Merge tag 'v4.17-rockchip-dts64-1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt
Pull "Rockchip dts64 changes for 4.17" from Heiko Stübner:
The rk3399 gained support its Cadence displayport controller and some
minor additions like pins for 2ch i2s0 and the cif test clocks as well
as a default rate for ACLK_VIO that should be 400MHz according to the TRM.
The rk3328 got uart dmas fixed - a non-critical fix, as nobody was using
that so far.
New boards are the rk3328-based roc-rk3328-cc, the rk3368-based Lion-SOM
+ baseborad from Theobroma Systems and a standalone variant of the Sapphire
board, as a lot of people where using that without the Exkavator baseboard.
Sapphire also saw a lot of small cleanups of things that are not part
of the actual Sapphire board, but the baseboard instead. The rk3399-puma
board got i2s and tsadc support and Gru got its DP node enabled.
* tag 'v4.17-rockchip-dts64-1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
arm64: dts: rockchip: remove keep-power-in-suspend from sdhci of rk3399-sapphire
arm64: dts: rockchip: assign clock rate for ACLK_VIO on rk3399
arm64: dts: rockchip: add a standalone version of the rk3399 sapphire
arm64: dts: rockchip: move rk3399-sapphire pwr_btn to daughterboard
arm64: dts: rockchip: move rk3399-sapphire i2s2 to daughterboard
arm64: dts: rockchip: move rk3399-sapphire sdio to excavator baseboard
arm64: dts: rockchip: enable I2S codec on rk3399-puma-haikou
arm64: dts: rockchip: move i2s0 node from baseboard to SoM on rk3399-puma
arm64: dts: rockchip: vdd_log on rk3399-sapphire is not an i2c slave
arm64: dts: rockchip: add Haikou baseboard with RK3368-uQ7 SoM
arm64: dts: rockchip: add RK3368-uQ7 (Lion) SoM
dt-bindings: add RK3368-uQ7 SoM and EVK base board
arm64: dts: rockchip: Fix RK3328 UART DMAs
arm64: dts: rockchip: enable DP for rk3399-gru
arm64: dts: rockchip: add cdn-dp node for rk3399.
arm64: dts: rockchip: add i2s0-2ch-bus pins on rk3399
arm64: dts: rockchip: enable tsadc on rk3399-puma
arm64: dts: rockchip: add roc-rk3328-cc board
arm64: dts: rockchip: Add cif test clocks for rk3399
diff --git a/Documentation/devicetree/bindings/arm/rockchip.txt b/Documentation/devicetree/bindings/arm/rockchip.txt
index 326d24b..1c1d62d 100644
--- a/Documentation/devicetree/bindings/arm/rockchip.txt
+++ b/Documentation/devicetree/bindings/arm/rockchip.txt
@@ -50,6 +50,10 @@
Required root node properties:
- compatible = "firefly,firefly-rk3399", "rockchip,rk3399";
+- Firefly roc-rk3328-cc board:
+ Required root node properties:
+ - compatible = "firefly,roc-rk3328-cc", "rockchip,rk3328";
+
- ChipSPARK PopMetal-RK3288 board:
Required root node properties:
- compatible = "chipspark,popmetal-rk3288", "rockchip,rk3288";
@@ -181,10 +185,18 @@
Required root node properties:
- compatible = "rockchip,rk3399-evb", "rockchip,rk3399";
+- Rockchip RK3399 Sapphire board standalone:
+ Required root node properties:
+ - compatible = "rockchip,rk3399-sapphire", "rockchip,rk3399";
+
- Rockchip RK3399 Sapphire Excavator board:
Required root node properties:
- compatible = "rockchip,rk3399-sapphire-excavator", "rockchip,rk3399";
+- Theobroma Systems RK3368-uQ7 Haikou Baseboard:
+ Required root node properties:
+ - compatible = "tsd,rk3368-uq7-haikou", "rockchip,rk3368";
+
- Theobroma Systems RK3399-Q7 Haikou Baseboard:
Required root node properties:
- compatible = "tsd,rk3399-q7-haikou", "rockchip,rk3399";
diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
index ce2701e..48a83f8 100644
--- a/arch/arm64/boot/dts/rockchip/Makefile
+++ b/arch/arm64/boot/dts/rockchip/Makefile
@@ -1,8 +1,10 @@
