diff --git a/drivers/staging/Kconfig b/drivers/staging/Kconfig
index 348bf61..975ecdd 100644
--- a/drivers/staging/Kconfig
+++ b/drivers/staging/Kconfig
@@ -103,8 +103,6 @@
 
 source "drivers/staging/stlc45xx/Kconfig"
 
-source "drivers/staging/uc2322/Kconfig"
-
 source "drivers/staging/b3dfg/Kconfig"
 
 source "drivers/staging/phison/Kconfig"
diff --git a/drivers/staging/Makefile b/drivers/staging/Makefile
index 8d61d7b..2241ae1 100644
--- a/drivers/staging/Makefile
+++ b/drivers/staging/Makefile
@@ -34,7 +34,6 @@
 obj-$(CONFIG_DST)		+= dst/
 obj-$(CONFIG_POHMELFS)		+= pohmelfs/
 obj-$(CONFIG_STLC45XX)		+= stlc45xx/
-obj-$(CONFIG_USB_SERIAL_ATEN2011)	+= uc2322/
 obj-$(CONFIG_B3DFG)		+= b3dfg/
 obj-$(CONFIG_IDE_PHISON)	+= phison/
 obj-$(CONFIG_PLAN9AUTH)		+= p9auth/
diff --git a/drivers/staging/android/lowmemorykiller.c b/drivers/staging/android/lowmemorykiller.c
index fe72240..f934393 100644
--- a/drivers/staging/android/lowmemorykiller.c
+++ b/drivers/staging/android/lowmemorykiller.c
@@ -96,19 +96,21 @@
 
 	read_lock(&tasklist_lock);
 	for_each_process(p) {
+		struct mm_struct *mm;
 		int oom_adj;
 
 		task_lock(p);
-		if (!p->mm) {
+		mm = p->mm;
+		if (!mm) {
 			task_unlock(p);
 			continue;
 		}
-		oom_adj = p->oomkilladj;
+		oom_adj = mm->oom_adj;
 		if (oom_adj < min_adj) {
 			task_unlock(p);
 			continue;
 		}
-		tasksize = get_mm_rss(p->mm);
+		tasksize = get_mm_rss(mm);
 		task_unlock(p);
 		if (tasksize <= 0)
 			continue;
diff --git a/drivers/staging/serqt_usb2/serqt_usb2.c b/drivers/staging/serqt_usb2/serqt_usb2.c
index a9bd410..0fdf8c6 100644
--- a/drivers/staging/serqt_usb2/serqt_usb2.c
+++ b/drivers/staging/serqt_usb2/serqt_usb2.c
@@ -360,18 +360,18 @@
 	if (port_paranoia_check(port, __func__) != 0) {
 		dbg("%s - port_paranoia_check, exiting\n", __func__);
 		qt_port->ReadBulkStopped = 1;
-		return;
+		goto exit;
 	}
 
 	if (!serial) {
 		dbg("%s - bad serial pointer, exiting\n", __func__);
-		return;
+		goto exit;
 	}
 	if (qt_port->closePending == 1) {
 		/* Were closing , stop reading */
 		dbg("%s - (qt_port->closepending == 1\n", __func__);
 		qt_port->ReadBulkStopped = 1;
-		return;
+		goto exit;
 	}
 
 	/*
@@ -381,7 +381,7 @@
 	 */
 	if (qt_port->RxHolding == 1) {
 		qt_port->ReadBulkStopped = 1;
-		return;
+		goto exit;
 	}
 
 	if (urb->status) {
@@ -389,7 +389,7 @@
 
 		dbg("%s - nonzero read bulk status received: %d\n",
 		    __func__, urb->status);
-		return;
+		goto exit;
 	}
 
 	if (tty && RxCount) {
@@ -463,6 +463,8 @@
 	}
 
 	schedule_work(&port->work);
+exit:
+	tty_kref_put(tty);
 }
 
 /*
@@ -736,6 +738,11 @@
 		if (!qt_port) {
 			dbg("%s: kmalloc for quatech_port (%d) failed!.",
 			    __func__, i);
+			for(--i; i >= 0; i--) {
+				port = serial->port[i];
+				kfree(usb_get_serial_port_data(port));
+				usb_set_serial_port_data(port, NULL);
+			}
 			return -ENOMEM;
 		}
 		spin_lock_init(&qt_port->lock);
@@ -1041,7 +1048,7 @@
 	}
 }
 
-static void qt_close( struct usb_serial_port *port)
+static void qt_close(struct usb_serial_port *port)
 {
 	struct usb_serial *serial = port->serial;
 	struct quatech_port *qt_port;
@@ -1068,6 +1075,7 @@
 	/* wait up to for transmitter to empty */
 	if (serial->dev)
 		qt_block_until_empty(tty, qt_port);
+	tty_kref_put(tty);
 
 	/* Close uart channel */
 	status = qt_close_channel(serial, index);
diff --git a/drivers/staging/uc2322/Kconfig b/drivers/staging/uc2322/Kconfig
deleted file mode 100644
index 2e0c6e79..0000000
--- a/drivers/staging/uc2322/Kconfig
+++ /dev/null
@@ -1,10 +0,0 @@
-config USB_SERIAL_ATEN2011
-	tristate "ATEN 2011 USB to serial device support"
-	depends on USB_SERIAL
-	default N
-	---help---
-	  Say Y here if you want to use a ATEN 2011 dual port USB to serial
-	  adapter.
-
-	  To compile this driver as a module, choose M here: the module will be
-	  called aten2011.
diff --git a/drivers/staging/uc2322/Makefile b/drivers/staging/uc2322/Makefile
deleted file mode 100644
index 49c18d6..0000000
--- a/drivers/staging/uc2322/Makefile
+++ /dev/null
@@ -1 +0,0 @@
-obj-$(CONFIG_USB_SERIAL_ATEN2011)	+= aten2011.o
diff --git a/drivers/staging/uc2322/TODO b/drivers/staging/uc2322/TODO
deleted file mode 100644
index c189a64..0000000
--- a/drivers/staging/uc2322/TODO
+++ /dev/null
@@ -1,7 +0,0 @@
-TODO:
-	- checkpatch.pl cleanups
-	- remove dead and useless code (auditing the tty ioctls to
-	  verify that they really are correct and needed.)
-
-Please send any patches to Greg Kroah-Hartman <greg@kroah.com> and
-Russell Lang <gsview@ghostgum.com.au>.
