ARM: mvebu: Add Armada 385 Access Point Development Board support
The A385-AP is a board produced by Marvell that holds 3 mPCIe slot, a 16MB
SPI-NOR, 3 Gigabit Ethernet ports, USB3 and NAND flash storage.
[gregory.clement@free-electrons.com: switch the license to the dual
X11/GPL with the agreement of the author]
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
diff --git a/arch/arm/boot/dts/armada-385-db-ap.dts b/arch/arm/boot/dts/armada-385-db-ap.dts
new file mode 100644
index 0000000..57b9119
--- /dev/null
+++ b/arch/arm/boot/dts/armada-385-db-ap.dts
@@ -0,0 +1,178 @@
+/*
+ * Device Tree file for Marvell Armada 385 Access Point Development board
+ * (DB-88F6820-AP)
+ *
+ * Copyright (C) 2014 Marvell
+ *
+ * Nadav Haklai <nadavh@marvell.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without
+ * any warranty of any kind, whether express or implied.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "armada-385.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+ model = "Marvell Armada 385 Access Point Development Board";
+ compatible = "marvell,a385-db-ap", "marvell,armada385", "marvell,armada38x";
+
+ chosen {
+ bootargs = "console=ttyS0,115200";
+ stdout-path = &uart1;
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0x00000000 0x80000000>; /* 2GB */
+ };
+
+ soc {
+ ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000
+ MBUS_ID(0x01, 0x1d) 0 0xfff00000 0x100000>;
+
+ internal-regs {
+ spi1: spi@10680 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi1_pins>;
+ status = "okay";
+
+ spi-flash@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "st,m25p128";
+ reg = <0>; /* Chip select 0 */
+ spi-max-frequency = <54000000>;
+ };
+ };
+
+ i2c0: i2c@11000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins>;
+ status = "okay";
+
+ /*
+ * This bus is wired to two EEPROM
+ * sockets, one of which holding the
+ * board ID used by the bootloader.
+ * Erasing this EEPROM's content will
+ * brick the board.
+ * Use this bus with caution.
+ */
+ };
+
+ mdio@72004 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mdio_pins>;
+
+ phy0: ethernet-phy@1 {
+ reg = <1>;
+ };
+
+ phy1: ethernet-phy@4 {
+ reg = <4>;
+ };
+
+ phy2: ethernet-phy@6 {
+ reg = <6>;
+ };
+ };
+
+ /* UART0 is exposed through the JP8 connector */
+ uart0: serial@12000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins>;
+ status = "okay";
+ };
+
+ /*
+ * UART1 is exposed through a FTDI chip
+ * wired to the mini-USB connector
+ */
+ uart1: serial@12100 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pins>;
+ status = "okay";
+ };
+
+ ethernet@30000 {
+ status = "okay";
+ phy = <&phy2>;
+ phy-mode = "sgmii";
+ };
+
+ ethernet@34000 {
+ status = "okay";
+ phy = <&phy1>;
+ phy-mode = "sgmii";
+ };
+
+ ethernet@70000 {
+ pinctrl-names = "default";
+
+ /*
+ * The Reference Clock 0 is used to
+ * provide a clock to the PHY
+ */
+ pinctrl-0 = <&ge0_rgmii_pins>, <&ref_clk0_pins>;
+ status = "okay";
+ phy = <&phy0>;
+ phy-mode = "rgmii-id";
+ };
+ };
+
+ pcie-controller {
+ status = "okay";
+
+ /*
+ * The three PCIe units are accessible through
+ * standard mini-PCIe slots on the board.
+ */
+ pcie@1,0 {
+ /* Port 0, Lane 0 */
+ status = "okay";
+ };
+
+ pcie@2,0 {
+ /* Port 1, Lane 0 */
+ status = "okay";
+ };
+
+ pcie@3,0 {
+ /* Port 2, Lane 0 */
+ status = "okay";
+ };
+ };
+ };
+};