# SPDX-License-Identifier: GPL-2.0
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-evb.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-rock64.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-roc-cc.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3368-evb-act8846.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3368-geekbox.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3368-lion-haikou.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3368-orion-r68-meta.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3368-px5-evb.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3368-r88.dtb
@@ -10,4 +12,5 @@
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-firefly.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-gru-kevin.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-puma-haikou.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-sapphire.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-sapphire-excavator.dtb
diff --git a/arch/arm64/boot/dts/rockchip/rk3328-roc-cc.dts b/arch/arm64/boot/dts/rockchip/rk3328-roc-cc.dts
new file mode 100644
index 0000000..246c317
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3328-roc-cc.dts
@@ -0,0 +1,267 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2017 T-Chip Intelligent Technology Co., Ltd
+ */
+
+/dts-v1/;
+#include "rk3328.dtsi"
+
+/ {
+ model = "Firefly roc-rk3328-cc";
+ compatible = "firefly,roc-rk3328-cc", "rockchip,rk3328";
+
+ chosen {
+ stdout-path = "serial2:1500000n8";
+ };
+
+ gmac_clkin: external-gmac-clock {
+ compatible = "fixed-clock";
+ clock-frequency = <125000000>;
+ clock-output-names = "gmac_clkin";
+ #clock-cells = <0>;
+ };
+
+ dc_12v: dc-12v {
+ compatible = "regulator-fixed";
+ regulator-name = "dc_12v";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <12000000>;
+ regulator-max-microvolt = <12000000>;
+ };
+
+ vcc_sd: sdmmc-regulator {
+ compatible = "regulator-fixed";
+ gpio = <&gpio0 RK_PD6 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdmmc0m1_gpio>;
+ regulator-name = "vcc_sd";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vcc_io>;
+ };
+
+ vcc_host1_5v: vcc_otg_5v: vcc-host1-5v-regulator {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpio = <&gpio1 RK_PD2 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb20_host_drv>;
+ regulator-name = "vcc_host1_5v";
+ regulator-always-on;
+ vin-supply = <&vcc_sys>;
+ };
+
+ vcc_sys: vcc-sys {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_sys";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&dc_12v>;
+ };
+
+ vcc_phy: vcc-phy-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_phy";
+ regulator-always-on;
+ regulator-boot-on;
+ };
+};
+
+&cpu0 {
+ cpu-supply = <&vdd_arm>;
+};
+
+&emmc {
+ bus-width = <8>;
+ cap-mmc-highspeed;
+ non-removable;
+ pinctrl-names = "default";
+ pinctrl-0 = <&emmc_clk &emmc_cmd &emmc_bus8>;
+ status = "okay";
+};
+
+&gmac2io {
+ assigned-clocks = <&cru SCLK_MAC2IO>, <&cru SCLK_MAC2IO_EXT>;
+ assigned-clock-parents = <&gmac_clkin>, <&gmac_clkin>;
+ clock_in_out = "input";
+ phy-supply = <&vcc_phy>;
+ phy-mode = "rgmii";
+ pinctrl-names = "default";
+ pinctrl-0 = <&rgmiim1_pins>;
+ snps,reset-gpio = <&gpio1 RK_PC2 GPIO_ACTIVE_LOW>;
+ snps,reset-active-low;
+ snps,reset-delays-us = <0 10000 50000>;
+ tx_delay = <0x25>;
+ rx_delay = <0x11>;
+ status = "okay";
+};
+
+&i2c1 {
+ status = "okay";
+
+ rk805: pmic@18 {
+ compatible = "rockchip,rk805";
+ reg = <0x18>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <24 IRQ_TYPE_LEVEL_LOW>;
+ #clock-cells = <1>;
+ clock-output-names = "xin32k", "rk805-clkout2";
+ gpio-controller;
+ #gpio-cells = <2>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pmic_int_l>;
+ rockchip,system-power-controller;
+ wakeup-source;
+
+ vcc1-supply = <&vcc_sys>;
+ vcc2-supply = <&vcc_sys>;
+ vcc3-supply = <&vcc_sys>;
+ vcc4-supply = <&vcc_sys>;
+ vcc5-supply = <&vcc_io>;
+ vcc6-supply = <&vcc_io>;
+
+ regulators {
+ vdd_logic: DCDC_REG1 {
+ regulator-name = "vdd_logic";
+ regulator-min-microvolt = <712500>;
+ regulator-max-microvolt = <1450000>;