diff --git a/drivers/staging/uc2322/aten2011.c b/drivers/staging/uc2322/aten2011.c
deleted file mode 100644
index 39d0926..0000000
--- a/drivers/staging/uc2322/aten2011.c
+++ /dev/null
@@ -1,2430 +0,0 @@
-/*
- * Aten 2011 USB serial driver for 4 port devices
- *
- * Copyright (C) 2000 Inside Out Networks
- * Copyright (C) 2001-2002, 2009 Greg Kroah-Hartman <greg@kroah.com>
- * Copyright (C) 2009 Novell Inc.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- */
-
-#include <linux/kernel.h>
-#include <linux/errno.h>
-#include <linux/init.h>
-#include <linux/slab.h>
-#include <linux/tty.h>
-#include <linux/tty_driver.h>
-#include <linux/tty_flip.h>
-#include <linux/module.h>
-#include <linux/serial.h>
-#include <linux/uaccess.h>
-#include <linux/usb.h>
-#include <linux/usb/serial.h>
-
-
-#define ZLP_REG1		0x3A	/* Zero_Flag_Reg1 58 */
-#define ZLP_REG2		0x3B	/* Zero_Flag_Reg2 59 */
-#define ZLP_REG3		0x3C	/* Zero_Flag_Reg3 60 */
-#define ZLP_REG4		0x3D	/* Zero_Flag_Reg4 61 */
-#define ZLP_REG5		0x3E	/* Zero_Flag_Reg5 62 */
-
-/* Interrupt Rotinue Defines	*/
-#define SERIAL_IIR_RLS		0x06
-#define SERIAL_IIR_RDA		0x04
-#define SERIAL_IIR_CTI		0x0c
-#define SERIAL_IIR_THR		0x02
-#define SERIAL_IIR_MS		0x00
-
-/* Emulation of the bit mask on the LINE STATUS REGISTER.  */
-#define SERIAL_LSR_DR		0x0001
-#define SERIAL_LSR_OE		0x0002
-#define SERIAL_LSR_PE		0x0004
-#define SERIAL_LSR_FE		0x0008
-#define SERIAL_LSR_BI		0x0010
-#define SERIAL_LSR_THRE		0x0020
-#define SERIAL_LSR_TEMT		0x0040
-#define SERIAL_LSR_FIFOERR	0x0080
-
-/* MSR bit defines(place holders) */
-#define ATEN_MSR_DELTA_CTS	0x10
-#define ATEN_MSR_DELTA_DSR	0x20
-#define ATEN_MSR_DELTA_RI	0x40
-#define ATEN_MSR_DELTA_CD	0x80
-
-/* Serial Port register Address */
-#define RECEIVE_BUFFER_REGISTER		((__u16)(0x00))
-#define TRANSMIT_HOLDING_REGISTER	((__u16)(0x00))
-#define INTERRUPT_ENABLE_REGISTER	((__u16)(0x01))
-#define INTERRUPT_IDENT_REGISTER	((__u16)(0x02))
-#define FIFO_CONTROL_REGISTER		((__u16)(0x02))
-#define LINE_CONTROL_REGISTER		((__u16)(0x03))
-#define MODEM_CONTROL_REGISTER		((__u16)(0x04))
-#define LINE_STATUS_REGISTER		((__u16)(0x05))
-#define MODEM_STATUS_REGISTER		((__u16)(0x06))
-#define SCRATCH_PAD_REGISTER		((__u16)(0x07))
-#define DIVISOR_LATCH_LSB		((__u16)(0x00))
-#define DIVISOR_LATCH_MSB		((__u16)(0x01))
-
-#define SP1_REGISTER			((__u16)(0x00))
-#define CONTROL1_REGISTER		((__u16)(0x01))
-#define CLK_MULTI_REGISTER		((__u16)(0x02))
-#define CLK_START_VALUE_REGISTER	((__u16)(0x03))
-#define DCR1_REGISTER			((__u16)(0x04))
-#define GPIO_REGISTER			((__u16)(0x07))
-
-#define SERIAL_LCR_DLAB			((__u16)(0x0080))
-
-/*
- * URB POOL related defines
- */
-#define NUM_URBS			16	/* URB Count */
-#define URB_TRANSFER_BUFFER_SIZE	32	/* URB Size  */
-
-#define USB_VENDOR_ID_ATENINTL		0x0557
-#define ATENINTL_DEVICE_ID_2011		0x2011
-#define ATENINTL_DEVICE_ID_7820		0x7820
-
-static struct usb_device_id id_table[] = {
-	{ USB_DEVICE(USB_VENDOR_ID_ATENINTL, ATENINTL_DEVICE_ID_2011) },
-	{ USB_DEVICE(USB_VENDOR_ID_ATENINTL, ATENINTL_DEVICE_ID_7820) },
-	{ } /* terminating entry */
-};
-MODULE_DEVICE_TABLE(usb, id_table);
-
-/* This structure holds all of the local port information */
-struct ATENINTL_port {
-	int		port_num;          /*Actual port number in the device(1,2,etc)*/
-	__u8		bulk_out_endpoint;   	/* the bulk out endpoint handle */
-	unsigned char	*bulk_out_buffer;     	/* buffer used for the bulk out endpoint */
-	struct urb	*write_urb;	     	/* write URB for this port */
-	__u8		bulk_in_endpoint;	/* the bulk in endpoint handle */
-	unsigned char	*bulk_in_buffer;	/* the buffer we use for the bulk in endpoint */
-	struct urb	*read_urb;	     	/* read URB for this port */
-	__u8		shadowLCR;		/* last LCR value received */
-	__u8		shadowMCR;		/* last MCR value received */
-	char		open;
-	char		chaseResponsePending;
-	wait_queue_head_t	wait_chase;		/* for handling sleeping while waiting for chase to finish */
-	wait_queue_head_t	wait_command;		/* for handling sleeping while waiting for command to finish */
-	struct async_icount	icount;
-	struct usb_serial_port	*port;			/* loop back to the owner of this object */
-	/*Offsets*/
-	__u8		SpRegOffset;
-	__u8		ControlRegOffset;
-	__u8		DcrRegOffset;
-	/* for processing control URBS in interrupt context */
-	struct urb 	*control_urb;
-	char		*ctrl_buf;
-	int		MsrLsr;
-
-	struct urb	*write_urb_pool[NUM_URBS];
-	/* we pass a pointer to this as the arguement sent to cypress_set_termios old_termios */
-	struct ktermios	tmp_termios;        /* stores the old termios settings */
-	spinlock_t 	lock;                   /* private lock */
-};
-
-/* This structure holds all of the individual serial device information */
-struct ATENINTL_serial {
-	__u8		interrupt_in_endpoint;		/* the interrupt endpoint handle */
-	unsigned char	*interrupt_in_buffer;		/* the buffer we use for the interrupt endpoint */
-	struct urb	*interrupt_read_urb;	/* our interrupt urb */
-	__u8		bulk_in_endpoint;	/* the bulk in endpoint handle */
-	unsigned char	*bulk_in_buffer;		/* the buffer we use for the bulk in endpoint */
-	struct urb 	*read_urb;		/* our bulk read urb */
-	__u8		bulk_out_endpoint;	/* the bulk out endpoint handle */
-	struct usb_serial	*serial;	/* loop back to the owner of this object */
-	int	ATEN2011_spectrum_2or4ports; 	/* this says the number of ports in the device */
-	/* Indicates about the no.of opened ports of an individual USB-serial adapater. */
-	unsigned int	NoOfOpenPorts;
-	/* a flag for Status endpoint polling */
-	unsigned char	status_polling_started;
-};
-
-static void ATEN2011_set_termios(struct tty_struct *tty,
-				 struct usb_serial_port *port,
-				 struct ktermios *old_termios);
-static void ATEN2011_change_port_settings(struct tty_struct *tty,
