LOCAL_REQUIRED_MODULES requires listed modules to exist {#BUILD_BROKEN_MISSING_REQUIRED_MODULES}Modules listed in LOCAL_REQUIRED_MODULES, LOCAL_HOST_REQUIRED_MODULES and LOCAL_TARGET_REQUIRED_MODULES need to exist unless ALLOW_MISSING_DEPENDENCIES is set.
To temporarily relax missing required modules check, use:
BUILD_BROKEN_MISSING_REQUIRED_MODULES := true
System properties for each of the partition is supposed to be set via following product config variables.
For system partititon,
PRODUCT_SYSTEM_PROPERITESPRODUCT_SYSTEM_DEFAULT_PROPERTIES is highly discouraged. Will be deprecated.For vendor partition,
PRODUCT_VENDOR_PROPERTIESPRODUCT_PROPERTY_OVERRIDES is highly discouraged. Will be deprecated.PRODUCT_DEFAULT_PROPERTY_OVERRIDES is also discouraged. Will be deprecated.For odm partition,
PRODUCT_ODM_PROPERTIESFor system_ext partition,
PRODUCT_SYSTEM_EXT_PROPERTIESFor product partition,
PRODUCT_PRODUCT_PROPERTIESFor each partition, having multiple sysprop assignments for the same name is prohibited. For example, the following will now trigger an error:
PRODUCT_VENDOR_PROPERTIES += foo=true foo=false
Having duplication across partitions are still allowed. So, the following is not an error:
PRODUCT_VENDOR_PROPERTIES += foo=true PRODUCT_SYSTEM_PROPERTIES += foo=false
In that case, the final value is determined at runtime. The precedence is
So, foo becomes true because vendor has higher priority than system.
To temporarily turn the build-time restriction off, use
BUILD_BROKEN_DUP_SYSPROP := true
System properties can now be set as optional using the new syntax:
name ?= value
Then the system property named name gets the value value only when there is no other non-optional assignments having the same name. For example, the following is allowed and foo gets true
PRODUCT_VENDOR_PROPERTIES += foo=true foo?=false
Note that the order between the optional and the non-optional assignments doesn't matter. The following gives the same result as above.
PRODUCT_VENDOR_PROPERTIES += foo?=false foo=true
Optional assignments can be duplicated and in that case their order matters. Specifically, the last one eclipses others.
PRODUCT_VENDOR_PROPERTIES += foo?=apple foo?=banana foo?=mango
With above, foo becomes mango since its the last one.
Note that this behavior is different from the previous behavior of preferring the first one. To go back to the original behavior for compatability reason, use:
BUILD_BROKEN_DUP_SYSPROP := true
PRODUCT_COPY_FILES {#BUILD_BROKEN_ELF_PREBUILT_PRODUCT_COPY_FILES}ELF prebuilts in PRODUCT_COPY_FILES that are installed into these paths are an error:
<partition>/bin/*<partition>/lib/*<partition>/lib64/*Define prebuilt modules and add them to PRODUCT_PACKAGES instead. To temporarily relax this check and restore the behavior prior to this change, set BUILD_BROKEN_ELF_PREBUILT_PRODUCT_COPY_FILES := true in BoardConfig.mk.
We've considered BUILD_COPY_HEADERS/LOCAL_COPY_HEADERS to be deprecated for a long time, and the places where it's been able to be used have shrinked over the last several releases. Equivalent functionality is not available in Soong.
See the build/soong/docs/best_practices.md#headers for more information about how best to handle headers in Android.
m4 is not available on $PATHThere is a prebuilt of it available in prebuilts/build-tools, and a make variable M4 that contains the path.
Beyond the direct usage, whenever you use bison or flex directly, they call m4 behind the scene, so you must set the M4 environment variable (and depend upon it for incremental build correctness):
$(intermediates)/foo.c: .KATI_IMPLICIT_OUTPUTS := $(intermediates)/foo.h $(intermediates)/foo.c: $(LOCAL_PATH)/foo.y $(M4) $(BISON) $(BISON_DATA) M4=$(M4) $(BISON) ...
With ALLOW_NINJA_ENV=false (soon to be the default), ninja, and all the rules/actions executed within it will only have access to a limited number of environment variables. Ninja does not track when environment variables change in order to trigger rebuilds, so changing behavior based on arbitrary variables is not safe with incremental builds.
Kati and Soong can safely use environment variables, so the expectation is that you'd embed any environment variables that you need to use within the command line generated by those tools. See the export section below for examples.