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1000000>;
+ };
+ };
+
+ vdd_arm: DCDC_REG2 {
+ regulator-name = "vdd_arm";
+ regulator-min-microvolt = <712500>;
+ regulator-max-microvolt = <1450000>;
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <950000>;
+ };
+ };
+
+ vcc_ddr: DCDC_REG3 {
+ regulator-name = "vcc_ddr";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ vcc_io: DCDC_REG4 {
+ regulator-name = "vcc_io";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <3300000>;
+ };
+ };
+
+ vcc_18: LDO_REG1 {
+ regulator-name = "vcc_18";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ vcc18_emmc: LDO_REG2 {
+ regulator-name = "vcc18_emmc";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ vdd_10: LDO_REG3 {
+ regulator-name = "vdd_10";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1000000>;
+ };
+ };
+ };
+ };
+};
+
+&pinctrl {
+ pmic {
+ pmic_int_l: pmic-int-l {
+ rockchip,pins = <1 RK_PD0 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+
+ usb2 {
+ usb20_host_drv: usb20-host-drv {
+ rockchip,pins = <1 RK_PD2 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+};
+
+&sdmmc {
+ bus-width = <4>;
+ cap-mmc-highspeed;
+ cap-sd-highspeed;
+ disable-wp;
+ max-frequency = <150000000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdmmc0_clk &sdmmc0_cmd &sdmmc0_dectn &sdmmc0_bus4>;
+ vmmc-supply = <&vcc_sd>;
+ status = "okay";
+};
+
+&tsadc {
+ status = "okay";
+};
+
+&u2phy {
+ status = "okay";
+};
+
+&u2phy_host {
+ status = "okay";
+};
+
+&u2phy_otg {
+ status = "okay";
+};
+
+&uart2 {
+ status = "okay";
+};
+
+&usb20_otg {
+ status = "okay";
+};
+
+&usb_host0_ehci {
+ status = "okay";
+};
+
+&usb_host0_ohci {
+ status = "okay";
+};
diff --git a/arch/arm64/boot/dts/rockchip/rk3328.dtsi b/arch/arm64/boot/dts/rockchip/rk3328.dtsi
index cae3415..be2bfbc 100644
--- a/arch/arm64/boot/dts/rockchip/rk3328.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3328.dtsi
@@ -318,7 +318,7 @@
clocks = <&cru SCLK_UART0>, <&cru PCLK_UART0>;
clock-names = "baudclk", "apb_pclk";
dmas = <&dmac 2>, <&dmac 3>;
- #dma-cells = <2>;
+ dma-names = "tx", "rx";
pinctrl-names = "default";
pinctrl-0 = <&uart0_xfer &uart0_cts &uart0_rts>;
reg-io-width = <4>;
@@ -333,7 +333,7 @@
clocks = <&cru SCLK_UART1>, <&cru PCLK_UART1>;
clock-names = "sclk_uart", "pclk_uart";
dmas = <&dmac 4>, <&dmac 5>;
- #dma-cells = <2>;
+ dma-names = "tx", "rx";
pinctrl-names = "default";
pinctrl-0 = <&uart1_xfer &uart1_cts &uart1_rts>;
reg-io-width = <4>;
@@ -348,7 +348,7 @@
clocks = <&cru SCLK_UART2>, <&cru PCLK_UART2>;
clock-names = "baudclk", "apb_pclk";
dmas = <&dmac 6>, <&dmac 7>;
- #dma-cells = <2>;
+ dma-names = "tx", "rx";
pinctrl-names = "default";
pinctrl-0 = <&uart2m1_xfer>;
reg-io-width = <4>;
diff --git a/arch/arm64/boot/dts/rockchip/rk3368-lion-haikou.dts b/arch/arm64/boot/dts/rockchip/rk3368-lion-haikou.dts
new file mode 100644
index 0000000..fca8e87
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3368-lion-haikou.dts
@@ -0,0 +1,146 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2018 Theobroma Systems Design und Consulting GmbH
+ */
+
+/dts-v1/;
+#include "rk3368-lion.dtsi"
+
+/ {
+ model = "Theobroma Systems RK3368-uQ7 Baseboard";
+ compatible = "tsd,rk3368-lion-haikou", "rockchip,rk3368";
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ i2cmux2 {
+ i2c@0 {
+ eeprom: eeprom@50 {
+ compatible = "atmel,24c01";
+ pagesize = <8>;
+ reg = <0x50>;
+ };
+ };
+ };
+
+ leds {
+ pinctrl-0 = <&led_pins_module>, <&led_sd_haikou>;
+
+ sd-card-led {
+ label = "sd_card_led";
+ gpios = <&gpio0 RK_PD2 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "mmc0";
+ };
+ };
+
+ dc_12v: dc-12v {
+ compatible = "regulator-fixed";
+ regulator-name = "dc_12v";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <12000000>;
+ regulator-max-microvolt = <12000000>;
+ };
+
