completed. |
| */ |
| if (prev_pwrsave) { |
| writel_relaxed((readl_relaxed(host->ioaddr + |
| msm_host_offset->CORE_VENDOR_SPEC) |
| & ~CORE_CLK_PWRSAVE), host->ioaddr + |
| msm_host_offset->CORE_VENDOR_SPEC); |
| curr_pwrsave = false; |
| } |
| |
| if (msm_host->use_updated_dll_reset) { |
| /* Disable the DLL clock */ |
| writel_relaxed((readl_relaxed(host->ioaddr + |
| msm_host_offset->CORE_DLL_CONFIG) |
| & ~CORE_CK_OUT_EN), host->ioaddr + |
| msm_host_offset->CORE_DLL_CONFIG); |
| |
| writel_relaxed((readl_relaxed(host->ioaddr + |
| msm_host_offset->CORE_DLL_CONFIG_2) |
| | CORE_DLL_CLOCK_DISABLE), host->ioaddr + |
| msm_host_offset->CORE_DLL_CONFIG_2); |
| } |
| |
| /* Write 1 to DLL_RST bit of DLL_CONFIG register */ |
| writel_relaxed((readl_relaxed(host->ioaddr + |
| msm_host_offset->CORE_DLL_CONFIG) | CORE_DLL_RST), |
| host->ioaddr + msm_host_offset->CORE_DLL_CONFIG); |
| |
| /* Write 1 to DLL_PDN bit of DLL_CONFIG register */ |
| writel_relaxed((readl_relaxed(host->ioaddr + |
| msm_host_offset->CORE_DLL_CONFIG) | CORE_DLL_PDN), |
| host->ioaddr + msm_host_offset->CORE_DLL_CONFIG); |
| |
| if (msm_host->use_updated_dll_reset) { |
| u32 mclk_freq = 0; |
| u32 actual_clk = sdhci_msm_get_sup_clk_rate(host, host->clock); |
| |
| /* |
| * Only configure the mclk_freq in normal DLL init |
| * context. If the DLL init is coming from |
| * CX Collapse Exit context, the host->clock may be zero. |
| * The DLL_CONFIG_2 register has already been restored to |
| * proper value prior to getting here. |
| */ |
| if (init_context == DLL_INIT_NORMAL) { |
| switch (actual_clk) { |
| case 202000000: |
| case 201500000: |
| case 200000000: |
| mclk_freq = 42; |
| break; |
| case 192000000: |
| mclk_freq = 40; |
| break; |
| default: |
| mclk_freq = (u32)((actual_clk / TCXO_FREQ) * 4); |
| pr_info_once("%s: %s: Non standard clk freq =%u\n", |
| mmc_hostname(mmc), __func__, actual_clk); |
| } |
| |
| if ((readl_relaxed(host->ioaddr + |
| msm_host_offset->CORE_DLL_CONFIG_2) |
| & CORE_FLL_CYCLE_CNT)) |
| mclk_freq *= 2; |
| |
| writel_relaxed(((readl_relaxed(host->ioaddr + |
| msm_host_offset->CORE_DLL_CONFIG_2) |
| & ~(0xFF << 10)) | (mclk_freq << 10)), |
| host->ioaddr + msm_host_offset->CORE_DLL_CONFIG_2); |
| } |
| /* wait for 5us before enabling DLL clock */ |
| udelay(5); |
| } |
| |
| /* Write 0 to DLL_RST bit of DLL_CONFIG register */ |
| writel_relaxed((readl_relaxed(host->ioaddr + |
| msm_host_offset->CORE_DLL_CONFIG) & ~CORE_DLL_RST), |
| host->ioaddr + msm_host_offset->CORE_DLL_CONFIG); |
| |
| /* Write 0 to DLL_PDN bit of DLL_CONFIG register */ |
| writel_relaxed((readl_relaxed(host->ioaddr + |
| msm_host_offset->CORE_DLL_CONFIG) & ~CORE_DLL_PDN), |
| host->ioaddr + msm_host_offset->CORE_DLL_CONFIG); |
| |
| if (msm_host->use_updated_dll_reset) { |
| /* Enable the DLL clock */ |
| writel_relaxed((readl_relaxed(host->ioaddr + |
| msm_host_offset->CORE_DLL_CONFIG_2) |
| & ~CORE_DLL_CLOCK_DISABLE), host->ioaddr + |
| msm_host_offset->CORE_DLL_CONFIG_2); |
| } |
| |
| /* |
| * Configure DLL user control register to enable DLL status |
| * This setting is applicable to SDCC v5.1 onwards only. |
| * |
| * Configure Tassadar DLL (Only applicable for 7FF projects) |
| * |
| */ |
| if (msm_host->need_dll_user_ctl) { |
| if (msm_host->dll_hsr) { |
| writel_relaxed(msm_host->dll_hsr->dll_usr_ctl, |
| host->ioaddr + |
| msm_host_offset->CORE_DLL_USR_CTL); |
| writel_relaxed(msm_host->dll_hsr->dll_config_3, |
| host->ioaddr + |
| msm_host_offset->CORE_DLL_CONFIG_3); |
| } else { |
| writel_relaxed(DLL_USR_CTL_POR_VAL | FINE_TUNE_MODE_EN | |
| ENABLE_DLL_LOCK_STATUS | BIAS_OK_SIGNAL, |
| host->ioaddr + |
| msm_host_offset->CORE_DLL_USR_CTL); |
| |
| writel_relaxed(DLL_CONFIG_3_POR_VAL, host->ioaddr + |
| msm_host_offset->CORE_DLL_CONFIG_3); |
| } |
| } |
| |
| /* |
| * Update the lower byte of DLL_CONFIG only with HSR values. |
| * Since these are the static settings. |
| */ |
| if (msm_host->dll_hsr) { |
| writel_relaxed(((readl_relaxed(host->ioaddr + |
| msm_host_offset->CORE_DLL_CONFIG) & (~0xff)) | |
| (msm_host->dll_hsr->dll_config & 0xff)), |
| host->ioaddr + msm_host_offset->CORE_DLL_CONFIG); |
| } |
| |
| /* Set DLL_EN bit to 1. */ |
| writel_relaxed((readl_relaxed(host->ioaddr + |
| msm_host_offset->CORE_DLL_CONFIG) | CORE_DLL_EN), |
| host->ioaddr + msm_host_offset->CORE_DLL_CONFIG); |
| |
| /* Set CK_OUT_EN bit to 1. */ |
| writel_relaxed((readl_relaxed(host->ioaddr + |
| msm_host_offset->CORE_DLL_CONFIG) |
| | CORE_CK_OUT_EN), host->ioaddr + |
| msm_host_offset->CORE_DLL_CONFIG); |
| |
| wait_cnt = 50; |
| /* Wait until DLL_LOCK bit of DLL_STATUS register becomes '1' */ |
| while (!(readl_relaxed(host->ioaddr + |
| msm_host_offset->CORE_DLL_STATUS) & CORE_DLL_LOCK)) { |
| /* max. wait for 50us sec for LOCK bit to be set */ |
| if (--wait_cnt == 0) { |
| pr_err("%s: %s: DLL failed to LOCK\n", |
| mmc_hostname(mmc), __func__); |
| rc = -ETIMEDOUT; |
| goto out; |
| } |
| /* wait for 1us before polling again */ |
| udelay(1); |
| } |
| |
| out: |
| /* Restore the correct PWRSAVE state */ |
| if (prev_pwrsave ^ curr_pwrsave) { |
| u32 reg = readl_relaxed(host->ioaddr + |
| msm_host_offset->CORE_VENDOR_SPEC); |
| |
| if (prev_pwrsave) |
| reg |= CORE_CLK_PWRSAVE; |
| else |
| reg &= ~CORE_CLK_PWRSAVE; |
| |
| writel_relaxed(reg, host->ioaddr + |
| msm_host_offset->CORE_VENDOR_SPEC); |
| } |
| |
| spin_unlock_irqrestore(&host->lock, flags); |
| pr_debug("%s: Exit %s\n", mmc_hostname(mmc), __func__); |
| return rc; |
| } |
| |
| static int sdhci_msm_cdclp533_calibration(struct sdhci_host *host) |
| { |
| u32 calib_done; |
| int ret = 0; |
| int cdc_err = 0; |
| struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); |
| struct sdhci_msm_host *msm_host = pltfm_host->priv; |
| const struct sdhci_msm_offset *msm_host_offset = |
| msm_host->offset; |
| |
| pr_debug("%s: Enter %s\n", mmc_hostname(host->mmc), __func__); |
| |
| /* Write 0 to CDC_T4_DLY_SEL field in VENDOR_SPEC_DDR200_CFG */ |
| writel_relaxed((readl_relaxed(host->ioaddr + |
| msm_host_offset->CORE_DDR_200_CFG) |
| & ~CORE_CDC_T4_DLY_SEL), |
| host->ioaddr + msm_host_offset->CORE_DDR_200_CFG); |
| |
| /* Write 0 to CDC_SWITCH_BYPASS_OFF field in CORE_CSR_CDC_GEN_CFG */ |
| writel_relaxed((readl_relaxed(host->ioaddr + CORE_CSR_CDC_GEN_CFG) |
| & ~CORE_CDC_SWITCH_BYPASS_OFF), |
| host->ioaddr + CORE_CSR_CDC_GEN_CFG); |
| |
| /* Write 1 to CDC_SWITCH_RC_EN field in CORE_CSR_CDC_GEN_CFG */ |
| writel_relaxed((readl_relaxed(host->ioaddr + CORE_CSR_CDC_GEN_CFG) |
| | CORE_CDC_SWITCH_RC_EN), |
| host->ioaddr + CORE_CSR_CDC_GEN_CFG); |
| |
| /* Write 0 to START_CDC_TRAFFIC field in CORE_DDR200_CFG */ |
| writel_relaxed((readl_relaxed(host->ioaddr + |
| msm_host_offset->CORE_DDR_200_CFG) |
| & ~CORE_START_CDC_TRAFFIC), |
| host->ioaddr + msm_host_offset->CORE_DDR_200_CFG); |
| |
| /* |
| * Perform CDC Register Initialization Sequence |
| * |
| * CORE_CSR_CDC_CTLR_CFG0 0x11800EC |
| * CORE_CSR_CDC_CTLR_CFG1 0x3011111 |
| * CORE_CSR_CDC_CAL_TIMER_CFG0 0x1201000 |
| * CORE_CSR_CDC_CAL_TIMER_CFG1 0x4 |
| * CORE_CSR_CDC_REFCOUNT_CFG 0xCB732020 |
| * CORE_CSR_CDC_COARSE_CAL_CFG 0xB19 |
| * CORE_CSR_CDC_DELAY_CFG 0x3AC |
| * CORE_CDC_OFFSET_CFG 0x0 |
| * CORE_CDC_SLAVE_DDA_CFG 0x16334 |
| */ |
| |
| writel_relaxed(0x11800EC, host->ioaddr + CORE_CSR_CDC_CTLR_CFG0); |
| writel_relaxed(0x3011111, host->ioaddr + CORE_CSR_CDC_CTLR_CFG1); |
| writel_relaxed(0x1201000, host->ioaddr + CORE_CSR_CDC_CAL_TIMER_CFG0); |
| writel_relaxed(0x4, host->ioaddr + CORE_CSR_CDC_CAL_TIMER_CFG1); |
| writel_relaxed(0xCB732020, host->ioaddr + CORE_CSR_CDC_REFCOUNT_CFG); |
| writel_relaxed(0xB19, host->ioaddr + CORE_CSR_CDC_COARSE_CAL_CFG); |
| writel_relaxed(0x4E2, host->ioaddr + CORE_CSR_CDC_DELAY_CFG); |
| writel_relaxed(0x0, host->ioaddr + CORE_CDC_OFFSET_CFG); |
| writel_relaxed(0x16334, host->ioaddr + CORE_CDC_SLAVE_DDA_CFG); |
| |
| /* CDC HW Calibration */ |
| |
| /* Write 1 to SW_TRIG_FULL_CALIB field in CORE_CSR_CDC_CTLR_CFG0 */ |
| writel_relaxed((readl_relaxed(host->ioaddr + CORE_CSR_CDC_CTLR_CFG0) |
| | CORE_SW_TRIG_FULL_CALIB), |
| host->ioaddr + CORE_CSR_CDC_CTLR_CFG0); |
| |
| /* Write 0 to SW_TRIG_FULL_CALIB field in CORE_CSR_CDC_CTLR_CFG0 */ |
| writel_relaxed((readl_relaxed(host->ioaddr + CORE_CSR_CDC_CTLR_CFG0) |
| & ~CORE_SW_TRIG_FULL_CALIB), |
| host->ioaddr + CORE_CSR_CDC_CTLR_CFG0); |
| |
| /* Write 1 to HW_AUTOCAL_ENA field in CORE_CSR_CDC_CTLR_CFG0 */ |
| writel_relaxed((readl_relaxed(host->ioaddr + CORE_CSR_CDC_CTLR_CFG0) |
| | CORE_HW_AUTOCAL_ENA), |
| host->ioaddr + CORE_CSR_CDC_CTLR_CFG0); |
| |
| /* Write 1 to TIMER_ENA field in CORE_CSR_CDC_CAL_TIMER_CFG0 */ |
| writel_relaxed((readl_relaxed(host->ioaddr + |
| CORE_CSR_CDC_CAL_TIMER_CFG0) | CORE_TIMER_ENA), |
| host->ioaddr + CORE_CSR_CDC_CAL_TIMER_CFG0); |
| |
| mb(); |
| |
| /* Poll on CALIBRATION_DONE field in CORE_CSR_CDC_STATUS0 to be 1 */ |
| ret = readl_poll_timeout(host->ioaddr + CORE_CSR_CDC_STATUS0, |
| calib_done, (calib_done & CORE_CALIBRATION_DONE), 1, 50); |
| |
| if (ret == -ETIMEDOUT) { |
| pr_err("%s: %s: CDC Calibration was not completed\n", |
| mmc_hostname(host->mmc), __func__); |
| goto out; |
| } |
| |
| /* Verify CDC_ERROR_CODE field in CORE_CSR_CDC_STATUS0 is 0 */ |
| cdc_err = readl_relaxed(host->ioaddr + CORE_CSR_CDC_STATUS0) |
| & CORE_CDC_ERROR_CODE_MASK; |
| if (cdc_err) { |
| pr_err("%s: %s: CDC Error Code %d\n", |
| mmc_hostname(host->mmc), __func__, cdc_err); |
| ret = -EINVAL; |
| goto out; |
| } |
| |
| /* Write 1 to START_CDC_TRAFFIC field in CORE_DDR200_CFG */ |
| writel_relaxed((readl_relaxed(host->ioaddr + |
| msm_host_offset->CORE_DDR_200_CFG) |
| | CORE_START_CDC_TRAFFIC), |
| host->ioaddr + msm_host_offset->CORE_DDR_200_CFG); |
| out: |
| pr_debug("%s: Exit %s, ret:%d\n", mmc_hostname(host->mmc), |
| __func__, ret); |
| return ret; |
| } |
| |
| static int sdhci_msm_cm_dll_sdc4_calibration(struct sdhci_host *host) |
| { |
| struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); |
| struct sdhci_msm_host *msm_host = pltfm_host->priv; |
| const struct sdhci_msm_offset *msm_host_offset = |
| msm_host->offset; |
| u32 dll_status; |
| int ret = 0; |
| |
| pr_debug("%s: Enter %s\n", mmc_hostname(host->mmc), __func__); |
| |
| /* |
| * Reprogramming the value in case it might have been modified by |
| * bootloaders. |
| */ |
| if (msm_host->pdata->rclk_wa) { |
| writel_relaxed(msm_host->pdata->ddr_config, host->ioaddr + |
| msm_host_offset->CORE_DDR_CONFIG); |
| } else if (msm_host->dll_hsr && msm_host->dll_hsr->ddr_config) { |
| writel_relaxed(msm_host->dll_hsr->ddr_config, host->ioaddr + |
| msm_host_offset->CORE_DDR_CONFIG); |
| } else if (msm_host->rclk_delay_fix) { |
| writel_relaxed(DDR_CONFIG_POR_VAL, host->ioaddr + |
| msm_host_offset->CORE_DDR_CONFIG); |
| } else { |
| writel_relaxed(DDR_CONFIG_POR_VAL, host->ioaddr + |
| msm_host_offset->CORE_DDR_CONFIG_OLD); |
| } |
| |
| if (msm_host->enhanced_strobe && mmc_card_strobe(msm_host->mmc->card)) |
| writel_relaxed((readl_relaxed(host->ioaddr + |
| msm_host_offset->CORE_DDR_200_CFG) |
| | CORE_CMDIN_RCLK_EN), host->ioaddr + |
| msm_host_offset->CORE_DDR_200_CFG); |
| |
| /* Write 1 to DDR_CAL_EN field in CORE_DLL_CONFIG_2 */ |
| writel_relaxed((readl_relaxed(host->ioaddr + |
| msm_host_offset->CORE_DLL_CONFIG_2) |
| | CORE_DDR_CAL_EN), |
| host->ioaddr + msm_host_offset->CORE_DLL_CONFIG_2); |
| |
| /* Poll on DDR_DLL_LOCK bit in CORE_DLL_STATUS to be set */ |
| ret = readl_poll_timeout(host->ioaddr + |
| msm_host_offset->CORE_DLL_STATUS, |
| dll_status, (dll_status & CORE_DDR_DLL_LOCK), 10, 1000); |
| |
| if (ret == -ETIMEDOUT) { |
| pr_err("%s: %s: CM_DLL_SDC4 Calibration was not completed\n", |
| mmc_hostname(host->mmc), __func__); |
| goto out; |
| } |
| |
| /* |
| * set CORE_PWRSAVE_DLL bit in CORE_VENDOR_SPEC3. |
| * when MCLK is gated OFF, it is not gated for less than 0.5us |
| * and MCLK must be switched on for at-least 1us before DATA |
| * starts coming. Controllers with 14lpp tech DLL cannot |
| * guarantee above requirement. So PWRSAVE_DLL should not be |
| * turned on for host controllers using this DLL. |
| */ |
| if (!msm_host->use_14lpp_dll) |
| writel_relaxed((readl_relaxed(host->ioaddr + |
| msm_host_offset->CORE_VENDOR_SPEC3) |
| | CORE_PWRSAVE_DLL), host->ioaddr + |
| msm_host_offset->CORE_VENDOR_SPEC3); |
| mb(); |
| out: |
| pr_debug("%s: Exit %s, ret:%d\n", mmc_hostname(host->mmc), |
| __func__, ret); |
| return ret; |
| } |
| |
| static int sdhci_msm_enhanced_strobe(struct sdhci_host *host) |
| { |
| int ret = 0; |
| struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); |
| struct sdhci_msm_host *msm_host = pltfm_host->priv; |
| struct mmc_host *mmc = host->mmc; |
| |
| pr_debug("%s: Enter %s\n", mmc_hostname(host->mmc), __func__); |
| |
| if (!msm_host->enhanced_strobe || !mmc_card_strobe(mmc->card)) { |
| pr_debug("%s: host/card does not support hs400 enhanced strobe\n", |
| mmc_hostname(mmc)); |
| return -EINVAL; |
| } |
| |
| if (msm_host->calibration_done || |
| !(mmc->ios.timing == MMC_TIMING_MMC_HS400)) { |
| return 0; |
| } |
| |
| /* |
| * Reset the tuning block. |
| */ |
| ret = msm_init_cm_dll(host, DLL_INIT_NORMAL); |
| if (ret) |
| goto out; |
| |
| ret = sdhci_msm_cm_dll_sdc4_calibration(host); |
| out: |
| if (!ret) |
| msm_host->calibration_done = true; |
| pr_debug("%s: Exit %s, ret:%d\n", mmc_hostname(host->mmc), |
| __func__, ret); |
| return ret; |
| } |
| |
| static int sdhci_msm_hs400_dll_calibration(struct sdhci_host *host) |
| { |
| int ret = 0; |
| struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); |
| struct sdhci_msm_host *msm_host = pltfm_host->priv; |
| const struct sdhci_msm_offset *msm_host_offset = |
| msm_host->offset; |
| |
| pr_debug("%s: Enter %s\n", mmc_hostname(host->mmc), __func__); |
| |
| /* |
| * Retuning in HS400 (DDR mode) will fail, just reset the |
| * tuning block and restore the saved tuning phase. |
| */ |
| ret = msm_init_cm_dll(host, DLL_INIT_NORMAL); |
| if (ret) |
| goto out; |
| |
| /* Set the selected phase in delay line hw block */ |
| ret = msm_config_cm_dll_phase(host, msm_host->saved_tuning_phase); |
| if (ret) |
| goto out; |
| if (msm_host->dll_hsr->dll_config & CORE_CMD_DAT_TRACK_SEL) { |
| /* Write 1 to CMD_DAT_TRACK_SEL field in DLL_CONFIG */ |
| writel_relaxed((readl_relaxed(host->ioaddr + |
| msm_host_offset->CORE_DLL_CONFIG) |
| | CORE_CMD_DAT_TRACK_SEL), host->ioaddr + |
| msm_host_offset->CORE_DLL_CONFIG); |
| } |
| |
| if (msm_host->use_cdclp533) |
| /* Calibrate CDCLP533 DLL HW */ |
| ret = sdhci_msm_cdclp533_calibration(host); |
| else |
| /* Calibrate CM_DLL_SDC4 HW */ |
| ret = sdhci_msm_cm_dll_sdc4_calibration(host); |
| out: |
| pr_debug("%s: Exit %s, ret:%d\n", mmc_hostname(host->mmc), |
| __func__, ret); |
| return ret; |
| } |
| |
| static void sdhci_msm_set_mmc_drv_type(struct sdhci_host *host, u32 opcode, |
| u8 drv_type) |
| { |
| struct mmc_command cmd = {0}; |
| struct mmc_request mrq = {NULL}; |
| struct mmc_host *mmc = host->mmc; |
| u8 val = ((drv_type << 4) | 2); |
| |
| cmd.opcode = MMC_SWITCH; |
| cmd.arg = (MMC_SWITCH_MODE_WRITE_BYTE << 24) | |
| (EXT_CSD_HS_TIMING << 16) | |
| (val << 8) | |
| EXT_CSD_CMD_SET_NORMAL; |
| cmd.flags = MMC_CMD_AC | MMC_RSP_R1B; |
| /* 1 sec */ |
| cmd.busy_timeout = 1000 * 1000; |
| |
| memset(cmd.resp, 0, sizeof(cmd.resp)); |
| cmd.retries = 3; |
| |
| mrq.cmd = &cmd; |
| cmd.data = NULL; |
| |
| mmc_wait_for_req(mmc, &mrq); |
| pr_debug("%s: %s: set card drive type to %d\n", |
| mmc_hostname(mmc), __func__, |
| drv_type); |
| } |
| |
| int sdhci_msm_execute_tuning(struct sdhci_host *host, u32 opcode) |
| { |
| unsigned long flags; |
| int tuning_seq_cnt = 3; |
| u8 phase, *data_buf, tuned_phases[NUM_TUNING_PHASES], tuned_phase_cnt; |
| const u32 *tuning_block_pattern = tuning_block_64; |
| int size = sizeof(tuning_block_64); /* Tuning pattern size in bytes */ |
| int rc; |
| struct mmc_host *mmc = host->mmc; |
| struct mmc_ios ios = host->mmc->ios; |
| struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); |
| struct sdhci_msm_host *msm_host = pltfm_host->priv; |
| u8 drv_type = 0; |
| bool drv_type_changed = false; |
| struct mmc_card *card = host->mmc->card; |
| int sts_retry; |
| u8 last_good_phase = 0; |
| |
| /* |
| * Tuning is required for SDR104, HS200 and HS400 cards and |
| * if clock frequency is greater than 100MHz in these modes. |
| */ |
| if (host->clock <= CORE_FREQ_100MHZ || |
| !((ios.timing == MMC_TIMING_MMC_HS400) || |
| (ios.timing == MMC_TIMING_MMC_HS200) || |
| (ios.timing == MMC_TIMING_UHS_SDR104))) |
| return 0; |
| |
| /* |
| * Don't allow re-tuning for CRC errors observed for any commands |
| * that are sent during tuning sequence itself. |
| */ |
| if (msm_host->tuning_in_progress) |
| return 0; |
| msm_host->tuning_in_progress = true; |
| pr_debug("%s: Enter %s\n", mmc_hostname(mmc), __func__); |
| |
| /* CDC/SDC4 DLL HW calibration is only required for HS400 mode*/ |
| if (msm_host->tuning_done && !msm_host->calibration_done && |
| (mmc->ios.timing == MMC_TIMING_MMC_HS400)) { |
| rc = sdhci_msm_hs400_dll_calibration(host); |
| spin_lock_irqsave(&host->lock, flags); |
| if (!rc) |
| msm_host->calibration_done = true; |
| spin_unlock_irqrestore(&host->lock, flags); |
| goto out; |
| } |
| |
| spin_lock_irqsave(&host->lock, flags); |
| |
| if ((opcode == MMC_SEND_TUNING_BLOCK_HS200) && |
| (mmc->ios.bus_width == MMC_BUS_WIDTH_8)) { |
| tuning_block_pattern = tuning_block_128; |
| size = sizeof(tuning_block_128); |
| } |
| spin_unlock_irqrestore(&host->lock, flags); |
| |
| data_buf = kmalloc(size, GFP_KERNEL); |
| if (!data_buf) { |
| rc = -ENOMEM; |
| goto out; |
| } |
| |
| retry: |
| tuned_phase_cnt = 0; |
| |
| /* first of all reset the tuning block */ |
| rc = msm_init_cm_dll(host, DLL_INIT_NORMAL); |
| if (rc) |
| goto kfree; |
| |
| phase = 0; |
| do { |
| struct mmc_command cmd = {0}; |
| struct mmc_data data = {0}; |
| struct mmc_request mrq = { |
| .cmd = &cmd, |
| .data = &data |
| }; |
| struct scatterlist sg; |
| struct mmc_command sts_cmd = {0}; |
| |
| /* set the phase in delay line hw block */ |
| rc = msm_config_cm_dll_phase(host, phase); |
| if (rc) |
| goto kfree; |
| |
| cmd.opcode = opcode; |
| cmd.flags = MMC_RSP_R1 | MMC_CMD_ADTC; |
| |
| data.blksz = size; |
| data.blocks = 1; |
| data.flags = MMC_DATA_READ; |
| data.timeout_ns = 1000 * 1000 * 1000; /* 1 sec */ |
| |
| data.sg = &sg; |
| data.sg_len = 1; |
| sg_init_one(&sg, data_buf, size); |
| memset(data_buf, 0, size); |
| mmc_wait_for_req(mmc, &mrq); |
| |
| if (card && (cmd.error || data.error)) { |
| /* |
| * Set the dll to last known good phase while sending |
| * status command to ensure that status command won't |
| * fail due to bad phase. |
| */ |
| if (tuned_phase_cnt) |
| last_good_phase = |
| tuned_phases[tuned_phase_cnt-1]; |
| else if (msm_host->saved_tuning_phase != |
| INVALID_TUNING_PHASE) |
| last_good_phase = msm_host->saved_tuning_phase; |
| |
| rc = msm_config_cm_dll_phase(host, last_good_phase); |
| if (rc) |
| goto kfree; |
| |
| sts_cmd.opcode = MMC_SEND_STATUS; |
| sts_cmd.arg = card->rca << 16; |
| sts_cmd.flags = MMC_RSP_R1 | MMC_CMD_AC; |
| sts_retry = 5; |
| while (sts_retry) { |
| mmc_wait_for_cmd(mmc, &sts_cmd, 0); |
| |
| if (sts_cmd.error || |
| (R1_CURRENT_STATE(sts_cmd.resp[0]) |
| != R1_STATE_TRAN)) { |
| sts_retry--; |
| /* |
| * wait for at least 146 MCLK cycles for |
| * the card to move to TRANS state. As |
| * the MCLK would be min 200MHz for |
| * tuning, we need max 0.73us delay. To |
| * be on safer side 1ms delay is given. |
| */ |
| usleep_range(1000, 1200); |
| pr_debug("%s: phase %d sts cmd err %d resp 0x%x\n", |
| mmc_hostname(mmc), phase, |
| sts_cmd.error, sts_cmd.resp[0]); |
| continue; |
| } |
| break; |
| }; |
| } |
| |
| if (!cmd.error && !data.error && |
| !memcmp(data_buf, tuning_block_pattern, size)) { |