-					  struct ATENINTL_port *ATEN2011_port,
-					  struct ktermios *old_termios);
-
-/*************************************
- * Bit definitions for each register *
- *************************************/
-#define LCR_BITS_5		0x00	/* 5 bits/char */
-#define LCR_BITS_6		0x01	/* 6 bits/char */
-#define LCR_BITS_7		0x02	/* 7 bits/char */
-#define LCR_BITS_8		0x03	/* 8 bits/char */
-#define LCR_BITS_MASK		0x03	/* Mask for bits/char field */
-
-#define LCR_STOP_1		0x00	/* 1 stop bit */
-#define LCR_STOP_1_5		0x04	/* 1.5 stop bits (if 5   bits/char) */
-#define LCR_STOP_2		0x04	/* 2 stop bits   (if 6-8 bits/char) */
-#define LCR_STOP_MASK		0x04	/* Mask for stop bits field */
-
-#define LCR_PAR_NONE		0x00	/* No parity */
-#define LCR_PAR_ODD		0x08	/* Odd parity */
-#define LCR_PAR_EVEN		0x18	/* Even parity */
-#define LCR_PAR_MARK		0x28	/* Force parity bit to 1 */
-#define LCR_PAR_SPACE		0x38	/* Force parity bit to 0 */
-#define LCR_PAR_MASK		0x38	/* Mask for parity field */
-
-#define LCR_SET_BREAK		0x40	/* Set Break condition */
-#define LCR_DL_ENABLE		0x80	/* Enable access to divisor latch */
-
-#define MCR_DTR			0x01	/* Assert DTR */
-#define MCR_RTS			0x02	/* Assert RTS */
-#define MCR_OUT1		0x04	/* Loopback only: Sets state of RI */
-#define MCR_MASTER_IE		0x08	/* Enable interrupt outputs */
-#define MCR_LOOPBACK		0x10	/* Set internal (digital) loopback mode */
-#define MCR_XON_ANY		0x20	/* Enable any char to exit XOFF mode */
-
-#define ATEN2011_MSR_CTS	0x10	/* Current state of CTS */
-#define ATEN2011_MSR_DSR	0x20	/* Current state of DSR */
-#define ATEN2011_MSR_RI		0x40	/* Current state of RI */
-#define ATEN2011_MSR_CD		0x80	/* Current state of CD */
-
-
-static int debug;
-
-/*
- * Version Information
- */
-#define DRIVER_VERSION "2.0"
-#define DRIVER_DESC "ATENINTL 2011 USB Serial Adapter"
-
-/*
- * Defines used for sending commands to port
- */
-
-#define ATEN_WDR_TIMEOUT	(50)	/* default urb timeout */
-
-/* Requests */
-#define ATEN_RD_RTYPE		0xC0
-#define ATEN_WR_RTYPE		0x40
-#define ATEN_RDREQ		0x0D
-#define ATEN_WRREQ		0x0E
-#define ATEN_CTRL_TIMEOUT	500
-#define VENDOR_READ_LENGTH	(0x01)
-
-/* set to 1 for RS485 mode and 0 for RS232 mode */
-/* FIXME make this somehow dynamic and not build time specific */
-static int RS485mode;
-
-static int set_reg_sync(struct usb_serial_port *port, __u16 reg, __u16 val)
-{
-	struct usb_device *dev = port->serial->dev;
-	val = val & 0x00ff;
-
-	dbg("%s: is %x, value %x", __func__, reg, val);
-
-	return usb_control_msg(dev, usb_sndctrlpipe(dev, 0), ATEN_WRREQ,
-			       ATEN_WR_RTYPE, val, reg, NULL, 0,
-			       ATEN_WDR_TIMEOUT);
-}
-
-static int get_reg_sync(struct usb_serial_port *port, __u16 reg, __u16 *val)
-{
-	struct usb_device *dev = port->serial->dev;
-	int ret;
-
-	ret = usb_control_msg(dev, usb_rcvctrlpipe(dev, 0), ATEN_RDREQ,
-			      ATEN_RD_RTYPE, 0, reg, val, VENDOR_READ_LENGTH,
-			      ATEN_WDR_TIMEOUT);
-	dbg("%s: offset is %x, return val %x", __func__, reg, *val);
-	*val = (*val) & 0x00ff;
-	return ret;
-}
-
-static int set_uart_reg(struct usb_serial_port *port, __u16 reg, __u16 val)
-{
-	struct usb_device *dev = port->serial->dev;
-	struct ATENINTL_serial *a_serial;
-	__u16 minor;
-
-	a_serial = usb_get_serial_data(port->serial);
-	minor = port->serial->minor;
-	if (minor == SERIAL_TTY_NO_MINOR)
-		minor = 0;
-	val = val & 0x00ff;
-
-	/*
-	 * For the UART control registers,
-	 * the application number need to be Or'ed
-	 */
-	if (a_serial->ATEN2011_spectrum_2or4ports == 4)
-		val |= (((__u16)port->number - minor) + 1) << 8;
-	else {
-		if (((__u16) port->number - minor) == 0)
-			val |= (((__u16)port->number - minor) + 1) << 8;
-		else
-			val |= (((__u16)port->number - minor) + 2) << 8;
-	}
-	dbg("%s: application number is %x", __func__, val);
-
-	return usb_control_msg(dev, usb_sndctrlpipe(dev, 0), ATEN_WRREQ,
-			       ATEN_WR_RTYPE, val, reg, NULL, 0,
-			       ATEN_WDR_TIMEOUT);
-}
-
-static int get_uart_reg(struct usb_serial_port *port, __u16 reg, __u16 *val)
-{
-	struct usb_device *dev = port->serial->dev;
-	int ret = 0;
-	__u16 wval;
-	struct ATENINTL_serial *a_serial;
-	__u16 minor = port->serial->minor;
-
-	a_serial = usb_get_serial_data(port->serial);
-	if (minor == SERIAL_TTY_NO_MINOR)
-		minor = 0;
-
-	/* wval is same as application number */
-	if (a_serial->ATEN2011_spectrum_2or4ports == 4)
-		wval = (((__u16)port->number - minor) + 1) << 8;
-	else {
-		if (((__u16) port->number - minor) == 0)
-			wval = (((__u16) port->number - minor) + 1) << 8;
-		else
-			wval = (((__u16) port->number - minor) + 2) << 8;
-	}
-	dbg("%s: application number is %x", __func__, wval);
-	ret = usb_control_msg(dev, usb_rcvctrlpipe(dev, 0), ATEN_RDREQ,
-			      ATEN_RD_RTYPE, wval, reg, val, VENDOR_READ_LENGTH,
-			      ATEN_WDR_TIMEOUT);
-	*val = (*val) & 0x00ff;
-	return ret;
-}
-
-static int handle_newMsr(struct ATENINTL_port *port, __u8 newMsr)
-{
-	struct ATENINTL_port *ATEN2011_port;
-	struct async_icount *icount;
-	ATEN2011_port = port;
-	icount = &ATEN2011_port->icount;
-	if (newMsr &
-	    (ATEN_MSR_DELTA_CTS | ATEN_MSR_DELTA_DSR | ATEN_MSR_DELTA_RI |
-	     ATEN_MSR_DELTA_CD)) {
-		icount = &ATEN2011_port->icount;
-
-		/* update input line counters */
-		if (newMsr & ATEN_MSR_DELTA_CTS)
-			icount->cts++;
-		if (newMsr & ATEN_MSR_DELTA_DSR)
-			icount->dsr++;
-		if (newMsr & ATEN_MSR_DELTA_CD)
-			icount->dcd++;
-		if (newMsr & ATEN_MSR_DELTA_RI)
-			icount->rng++;
-	}
-
-	return 0;
-}
-
-static int handle_newLsr(struct ATENINTL_port *port, __u8 newLsr)
-{
-	struct async_icount *icount;
-
-	dbg("%s - %02x", __func__, newLsr);
-
-	if (newLsr & SERIAL_LSR_BI) {
-		/*
-		 * Parity and Framing errors only count if they occur exclusive
-		 * of a break being received.