+ vcc3v3_baseboard: vcc3v3-baseboard {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc3v3_baseboard";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&dc_12v>;
+ };
+
+ vcc5v0_otg: vcc5v0-otg-regulator {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpio = <&gpio0 RK_PD4 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&otg_vbus_drv>;
+ regulator-name = "vcc5v0_otg";
+ regulator-always-on;
+ };
+};
+
+&sdmmc {
+ bus-width = <4>;
+ cap-mmc-highspeed;
+ cap-sd-highspeed;
+ cd-gpios = <&gpio2 RK_PB3 GPIO_ACTIVE_LOW>;
+ disable-wp;
+ max-frequency = <25000000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_bus4>;
+ rockchip,default-sample-phase = <90>;
+ vmmc-supply = <&vcc3v3_baseboard>;
+ status = "okay";
+};
+
+&spi2 {
+ cs-gpios = <0>, <&gpio2 RK_PC3 GPIO_ACTIVE_LOW>;
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_xfer &uart0_cts &uart0_rts>;
+ status = "okay";
+};
+
+&usb_otg {
+ dr_mode = "otg";
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_xfer &uart0_cts &uart0_rts>;
+ status = "okay";
+};
+
+&uart1 {
+ /* alternate function of GPIO5/6 */
+ status = "disabled";
+};
+
+&pinctrl {
+ pinctrl-names = "default";
+ pinctrl-0 = <&haikou_pin_hog>;
+
+ hog {
+ haikou_pin_hog: haikou-pin-hog {
+ rockchip,pins =
+ /* LID_BTN */
+ <RK_GPIO3 RK_PA6 RK_FUNC_GPIO &pcfg_pull_up>,
+ /* BATLOW# */
+ <RK_GPIO0 RK_PD6 RK_FUNC_GPIO &pcfg_pull_up>,
+ /* SLP_BTN# */
+ <RK_GPIO3 RK_PA2 RK_FUNC_GPIO &pcfg_pull_up>,
+ /* BIOS_DISABLE# */
+ <RK_GPIO3 RK_PA0 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+
+ leds {
+ led_sd_haikou: led-sd-gpio {
+ rockchip,pins =
+ <RK_GPIO0 RK_PD2 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ sdmmc {
+ sdmmc_cd_gpio: sdmmc-cd-gpio {
+ rockchip,pins =
+ <RK_GPIO2 RK_PB3 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ usb_otg {
+ otg_vbus_drv: otg-vbus-drv {
+ rockchip,pins =
+ <RK_GPIO0 RK_PD4 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+};
diff --git a/arch/arm64/boot/dts/rockchip/rk3368-lion.dtsi b/arch/arm64/boot/dts/rockchip/rk3368-lion.dtsi
new file mode 100644
index 0000000..1315972
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3368-lion.dtsi
@@ -0,0 +1,317 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2018 Theobroma Systems Design und Consulting GmbH
+ */
+
+/dts-v1/;
+#include "rk3368.dtsi"
+
+/ {
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ ext_gmac: gmac-clk {
+ compatible = "fixed-clock";
+ clock-frequency = <125000000>;
+ clock-output-names = "ext_gmac";
+ #clock-cells = <0>;
+ };
+
+ i2cmux1 {
+ compatible = "i2c-mux-gpio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ i2c-parent = <&i2c1>;
+ mux-gpios = <&gpio1 RK_PA7 GPIO_ACTIVE_HIGH>;
+
+ /* Q7_GPO_I2C */
+ i2c@0 {
+ reg = <0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ /* Q7_SMB */
+ i2c@1 {
+ reg = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ };
+
+ i2cmux2 {
+ compatible = "i2c-mux-gpio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ i2c-parent = <&i2c2>;
+ mux-gpios = <&gpio1 RK_PB4 GPIO_ACTIVE_HIGH>;
+
+ /* Q7_LVDS_BLC_I2C */
+ i2c@0 {
+ reg = <0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ fan: fan@18 {
+ compatible = "ti,amc6821";
+ reg = <0x18>;
+ cooling-min-state = <0>;
+ cooling-max-state = <9>;
+ #cooling-cells = <2>;
+ };
+
+ rtc_twi: rtc@6f {
+ compatible = "isil,isl1208";
+ reg = <0x6f>;
+ };
+ };
+
+ /* Q7_GP2_I2C */
+ i2c@1 {
+ reg = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&led_pins_module>;
+
+ module_led1 {
+ label = "module_led1";
+ gpios = <&gpio2 RK_PB5 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ panic-indicator;
+ };
+
+ module_led2 {
+ label = "module_led2";
+ gpios = <&gpio3 RK_PA3 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ };
+
+ vcc_sys: vcc-sys-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_sys";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+};
