pata_ninja32: suspend/resume support
I had assumed that the standard recovery would be sufficient for this
hardware but it isn't. Fix up the other registers on resume as needed. See
bug #11735
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
diff --git a/drivers/ata/pata_ninja32.c b/drivers/ata/pata_ninja32.c
index 5e76f96..4e466ea 100644
--- a/drivers/ata/pata_ninja32.c
+++ b/drivers/ata/pata_ninja32.c
@@ -44,7 +44,7 @@
#include <linux/libata.h>
#define DRV_NAME "pata_ninja32"
-#define DRV_VERSION "0.0.1"
+#define DRV_VERSION "0.1.1"
/**
@@ -88,6 +88,17 @@
.set_piomode = ninja32_set_piomode,
};
+static void ninja32_program(void __iomem *base)
+{
+ iowrite8(0x05, base + 0x01); /* Enable interrupt lines */
+ iowrite8(0xBE, base + 0x02); /* Burst, ?? setup */
+ iowrite8(0x01, base + 0x03); /* Unknown */
+ iowrite8(0x20, base + 0x04); /* WAIT0 */
+ iowrite8(0x8f, base + 0x05); /* Unknown */
+ iowrite8(0xa4, base + 0x1c); /* Unknown */
+ iowrite8(0x83, base + 0x1d); /* BMDMA control: WAIT0 */
+}
+
static int ninja32_init_one(struct pci_dev *dev, const struct pci_device_id *id)
{
struct ata_host *host;
@@ -133,18 +144,28 @@
ap->ioaddr.bmdma_addr = base;
ata_sff_std_ports(&ap->ioaddr);
- iowrite8(0x05, base + 0x01); /* Enable interrupt lines */
- iowrite8(0xBE, base + 0x02); /* Burst, ?? setup */
- iowrite8(0x01, base + 0x03); /* Unknown */
- iowrite8(0x20, base + 0x04); /* WAIT0 */
- iowrite8(0x8f, base + 0x05); /* Unknown */
- iowrite8(0xa4, base + 0x1c); /* Unknown */
- iowrite8(0x83, base + 0x1d); /* BMDMA control: WAIT0 */
+ ninja32_program(base);
/* FIXME: Should we disable them at remove ? */
return ata_host_activate(host, dev->irq, ata_sff_interrupt,
IRQF_SHARED, &ninja32_sht);
}
+#ifdef CONFIG_PM
+
+static int ninja32_reinit_one(struct pci_dev *pdev)
+{
+ struct ata_host *host = dev_get_drvdata(&pdev->dev);
+ int rc;
+
+ rc = ata_pci_device_do_resume(pdev);
+ if (rc)
+ return rc;
+ ninja32_program(host->iomap[0]);
+ ata_host_resume(host);
+ return 0;
+}
+#endif
+
static const struct pci_device_id ninja32[] = {
{ 0x1145, 0xf021, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0 },
{ 0x1145, 0xf024, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0 },
@@ -155,7 +176,11 @@
.name = DRV_NAME,
.id_table = ninja32,
.probe = ninja32_init_one,
- .remove = ata_pci_remove_one
+ .remove = ata_pci_remove_one,
+#ifdef CONFIG_PM
+ .suspend = ata_pci_device_suspend,
+ .resume = ninja32_reinit_one,
+#endif
};
static int __init ninja32_init(void)