-		 */
-		newLsr &= (__u8) (SERIAL_LSR_OE | SERIAL_LSR_BI);
-	}
-
-	/* update input line counters */
-	icount = &port->icount;
-	if (newLsr & SERIAL_LSR_BI)
-		icount->brk++;
-	if (newLsr & SERIAL_LSR_OE)
-		icount->overrun++;
-	if (newLsr & SERIAL_LSR_PE)
-		icount->parity++;
-	if (newLsr & SERIAL_LSR_FE)
-		icount->frame++;
-
-	return 0;
-}
-
-static void ATEN2011_control_callback(struct urb *urb)
-{
-	unsigned char *data;
-	struct ATENINTL_port *ATEN2011_port;
-	__u8 regval = 0x0;
-
-	switch (urb->status) {
-	case 0:
-		/* success */
-		break;
-	case -ECONNRESET:
-	case -ENOENT:
-	case -ESHUTDOWN:
-		/* this urb is terminated, clean up */
-		dbg("%s - urb shutting down with status: %d", __func__,
-		    urb->status);
-		return;
-	default:
-		dbg("%s - nonzero urb status received: %d", __func__,
-		    urb->status);
-		goto exit;
-	}
-
-	ATEN2011_port = (struct ATENINTL_port *)urb->context;
-
-	dbg("%s urb buffer size is %d", __func__, urb->actual_length);
-	dbg("%s ATEN2011_port->MsrLsr is %d port %d", __func__,
-		ATEN2011_port->MsrLsr, ATEN2011_port->port_num);
-	data = urb->transfer_buffer;
-	regval = (__u8) data[0];
-	dbg("%s data is %x", __func__, regval);
-	if (ATEN2011_port->MsrLsr == 0)
-		handle_newMsr(ATEN2011_port, regval);
-	else if (ATEN2011_port->MsrLsr == 1)
-		handle_newLsr(ATEN2011_port, regval);
-
-exit:
-	return;
-}
-
-static int ATEN2011_get_reg(struct ATENINTL_port *ATEN, __u16 Wval, __u16 reg,
-			    __u16 *val)
-{
-	struct usb_device *dev = ATEN->port->serial->dev;
-	struct usb_ctrlrequest *dr = NULL;
-	unsigned char *buffer = NULL;
-	int ret = 0;
-	buffer = (__u8 *) ATEN->ctrl_buf;
-
-	dr = (void *)(buffer + 2);
-	dr->bRequestType = ATEN_RD_RTYPE;
-	dr->bRequest = ATEN_RDREQ;
-	dr->wValue = cpu_to_le16(Wval);
-	dr->wIndex = cpu_to_le16(reg);
-	dr->wLength = cpu_to_le16(2);
-
-	usb_fill_control_urb(ATEN->control_urb, dev, usb_rcvctrlpipe(dev, 0),
-			     (unsigned char *)dr, buffer, 2,
-			     ATEN2011_control_callback, ATEN);
-	ATEN->control_urb->transfer_buffer_length = 2;
-	ret = usb_submit_urb(ATEN->control_urb, GFP_ATOMIC);
-	return ret;
-}
-
-static void ATEN2011_interrupt_callback(struct urb *urb)
-{
-	int result;
-	int length;
-	struct ATENINTL_port *ATEN2011_port;
-	struct ATENINTL_serial *ATEN2011_serial;
-	struct usb_serial *serial;
-	__u16 Data;
-	unsigned char *data;
-	__u8 sp[5], st;
-	int i;
-	__u16 wval;
-	int minor;
-
-	dbg("%s", " : Entering");
-
-	ATEN2011_serial = (struct ATENINTL_serial *)urb->context;
-
-	switch (urb->status) {
-	case 0:
-		/* success */
-		break;
-	case -ECONNRESET:
-	case -ENOENT:
-	case -ESHUTDOWN:
-		/* this urb is terminated, clean up */
-		dbg("%s - urb shutting down with status: %d", __func__,
-		    urb->status);
-		return;
-	default:
-		dbg("%s - nonzero urb status received: %d", __func__,
-		    urb->status);
-		goto exit;
-	}
-	length = urb->actual_length;
-	data = urb->transfer_buffer;
-
-	serial = ATEN2011_serial->serial;
-
-	/* ATENINTL get 5 bytes
-	 * Byte 1 IIR Port 1 (port.number is 0)
-	 * Byte 2 IIR Port 2 (port.number is 1)
-	 * Byte 3 IIR Port 3 (port.number is 2)
-	 * Byte 4 IIR Port 4 (port.number is 3)
-	 * Byte 5 FIFO status for both */
-
-	if (length && length > 5) {
-		dbg("%s", "Wrong data !!!");
-		return;
-	}
-
-	/* MATRIX */
-	if (ATEN2011_serial->ATEN2011_spectrum_2or4ports == 4) {
-		sp[0] = (__u8) data[0];
-		sp[1] = (__u8) data[1];
-		sp[2] = (__u8) data[2];
-		sp[3] = (__u8) data[3];
-		st = (__u8) data[4];
-	} else {
-		sp[0] = (__u8) data[0];
-		sp[1] = (__u8) data[2];
-		/* sp[2]=(__u8)data[2]; */
-		/* sp[3]=(__u8)data[3]; */
-		st = (__u8) data[4];
-
-	}
-	for (i = 0; i < serial->num_ports; i++) {
-		ATEN2011_port = usb_get_serial_port_data(serial->port[i]);
-		minor = serial->minor;
-		if (minor == SERIAL_TTY_NO_MINOR)
-			minor = 0;
-		if ((ATEN2011_serial->ATEN2011_spectrum_2or4ports == 2)
-		    && (i != 0))
-			wval =
-			    (((__u16) serial->port[i]->number -
-			      (__u16) (minor)) + 2) << 8;
-		else
-			wval =
-			    (((__u16) serial->port[i]->number -
-			      (__u16) (minor)) + 1) << 8;
-		if (ATEN2011_port->open != 0) {
-			if (sp[i] & 0x01) {
-				dbg("SP%d No Interrupt !!!", i);
-			} else {
-				switch (sp[i] & 0x0f) {
-				case SERIAL_IIR_RLS:
-					dbg("Serial Port %d: Receiver status error or address bit detected in 9-bit mode", i);
-					ATEN2011_port->MsrLsr = 1;
-					ATEN2011_get_reg(ATEN2011_port, wval,
-							 LINE_STATUS_REGISTER,
-							 &Data);
-					break;
-				case SERIAL_IIR_MS:
-					dbg("Serial Port %d: Modem status change", i);
-					ATEN2011_port->MsrLsr = 0;
-					ATEN2011_get_reg(ATEN2011_port, wval,
-							 MODEM_STATUS_REGISTER,
-							 &Data);
-					break;
-				}
-			}
-		}
-
-	}
-exit:
-	if (ATEN2011_serial->status_polling_started == 0)
-		return;
-
-	result = usb_submit_urb(urb, GFP_ATOMIC);
-	if (result) {
-		dev_err(&urb->dev->dev,
-			"%s - Error %d submitting interrupt urb\n",
-			__func__, result);
-	}
-
-	return;
-}
-
-static void ATEN2011_bulk_in_callback(struct urb *urb)
-{
-	int status;
-	unsigned char *data;
-	struct usb_serial *serial;
-	struct usb_serial_port *port;