+
+&cpu_l0 {
+ cpu-supply = <&vdd_cpu>;
+};
+
+&cpu_l1 {
+ cpu-supply = <&vdd_cpu>;
+};
+
+&cpu_l2 {
+ cpu-supply = <&vdd_cpu>;
+};
+
+&cpu_l3 {
+ cpu-supply = <&vdd_cpu>;
+};
+
+&cpu_b0 {
+ cpu-supply = <&vdd_cpu>;
+};
+
+&cpu_b1 {
+ cpu-supply = <&vdd_cpu>;
+};
+
+&cpu_b2 {
+ cpu-supply = <&vdd_cpu>;
+};
+
+&cpu_b3 {
+ cpu-supply = <&vdd_cpu>;
+};
+
+&emmc {
+ bus-width = <8>;
+ clock-frequency = <150000000>;
+ disable-wp;
+ mmc-hs200-1_8v;
+ non-removable;
+ vmmc-supply = <&vcc33_io>;
+ vqmmc-supply = <&vcc18_io>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&emmc_clk>, <&emmc_cmd>, <&emmc_bus8>;
+ status = "okay";
+};
+
+&gmac {
+ assigned-clocks = <&cru SCLK_MAC>;
+ assigned-clock-parents = <&ext_gmac>;
+ clock_in_out = "input";
+ phy-supply = <&vcc33_io>;
+ phy-mode = "rgmii";
+ pinctrl-names = "default";
+ pinctrl-0 = <&rgmii_pins>;
+ snps,reset-active-low;
+ snps,reset-delays-us = <0 10000 50000>;
+ snps,reset-gpio = <&gpio3 RK_PB3 GPIO_ACTIVE_HIGH>;
+ tx_delay = <0x10>;
+ rx_delay = <0x10>;
+ status = "okay";
+};
+
+&i2c0 {
+ status = "okay";
+
+ rk808: pmic@1b {
+ compatible = "rockchip,rk808";
+ reg = <0x1b>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <RK_PA5 IRQ_TYPE_LEVEL_LOW>;
+ clock-output-names = "xin32k", "rk808-clkout2";
+ #clock-cells = <1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pmic_int_l>, <&pmic_sleep>;
+ rockchip,system-power-controller;
+ vcc1-supply = <&vcc_sys>;
+ vcc2-supply = <&vcc_sys>;
+ vcc3-supply = <&vcc_sys>;
+ vcc4-supply = <&vcc_sys>;
+ vcc6-supply = <&vcc_sys>;
+ vcc7-supply = <&vcc_sys>;
+ vcc8-supply = <&vcc_sys>;
+ vcc9-supply = <&vcc_sys>;
+ vcc10-supply = <&vcc_sys>;
+ vcc11-supply = <&vcc_sys>;
+ vcc12-supply = <&vcc_sys>;
+
+ regulators {
+ vdd_cpu: DCDC_REG1 {
+ regulator-name = "vdd_cpu";
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ vdd_log: DCDC_REG2 {
+ regulator-name = "vdd_log";
+ regulator-min-microvolt = <700000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ vcc_ddr: DCDC_REG3 {
+ regulator-name = "vcc_ddr";
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ vcc33_io: DCDC_REG4 {
+ regulator-name = "vcc33_io";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ vcc33_video: LDO_REG2 {
+ regulator-name = "vcc33_video";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ vdd10_pll: LDO_REG3 {
+ regulator-name = "vdd10_pll";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ vcc18_io: LDO_REG4 {
+ regulator-name = "vcc18_io";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ };
+
+ vdd10_video: LDO_REG6 {
+ regulator-name = "vdd10_video";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ vcc18_video: LDO_REG8 {
+ regulator-name = "vcc18_video";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+ };
+ };
+};
+
+&i2c1 {
+ status = "okay";
+};
+
+&i2c2 {
+ status = "okay";
+};
+
+&pinctrl {
+ leds {
+ led_pins_module: led-module-gpio {
+ rockchip,pins =
+ <RK_GPIO2 RK_PB5 RK_FUNC_GPIO &pcfg_pull_none>,
+ <RK_GPIO3 RK_PA3 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+ pmic {
+ pmic_int_l: pmic-int-l {
+ rockchip,pins = <RK_GPIO0 RK_PA5 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+
+ pmic_sleep: pmic-sleep {
+ rockchip,pins = <RK_GPIO0 RK_PA0 RK_FUNC_2 &pcfg_pull_none>;
+ };
+ };
+};
+
+&spi1 {
+ status = "okay";
+
+ norflash: flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <50000000>;
+ };
+};
+
+&uart1 {
+ status = "okay";
+};
+
+&uart3 {
+ status = "okay";
+};
+
+&usb_host0_ehci {
+ status = "okay";
+};
+
+&wdt {
+ status = "okay";
+};
diff --git a/arch/arm64/boot/dts/rockchip/rk3399-gru.dtsi b/arch/arm64/boot/dts/rockchip/rk3399-gru.dtsi
index 03f1950..300f11d 100644
--- a/arch/arm64/boot/dts/rockchip/rk3399-gru.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3399-gru.dtsi
@@ -515,10 +515,15 @@