| /* tuning is successful at this tuning point */ |
| tuned_phases[tuned_phase_cnt++] = phase; |
| pr_debug("%s: %s: found *** good *** phase = %d\n", |
| mmc_hostname(mmc), __func__, phase); |
| } else { |
| /* Ignore crc errors occurred during tuning */ |
| if (cmd.error) |
| mmc->err_stats[MMC_ERR_CMD_CRC]--; |
| else if (data.error) |
| mmc->err_stats[MMC_ERR_DAT_CRC]--; |
| pr_debug("%s: %s: found ## bad ## phase = %d\n", |
| mmc_hostname(mmc), __func__, phase); |
| } |
| } while (++phase < 16); |
| |
| if ((tuned_phase_cnt == NUM_TUNING_PHASES) && |
| card && mmc_card_mmc(card)) { |
| /* |
| * If all phases pass then its a problem. So change the card's |
| * drive type to a different value, if supported and repeat |
| * tuning until at least one phase fails. Then set the original |
| * drive type back. |
| * |
| * If all the phases still pass after trying all possible |
| * drive types, then one of those 16 phases will be picked. |
| * This is no different from what was going on before the |
| * modification to change drive type and retune. |
| */ |
| pr_debug("%s: tuned phases count: %d\n", mmc_hostname(mmc), |
| tuned_phase_cnt); |
| |
| /* set drive type to other value . default setting is 0x0 */ |
| while (++drv_type <= MAX_DRV_TYPES_SUPPORTED_HS200) { |
| pr_debug("%s: trying different drive strength (%d)\n", |
| mmc_hostname(mmc), drv_type); |
| if (card->ext_csd.raw_driver_strength & |
| (1 << drv_type)) { |
| sdhci_msm_set_mmc_drv_type(host, opcode, |
| drv_type); |
| if (!drv_type_changed) |
| drv_type_changed = true; |
| goto retry; |
| } |
| } |
| } |
| |
| /* reset drive type to default (50 ohm) if changed */ |
| if (drv_type_changed) |
| sdhci_msm_set_mmc_drv_type(host, opcode, 0); |
| |
| if (tuned_phase_cnt) { |
| rc = msm_find_most_appropriate_phase(host, tuned_phases, |
| tuned_phase_cnt); |
| if (rc < 0) |
| goto kfree; |
| else |
| phase = (u8)rc; |
| |
| /* |
| * Finally set the selected phase in delay |
| * line hw block. |
| */ |
| rc = msm_config_cm_dll_phase(host, phase); |
| if (rc) |
| goto kfree; |
| msm_host->saved_tuning_phase = phase; |
| pr_debug("%s: %s: finally setting the tuning phase to %d\n", |
| mmc_hostname(mmc), __func__, phase); |
| } else { |
| if (--tuning_seq_cnt) |
| goto retry; |
| /* tuning failed */ |
| pr_err("%s: %s: no tuning point found\n", |
| mmc_hostname(mmc), __func__); |
| rc = -EIO; |
| } |
| |
| kfree: |
| kfree(data_buf); |
| out: |
| spin_lock_irqsave(&host->lock, flags); |
| if (!rc) |
| msm_host->tuning_done = true; |
| spin_unlock_irqrestore(&host->lock, flags); |
| msm_host->tuning_in_progress = false; |
| pr_debug("%s: Exit %s, err(%d)\n", mmc_hostname(mmc), __func__, rc); |
| return rc; |
| } |
| |
| static int sdhci_msm_setup_gpio(struct sdhci_msm_pltfm_data *pdata, bool enable) |
| { |
| struct sdhci_msm_gpio_data *curr; |
| int i, ret = 0; |
| |
| curr = pdata->pin_data->gpio_data; |
| for (i = 0; i < curr->size; i++) { |
| if (!gpio_is_valid(curr->gpio[i].no)) { |
| ret = -EINVAL; |
| pr_err("%s: Invalid gpio = %d\n", __func__, |
| curr->gpio[i].no); |
| goto free_gpios; |
| } |
| if (enable) { |
| ret = gpio_request(curr->gpio[i].no, |
| curr->gpio[i].name); |
| if (ret) { |
| pr_err("%s: gpio_request(%d, %s) failed %d\n", |
| __func__, curr->gpio[i].no, |
| curr->gpio[i].name, ret); |
| goto free_gpios; |
| } |
| curr->gpio[i].is_enabled = true; |
| } else { |
| gpio_free(curr->gpio[i].no); |
| curr->gpio[i].is_enabled = false; |
| } |
| } |
| return ret; |
| |
| free_gpios: |
| for (i--; i >= 0; i--) { |
| gpio_free(curr->gpio[i].no); |
| curr->gpio[i].is_enabled = false; |
| } |
| return ret; |
| } |
| |
| static int sdhci_msm_config_pinctrl_drv_type(struct sdhci_msm_pltfm_data *pdata, |
| unsigned int clock) |
| { |
| int ret = 0; |
| |
| if (clock > 150000000) { |
| if (pdata->pctrl_data->pins_drv_type_200MHz) |
| ret = pinctrl_select_state(pdata->pctrl_data->pctrl, |
| pdata->pctrl_data->pins_drv_type_200MHz); |
| } else if (clock > 75000000) { |
| if (pdata->pctrl_data->pins_drv_type_100MHz) |
| ret = pinctrl_select_state(pdata->pctrl_data->pctrl, |
| pdata->pctrl_data->pins_drv_type_100MHz); |
| } else if (clock > 400000) { |
| if (pdata->pctrl_data->pins_drv_type_50MHz) |
| ret = pinctrl_select_state(pdata->pctrl_data->pctrl, |
| pdata->pctrl_data->pins_drv_type_50MHz); |
| } else { |
| if (pdata->pctrl_data->pins_drv_type_400KHz) |
| ret = pinctrl_select_state(pdata->pctrl_data->pctrl, |
| pdata->pctrl_data->pins_drv_type_400KHz); |
| } |
| |
| return ret; |
| } |
| |
| static int sdhci_msm_setup_pinctrl(struct sdhci_msm_pltfm_data *pdata, |
| bool enable) |
| { |
| int ret = 0; |
| |
| if (enable) |
| ret = pinctrl_select_state(pdata->pctrl_data->pctrl, |
| pdata->pctrl_data->pins_active); |
| else |
| ret = pinctrl_select_state(pdata->pctrl_data->pctrl, |
| pdata->pctrl_data->pins_sleep); |
| |
| if (ret < 0) |
| pr_err("%s state for pinctrl failed with %d\n", |
| enable ? "Enabling" : "Disabling", ret); |
| |
| return ret; |
| } |
| |
| static int sdhci_msm_setup_pins(struct sdhci_msm_pltfm_data *pdata, bool enable) |
| { |
| int ret = 0; |
| |
| if (pdata->pin_cfg_sts == enable) { |
| return 0; |
| } else if (pdata->pctrl_data) { |
| ret = sdhci_msm_setup_pinctrl(pdata, enable); |
| goto out; |
| } else if (!pdata->pin_data) { |
| return 0; |
| } |
| |
| if (pdata->pin_data->is_gpio) |
| ret = sdhci_msm_setup_gpio(pdata, enable); |
| out: |
| if (!ret) |
| pdata->pin_cfg_sts = enable; |
| |
| return ret; |
| } |
| |
| static int sdhci_msm_dt_get_array(struct device *dev, const char *prop_name, |
| u32 **out, int *len, u32 size) |
| { |
| int ret = 0; |
| struct device_node *np = dev->of_node; |
| size_t sz; |
| u32 *arr = NULL; |
| |
| if (!of_get_property(np, prop_name, len)) { |
| ret = -EINVAL; |
| goto out; |
| } |
| sz = *len = *len / sizeof(*arr); |
| if (sz <= 0 || (size > 0 && (sz > size))) { |
| dev_err(dev, "%s invalid size\n", prop_name); |
| ret = -EINVAL; |
| goto out; |
| } |
| |
| arr = devm_kzalloc(dev, sz * sizeof(*arr), GFP_KERNEL); |
| if (!arr) { |
| dev_err(dev, "%s failed allocating memory\n", prop_name); |
| ret = -ENOMEM; |
| goto out; |
| } |
| |
| ret = of_property_read_u32_array(np, prop_name, arr, sz); |
| if (ret < 0) { |
| dev_err(dev, "%s failed reading array %d\n", prop_name, ret); |
| goto out; |
| } |
| *out = arr; |
| out: |
| if (ret) |
| *len = 0; |
| return ret; |
| } |
| |
| #define MAX_PROP_SIZE 32 |
| static int sdhci_msm_dt_parse_vreg_info(struct device *dev, |
| struct sdhci_msm_reg_data **vreg_data, const char *vreg_name) |
| { |
| int len, ret = 0; |
| const __be32 *prop; |
| char prop_name[MAX_PROP_SIZE]; |
| struct sdhci_msm_reg_data *vreg; |
| struct device_node *np = dev->of_node; |
| |
| snprintf(prop_name, MAX_PROP_SIZE, "%s-supply", vreg_name); |
| if (!of_parse_phandle(np, prop_name, 0)) { |
| dev_info(dev, "No vreg data found for %s\n", vreg_name); |
| return ret; |
| } |
| |
| vreg = devm_kzalloc(dev, sizeof(*vreg), GFP_KERNEL); |
| if (!vreg) { |
| dev_err(dev, "No memory for vreg: %s\n", vreg_name); |
| ret = -ENOMEM; |
| return ret; |
| } |
| |
| vreg->name = vreg_name; |
| |
| snprintf(prop_name, MAX_PROP_SIZE, |
| "qcom,%s-always-on", vreg_name); |
| if (of_get_property(np, prop_name, NULL)) |
| vreg->is_always_on = true; |
| |
| snprintf(prop_name, MAX_PROP_SIZE, |
| "qcom,%s-lpm-sup", vreg_name); |
| if (of_get_property(np, prop_name, NULL)) |
| vreg->lpm_sup = true; |
| |
| snprintf(prop_name, MAX_PROP_SIZE, |
| "qcom,%s-voltage-level", vreg_name); |
| prop = of_get_property(np, prop_name, &len); |
| if (!prop || (len != (2 * sizeof(__be32)))) { |
| dev_warn(dev, "%s %s property\n", |
| prop ? "invalid format" : "no", prop_name); |
| } else { |
| vreg->low_vol_level = be32_to_cpup(&prop[0]); |
| vreg->high_vol_level = be32_to_cpup(&prop[1]); |
| } |
| |
| snprintf(prop_name, MAX_PROP_SIZE, |
| "qcom,%s-current-level", vreg_name); |
| prop = of_get_property(np, prop_name, &len); |
| if (!prop || (len != (2 * sizeof(__be32)))) { |
| dev_warn(dev, "%s %s property\n", |
| prop ? "invalid format" : "no", prop_name); |
| } else { |
| vreg->lpm_uA = be32_to_cpup(&prop[0]); |
| vreg->hpm_uA = be32_to_cpup(&prop[1]); |
| } |
| |
| *vreg_data = vreg; |
| dev_dbg(dev, "%s: %s %s vol=[%d %d]uV, curr=[%d %d]uA\n", |
| vreg->name, vreg->is_always_on ? "always_on," : "", |
| vreg->lpm_sup ? "lpm_sup," : "", vreg->low_vol_level, |
| vreg->high_vol_level, vreg->lpm_uA, vreg->hpm_uA); |
| |
| return ret; |
| } |
| |
| static int sdhci_msm_parse_pinctrl_info(struct device *dev, |
| struct sdhci_msm_pltfm_data *pdata) |
| { |
| struct sdhci_pinctrl_data *pctrl_data; |
| struct pinctrl *pctrl; |
| int ret = 0; |
| |
| /* Try to obtain pinctrl handle */ |
| pctrl = devm_pinctrl_get(dev); |
| if (IS_ERR(pctrl)) { |
| ret = PTR_ERR(pctrl); |
| goto out; |
| } |
| pctrl_data = devm_kzalloc(dev, sizeof(*pctrl_data), GFP_KERNEL); |
| if (!pctrl_data) { |
| dev_err(dev, "No memory for sdhci_pinctrl_data\n"); |
| ret = -ENOMEM; |
| goto out; |
| } |
| pctrl_data->pctrl = pctrl; |
| /* Look-up and keep the states handy to be used later */ |
| pctrl_data->pins_active = pinctrl_lookup_state( |
| pctrl_data->pctrl, "active"); |
| if (IS_ERR(pctrl_data->pins_active)) { |
| ret = PTR_ERR(pctrl_data->pins_active); |
| dev_err(dev, "Could not get active pinstates, err:%d\n", ret); |
| goto out; |
| } |
| pctrl_data->pins_sleep = pinctrl_lookup_state( |
| pctrl_data->pctrl, "sleep"); |
| if (IS_ERR(pctrl_data->pins_sleep)) { |
| ret = PTR_ERR(pctrl_data->pins_sleep); |
| dev_err(dev, "Could not get sleep pinstates, err:%d\n", ret); |
| goto out; |
| } |
| |
| pctrl_data->pins_drv_type_400KHz = pinctrl_lookup_state( |
| pctrl_data->pctrl, "ds_400KHz"); |
| if (IS_ERR(pctrl_data->pins_drv_type_400KHz)) { |
| dev_dbg(dev, "Could not get 400K pinstates, err:%d\n", ret); |
| pctrl_data->pins_drv_type_400KHz = NULL; |
| } |
| |
| pctrl_data->pins_drv_type_50MHz = pinctrl_lookup_state( |
| pctrl_data->pctrl, "ds_50MHz"); |
| if (IS_ERR(pctrl_data->pins_drv_type_50MHz)) { |
| dev_dbg(dev, "Could not get 50M pinstates, err:%d\n", ret); |
| pctrl_data->pins_drv_type_50MHz = NULL; |
| } |
| |
| pctrl_data->pins_drv_type_100MHz = pinctrl_lookup_state( |
| pctrl_data->pctrl, "ds_100MHz"); |
| if (IS_ERR(pctrl_data->pins_drv_type_100MHz)) { |
| dev_dbg(dev, "Could not get 100M pinstates, err:%d\n", ret); |
| pctrl_data->pins_drv_type_100MHz = NULL; |
| } |
| |
| pctrl_data->pins_drv_type_200MHz = pinctrl_lookup_state( |
| pctrl_data->pctrl, "ds_200MHz"); |
| if (IS_ERR(pctrl_data->pins_drv_type_200MHz)) { |
| dev_dbg(dev, "Could not get 200M pinstates, err:%d\n", ret); |
| pctrl_data->pins_drv_type_200MHz = NULL; |
| } |
| |
| pdata->pctrl_data = pctrl_data; |
| out: |
| return ret; |
| } |
| |
| #define GPIO_NAME_MAX_LEN 32 |
| static int sdhci_msm_dt_parse_gpio_info(struct device *dev, |
| struct sdhci_msm_pltfm_data *pdata) |
| { |
| int ret = 0, cnt, i; |
| struct sdhci_msm_pin_data *pin_data; |
| struct device_node *np = dev->of_node; |
| |
| ret = sdhci_msm_parse_pinctrl_info(dev, pdata); |
| if (!ret) { |
| goto out; |
| } else if (ret == -EPROBE_DEFER) { |
| dev_err(dev, "Pinctrl framework not registered, err:%d\n", ret); |
| goto out; |
| } else { |
| dev_err(dev, "Parsing Pinctrl failed with %d, falling back on GPIO lib\n", |
| ret); |
| ret = 0; |
| } |
| pin_data = devm_kzalloc(dev, sizeof(*pin_data), GFP_KERNEL); |
| if (!pin_data) { |
| dev_err(dev, "No memory for pin_data\n"); |
| ret = -ENOMEM; |
| goto out; |
| } |
| |
| cnt = of_gpio_count(np); |
| if (cnt > 0) { |
| pin_data->gpio_data = devm_kzalloc(dev, |
| sizeof(struct sdhci_msm_gpio_data), GFP_KERNEL); |
| if (!pin_data->gpio_data) { |
| dev_err(dev, "No memory for gpio_data\n"); |
| ret = -ENOMEM; |
| goto out; |
| } |
| pin_data->gpio_data->size = cnt; |
| pin_data->gpio_data->gpio = devm_kzalloc(dev, cnt * |
| sizeof(struct sdhci_msm_gpio), GFP_KERNEL); |
| |
| if (!pin_data->gpio_data->gpio) { |
| dev_err(dev, "No memory for gpio\n"); |
| ret = -ENOMEM; |
| goto out; |
| } |
| |
| for (i = 0; i < cnt; i++) { |
| const char *name = NULL; |
| char result[GPIO_NAME_MAX_LEN]; |
| pin_data->gpio_data->gpio[i].no = of_get_gpio(np, i); |
| of_property_read_string_index(np, |
| "qcom,gpio-names", i, &name); |
| |
| snprintf(result, GPIO_NAME_MAX_LEN, "%s-%s", |
| dev_name(dev), name ? name : "?"); |
| pin_data->gpio_data->gpio[i].name = result; |
| dev_dbg(dev, "%s: gpio[%s] = %d\n", __func__, |
| pin_data->gpio_data->gpio[i].name, |
| pin_data->gpio_data->gpio[i].no); |
| } |
| } |
| pdata->pin_data = pin_data; |
| out: |
| if (ret) |
| dev_err(dev, "%s failed with err %d\n", __func__, ret); |
| return ret; |
| } |
| |
| #ifdef CONFIG_SMP |
| static inline void parse_affine_irq(struct sdhci_msm_pltfm_data *pdata) |
| { |
| pdata->pm_qos_data.irq_req_type = PM_QOS_REQ_AFFINE_IRQ; |
| } |
| #else |
| static inline void parse_affine_irq(struct sdhci_msm_pltfm_data *pdata) { } |
| #endif |
| |
| static int sdhci_msm_pm_qos_parse_irq(struct device *dev, |
| struct sdhci_msm_pltfm_data *pdata) |
| { |
| struct device_node *np = dev->of_node; |
| const char *str; |
| u32 cpu; |
| int ret = 0; |
| int i; |
| |
| pdata->pm_qos_data.irq_valid = false; |
| pdata->pm_qos_data.irq_req_type = PM_QOS_REQ_AFFINE_CORES; |
| if (!of_property_read_string(np, "qcom,pm-qos-irq-type", &str) && |
| !strcmp(str, "affine_irq")) { |
| parse_affine_irq(pdata); |
| } |
| |
| /* must specify cpu for "affine_cores" type */ |
| if (pdata->pm_qos_data.irq_req_type == PM_QOS_REQ_AFFINE_CORES) { |
| pdata->pm_qos_data.irq_cpu = -1; |
| ret = of_property_read_u32(np, "qcom,pm-qos-irq-cpu", &cpu); |
| if (ret) { |
| dev_err(dev, "%s: error %d reading irq cpu\n", __func__, |
| ret); |
| goto out; |
| } |
| if (cpu < 0 || cpu >= num_possible_cpus()) { |
| dev_err(dev, "%s: invalid irq cpu %d (NR_CPUS=%d)\n", |
| __func__, cpu, num_possible_cpus()); |
| ret = -EINVAL; |
| goto out; |
| } |
| pdata->pm_qos_data.irq_cpu = cpu; |
| } |
| |
| if (of_property_count_u32_elems(np, "qcom,pm-qos-irq-latency") != |
| SDHCI_POWER_POLICY_NUM) { |
| dev_err(dev, "%s: could not read %d values for 'qcom,pm-qos-irq-latency'\n", |
| __func__, SDHCI_POWER_POLICY_NUM); |
| ret = -EINVAL; |
| goto out; |
| } |
| |
| for (i = 0; i < SDHCI_POWER_POLICY_NUM; i++) |
| of_property_read_u32_index(np, "qcom,pm-qos-irq-latency", i, |
| &pdata->pm_qos_data.irq_latency.latency[i]); |
| |
| pdata->pm_qos_data.irq_valid = true; |
| out: |
| return ret; |
| } |
| |
| static int sdhci_msm_pm_qos_parse_cpu_groups(struct device *dev, |
| struct sdhci_msm_pltfm_data *pdata) |
| { |
| struct device_node *np = dev->of_node; |
| u32 mask; |
| int nr_groups; |
| int ret; |
| int i; |
| |
| /* Read cpu group mapping */ |
| nr_groups = of_property_count_u32_elems(np, "qcom,pm-qos-cpu-groups"); |
| if (nr_groups <= 0) { |
| ret = -EINVAL; |
| goto out; |
| } |
| pdata->pm_qos_data.cpu_group_map.nr_groups = nr_groups; |
| pdata->pm_qos_data.cpu_group_map.mask = |
| kcalloc(nr_groups, sizeof(cpumask_t), GFP_KERNEL); |
| if (!pdata->pm_qos_data.cpu_group_map.mask) { |
| ret = -ENOMEM; |
| goto out; |
| } |
| |
| for (i = 0; i < nr_groups; i++) { |
| of_property_read_u32_index(np, "qcom,pm-qos-cpu-groups", |
| i, &mask); |
| |
| pdata->pm_qos_data.cpu_group_map.mask[i].bits[0] = mask; |
| if (!cpumask_subset(&pdata->pm_qos_data.cpu_group_map.mask[i], |
| cpu_possible_mask)) { |
| dev_err(dev, "%s: invalid mask 0x%x of cpu group #%d\n", |
| __func__, mask, i); |
| ret = -EINVAL; |
| goto free_res; |
| } |
| } |
| return 0; |
| |
| free_res: |
| kfree(pdata->pm_qos_data.cpu_group_map.mask); |
| out: |
| return ret; |
| } |
| |
| static int sdhci_msm_pm_qos_parse_latency(struct device *dev, const char *name, |
| int nr_groups, struct sdhci_msm_pm_qos_latency **latency) |
| { |
| struct device_node *np = dev->of_node; |
| struct sdhci_msm_pm_qos_latency *values; |
| int ret; |
| int i; |
| int group; |
| int cfg; |
| |
| ret = of_property_count_u32_elems(np, name); |
| if (ret > 0 && ret != SDHCI_POWER_POLICY_NUM * nr_groups) { |
| dev_err(dev, "%s: invalid number of values for property %s: expected=%d actual=%d\n", |
| __func__, name, SDHCI_POWER_POLICY_NUM * nr_groups, |
| ret); |
| return -EINVAL; |
| } else if (ret < 0) { |
| return ret; |
| } |
| |
| values = kcalloc(nr_groups, sizeof(struct sdhci_msm_pm_qos_latency), |
| GFP_KERNEL); |
| if (!values) |
| return -ENOMEM; |
| |
| for (i = 0; i < SDHCI_POWER_POLICY_NUM * nr_groups; i++) { |
| group = i / SDHCI_POWER_POLICY_NUM; |
| cfg = i % SDHCI_POWER_POLICY_NUM; |
| of_property_read_u32_index(np, name, i, |
| &(values[group].latency[cfg])); |
| } |
| |
| *latency = values; |
| return 0; |
| } |
| |
| static void sdhci_msm_pm_qos_parse(struct device *dev, |
| struct sdhci_msm_pltfm_data *pdata) |
| { |
| if (sdhci_msm_pm_qos_parse_irq(dev, pdata)) |
| dev_notice(dev, "%s: PM QoS voting for IRQ will be disabled\n", |
| __func__); |
| |
| if (!sdhci_msm_pm_qos_parse_cpu_groups(dev, pdata)) { |
| pdata->pm_qos_data.cmdq_valid = |
| !sdhci_msm_pm_qos_parse_latency(dev, |
| "qcom,pm-qos-cmdq-latency-us", |
| pdata->pm_qos_data.cpu_group_map.nr_groups, |
| &pdata->pm_qos_data.cmdq_latency); |
| pdata->pm_qos_data.legacy_valid = |
| !sdhci_msm_pm_qos_parse_latency(dev, |
| "qcom,pm-qos-legacy-latency-us", |
| pdata->pm_qos_data.cpu_group_map.nr_groups, |
| &pdata->pm_qos_data.latency); |
| if (!pdata->pm_qos_data.cmdq_valid && |
| !pdata->pm_qos_data.legacy_valid) { |
| /* clean-up previously allocated arrays */ |
| kfree(pdata->pm_qos_data.latency); |
| kfree(pdata->pm_qos_data.cmdq_latency); |
| dev_err(dev, "%s: invalid PM QoS latency values. Voting for cpu group will be disabled\n", |
| __func__); |
| } |
| } else { |
| dev_notice(dev, "%s: PM QoS voting for cpu group will be disabled\n", |
| __func__); |
| } |
| } |
| |
| #ifdef CONFIG_NVMEM |
| /* Parse qfprom data for deciding on errata work-arounds */ |
| static long qfprom_read(struct device *dev, const char *name) |
| { |
| struct nvmem_cell *cell; |
| ssize_t len = 0; |
| u32 *buf, val = 0; |
| long err = 0; |
| |
| cell = nvmem_cell_get(dev, name); |
| if (IS_ERR(cell)) { |
| err = PTR_ERR(cell); |
| dev_err(dev, "failed opening nvmem cell err : %ld\n", err); |
| /* If entry does not exist, then that is not an error */ |
| if (err == -ENOENT) |
| err = 0; |
| return err; |
| } |
| |
| buf = (u32 *)nvmem_cell_read(cell, &len); |
| if (IS_ERR(buf) || !len) { |
| dev_err(dev, "Failed reading nvmem cell, err: %u, bytes fetched: %zd\n", |
| *buf, len); |
| if (!IS_ERR(buf)) { |
| kfree(buf); |
| err = -EINVAL; |
| } else { |
| err = PTR_ERR(buf); |
| } |
| } else { |
| /* |
| * 30 bits from bit offset 0 would be read. |
| * We're interested in bits 28:29 |
| */ |
| val = (*buf >> 28) & 0x3; |
| kfree(buf); |
| } |
| |
| nvmem_cell_put(cell); |
| return err ? err : (long) val; |
| } |
| |
| /* Reads the SoC version */ |
| static int sdhci_msm_get_socrev(struct device *dev, |
| struct sdhci_msm_host *msm_host) |
| { |
| |
| msm_host->soc_min_rev = qfprom_read(dev, "minor_rev"); |
| |
| if (msm_host->soc_min_rev < 0) |
| dev_err(dev, "failed getting soc_min_rev, err : %d\n", |
| msm_host->soc_min_rev); |
| return msm_host->soc_min_rev; |
| } |
| #else |
| /* Reads the SoC version */ |
| static int sdhci_msm_get_socrev(struct device *dev, |
| struct sdhci_msm_host *msm_host) |
| { |
| return 0; |
| } |
| #endif |
| |
| static int sdhci_msm_dt_parse_hsr_info(struct device *dev, |
| struct sdhci_msm_host *msm_host) |
| |
| { |
| u32 *dll_hsr_table = NULL; |
| int dll_hsr_table_len, dll_hsr_reg_count; |
| int ret = 0; |
| |
| if (sdhci_msm_dt_get_array(dev, "qcom,dll-hsr-list", |
| &dll_hsr_table, &dll_hsr_table_len, 0)) |
| goto skip_hsr; |
| |
| dll_hsr_reg_count = sizeof(struct sdhci_msm_dll_hsr) / sizeof(u32); |
| if (dll_hsr_table_len != dll_hsr_reg_count) { |