-	struct ATENINTL_serial *ATEN2011_serial;
-	struct ATENINTL_port *ATEN2011_port;
-	struct tty_struct *tty;
-
-	if (urb->status) {
-		dbg("nonzero read bulk status received: %d", urb->status);
-		return;
-	}
-
-	ATEN2011_port = (struct ATENINTL_port *)urb->context;
-
-	port = (struct usb_serial_port *)ATEN2011_port->port;
-	serial = port->serial;
-
-	dbg("%s", "Entering...");
-
-	data = urb->transfer_buffer;
-	ATEN2011_serial = usb_get_serial_data(serial);
-
-	if (urb->actual_length) {
-		tty = tty_port_tty_get(&ATEN2011_port->port->port);
-		if (tty) {
-			tty_buffer_request_room(tty, urb->actual_length);
-			tty_insert_flip_string(tty, data, urb->actual_length);
-			tty_flip_buffer_push(tty);
-			tty_kref_put(tty);
-		}
-
-		ATEN2011_port->icount.rx += urb->actual_length;
-		dbg("ATEN2011_port->icount.rx is %d:",
-			ATEN2011_port->icount.rx);
-	}
-
-	if (!ATEN2011_port->read_urb) {
-		dbg("%s", "URB KILLED !!!");
-		return;
-	}
-
-	if (ATEN2011_port->read_urb->status != -EINPROGRESS) {
-		ATEN2011_port->read_urb->dev = serial->dev;
-
-		status = usb_submit_urb(ATEN2011_port->read_urb, GFP_ATOMIC);
-		if (status)
-			dbg("usb_submit_urb(read bulk) failed, status = %d", status);
-	}
-}
-
-static void ATEN2011_bulk_out_data_callback(struct urb *urb)
-{
-	struct ATENINTL_port *ATEN2011_port;
-	struct tty_struct *tty;
-
-	if (urb->status) {
-		dbg("nonzero write bulk status received:%d", urb->status);
-		return;
-	}
-
-	ATEN2011_port = (struct ATENINTL_port *)urb->context;
-
-	dbg("%s", "Entering .........");
-
-	tty = tty_port_tty_get(&ATEN2011_port->port->port);
-
-	if (tty && ATEN2011_port->open)
-		/* tell the tty driver that something has changed */
-		tty_wakeup(tty);
-
-	/* schedule_work(&ATEN2011_port->port->work); */
-	tty_kref_put(tty);
-
-}
-
-#ifdef ATENSerialProbe
-static int ATEN2011_serial_probe(struct usb_serial *serial,
-				 const struct usb_device_id *id)
-{
-
-	/*need to implement the mode_reg reading and updating\
-	   structures usb_serial_ device_type\
-	   (i.e num_ports, num_bulkin,bulkout etc) */
-	/* Also we can update the changes  attach */
-	return 1;
-}
-#endif
-
-static int ATEN2011_open(struct tty_struct *tty, struct usb_serial_port *port,
-			 struct file *filp)
-{
-	int response;
-	int j;
-	struct usb_serial *serial;
-	struct urb *urb;
-	__u16 Data;
-	int status;
-	struct ATENINTL_serial *ATEN2011_serial;
-	struct ATENINTL_port *ATEN2011_port;
-	struct ktermios tmp_termios;
-	int minor;
-
-	serial = port->serial;
-
-	ATEN2011_port = usb_get_serial_port_data(port);
-
-	if (ATEN2011_port == NULL)
-		return -ENODEV;
-
-	ATEN2011_serial = usb_get_serial_data(serial);
-	if (ATEN2011_serial == NULL)
-		return -ENODEV;
-
-	/* increment the number of opened ports counter here */
-	ATEN2011_serial->NoOfOpenPorts++;
-
-	usb_clear_halt(serial->dev, port->write_urb->pipe);
-	usb_clear_halt(serial->dev, port->read_urb->pipe);
-
-	/* Initialising the write urb pool */
-	for (j = 0; j < NUM_URBS; ++j) {
-		urb = usb_alloc_urb(0, GFP_ATOMIC);
-		ATEN2011_port->write_urb_pool[j] = urb;
-
-		if (urb == NULL) {
-			err("No more urbs???");
-			continue;
-		}
-
-		urb->transfer_buffer = NULL;
-		urb->transfer_buffer =
-		    kmalloc(URB_TRANSFER_BUFFER_SIZE, GFP_KERNEL);
-		if (!urb->transfer_buffer) {
-			err("%s-out of memory for urb buffers.", __func__);
-			continue;
-		}
-	}
-
-/*****************************************************************************
- * Initialize ATEN2011 -- Write Init values to corresponding Registers
- *
- * Register Index
- * 1 : IER
- * 2 : FCR
- * 3 : LCR
- * 4 : MCR
- *
- * 0x08 : SP1/2 Control Reg
- *****************************************************************************/
-
-/* NEED to check the fallowing Block */
-
-	Data = 0x0;
-	status = get_reg_sync(port, ATEN2011_port->SpRegOffset, &Data);
-	if (status < 0) {
-		dbg("Reading Spreg failed");
-		return -1;
-	}
-	Data |= 0x80;
-	status = set_reg_sync(port, ATEN2011_port->SpRegOffset, Data);
-	if (status < 0) {
-		dbg("writing Spreg failed");
-		return -1;
-	}
-
-	Data &= ~0x80;
-	status = set_reg_sync(port, ATEN2011_port->SpRegOffset, Data);
-	if (status < 0) {
-		dbg("writing Spreg failed");
-		return -1;
-	}
-
-/* End of block to be checked */
-/**************************CHECK***************************/
-
-	if (RS485mode == 0)
-		Data = 0xC0;
-	else
-		Data = 0x00;
-	status = set_uart_reg(port, SCRATCH_PAD_REGISTER, Data);
-	if (status < 0) {
-		dbg("Writing SCRATCH_PAD_REGISTER failed status-0x%x", status);
-		return -1;
-	} else
-		dbg("SCRATCH_PAD_REGISTER Writing success status%d", status);
-
-/**************************CHECK***************************/
-
-	Data = 0x0;
-	status = get_reg_sync(port, ATEN2011_port->ControlRegOffset, &Data);
-	if (status < 0) {
-		dbg("Reading Controlreg failed");
-		return -1;
-	}
-	Data |= 0x08;		/* Driver done bit */
-	Data |= 0x20;		/* rx_disable */
-	status = 0;
-	status =
-	    set_reg_sync(port, ATEN2011_port->ControlRegOffset, Data);
-	if (status < 0) {
-		dbg("writing Controlreg failed");
-		return -1;
-	}
-	/*
-	 * do register settings here
-	 * Set all regs to the device default values.
-	 * First Disable all interrupts.