compatible = "rockchip,rk3399-gru-sound";
rockchip,cpu = <&i2s0 &i2s2>;
rockchip,codec = <&max98357a &headsetcodec
- &codec &wacky_spi_audio>;
+ &codec &wacky_spi_audio &cdn_dp>;
};
};
+&cdn_dp {
+ status = "okay";
+ extcon = <&usbc_extcon0>, <&usbc_extcon1>;
+};
+
/*
* Set some suspend operating points to avoid OVP in suspend
*
@@ -581,7 +586,8 @@
<&cru PCLK_PERIHP>,
<&cru ACLK_PERILP0>, <&cru HCLK_PERILP0>,
<&cru PCLK_PERILP0>, <&cru ACLK_CCI>,
- <&cru HCLK_PERILP1>, <&cru PCLK_PERILP1>;
+ <&cru HCLK_PERILP1>, <&cru PCLK_PERILP1>,
+ <&cru ACLK_VIO>;
assigned-clock-rates =
<600000000>, <800000000>,
<1000000000>,
@@ -589,7 +595,8 @@
<37500000>,
<100000000>, <100000000>,
<50000000>, <800000000>,
- <100000000>, <50000000>;
+ <100000000>, <50000000>,
+ <400000000>;
};
&emmc_phy {
diff --git a/arch/arm64/boot/dts/rockchip/rk3399-puma-haikou.dts b/arch/arm64/boot/dts/rockchip/rk3399-puma-haikou.dts
index 9a74860..7d3e8bf 100644
--- a/arch/arm64/boot/dts/rockchip/rk3399-puma-haikou.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3399-puma-haikou.dts
@@ -61,6 +61,30 @@
};
};
+ i2s0-sound {
+ compatible = "simple-audio-card";
+ simple-audio-card,format = "i2s";
+ simple-audio-card,name = "Haikou,I2S-codec";
+ simple-audio-card,mclk-fs = <512>;
+
+ simple-audio-card,codec {
+ clocks = <&sgtl5000_clk>;
+ sound-dai = <&sgtl5000>;
+ };
+
+ simple-audio-card,cpu {
+ bitclock-master;
+ frame-master;
+ sound-dai = <&i2s0>;
+ };
+ };
+
+ sgtl5000_clk: sgtl5000-oscillator {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <24576000>;
+ };
+
dc_12v: dc-12v {
compatible = "regulator-fixed";
regulator-name = "dc_12v";
@@ -80,6 +104,16 @@
vin-supply = <&dc_12v>;
};
+ vcc5v0_baseboard: vcc5v0-baseboard {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc5v0_baseboard";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&dc_12v>;
+ };
+
vcc5v0_otg: vcc5v0-otg-regulator {
compatible = "regulator-fixed";
enable-active-high;
@@ -89,6 +123,24 @@
regulator-name = "vcc5v0_otg";
regulator-always-on;
};
+
+ vdda_codec: vdda-codec {
+ compatible = "regulator-fixed";
+ regulator-name = "vdda_codec";
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vcc5v0_baseboard>;
+ };
+
+ vddd_codec: vddd-codec {
+ compatible = "regulator-fixed";
+ regulator-name = "vddd_codec";
+ regulator-boot-on;
+ regulator-min-microvolt = <1600000>;
+ regulator-max-microvolt = <1600000>;
+ vin-supply = <&vcc5v0_baseboard>;
+ };
};
&i2c1 {
@@ -110,6 +162,17 @@
&i2c4 {
status = "okay";
clock-frequency = <400000>;
+
+ sgtl5000: codec@0a {
+ compatible = "fsl,sgtl5000";
+ reg = <0x0a>;
+ clocks = <&sgtl5000_clk>;
+ #sound-dai-cells = <0>;
+ VDDA-supply = <&vdda_codec>;
+ VDDIO-supply = <&vdda_codec>;
+ VDDD-supply = <&vddd_codec>;
+ status = "okay";
+ };
};
&i2c6 {
@@ -117,14 +180,6 @@
clock-frequency = <400000>;
};
-&i2s0 {
- status = "okay";
- rockchip,playback-channels = <8>;
- rockchip,capture-channels = <8>;
- #sound-dai-cells = <0>;
- status = "okay";
-};
-
&pcie_phy {
status = "okay";
};
diff --git a/arch/arm64/boot/dts/rockchip/rk3399-puma.dtsi b/arch/arm64/boot/dts/rockchip/rk3399-puma.dtsi
index 1fc5060..4a2d06a 100644
--- a/arch/arm64/boot/dts/rockchip/rk3399-puma.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3399-puma.dtsi
@@ -435,6 +435,28 @@
};
};
+&i2s0 {
+ pinctrl-0 = <&i2s0_2ch_bus>;
+ rockchip,playback-channels = <2>;
+ rockchip,capture-channels = <2>;
+ #sound-dai-cells = <0>;
+ status = "okay";
+};
+
+/*
+ * As Q7 does not specify neither a global nor a RX clock for I2S these
+ * signals are not used. Furthermore I2S0_LRCK_RX is used as GPIO.
+ * Therefore we have to redefine the i2s0_2ch_bus definition to prevent
+ * conflicts.
+ */
+&i2s0_2ch_bus {
+ rockchip,pins =
+ <RK_GPIO3 RK_PD0 RK_FUNC_1 &pcfg_pull_none>,
+ <RK_GPIO3 RK_PD2 RK_FUNC_1 &pcfg_pull_none>,