| dev_err(dev, "Number of HSR entries are not matching\n"); |
| ret = -EINVAL; |
| } else { |
| msm_host->dll_hsr = (struct sdhci_msm_dll_hsr *)dll_hsr_table; |
| } |
| |
| skip_hsr: |
| if (!msm_host->dll_hsr) |
| dev_info(dev, "Failed to get dll hsr settings from dt\n"); |
| return ret; |
| } |
| |
| /* Parse platform data */ |
| static |
| struct sdhci_msm_pltfm_data *sdhci_msm_populate_pdata(struct device *dev, |
| struct sdhci_msm_host *msm_host) |
| { |
| struct sdhci_msm_pltfm_data *pdata = NULL; |
| struct device_node *np = dev->of_node; |
| u32 bus_width = 0; |
| int len, i; |
| int clk_table_len; |
| u32 *clk_table = NULL; |
| int ice_clk_table_len; |
| u32 *ice_clk_table = NULL; |
| enum of_gpio_flags flags = OF_GPIO_ACTIVE_LOW; |
| const char *lower_bus_speed = NULL; |
| int bus_clk_table_len; |
| u32 *bus_clk_table = NULL; |
| |
| pdata = devm_kzalloc(dev, sizeof(*pdata), GFP_KERNEL); |
| if (!pdata) { |
| dev_err(dev, "failed to allocate memory for platform data\n"); |
| goto out; |
| } |
| |
| pdata->status_gpio = of_get_named_gpio_flags(np, "cd-gpios", 0, &flags); |
| if (gpio_is_valid(pdata->status_gpio) && !(flags & OF_GPIO_ACTIVE_LOW)) |
| pdata->caps2 |= MMC_CAP2_CD_ACTIVE_HIGH; |
| |
| of_property_read_u32(np, "qcom,bus-width", &bus_width); |
| if (bus_width == 8) |
| pdata->mmc_bus_width = MMC_CAP_8_BIT_DATA; |
| else if (bus_width == 4) |
| pdata->mmc_bus_width = MMC_CAP_4_BIT_DATA; |
| else { |
| dev_notice(dev, "invalid bus-width, default to 1-bit mode\n"); |
| pdata->mmc_bus_width = 0; |
| } |
| |
| if (sdhci_msm_dt_get_array(dev, "qcom,devfreq,freq-table", |
| &msm_host->mmc->clk_scaling.pltfm_freq_table, |
| &msm_host->mmc->clk_scaling.pltfm_freq_table_sz, 0)) |
| pr_debug("%s: no clock scaling frequencies were supplied\n", |
| dev_name(dev)); |
| else if (!msm_host->mmc->clk_scaling.pltfm_freq_table || |
| !msm_host->mmc->clk_scaling.pltfm_freq_table_sz) |
| dev_err(dev, "bad dts clock scaling frequencies\n"); |
| |
| /* |
| * Few hosts can support DDR52 mode at the same lower |
| * system voltage corner as high-speed mode. In such cases, |
| * it is always better to put it in DDR mode which will |
| * improve the performance without any power impact. |
| */ |
| if (!of_property_read_string(np, "qcom,scaling-lower-bus-speed-mode", |
| &lower_bus_speed)) { |
| if (!strcmp(lower_bus_speed, "DDR52")) |
| msm_host->mmc->clk_scaling.lower_bus_speed_mode |= |
| MMC_SCALING_LOWER_DDR52_MODE; |
| } |
| |
| if (sdhci_msm_dt_get_array(dev, "qcom,clk-rates", |
| &clk_table, &clk_table_len, 0)) { |
| dev_err(dev, "failed parsing supported clock rates\n"); |
| goto out; |
| } |
| if (!clk_table || !clk_table_len) { |
| dev_err(dev, "Invalid clock table\n"); |
| goto out; |
| } |
| pdata->sup_clk_table = clk_table; |
| pdata->sup_clk_cnt = clk_table_len; |
| |
| if (!sdhci_msm_dt_get_array(dev, "qcom,bus-aggr-clk-rates", |
| &bus_clk_table, &bus_clk_table_len, 0)) { |
| if (bus_clk_table && bus_clk_table_len) { |
| pdata->bus_clk_table = bus_clk_table; |
| pdata->bus_clk_cnt = bus_clk_table_len; |
| } |
| } |
| |
| if (msm_host->ice.pdev) { |
| if (sdhci_msm_dt_get_array(dev, "qcom,ice-clk-rates", |
| &ice_clk_table, &ice_clk_table_len, 0)) { |
| dev_err(dev, "failed parsing supported ice clock rates\n"); |
| goto out; |
| } |
| if (!ice_clk_table || !ice_clk_table_len) { |
| dev_err(dev, "Invalid clock table\n"); |
| goto out; |
| } |
| if (ice_clk_table_len != 2) { |
| dev_err(dev, "Need max and min frequencies in the table\n"); |
| goto out; |
| } |
| pdata->sup_ice_clk_table = ice_clk_table; |
| pdata->sup_ice_clk_cnt = ice_clk_table_len; |
| pdata->ice_clk_max = pdata->sup_ice_clk_table[0]; |
| pdata->ice_clk_min = pdata->sup_ice_clk_table[1]; |
| dev_dbg(dev, "supported ICE clock rates (Hz): max: %u min: %u\n", |
| pdata->ice_clk_max, pdata->ice_clk_min); |
| } |
| |
| pdata->vreg_data = devm_kzalloc(dev, sizeof(struct |
| sdhci_msm_slot_reg_data), |
| GFP_KERNEL); |
| if (!pdata->vreg_data) { |
| dev_err(dev, "failed to allocate memory for vreg data\n"); |
| goto out; |
| } |
| |
| if (sdhci_msm_dt_parse_vreg_info(dev, &pdata->vreg_data->vdd_data, |
| "vdd")) { |
| dev_err(dev, "failed parsing vdd data\n"); |
| goto out; |
| } |
| if (sdhci_msm_dt_parse_vreg_info(dev, |
| &pdata->vreg_data->vdd_io_data, |
| "vdd-io")) { |
| dev_err(dev, "failed parsing vdd-io data\n"); |
| goto out; |
| } |
| |
| if (sdhci_msm_dt_parse_gpio_info(dev, pdata)) { |
| dev_err(dev, "failed parsing gpio data\n"); |
| goto out; |
| } |
| |
| len = of_property_count_strings(np, "qcom,bus-speed-mode"); |
| |
| for (i = 0; i < len; i++) { |
| const char *name = NULL; |
| |
| of_property_read_string_index(np, |
| "qcom,bus-speed-mode", i, &name); |
| if (!name) |
| continue; |
| |
| if (!strncmp(name, "HS400_1p8v", sizeof("HS400_1p8v"))) |
| pdata->caps2 |= MMC_CAP2_HS400_1_8V; |
| else if (!strncmp(name, "HS400_1p2v", sizeof("HS400_1p2v"))) |
| pdata->caps2 |= MMC_CAP2_HS400_1_2V; |
| else if (!strncmp(name, "HS200_1p8v", sizeof("HS200_1p8v"))) |
| pdata->caps2 |= MMC_CAP2_HS200_1_8V_SDR; |
| else if (!strncmp(name, "HS200_1p2v", sizeof("HS200_1p2v"))) |
| pdata->caps2 |= MMC_CAP2_HS200_1_2V_SDR; |
| else if (!strncmp(name, "DDR_1p8v", sizeof("DDR_1p8v"))) |
| pdata->caps |= MMC_CAP_1_8V_DDR |
| | MMC_CAP_UHS_DDR50; |
| else if (!strncmp(name, "DDR_1p2v", sizeof("DDR_1p2v"))) |
| pdata->caps |= MMC_CAP_1_2V_DDR |
| | MMC_CAP_UHS_DDR50; |
| } |
| |
| if (of_get_property(np, "qcom,nonremovable", NULL)) |
| pdata->nonremovable = true; |
| |
| if (of_get_property(np, "qcom,nonhotplug", NULL)) |
| pdata->nonhotplug = true; |
| |
| pdata->largeaddressbus = |
| of_property_read_bool(np, "qcom,large-address-bus"); |
| |
| if (of_property_read_bool(np, "qcom,wakeup-on-idle")) |
| msm_host->mmc->wakeup_on_idle = true; |
| |
| sdhci_msm_pm_qos_parse(dev, pdata); |
| |
| if (of_get_property(np, "qcom,core_3_0v_support", NULL)) |
| msm_host->core_3_0v_support = true; |
| |
| pdata->sdr104_wa = of_property_read_bool(np, "qcom,sdr104-wa"); |
| msm_host->regs_restore.is_supported = |
| of_property_read_bool(np, "qcom,restore-after-cx-collapse"); |
| |
| if (!of_property_read_u32(np, "qcom,ddr-config", &pdata->ddr_config)) |
| pdata->rclk_wa = true; |
| |
| if (sdhci_msm_dt_parse_hsr_info(dev, msm_host)) |
| goto out; |
| |
| /* |
| * rclk_wa is not required if soc version is mentioned and |
| * is not base version. |
| */ |
| if (msm_host->soc_min_rev != 0) |
| pdata->rclk_wa = false; |
| |
| return pdata; |
| out: |
| return NULL; |
| } |
| |
| /* Returns required bandwidth in Bytes per Sec */ |
| static unsigned int sdhci_get_bw_required(struct sdhci_host *host, |
| struct mmc_ios *ios) |
| { |
| struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); |
| struct sdhci_msm_host *msm_host = pltfm_host->priv; |
| |
| unsigned int bw; |
| |
| bw = msm_host->clk_rate; |
| /* |
| * For DDR mode, SDCC controller clock will be at |
| * the double rate than the actual clock that goes to card. |
| */ |
| if (ios->bus_width == MMC_BUS_WIDTH_4) |
| bw /= 2; |
| else if (ios->bus_width == MMC_BUS_WIDTH_1) |
| bw /= 8; |
| |
| return bw; |
| } |
| |
| static int sdhci_msm_bus_get_vote_for_bw(struct sdhci_msm_host *host, |
| unsigned int bw) |
| { |
| unsigned int *table = host->pdata->voting_data->bw_vecs; |
| unsigned int size = host->pdata->voting_data->bw_vecs_size; |
| int i; |
| |
| if (host->msm_bus_vote.is_max_bw_needed && bw) |
| return host->msm_bus_vote.max_bw_vote; |
| |
| for (i = 0; i < size; i++) { |
| if (bw <= table[i]) |
| break; |
| } |
| |
| if (i && (i == size)) |
| i--; |
| |
| return i; |
| } |
| |
| /* |
| * This function must be called with host lock acquired. |
| * Caller of this function should also ensure that msm bus client |
| * handle is not null. |
| */ |
| static inline int sdhci_msm_bus_set_vote(struct sdhci_msm_host *msm_host, |
| int vote, |
| unsigned long *flags) |
| { |
| struct sdhci_host *host = platform_get_drvdata(msm_host->pdev); |
| int rc = 0; |
| |
| BUG_ON(!flags); |
| |
| if (vote != msm_host->msm_bus_vote.curr_vote) { |
| spin_unlock_irqrestore(&host->lock, *flags); |
| rc = msm_bus_scale_client_update_request( |
| msm_host->msm_bus_vote.client_handle, vote); |
| spin_lock_irqsave(&host->lock, *flags); |
| if (rc) { |
| pr_err("%s: msm_bus_scale_client_update_request() failed: bus_client_handle=0x%x, vote=%d, err=%d\n", |
| mmc_hostname(host->mmc), |
| msm_host->msm_bus_vote.client_handle, vote, rc); |
| goto out; |
| } |
| msm_host->msm_bus_vote.curr_vote = vote; |
| } |
| out: |
| return rc; |
| } |
| |
| /* |
| * Internal work. Work to set 0 bandwidth for msm bus. |
| */ |
| static void sdhci_msm_bus_work(struct work_struct *work) |
| { |
| struct sdhci_msm_host *msm_host; |
| struct sdhci_host *host; |
| unsigned long flags; |
| |
| msm_host = container_of(work, struct sdhci_msm_host, |
| msm_bus_vote.vote_work.work); |
| host = platform_get_drvdata(msm_host->pdev); |
| |
| if (!msm_host->msm_bus_vote.client_handle) |
| return; |
| |
| spin_lock_irqsave(&host->lock, flags); |
| /* don't vote for 0 bandwidth if any request is in progress */ |
| if (!host->mrq) { |
| sdhci_msm_bus_set_vote(msm_host, |
| msm_host->msm_bus_vote.min_bw_vote, &flags); |
| } else |
| pr_warning("%s: %s: Transfer in progress. skipping bus voting to 0 bandwidth\n", |
| mmc_hostname(host->mmc), __func__); |
| spin_unlock_irqrestore(&host->lock, flags); |
| } |
| |
| /* |
| * This function cancels any scheduled delayed work and sets the bus |
| * vote based on bw (bandwidth) argument. |
| */ |
| static void sdhci_msm_bus_cancel_work_and_set_vote(struct sdhci_host *host, |
| unsigned int bw) |
| { |
| int vote; |
| unsigned long flags; |
| struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); |
| struct sdhci_msm_host *msm_host = pltfm_host->priv; |
| |
| cancel_delayed_work_sync(&msm_host->msm_bus_vote.vote_work); |
| spin_lock_irqsave(&host->lock, flags); |
| vote = sdhci_msm_bus_get_vote_for_bw(msm_host, bw); |
| sdhci_msm_bus_set_vote(msm_host, vote, &flags); |
| spin_unlock_irqrestore(&host->lock, flags); |
| } |
| |
| #define MSM_MMC_BUS_VOTING_DELAY 200 /* msecs */ |
| |
| /* This function queues a work which will set the bandwidth requiement to 0 */ |
| static void sdhci_msm_bus_queue_work(struct sdhci_host *host) |
| { |
| unsigned long flags; |
| struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); |
| struct sdhci_msm_host *msm_host = pltfm_host->priv; |
| |
| spin_lock_irqsave(&host->lock, flags); |
| if (msm_host->msm_bus_vote.min_bw_vote != |
| msm_host->msm_bus_vote.curr_vote) |
| queue_delayed_work(system_wq, |
| &msm_host->msm_bus_vote.vote_work, |
| msecs_to_jiffies(MSM_MMC_BUS_VOTING_DELAY)); |
| spin_unlock_irqrestore(&host->lock, flags); |
| } |
| |
| static int sdhci_msm_bus_register(struct sdhci_msm_host *host, |
| struct platform_device *pdev) |
| { |
| int rc = 0; |
| struct msm_bus_scale_pdata *bus_pdata; |
| |
| struct sdhci_msm_bus_voting_data *data; |
| struct device *dev = &pdev->dev; |
| |
| data = devm_kzalloc(dev, |
| sizeof(struct sdhci_msm_bus_voting_data), GFP_KERNEL); |
| if (!data) { |
| dev_err(&pdev->dev, |
| "%s: failed to allocate memory\n", __func__); |
| rc = -ENOMEM; |
| goto out; |
| } |
| data->bus_pdata = msm_bus_cl_get_pdata(pdev); |
| if (data->bus_pdata) { |
| rc = sdhci_msm_dt_get_array(dev, "qcom,bus-bw-vectors-bps", |
| &data->bw_vecs, &data->bw_vecs_size, 0); |
| if (rc) { |
| dev_err(&pdev->dev, |
| "%s: Failed to get bus-bw-vectors-bps\n", |
| __func__); |
| goto out; |
| } |
| host->pdata->voting_data = data; |
| } |
| if (host->pdata->voting_data && |
| host->pdata->voting_data->bus_pdata && |
| host->pdata->voting_data->bw_vecs && |
| host->pdata->voting_data->bw_vecs_size) { |
| |
| bus_pdata = host->pdata->voting_data->bus_pdata; |
| host->msm_bus_vote.client_handle = |
| msm_bus_scale_register_client(bus_pdata); |
| if (!host->msm_bus_vote.client_handle) { |
| dev_err(&pdev->dev, "msm_bus_scale_register_client()\n"); |
| rc = -EFAULT; |
| goto out; |
| } |
| /* cache the vote index for minimum and maximum bandwidth */ |
| host->msm_bus_vote.min_bw_vote = |
| sdhci_msm_bus_get_vote_for_bw(host, 0); |
| host->msm_bus_vote.max_bw_vote = |
| sdhci_msm_bus_get_vote_for_bw(host, UINT_MAX); |
| } else { |
| devm_kfree(dev, data); |
| } |
| |
| out: |
| return rc; |
| } |
| |
| static void sdhci_msm_bus_unregister(struct sdhci_msm_host *host) |
| { |
| if (host->msm_bus_vote.client_handle) |
| msm_bus_scale_unregister_client( |
| host->msm_bus_vote.client_handle); |
| } |
| |
| static void sdhci_msm_bus_voting(struct sdhci_host *host, u32 enable) |
| { |
| struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); |
| struct sdhci_msm_host *msm_host = pltfm_host->priv; |
| struct mmc_ios *ios = &host->mmc->ios; |
| unsigned int bw; |
| |
| if (!msm_host->msm_bus_vote.client_handle) |
| return; |
| |
| bw = sdhci_get_bw_required(host, ios); |
| if (enable) { |
| sdhci_msm_bus_cancel_work_and_set_vote(host, bw); |
| } else { |
| /* |
| * If clock gating is enabled, then remove the vote |
| * immediately because clocks will be disabled only |
| * after SDHCI_MSM_MMC_CLK_GATE_DELAY and thus no |
| * additional delay is required to remove the bus vote. |
| */ |
| #ifdef CONFIG_MMC_CLKGATE |
| if (host->mmc->clkgate_delay) |
| sdhci_msm_bus_cancel_work_and_set_vote(host, 0); |
| else |
| #endif |
| sdhci_msm_bus_queue_work(host); |
| } |
| } |
| |
| /* Regulator utility functions */ |
| static int sdhci_msm_vreg_init_reg(struct device *dev, |
| struct sdhci_msm_reg_data *vreg) |
| { |
| int ret = 0; |
| |
| /* check if regulator is already initialized? */ |
| if (vreg->reg) |
| goto out; |
| |
| /* Get the regulator handle */ |
| vreg->reg = devm_regulator_get(dev, vreg->name); |
| if (IS_ERR(vreg->reg)) { |
| ret = PTR_ERR(vreg->reg); |
| pr_err("%s: devm_regulator_get(%s) failed. ret=%d\n", |
| __func__, vreg->name, ret); |
| goto out; |
| } |
| |
| if (regulator_count_voltages(vreg->reg) > 0) { |
| vreg->set_voltage_sup = true; |
| /* sanity check */ |
| if (!vreg->high_vol_level || !vreg->hpm_uA) { |
| pr_err("%s: %s invalid constraints specified\n", |
| __func__, vreg->name); |
| ret = -EINVAL; |
| } |
| } |
| |
| out: |
| return ret; |
| } |
| |
| static void sdhci_msm_vreg_deinit_reg(struct sdhci_msm_reg_data *vreg) |
| { |
| if (vreg->reg) |
| devm_regulator_put(vreg->reg); |
| } |
| |
| static int sdhci_msm_vreg_set_optimum_mode(struct sdhci_msm_reg_data |
| *vreg, int uA_load) |
| { |
| int ret = 0; |
| |
| /* |
| * regulators that do not support regulator_set_voltage also |
| * do not support regulator_set_optimum_mode |
| */ |
| if (vreg->set_voltage_sup) { |
| ret = regulator_set_load(vreg->reg, uA_load); |
| if (ret < 0) |
| pr_err("%s: regulator_set_load(reg=%s,uA_load=%d) failed. ret=%d\n", |
| __func__, vreg->name, uA_load, ret); |
| else |
| /* |
| * regulator_set_load() can return non zero |
| * value even for success case. |
| */ |
| ret = 0; |
| } |
| return ret; |
| } |
| |
| static int sdhci_msm_vreg_set_voltage(struct sdhci_msm_reg_data *vreg, |
| int min_uV, int max_uV) |
| { |
| int ret = 0; |
| if (vreg->set_voltage_sup) { |
| ret = regulator_set_voltage(vreg->reg, min_uV, max_uV); |
| if (ret) { |
| pr_err("%s: regulator_set_voltage(%s)failed. min_uV=%d,max_uV=%d,ret=%d\n", |
| __func__, vreg->name, min_uV, max_uV, ret); |
| } |
| } |
| |
| return ret; |
| } |
| |
| static int sdhci_msm_vreg_enable(struct sdhci_msm_reg_data *vreg) |
| { |
| int ret = 0; |
| |
| /* Put regulator in HPM (high power mode) */ |
| ret = sdhci_msm_vreg_set_optimum_mode(vreg, vreg->hpm_uA); |
| if (ret < 0) |
| return ret; |
| |
| if (!vreg->is_enabled) { |
| /* Set voltage level */ |
| ret = sdhci_msm_vreg_set_voltage(vreg, vreg->high_vol_level, |
| vreg->high_vol_level); |
| if (ret) |
| return ret; |
| } |
| ret = regulator_enable(vreg->reg); |
| if (ret) { |
| pr_err("%s: regulator_enable(%s) failed. ret=%d\n", |
| __func__, vreg->name, ret); |
| return ret; |
| } |
| vreg->is_enabled = true; |
| return ret; |
| } |
| |
| static int sdhci_msm_vreg_disable(struct sdhci_msm_reg_data *vreg) |
| { |
| int ret = 0; |
| |
| /* Never disable regulator marked as always_on */ |
| if (vreg->is_enabled && !vreg->is_always_on) { |
| ret = regulator_disable(vreg->reg); |
| if (ret) { |
| pr_err("%s: regulator_disable(%s) failed. ret=%d\n", |
| __func__, vreg->name, ret); |
| goto out; |
| } |
| vreg->is_enabled = false; |
| |
| ret = sdhci_msm_vreg_set_optimum_mode(vreg, 0); |
| if (ret < 0) |
| goto out; |
| |
| /* Set min. voltage level to 0 */ |
| ret = sdhci_msm_vreg_set_voltage(vreg, 0, vreg->high_vol_level); |
| if (ret) |
| goto out; |
| } else if (vreg->is_enabled && vreg->is_always_on) { |
| if (vreg->lpm_sup) { |
| /* Put always_on regulator in LPM (low power mode) */ |
| ret = sdhci_msm_vreg_set_optimum_mode(vreg, |
| vreg->lpm_uA); |
| if (ret < 0) |
| goto out; |
| } |
| } |
| out: |
| return ret; |
| } |
| |
| static int sdhci_msm_setup_vreg(struct sdhci_msm_pltfm_data *pdata, |
| bool enable, bool is_init) |
| { |
| int ret = 0, i; |
| struct sdhci_msm_slot_reg_data *curr_slot; |
| struct sdhci_msm_reg_data *vreg_table[2]; |
| |
| curr_slot = pdata->vreg_data; |
| if (!curr_slot) { |
| pr_debug("%s: vreg info unavailable,assuming the slot is powered by always on domain\n", |
| __func__); |
| goto out; |
| } |
| |
| vreg_table[0] = curr_slot->vdd_data; |
| vreg_table[1] = curr_slot->vdd_io_data; |
| |
| for (i = 0; i < ARRAY_SIZE(vreg_table); i++) { |
| if (vreg_table[i]) { |
| if (enable) |
| ret = sdhci_msm_vreg_enable(vreg_table[i]); |
| else |
| ret = sdhci_msm_vreg_disable(vreg_table[i]); |
| if (ret) |
| goto out; |
| } |
| } |
| out: |
| return ret; |
| } |
| |
| /* This init function should be called only once for each SDHC slot */ |
| static int sdhci_msm_vreg_init(struct device *dev, |
| struct sdhci_msm_pltfm_data *pdata, |
| bool is_init) |
| { |
| int ret = 0; |
| struct sdhci_msm_slot_reg_data *curr_slot; |
| struct sdhci_msm_reg_data *curr_vdd_reg, *curr_vdd_io_reg; |
| |
| curr_slot = pdata->vreg_data; |
| if (!curr_slot) |
| goto out; |
| |
| curr_vdd_reg = curr_slot->vdd_data; |
| curr_vdd_io_reg = curr_slot->vdd_io_data; |
| |
| if (!is_init) |
| /* Deregister all regulators from regulator framework */ |
| goto vdd_io_reg_deinit; |
| |
| /* |
| * Get the regulator handle from voltage regulator framework |
| * and then try to set the voltage level for the regulator |
| */ |
| if (curr_vdd_reg) { |
| ret = sdhci_msm_vreg_init_reg(dev, curr_vdd_reg); |
| if (ret) |
| goto out; |
| } |
| if (curr_vdd_io_reg) { |
| ret = sdhci_msm_vreg_init_reg(dev, curr_vdd_io_reg); |
| if (ret) |
| goto vdd_reg_deinit; |
| } |
| |
| if (ret) |
| dev_err(dev, "vreg reset failed (%d)\n", ret); |
| goto out; |
| |
| vdd_io_reg_deinit: |
| if (curr_vdd_io_reg) |
| sdhci_msm_vreg_deinit_reg(curr_vdd_io_reg); |
| vdd_reg_deinit: |
| if (curr_vdd_reg) |
| sdhci_msm_vreg_deinit_reg(curr_vdd_reg); |
| out: |
| return ret; |
| } |
| |
| |
| static int sdhci_msm_set_vdd_io_vol(struct sdhci_msm_pltfm_data *pdata, |
| enum vdd_io_level level, |
| unsigned int voltage_level) |
| { |
| int ret = 0; |
| int set_level; |
| struct sdhci_msm_reg_data *vdd_io_reg; |
| |
| if (!pdata->vreg_data) |
| return ret; |
| |
| vdd_io_reg = pdata->vreg_data->vdd_io_data; |
| if (vdd_io_reg && vdd_io_reg->is_enabled) { |
| switch (level) { |
| case VDD_IO_LOW: |
| set_level = vdd_io_reg->low_vol_level; |
| break; |
| case VDD_IO_HIGH: |
| set_level = vdd_io_reg->high_vol_level; |
| break; |
| case VDD_IO_SET_LEVEL: |
| set_level = voltage_level; |
| break; |
| default: |
| pr_err("%s: invalid argument level = %d", |
| __func__, level); |
| ret = -EINVAL; |
| return ret; |
| } |
| ret = sdhci_msm_vreg_set_voltage(vdd_io_reg, set_level, |
| set_level); |
| } |
| return ret; |
| } |
| |
| /* |
| * Acquire spin-lock host->lock before calling this function |