-	 */
-
-	Data = 0x00;
-	status = set_uart_reg(port, INTERRUPT_ENABLE_REGISTER, Data);
-	if (status < 0) {
-		dbg("disableing interrupts failed");
-		return -1;
-	}
-	/* Set FIFO_CONTROL_REGISTER to the default value */
-	Data = 0x00;
-	status = set_uart_reg(port, FIFO_CONTROL_REGISTER, Data);
-	if (status < 0) {
-		dbg("Writing FIFO_CONTROL_REGISTER  failed");
-		return -1;
-	}
-
-	Data = 0xcf;		/* chk */
-	status = set_uart_reg(port, FIFO_CONTROL_REGISTER, Data);
-	if (status < 0) {
-		dbg("Writing FIFO_CONTROL_REGISTER  failed");
-		return -1;
-	}
-
-	Data = 0x03;		/* LCR_BITS_8 */
-	status = set_uart_reg(port, LINE_CONTROL_REGISTER, Data);
-	ATEN2011_port->shadowLCR = Data;
-
-	Data = 0x0b;		/* MCR_DTR|MCR_RTS|MCR_MASTER_IE */
-	status = set_uart_reg(port, MODEM_CONTROL_REGISTER, Data);
-	ATEN2011_port->shadowMCR = Data;
-
-#ifdef Check
-	Data = 0x00;
-	status = get_uart_reg(port, LINE_CONTROL_REGISTER, &Data);
-	ATEN2011_port->shadowLCR = Data;
-
-	Data |= SERIAL_LCR_DLAB;	/* data latch enable in LCR 0x80 */
-	status = set_uart_reg(port, LINE_CONTROL_REGISTER, Data);
-
-	Data = 0x0c;
-	status = set_uart_reg(port, DIVISOR_LATCH_LSB, Data);
-
-	Data = 0x0;
-	status = set_uart_reg(port, DIVISOR_LATCH_MSB, Data);
-
-	Data = 0x00;
-	status = get_uart_reg(port, LINE_CONTROL_REGISTER, &Data);
-
-/*      Data = ATEN2011_port->shadowLCR; */	/* data latch disable */
-	Data = Data & ~SERIAL_LCR_DLAB;
-	status = set_uart_reg(port, LINE_CONTROL_REGISTER, Data);
-	ATEN2011_port->shadowLCR = Data;
-#endif
-	/* clearing Bulkin and Bulkout Fifo */
-	Data = 0x0;
-	status = get_reg_sync(port, ATEN2011_port->SpRegOffset, &Data);
-
-	Data = Data | 0x0c;
-	status = set_reg_sync(port, ATEN2011_port->SpRegOffset, Data);
-
-	Data = Data & ~0x0c;
-	status = set_reg_sync(port, ATEN2011_port->SpRegOffset, Data);
-	/* Finally enable all interrupts */
-	Data = 0x0;
-	Data = 0x0c;
-	status = set_uart_reg(port, INTERRUPT_ENABLE_REGISTER, Data);
-
-	/* clearing rx_disable */
-	Data = 0x0;
-	status = get_reg_sync(port, ATEN2011_port->ControlRegOffset, &Data);
-	Data = Data & ~0x20;
-	status = set_reg_sync(port, ATEN2011_port->ControlRegOffset, Data);
-
-	/* rx_negate */
-	Data = 0x0;
-	status = get_reg_sync(port, ATEN2011_port->ControlRegOffset, &Data);
-	Data = Data | 0x10;
-	status = 0;
-	status = set_reg_sync(port, ATEN2011_port->ControlRegOffset, Data);
-
-	/*
-	 * Check to see if we've set up our endpoint info yet
-	 * (can't set it up in ATEN2011_startup as the structures
-	 * were not set up at that time.)
-	 */
-	if (ATEN2011_serial->NoOfOpenPorts == 1) {
-		/* start the status polling here */
-		ATEN2011_serial->status_polling_started = 1;
-		/* If not yet set, Set here */
-		ATEN2011_serial->interrupt_in_buffer =
-		    serial->port[0]->interrupt_in_buffer;
-		ATEN2011_serial->interrupt_in_endpoint =
-		    serial->port[0]->interrupt_in_endpointAddress;
-		ATEN2011_serial->interrupt_read_urb =
-		    serial->port[0]->interrupt_in_urb;
-
-		/* set up interrupt urb */
-		usb_fill_int_urb(ATEN2011_serial->interrupt_read_urb,
-				 serial->dev,
-				 usb_rcvintpipe(serial->dev,
-						ATEN2011_serial->
-						interrupt_in_endpoint),
-				 ATEN2011_serial->interrupt_in_buffer,
-				 ATEN2011_serial->interrupt_read_urb->
-				 transfer_buffer_length,
-				 ATEN2011_interrupt_callback, ATEN2011_serial,
-				 ATEN2011_serial->interrupt_read_urb->interval);
-
-		/* start interrupt read for ATEN2011               *
-		 * will continue as long as ATEN2011 is connected  */
-
-		response =
-		    usb_submit_urb(ATEN2011_serial->interrupt_read_urb,
-				   GFP_KERNEL);
-		if (response) {
-			dbg("%s - Error %d submitting interrupt urb",
-				__func__, response);
-		}
-
-	}
-
-	/*
-	 * See if we've set up our endpoint info yet
-	 * (can't set it up in ATEN2011_startup as the
-	 * structures were not set up at that time.)
-	 */
-
-	dbg("port number is %d", port->number);
-	dbg("serial number is %d", port->serial->minor);
-	dbg("Bulkin endpoint is %d", port->bulk_in_endpointAddress);
-	dbg("BulkOut endpoint is %d", port->bulk_out_endpointAddress);
-	dbg("Interrupt endpoint is %d",
-		port->interrupt_in_endpointAddress);
-	dbg("port's number in the device is %d", ATEN2011_port->port_num);
-	ATEN2011_port->bulk_in_buffer = port->bulk_in_buffer;
-	ATEN2011_port->bulk_in_endpoint = port->bulk_in_endpointAddress;
-	ATEN2011_port->read_urb = port->read_urb;
-	ATEN2011_port->bulk_out_endpoint = port->bulk_out_endpointAddress;
-
-	minor = port->serial->minor;
-	if (minor == SERIAL_TTY_NO_MINOR)
-		minor = 0;
-
-	/* set up our bulk in urb */
-	if ((ATEN2011_serial->ATEN2011_spectrum_2or4ports == 2)
-	    && (((__u16) port->number - (__u16) (minor)) != 0)) {
-		usb_fill_bulk_urb(ATEN2011_port->read_urb, serial->dev,
-				  usb_rcvbulkpipe(serial->dev,
-						  (port->
-						   bulk_in_endpointAddress +
-						   2)), port->bulk_in_buffer,
-				  ATEN2011_port->read_urb->
-				  transfer_buffer_length,
-				  ATEN2011_bulk_in_callback, ATEN2011_port);
-	} else
-		usb_fill_bulk_urb(ATEN2011_port->read_urb,
-				  serial->dev,
-				  usb_rcvbulkpipe(serial->dev,
-						  port->
-						  bulk_in_endpointAddress),
-				  port->bulk_in_buffer,
-				  ATEN2011_port->read_urb->
-				  transfer_buffer_length,
-				  ATEN2011_bulk_in_callback, ATEN2011_port);
-
-	dbg("ATEN2011_open: bulkin endpoint is %d",
-		port->bulk_in_endpointAddress);
-	response = usb_submit_urb(ATEN2011_port->read_urb, GFP_KERNEL);
-	if (response) {
-		err("%s - Error %d submitting control urb", __func__,
-		    response);
-	}
-
-	/* initialize our wait queues */
-	init_waitqueue_head(&ATEN2011_port->wait_chase);