+ <RK_GPIO3 RK_PD3 RK_FUNC_1 &pcfg_pull_none>,
+ <RK_GPIO3 RK_PD7 RK_FUNC_1 &pcfg_pull_none>;
+};
+
&io_domains {
status = "okay";
bt656-supply = <&vcc_1v8>;
@@ -505,6 +527,12 @@
};
};
+&tsadc {
+ rockchip,hw-tshut-mode = <1>;
+ rockchip,hw-tshut-polarity = <1>;
+ status = "okay";
+};
+
&u2phy1 {
status = "okay";
diff --git a/arch/arm64/boot/dts/rockchip/rk3399-sapphire-excavator.dts b/arch/arm64/boot/dts/rockchip/rk3399-sapphire-excavator.dts
index b7bd88f..56952d1 100644
--- a/arch/arm64/boot/dts/rockchip/rk3399-sapphire-excavator.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3399-sapphire-excavator.dts
@@ -41,7 +41,6 @@
*/
/dts-v1/;
-#include <dt-bindings/input/input.h>
#include "rk3399-sapphire.dtsi"
/ {
@@ -95,22 +94,6 @@
};
};
- keys: gpio-keys {
- compatible = "gpio-keys";
- autorepeat;
-
- power {
- debounce-interval = <100>;
- gpios = <&gpio0 RK_PA5 GPIO_ACTIVE_LOW>;
- label = "GPIO Power";
- linux,code = <KEY_POWER>;
- linux,input-type = <1>;
- pinctrl-names = "default";
- pinctrl-0 = <&pwr_btn>;
- wakeup-source;
- };
- };
-
rt5651-sound {
compatible = "simple-audio-card";
simple-audio-card,name = "realtek,rt5651-codec";
@@ -207,18 +190,7 @@
status = "okay";
};
-&i2s2 {
- #sound-dai-cells = <0>;
- status = "okay";
-};
-
&pinctrl {
- buttons {
- pwr_btn: pwr-btn {
- rockchip,pins = <0 RK_PA5 RK_FUNC_GPIO &pcfg_pull_up>;
- };
- };
-
sdio-pwrseq {
wifi_enable_h: wifi-enable-h {
rockchip,pins = <0 RK_PB2 RK_FUNC_GPIO &pcfg_pull_none>;
@@ -232,6 +204,22 @@
};
};
+&sdio0 {
+ bus-width = <4>;
+ cap-sd-highspeed;
+ cap-sdio-irq;
+ clock-frequency = <50000000>;
+ disable-wp;
+ keep-power-in-suspend;
+ max-frequency = <50000000>;
+ mmc-pwrseq = <&sdio_pwrseq>;
+ non-removable;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdio0_bus4 &sdio0_cmd &sdio0_clk>;
+ sd-uhs-sdr104;
+ status = "okay";
+};
+
&spdif {
i2c-scl-rising-time-ns = <450>;
i2c-scl-falling-time-ns = <15>;
diff --git a/arch/arm64/boot/dts/rockchip/rk3399-sapphire.dts b/arch/arm64/boot/dts/rockchip/rk3399-sapphire.dts
new file mode 100644
index 0000000..5a58060
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3399-sapphire.dts
@@ -0,0 +1,12 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2018 Fuzhou Rockchip Electronics Co., Ltd.
+ */
+
+/dts-v1/;
+#include "rk3399-sapphire.dtsi"
+
+/ {
+ model = "Sapphire-RK3399 Board";
+ compatible = "rockchip,rk3399-sapphire", "rockchip,rk3399";
+};
diff --git a/arch/arm64/boot/dts/rockchip/rk3399-sapphire.dtsi b/arch/arm64/boot/dts/rockchip/rk3399-sapphire.dtsi
index ce592a4..e5daed7 100644
--- a/arch/arm64/boot/dts/rockchip/rk3399-sapphire.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3399-sapphire.dtsi
@@ -41,6 +41,7 @@
*/
#include "dt-bindings/pwm/pwm.h"
+#include "dt-bindings/input/input.h"
#include "rk3399.dtsi"
#include "rk3399-opp.dtsi"
@@ -102,6 +103,22 @@
regulator-max-microvolt = <12000000>;
};
+ keys: gpio-keys {
+ compatible = "gpio-keys";
+ autorepeat;
+
+ power {
+ debounce-interval = <100>;
+ gpios = <&gpio0 RK_PA5 GPIO_ACTIVE_LOW>;
+ label = "GPIO Power";
+ linux,code = <KEY_POWER>;
+ linux,input-type = <1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwr_btn>;
+ wakeup-source;
+ };
+ };
+
/* switched by pmic_sleep */
vcc1v8_s3: vcca1v8_s3: vcc1v8-s3 {
compatible = "regulator-fixed";
@@ -143,6 +160,17 @@
regulator-always-on;
vin-supply = <&vcc_sys>;
};
+
+ vdd_log: vdd-log {
+ compatible = "pwm-regulator";
+ pwms = <&pwm2 0 25000 1>;
+ regulator-name = "vdd_log";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1400000>;
+ vin-supply = <&vcc_sys>;
+ };
};
&cpu_l0 {
@@ -421,17 +449,6 @@
regulator-off-in-suspend;
};
};
-
- vdd_log: vdd-log {
- compatible = "pwm-regulator";
- pwms = <&pwm2 0 25000 1>;
- regulator-name = "vdd_log";
- regulator-always-on;
- regulator-boot-on;
- regulator-min-microvolt = <800000>;
- regulator-max-microvolt = <1400000>;
