EmbeddedPkg/SerialDxe/SerialIo.c

/** @file
  Serial IO Abstraction for GDB stub. This allows an EFI consoles that shows up on the system 
  running GDB. One consle for error information and another console for user input/output.
  
  Basic packet format is $packet-data#checksum. So every comand has 4 bytes of overhead: $, 
  #, 0, 0. The 0 and 0 are the ascii characters for the checksum. 
  

  Copyright (c) 2008 - 2009, Apple Inc. All rights reserved.<BR>
  
  This program and the accompanying materials
  are licensed and made available under the terms and conditions of the BSD License
  which accompanies this distribution.  The full text of the license may be found at
  http://opensource.org/licenses/bsd-license.php

  THE PROGRAM IS DISTRIBUTED UNDER THE BSD LICENSE ON AN "AS IS" BASIS,
  WITHOUT WARRANTIES OR REPRESENTATIONS OF ANY KIND, EITHER EXPRESS OR IMPLIED.

**/

#include <PiDxe.h>
#include <Library/UefiLib.h>
#include <Library/UefiBootServicesTableLib.h>
#include <Library/DebugLib.h>
#include <Library/SerialPortLib.h>
#include <Library/PcdLib.h>

#include <Protocol/SerialIo.h>

/**
  Reset the serial device.

  @param  This              Protocol instance pointer.
                            
  @retval EFI_SUCCESS       The device was reset.
  @retval EFI_DEVICE_ERROR  The serial device could not be reset.

**/
EFI_STATUS
EFIAPI
SerialReset (
  IN EFI_SERIAL_IO_PROTOCOL  *This
  )
{
  SerialPortInitialize ();
  return EFI_SUCCESS;
}


/**
  Sets the baud rate, receive FIFO depth, transmit/receice time out, parity, 
  data buts, and stop bits on a serial device.

  @param  This             Protocol instance pointer.
  @param  BaudRate         The requested baud rate. A BaudRate value of 0 will use the the
                           device's default interface speed.
  @param  ReveiveFifoDepth The requested depth of the FIFO on the receive side of the
                           serial interface. A ReceiveFifoDepth value of 0 will use
                           the device's dfault FIFO depth.
  @param  Timeout          The requested time out for a single character in microseconds.
                           This timeout applies to both the transmit and receive side of the
                           interface. A Timeout value of 0 will use the device's default time
                           out value.
  @param  Parity           The type of parity to use on this serial device. A Parity value of
                           DefaultParity will use the device's default parity value.
  @param  DataBits         The number of data bits to use on the serial device. A DataBits
                           vaule of 0 will use the device's default data bit setting.
  @param  StopBits         The number of stop bits to use on this serial device. A StopBits
                           value of DefaultStopBits will use the device's default number of
                           stop bits.

  @retval EFI_SUCCESS      The device was reset.
  @retval EFI_DEVICE_ERROR The serial device could not be reset.

**/
EFI_STATUS
EFIAPI
SerialSetAttributes (
  IN EFI_SERIAL_IO_PROTOCOL  *This,
  IN UINT64                  BaudRate,
  IN UINT32                  ReceiveFifoDepth,
  IN UINT32                  Timeout,
  IN EFI_PARITY_TYPE         Parity,
  IN UINT8                   DataBits,
  IN EFI_STOP_BITS_TYPE      StopBits
  )
{
  return EFI_UNSUPPORTED;
}


/**
  Set the control bits on a serial device

  @param  This             Protocol instance pointer.
  @param  Control          Set the bits of Control that are settable.

  @retval EFI_SUCCESS      The new control bits were set on the serial device.
  @retval EFI_UNSUPPORTED  The serial device does not support this operation.
  @retval EFI_DEVICE_ERROR The serial device is not functioning correctly.

**/
EFI_STATUS
EFIAPI
SerialSetControl (
  IN EFI_SERIAL_IO_PROTOCOL  *This,
  IN UINT32                  Control
  )
{
  return EFI_UNSUPPORTED;
}


/**
  Retrieves the status of thecontrol bits on a serial device

  @param  This              Protocol instance pointer.
  @param  Control           A pointer to return the current Control signals from the serial device.
                            
  @retval EFI_SUCCESS       The control bits were read from the serial device.
  @retval EFI_DEVICE_ERROR  The serial device is not functioning correctly.

**/
EFI_STATUS
EFIAPI
SerialGetControl (
  IN EFI_SERIAL_IO_PROTOCOL  *This,
  OUT UINT32                 *Control
  )
{
  if (SerialPortPoll ()) {
    // If a character is pending don't set EFI_SERIAL_INPUT_BUFFER_EMPTY
    *Control = EFI_SERIAL_OUTPUT_BUFFER_EMPTY;
  } else {
    *Control = EFI_SERIAL_INPUT_BUFFER_EMPTY | EFI_SERIAL_OUTPUT_BUFFER_EMPTY;
  }
  return EFI_SUCCESS;
}


/**
  Writes data to a serial device.