For a temporary workaround, you can set ALLOW_NINJA_ENV=true in your environment to restore the previous behavior, or set BUILD_BROKEN_NINJA_USES_ENV_VAR := <var> <var2> ... in your BoardConfig.mk to allow specific variables to be passed through until you've fixed the rules.
Include directories are expected to be within the source tree (or in the output directory, generated during the build). This has been checked in some form since Oreo, but now has better checks.
There's now a BUILD_BROKEN_OUTSIDE_INCLUDE_DIRS variable, that when set, will turn these errors into warnings temporarily. I don't expect this to last more than a release, since they're fairly easy to clean up.
Neither of these cases are supported by Soong, and will produce errors when converting your module.
This has been checked since Oreo. The common reason to hit this is because a makefile is calculating a path, and ran abspath/realpath/etc. This is a problem because it makes your build non-reproducible. It's very unlikely that your source path is the same on every machine.
../ to leave the source/output directoriesThis is the new check that has been added. In every case I've found, this has been a mistake in the Android.mk -- assuming that LOCAL_C_INCLUDES (which is relative to the top of the source tree) acts like LOCAL_SRC_FILES (which is relative to LOCAL_PATH).
Since this usually isn't a valid path, you can almost always just remove the offending line.
BOARD_HAL_STATIC_LIBRARIES and LOCAL_HAL_STATIC_LIBRARIES are obsolete {#BOARD_HAL_STATIC_LIBRARIES}Define proper HIDL / Stable AIDL HAL instead.
For libhealthd, use health HAL. See instructions for implementing health HAL:
For libdumpstate, use at least Dumpstate HAL 1.0.
PRODUCT_STATIC_BOOT_CONTROL_HAL was the workaround to allow sideloading with statically linked boot control HAL, before shared library HALs were supported under recovery. Android Q has added such support (HALs will be loaded in passthrough mode), and the workarounds are being removed. Targets should build and install the recovery variant of boot control HAL modules into recovery image, similar to the ones installed for normal boot. See the change to crosshatch for example of this:
bootctrl.sdm845 building rulesbootctrl.sdm845.recovery and android.hardware.boot@1.0-impl.recovery into recovery imageBUILD_* module typesSee build/make/Deprecation.md for the current status.
PRODUCT_HOST_PACKAGES split from PRODUCT_PACKAGES {#PRODUCT_HOST_PACKAGES}Previously, adding a module to PRODUCT_PACKAGES that supported both the host and the target (host_supported in Android.bp; two modules with the same name in Android.mk) would cause both to be built and installed. In many cases you only want either the host or target versions to be built/installed by default, and would be over-building with both. So PRODUCT_PACKAGES will be changing to just affect target modules, while PRODUCT_HOST_PACKAGES is being added for host modules.
Functional differences between PRODUCT_PACKAGES and PRODUCT_HOST_PACKAGES:
PRODUCT_HOST_PACKAGES does not have _ENG/_DEBUG variants, as that's a property of the target, not the host.PRODUCT_HOST_PACKAGES does not support LOCAL_MODULE_OVERRIDES.PRODUCT_HOST_PACKAGES requires listed modules to exist, and be host modules. (Unless ALLOW_MISSING_DEPENDENCIES is set)This is still an active migration, so currently it still uses PRODUCT_PACKAGES to make installation decisions, but verifies that if we used PRODUCT_HOST_PACKAGES, it would trigger installation for all of the same host packages. This check ignores shared libraries, as those are not normally necessary in PRODUCT_*PACKAGES, and tended to be over-built (especially the 32-bit variants).
Future changes will switch installation decisions to PRODUCT_HOST_PACKAGES for host modules, error when there's a host-only module in PRODUCT_PACKAGES, and do some further cleanup where LOCAL_REQUIRED_MODULES are still merged between host and target modules with the same name.
*.c.arm / *.cpp.arm deprecation {#file_arm}In Android.mk files, you used to be able to change LOCAL_ARM_MODE for each source file by appending .arm to the end of the filename in LOCAL_SRC_FILES.
Soong does not support this uncommonly used behavior, instead expecting those files to be split out into a separate static library that chooses arm over thumb for the entire library. This must now also be done in Android.mk files.
Modules that build for Windows (our only HOST_CROSS OS currently) must now be defined in Android.bp files.
LOCAL_MODULE_TAGS := eng debug are obsolete {#LOCAL_MODULE_TAGS}LOCAL_MODULE_TAGS value eng and debug are now obsolete. They allowed modules to specify that they should always be installed on -eng, or -eng and -userdebug builds. This conflicted with the ability for products to specify which modules should be installed, effectively making it impossible to build a stripped down product configuration that did not include those modules.