| */ |
| static void sdhci_msm_cfg_sdiowakeup_gpio_irq(struct sdhci_host *host, |
| bool enable) |
| { |
| struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); |
| struct sdhci_msm_host *msm_host = pltfm_host->priv; |
| |
| if (enable && !msm_host->is_sdiowakeup_enabled) |
| enable_irq(msm_host->pdata->sdiowakeup_irq); |
| else if (!enable && msm_host->is_sdiowakeup_enabled) |
| disable_irq_nosync(msm_host->pdata->sdiowakeup_irq); |
| else |
| dev_warn(&msm_host->pdev->dev, "%s: wakeup to config: %d curr: %d\n", |
| __func__, enable, msm_host->is_sdiowakeup_enabled); |
| msm_host->is_sdiowakeup_enabled = enable; |
| } |
| |
| static irqreturn_t sdhci_msm_sdiowakeup_irq(int irq, void *data) |
| { |
| struct sdhci_host *host = (struct sdhci_host *)data; |
| struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); |
| struct sdhci_msm_host *msm_host = pltfm_host->priv; |
| |
| unsigned long flags; |
| |
| pr_debug("%s: irq (%d) received\n", __func__, irq); |
| |
| spin_lock_irqsave(&host->lock, flags); |
| sdhci_msm_cfg_sdiowakeup_gpio_irq(host, false); |
| spin_unlock_irqrestore(&host->lock, flags); |
| msm_host->sdio_pending_processing = true; |
| |
| return IRQ_HANDLED; |
| } |
| |
| void sdhci_msm_dump_pwr_ctrl_regs(struct sdhci_host *host) |
| { |
| struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); |
| struct sdhci_msm_host *msm_host = pltfm_host->priv; |
| const struct sdhci_msm_offset *msm_host_offset = |
| msm_host->offset; |
| unsigned int irq_flags = 0; |
| struct irq_desc *pwr_irq_desc = irq_to_desc(msm_host->pwr_irq); |
| |
| if (pwr_irq_desc) |
| irq_flags = ACCESS_PRIVATE(pwr_irq_desc->irq_data.common, |
| state_use_accessors); |
| |
| pr_err("%s: PWRCTL_STATUS: 0x%08x | PWRCTL_MASK: 0x%08x | PWRCTL_CTL: 0x%08x, pwr isr state=0x%x\n", |
| mmc_hostname(host->mmc), |
| sdhci_msm_readl_relaxed(host, |
| msm_host_offset->CORE_PWRCTL_STATUS), |
| sdhci_msm_readl_relaxed(host, |
| msm_host_offset->CORE_PWRCTL_MASK), |
| sdhci_msm_readl_relaxed(host, |
| msm_host_offset->CORE_PWRCTL_CTL), irq_flags); |
| |
| MMC_TRACE(host->mmc, |
| "%s: Sts: 0x%08x | Mask: 0x%08x | Ctrl: 0x%08x, pwr isr state=0x%x\n", |
| __func__, |
| sdhci_msm_readb_relaxed(host, |
| msm_host_offset->CORE_PWRCTL_STATUS), |
| sdhci_msm_readb_relaxed(host, |
| msm_host_offset->CORE_PWRCTL_MASK), |
| sdhci_msm_readb_relaxed(host, |
| msm_host_offset->CORE_PWRCTL_CTL), irq_flags); |
| } |
| |
| static int sdhci_msm_clear_pwrctl_status(struct sdhci_host *host, u8 value) |
| { |
| struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); |
| struct sdhci_msm_host *msm_host = pltfm_host->priv; |
| const struct sdhci_msm_offset *msm_host_offset = msm_host->offset; |
| int ret = 0, retry = 10; |
| |
| /* |
| * There is a rare HW scenario where the first clear pulse could be |
| * lost when actual reset and clear/read of status register is |
| * happening at a time. Hence, retry for at least 10 times to make |
| * sure status register is cleared. Otherwise, this will result in |
| * a spurious power IRQ resulting in system instability. |
| */ |
| do { |
| if (retry == 0) { |
| pr_err("%s: Timedout clearing (0x%x) pwrctl status register\n", |
| mmc_hostname(host->mmc), value); |
| sdhci_msm_dump_pwr_ctrl_regs(host); |
| WARN_ON(1); |
| ret = -EBUSY; |
| break; |
| } |
| |
| /* |
| * Clear the PWRCTL_STATUS interrupt bits by writing to the |
| * corresponding bits in the PWRCTL_CLEAR register. |
| */ |
| sdhci_msm_writeb_relaxed(value, host, |
| msm_host_offset->CORE_PWRCTL_CLEAR); |
| /* |
| * SDHC has core_mem and hc_mem device memory and these memory |
| * addresses do not fall within 1KB region. Hence, any update |
| * to core_mem address space would require an mb() to ensure |
| * this gets completed before its next update to registers |
| * within hc_mem. |
| */ |
| mb(); |
| retry--; |
| udelay(10); |
| } while (value & sdhci_msm_readb_relaxed(host, |
| msm_host_offset->CORE_PWRCTL_STATUS)); |
| |
| return ret; |
| } |
| |
| static irqreturn_t sdhci_msm_pwr_irq(int irq, void *data) |
| { |
| struct sdhci_host *host = (struct sdhci_host *)data; |
| struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); |
| struct sdhci_msm_host *msm_host = pltfm_host->priv; |
| const struct sdhci_msm_offset *msm_host_offset = |
| msm_host->offset; |
| u8 irq_status = 0; |
| u8 irq_ack = 0; |
| int ret = 0; |
| int pwr_state = 0, io_level = 0; |
| unsigned long flags; |
| |
| irq_status = sdhci_msm_readb_relaxed(host, |
| msm_host_offset->CORE_PWRCTL_STATUS); |
| |
| pr_debug("%s: Received IRQ(%d), status=0x%x\n", |
| mmc_hostname(msm_host->mmc), irq, irq_status); |
| |
| sdhci_msm_clear_pwrctl_status(host, irq_status); |
| |
| /* Handle BUS ON/OFF*/ |
| if (irq_status & CORE_PWRCTL_BUS_ON) { |
| ret = sdhci_msm_setup_vreg(msm_host->pdata, true, false); |
| if (!ret) { |
| ret = sdhci_msm_setup_pins(msm_host->pdata, true); |
| ret |= sdhci_msm_set_vdd_io_vol(msm_host->pdata, |
| VDD_IO_HIGH, 0); |
| } |
| if (ret) |
| irq_ack |= CORE_PWRCTL_BUS_FAIL; |
| else |
| irq_ack |= CORE_PWRCTL_BUS_SUCCESS; |
| |
| pwr_state = REQ_BUS_ON; |
| io_level = REQ_IO_HIGH; |
| } |
| if (irq_status & CORE_PWRCTL_BUS_OFF) { |
| if (msm_host->pltfm_init_done) |
| ret = sdhci_msm_setup_vreg(msm_host->pdata, |
| false, false); |
| if (!ret) { |
| ret = sdhci_msm_setup_pins(msm_host->pdata, false); |
| ret |= sdhci_msm_set_vdd_io_vol(msm_host->pdata, |
| VDD_IO_LOW, 0); |
| } |
| if (ret) |
| irq_ack |= CORE_PWRCTL_BUS_FAIL; |
| else |
| irq_ack |= CORE_PWRCTL_BUS_SUCCESS; |
| |
| pwr_state = REQ_BUS_OFF; |
| io_level = REQ_IO_LOW; |
| } |
| /* Handle IO LOW/HIGH */ |
| if (irq_status & CORE_PWRCTL_IO_LOW) { |
| /* Switch voltage Low */ |
| ret = sdhci_msm_set_vdd_io_vol(msm_host->pdata, VDD_IO_LOW, 0); |
| if (ret) |
| irq_ack |= CORE_PWRCTL_IO_FAIL; |
| else |
| irq_ack |= CORE_PWRCTL_IO_SUCCESS; |
| |
| io_level = REQ_IO_LOW; |
| } |
| if (irq_status & CORE_PWRCTL_IO_HIGH) { |
| /* Switch voltage High */ |
| ret = sdhci_msm_set_vdd_io_vol(msm_host->pdata, VDD_IO_HIGH, 0); |
| if (ret) |
| irq_ack |= CORE_PWRCTL_IO_FAIL; |
| else |
| irq_ack |= CORE_PWRCTL_IO_SUCCESS; |
| |
| io_level = REQ_IO_HIGH; |
| } |
| |
| /* ACK status to the core */ |
| sdhci_msm_writeb_relaxed(irq_ack, host, |
| msm_host_offset->CORE_PWRCTL_CTL); |
| /* |
| * SDHC has core_mem and hc_mem device memory and these memory |
| * addresses do not fall within 1KB region. Hence, any update to |
| * core_mem address space would require an mb() to ensure this gets |
| * completed before its next update to registers within hc_mem. |
| */ |
| mb(); |
| if ((io_level & REQ_IO_HIGH) && |
| (msm_host->caps_0 & CORE_3_0V_SUPPORT) && |
| !msm_host->core_3_0v_support) |
| writel_relaxed((readl_relaxed(host->ioaddr + |
| msm_host_offset->CORE_VENDOR_SPEC) & |
| ~CORE_IO_PAD_PWR_SWITCH), host->ioaddr + |
| msm_host_offset->CORE_VENDOR_SPEC); |
| else if ((io_level & REQ_IO_LOW) || |
| (msm_host->caps_0 & CORE_1_8V_SUPPORT)) |
| writel_relaxed((readl_relaxed(host->ioaddr + |
| msm_host_offset->CORE_VENDOR_SPEC) | |
| CORE_IO_PAD_PWR_SWITCH), host->ioaddr + |
| msm_host_offset->CORE_VENDOR_SPEC); |
| mb(); |
| |
| pr_debug("%s: Handled IRQ(%d), ret=%d, ack=0x%x\n", |
| mmc_hostname(msm_host->mmc), irq, ret, irq_ack); |
| spin_lock_irqsave(&host->lock, flags); |
| if (pwr_state) |
| msm_host->curr_pwr_state = pwr_state; |
| if (io_level) |
| msm_host->curr_io_level = io_level; |
| complete(&msm_host->pwr_irq_completion); |
| spin_unlock_irqrestore(&host->lock, flags); |
| |
| return IRQ_HANDLED; |
| } |
| |
| static ssize_t |
| show_polling(struct device *dev, struct device_attribute *attr, char *buf) |
| { |
| struct sdhci_host *host = dev_get_drvdata(dev); |
| int poll; |
| unsigned long flags; |
| |
| spin_lock_irqsave(&host->lock, flags); |
| poll = !!(host->mmc->caps & MMC_CAP_NEEDS_POLL); |
| spin_unlock_irqrestore(&host->lock, flags); |
| |
| return snprintf(buf, PAGE_SIZE, "%d\n", poll); |
| } |
| |
| static ssize_t |
| store_polling(struct device *dev, struct device_attribute *attr, |
| const char *buf, size_t count) |
| { |
| struct sdhci_host *host = dev_get_drvdata(dev); |
| int value; |
| unsigned long flags; |
| |
| if (!kstrtou32(buf, 0, &value)) { |
| spin_lock_irqsave(&host->lock, flags); |
| if (value) { |
| host->mmc->caps |= MMC_CAP_NEEDS_POLL; |
| mmc_detect_change(host->mmc, 0); |
| } else { |
| host->mmc->caps &= ~MMC_CAP_NEEDS_POLL; |
| } |
| spin_unlock_irqrestore(&host->lock, flags); |
| } |
| return count; |
| } |
| |
| static ssize_t |
| show_sdhci_max_bus_bw(struct device *dev, struct device_attribute *attr, |
| char *buf) |
| { |
| struct sdhci_host *host = dev_get_drvdata(dev); |
| struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); |
| struct sdhci_msm_host *msm_host = pltfm_host->priv; |
| |
| return snprintf(buf, PAGE_SIZE, "%u\n", |
| msm_host->msm_bus_vote.is_max_bw_needed); |
| } |
| |
| static ssize_t |
| store_sdhci_max_bus_bw(struct device *dev, struct device_attribute *attr, |
| const char *buf, size_t count) |
| { |
| struct sdhci_host *host = dev_get_drvdata(dev); |
| struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); |
| struct sdhci_msm_host *msm_host = pltfm_host->priv; |
| uint32_t value; |
| unsigned long flags; |
| |
| if (!kstrtou32(buf, 0, &value)) { |
| spin_lock_irqsave(&host->lock, flags); |
| msm_host->msm_bus_vote.is_max_bw_needed = !!value; |
| spin_unlock_irqrestore(&host->lock, flags); |
| } |
| return count; |
| } |
| |
| static void sdhci_msm_check_power_status(struct sdhci_host *host, u32 req_type) |
| { |
| struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); |
| struct sdhci_msm_host *msm_host = pltfm_host->priv; |
| const struct sdhci_msm_offset *msm_host_offset = |
| msm_host->offset; |
| unsigned long flags; |
| bool done = false; |
| u32 io_sig_sts = SWITCHABLE_SIGNALLING_VOL; |
| |
| spin_lock_irqsave(&host->lock, flags); |
| pr_debug("%s: %s: request %d curr_pwr_state %x curr_io_level %x\n", |
| mmc_hostname(host->mmc), __func__, req_type, |
| msm_host->curr_pwr_state, msm_host->curr_io_level); |
| if (!msm_host->mci_removed) |
| io_sig_sts = sdhci_msm_readl_relaxed(host, |
| msm_host_offset->CORE_GENERICS); |
| |
| /* |
| * The IRQ for request type IO High/Low will be generated when - |
| * 1. SWITCHABLE_SIGNALLING_VOL is enabled in HW. |
| * 2. If 1 is true and when there is a state change in 1.8V enable |
| * bit (bit 3) of SDHCI_HOST_CONTROL2 register. The reset state of |
| * that bit is 0 which indicates 3.3V IO voltage. So, when MMC core |
| * layer tries to set it to 3.3V before card detection happens, the |
| * IRQ doesn't get triggered as there is no state change in this bit. |
| * The driver already handles this case by changing the IO voltage |
| * level to high as part of controller power up sequence. Hence, check |
| * for host->pwr to handle a case where IO voltage high request is |
| * issued even before controller power up. |
| */ |
| if (req_type & (REQ_IO_HIGH | REQ_IO_LOW)) { |
| if (!(io_sig_sts & SWITCHABLE_SIGNALLING_VOL) || |
| ((req_type & REQ_IO_HIGH) && !host->pwr)) { |
| pr_debug("%s: do not wait for power IRQ that never comes\n", |
| mmc_hostname(host->mmc)); |
| spin_unlock_irqrestore(&host->lock, flags); |
| return; |
| } |
| } |
| |
| if ((req_type & msm_host->curr_pwr_state) || |
| (req_type & msm_host->curr_io_level)) |
| done = true; |
| spin_unlock_irqrestore(&host->lock, flags); |
| |
| /* |
| * This is needed here to hanlde a case where IRQ gets |
| * triggered even before this function is called so that |
| * x->done counter of completion gets reset. Otherwise, |
| * next call to wait_for_completion returns immediately |
| * without actually waiting for the IRQ to be handled. |
| */ |
| if (done) |
| init_completion(&msm_host->pwr_irq_completion); |
| else if (!wait_for_completion_timeout(&msm_host->pwr_irq_completion, |
| msecs_to_jiffies(MSM_PWR_IRQ_TIMEOUT_MS))) { |
| __WARN_printf("%s: request(%d) timed out waiting for pwr_irq\n", |
| mmc_hostname(host->mmc), req_type); |
| MMC_TRACE(host->mmc, |
| "%s: request(%d) timed out waiting for pwr_irq\n", |
| __func__, req_type); |
| sdhci_msm_dump_pwr_ctrl_regs(host); |
| } |
| pr_debug("%s: %s: request %d done\n", mmc_hostname(host->mmc), |
| __func__, req_type); |
| } |
| |
| static void sdhci_msm_toggle_cdr(struct sdhci_host *host, bool enable) |
| { |
| struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); |
| struct sdhci_msm_host *msm_host = pltfm_host->priv; |
| const struct sdhci_msm_offset *msm_host_offset = |
| msm_host->offset; |
| u32 config = readl_relaxed(host->ioaddr + |
| msm_host_offset->CORE_DLL_CONFIG); |
| |
| if (enable) { |
| config |= CORE_CDR_EN; |
| config &= ~CORE_CDR_EXT_EN; |
| writel_relaxed(config, host->ioaddr + |
| msm_host_offset->CORE_DLL_CONFIG); |
| } else { |
| config &= ~CORE_CDR_EN; |
| config |= CORE_CDR_EXT_EN; |
| writel_relaxed(config, host->ioaddr + |
| msm_host_offset->CORE_DLL_CONFIG); |
| } |
| } |
| |
| static unsigned int sdhci_msm_max_segs(void) |
| { |
| return SDHCI_MSM_MAX_SEGMENTS; |
| } |
| |
| static unsigned int sdhci_msm_get_min_clock(struct sdhci_host *host) |
| { |
| struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); |
| struct sdhci_msm_host *msm_host = pltfm_host->priv; |
| |
| return msm_host->pdata->sup_clk_table[0]; |
| } |
| |
| static unsigned int sdhci_msm_get_max_clock(struct sdhci_host *host) |
| { |
| struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); |
| struct sdhci_msm_host *msm_host = pltfm_host->priv; |
| int max_clk_index = msm_host->pdata->sup_clk_cnt; |
| |
| return msm_host->pdata->sup_clk_table[max_clk_index - 1]; |
| } |
| |
| static unsigned int sdhci_msm_get_sup_clk_rate(struct sdhci_host *host, |
| u32 req_clk) |
| { |
| struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); |
| struct sdhci_msm_host *msm_host = pltfm_host->priv; |
| unsigned int sel_clk = -1; |
| unsigned char cnt; |
| |
| if (req_clk < sdhci_msm_get_min_clock(host)) { |
| sel_clk = sdhci_msm_get_min_clock(host); |
| return sel_clk; |
| } |
| |
| for (cnt = 0; cnt < msm_host->pdata->sup_clk_cnt; cnt++) { |
| if (msm_host->pdata->sup_clk_table[cnt] > req_clk) { |
| break; |
| } else if (msm_host->pdata->sup_clk_table[cnt] == req_clk) { |
| sel_clk = msm_host->pdata->sup_clk_table[cnt]; |
| break; |
| } else { |
| sel_clk = msm_host->pdata->sup_clk_table[cnt]; |
| } |
| } |
| return sel_clk; |
| } |
| |
| static long sdhci_msm_get_bus_aggr_clk_rate(struct sdhci_host *host, |
| u32 apps_clk) |
| { |
| struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); |
| struct sdhci_msm_host *msm_host = pltfm_host->priv; |
| long sel_clk = -1; |
| unsigned char cnt; |
| |
| if (msm_host->pdata->bus_clk_cnt != msm_host->pdata->sup_clk_cnt) { |
| pr_err("%s: %s: mismatch between bus_clk_cnt(%u) and apps_clk_cnt(%u)\n", |
| mmc_hostname(host->mmc), __func__, |
| (unsigned int)msm_host->pdata->bus_clk_cnt, |
| (unsigned int)msm_host->pdata->sup_clk_cnt); |
| return msm_host->pdata->bus_clk_table[0]; |
| } |
| if (apps_clk == sdhci_msm_get_min_clock(host)) { |
| sel_clk = msm_host->pdata->bus_clk_table[0]; |
| return sel_clk; |
| } |
| |
| for (cnt = 0; cnt < msm_host->pdata->bus_clk_cnt; cnt++) { |
| if (msm_host->pdata->sup_clk_table[cnt] > apps_clk) |
| break; |
| sel_clk = msm_host->pdata->bus_clk_table[cnt]; |
| } |
| return sel_clk; |
| } |
| |
| static void sdhci_msm_registers_save(struct sdhci_host *host) |
| { |
| struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); |
| struct sdhci_msm_host *msm_host = pltfm_host->priv; |
| const struct sdhci_msm_offset *msm_host_offset = |
| msm_host->offset; |
| |
| if (!msm_host->regs_restore.is_supported) |
| return; |
| |
| msm_host->regs_restore.vendor_func = readl_relaxed(host->ioaddr + |
| msm_host_offset->CORE_VENDOR_SPEC); |
| msm_host->regs_restore.vendor_pwrctl_mask = |
| readl_relaxed(host->ioaddr + |
| msm_host_offset->CORE_PWRCTL_MASK); |
| msm_host->regs_restore.vendor_func2 = |
| readl_relaxed(host->ioaddr + |
| msm_host_offset->CORE_VENDOR_SPEC_FUNC2); |
| msm_host->regs_restore.vendor_func3 = |
| readl_relaxed(host->ioaddr + |
| msm_host_offset->CORE_VENDOR_SPEC3); |
| msm_host->regs_restore.hc_2c_2e = |
| sdhci_readl(host, SDHCI_CLOCK_CONTROL); |
| msm_host->regs_restore.hc_3c_3e = |
| sdhci_readl(host, SDHCI_AUTO_CMD_ERR); |
| msm_host->regs_restore.vendor_pwrctl_ctl = |
| readl_relaxed(host->ioaddr + |
| msm_host_offset->CORE_PWRCTL_CTL); |
| msm_host->regs_restore.hc_38_3a = |
| sdhci_readl(host, SDHCI_SIGNAL_ENABLE); |
| msm_host->regs_restore.hc_34_36 = |
| sdhci_readl(host, SDHCI_INT_ENABLE); |
| msm_host->regs_restore.hc_28_2a = |
| sdhci_readl(host, SDHCI_HOST_CONTROL); |
| msm_host->regs_restore.vendor_caps_0 = |
| readl_relaxed(host->ioaddr + |
| msm_host_offset->CORE_VENDOR_SPEC_CAPABILITIES0); |
| msm_host->regs_restore.hc_caps_1 = |
| sdhci_readl(host, SDHCI_CAPABILITIES_1); |
| msm_host->regs_restore.testbus_config = readl_relaxed(host->ioaddr + |
| msm_host_offset->CORE_TESTBUS_CONFIG); |
| msm_host->regs_restore.dll_config = readl_relaxed(host->ioaddr + |
| msm_host_offset->CORE_DLL_CONFIG); |
| msm_host->regs_restore.dll_config2 = readl_relaxed(host->ioaddr + |
| msm_host_offset->CORE_DLL_CONFIG_2); |
| msm_host->regs_restore.dll_config = readl_relaxed(host->ioaddr + |
| msm_host_offset->CORE_DLL_CONFIG); |
| msm_host->regs_restore.dll_config2 = readl_relaxed(host->ioaddr + |
| msm_host_offset->CORE_DLL_CONFIG_2); |
| msm_host->regs_restore.dll_config3 = readl_relaxed(host->ioaddr + |
| msm_host_offset->CORE_DLL_CONFIG_3); |
| msm_host->regs_restore.dll_usr_ctl = readl_relaxed(host->ioaddr + |
| msm_host_offset->CORE_DLL_USR_CTL); |
| |
| msm_host->regs_restore.is_valid = true; |
| |
| pr_debug("%s: %s: registers saved. PWRCTL_MASK = 0x%x\n", |
| mmc_hostname(host->mmc), __func__, |
| readl_relaxed(host->ioaddr + |
| msm_host_offset->CORE_PWRCTL_MASK)); |
| } |
| |
| static void sdhci_msm_registers_restore(struct sdhci_host *host) |
| { |
| struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); |
| struct sdhci_msm_host *msm_host = pltfm_host->priv; |
| u8 irq_status; |
| const struct sdhci_msm_offset *msm_host_offset = |
| msm_host->offset; |
| struct mmc_ios ios = host->mmc->ios; |
| |
| if (!msm_host->regs_restore.is_supported || |
| !msm_host->regs_restore.is_valid) |
| return; |
| |
| writel_relaxed(0, host->ioaddr + msm_host_offset->CORE_PWRCTL_MASK); |
| writel_relaxed(msm_host->regs_restore.vendor_func, host->ioaddr + |
| msm_host_offset->CORE_VENDOR_SPEC); |
| writel_relaxed(msm_host->regs_restore.vendor_func2, |
| host->ioaddr + |
| msm_host_offset->CORE_VENDOR_SPEC_FUNC2); |
| writel_relaxed(msm_host->regs_restore.vendor_func3, |
| host->ioaddr + |
| msm_host_offset->CORE_VENDOR_SPEC3); |
| sdhci_writel(host, msm_host->regs_restore.hc_2c_2e, |
| SDHCI_CLOCK_CONTROL); |
| sdhci_writel(host, msm_host->regs_restore.hc_3c_3e, |
| SDHCI_AUTO_CMD_ERR); |
| sdhci_writel(host, msm_host->regs_restore.hc_38_3a, |
| SDHCI_SIGNAL_ENABLE); |
| sdhci_writel(host, msm_host->regs_restore.hc_34_36, |
| SDHCI_INT_ENABLE); |
| sdhci_writel(host, msm_host->regs_restore.hc_28_2a, |
| SDHCI_HOST_CONTROL); |
| writel_relaxed(msm_host->regs_restore.vendor_caps_0, |
| host->ioaddr + |
| msm_host_offset->CORE_VENDOR_SPEC_CAPABILITIES0); |
| sdhci_writel(host, msm_host->regs_restore.hc_caps_1, |
| SDHCI_CAPABILITIES_1); |
| writel_relaxed(msm_host->regs_restore.testbus_config, host->ioaddr + |
| msm_host_offset->CORE_TESTBUS_CONFIG); |
| msm_host->regs_restore.is_valid = false; |
| |
| /* |
| * Clear the PWRCTL_STATUS register. |
| * There is a rare HW scenario where the first clear pulse could be |
| * lost when actual reset and clear/read of status register is |
| * happening at a time. Hence, retry for at least 10 times to make |
| * sure status register is cleared. Otherwise, this will result in |
