| # This file allows user to override the factory |
| # defaults for the WLAN Driver |
| |
| # Enable IMPS or not |
| gEnableImps=1 |
| |
| # Enable BMPS or not |
| gEnableBmps=1 |
| |
| # Phy Mode (auto, b, g, n, etc) |
| # Valid values are 0-9, with 0 = Auto, 4 = 11n, 9 = 11ac |
| # 1 = 11abg, 2 = 11b, 3 = 11g, 5 = 11g only, 6 = 11n only |
| # 7 = 11b only 8 = 11ac only. |
| gDot11Mode=0 |
| |
| # Assigned MAC Addresses - This will be used until NV items are in place |
| # Each byte of MAC address is represented in Hex format as XX |
| Intf0MacAddress=000AF58989FF |
| Intf1MacAddress=000AF58989FE |
| Intf2MacAddress=000AF58989FD |
| Intf3MacAddress=000AF58989FC |
| |
| # UAPSD service interval for VO,VI, BE, BK traffic |
| InfraUapsdVoSrvIntv=0 |
| InfraUapsdViSrvIntv=0 |
| InfraUapsdBeSrvIntv=0 |
| InfraUapsdBkSrvIntv=0 |
| |
| # Flag to allow STA send AddTspec even when ACM is Off |
| gAddTSWhenACMIsOff=1 |
| |
| # Flags to filter Mcast and Bcast RX packets. |
| # Value 0: No filtering, 1: Filter all Multicast. |
| # 2: Filter all Broadcast. 3: Filter all Mcast abd Bcast |
| McastBcastFilter=3 |
| |
| #Flag to enable HostARPOffload feature or not |
| hostArpOffload=1 |
| |
| #Flag to enable HostNSOffload feature or not |
| hostNSOffload=1 |
| |
| # 802.11n Protection flag |
| gEnableApProt=1 |
| |
| #Enable OBSS protection |
| gEnableApOBSSProt=1 |
| |
| #Enable/Disable UAPSD for SoftAP |
| gEnableApUapsd=1 |
| |
| # Fixed Rate |
| gFixedRate=0 |
| |
| # Maximum Tx power |
| # gTxPowerCap=30 |
| |
| # Fragmentation Threshold |
| # gFragmentationThreshold=2346 |
| |
| # RTS threshold |
| RTSThreshold=1048576 |
| |
| # Intra-BSS forward |
| gDisableIntraBssFwd=0 |
| |
| # WMM Enable/Disable |
| WmmIsEnabled=0 |
| |
| # 802.11d support |
| g11dSupportEnabled=0 |
| |
| # 802.11h support |
| g11hSupportEnabled=1 |
| |
| # DFS Master Capability |
| gEnableDFSMasterCap=1 |
| |
| # ESE Support and fast transition |
| EseEnabled=0 |
| |
| ImplicitQosIsEnabled=0 |
| |
| gNeighborScanTimerPeriod=200 |
| gNeighborLookupThreshold=65 |
| gNeighborScanChannelMinTime=20 |
| gNeighborScanChannelMaxTime=30 |
| gMaxNeighborReqTries=3 |
| |
| # Legacy (non-ESE, non-802.11r) Fast Roaming Support |
| # To enable, set FastRoamEnabled=1 |
| # To disable, set FastRoamEnabled=0 |
| FastRoamEnabled=1 |
| |
| # Check if the AP to which we are roaming is better than current AP in |
| # terms of RSSI. Checking is disabled if set to Zero.Otherwise it will |
| # use this value as to how better the RSSI of the new/roamable AP should |
| # be for roaming |
| RoamRssiDiff=5 |
| |
| # To enable, set gRoamIntraBand=1 (Roaming within band) |
| # To disable, set gRoamIntraBand=0 (Roaming across band) |
| gRoamIntraBand=0 |
| |
| #Short Guard Interval Enable/disable |
| gShortGI20Mhz=1 |
| gShortGI40Mhz=1 |
| |
| #Auto Shutdown Value in seconds. A value of 0 means Auto shutoff is disabled |
| gAPAutoShutOff=0 |
| |
| #Auto Shutdown wlan : Value in Seconds. 0 means disabled. Max 1 day = 86400 sec |
| gWlanAutoShutdown = 0 |
| |
| # Not used. |
| gApAutoChannelSelection=0 |
| |
| #Preferred band (both or 2.4 only or 5 only) |
| BandCapability=0 |
| |
| #Channel Bonding |
| gChannelBondingMode5GHz=1 |
| |
| #Say gGoKeepAlivePeriod(5 seconds) and gGoLinkMonitorPeriod(10 seconds). |
| #For every 10 seconds DUT send Qos Null frame(i.e., Keep Alive frame if link |
| #is idle for last 10 seconds.) For both active and power save clients. |