For the equivalent functionality, specify the modules in PRODUCT_PACKAGES_ENG or PRODUCT_PACKAGES_DEBUG in the appropriate product makefiles.
Core android packages like su got added to the list in build/make/target/product/base_system.mk, but for device-specific modules there are often better base product makefiles to use instead.
USER deprecation {#USER}USER will soon be nobody in many cases due to the addition of a sandbox around the Android build. Most of the time you shouldn't need to know the identity of the user running the build, but if you do, it's available in the make variable BUILD_USERNAME for now.
Similarly, the hostname tool will also be returning a more consistent value of android-build. The real value is available as BUILD_HOSTNAME.
BUILD_NUMBER removal from Android.mk {#BUILD_NUMBER}BUILD_NUMBER should not be used directly in Android.mk files, as it would trigger them to be re-read every time the BUILD_NUMBER changes (which it does on every build server build). If possible, just remove the use so that your builds are more reproducible. If you do need it, use BUILD_NUMBER_FROM_FILE:
$(LOCAL_BUILT_MODULE): mytool --build_number $(BUILD_NUMBER_FROM_FILE) -o $@
That will expand out to a subshell that will read the current BUILD_NUMBER whenever it's run. It will not re-run your command if the build number has changed, so incremental builds will have the build number from the last time the particular output was rebuilt.
DIST_DIR, dist_goal, and dist-for-goals {#dist}DIST_DIR and dist_goal are no longer available when reading Android.mk files (or other build tasks). Always use dist-for-goals instead, which takes a PHONY goal, and a list of files to copy to $DIST_DIR. Whenever dist is specified, and the goal would be built (either explicitly on the command line, or as a dependency of something on the command line), that file will be copied into $DIST_DIR. For example,
$(call dist-for-goals,foo,bar/baz)
will copy bar/baz into $DIST_DIR/baz when m foo dist is run.
Instead of specifying just a file, a destination name can be specified, including subdirectories:
$(call dist-for-goals,foo,bar/baz:logs/foo.log)
will copy bar/baz into $DIST_DIR/logs/foo.log when m foo dist is run.
.PHONY rule enforcement {#phony_targets}There are several new warnings/errors meant to ensure the proper use of .PHONY targets in order to improve the speed and reliability of incremental builds.
.PHONY-marked targets are often used as shortcuts to provide "friendly" names for real files to be built, but any target marked with .PHONY is also always considered dirty, needing to be rebuilt every build. This isn't a problem for aliases or one-off user-requested operations, but if real builds steps depend on a .PHONY target, it can get quite expensive for what should be a tiny build.
...mk:42: warning: PHONY target "out/.../foo" looks like a real file (contains a "/")
Between this warning and the next, we're requiring that .PHONY targets do not have "/" in them, and real file targets do have a "/". This makes it more obvious when reading makefiles what is happening, and will help the build system differentiate these in the future too.
...mk:42: warning: writing to readonly directory: "kernel-modules"
This warning will show up for one of two reasons:
.PHONY. This would be the case for this example.m clean is unable to clean the build, and future builds may not work properly....mk:42: warning: real file "out/.../foo" depends on PHONY target "buildbins"
If the first target isn't intended to be a real file, then it should be marked with .PHONY, which will satisfy this warning. This isn't the case for this example, as we require .PHONY targets not to have '/' in them.
If the second (PHONY) target is a real file, it may unnecessarily be marked with .PHONY.
.PHONY and calling other build systemsOne common pattern (mostly outside AOSP) that we've seen hit these warning is when building with external build systems (firmware, bootloader, kernel, etc). Those are often marked as .PHONY because the Android build system doesn't have enough dependencies to know when to run the other build system again during an incremental build.
We recommend to build these outside of Android, and deliver prebuilts into the Android tree instead of decreasing the speed and reliability of the incremental Android build.
In cases where that's not desired, to preserve the speed of Android incrementals, over-specifying dependencies is likely a better option than marking it with .PHONY:
out/target/.../zImage: $(sort $(shell find -L $(KERNEL_SRCDIR))) ...
For reliability, many of these other build systems do not guarantee the same level of incremental build assurances as the Android Build is attempting to do -- without custom checks, Make doesn't rebuild objects when CFLAGS change, etc. In order to fix this, our recommendation is to do clean builds for each of these external build systems every time anything they rely on changes. For relatively smaller builds (like the kernel), this may be reasonable as long as you're not trying to actively debug the kernel.
export and unexport deprecation {#export_keyword}The export and unexport keywords are obsolete, and will throw errors when used.