| * a spurious power IRQ resulting in system instability. |
| */ |
| irq_status = sdhci_msm_readb_relaxed(host, |
| msm_host_offset->CORE_PWRCTL_STATUS); |
| |
| sdhci_msm_clear_pwrctl_status(host, irq_status); |
| |
| writel_relaxed(msm_host->regs_restore.vendor_pwrctl_ctl, |
| host->ioaddr + msm_host_offset->CORE_PWRCTL_CTL); |
| writel_relaxed(msm_host->regs_restore.vendor_pwrctl_mask, |
| host->ioaddr + msm_host_offset->CORE_PWRCTL_MASK); |
| |
| if (((ios.timing == MMC_TIMING_MMC_HS400) || |
| (ios.timing == MMC_TIMING_MMC_HS200) || |
| (ios.timing == MMC_TIMING_UHS_SDR104)) |
| && (ios.clock > CORE_FREQ_100MHZ)) { |
| writel_relaxed(msm_host->regs_restore.dll_config2, |
| host->ioaddr + msm_host_offset->CORE_DLL_CONFIG_2); |
| writel_relaxed(msm_host->regs_restore.dll_config3, |
| host->ioaddr + msm_host_offset->CORE_DLL_CONFIG_3); |
| writel_relaxed(msm_host->regs_restore.dll_usr_ctl, |
| host->ioaddr + msm_host_offset->CORE_DLL_USR_CTL); |
| writel_relaxed(msm_host->regs_restore.dll_config & |
| ~(CORE_DLL_RST | CORE_DLL_PDN), |
| host->ioaddr + msm_host_offset->CORE_DLL_CONFIG); |
| |
| msm_init_cm_dll(host, DLL_INIT_FROM_CX_COLLAPSE_EXIT); |
| msm_config_cm_dll_phase(host, msm_host->saved_tuning_phase); |
| } |
| |
| pr_debug("%s: %s: registers restored. PWRCTL_MASK = 0x%x\n", |
| mmc_hostname(host->mmc), __func__, |
| readl_relaxed(host->ioaddr + |
| msm_host_offset->CORE_PWRCTL_MASK)); |
| } |
| |
| static int sdhci_msm_enable_controller_clock(struct sdhci_host *host) |
| { |
| struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); |
| struct sdhci_msm_host *msm_host = pltfm_host->priv; |
| int rc = 0; |
| |
| if (atomic_read(&msm_host->controller_clock)) |
| return 0; |
| |
| sdhci_msm_bus_voting(host, 1); |
| |
| if (!IS_ERR(msm_host->pclk)) { |
| rc = clk_prepare_enable(msm_host->pclk); |
| if (rc) { |
| pr_err("%s: %s: failed to enable the pclk with error %d\n", |
| mmc_hostname(host->mmc), __func__, rc); |
| goto remove_vote; |
| } |
| } |
| |
| if (!IS_ERR(msm_host->bus_aggr_clk)) { |
| rc = clk_prepare_enable(msm_host->bus_aggr_clk); |
| if (rc) { |
| pr_err("%s: %s: failed to enable the bus aggr clk with error %d\n", |
| mmc_hostname(host->mmc), __func__, rc); |
| goto disable_pclk; |
| } |
| } |
| |
| rc = clk_prepare_enable(msm_host->clk); |
| if (rc) { |
| pr_err("%s: %s: failed to enable the host-clk with error %d\n", |
| mmc_hostname(host->mmc), __func__, rc); |
| goto disable_bus_aggr_clk; |
| } |
| |
| if (!IS_ERR(msm_host->ice_clk)) { |
| rc = clk_prepare_enable(msm_host->ice_clk); |
| if (rc) { |
| pr_err("%s: %s: failed to enable the ice-clk with error %d\n", |
| mmc_hostname(host->mmc), __func__, rc); |
| goto disable_host_clk; |
| } |
| } |
| atomic_set(&msm_host->controller_clock, 1); |
| pr_debug("%s: %s: enabled controller clock\n", |
| mmc_hostname(host->mmc), __func__); |
| sdhci_msm_registers_restore(host); |
| goto out; |
| |
| disable_host_clk: |
| if (!IS_ERR(msm_host->clk)) |
| clk_disable_unprepare(msm_host->clk); |
| disable_bus_aggr_clk: |
| if (!IS_ERR(msm_host->bus_aggr_clk)) |
| clk_disable_unprepare(msm_host->bus_aggr_clk); |
| disable_pclk: |
| if (!IS_ERR(msm_host->pclk)) |
| clk_disable_unprepare(msm_host->pclk); |
| remove_vote: |
| if (msm_host->msm_bus_vote.client_handle) |
| sdhci_msm_bus_cancel_work_and_set_vote(host, 0); |
| out: |
| return rc; |
| } |
| |
| static void sdhci_msm_disable_controller_clock(struct sdhci_host *host) |
| { |
| struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); |
| struct sdhci_msm_host *msm_host = pltfm_host->priv; |
| |
| if (atomic_read(&msm_host->controller_clock)) { |
| sdhci_msm_registers_save(host); |
| if (!IS_ERR(msm_host->clk)) |
| clk_disable_unprepare(msm_host->clk); |
| if (!IS_ERR(msm_host->ice_clk)) |
| clk_disable_unprepare(msm_host->ice_clk); |
| if (!IS_ERR(msm_host->bus_aggr_clk)) |
| clk_disable_unprepare(msm_host->bus_aggr_clk); |
| if (!IS_ERR(msm_host->pclk)) |
| clk_disable_unprepare(msm_host->pclk); |
| sdhci_msm_bus_voting(host, 0); |
| atomic_set(&msm_host->controller_clock, 0); |
| pr_debug("%s: %s: disabled controller clock\n", |
| mmc_hostname(host->mmc), __func__); |
| } |
| } |
| |
| static int sdhci_msm_prepare_clocks(struct sdhci_host *host, bool enable) |
| { |
| struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); |
| struct sdhci_msm_host *msm_host = pltfm_host->priv; |
| int rc = 0; |
| |
| if (enable && !atomic_read(&msm_host->clks_on)) { |
| pr_debug("%s: request to enable clocks\n", |
| mmc_hostname(host->mmc)); |
| |
| /* |
| * The bus-width or the clock rate might have changed |
| * after controller clocks are enbaled, update bus vote |
| * in such case. |
| */ |
| if (atomic_read(&msm_host->controller_clock)) |
| sdhci_msm_bus_voting(host, 1); |
| |
| rc = sdhci_msm_enable_controller_clock(host); |
| if (rc) |
| goto remove_vote; |
| |
| if (!IS_ERR_OR_NULL(msm_host->bus_clk)) { |
| rc = clk_prepare_enable(msm_host->bus_clk); |
| if (rc) { |
| pr_err("%s: %s: failed to enable the bus-clock with error %d\n", |
| mmc_hostname(host->mmc), __func__, rc); |
| goto disable_controller_clk; |
| } |
| } |
| if (!IS_ERR(msm_host->ff_clk)) { |
| rc = clk_prepare_enable(msm_host->ff_clk); |
| if (rc) { |
| pr_err("%s: %s: failed to enable the ff_clk with error %d\n", |
| mmc_hostname(host->mmc), __func__, rc); |
| goto disable_bus_clk; |
| } |
| } |
| if (!IS_ERR(msm_host->sleep_clk)) { |
| rc = clk_prepare_enable(msm_host->sleep_clk); |
| if (rc) { |
| pr_err("%s: %s: failed to enable the sleep_clk with error %d\n", |
| mmc_hostname(host->mmc), __func__, rc); |
| goto disable_ff_clk; |
| } |
| } |
| mb(); |
| |
| } else if (!enable && atomic_read(&msm_host->clks_on)) { |
| sdhci_writew(host, 0, SDHCI_CLOCK_CONTROL); |
| mb(); |
| /* |
| * During 1.8V signal switching the clock source must |
| * still be ON as it requires accessing SDHC |
| * registers (SDHCi host control2 register bit 3 must |
| * be written and polled after stopping the SDCLK). |
| */ |
| if (host->mmc->card_clock_off) |
| return 0; |
| pr_debug("%s: request to disable clocks\n", |
| mmc_hostname(host->mmc)); |
| if (!IS_ERR_OR_NULL(msm_host->sleep_clk)) |
| clk_disable_unprepare(msm_host->sleep_clk); |
| if (!IS_ERR_OR_NULL(msm_host->ff_clk)) |
| clk_disable_unprepare(msm_host->ff_clk); |
| if (!IS_ERR_OR_NULL(msm_host->bus_clk)) |
| clk_disable_unprepare(msm_host->bus_clk); |
| sdhci_msm_disable_controller_clock(host); |
| } |
| atomic_set(&msm_host->clks_on, enable); |
| goto out; |
| disable_ff_clk: |
| if (!IS_ERR_OR_NULL(msm_host->ff_clk)) |
| clk_disable_unprepare(msm_host->ff_clk); |
| disable_bus_clk: |
| if (!IS_ERR_OR_NULL(msm_host->bus_clk)) |
| clk_disable_unprepare(msm_host->bus_clk); |
| disable_controller_clk: |
| if (!IS_ERR_OR_NULL(msm_host->clk)) |
| clk_disable_unprepare(msm_host->clk); |
| if (!IS_ERR(msm_host->ice_clk)) |
| clk_disable_unprepare(msm_host->ice_clk); |
| if (!IS_ERR_OR_NULL(msm_host->bus_aggr_clk)) |
| clk_disable_unprepare(msm_host->bus_aggr_clk); |
| if (!IS_ERR_OR_NULL(msm_host->pclk)) |
| clk_disable_unprepare(msm_host->pclk); |
| atomic_set(&msm_host->controller_clock, 0); |
| remove_vote: |
| if (msm_host->msm_bus_vote.client_handle) |
| sdhci_msm_bus_cancel_work_and_set_vote(host, 0); |
| out: |
| return rc; |
| } |
| |
| static void sdhci_msm_set_clock(struct sdhci_host *host, unsigned int clock) |
| { |
| int rc; |
| struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); |
| struct sdhci_msm_host *msm_host = pltfm_host->priv; |
| const struct sdhci_msm_offset *msm_host_offset = |
| msm_host->offset; |
| struct mmc_card *card = host->mmc->card; |
| struct mmc_ios curr_ios = host->mmc->ios; |
| u32 sup_clock, ddr_clock, dll_lock; |
| long bus_clk_rate; |
| bool curr_pwrsave; |
| |
| if (!clock) { |
| /* |
| * disable pwrsave to ensure clock is not auto-gated until |
| * the rate is >400KHz (initialization complete). |
| */ |
| writel_relaxed(readl_relaxed(host->ioaddr + |
| msm_host_offset->CORE_VENDOR_SPEC) & |
| ~CORE_CLK_PWRSAVE, host->ioaddr + |
| msm_host_offset->CORE_VENDOR_SPEC); |
| sdhci_msm_prepare_clocks(host, false); |
| host->clock = clock; |
| goto out; |
| } |
| |
| rc = sdhci_msm_prepare_clocks(host, true); |
| if (rc) |
| goto out; |
| |
| curr_pwrsave = !!(readl_relaxed(host->ioaddr + |
| msm_host_offset->CORE_VENDOR_SPEC) & CORE_CLK_PWRSAVE); |
| if ((clock > 400000) && |
| !curr_pwrsave && card && mmc_host_may_gate_card(card)) |
| writel_relaxed(readl_relaxed(host->ioaddr + |
| msm_host_offset->CORE_VENDOR_SPEC) |
| | CORE_CLK_PWRSAVE, host->ioaddr + |
| msm_host_offset->CORE_VENDOR_SPEC); |
| /* |
| * Disable pwrsave for a newly added card if doesn't allow clock |
| * gating. |
| */ |
| else if (curr_pwrsave && card && !mmc_host_may_gate_card(card)) |
| writel_relaxed(readl_relaxed(host->ioaddr + |
| msm_host_offset->CORE_VENDOR_SPEC) |
| & ~CORE_CLK_PWRSAVE, host->ioaddr + |
| msm_host_offset->CORE_VENDOR_SPEC); |
| |
| sup_clock = sdhci_msm_get_sup_clk_rate(host, clock); |
| if ((curr_ios.timing == MMC_TIMING_UHS_DDR50) || |
| (curr_ios.timing == MMC_TIMING_MMC_DDR52) || |
| (curr_ios.timing == MMC_TIMING_MMC_HS400)) { |
| /* |
| * The SDHC requires internal clock frequency to be double the |
| * actual clock that will be set for DDR mode. The controller |
| * uses the faster clock(100/400MHz) for some of its parts and |
| * send the actual required clock (50/200MHz) to the card. |
| */ |
| ddr_clock = clock * 2; |
| sup_clock = sdhci_msm_get_sup_clk_rate(host, |
| ddr_clock); |
| } |
| |
| /* |
| * In general all timing modes are controlled via UHS mode select in |
| * Host Control2 register. eMMC specific HS200/HS400 doesn't have |
| * their respective modes defined here, hence we use these values. |
| * |
| * HS200 - SDR104 (Since they both are equivalent in functionality) |
| * HS400 - This involves multiple configurations |
| * Initially SDR104 - when tuning is required as HS200 |
| * Then when switching to DDR @ 400MHz (HS400) we use |
| * the vendor specific HC_SELECT_IN to control the mode. |
| * |
| * In addition to controlling the modes we also need to select the |
| * correct input clock for DLL depending on the mode. |
| * |
| * HS400 - divided clock (free running MCLK/2) |
| * All other modes - default (free running MCLK) |
| */ |
| if (curr_ios.timing == MMC_TIMING_MMC_HS400) { |
| /* Select the divided clock (free running MCLK/2) */ |
| writel_relaxed(((readl_relaxed(host->ioaddr + |
| msm_host_offset->CORE_VENDOR_SPEC) |
| & ~CORE_HC_MCLK_SEL_MASK) |
| | CORE_HC_MCLK_SEL_HS400), host->ioaddr + |
| msm_host_offset->CORE_VENDOR_SPEC); |
| /* |
| * Select HS400 mode using the HC_SELECT_IN from VENDOR SPEC |
| * register |
| */ |
| if ((msm_host->tuning_done || |
| (card && mmc_card_strobe(card) && |
| msm_host->enhanced_strobe)) && |
| !msm_host->calibration_done) { |
| /* |
| * Write 0x6 to HC_SELECT_IN and 1 to HC_SELECT_IN_EN |
| * field in VENDOR_SPEC_FUNC |
| */ |
| writel_relaxed((readl_relaxed(host->ioaddr + \ |
| msm_host_offset->CORE_VENDOR_SPEC) |
| | CORE_HC_SELECT_IN_HS400 |
| | CORE_HC_SELECT_IN_EN), host->ioaddr + |
| msm_host_offset->CORE_VENDOR_SPEC); |
| } |
| /* |
| * After MCLK ugating, toggle the FIFO write clock to get |
| * the FIFO pointers and flags to valid state. |
| */ |
| if (msm_host->tuning_done || |
| (card && mmc_card_strobe(card) && |
| msm_host->enhanced_strobe)) { |
| /* |
| * set HC_REG_DLL_CONFIG_3[1] to select MCLK as |
| * DLL input clock |
| */ |
| writel_relaxed(((readl_relaxed(host->ioaddr + |
| msm_host_offset->CORE_DLL_CONFIG_3)) |
| | RCLK_TOGGLE), host->ioaddr + |
| msm_host_offset->CORE_DLL_CONFIG_3); |
| /* ensure above write as toggling same bit quickly */ |
| wmb(); |
| udelay(2); |
| /* |
| * clear HC_REG_DLL_CONFIG_3[1] to select RCLK as |
| * DLL input clock |
| */ |
| writel_relaxed(((readl_relaxed(host->ioaddr + |
| msm_host_offset->CORE_DLL_CONFIG_3)) |
| & ~RCLK_TOGGLE), host->ioaddr + |
| msm_host_offset->CORE_DLL_CONFIG_3); |
| } |
| if (!host->mmc->ios.old_rate && !msm_host->use_cdclp533) { |
| /* |
| * Poll on DLL_LOCK and DDR_DLL_LOCK bits in |
| * CORE_DLL_STATUS to be set. This should get set |
| * with in 15 us at 200 MHz. |
| */ |
| rc = readl_poll_timeout(host->ioaddr + |
| msm_host_offset->CORE_DLL_STATUS, |
| dll_lock, (dll_lock & (CORE_DLL_LOCK | |
| CORE_DDR_DLL_LOCK)), 10, 1000); |
| if (rc == -ETIMEDOUT) |
| pr_err("%s: Unable to get DLL_LOCK/DDR_DLL_LOCK, dll_status: 0x%08x\n", |
| mmc_hostname(host->mmc), |
| dll_lock); |
| } |
| } else { |
| if (!msm_host->use_cdclp533) |
| /* set CORE_PWRSAVE_DLL bit in CORE_VENDOR_SPEC3 */ |
| writel_relaxed((readl_relaxed(host->ioaddr + |
| msm_host_offset->CORE_VENDOR_SPEC3) |
| & ~CORE_PWRSAVE_DLL), host->ioaddr + |
| msm_host_offset->CORE_VENDOR_SPEC3); |
| |
| /* Select the default clock (free running MCLK) */ |
| writel_relaxed(((readl_relaxed(host->ioaddr + |
| msm_host_offset->CORE_VENDOR_SPEC) |
| & ~CORE_HC_MCLK_SEL_MASK) |
| | CORE_HC_MCLK_SEL_DFLT), host->ioaddr + |
| msm_host_offset->CORE_VENDOR_SPEC); |
| |
| /* |
| * Disable HC_SELECT_IN to be able to use the UHS mode select |
| * configuration from Host Control2 register for all other |
| * modes. |
| * |
| * Write 0 to HC_SELECT_IN and HC_SELECT_IN_EN field |
| * in VENDOR_SPEC_FUNC |
| */ |
| writel_relaxed((readl_relaxed(host->ioaddr + |
| msm_host_offset->CORE_VENDOR_SPEC) |
| & ~CORE_HC_SELECT_IN_EN |
| & ~CORE_HC_SELECT_IN_MASK), host->ioaddr + |
| msm_host_offset->CORE_VENDOR_SPEC); |
| } |
| mb(); |
| |
| if (sup_clock != msm_host->clk_rate) { |
| pr_debug("%s: %s: setting clk rate to %u\n", |
| mmc_hostname(host->mmc), __func__, sup_clock); |
| rc = clk_set_rate(msm_host->clk, sup_clock); |
| if (rc) { |
| pr_err("%s: %s: Failed to set rate %u for host-clk : %d\n", |
| mmc_hostname(host->mmc), __func__, |
| sup_clock, rc); |
| goto out; |
| } |
| msm_host->clk_rate = sup_clock; |
| host->clock = clock; |
| |
| if (!IS_ERR(msm_host->bus_aggr_clk) && |
| msm_host->pdata->bus_clk_cnt) { |
| bus_clk_rate = sdhci_msm_get_bus_aggr_clk_rate(host, |
| sup_clock); |
| if (bus_clk_rate >= 0) { |
| rc = clk_set_rate(msm_host->bus_aggr_clk, |
| bus_clk_rate); |
| if (rc) { |
| pr_err("%s: %s: Failed to set rate %ld for bus-aggr-clk : %d\n", |
| mmc_hostname(host->mmc), |
| __func__, bus_clk_rate, rc); |
| goto out; |
| } |
| } else { |
| pr_err("%s: %s: Unsupported apps clk rate %u for bus-aggr-clk, err: %ld\n", |
| mmc_hostname(host->mmc), __func__, |
| sup_clock, bus_clk_rate); |
| } |
| } |
| |
| /* Configure pinctrl drive type according to |
| * current clock rate |
| */ |
| rc = sdhci_msm_config_pinctrl_drv_type(msm_host->pdata, clock); |
| if (rc) |
| pr_err("%s: %s: Failed to set pinctrl drive type for clock rate %u (%d)\n", |
| mmc_hostname(host->mmc), __func__, |
| clock, rc); |
| |
| /* |
| * Update the bus vote in case of frequency change due to |
| * clock scaling. |
| */ |
| sdhci_msm_bus_voting(host, 1); |
| } |
| out: |
| sdhci_set_clock(host, clock); |
| } |
| |
| static void sdhci_msm_set_uhs_signaling(struct sdhci_host *host, |
| unsigned int uhs) |
| { |
| struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); |
| struct sdhci_msm_host *msm_host = pltfm_host->priv; |
| const struct sdhci_msm_offset *msm_host_offset = |
| msm_host->offset; |
| u16 ctrl_2; |
| |
| ctrl_2 = sdhci_readw(host, SDHCI_HOST_CONTROL2); |
| /* Select Bus Speed Mode for host */ |
| ctrl_2 &= ~SDHCI_CTRL_UHS_MASK; |
| if ((uhs == MMC_TIMING_MMC_HS400) || |
| (uhs == MMC_TIMING_MMC_HS200) || |
| (uhs == MMC_TIMING_UHS_SDR104)) |
| ctrl_2 |= SDHCI_CTRL_UHS_SDR104; |
| else if (uhs == MMC_TIMING_UHS_SDR12) |
| ctrl_2 |= SDHCI_CTRL_UHS_SDR12; |
| else if (uhs == MMC_TIMING_UHS_SDR25) |
| ctrl_2 |= SDHCI_CTRL_UHS_SDR25; |
| else if (uhs == MMC_TIMING_UHS_SDR50) |
| ctrl_2 |= SDHCI_CTRL_UHS_SDR50; |
| else if ((uhs == MMC_TIMING_UHS_DDR50) || |
| (uhs == MMC_TIMING_MMC_DDR52)) |
| ctrl_2 |= SDHCI_CTRL_UHS_DDR50; |
| /* |
| * When clock frquency is less than 100MHz, the feedback clock must be |
| * provided and DLL must not be used so that tuning can be skipped. To |
| * provide feedback clock, the mode selection can be any value less |
| * than 3'b011 in bits [2:0] of HOST CONTROL2 register. |
| */ |
| if (host->clock <= CORE_FREQ_100MHZ) { |
| if ((uhs == MMC_TIMING_MMC_HS400) || |
| (uhs == MMC_TIMING_MMC_HS200) || |
| (uhs == MMC_TIMING_UHS_SDR104)) |
| ctrl_2 &= ~SDHCI_CTRL_UHS_MASK; |
| |
| /* |
| * Make sure DLL is disabled when not required |
| * |
| * Write 1 to DLL_RST bit of DLL_CONFIG register |
| */ |
| writel_relaxed((readl_relaxed(host->ioaddr + |
| msm_host_offset->CORE_DLL_CONFIG) |
| | CORE_DLL_RST), host->ioaddr + |
| msm_host_offset->CORE_DLL_CONFIG); |
| |
| /* Write 1 to DLL_PDN bit of DLL_CONFIG register */ |
| writel_relaxed((readl_relaxed(host->ioaddr + |
| msm_host_offset->CORE_DLL_CONFIG) |
| | CORE_DLL_PDN), host->ioaddr + |
| msm_host_offset->CORE_DLL_CONFIG); |
| mb(); |
| |
| /* |
| * The DLL needs to be restored and CDCLP533 recalibrated |
| * when the clock frequency is set back to 400MHz. |
| */ |
| msm_host->calibration_done = false; |
| } |
| |
| pr_debug("%s: %s-clock:%u uhs mode:%u ctrl_2:0x%x\n", |
| mmc_hostname(host->mmc), __func__, host->clock, uhs, ctrl_2); |
| sdhci_writew(host, ctrl_2, SDHCI_HOST_CONTROL2); |
| |
| } |
| |
| #define MAX_TEST_BUS 60 |
| #define DRV_NAME "cmdq-host" |
| static void sdhci_msm_cmdq_dump_debug_ram(struct sdhci_host *host) |
| { |
| int i = 0; |
| struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); |
| struct sdhci_msm_host *msm_host = pltfm_host->priv; |
| const struct sdhci_msm_offset *msm_host_offset = |
| msm_host->offset; |
| struct cmdq_host *cq_host = host->cq_host; |
| |
| u32 version = sdhci_msm_readl_relaxed(host, |
| msm_host_offset->CORE_MCI_VERSION); |
| u16 minor = version & CORE_VERSION_TARGET_MASK; |
| /* registers offset changed starting from 4.2.0 */ |
| int offset = minor >= SDHCI_MSM_VER_420 ? 0 : 0x48; |
| |
| if (cq_host->offset_changed) |
| offset += CQ_V5_VENDOR_CFG; |
| pr_err("---- Debug RAM dump ----\n"); |
| pr_err(DRV_NAME ": Debug RAM wrap-around: 0x%08x | Debug RAM overlap: 0x%08x\n", |
| cmdq_readl(cq_host, CQ_CMD_DBG_RAM_WA + offset), |
| cmdq_readl(cq_host, CQ_CMD_DBG_RAM_OL + offset)); |
| |
| while (i < 16) { |
| pr_err(DRV_NAME ": Debug RAM dump [%d]: 0x%08x\n", i, |
| cmdq_readl(cq_host, CQ_CMD_DBG_RAM + offset + (4 * i))); |
| i++; |
| } |
| pr_err("-------------------------\n"); |
| } |
| |
| static void sdhci_msm_cache_debug_data(struct sdhci_host *host) |
| { |
| struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); |
| struct sdhci_msm_host *msm_host = pltfm_host->priv; |
| struct sdhci_msm_debug_data *cached_data = &msm_host->cached_data; |
| |
| memcpy(&cached_data->copy_mmc, msm_host->mmc, |
| sizeof(struct mmc_host)); |
| if (msm_host->mmc->card) |
| memcpy(&cached_data->copy_card, msm_host->mmc->card, |
| sizeof(struct mmc_card)); |
| memcpy(&cached_data->copy_host, host, |
| sizeof(struct sdhci_host)); |
| } |
| |
| void sdhci_msm_dump_vendor_regs(struct sdhci_host *host) |
| { |
| struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); |
| struct sdhci_msm_host *msm_host = pltfm_host->priv; |
| const struct sdhci_msm_offset *msm_host_offset = |
| msm_host->offset; |
| int tbsel, tbsel2; |
| int i, index = 0; |
| u32 test_bus_val = 0; |
| u32 debug_reg[MAX_TEST_BUS] = {0}; |
| u32 sts = 0; |
| |
| sdhci_msm_cache_debug_data(host); |
| pr_info("----------- VENDOR REGISTER DUMP -----------\n"); |
| if (host->cq_host) |
| sdhci_msm_cmdq_dump_debug_ram(host); |
| |
| MMC_TRACE(host->mmc, "Data cnt: 0x%08x | Fifo cnt: 0x%08x\n", |
| sdhci_msm_readl_relaxed(host, |
| msm_host_offset->CORE_MCI_DATA_CNT), |
| sdhci_msm_readl_relaxed(host, |
| msm_host_offset->CORE_MCI_FIFO_CNT)); |
| pr_info("Data cnt: 0x%08x | Fifo cnt: 0x%08x | Int sts: 0x%08x\n", |