-	init_waitqueue_head(&ATEN2011_port->wait_command);
-
-	/* initialize our icount structure */
-	memset(&(ATEN2011_port->icount), 0x00, sizeof(ATEN2011_port->icount));
-
-	/* initialize our port settings */
-	ATEN2011_port->shadowMCR = MCR_MASTER_IE;	/* Must set to enable ints! */
-	ATEN2011_port->chaseResponsePending = 0;
-	/* send a open port command */
-	ATEN2011_port->open = 1;
-	/* ATEN2011_change_port_settings(ATEN2011_port,old_termios); */
-	/* Setup termios */
-	ATEN2011_set_termios(tty, port, &tmp_termios);
-	ATEN2011_port->icount.tx = 0;
-	ATEN2011_port->icount.rx = 0;
-
-	dbg("usb_serial serial:%x       ATEN2011_port:%x\nATEN2011_serial:%x      usb_serial_port port:%x",
-	     (unsigned int)serial, (unsigned int)ATEN2011_port,
-	     (unsigned int)ATEN2011_serial, (unsigned int)port);
-
-	return 0;
-
-}
-
-static int ATEN2011_chars_in_buffer(struct tty_struct *tty)
-{
-	struct usb_serial_port *port = tty->driver_data;
-	int i;
-	int chars = 0;
-	struct ATENINTL_port *ATEN2011_port;
-
-	/* dbg("%s"," ATEN2011_chars_in_buffer:entering ..........."); */
-
-	ATEN2011_port = usb_get_serial_port_data(port);
-	if (ATEN2011_port == NULL) {
-		dbg("%s", "ATEN2011_break:leaving ...........");
-		return -1;
-	}
-
-	for (i = 0; i < NUM_URBS; ++i)
-		if (ATEN2011_port->write_urb_pool[i]->status == -EINPROGRESS)
-			chars += URB_TRANSFER_BUFFER_SIZE;
-
-	dbg("%s - returns %d", __func__, chars);
-	return chars;
-
-}
-
-static void ATEN2011_block_until_tx_empty(struct tty_struct *tty,
-					  struct ATENINTL_port *ATEN2011_port)
-{
-	int timeout = HZ / 10;
-	int wait = 30;
-	int count;
-
-	while (1) {
-		count = ATEN2011_chars_in_buffer(tty);
-
-		/* Check for Buffer status */
-		if (count <= 0)
-			return;
-
-		/* Block the thread for a while */
-		interruptible_sleep_on_timeout(&ATEN2011_port->wait_chase,
-					       timeout);
-
-		/* No activity.. count down section */
-		wait--;
-		if (wait == 0) {
-			dbg("%s - TIMEOUT", __func__);
-			return;
-		} else {
-			/* Reset timout value back to seconds */
-			wait = 30;
-		}
-	}
-}
-
-static void ATEN2011_close(struct tty_struct *tty, struct usb_serial_port *port,
-			   struct file *filp)
-{
-	struct usb_serial *serial;
-	struct ATENINTL_serial *ATEN2011_serial;
-	struct ATENINTL_port *ATEN2011_port;
-	int no_urbs;
-	__u16 Data;
-
-	dbg("%s", "ATEN2011_close:entering...");
-	serial = port->serial;
-
-	/* take the Adpater and port's private data */
-	ATEN2011_serial = usb_get_serial_data(serial);
-	ATEN2011_port = usb_get_serial_port_data(port);
-	if ((ATEN2011_serial == NULL) || (ATEN2011_port == NULL))
-		return;
-
-	if (serial->dev) {
-		/* flush and block(wait) until tx is empty */
-		ATEN2011_block_until_tx_empty(tty, ATEN2011_port);
-	}
-	/* kill the ports URB's */
-	for (no_urbs = 0; no_urbs < NUM_URBS; no_urbs++)
-		usb_kill_urb(ATEN2011_port->write_urb_pool[no_urbs]);
-	/* Freeing Write URBs */
-	for (no_urbs = 0; no_urbs < NUM_URBS; ++no_urbs) {
-		kfree(ATEN2011_port->write_urb_pool[no_urbs]->transfer_buffer);
-		usb_free_urb(ATEN2011_port->write_urb_pool[no_urbs]);
-	}
-	/* While closing port, shutdown all bulk read, write  *
-	 * and interrupt read if they exists                  */
-	if (serial->dev) {
-		if (ATEN2011_port->write_urb) {
-			dbg("%s", "Shutdown bulk write");
-			usb_kill_urb(ATEN2011_port->write_urb);
-		}
-		if (ATEN2011_port->read_urb) {
-			dbg("%s", "Shutdown bulk read");
-			usb_kill_urb(ATEN2011_port->read_urb);
-		}
-		if ((&ATEN2011_port->control_urb)) {
-			dbg("%s", "Shutdown control read");
-			/* usb_kill_urb (ATEN2011_port->control_urb); */
-
-		}
-	}
-	/* if(ATEN2011_port->ctrl_buf != NULL) */
-		/* kfree(ATEN2011_port->ctrl_buf); */
-	/* decrement the no.of open ports counter of an individual USB-serial adapter. */
-	ATEN2011_serial->NoOfOpenPorts--;
-	dbg("NoOfOpenPorts in close%d:in port%d",
-		ATEN2011_serial->NoOfOpenPorts, port->number);
-	if (ATEN2011_serial->NoOfOpenPorts == 0) {
-		/* stop the stus polling here */
-		ATEN2011_serial->status_polling_started = 0;
-		if (ATEN2011_serial->interrupt_read_urb) {
-			dbg("%s", "Shutdown interrupt_read_urb");
-			/* ATEN2011_serial->interrupt_in_buffer=NULL; */
-			/* usb_kill_urb (ATEN2011_serial->interrupt_read_urb); */
-		}
-	}
-	if (ATEN2011_port->write_urb) {
-		/* if this urb had a transfer buffer already (old tx) free it */
-		kfree(ATEN2011_port->write_urb->transfer_buffer);
-		usb_free_urb(ATEN2011_port->write_urb);
-	}
-
-	/* clear the MCR & IER */
-	Data = 0x00;
-	set_uart_reg(port, MODEM_CONTROL_REGISTER, Data);
-	Data = 0x00;
-	set_uart_reg(port, INTERRUPT_ENABLE_REGISTER, Data);
-
-	ATEN2011_port->open = 0;
-	dbg("%s", "Leaving ............");
-
-}
-
-static void ATEN2011_block_until_chase_response(struct tty_struct *tty,
-						struct ATENINTL_port
-						*ATEN2011_port)
-{
-	int timeout = 1 * HZ;
-	int wait = 10;
-	int count;
-
-	while (1) {
-		count = ATEN2011_chars_in_buffer(tty);
-
-		/* Check for Buffer status */
-		if (count <= 0) {
-			ATEN2011_port->chaseResponsePending = 0;
-			return;
-		}
-
-		/* Block the thread for a while */
-		interruptible_sleep_on_timeout(&ATEN2011_port->wait_chase,
-					       timeout);
-		/* No activity.. count down section */
-		wait--;
-		if (wait == 0) {
-			dbg("%s - TIMEOUT", __func__);
-			return;
-		} else {
-			/* Reset timout value back to seconds */
-			wait = 10;
-		}
-	}
-
-}
-
-static void ATEN2011_break(struct tty_struct *tty, int break_state)
-{
-	struct usb_serial_port *port = tty->driver_data;
-	unsigned char data;
-	struct usb_serial *serial;
-	struct ATENINTL_serial *ATEN2011_serial;
-	struct ATENINTL_port *ATEN2011_port;
-