Device specific configuration should not be able to affect common core build steps -- we're looking at triggering build steps to be invalidated if the set of environment variables they can access changes. If device specific configuration is allowed to change those, switching devices with the same output directory could become significantly more expensive than it already can be.
If used during Android.mk files, and later tasks, it is increasingly likely that they are being used incorrectly. Attempting to change the environment for a single build step, and instead setting it for hundreds of thousands.
It is not recommended to just move the environment variable setting outside of the build (in vendorsetup.sh, or some other configuration script or wrapper). We expect to limit the environment variables that the build respects in the future, others will be cleared. (There will be methods to get custom variables into the build, just not to every build step)
Instead, write the export commands into the rule command lines themselves:
$(intermediates)/generated_output.img: rm -rf $@ export MY_ENV_A="$(MY_A)"; make ...
If you want to set many environment variables, and/or use them many times, write them out to a script and source the script:
envsh := $(intermediates)/env.sh $(envsh): rm -rf $@ echo 'export MY_ENV_A="$(MY_A)"' >$@ echo 'export MY_ENV_B="$(MY_B)"' >>$@ $(intermediates)/generated_output.img: PRIVATE_ENV := $(envsh) $(intermediates)/generated_output.img: $(envsh) a/b/c/package.sh rm -rf $@ source $(PRIVATE_ENV); make ... source $(PRIVATE_ENV); a/b/c/package.sh ...
Implicit rules look something like the following:
$(TARGET_OUT_SHARED_LIBRARIES)/%_vendor.so: $(TARGET_OUT_SHARED_LIBRARIES)/%.so ... %.o : %.foo ...
These can have wide ranging effects across unrelated modules, so they're now obsolete. Instead, use static pattern rules, which are similar, but explicitly match the specified outputs:
libs := $(foreach lib,libfoo libbar,$(TARGET_OUT_SHARED_LIBRARIES)/$(lib)_vendor.so) $(libs): %_vendor.so: %.so ... files := $(wildcard $(LOCAL_PATH)/*.foo) gen := $(patsubst $(LOCAL_PATH)/%.foo,$(intermediates)/%.o,$(files)) $(gen): %.o : %.foo ...
The build system uses module names in path names in many places. Having an extra '/' or '../' being inserted can cause problems -- and not just build breaks, but stranger invalid behavior.
In every case we've seen, the fix is relatively simple: move the directory into LOCAL_MODULE_RELATIVE_PATH (or LOCAL_MODULE_PATH if you're still using it). If this causes multiple modules to be named the same, use unique module names and LOCAL_MODULE_STEM to change the installed file name:
include $(CLEAR_VARS) LOCAL_MODULE := ver1/code.bin LOCAL_MODULE_PATH := $(TARGET_OUT_ETC)/firmware ... include $(BUILD_PREBUILT) include $(CLEAR_VARS) LOCAL_MODULE := ver2/code.bin LOCAL_MODULE_PATH := $(TARGET_OUT_ETC)/firmware ... include $(BUILD_PREBUILT)
Can be rewritten as:
include $(CLEAR_VARS) LOCAL_MODULE := ver1_code.bin LOCAL_MODULE_STEM := code.bin LOCAL_MODULE_PATH := $(TARGET_OUT_VENDOR)/firmware/ver1 ... include $(BUILD_PREBUILT) include $(CLEAR_VARS) LOCAL_MODULE := ver2_code.bin LOCAL_MODULE_STEM := code.bin LOCAL_MODULE_PATH := $(TARGET_OUT_VENDOR)/firmware/ver2 ... include $(BUILD_PREBUILT)
You just need to make sure that any other references (PRODUCT_PACKAGES, LOCAL_REQUIRED_MODULES, etc) are converted to the new names.
We've adopted lexical requirements very similar to Bazel's requirements for target names. Valid characters are a-z, A-Z, 0-9, and the special characters _.+-=,@~. This currently applies to LOCAL_PACKAGE_NAME, LOCAL_MODULE, and LOCAL_MODULE_SUFFIX, and LOCAL_MODULE_STEM*.
Many other characters already caused problems if you used them, so we don't expect this to have a large effect.
The build has started restricting the external host tools usable inside the build. This will help ensure that build results are reproducible across different machines, and catch mistakes before they become larger issues.