| sdhci_msm_readl_relaxed(host, |
| msm_host_offset->CORE_MCI_DATA_CNT), |
| sdhci_msm_readl_relaxed(host, |
| msm_host_offset->CORE_MCI_FIFO_CNT), |
| sdhci_msm_readl_relaxed(host, |
| msm_host_offset->CORE_MCI_STATUS)); |
| pr_info("DLL sts: 0x%08x | DLL cfg: 0x%08x | DLL cfg2: 0x%08x\n", |
| readl_relaxed(host->ioaddr + |
| msm_host_offset->CORE_DLL_STATUS), |
| readl_relaxed(host->ioaddr + |
| msm_host_offset->CORE_DLL_CONFIG), |
| sdhci_msm_readl_relaxed(host, |
| msm_host_offset->CORE_DLL_CONFIG_2)); |
| pr_info("DLL cfg3: 0x%08x | DLL usr ctl: 0x%08x | DDR cfg: 0x%08x\n", |
| readl_relaxed(host->ioaddr + |
| msm_host_offset->CORE_DLL_CONFIG_3), |
| readl_relaxed(host->ioaddr + |
| msm_host_offset->CORE_DLL_USR_CTL), |
| sdhci_msm_readl_relaxed(host, |
| msm_host_offset->CORE_DDR_CONFIG)); |
| pr_info("SDCC ver: 0x%08x | Vndr adma err : addr0: 0x%08x addr1: 0x%08x\n", |
| readl_relaxed(host->ioaddr + |
| msm_host_offset->CORE_MCI_VERSION), |
| readl_relaxed(host->ioaddr + |
| msm_host_offset->CORE_VENDOR_SPEC_ADMA_ERR_ADDR0), |
| readl_relaxed(host->ioaddr + |
| msm_host_offset->CORE_VENDOR_SPEC_ADMA_ERR_ADDR1)); |
| pr_info("Vndr func: 0x%08x | Vndr func2 : 0x%08x Vndr func3: 0x%08x\n", |
| readl_relaxed(host->ioaddr + |
| msm_host_offset->CORE_VENDOR_SPEC), |
| readl_relaxed(host->ioaddr + |
| msm_host_offset->CORE_VENDOR_SPEC_FUNC2), |
| readl_relaxed(host->ioaddr + |
| msm_host_offset->CORE_VENDOR_SPEC3)); |
| /* |
| * tbsel indicates [2:0] bits and tbsel2 indicates [7:4] bits |
| * of CORE_TESTBUS_CONFIG register. |
| * |
| * To select test bus 0 to 7 use tbsel and to select any test bus |
| * above 7 use (tbsel2 | tbsel) to get the test bus number. For eg, |
| * to select test bus 14, write 0x1E to CORE_TESTBUS_CONFIG register |
| * i.e., tbsel2[7:4] = 0001, tbsel[2:0] = 110. |
| */ |
| for (tbsel2 = 0; tbsel2 < 7; tbsel2++) { |
| for (tbsel = 0; tbsel < 8; tbsel++) { |
| if (index >= MAX_TEST_BUS) |
| break; |
| test_bus_val = |
| (tbsel2 << msm_host_offset->CORE_TESTBUS_SEL2_BIT) | |
| tbsel | msm_host_offset->CORE_TESTBUS_ENA; |
| sdhci_msm_writel_relaxed(test_bus_val, host, |
| msm_host_offset->CORE_TESTBUS_CONFIG); |
| debug_reg[index++] = sdhci_msm_readl_relaxed(host, |
| msm_host_offset->CORE_SDCC_DEBUG_REG); |
| } |
| } |
| for (i = 0; i < MAX_TEST_BUS; i = i + 4) |
| pr_info(" Test bus[%d to %d]: 0x%08x 0x%08x 0x%08x 0x%08x\n", |
| i, i + 3, debug_reg[i], debug_reg[i+1], |
| debug_reg[i+2], debug_reg[i+3]); |
| if (host->is_crypto_en) { |
| sdhci_msm_ice_get_status(host, &sts); |
| pr_info("%s: ICE status %x\n", mmc_hostname(host->mmc), sts); |
| sdhci_msm_ice_print_regs(host); |
| } |
| } |
| |
| static void sdhci_msm_reset(struct sdhci_host *host, u8 mask) |
| { |
| struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); |
| struct sdhci_msm_host *msm_host = pltfm_host->priv; |
| |
| /* Set ICE core to be reset in sync with SDHC core */ |
| if (msm_host->ice.pdev) { |
| if (msm_host->ice_hci_support) |
| writel_relaxed(1, host->ioaddr + |
| HC_VENDOR_SPECIFIC_ICE_CTRL); |
| else |
| writel_relaxed(1, |
| host->ioaddr + CORE_VENDOR_SPEC_ICE_CTRL); |
| } |
| |
| sdhci_reset(host, mask); |
| } |
| |
| /* |
| * sdhci_msm_enhanced_strobe_mask :- |
| * Before running CMDQ transfers in HS400 Enhanced Strobe mode, |
| * SW should write 3 to |
| * HC_VENDOR_SPECIFIC_FUNC3.CMDEN_HS400_INPUT_MASK_CNT register. |
| * The default reset value of this register is 2. |
| */ |
| static void sdhci_msm_enhanced_strobe_mask(struct sdhci_host *host, bool set) |
| { |
| struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); |
| struct sdhci_msm_host *msm_host = pltfm_host->priv; |
| const struct sdhci_msm_offset *msm_host_offset = |
| msm_host->offset; |
| |
| if (!msm_host->enhanced_strobe || |
| !mmc_card_strobe(msm_host->mmc->card)) { |
| pr_debug("%s: host/card does not support hs400 enhanced strobe\n", |
| mmc_hostname(host->mmc)); |
| return; |
| } |
| |
| if (set) { |
| writel_relaxed((readl_relaxed(host->ioaddr + |
| msm_host_offset->CORE_VENDOR_SPEC3) |
| | CORE_CMDEN_HS400_INPUT_MASK_CNT), |
| host->ioaddr + msm_host_offset->CORE_VENDOR_SPEC3); |
| } else { |
| writel_relaxed((readl_relaxed(host->ioaddr + |
| msm_host_offset->CORE_VENDOR_SPEC3) |
| & ~CORE_CMDEN_HS400_INPUT_MASK_CNT), |
| host->ioaddr + msm_host_offset->CORE_VENDOR_SPEC3); |
| } |
| } |
| |
| static void sdhci_msm_clear_set_dumpregs(struct sdhci_host *host, bool set) |
| { |
| struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); |
| struct sdhci_msm_host *msm_host = pltfm_host->priv; |
| const struct sdhci_msm_offset *msm_host_offset = |
| msm_host->offset; |
| |
| if (set) { |
| sdhci_msm_writel_relaxed(msm_host_offset->CORE_TESTBUS_ENA, |
| host, msm_host_offset->CORE_TESTBUS_CONFIG); |
| } else { |
| u32 value; |
| |
| value = sdhci_msm_readl_relaxed(host, |
| msm_host_offset->CORE_TESTBUS_CONFIG); |
| value &= ~(msm_host_offset->CORE_TESTBUS_ENA); |
| sdhci_msm_writel_relaxed(value, host, |
| msm_host_offset->CORE_TESTBUS_CONFIG); |
| } |
| } |
| |
| void sdhci_msm_reset_workaround(struct sdhci_host *host, u32 enable) |
| { |
| u32 vendor_func2; |
| unsigned long timeout; |
| struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); |
| struct sdhci_msm_host *msm_host = pltfm_host->priv; |
| const struct sdhci_msm_offset *msm_host_offset = |
| msm_host->offset; |
| |
| vendor_func2 = readl_relaxed(host->ioaddr + |
| msm_host_offset->CORE_VENDOR_SPEC_FUNC2); |
| |
| if (enable) { |
| writel_relaxed(vendor_func2 | HC_SW_RST_REQ, host->ioaddr + |
| msm_host_offset->CORE_VENDOR_SPEC_FUNC2); |
| timeout = 10000; |
| while (readl_relaxed(host->ioaddr + |
| msm_host_offset->CORE_VENDOR_SPEC_FUNC2) & HC_SW_RST_REQ) { |
| if (timeout == 0) { |
| pr_info("%s: Applying wait idle disable workaround\n", |
| mmc_hostname(host->mmc)); |
| /* |
| * Apply the reset workaround to not wait for |
| * pending data transfers on AXI before |
| * resetting the controller. This could be |
| * risky if the transfers were stuck on the |
| * AXI bus. |
| */ |
| vendor_func2 = readl_relaxed(host->ioaddr + |
| msm_host_offset->CORE_VENDOR_SPEC_FUNC2); |
| writel_relaxed(vendor_func2 | |
| HC_SW_RST_WAIT_IDLE_DIS, host->ioaddr + |
| msm_host_offset->CORE_VENDOR_SPEC_FUNC2); |
| host->reset_wa_t = ktime_get(); |
| return; |
| } |
| timeout--; |
| udelay(10); |
| } |
| pr_info("%s: waiting for SW_RST_REQ is successful\n", |
| mmc_hostname(host->mmc)); |
| } else { |
| writel_relaxed(vendor_func2 & ~HC_SW_RST_WAIT_IDLE_DIS, |
| host->ioaddr + msm_host_offset->CORE_VENDOR_SPEC_FUNC2); |
| } |
| } |
| |
| static void sdhci_msm_pm_qos_irq_unvote_work(struct work_struct *work) |
| { |
| struct sdhci_msm_pm_qos_irq *pm_qos_irq = |
| container_of(work, struct sdhci_msm_pm_qos_irq, |
| unvote_work.work); |
| |
| if (atomic_read(&pm_qos_irq->counter)) |
| return; |
| |
| pm_qos_irq->latency = PM_QOS_DEFAULT_VALUE; |
| pm_qos_update_request(&pm_qos_irq->req, pm_qos_irq->latency); |
| } |
| |
| void sdhci_msm_pm_qos_irq_vote(struct sdhci_host *host) |
| { |
| struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); |
| struct sdhci_msm_host *msm_host = pltfm_host->priv; |
| struct sdhci_msm_pm_qos_latency *latency = |
| &msm_host->pdata->pm_qos_data.irq_latency; |
| int counter; |
| |
| if (!msm_host->pm_qos_irq.enabled) |
| return; |
| |
| counter = atomic_inc_return(&msm_host->pm_qos_irq.counter); |
| /* Make sure to update the voting in case power policy has changed */ |
| if (msm_host->pm_qos_irq.latency == latency->latency[host->power_policy] |
| && counter > 1) |
| return; |
| |
| cancel_delayed_work_sync(&msm_host->pm_qos_irq.unvote_work); |
| msm_host->pm_qos_irq.latency = latency->latency[host->power_policy]; |
| pm_qos_update_request(&msm_host->pm_qos_irq.req, |
| msm_host->pm_qos_irq.latency); |
| } |
| |
| void sdhci_msm_pm_qos_irq_unvote(struct sdhci_host *host, bool async) |
| { |
| struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); |
| struct sdhci_msm_host *msm_host = pltfm_host->priv; |
| int counter; |
| |
| if (!msm_host->pm_qos_irq.enabled) |
| return; |
| |
| if (atomic_read(&msm_host->pm_qos_irq.counter)) { |
| counter = atomic_dec_return(&msm_host->pm_qos_irq.counter); |
| } else { |
| WARN(1, "attempt to decrement pm_qos_irq.counter when it's 0"); |
| return; |
| } |
| |
| if (counter) |
| return; |
| |
| if (async) { |
| queue_delayed_work(msm_host->pm_qos_wq, |
| &msm_host->pm_qos_irq.unvote_work, |
| msecs_to_jiffies(QOS_REMOVE_DELAY_MS)); |
| return; |
| } |
| |
| msm_host->pm_qos_irq.latency = PM_QOS_DEFAULT_VALUE; |
| pm_qos_update_request(&msm_host->pm_qos_irq.req, |
| msm_host->pm_qos_irq.latency); |
| } |
| |
| static ssize_t |
| sdhci_msm_pm_qos_irq_show(struct device *dev, |
| struct device_attribute *attr, char *buf) |
| { |
| struct sdhci_host *host = dev_get_drvdata(dev); |
| struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); |
| struct sdhci_msm_host *msm_host = pltfm_host->priv; |
| struct sdhci_msm_pm_qos_irq *irq = &msm_host->pm_qos_irq; |
| |
| return snprintf(buf, PAGE_SIZE, |
| "IRQ PM QoS: enabled=%d, counter=%d, latency=%d\n", |
| irq->enabled, atomic_read(&irq->counter), irq->latency); |
| } |
| |
| static ssize_t |
| sdhci_msm_pm_qos_irq_enable_show(struct device *dev, |
| struct device_attribute *attr, char *buf) |
| { |
| struct sdhci_host *host = dev_get_drvdata(dev); |
| struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); |
| struct sdhci_msm_host *msm_host = pltfm_host->priv; |
| |
| return snprintf(buf, PAGE_SIZE, "%u\n", msm_host->pm_qos_irq.enabled); |
| } |
| |
| static ssize_t |
| sdhci_msm_pm_qos_irq_enable_store(struct device *dev, |
| struct device_attribute *attr, const char *buf, size_t count) |
| { |
| struct sdhci_host *host = dev_get_drvdata(dev); |
| struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); |
| struct sdhci_msm_host *msm_host = pltfm_host->priv; |
| uint32_t value; |
| bool enable; |
| int ret; |
| |
| ret = kstrtou32(buf, 0, &value); |
| if (ret) |
| goto out; |
| enable = !!value; |
| |
| if (enable == msm_host->pm_qos_irq.enabled) |
| goto out; |
| |
| msm_host->pm_qos_irq.enabled = enable; |
| if (!enable) { |
| cancel_delayed_work_sync(&msm_host->pm_qos_irq.unvote_work); |
| atomic_set(&msm_host->pm_qos_irq.counter, 0); |
| msm_host->pm_qos_irq.latency = PM_QOS_DEFAULT_VALUE; |
| pm_qos_update_request(&msm_host->pm_qos_irq.req, |
| msm_host->pm_qos_irq.latency); |
| } |
| |
| out: |
| return count; |
| } |
| |
| #ifdef CONFIG_SMP |
| static inline void set_affine_irq(struct sdhci_msm_host *msm_host, |
| struct sdhci_host *host) |
| { |
| msm_host->pm_qos_irq.req.irq = host->irq; |
| } |
| #else |
| static inline void set_affine_irq(struct sdhci_msm_host *msm_host, |
| struct sdhci_host *host) { } |
| #endif |
| |
| static bool sdhci_msm_pm_qos_wq_init(struct sdhci_msm_host *msm_host) |
| { |
| char *wq = NULL; |
| bool ret = true; |
| |
| wq = kasprintf(GFP_KERNEL, "sdhci_msm_pm_qos/%s", |
| dev_name(&msm_host->pdev->dev)); |
| if (!wq) |
| return false; |
| /* |
| * Create a work queue with flag WQ_MEM_RECLAIM set for |
| * pm_qos_unvote work. Because mmc thread is created with |
| * flag PF_MEMALLOC set, kernel will check for work queue |
| * flag WQ_MEM_RECLAIM when flush the work queue. If work |
| * queue flag WQ_MEM_RECLAIM is not set, kernel warning |
| * will be triggered. |
| */ |
| msm_host->pm_qos_wq = create_workqueue(wq); |
| if (!msm_host->pm_qos_wq) { |
| ret = false; |
| dev_err(&msm_host->pdev->dev, |
| "failed to create pm qos unvote work queue\n"); |
| } |
| kfree(wq); |
| return ret; |
| } |
| |
| void sdhci_msm_pm_qos_irq_init(struct sdhci_host *host) |
| { |
| struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); |
| struct sdhci_msm_host *msm_host = pltfm_host->priv; |
| struct sdhci_msm_pm_qos_latency *irq_latency; |
| int ret; |
| |
| if (!msm_host->pdata->pm_qos_data.irq_valid) |
| return; |
| |
| /* Initialize only once as this gets called per partition */ |
| if (msm_host->pm_qos_irq.enabled) |
| return; |
| |
| atomic_set(&msm_host->pm_qos_irq.counter, 0); |
| msm_host->pm_qos_irq.req.type = |
| msm_host->pdata->pm_qos_data.irq_req_type; |
| if ((msm_host->pm_qos_irq.req.type != PM_QOS_REQ_AFFINE_CORES) && |
| (msm_host->pm_qos_irq.req.type != PM_QOS_REQ_ALL_CORES)) |
| set_affine_irq(msm_host, host); |
| else |
| cpumask_copy(&msm_host->pm_qos_irq.req.cpus_affine, |
| cpumask_of(msm_host->pdata->pm_qos_data.irq_cpu)); |
| |
| sdhci_msm_pm_qos_wq_init(msm_host); |
| |
| INIT_DELAYED_WORK(&msm_host->pm_qos_irq.unvote_work, |
| sdhci_msm_pm_qos_irq_unvote_work); |
| /* For initialization phase, set the performance latency */ |
| irq_latency = &msm_host->pdata->pm_qos_data.irq_latency; |
| msm_host->pm_qos_irq.latency = |
| irq_latency->latency[SDHCI_PERFORMANCE_MODE]; |
| pm_qos_add_request(&msm_host->pm_qos_irq.req, PM_QOS_CPU_DMA_LATENCY, |
| msm_host->pm_qos_irq.latency); |
| msm_host->pm_qos_irq.enabled = true; |
| |
| /* sysfs */ |
| msm_host->pm_qos_irq.enable_attr.show = |
| sdhci_msm_pm_qos_irq_enable_show; |
| msm_host->pm_qos_irq.enable_attr.store = |
| sdhci_msm_pm_qos_irq_enable_store; |
| sysfs_attr_init(&msm_host->pm_qos_irq.enable_attr.attr); |
| msm_host->pm_qos_irq.enable_attr.attr.name = "pm_qos_irq_enable"; |
| msm_host->pm_qos_irq.enable_attr.attr.mode = S_IRUGO | S_IWUSR; |
| ret = device_create_file(&msm_host->pdev->dev, |
| &msm_host->pm_qos_irq.enable_attr); |
| if (ret) |
| pr_err("%s: fail to create pm_qos_irq_enable (%d)\n", |
| __func__, ret); |
| |
| msm_host->pm_qos_irq.status_attr.show = sdhci_msm_pm_qos_irq_show; |
| msm_host->pm_qos_irq.status_attr.store = NULL; |
| sysfs_attr_init(&msm_host->pm_qos_irq.status_attr.attr); |
| msm_host->pm_qos_irq.status_attr.attr.name = "pm_qos_irq_status"; |
| msm_host->pm_qos_irq.status_attr.attr.mode = S_IRUGO; |
| ret = device_create_file(&msm_host->pdev->dev, |
| &msm_host->pm_qos_irq.status_attr); |
| if (ret) |
| pr_err("%s: fail to create pm_qos_irq_status (%d)\n", |
| __func__, ret); |
| } |
| |
| static ssize_t sdhci_msm_pm_qos_group_show(struct device *dev, |
| struct device_attribute *attr, char *buf) |
| { |
| struct sdhci_host *host = dev_get_drvdata(dev); |
| struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); |
| struct sdhci_msm_host *msm_host = pltfm_host->priv; |
| struct sdhci_msm_pm_qos_group *group; |
| int i; |
| int nr_groups = msm_host->pdata->pm_qos_data.cpu_group_map.nr_groups; |
| int offset = 0; |
| |
| for (i = 0; i < nr_groups; i++) { |
| group = &msm_host->pm_qos[i]; |
| offset += snprintf(&buf[offset], PAGE_SIZE, |
| "Group #%d (mask=0x%lx) PM QoS: enabled=%d, counter=%d, latency=%d\n", |
| i, group->req.cpus_affine.bits[0], |
| msm_host->pm_qos_group_enable, |
| atomic_read(&group->counter), |
| group->latency); |
| } |
| |
| return offset; |
| } |
| |
| static ssize_t sdhci_msm_pm_qos_group_enable_show(struct device *dev, |
| struct device_attribute *attr, char *buf) |
| { |
| struct sdhci_host *host = dev_get_drvdata(dev); |
| struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); |
| struct sdhci_msm_host *msm_host = pltfm_host->priv; |
| |
| return snprintf(buf, PAGE_SIZE, "%s\n", |
| msm_host->pm_qos_group_enable ? "enabled" : "disabled"); |
| } |
| |
| static ssize_t sdhci_msm_pm_qos_group_enable_store(struct device *dev, |
| struct device_attribute *attr, const char *buf, size_t count) |
| { |
| struct sdhci_host *host = dev_get_drvdata(dev); |
| struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); |
| struct sdhci_msm_host *msm_host = pltfm_host->priv; |
| int nr_groups = msm_host->pdata->pm_qos_data.cpu_group_map.nr_groups; |
| uint32_t value; |
| bool enable; |
| int ret; |
| int i; |
| |
| ret = kstrtou32(buf, 0, &value); |
| if (ret) |
| goto out; |
| enable = !!value; |
| |
| if (enable == msm_host->pm_qos_group_enable) |
| goto out; |
| |
| msm_host->pm_qos_group_enable = enable; |
| if (!enable) { |
| for (i = 0; i < nr_groups; i++) { |
| cancel_delayed_work_sync( |
| &msm_host->pm_qos[i].unvote_work); |
| atomic_set(&msm_host->pm_qos[i].counter, 0); |
| msm_host->pm_qos[i].latency = PM_QOS_DEFAULT_VALUE; |
| pm_qos_update_request(&msm_host->pm_qos[i].req, |
| msm_host->pm_qos[i].latency); |
| } |
| } |
| |
| out: |
| return count; |
| } |
| |
| static int sdhci_msm_get_cpu_group(struct sdhci_msm_host *msm_host, int cpu) |
| { |
| int i; |
| struct sdhci_msm_cpu_group_map *map = |
| &msm_host->pdata->pm_qos_data.cpu_group_map; |
| |
| if (cpu < 0) |
| goto not_found; |
| |
| for (i = 0; i < map->nr_groups; i++) |
| if (cpumask_test_cpu(cpu, &map->mask[i])) |
| return i; |
| |
| not_found: |
| return -EINVAL; |
| } |
| |
| void sdhci_msm_pm_qos_cpu_vote(struct sdhci_host *host, |
| struct sdhci_msm_pm_qos_latency *latency, int cpu) |
| { |
| struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); |
| struct sdhci_msm_host *msm_host = pltfm_host->priv; |
| int group = sdhci_msm_get_cpu_group(msm_host, cpu); |
| struct sdhci_msm_pm_qos_group *pm_qos_group; |
| int counter; |
| |
| if (!msm_host->pm_qos_group_enable || group < 0) |
| return; |
| |
| pm_qos_group = &msm_host->pm_qos[group]; |
| counter = atomic_inc_return(&pm_qos_group->counter); |
| |
| /* Make sure to update the voting in case power policy has changed */ |
| if (pm_qos_group->latency == latency->latency[host->power_policy] |
| && counter > 1) |
| return; |
| |
| cancel_delayed_work_sync(&pm_qos_group->unvote_work); |
| |
| pm_qos_group->latency = latency->latency[host->power_policy]; |
| pm_qos_update_request(&pm_qos_group->req, pm_qos_group->latency); |
| } |
| |
| static void sdhci_msm_pm_qos_cpu_unvote_work(struct work_struct *work) |
| { |
| struct sdhci_msm_pm_qos_group *group = |
| container_of(work, struct sdhci_msm_pm_qos_group, |
| unvote_work.work); |
| |
| if (atomic_read(&group->counter)) |
| return; |
| |
| group->latency = PM_QOS_DEFAULT_VALUE; |
| pm_qos_update_request(&group->req, group->latency); |
| } |
| |
| bool sdhci_msm_pm_qos_cpu_unvote(struct sdhci_host *host, int cpu, bool async) |
| { |
| struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); |
| struct sdhci_msm_host *msm_host = pltfm_host->priv; |
| int group = sdhci_msm_get_cpu_group(msm_host, cpu); |
| |
| if (!msm_host->pm_qos_group_enable || group < 0 || |
| atomic_dec_return(&msm_host->pm_qos[group].counter)) |
| return false; |
| |
| if (async) { |
| queue_delayed_work(msm_host->pm_qos_wq, |
| &msm_host->pm_qos[group].unvote_work, |
| msecs_to_jiffies(QOS_REMOVE_DELAY_MS)); |
| return true; |
| } |
| |
| msm_host->pm_qos[group].latency = PM_QOS_DEFAULT_VALUE; |
| pm_qos_update_request(&msm_host->pm_qos[group].req, |
| msm_host->pm_qos[group].latency); |
| return true; |
| } |
| |
| void sdhci_msm_pm_qos_cpu_init(struct sdhci_host *host, |
| struct sdhci_msm_pm_qos_latency *latency) |
| { |
| struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); |
| struct sdhci_msm_host *msm_host = pltfm_host->priv; |
| int nr_groups = msm_host->pdata->pm_qos_data.cpu_group_map.nr_groups; |
| struct sdhci_msm_pm_qos_group *group; |
| int i; |
| int ret; |
| |
| if (msm_host->pm_qos_group_enable) |
| return; |
| |
| msm_host->pm_qos = kcalloc(nr_groups, sizeof(*msm_host->pm_qos), |
| GFP_KERNEL); |
| if (!msm_host->pm_qos) |
| return; |
| |
| for (i = 0; i < nr_groups; i++) { |
| group = &msm_host->pm_qos[i]; |
| INIT_DELAYED_WORK(&group->unvote_work, |
| sdhci_msm_pm_qos_cpu_unvote_work); |
| atomic_set(&group->counter, 0); |
| group->req.type = PM_QOS_REQ_AFFINE_CORES; |
| cpumask_copy(&group->req.cpus_affine, |
| &msm_host->pdata->pm_qos_data.cpu_group_map.mask[i]); |
| /* We set default latency here for all pm_qos cpu groups. */ |
| group->latency = PM_QOS_DEFAULT_VALUE; |
| pm_qos_add_request(&group->req, PM_QOS_CPU_DMA_LATENCY, |
| group->latency); |
| pr_info("%s (): voted for group #%d (mask=0x%lx) latency=%d\n", |
| __func__, i, |
| group->req.cpus_affine.bits[0], |