  @param  This              Protocol instance pointer.
  @param  BufferSize        On input, the size of the Buffer. On output, the amount of
                            data actually written.
  @param  Buffer            The buffer of data to write

  @retval EFI_SUCCESS       The data was written.
  @retval EFI_DEVICE_ERROR  The device reported an error.
  @retval EFI_TIMEOUT       The data write was stopped due to a timeout.

**/
EFI_STATUS
EFIAPI
SerialWrite (
  IN EFI_SERIAL_IO_PROTOCOL  *This,
  IN OUT UINTN               *BufferSize,
  IN VOID                    *Buffer
  )
{
  UINTN Count;
  
  Count = SerialPortWrite (Buffer, *BufferSize);
  *BufferSize = Count;
  return (Count == 0) ? EFI_DEVICE_ERROR : EFI_SUCCESS;
}

/**
  Writes data to a serial device.

  @param  This              Protocol instance pointer.
  @param  BufferSize        On input, the size of the Buffer. On output, the amount of
                            data returned in Buffer.
  @param  Buffer            The buffer to return the data into.

  @retval EFI_SUCCESS       The data was read.
  @retval EFI_DEVICE_ERROR  The device reported an error.
  @retval EFI_TIMEOUT       The data write was stopped due to a timeout.

**/

EFI_STATUS
EFIAPI
SerialRead (
  IN EFI_SERIAL_IO_PROTOCOL  *This,
  IN OUT UINTN               *BufferSize,
  OUT VOID                   *Buffer
  )
{
  UINTN Count;
  
  Count = SerialPortRead (Buffer, *BufferSize);
  *BufferSize = Count;
  return (Count == 0) ? EFI_DEVICE_ERROR : EFI_SUCCESS;
}


EFI_HANDLE  gHandle = NULL;

// 
// Template used to initailize the GDB Serial IO protocols
//
EFI_SERIAL_IO_MODE gSerialIoMode = {
  0,                                          // ControlMask
  0,                                          // Timeout
  FixedPcdGet64 (PcdUartDefaultBaudRate),     // BaudRate
  1,                                          // RceiveFifoDepth
  FixedPcdGet8 (PcdUartDefaultDataBits),      // DataBits
  FixedPcdGet8 (PcdUartDefaultParity),        // Parity
  FixedPcdGet8 (PcdUartDefaultStopBits)       // StopBits
};


EFI_SERIAL_IO_PROTOCOL gSerialIoTemplate = {
  SERIAL_IO_INTERFACE_REVISION,
  SerialReset,
  SerialSetAttributes,
  SerialSetControl,
  SerialGetControl,
  SerialWrite,
  SerialRead,
  &gSerialIoMode
};
  
typedef struct {
  VENDOR_DEVICE_PATH        Guid;
  UART_DEVICE_PATH          Uart;
  EFI_DEVICE_PATH_PROTOCOL  End;
} SIMPLE_TEXT_OUT_DEVICE_PATH;

SIMPLE_TEXT_OUT_DEVICE_PATH mDevicePath = {
  {
    { HARDWARE_DEVICE_PATH, HW_VENDOR_DP, sizeof (VENDOR_DEVICE_PATH), 0},
    EFI_CALLER_ID_GUID // Use the drivers GUID
  },
  {
    { END_DEVICE_PATH_TYPE, END_ENTIRE_DEVICE_PATH_SUBTYPE, sizeof (UART_DEVICE_PATH), 0},
    0,        // Reserved
    FixedPcdGet64 (PcdUartDefaultBaudRate),   // BaudRate
    FixedPcdGet8 (PcdUartDefaultDataBits),    // DataBits
    FixedPcdGet8 (PcdUartDefaultParity),      // Parity (N)
    FixedPcdGet8 (PcdUartDefaultStopBits)     // StopBits
  },
  { END_DEVICE_PATH_TYPE, END_ENTIRE_DEVICE_PATH_SUBTYPE, sizeof (EFI_DEVICE_PATH_PROTOCOL), 0}
};


/**
  Initialize the state information for the Serial Io Protocol

  @param  ImageHandle   of the loaded driver
  @param  SystemTable   Pointer to the System Table

  @retval EFI_SUCCESS           Protocol registered
  @retval EFI_OUT_OF_RESOURCES  Cannot allocate protocol data structure
  @retval EFI_DEVICE_ERROR      Hardware problems

**/
EFI_STATUS
EFIAPI
SerialDxeInitialize (
  IN EFI_HANDLE         ImageHandle,
  IN EFI_SYSTEM_TABLE   *SystemTable
  )
{
  EFI_STATUS      Status;


  // Make a new handle with Serial IO protocol and its device path on it.
  Status = gBS->InstallMultipleProtocolInterfaces (
                  &gHandle, 
                  &gEfiSerialIoProtocolGuid,   &gSerialIoTemplate,
                  &gEfiDevicePathProtocolGuid, &mDevicePath, 
                  NULL
                  );
  ASSERT_EFI_ERROR (Status);
  
  return Status;
}