To start with, this includes replacing the $PATH with our own directory of tools, mirroring that of the host PATH. The only difference so far is the removal of the host GCC tools. Anything that is not explicitly in the configuration as allowed will continue functioning, but will generate a log message. This is expected to become more restrictive over time.
The configuration is located in build/soong/ui/build/paths/config.go, and contains all the common tools in use in many builds. Anything not in that list will currently print a warning in the $OUT_DIR/soong.log file, including the command and arguments used, and the process tree in order to help locate the usage.
In order to fix any issues brought up by these checks, the best way to fix them is to use tools checked into the tree -- either as prebuilts, or building them as host tools during the build.
As a temporary measure, you can set TEMPORARY_DISABLE_PATH_RESTRICTIONS=true in your environment to temporarily turn off the error checks and allow any tool to be used (with logging). Beware that GCC didn't work well with the interposer used for logging, so this may not help in all cases.
It is not required to source envsetup.sh before running a build. Many scripts, including a majority of our automated build systems, do not do so. Make will transparently make every environment variable available as a make variable. This means that relying on environment variables only set up in envsetup.sh will produce different output for local users and scripted users.
Many of these variables also include absolute path names, which we'd like to keep out of the generated files, so that you don't need to do a full rebuild if you move the source tree.
To fix this, we're marking the variables that are set in envsetup.sh as deprecated in the makefiles. This will trigger a warning every time one is read (or written) inside Kati. Once all the warnings have been removed for a particular variable, we'll switch it to obsolete, and any references will become errors.
| instead of | use |
|---|---|
| OUT {#OUT} | PRODUCT_OUT |
| ANDROID_HOST_OUT {#ANDROID_HOST_OUT} | HOST_OUT |
| ANDROID_PRODUCT_OUT {#ANDROID_PRODUCT_OUT} | PRODUCT_OUT |
| ANDROID_HOST_OUT_TESTCASES {#ANDROID_HOST_OUT_TESTCASES} | HOST_OUT_TESTCASES |
| ANDROID_TARGET_OUT_TESTCASES {#ANDROID_TARGET_OUT_TESTCASES} | TARGET_OUT_TESTCASES |
All of the make variables may be relative paths from the current directory, or absolute paths if the output directory was specified as an absolute path. If you need an absolute variable, convert it to absolute during a rule, so that it's not expanded into the generated ninja file:
$(PRODUCT_OUT)/gen.img: my/src/path/gen.sh export PRODUCT_OUT=$$(cd $(PRODUCT_OUT); pwd); cd my/src/path; ./gen.sh -o $${PRODUCT_OUT}/gen.img
In Android.mk files, you can always assume that the current directory is the root of the source tree, so this can just be replaced with '.' (which is what $TOP is hardcoded to), or removed entirely. If you need an absolute path, see the instructions above.
This isn't only set by envsetup.sh, but it is modified by it. Due to that it's rather easy for this to change between different shells, and it's not ideal to reread the makefiles every time this changes.
In most cases, you shouldn't need to touch PATH at all. When you need to have a rule reference a particular binary that's part of the source tree or outputs, it's preferrable to just use the path to the file itself (since you should already be adding that as a dependency).
Depending on the rule, passing the file path itself may not be feasible due to layers of unchangable scripts/binaries. In that case, be sure to add the dependency, but modify the PATH within the rule itself:
$(TARGET): myscript my/path/binary PATH=my/path:$$PATH myscript -o $@
Like PATH, this isn't only set by envsetup.sh, but it is modified by it. Due to that it's rather easy for this to change between different shells, and it's not ideal to reread the makefiles every time.
The best solution here is to start switching to Soong's python building support, which packages the python interpreter, libraries, and script all into one file that no longer needs PYTHONPATH. See fontchain_lint for examples of this:
If you still need to use PYTHONPATH, do so within the rule itself, just like path:
$(TARGET): myscript.py $(sort $(shell find my/python/lib -name '*.py')) PYTHONPATH=my/python/lib:$$PYTHONPATH myscript.py -o $@
Specify Framework Compatibility Matrix Version in device manifest by adding a target-level attribute to the root element <manifest>. If PRODUCT_COMPATIBILITY_MATRIX_LEVEL_OVERRIDE is 26 or 27, you can add "target-level"="1" to your device manifest instead.
Clang is the default and only supported Android compiler, so there is no reason for this option to exist.
These are all exported from envsetup.sh, but don't have clear equivalents within the makefile system. If you need one of them, you'll have to set up your own version.