| |
| #Power save clients: DUT set TIM bit from 10th second onwards and till client |
| #honors TIM bit. If doesn't honor for 5 seconds then DUT remove client. |
| |
| #Active clients: DUT send Qos Null frame for 10th seconds onwards if it is not |
| #success still we try on 11th second if not tries on 12th and so on till 15th |
| #second. Hence before disconnection DUT will send 5 NULL frames. Hence in any |
| #case DUT will detect client got removed in (10+5) seconds. |
| #i.e., (gGoKeepAlivePeriod + gGoLinkMonitorPeriod).. |
| |
| #gGoLinkMonitorPeriod/ gApLinkMonitorPeriod is period where link is idle and |
| #it is period where we send NULL frame. |
| #gApLinkMonitorPeriod = 10 |
| #gGoLinkMonitorPeriod = 10 |
| |
| #gGoKeepAlivePeriod/gApKeepAlivePeriod is time to spend to check whether frame |
| #are succeed to send or not. Hence total effective detection time is |
| # (gGoLinkMonitorPeriod + gGoKeepAlivePeriod) / |
| # (gApLinkMonitorPeriod + gApKeepAlivePeriod) |
| gGoKeepAlivePeriod = 20 |
| gApKeepAlivePeriod = 20 |
| |
| #If set will start with active scan after driver load, otherwise will start with |
| #passive scan to find out the domain |
| gEnableBypass11d=1 |
| |
| #If set to 0, will not scan DFS channels |
| gEnableDFSChnlScan=1 |
| |
| # Enable DFS channel roam |
| # 0: DISABLE, 1: ENABLED_NORMAL, 2: ENABLED_ACTIVE |
| gAllowDFSChannelRoam=1 |
| |
| gVhtChannelWidth=2 |
| |
| #Data Inactivity Timeout when in powersave (in ms) |
| gDataInactivityTimeout=200 |
| |
| # Set txchainmask and rxchainmask |
| # These parameters are used only if gEnable2x2 is 0 |
| # Valid values are 1,2 |
| # Set gSetTxChainmask1x1=1 or gSetRxChainmask1x1=1 to select chain0. |
| # Set gSetTxChainmask1x1=2 or gSetRxChainmask1x1=2 to select chain1. |
| gSetTxChainmask1x1=1 |
| gSetRxChainmask1x1=1 |
| |
| # Scan Timing Parameters |
| # gPassiveMaxChannelTime=110 |
| # gPassiveMinChannelTime=60 |
| gActiveMaxChannelTime=40 |
| gActiveMinChannelTime=20 |
| |
| #If set to 0, MCC is not allowed. |
| gEnableMCCMode=1 |
| |
| # MCC to SCC Switch mode: |
| # 0-Disable |
| # 1-Enable |
| # 2-Force SCC if same band, with SAP restart |
| # 3-Force SCC if same band, without SAP restart by sending (E)CSA |
| # 4-Force SCC if same band (or) use SAP mandatory channel for DBS, |
| # without SAP restart by sending (E)CSA |
| gWlanMccToSccSwitchMode = 3 |
| |
| # 1=enable STBC; 0=disable STBC |
| gEnableRXSTBC=1 |
| |
| # 1=enable tx STBC; 0=disable |
| gEnableTXSTBC=1 |
| |
| # 1=enable rx LDPC; 0=disable |
| gEnableRXLDPC=1 |
| |
| #Enable/Disable Tx beamforming |
| gTxBFEnable=1 |
| |
| #Enable/Disable Tx beamformee in SAP mode |
| gEnableTxBFeeSAP=1 |
| |
| # Enable Tx beamforming in VHT20MHz |
| # Valid values are 0,1. If commented out, the default value is 0. |
| # 0=disable, 1=enable |
| gEnableTxBFin20MHz=1 |
| |
| #Enable/Disable SU Tx beamformer support. |
| gEnableTxSUBeamformer=1 |
| |
| gEnableFastRoamInConcurrency=1 |
| |
| #Maxium Channel time in msec |
| gMaxMediumTime = 6000 |
| |
| # 802.11K support |
| gRrmEnable=1 |
| |
| #Enable Power Save offload |
| gEnablePowerSaveOffload=2 |
| |
| #Enable firmware uart print |
| gEnablefwprint=0 |
| |
| # Firmware log mode |
| # Valid values are 0,1,2 |
| # 0=Disable, 1=WMI, 2=DIAG |
| gEnablefwlog=1 |
| |
| # Maximum Receive AMPDU size (VHT only. Valid values: |
| # 0->8k 1->16k 2->32k 3->64k 4->128k) |
| gVhtAmpduLenExponent=7 |
| |
| # Maximum MPDU length (VHT only. Valid values: |