| group->latency); |
| } |
| msm_host->pm_qos_prev_cpu = -1; |
| msm_host->pm_qos_group_enable = true; |
| |
| /* sysfs */ |
| msm_host->pm_qos_group_status_attr.show = sdhci_msm_pm_qos_group_show; |
| msm_host->pm_qos_group_status_attr.store = NULL; |
| sysfs_attr_init(&msm_host->pm_qos_group_status_attr.attr); |
| msm_host->pm_qos_group_status_attr.attr.name = |
| "pm_qos_cpu_groups_status"; |
| msm_host->pm_qos_group_status_attr.attr.mode = S_IRUGO; |
| ret = device_create_file(&msm_host->pdev->dev, |
| &msm_host->pm_qos_group_status_attr); |
| if (ret) |
| dev_err(&msm_host->pdev->dev, "%s: fail to create pm_qos_group_status_attr (%d)\n", |
| __func__, ret); |
| msm_host->pm_qos_group_enable_attr.show = |
| sdhci_msm_pm_qos_group_enable_show; |
| msm_host->pm_qos_group_enable_attr.store = |
| sdhci_msm_pm_qos_group_enable_store; |
| sysfs_attr_init(&msm_host->pm_qos_group_enable_attr.attr); |
| msm_host->pm_qos_group_enable_attr.attr.name = |
| "pm_qos_cpu_groups_enable"; |
| msm_host->pm_qos_group_enable_attr.attr.mode = S_IRUGO; |
| ret = device_create_file(&msm_host->pdev->dev, |
| &msm_host->pm_qos_group_enable_attr); |
| if (ret) |
| dev_err(&msm_host->pdev->dev, "%s: fail to create pm_qos_group_enable_attr (%d)\n", |
| __func__, ret); |
| } |
| |
| static void sdhci_msm_pre_req(struct sdhci_host *host, |
| struct mmc_request *mmc_req) |
| { |
| int cpu; |
| int group; |
| struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); |
| struct sdhci_msm_host *msm_host = pltfm_host->priv; |
| int prev_group = sdhci_msm_get_cpu_group(msm_host, |
| msm_host->pm_qos_prev_cpu); |
| |
| sdhci_msm_pm_qos_irq_vote(host); |
| |
| cpu = get_cpu(); |
| put_cpu(); |
| group = sdhci_msm_get_cpu_group(msm_host, cpu); |
| if (group < 0) |
| return; |
| |
| if (group != prev_group && prev_group >= 0) { |
| sdhci_msm_pm_qos_cpu_unvote(host, |
| msm_host->pm_qos_prev_cpu, false); |
| prev_group = -1; /* make sure to vote for new group */ |
| } |
| |
| if (prev_group < 0) { |
| sdhci_msm_pm_qos_cpu_vote(host, |
| msm_host->pdata->pm_qos_data.latency, cpu); |
| msm_host->pm_qos_prev_cpu = cpu; |
| } |
| } |
| |
| static void sdhci_msm_post_req(struct sdhci_host *host, |
| struct mmc_request *mmc_req) |
| { |
| struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); |
| struct sdhci_msm_host *msm_host = pltfm_host->priv; |
| |
| sdhci_msm_pm_qos_irq_unvote(host, false); |
| |
| if (sdhci_msm_pm_qos_cpu_unvote(host, msm_host->pm_qos_prev_cpu, false)) |
| msm_host->pm_qos_prev_cpu = -1; |
| } |
| |
| static void sdhci_msm_init(struct sdhci_host *host) |
| { |
| struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); |
| struct sdhci_msm_host *msm_host = pltfm_host->priv; |
| |
| sdhci_msm_pm_qos_irq_init(host); |
| |
| if (msm_host->pdata->pm_qos_data.legacy_valid) |
| sdhci_msm_pm_qos_cpu_init(host, |
| msm_host->pdata->pm_qos_data.latency); |
| } |
| |
| static unsigned int sdhci_msm_get_current_limit(struct sdhci_host *host) |
| { |
| struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); |
| struct sdhci_msm_host *msm_host = pltfm_host->priv; |
| struct sdhci_msm_slot_reg_data *curr_slot = msm_host->pdata->vreg_data; |
| u32 max_curr = 0; |
| |
| if (curr_slot && curr_slot->vdd_data) |
| max_curr = curr_slot->vdd_data->hpm_uA; |
| |
| return max_curr; |
| } |
| |
| static int sdhci_msm_notify_load(struct sdhci_host *host, enum mmc_load state) |
| { |
| struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); |
| struct sdhci_msm_host *msm_host = pltfm_host->priv; |
| int ret = 0; |
| u32 clk_rate = 0; |
| |
| if (!IS_ERR(msm_host->ice_clk)) { |
| clk_rate = (state == MMC_LOAD_LOW) ? |
| msm_host->pdata->ice_clk_min : |
| msm_host->pdata->ice_clk_max; |
| if (msm_host->ice_clk_rate == clk_rate) |
| return 0; |
| pr_debug("%s: changing ICE clk rate to %u\n", |
| mmc_hostname(host->mmc), clk_rate); |
| ret = clk_set_rate(msm_host->ice_clk, clk_rate); |
| if (ret) { |
| pr_err("%s: ICE_CLK rate set failed (%d) for %u\n", |
| mmc_hostname(host->mmc), ret, clk_rate); |
| return ret; |
| } |
| msm_host->ice_clk_rate = clk_rate; |
| } |
| return 0; |
| } |
| |
| static struct sdhci_ops sdhci_msm_ops = { |
| .crypto_engine_cfg = sdhci_msm_ice_cfg, |
| .crypto_engine_cmdq_cfg = sdhci_msm_ice_cmdq_cfg, |
| .crypto_engine_cfg_end = sdhci_msm_ice_cfg_end, |
| .crypto_cfg_reset = sdhci_msm_ice_cfg_reset, |
| .crypto_engine_reset = sdhci_msm_ice_reset, |
| .set_uhs_signaling = sdhci_msm_set_uhs_signaling, |
| .check_power_status = sdhci_msm_check_power_status, |
| .platform_execute_tuning = sdhci_msm_execute_tuning, |
| .enhanced_strobe = sdhci_msm_enhanced_strobe, |
| .toggle_cdr = sdhci_msm_toggle_cdr, |
| .get_max_segments = sdhci_msm_max_segs, |
| .set_clock = sdhci_msm_set_clock, |
| .get_min_clock = sdhci_msm_get_min_clock, |
| .get_max_clock = sdhci_msm_get_max_clock, |
| .dump_vendor_regs = sdhci_msm_dump_vendor_regs, |
| .config_auto_tuning_cmd = sdhci_msm_config_auto_tuning_cmd, |
| .enable_controller_clock = sdhci_msm_enable_controller_clock, |
| .set_bus_width = sdhci_set_bus_width, |
| .reset = sdhci_msm_reset, |
| .clear_set_dumpregs = sdhci_msm_clear_set_dumpregs, |
| .enhanced_strobe_mask = sdhci_msm_enhanced_strobe_mask, |
| .reset_workaround = sdhci_msm_reset_workaround, |
| .init = sdhci_msm_init, |
| .pre_req = sdhci_msm_pre_req, |
| .post_req = sdhci_msm_post_req, |
| .get_current_limit = sdhci_msm_get_current_limit, |
| .notify_load = sdhci_msm_notify_load, |
| }; |
| |
| static void sdhci_set_default_hw_caps(struct sdhci_msm_host *msm_host, |
| struct sdhci_host *host) |
| { |
| u32 version, caps = 0; |
| u16 minor; |
| u8 major; |
| u32 val; |
| const struct sdhci_msm_offset *msm_host_offset = |
| msm_host->offset; |
| |
| version = sdhci_msm_readl_relaxed(host, |
| msm_host_offset->CORE_MCI_VERSION); |
| major = (version & CORE_VERSION_MAJOR_MASK) >> |
| CORE_VERSION_MAJOR_SHIFT; |
| minor = version & CORE_VERSION_TARGET_MASK; |
| |
| caps = readl_relaxed(host->ioaddr + SDHCI_CAPABILITIES); |
| |
| /* |
| * Starting with SDCC 5 controller (core major version = 1) |
| * controller won't advertise 3.0v, 1.8v and 8-bit features |
| * except for some targets. |
| */ |
| if (major >= 1 && minor != 0x11 && minor != 0x12) { |
| struct sdhci_msm_reg_data *vdd_io_reg; |
| /* |
| * Enable 1.8V support capability on controllers that |
| * support dual voltage |
| */ |
| vdd_io_reg = msm_host->pdata->vreg_data->vdd_io_data; |
| if (vdd_io_reg && (vdd_io_reg->high_vol_level > 2700000)) |
| caps |= CORE_3_0V_SUPPORT; |
| if (vdd_io_reg && (vdd_io_reg->low_vol_level < 1950000)) |
| caps |= CORE_1_8V_SUPPORT; |
| if (msm_host->pdata->mmc_bus_width == MMC_CAP_8_BIT_DATA) |
| caps |= CORE_8_BIT_SUPPORT; |
| } |
| |
| /* |
| * Enable one MID mode for SDCC5 (major 1) on 8916/8939 (minor 0x2e) and |
| * on 8992 (minor 0x3e) as a workaround to reset for data stuck issue. |
| */ |
| if (major == 1 && (minor == 0x2e || minor == 0x3e)) { |
| host->quirks2 |= SDHCI_QUIRK2_USE_RESET_WORKAROUND; |
| val = readl_relaxed(host->ioaddr + |
| msm_host_offset->CORE_VENDOR_SPEC_FUNC2); |
| writel_relaxed((val | CORE_ONE_MID_EN), |
| host->ioaddr + msm_host_offset->CORE_VENDOR_SPEC_FUNC2); |
| } |
| /* |
| * SDCC 5 controller with major version 1, minor version 0x34 and later |
| * with HS 400 mode support will use CM DLL instead of CDC LP 533 DLL. |
| */ |
| if ((major == 1) && (minor < 0x34)) |
| msm_host->use_cdclp533 = true; |
| |
| /* |
| * SDCC 5 controller with major version 1, minor version 0x42 and later |
| * will require additional steps when resetting DLL. |
| * It also supports HS400 enhanced strobe mode. |
| */ |
| if ((major == 1) && (minor >= 0x42)) { |
| msm_host->use_updated_dll_reset = true; |
| msm_host->enhanced_strobe = true; |
| } |
| |
| /* |
| * SDCC 5 controller with major version 1 and minor version 0x42, |
| * 0x46 and 0x49 currently uses 14lpp tech DLL whose internal |
| * gating cannot guarantee MCLK timing requirement i.e. |
| * when MCLK is gated OFF, it is not gated for less than 0.5us |
| * and MCLK must be switched on for at-least 1us before DATA |
| * starts coming. |
| */ |
| if ((major == 1) && ((minor == 0x42) || (minor == 0x46) || |
| (minor == 0x49) || (minor == 0x4D) || (minor >= 0x6b))) |
| msm_host->use_14lpp_dll = true; |
| |
| /* Fake 3.0V support for SDIO devices which requires such voltage */ |
| if (msm_host->core_3_0v_support) { |
| caps |= CORE_3_0V_SUPPORT; |
| writel_relaxed((readl_relaxed(host->ioaddr + |
| SDHCI_CAPABILITIES) | caps), host->ioaddr + |
| msm_host_offset->CORE_VENDOR_SPEC_CAPABILITIES0); |
| } |
| |
| if ((major == 1) && (minor >= 0x49)) |
| msm_host->rclk_delay_fix = true; |
| /* |
| * Mask 64-bit support for controller with 32-bit address bus so that |
| * smaller descriptor size will be used and improve memory consumption. |
| */ |
| if (!msm_host->pdata->largeaddressbus) |
| caps &= ~CORE_SYS_BUS_SUPPORT_64_BIT; |
| |
| writel_relaxed(caps, host->ioaddr + |
| msm_host_offset->CORE_VENDOR_SPEC_CAPABILITIES0); |
| /* keep track of the value in SDHCI_CAPABILITIES */ |
| msm_host->caps_0 = caps; |
| |
| if ((major == 1) && (minor >= 0x6b)) { |
| msm_host->ice_hci_support = true; |
| host->cdr_support = true; |
| } |
| |
| if ((major == 1) && (minor >= 0x71)) |
| msm_host->need_dll_user_ctl = true; |
| |
| } |
| |
| #ifdef CONFIG_MMC_CQ_HCI |
| static void sdhci_msm_cmdq_init(struct sdhci_host *host, |
| struct platform_device *pdev) |
| { |
| struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); |
| struct sdhci_msm_host *msm_host = pltfm_host->priv; |
| |
| if (nocmdq) { |
| dev_dbg(&pdev->dev, "CMDQ disabled via cmdline\n"); |
| return; |
| } |
| |
| host->cq_host = cmdq_pltfm_init(pdev); |
| if (IS_ERR(host->cq_host)) { |
| dev_dbg(&pdev->dev, "cmdq-pltfm init: failed: %ld\n", |
| PTR_ERR(host->cq_host)); |
| host->cq_host = NULL; |
| } else { |
| msm_host->mmc->caps2 |= MMC_CAP2_CMD_QUEUE; |
| } |
| } |
| #else |
| static void sdhci_msm_cmdq_init(struct sdhci_host *host, |
| struct platform_device *pdev) |
| { |
| |
| } |
| #endif |
| |
| static bool sdhci_msm_is_bootdevice(struct device *dev) |
| { |
| if (strnstr(saved_command_line, "androidboot.bootdevice=", |
| strlen(saved_command_line))) { |
| char search_string[50]; |
| |
| snprintf(search_string, ARRAY_SIZE(search_string), |
| "androidboot.bootdevice=%s", dev_name(dev)); |
| if (strnstr(saved_command_line, search_string, |
| strlen(saved_command_line))) |
| return true; |
| else |
| return false; |
| } |
| |
| /* |
| * "androidboot.bootdevice=" argument is not present then |
| * return true as we don't know the boot device anyways. |
| */ |
| return true; |
| } |
| |
| static int sdhci_msm_probe(struct platform_device *pdev) |
| { |
| const struct sdhci_msm_offset *msm_host_offset; |
| struct sdhci_host *host; |
| struct sdhci_pltfm_host *pltfm_host; |
| struct sdhci_msm_host *msm_host; |
| struct resource *core_memres = NULL; |
| int ret = 0, dead = 0; |
| u16 host_version; |
| u32 irq_status, irq_ctl; |
| struct resource *tlmm_memres = NULL; |
| void __iomem *tlmm_mem; |
| unsigned long flags; |
| bool force_probe; |
| |
| pr_debug("%s: Enter %s\n", dev_name(&pdev->dev), __func__); |
| msm_host = devm_kzalloc(&pdev->dev, sizeof(struct sdhci_msm_host), |
| GFP_KERNEL); |
| if (!msm_host) { |
| ret = -ENOMEM; |
| goto out; |
| } |
| |
| if (of_find_compatible_node(NULL, NULL, "qcom,sdhci-msm-v5")) { |
| msm_host->mci_removed = true; |
| msm_host->offset = &sdhci_msm_offset_mci_removed; |
| } else { |
| msm_host->mci_removed = false; |
| msm_host->offset = &sdhci_msm_offset_mci_present; |
| } |
| msm_host_offset = msm_host->offset; |
| msm_host->sdhci_msm_pdata.ops = &sdhci_msm_ops; |
| host = sdhci_pltfm_init(pdev, &msm_host->sdhci_msm_pdata, 0); |
| if (IS_ERR(host)) { |
| ret = PTR_ERR(host); |
| goto out_host_free; |
| } |
| |
| pltfm_host = sdhci_priv(host); |
| pltfm_host->priv = msm_host; |
| msm_host->mmc = host->mmc; |
| msm_host->pdev = pdev; |
| |
| ret = sdhci_msm_get_socrev(&pdev->dev, msm_host); |
| if (ret == -EPROBE_DEFER) { |
| dev_err(&pdev->dev, "SoC version rd: fail: defer for now\n"); |
| goto pltfm_free; |
| } |
| |
| /* get the ice device vops if present */ |
| ret = sdhci_msm_ice_get_dev(host); |
| if (ret == -EPROBE_DEFER) { |
| /* |
| * SDHCI driver might be probed before ICE driver does. |
| * In that case we would like to return EPROBE_DEFER code |
| * in order to delay its probing. |
| */ |
| dev_err(&pdev->dev, "%s: required ICE device not probed yet err = %d\n", |
| __func__, ret); |
| goto pltfm_free; |
| |
| } else if (ret == -ENODEV) { |
| /* |
| * ICE device is not enabled in DTS file. No need for further |
| * initialization of ICE driver. |
| */ |
| dev_warn(&pdev->dev, "%s: ICE device is not enabled", |
| __func__); |
| } else if (ret) { |
| dev_err(&pdev->dev, "%s: sdhci_msm_ice_get_dev failed %d\n", |
| __func__, ret); |
| goto pltfm_free; |
| } |
| |
| /* Extract platform data */ |
| if (pdev->dev.of_node) { |
| ret = of_alias_get_id(pdev->dev.of_node, "sdhc"); |
| if (ret <= 0) { |
| dev_err(&pdev->dev, "Failed to get slot index %d\n", |
| ret); |
| goto pltfm_free; |
| } |
| |
| /* Read property to determine if the probe is forced */ |
| force_probe = of_find_property(pdev->dev.of_node, |
| "qcom,force-sdhc1-probe", NULL); |
| |
| /* skip the probe if eMMC isn't a boot device */ |
| if ((ret == 1) && !sdhci_msm_is_bootdevice(&pdev->dev) |
| && !force_probe) { |
| ret = -ENODEV; |
| goto pltfm_free; |
| } |
| |
| if (disable_slots & (1 << (ret - 1))) { |
| dev_info(&pdev->dev, "%s: Slot %d disabled\n", __func__, |
| ret); |
| ret = -ENODEV; |
| goto pltfm_free; |
| } |
| |
| if (ret <= 2) |
| sdhci_slot[ret-1] = msm_host; |
| |
| msm_host->pdata = sdhci_msm_populate_pdata(&pdev->dev, |
| msm_host); |
| if (!msm_host->pdata) { |
| dev_err(&pdev->dev, "DT parsing error\n"); |
| goto pltfm_free; |
| } |
| } else { |
| dev_err(&pdev->dev, "No device tree node\n"); |
| goto pltfm_free; |
| } |
| |
| /* Setup Clocks */ |
| |
| /* Setup SDCC bus voter clock. */ |
| msm_host->bus_clk = devm_clk_get(&pdev->dev, "bus_clk"); |
| if (!IS_ERR_OR_NULL(msm_host->bus_clk)) { |
| /* Vote for max. clk rate for max. performance */ |
| ret = clk_set_rate(msm_host->bus_clk, INT_MAX); |
| if (ret) |
| goto pltfm_free; |
| ret = clk_prepare_enable(msm_host->bus_clk); |
| if (ret) |
| goto pltfm_free; |
| } |
| |
| /* Setup main peripheral bus clock */ |
| msm_host->pclk = devm_clk_get(&pdev->dev, "iface_clk"); |
| if (!IS_ERR(msm_host->pclk)) { |
| ret = clk_prepare_enable(msm_host->pclk); |
| if (ret) |
| goto bus_clk_disable; |
| } |
| atomic_set(&msm_host->controller_clock, 1); |
| |
| /* Setup SDC ufs bus aggr clock */ |
| msm_host->bus_aggr_clk = devm_clk_get(&pdev->dev, "bus_aggr_clk"); |
| if (!IS_ERR(msm_host->bus_aggr_clk)) { |
| ret = clk_prepare_enable(msm_host->bus_aggr_clk); |
| if (ret) { |
| dev_err(&pdev->dev, "Bus aggregate clk not enabled\n"); |
| goto pclk_disable; |
| } |
| } |
| |
| if (msm_host->ice.pdev) { |
| /* Setup SDC ICE clock */ |
| msm_host->ice_clk = devm_clk_get(&pdev->dev, "ice_core_clk"); |
| if (!IS_ERR(msm_host->ice_clk)) { |
| /* ICE core has only one clock frequency for now */ |
| ret = clk_set_rate(msm_host->ice_clk, |
| msm_host->pdata->ice_clk_max); |
| if (ret) { |
| dev_err(&pdev->dev, "ICE_CLK rate set failed (%d) for %u\n", |
| ret, |
| msm_host->pdata->ice_clk_max); |
| goto bus_aggr_clk_disable; |
| } |
| ret = clk_prepare_enable(msm_host->ice_clk); |
| if (ret) |
| goto bus_aggr_clk_disable; |
| |
| msm_host->ice_clk_rate = |
| msm_host->pdata->ice_clk_max; |
| } |
| } |
| |
| /* Setup SDC MMC clock */ |
| msm_host->clk = devm_clk_get(&pdev->dev, "core_clk"); |
| if (IS_ERR(msm_host->clk)) { |
| ret = PTR_ERR(msm_host->clk); |
| goto bus_aggr_clk_disable; |
| } |
| |
| /* Set to the minimum supported clock frequency */ |
| ret = clk_set_rate(msm_host->clk, sdhci_msm_get_min_clock(host)); |
| if (ret) { |
| dev_err(&pdev->dev, "MClk rate set failed (%d)\n", ret); |
| goto bus_aggr_clk_disable; |
| } |
| ret = clk_prepare_enable(msm_host->clk); |
| if (ret) |
| goto bus_aggr_clk_disable; |
| |
| msm_host->clk_rate = sdhci_msm_get_min_clock(host); |
| atomic_set(&msm_host->clks_on, 1); |
| |
| /* Setup CDC calibration fixed feedback clock */ |
| msm_host->ff_clk = devm_clk_get(&pdev->dev, "cal_clk"); |
| if (!IS_ERR(msm_host->ff_clk)) { |
| ret = clk_prepare_enable(msm_host->ff_clk); |
| if (ret) |
| goto clk_disable; |
| } |
| |
| /* Setup CDC calibration sleep clock */ |
| msm_host->sleep_clk = devm_clk_get(&pdev->dev, "sleep_clk"); |
| if (!IS_ERR(msm_host->sleep_clk)) { |
| ret = clk_prepare_enable(msm_host->sleep_clk); |
| if (ret) |
| goto ff_clk_disable; |
| } |
| |
| msm_host->saved_tuning_phase = INVALID_TUNING_PHASE; |
| |
| ret = sdhci_msm_bus_register(msm_host, pdev); |
| if (ret) |
| goto sleep_clk_disable; |
| |
| if (msm_host->msm_bus_vote.client_handle) |
| INIT_DELAYED_WORK(&msm_host->msm_bus_vote.vote_work, |
| sdhci_msm_bus_work); |
| sdhci_msm_bus_voting(host, 1); |
| |
| /* Setup regulators */ |
| ret = sdhci_msm_vreg_init(&pdev->dev, msm_host->pdata, true); |
| if (ret) { |
| dev_err(&pdev->dev, "Regulator setup failed (%d)\n", ret); |
| goto bus_unregister; |
| } |
| |
| /* Reset the core and Enable SDHC mode */ |
| core_memres = platform_get_resource_byname(pdev, |
| IORESOURCE_MEM, "core_mem"); |
| if (!msm_host->mci_removed) { |
| if (!core_memres) { |
| dev_err(&pdev->dev, "Failed to get iomem resource\n"); |
| goto vreg_deinit; |
| } |
| msm_host->core_mem = devm_ioremap(&pdev->dev, |
| core_memres->start, resource_size(core_memres)); |
| |
| if (!msm_host->core_mem) { |
| dev_err(&pdev->dev, "Failed to remap registers\n"); |
| ret = -ENOMEM; |
| goto vreg_deinit; |
| } |
| } |
| |
| tlmm_memres = platform_get_resource_byname(pdev, |
| IORESOURCE_MEM, "tlmm_mem"); |
| if (tlmm_memres) { |
| tlmm_mem = devm_ioremap(&pdev->dev, tlmm_memres->start, |
| resource_size(tlmm_memres)); |
| |
| if (!tlmm_mem) { |
| dev_err(&pdev->dev, "Failed to remap tlmm registers\n"); |
| ret = -ENOMEM; |
| goto vreg_deinit; |
| } |
| writel_relaxed(readl_relaxed(tlmm_mem) | 0x2, tlmm_mem); |
| } |
| |
| /* |
| * Reset the vendor spec register to power on reset state. |
| */ |
| writel_relaxed(CORE_VENDOR_SPEC_POR_VAL, |
| host->ioaddr + msm_host_offset->CORE_VENDOR_SPEC); |
| |
| /* This enable ADMA error interrupt in case of length mismatch */ |
| writel_relaxed((readl_relaxed(host->ioaddr + |
| msm_host_offset->CORE_VENDOR_SPEC) | |
| CORE_VNDR_SPEC_ADMA_ERR_SIZE_EN), |
| host->ioaddr + msm_host_offset->CORE_VENDOR_SPEC); |
| |
| /* |
| * Ensure SDHCI FIFO is enabled by disabling alternative FIFO |
| */ |
| writel_relaxed((readl_relaxed(host->ioaddr + |
| msm_host_offset->CORE_VENDOR_SPEC3) & |
| ~CORE_FIFO_ALT_EN), host->ioaddr + |
| msm_host_offset->CORE_VENDOR_SPEC3); |
| |
| if (!msm_host->mci_removed) { |
| /* Set HC_MODE_EN bit in HC_MODE register */ |
| writel_relaxed(HC_MODE_EN, (msm_host->core_mem + CORE_HC_MODE)); |
| |
| /* Set FF_CLK_SW_RST_DIS bit in HC_MODE register */ |
| writel_relaxed(readl_relaxed(msm_host->core_mem + |
| CORE_HC_MODE) | FF_CLK_SW_RST_DIS, |
| msm_host->core_mem + CORE_HC_MODE); |
| } |
| sdhci_set_default_hw_caps(msm_host, host); |
| |
| /* |
| * Set the PAD_PWR_SWITCH_EN bit so that the PAD_PWR_SWITCH bit can |
| * be used as required later on. |
| */ |
| writel_relaxed((readl_relaxed(host->ioaddr + |
| msm_host_offset->CORE_VENDOR_SPEC) | |
| CORE_IO_PAD_PWR_SWITCH_EN), host->ioaddr + |
| msm_host_offset->CORE_VENDOR_SPEC); |
| /* |
| * CORE_SW_RST above may trigger power irq if previous status of PWRCTL |
| * was either BUS_ON or IO_HIGH_V. So before we enable the power irq |
| * interrupt in GIC (by registering the interrupt handler), we need to |
| * ensure that any pending power irq interrupt status is acknowledged |