- vin-supply = <&vcc_sys>;
- };
};
&i2c3 {
@@ -440,6 +457,11 @@
status = "okay";
};
+&i2s2 {
+ #sound-dai-cells = <0>;
+ status = "okay";
+};
+
&io_domains {
status = "okay";
@@ -470,6 +492,12 @@
};
&pinctrl {
+ buttons {
+ pwr_btn: pwr-btn {
+ rockchip,pins = <0 RK_PA5 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+
pmic {
pmic_int_l: pmic-int-l {
rockchip,pins =
@@ -513,29 +541,12 @@
&sdhci {
bus-width = <8>;
- keep-power-in-suspend;
mmc-hs400-1_8v;
mmc-hs400-enhanced-strobe;
non-removable;
status = "okay";
};
-&sdio0 {
- bus-width = <4>;
- cap-sd-highspeed;
- cap-sdio-irq;
- clock-frequency = <50000000>;
- disable-wp;
- keep-power-in-suspend;
- max-frequency = <50000000>;
- mmc-pwrseq = <&sdio_pwrseq>;
- non-removable;
- pinctrl-names = "default";
- pinctrl-0 = <&sdio0_bus4 &sdio0_cmd &sdio0_clk>;
- sd-uhs-sdr104;
- status = "okay";
-};
-
&sdmmc {
bus-width = <4>;
cap-mmc-highspeed;
diff --git a/arch/arm64/boot/dts/rockchip/rk3399.dtsi b/arch/arm64/boot/dts/rockchip/rk3399.dtsi
index 2605118..e5491d6 100644
--- a/arch/arm64/boot/dts/rockchip/rk3399.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3399.dtsi
@@ -457,6 +457,42 @@
};
};
+ cdn_dp: dp@fec00000 {
+ compatible = "rockchip,rk3399-cdn-dp";
+ reg = <0x0 0xfec00000 0x0 0x100000>;
+ interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH 0>;
+ assigned-clocks = <&cru SCLK_DP_CORE>;
+ assigned-clock-rates = <100000000>;
+ clocks = <&cru SCLK_DP_CORE>, <&cru PCLK_DP_CTRL>,
+ <&cru SCLK_SPDIF_REC_DPTX>, <&cru PCLK_VIO_GRF>;
+ clock-names = "core-clk", "pclk", "spdif", "grf";
+ phys = <&tcphy0_dp>, <&tcphy1_dp>;
+ power-domains = <&power RK3399_PD_HDCP>;
+ resets = <&cru SRST_DPTX_SPDIF_REC>, <&cru SRST_P_UPHY0_DPTX>,
+ <&cru SRST_P_UPHY0_APB>, <&cru SRST_DP_CORE>;
+ reset-names = "spdif", "dptx", "apb", "core";
+ rockchip,grf = <&grf>;
+ #sound-dai-cells = <1>;
+ status = "disabled";
+
+ ports {
+ dp_in: port {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ dp_in_vopb: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&vopb_out_dp>;
+ };
+
+ dp_in_vopl: endpoint@1 {
+ reg = <1>;
+ remote-endpoint = <&vopl_out_dp>;
+ };
+ };
+ };
+ };
+
gic: interrupt-controller@fee00000 {
compatible = "arm,gic-v3";
#interrupt-cells = <4>;
@@ -1286,7 +1322,8 @@
<&cru PCLK_PERIHP>,
<&cru ACLK_PERILP0>, <&cru HCLK_PERILP0>,
<&cru PCLK_PERILP0>, <&cru ACLK_CCI>,
- <&cru HCLK_PERILP1>, <&cru PCLK_PERILP1>;
+ <&cru HCLK_PERILP1>, <&cru PCLK_PERILP1>,
+ <&cru ACLK_VIO>;
assigned-clock-rates =
<594000000>, <800000000>,
<1000000000>,
@@ -1294,7 +1331,8 @@
<37500000>,
<100000000>, <100000000>,
<50000000>, <600000000>,
- <100000000>, <50000000>;
+ <100000000>, <50000000>,
+ <400000000>;
};
grf: syscon@ff770000 {
@@ -1547,6 +1585,11 @@
reg = <3>;
remote-endpoint = <&mipi1_in_vopl>;
};
+
+ vopl_out_dp: endpoint@4 {
+ reg = <4>;
+ remote-endpoint = <&dp_in_vopl>;
+ };
};
};
@@ -1599,6 +1642,11 @@
reg = <3>;
remote-endpoint = <&mipi1_in_vopb>;
};
+
+ vopb_out_dp: endpoint@4 {
+ reg = <4>;
+ remote-endpoint = <&dp_in_vopb>;
+ };
};
};
@@ -2043,6 +2091,16 @@
};
i2s0 {
+ i2s0_2ch_bus: i2s0-2ch-bus {
+ rockchip,pins =
+ <3 24 RK_FUNC_1 &pcfg_pull_none>,
+ <3 25 RK_FUNC_1 &pcfg_pull_none>,
+ <3 26 RK_FUNC_1 &pcfg_pull_none>,
+ <3 27 RK_FUNC_1 &pcfg_pull_none>,
+ <3 31 RK_FUNC_1 &pcfg_pull_none>,
+ <4 0 RK_FUNC_1 &pcfg_pull_none>;
+ };
+
i2s0_8ch_bus: i2s0-8ch-bus {
rockchip,pins =
<3 24 RK_FUNC_1 &pcfg_pull_none>,
@@ -2293,6 +2351,23 @@
};
};
+ testclk {
+ test_clkout0: test-clkout0 {
+ rockchip,pins =
+ <0 0 RK_FUNC_1 &pcfg_pull_none>;
+ };
+
+ test_clkout1: test-clkout1 {
+ rockchip,pins =
+ <2 25 RK_FUNC_2 &pcfg_pull_none>;
+ };
+
+ test_clkout2: test-clkout2 {
+ rockchip,pins =
+ <0 8 RK_FUNC_3 &pcfg_pull_none>;
+ };
+ };
+
tsadc {
otp_gpio: otp-gpio {
rockchip,pins = <1 6 RK_FUNC_GPIO &pcfg_pull_none>;