| # 0->3895 octets, 1->7991 octets, 2->11454 octets) |
| gVhtMpduLen=2 |
| |
| # Maximum number of wow filters required |
| #gMaxWoWFilters=22 |
| |
| # WOW Enable/Disable. |
| # 0 - Disable both magic pattern match and pattern byte match. |
| # 1 - Enable magic pattern match on all interfaces. |
| # 2 - Enable pattern byte match on all interfaces. |
| # 3 - Enable both magic pattern and pattern byte match on all interfaces. |
| # Default value of gEnableWoW is 3. |
| # gEnableWoW=0 |
| |
| # Enable or Disable MCC Adaptive Scheduler at the FW |
| # 1=Enable (default), 0=Disable |
| gEnableMCCAdaptiveScheduler=1 |
| |
| #Enable or Disable p2p device address administered |
| isP2pDeviceAddrAdministrated=0 |
| |
| # Remove Overlap channel restriction |
| gEnableOverLapCh=0 |
| |
| #Enable VHT on 2.4Ghz |
| gEnableVhtFor24GHzBand=1 |
| |
| #Maximum number of offload peers supported |
| # gMaxOffloadPeers=2 |
| |
| # controlling the following offload patterns |
| # through ini parameter. Default value is 1 |
| # to disable set it to zero. ssdp = 0 |
| # Setup multicast pattern for mDNS 224.0.0.251, |
| # SSDP 239.255.255.250 and LLMNR 224.0.0.252 |
| ssdp=0 |
| |
| #Enable Memory Deep Sleep |
| gEnableMemDeepSleep=1 |
| |
| # Regulatory Setting; 0=STRICT; 1=CUSTOM |
| gRegulatoryChangeCountry=1 |
| |
| # RA filtering rate limit param, the current value would not |
| # help if the lifetime in RA is less than 3*60=3min. Then |
| # we need to change it, though it is uncommon. |
| # gRAFilterEnable=0 |
| gRArateLimitInterval=600 |
| |
| # Maximum number of concurrent connections |
| gMaxConcurrentActiveSessions=3 |
| |
| # Disable/Enable GreenAP |
| # 0 to disable, 1 to enable, default: 1 |
| gEnableGreenAp=0 |
| |
| # Radar PRI multiplier |
| gDFSradarMappingPriMultiplier=4 |
| |
| gPNOScanSupport=1 |
| |
| #Enable/Disable LPASS support |
| # 0 to disable, 1 to enable |
| gEnableLpassSupport=1 |
| |
| # Whether userspace country code setting shld have priority |
| gCountryCodePriority=1 |
| |
| # Enable(1)/Disable(0) SIFS burst |
| gEnableSifsBurst=1 |
| |
| # Enable or Disable Multi-user MIMO |
| # 1=Enable (default), 0=Disable |
| gEnableMuBformee=1 |
| |
| # Enable/Disable channel avoidance for SAP in SCC scenario |
| # 0 - disable |
| # 1 - enable |
| gSapSccChanAvoidance=0 |
| |
| # Inactivity time (in ms) to end TX Service Period while in IBSS power save mode |
| gIbssTxSpEndInactivityTime=10 |
| |
| # Enable TDLS External Control. That is, user space application has to |
| # first configure a peer MAC in wlan driver towards which TDLS is desired. |
| # Device will establish TDLS only towards those configured peers whenever |
| # TDLS criteria (throughput and RSSI threshold) is met and teardown TDLS |
| # when teardown criteria (idle packet count and RSSI) is met. However, |
| # device will accept TDLS connection if it is initiated from any other peer, |
| # even if that peer is not configured. |
| # 0 - disable |
| # 1 - enable |
| # For TDLS External Control, Implicit Trigger must also be enabled. |
| gTDLSExternalControl=1 |
| |
| # Enable support for TDLS off-channel operation |
| # 0 - disable |
| # 1 - enable |
| # TDLS off-channel operation will be invoked when there is only one |
| # TDLS connection. |
| gEnableTDLSOffChannel=1 |
| |
| # Enable or Disable Random MAC (Spoofing) |
| # 1=Enable (default), 0=Disable |
| gEnableMacAddrSpoof=1 |
| |