| * otherwise power irq interrupt handler would be fired prematurely. |
| */ |
| irq_status = sdhci_msm_readl_relaxed(host, |
| msm_host_offset->CORE_PWRCTL_STATUS); |
| sdhci_msm_writel_relaxed(irq_status, host, |
| msm_host_offset->CORE_PWRCTL_CLEAR); |
| irq_ctl = sdhci_msm_readl_relaxed(host, |
| msm_host_offset->CORE_PWRCTL_CTL); |
| |
| if (irq_status & (CORE_PWRCTL_BUS_ON | CORE_PWRCTL_BUS_OFF)) |
| irq_ctl |= CORE_PWRCTL_BUS_SUCCESS; |
| if (irq_status & (CORE_PWRCTL_IO_HIGH | CORE_PWRCTL_IO_LOW)) |
| irq_ctl |= CORE_PWRCTL_IO_SUCCESS; |
| sdhci_msm_writel_relaxed(irq_ctl, host, |
| msm_host_offset->CORE_PWRCTL_CTL); |
| |
| /* |
| * Ensure that above writes are propogated before interrupt enablement |
| * in GIC. |
| */ |
| mb(); |
| |
| /* |
| * Following are the deviations from SDHC spec v3.0 - |
| * 1. Card detection is handled using separate GPIO. |
| * 2. Bus power control is handled by interacting with PMIC. |
| */ |
| host->quirks |= SDHCI_QUIRK_BROKEN_CARD_DETECTION; |
| host->quirks |= SDHCI_QUIRK_SINGLE_POWER_WRITE; |
| host->quirks |= SDHCI_QUIRK_CAP_CLOCK_BASE_BROKEN; |
| host->quirks |= SDHCI_QUIRK_NO_ENDATTR_IN_NOPDESC; |
| host->quirks2 |= SDHCI_QUIRK2_ALWAYS_USE_BASE_CLOCK; |
| host->quirks2 |= SDHCI_QUIRK2_IGNORE_DATATOUT_FOR_R1BCMD; |
| host->quirks2 |= SDHCI_QUIRK2_BROKEN_PRESET_VALUE; |
| host->quirks2 |= SDHCI_QUIRK2_USE_RESERVED_MAX_TIMEOUT; |
| host->quirks2 |= SDHCI_QUIRK2_NON_STANDARD_TUNING; |
| host->quirks2 |= SDHCI_QUIRK2_USE_PIO_FOR_EMMC_TUNING; |
| |
| if (host->quirks2 & SDHCI_QUIRK2_ALWAYS_USE_BASE_CLOCK) |
| host->quirks2 |= SDHCI_QUIRK2_DIVIDE_TOUT_BY_4; |
| |
| host_version = readw_relaxed((host->ioaddr + SDHCI_HOST_VERSION)); |
| dev_dbg(&pdev->dev, "Host Version: 0x%x Vendor Version 0x%x\n", |
| host_version, ((host_version & SDHCI_VENDOR_VER_MASK) >> |
| SDHCI_VENDOR_VER_SHIFT)); |
| if (((host_version & SDHCI_VENDOR_VER_MASK) >> |
| SDHCI_VENDOR_VER_SHIFT) == SDHCI_VER_100) { |
| /* |
| * Add 40us delay in interrupt handler when |
| * operating at initialization frequency(400KHz). |
| */ |
| host->quirks2 |= SDHCI_QUIRK2_SLOW_INT_CLR; |
| /* |
| * Set Software Reset for DAT line in Software |
| * Reset Register (Bit 2). |
| */ |
| host->quirks2 |= SDHCI_QUIRK2_RDWR_TX_ACTIVE_EOT; |
| } |
| |
| host->quirks2 |= SDHCI_QUIRK2_IGN_DATA_END_BIT_ERROR; |
| |
| /* Setup PWRCTL irq */ |
| msm_host->pwr_irq = platform_get_irq_byname(pdev, "pwr_irq"); |
| if (msm_host->pwr_irq < 0) { |
| dev_err(&pdev->dev, "Failed to get pwr_irq by name (%d)\n", |
| msm_host->pwr_irq); |
| goto vreg_deinit; |
| } |
| |
| ret = devm_request_threaded_irq(&pdev->dev, msm_host->pwr_irq, NULL, |
| sdhci_msm_pwr_irq, IRQF_ONESHOT, |
| dev_name(&pdev->dev), host); |
| if (ret) { |
| dev_err(&pdev->dev, "Request threaded irq(%d) failed (%d)\n", |
| msm_host->pwr_irq, ret); |
| goto vreg_deinit; |
| } |
| |
| /* Enable pwr irq interrupts */ |
| sdhci_msm_writel_relaxed(INT_MASK, host, |
| msm_host_offset->CORE_PWRCTL_MASK); |
| |
| #ifdef CONFIG_MMC_CLKGATE |
| /* Set clock gating delay to be used when CONFIG_MMC_CLKGATE is set */ |
| msm_host->mmc->clkgate_delay = SDHCI_MSM_MMC_CLK_GATE_DELAY; |
| #endif |
| |
| /* Set host capabilities */ |
| msm_host->mmc->caps |= msm_host->pdata->mmc_bus_width; |
| msm_host->mmc->caps |= msm_host->pdata->caps; |
| msm_host->mmc->caps |= MMC_CAP_AGGRESSIVE_PM; |
| msm_host->mmc->caps |= MMC_CAP_WAIT_WHILE_BUSY; |
| msm_host->mmc->caps2 |= msm_host->pdata->caps2; |
| msm_host->mmc->caps2 |= MMC_CAP2_BOOTPART_NOACC; |
| msm_host->mmc->caps2 |= MMC_CAP2_HS400_POST_TUNING; |
| msm_host->mmc->caps2 |= MMC_CAP2_CLK_SCALE; |
| msm_host->mmc->caps2 |= MMC_CAP2_SANITIZE; |
| msm_host->mmc->caps2 |= MMC_CAP2_MAX_DISCARD_SIZE; |
| msm_host->mmc->caps2 |= MMC_CAP2_SLEEP_AWAKE; |
| msm_host->mmc->pm_caps |= MMC_PM_KEEP_POWER | MMC_PM_WAKE_SDIO_IRQ; |
| |
| if (msm_host->pdata->nonremovable) |
| msm_host->mmc->caps |= MMC_CAP_NONREMOVABLE; |
| |
| if (msm_host->pdata->nonhotplug) |
| msm_host->mmc->caps2 |= MMC_CAP2_NONHOTPLUG; |
| |
| msm_host->mmc->sdr104_wa = msm_host->pdata->sdr104_wa; |
| |
| /* Initialize ICE if present */ |
| if (msm_host->ice.pdev) { |
| ret = sdhci_msm_ice_init(host); |
| if (ret) { |
| dev_err(&pdev->dev, "%s: SDHCi ICE init failed (%d)\n", |
| mmc_hostname(host->mmc), ret); |
| ret = -EINVAL; |
| goto vreg_deinit; |
| } |
| host->is_crypto_en = true; |
| msm_host->mmc->inlinecrypt_support = true; |
| /* Packed commands cannot be encrypted/decrypted using ICE */ |
| msm_host->mmc->caps2 &= ~(MMC_CAP2_PACKED_WR | |
| MMC_CAP2_PACKED_WR_CONTROL); |
| } |
| |
| init_completion(&msm_host->pwr_irq_completion); |
| |
| if (gpio_is_valid(msm_host->pdata->status_gpio)) { |
| /* |
| * Set up the card detect GPIO in active configuration before |
| * configuring it as an IRQ. Otherwise, it can be in some |
| * weird/inconsistent state resulting in flood of interrupts. |
| */ |
| sdhci_msm_setup_pins(msm_host->pdata, true); |
| |
| /* |
| * This delay is needed for stabilizing the card detect GPIO |
| * line after changing the pull configs. |
| */ |
| usleep_range(10000, 10500); |
| ret = mmc_gpio_request_cd(msm_host->mmc, |
| msm_host->pdata->status_gpio, 0); |
| if (ret) { |
| dev_err(&pdev->dev, "%s: Failed to request card detection IRQ %d\n", |
| __func__, ret); |
| goto vreg_deinit; |
| } |
| } |
| |
| if ((sdhci_readl(host, SDHCI_CAPABILITIES) & SDHCI_CAN_64BIT) && |
| (dma_supported(mmc_dev(host->mmc), DMA_BIT_MASK(64)))) { |
| host->dma_mask = DMA_BIT_MASK(64); |
| mmc_dev(host->mmc)->dma_mask = &host->dma_mask; |
| mmc_dev(host->mmc)->coherent_dma_mask = host->dma_mask; |
| } else if (dma_supported(mmc_dev(host->mmc), DMA_BIT_MASK(32))) { |
| host->dma_mask = DMA_BIT_MASK(32); |
| mmc_dev(host->mmc)->dma_mask = &host->dma_mask; |
| mmc_dev(host->mmc)->coherent_dma_mask = host->dma_mask; |
| } else { |
| dev_err(&pdev->dev, "%s: Failed to set dma mask\n", __func__); |
| } |
| |
| msm_host->pdata->sdiowakeup_irq = platform_get_irq_byname(pdev, |
| "sdiowakeup_irq"); |
| if (sdhci_is_valid_gpio_wakeup_int(msm_host)) { |
| dev_info(&pdev->dev, "%s: sdiowakeup_irq = %d\n", __func__, |
| msm_host->pdata->sdiowakeup_irq); |
| msm_host->is_sdiowakeup_enabled = true; |
| ret = request_irq(msm_host->pdata->sdiowakeup_irq, |
| sdhci_msm_sdiowakeup_irq, |
| IRQF_SHARED | IRQF_TRIGGER_HIGH, |
| "sdhci-msm sdiowakeup", host); |
| if (ret) { |
| dev_err(&pdev->dev, "%s: request sdiowakeup IRQ %d: failed: %d\n", |
| __func__, msm_host->pdata->sdiowakeup_irq, ret); |
| msm_host->pdata->sdiowakeup_irq = -1; |
| msm_host->is_sdiowakeup_enabled = false; |
| goto vreg_deinit; |
| } else { |
| spin_lock_irqsave(&host->lock, flags); |
| sdhci_msm_cfg_sdiowakeup_gpio_irq(host, false); |
| msm_host->sdio_pending_processing = false; |
| spin_unlock_irqrestore(&host->lock, flags); |
| } |
| } |
| |
| sdhci_msm_cmdq_init(host, pdev); |
| ret = sdhci_add_host(host); |
| if (ret) { |
| dev_err(&pdev->dev, "Add host failed (%d)\n", ret); |
| goto vreg_deinit; |
| } |
| |
| msm_host->pltfm_init_done = true; |
| |
| pm_runtime_set_active(&pdev->dev); |
| pm_runtime_enable(&pdev->dev); |
| pm_runtime_set_autosuspend_delay(&pdev->dev, MSM_AUTOSUSPEND_DELAY_MS); |
| pm_runtime_use_autosuspend(&pdev->dev); |
| |
| msm_host->msm_bus_vote.max_bus_bw.show = show_sdhci_max_bus_bw; |
| msm_host->msm_bus_vote.max_bus_bw.store = store_sdhci_max_bus_bw; |
| sysfs_attr_init(&msm_host->msm_bus_vote.max_bus_bw.attr); |
| msm_host->msm_bus_vote.max_bus_bw.attr.name = "max_bus_bw"; |
| msm_host->msm_bus_vote.max_bus_bw.attr.mode = S_IRUGO | S_IWUSR; |
| ret = device_create_file(&pdev->dev, |
| &msm_host->msm_bus_vote.max_bus_bw); |
| if (ret) |
| goto remove_host; |
| |
| if (!gpio_is_valid(msm_host->pdata->status_gpio)) { |
| msm_host->polling.show = show_polling; |
| msm_host->polling.store = store_polling; |
| sysfs_attr_init(&msm_host->polling.attr); |
| msm_host->polling.attr.name = "polling"; |
| msm_host->polling.attr.mode = S_IRUGO | S_IWUSR; |
| ret = device_create_file(&pdev->dev, &msm_host->polling); |
| if (ret) |
| goto remove_max_bus_bw_file; |
| } |
| |
| msm_host->auto_cmd21_attr.show = show_auto_cmd21; |
| msm_host->auto_cmd21_attr.store = store_auto_cmd21; |
| sysfs_attr_init(&msm_host->auto_cmd21_attr.attr); |
| msm_host->auto_cmd21_attr.attr.name = "enable_auto_cmd21"; |
| msm_host->auto_cmd21_attr.attr.mode = S_IRUGO | S_IWUSR; |
| ret = device_create_file(&pdev->dev, &msm_host->auto_cmd21_attr); |
| if (ret) { |
| pr_err("%s: %s: failed creating auto-cmd21 attr: %d\n", |
| mmc_hostname(host->mmc), __func__, ret); |
| device_remove_file(&pdev->dev, &msm_host->auto_cmd21_attr); |
| } |
| if (sdhci_msm_is_bootdevice(&pdev->dev)) |
| mmc_flush_detect_work(host->mmc); |
| |
| /* Successful initialization */ |
| goto out; |
| |
| remove_max_bus_bw_file: |
| device_remove_file(&pdev->dev, &msm_host->msm_bus_vote.max_bus_bw); |
| remove_host: |
| dead = (readl_relaxed(host->ioaddr + SDHCI_INT_STATUS) == 0xffffffff); |
| pm_runtime_disable(&pdev->dev); |
| sdhci_remove_host(host, dead); |
| vreg_deinit: |
| sdhci_msm_vreg_init(&pdev->dev, msm_host->pdata, false); |
| bus_unregister: |
| if (msm_host->msm_bus_vote.client_handle) |
| sdhci_msm_bus_cancel_work_and_set_vote(host, 0); |
| sdhci_msm_bus_unregister(msm_host); |
| sleep_clk_disable: |
| if (!IS_ERR(msm_host->sleep_clk)) |
| clk_disable_unprepare(msm_host->sleep_clk); |
| ff_clk_disable: |
| if (!IS_ERR(msm_host->ff_clk)) |
| clk_disable_unprepare(msm_host->ff_clk); |
| clk_disable: |
| if (!IS_ERR(msm_host->clk)) |
| clk_disable_unprepare(msm_host->clk); |
| bus_aggr_clk_disable: |
| if (!IS_ERR(msm_host->bus_aggr_clk)) |
| clk_disable_unprepare(msm_host->bus_aggr_clk); |
| pclk_disable: |
| if (!IS_ERR(msm_host->pclk)) |
| clk_disable_unprepare(msm_host->pclk); |
| bus_clk_disable: |
| if (!IS_ERR_OR_NULL(msm_host->bus_clk)) |
| clk_disable_unprepare(msm_host->bus_clk); |
| pltfm_free: |
| sdhci_pltfm_free(pdev); |
| out_host_free: |
| devm_kfree(&pdev->dev, msm_host); |
| out: |
| pr_debug("%s: Exit %s\n", dev_name(&pdev->dev), __func__); |
| return ret; |
| } |
| |
| static int sdhci_msm_remove(struct platform_device *pdev) |
| { |
| struct sdhci_host *host = platform_get_drvdata(pdev); |
| struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); |
| struct sdhci_msm_host *msm_host = pltfm_host->priv; |
| struct sdhci_msm_pltfm_data *pdata = msm_host->pdata; |
| int nr_groups = msm_host->pdata->pm_qos_data.cpu_group_map.nr_groups; |
| int i; |
| int dead = (readl_relaxed(host->ioaddr + SDHCI_INT_STATUS) == |
| 0xffffffff); |
| |
| pr_debug("%s: %s Enter\n", dev_name(&pdev->dev), __func__); |
| if (!gpio_is_valid(msm_host->pdata->status_gpio)) |
| device_remove_file(&pdev->dev, &msm_host->polling); |
| |
| device_remove_file(&pdev->dev, &msm_host->auto_cmd21_attr); |
| device_remove_file(&pdev->dev, &msm_host->msm_bus_vote.max_bus_bw); |
| pm_runtime_disable(&pdev->dev); |
| |
| if (msm_host->pm_qos_group_enable) { |
| struct sdhci_msm_pm_qos_group *group; |
| |
| for (i = 0; i < nr_groups; i++) |
| cancel_delayed_work_sync( |
| &msm_host->pm_qos[i].unvote_work); |
| |
| device_remove_file(&msm_host->pdev->dev, |
| &msm_host->pm_qos_group_enable_attr); |
| device_remove_file(&msm_host->pdev->dev, |
| &msm_host->pm_qos_group_status_attr); |
| |
| for (i = 0; i < nr_groups; i++) { |
| group = &msm_host->pm_qos[i]; |
| pm_qos_remove_request(&group->req); |
| } |
| } |
| |
| if (msm_host->pm_qos_irq.enabled) { |
| cancel_delayed_work_sync(&msm_host->pm_qos_irq.unvote_work); |
| device_remove_file(&pdev->dev, |
| &msm_host->pm_qos_irq.enable_attr); |
| device_remove_file(&pdev->dev, |
| &msm_host->pm_qos_irq.status_attr); |
| pm_qos_remove_request(&msm_host->pm_qos_irq.req); |
| } |
| |
| if (msm_host->pm_qos_wq) |
| destroy_workqueue(msm_host->pm_qos_wq); |
| |
| sdhci_remove_host(host, dead); |
| |
| sdhci_msm_vreg_init(&pdev->dev, msm_host->pdata, false); |
| |
| sdhci_msm_setup_pins(pdata, true); |
| sdhci_msm_setup_pins(pdata, false); |
| |
| if (msm_host->msm_bus_vote.client_handle) { |
| sdhci_msm_bus_cancel_work_and_set_vote(host, 0); |
| sdhci_msm_bus_unregister(msm_host); |
| } |
| |
| sdhci_pltfm_free(pdev); |
| |
| return 0; |
| } |
| |
| #ifdef CONFIG_PM |
| static int sdhci_msm_cfg_sdio_wakeup(struct sdhci_host *host, bool enable) |
| { |
| struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); |
| struct sdhci_msm_host *msm_host = pltfm_host->priv; |
| unsigned long flags; |
| int ret = 0; |
| |
| if (!(host->mmc->card && mmc_card_sdio(host->mmc->card) && |
| sdhci_is_valid_gpio_wakeup_int(msm_host) && |
| mmc_card_wake_sdio_irq(host->mmc))) { |
| msm_host->sdio_pending_processing = false; |
| return 1; |
| } |
| |
| spin_lock_irqsave(&host->lock, flags); |
| if (enable) { |
| /* configure DAT1 gpio if applicable */ |
| if (sdhci_is_valid_gpio_wakeup_int(msm_host)) { |
| msm_host->sdio_pending_processing = false; |
| ret = enable_irq_wake(msm_host->pdata->sdiowakeup_irq); |
| if (!ret) |
| sdhci_msm_cfg_sdiowakeup_gpio_irq(host, true); |
| goto out; |
| } else { |
| pr_err("%s: sdiowakeup_irq(%d) invalid\n", |
| mmc_hostname(host->mmc), enable); |
| } |
| } else { |
| if (sdhci_is_valid_gpio_wakeup_int(msm_host)) { |
| ret = disable_irq_wake(msm_host->pdata->sdiowakeup_irq); |
| sdhci_msm_cfg_sdiowakeup_gpio_irq(host, false); |
| msm_host->sdio_pending_processing = false; |
| } else { |
| pr_err("%s: sdiowakeup_irq(%d)invalid\n", |
| mmc_hostname(host->mmc), enable); |
| |
| } |
| } |
| out: |
| if (ret) |
| pr_err("%s: %s: %sable wakeup: failed: %d gpio: %d\n", |
| mmc_hostname(host->mmc), __func__, enable ? "en" : "dis", |
| ret, msm_host->pdata->sdiowakeup_irq); |
| spin_unlock_irqrestore(&host->lock, flags); |
| return ret; |
| } |
| |
| |
| static int sdhci_msm_runtime_suspend(struct device *dev) |
| { |
| struct sdhci_host *host = dev_get_drvdata(dev); |
| struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); |
| struct sdhci_msm_host *msm_host = pltfm_host->priv; |
| ktime_t start = ktime_get(); |
| int ret; |
| |
| if (host->mmc->card && mmc_card_sdio(host->mmc->card)) |
| goto defer_disable_host_irq; |
| |
| sdhci_cfg_irq(host, false, true); |
| |
| defer_disable_host_irq: |
| disable_irq(msm_host->pwr_irq); |
| |
| /* |
| * Remove the vote immediately only if clocks are off in which |
| * case we might have queued work to remove vote but it may not |
| * be completed before runtime suspend or system suspend. |
| */ |
| if (!atomic_read(&msm_host->clks_on)) { |
| if (msm_host->msm_bus_vote.client_handle) |
| sdhci_msm_bus_cancel_work_and_set_vote(host, 0); |
| } |
| |
| if (host->is_crypto_en) { |
| ret = sdhci_msm_ice_suspend(host); |
| if (ret < 0) |
| pr_err("%s: failed to suspend crypto engine %d\n", |
| mmc_hostname(host->mmc), ret); |
| } |
| trace_sdhci_msm_runtime_suspend(mmc_hostname(host->mmc), 0, |
| ktime_to_us(ktime_sub(ktime_get(), start))); |
| return 0; |
| } |
| |
| static int sdhci_msm_runtime_resume(struct device *dev) |
| { |
| struct sdhci_host *host = dev_get_drvdata(dev); |
| struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); |
| struct sdhci_msm_host *msm_host = pltfm_host->priv; |
| ktime_t start = ktime_get(); |
| int ret; |
| |
| if (host->is_crypto_en) { |
| ret = sdhci_msm_enable_controller_clock(host); |
| if (ret) { |
| pr_err("%s: Failed to enable reqd clocks\n", |
| mmc_hostname(host->mmc)); |
| goto skip_ice_resume; |
| } |
| ret = sdhci_msm_ice_resume(host); |
| if (ret) |
| pr_err("%s: failed to resume crypto engine %d\n", |
| mmc_hostname(host->mmc), ret); |
| } |
| skip_ice_resume: |
| |
| if (host->mmc->card && mmc_card_sdio(host->mmc->card)) |
| goto defer_enable_host_irq; |
| |
| sdhci_cfg_irq(host, true, true); |
| |
| defer_enable_host_irq: |
| enable_irq(msm_host->pwr_irq); |
| |
| trace_sdhci_msm_runtime_resume(mmc_hostname(host->mmc), 0, |
| ktime_to_us(ktime_sub(ktime_get(), start))); |
| return 0; |
| } |
| |
| static int sdhci_msm_suspend(struct device *dev) |
| { |
| struct sdhci_host *host = dev_get_drvdata(dev); |
| struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); |
| struct sdhci_msm_host *msm_host = pltfm_host->priv; |
| struct mmc_host *mmc = host->mmc; |
| int ret = 0; |
| int sdio_cfg = 0; |
| ktime_t start = ktime_get(); |
| |
| if (gpio_is_valid(msm_host->pdata->status_gpio) && |
| (msm_host->mmc->slot.cd_irq >= 0)) |
| disable_irq(msm_host->mmc->slot.cd_irq); |
| |
| if (pm_runtime_suspended(dev)) { |
| pr_debug("%s: %s: already runtime suspended\n", |
| mmc_hostname(host->mmc), __func__); |
| goto out; |
| } |
| ret = sdhci_msm_runtime_suspend(dev); |
| out: |
| /* cancel any clock gating work scheduled by mmc_host_clk_release() */ |
| cancel_delayed_work_sync(&mmc->clk_gate_work); |
| sdhci_msm_disable_controller_clock(host); |
| if (host->mmc->card && mmc_card_sdio(host->mmc->card)) { |
| sdio_cfg = sdhci_msm_cfg_sdio_wakeup(host, true); |
| if (sdio_cfg) |
| sdhci_cfg_irq(host, false, true); |
| } |
| |
| trace_sdhci_msm_suspend(mmc_hostname(host->mmc), ret, |
| ktime_to_us(ktime_sub(ktime_get(), start))); |
| return ret; |
| } |
| |
| static int sdhci_msm_resume(struct device *dev) |
| { |
| struct sdhci_host *host = dev_get_drvdata(dev); |
| struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); |
| struct sdhci_msm_host *msm_host = pltfm_host->priv; |
| int ret = 0; |
| int sdio_cfg = 0; |
| ktime_t start = ktime_get(); |
| |
| if (gpio_is_valid(msm_host->pdata->status_gpio) && |
| (msm_host->mmc->slot.cd_irq >= 0)) |
| enable_irq(msm_host->mmc->slot.cd_irq); |
| |
| if (pm_runtime_suspended(dev)) { |
| pr_debug("%s: %s: runtime suspended, defer system resume\n", |
| mmc_hostname(host->mmc), __func__); |
| goto out; |
| } |
| |
| ret = sdhci_msm_runtime_resume(dev); |
| out: |
| if (host->mmc->card && mmc_card_sdio(host->mmc->card)) { |
| sdio_cfg = sdhci_msm_cfg_sdio_wakeup(host, false); |
| if (sdio_cfg) |
| sdhci_cfg_irq(host, true, true); |
| } |
| |
| trace_sdhci_msm_resume(mmc_hostname(host->mmc), ret, |
| ktime_to_us(ktime_sub(ktime_get(), start))); |
| return ret; |
| } |
| |
| static int sdhci_msm_suspend_noirq(struct device *dev) |
| { |
| struct sdhci_host *host = dev_get_drvdata(dev); |
| struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host); |
| struct sdhci_msm_host *msm_host = pltfm_host->priv; |
| int ret = 0; |
| |
| /* |
| * ksdioirqd may be running, hence retry |
| * suspend in case the clocks are ON |
| */ |
| if (atomic_read(&msm_host->clks_on)) { |
| pr_warn("%s: %s: clock ON after suspend, aborting suspend\n", |
| mmc_hostname(host->mmc), __func__); |
| ret = -EAGAIN; |
| } |
| |
| if (host->mmc->card && mmc_card_sdio(host->mmc->card)) |
| if (msm_host->sdio_pending_processing) |
| ret = -EBUSY; |
| |
| return ret; |
| } |
| |
| static const struct dev_pm_ops sdhci_msm_pmops = { |
| SET_LATE_SYSTEM_SLEEP_PM_OPS(sdhci_msm_suspend, sdhci_msm_resume) |
| SET_RUNTIME_PM_OPS(sdhci_msm_runtime_suspend, sdhci_msm_runtime_resume, |
| NULL) |
| .suspend_noirq = sdhci_msm_suspend_noirq, |
| }; |
| |
| #define SDHCI_MSM_PMOPS (&sdhci_msm_pmops) |
| |
| #else |
| #define SDHCI_MSM_PMOPS NULL |
| #endif |
| static const struct of_device_id sdhci_msm_dt_match[] = { |
| {.compatible = "qcom,sdhci-msm"}, |
| {.compatible = "qcom,sdhci-msm-v5"}, |
| {}, |
| }; |
| MODULE_DEVICE_TABLE(of, sdhci_msm_dt_match); |
| |
| static struct platform_driver sdhci_msm_driver = { |
| .probe = sdhci_msm_probe, |
| .remove = sdhci_msm_remove, |
| .driver = { |
| .name = "sdhci_msm", |
| .owner = THIS_MODULE, |
| .probe_type = PROBE_PREFER_ASYNCHRONOUS, |
| .of_match_table = sdhci_msm_dt_match, |
| .pm = SDHCI_MSM_PMOPS, |
| }, |
| }; |
| |
| module_platform_driver(sdhci_msm_driver); |
| |
| MODULE_DESCRIPTION("Qualcomm Technologies, Inc. Secure Digital Host Controller Interface driver"); |
| MODULE_LICENSE("GPL v2"); |