efi/x86: Don't relocate the kernel unless necessary
Add alignment slack to the PE image size, so that we can realign the
decompression buffer within the space allocated for the image.
Only relocate the kernel if it has been loaded at an unsuitable address:
- Below LOAD_PHYSICAL_ADDR, or
- Above 64T for 64-bit and 512MiB for 32-bit
For 32-bit, the upper limit is conservative, but the exact limit can be
difficult to calculate.
Signed-off-by: Arvind Sankar <nivedita@alum.mit.edu>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20200303221205.4048668-6-nivedita@alum.mit.edu
Link: https://lore.kernel.org/r/20200308080859.21568-20-ardb@kernel.org
diff --git a/drivers/firmware/efi/libstub/x86-stub.c b/drivers/firmware/efi/libstub/x86-stub.c
index 3e1bc8a..4615d29 100644
--- a/drivers/firmware/efi/libstub/x86-stub.c
+++ b/drivers/firmware/efi/libstub/x86-stub.c
@@ -17,6 +17,9 @@
#include "efistub.h"
+/* Maximum physical address for 64-bit kernel with 4-level paging */
+#define MAXMEM_X86_64_4LEVEL (1ull << 46)
+
static efi_system_table_t *sys_table;
extern const bool efi_is64;
extern u32 image_offset;
@@ -718,6 +721,7 @@ unsigned long efi_main(efi_handle_t handle,
struct boot_params *boot_params)
{
unsigned long bzimage_addr = (unsigned long)startup_32;
+ unsigned long buffer_start, buffer_end;
struct setup_header *hdr = &boot_params->hdr;
efi_status_t status;
unsigned long cmdline_paddr;
@@ -729,10 +733,33 @@ unsigned long efi_main(efi_handle_t handle,
efi_exit(handle, EFI_INVALID_PARAMETER);
/*
- * If the kernel isn't already loaded at the preferred load
- * address, relocate it.
+ * If the kernel isn't already loaded at a suitable address,
+ * relocate it.
+ *
+ * It must be loaded above LOAD_PHYSICAL_ADDR.
+ *
+ * The maximum address for 64-bit is 1 << 46 for 4-level paging. This
+ * is defined as the macro MAXMEM, but unfortunately that is not a
+ * compile-time constant if 5-level paging is configured, so we instead
+ * define our own macro for use here.
+ *
+ * For 32-bit, the maximum address is complicated to figure out, for
+ * now use KERNEL_IMAGE_SIZE, which will be 512MiB, the same as what
+ * KASLR uses.
+ *
+ * Also relocate it if image_offset is zero, i.e. we weren't loaded by
+ * LoadImage, but we are not aligned correctly.
*/
- if (bzimage_addr - image_offset != hdr->pref_address) {
+
+ buffer_start = ALIGN(bzimage_addr - image_offset,
+ hdr->kernel_alignment);
+ buffer_end = buffer_start + hdr->init_size;
+
+ if ((buffer_start < LOAD_PHYSICAL_ADDR) ||
+ (IS_ENABLED(CONFIG_X86_32) && buffer_end > KERNEL_IMAGE_SIZE) ||
+ (IS_ENABLED(CONFIG_X86_64) && buffer_end > MAXMEM_X86_64_4LEVEL) ||
+ (image_offset == 0 && !IS_ALIGNED(bzimage_addr,
+ hdr->kernel_alignment))) {
status = efi_relocate_kernel(&bzimage_addr,
hdr->init_size, hdr->init_size,
hdr->pref_address,