| ################ Datapath feature set Begin ################ |
| # Bus bandwidth threshold values in terms of number of packets |
| gBusBandwidthHighThreshold=2000 |
| gBusBandwidthMediumThreshold=500 |
| gBusBandwidthLowThreshold=150 |
| |
| # Bus bandwidth compute timeout value in ms |
| gBusBandwidthComputeInterval=100 |
| |
| # VHT Tx/Rx MCS values |
| # Valid values are 0,1,2. If commented out, the default value is 0. |
| # 0=MCS0-7, 1=MCS0-8, 2=MCS0-9 |
| gVhtRxMCS=2 |
| gVhtTxMCS=2 |
| |
| # VHT Tx/Rx MCS values for 2x2 |
| # Valid values are 0,1,2. If commented out, the default value is 0. |
| # 0=MCS0-7, 1=MCS0-8, 2=MCS0-9 |
| gEnable2x2=1 |
| gVhtRxMCS2x2=2 |
| gVhtTxMCS2x2=2 |
| |
| #IPA config is a bit mask and following are the configurations. |
| #bit0 IPA Enable |
| #bit1 IPA PRE Filter enable |
| #bit2 IPv6 enable |
| #bit3 IPA Resource Manager (RM) enable |
| #bit4 IPA Clock scaling enable |
| #bit5 IPA uC ENABLE |
| #bit6 IPA uC STA ENABLE |
| #bit8 IPA Real Time Debugging |
| gIPAConfig=0x7d |
| gIPADescSize=800 |
| |
| # Enable/Disable RX full reorder offload |
| gReorderOffloadSupported=1 |
| |
| # Enable CE classification |
| # 1 - enable(default) 0 - disable |
| gCEClassifyEnable=1 |
| |
| # Enable Rx handling options |
| # Rx_thread=1 RPS=2(default for ROME) NAPI=4(default for ihelium) |
| rx_mode=5 |
| |
| # Enable(Tx) fastpath for data traffic. |
| # 1 - enable(default) 0 - disable |
| gEnableFastPath=1 |
| |
| # This flag enables IP, TCP and UDP checksum offload |
| # 1 - enable(default) 0 - disable |
| gEnableIpTcpUdpChecksumOffload=1 |
| |
| # Enable TCP Segmentation Offload |
| # 1 - enable 0 - disable |
| TSOEnable=1 |
| |
| # Enable Generic Receive Offload |
| # 1 - enable(default) 0 - disable |
| GROEnable=1 |
| |
| # Enable HT MPDU Density |
| # 4 for 2 micro sec |
| ght_mpdu_density=4 |
| |
| # Enable flow steering to enable multiple CEs for Rx flows. |
| # Multiple Rx CEs<==>Multiple Rx IRQs<==>probably different CPUs. |
| # Parallel Rx paths. |
| # 1 - enable 0 - disable(default) |
| gEnableFlowSteering=1 |
| |
| # Time in microseconds after which a NAPI poll must yield |
| ce_service_max_yield_time=500 |
| |
| #Maximum number of HTT messages to be processed per NAPI poll |
| ce_service_max_rx_ind_flush=1 |
| |
| # Maximum number of MSDUs the firmware will pack in one HTT_T2H_MSG_TYPE_RX_IN_ORD_PADDR_IND |
| maxMSDUsPerRxInd=8 |
| |
| # Enable NUD tracking feature |
| # 1 - enable 0 - disable(default) |
| gEnableNUDTracking=1 |
| |
| # Enable PEER UNMAP CONF SUPPORT |
| # 1 - enable 0 - disable(default) |
| gEnablePeerUnmapConfSupport=1 |
| |
| ################ Datapath feature set End ################ |
| |
| ################ NAN feature set start ################### |
| |
| # Enable NAN discovery (NAN 1.0) |
| # 1 - enable 0 - disable(default) |
| gEnableNanSupport=1 |
| # Enable NAN Datapath |
| genable_nan_datapath=1 |
| |
| ################ NAN feature set end ##################### |
| |
| adaptive_dwell_mode_enabled=1 |
| |
| hostscan_adaptive_dwell_mode=1 |
| |
| adapt_dwell_lpf_weight=80 |
| |
| adapt_dwell_wifi_act_threshold=10 |
| |
| MAWCEnabled=0 |
| |
| # Enable/Disable rtt sta mac randomization |
| enable_rtt_mac_randomization=1 |
| |
| #Enable/Disable SNR monitoring |
| gEnableSNRMonitoring=1 |
| |
| # Rx thread affinity mask in UL case |
| RX_THREAD_UL_CPU_AFFINITY_MASK=0xc0 |
| END |
| |
| # Note: Configuration parser would not read anything past the END marker |
| |