-	dbg("%s", "Entering ...........");
-	dbg("ATEN2011_break: Start");
-
-	serial = port->serial;
-
-	ATEN2011_serial = usb_get_serial_data(serial);
-	ATEN2011_port = usb_get_serial_port_data(port);
-
-	if ((ATEN2011_serial == NULL) || (ATEN2011_port == NULL))
-		return;
-
-	/* flush and chase */
-	ATEN2011_port->chaseResponsePending = 1;
-
-	if (serial->dev) {
-		/* flush and block until tx is empty */
-		ATEN2011_block_until_chase_response(tty, ATEN2011_port);
-	}
-
-	if (break_state == -1)
-		data = ATEN2011_port->shadowLCR | LCR_SET_BREAK;
-	else
-		data = ATEN2011_port->shadowLCR & ~LCR_SET_BREAK;
-
-	ATEN2011_port->shadowLCR = data;
-	dbg("ATEN2011_break ATEN2011_port->shadowLCR is %x",
-		ATEN2011_port->shadowLCR);
-	set_uart_reg(port, LINE_CONTROL_REGISTER, ATEN2011_port->shadowLCR);
-
-	return;
-}
-
-static int ATEN2011_write_room(struct tty_struct *tty)
-{
-	struct usb_serial_port *port = tty->driver_data;
-	int i;
-	int room = 0;
-	struct ATENINTL_port *ATEN2011_port;
-
-	ATEN2011_port = usb_get_serial_port_data(port);
-	if (ATEN2011_port == NULL) {
-		dbg("%s", "ATEN2011_break:leaving ...........");
-		return -1;
-	}
-
-	for (i = 0; i < NUM_URBS; ++i)
-		if (ATEN2011_port->write_urb_pool[i]->status != -EINPROGRESS)
-			room += URB_TRANSFER_BUFFER_SIZE;
-
-	dbg("%s - returns %d", __func__, room);
-	return room;
-
-}
-
-static int ATEN2011_write(struct tty_struct *tty, struct usb_serial_port *port,
-			  const unsigned char *data, int count)
-{
-	int status;
-	int i;
-	int bytes_sent = 0;
-	int transfer_size;
-	int minor;
-
-	struct ATENINTL_port *ATEN2011_port;
-	struct usb_serial *serial;
-	struct ATENINTL_serial *ATEN2011_serial;
-	struct urb *urb;
-	const unsigned char *current_position = data;
-	unsigned char *data1;
-	dbg("%s", "entering ...........");
-
-	serial = port->serial;
-
-	ATEN2011_port = usb_get_serial_port_data(port);
-	if (ATEN2011_port == NULL) {
-		dbg("%s", "ATEN2011_port is NULL");
-		return -1;
-	}
-
-	ATEN2011_serial = usb_get_serial_data(serial);
-	if (ATEN2011_serial == NULL) {
-		dbg("%s", "ATEN2011_serial is NULL");
-		return -1;
-	}
-
-	/* try to find a free urb in the list */
-	urb = NULL;
-
-	for (i = 0; i < NUM_URBS; ++i) {
-		if (ATEN2011_port->write_urb_pool[i]->status != -EINPROGRESS) {
-			urb = ATEN2011_port->write_urb_pool[i];
-			dbg("URB:%d", i);
-			break;
-		}
-	}
-
-	if (urb == NULL) {
-		dbg("%s - no more free urbs", __func__);
-		goto exit;
-	}
-
-	if (urb->transfer_buffer == NULL) {
-		urb->transfer_buffer =
-		    kmalloc(URB_TRANSFER_BUFFER_SIZE, GFP_KERNEL);
-
-		if (urb->transfer_buffer == NULL) {
-			err("%s no more kernel memory...", __func__);
-			goto exit;
-		}
-	}
-	transfer_size = min(count, URB_TRANSFER_BUFFER_SIZE);
-
-	memcpy(urb->transfer_buffer, current_position, transfer_size);
-	/* usb_serial_debug_data (__FILE__, __func__, transfer_size, urb->transfer_buffer); */
-
-	/* fill urb with data and submit  */
-	minor = port->serial->minor;
-	if (minor == SERIAL_TTY_NO_MINOR)
-		minor = 0;
-	if ((ATEN2011_serial->ATEN2011_spectrum_2or4ports == 2)
-	    && (((__u16) port->number - (__u16) (minor)) != 0)) {
-		usb_fill_bulk_urb(urb, ATEN2011_serial->serial->dev,
-				  usb_sndbulkpipe(ATEN2011_serial->serial->dev,
-						  (port->
-						   bulk_out_endpointAddress) +
-						  2), urb->transfer_buffer,
-				  transfer_size,
-				  ATEN2011_bulk_out_data_callback,
-				  ATEN2011_port);
-	} else
-
-		usb_fill_bulk_urb(urb,
-				  ATEN2011_serial->serial->dev,
-				  usb_sndbulkpipe(ATEN2011_serial->serial->dev,
-						  port->
-						  bulk_out_endpointAddress),
-				  urb->transfer_buffer, transfer_size,
-				  ATEN2011_bulk_out_data_callback,
-				  ATEN2011_port);
-
-	data1 = urb->transfer_buffer;
-	dbg("bulkout endpoint is %d", port->bulk_out_endpointAddress);
-	/* for(i=0;i < urb->actual_length;i++) */
-		/* dbg("Data is %c ",data1[i]); */
-
-	/* send it down the pipe */
-	status = usb_submit_urb(urb, GFP_ATOMIC);
-
-	if (status) {
-		err("%s - usb_submit_urb(write bulk) failed with status = %d",
-		    __func__, status);
-		bytes_sent = status;
-		goto exit;
-	}
-	bytes_sent = transfer_size;
-	ATEN2011_port->icount.tx += transfer_size;
-	dbg("ATEN2011_port->icount.tx is %d:", ATEN2011_port->icount.tx);
-
-exit:
-	return bytes_sent;
-}
-
-static void ATEN2011_throttle(struct tty_struct *tty)
-{
-	struct usb_serial_port *port = tty->driver_data;
-	struct ATENINTL_port *ATEN2011_port;
-	int status;
-
-	dbg("- port %d", port->number);
-
-	ATEN2011_port = usb_get_serial_port_data(port);
-
-	if (ATEN2011_port == NULL)
-		return;
-
-	if (!ATEN2011_port->open) {
-		dbg("%s", "port not opened");
-		return;
-	}
-
-	dbg("%s", "Entering .......... ");
-
-	if (!tty) {
-		dbg("%s - no tty available", __func__);
-		return;
-	}
-
-	/* if we are implementing XON/XOFF, send the stop character */
-	if (I_IXOFF(tty)) {
-		unsigned char stop_char = STOP_CHAR(tty);
-		status = ATEN2011_write(tty, port, &stop_char, 1);
-		if (status <= 0)
-			return;
-	}
-
-	/* if we are implementing RTS/CTS, toggle that line */
-	if (tty->termios->c_cflag & CRTSCTS) {
-		ATEN2011_port->shadowMCR &= ~MCR_RTS;
-		status = set_uart_reg(port, MODEM_CONTROL_REGISTER,
-				      ATEN2011_port->shadowMCR);
-		if (status < 0)
-			return;
-	}
-
-	return;
-}
-
-static void ATEN2011_unthrottle(struct tty_struct *tty)
-{
-	struct usb_serial_port *port = tty->driver_data;
-	int status;
-	struct ATENINTL_port *ATEN2011_port = usb_get_serial_port_data(port);
-
-	if (ATEN2011_port == NULL)
-		return;
-
-	if (!ATEN2011_port->open) {
-		dbg("%s - port not opened", __func__);
-		return;
-	}
-
-	dbg("%s", "Entering .......... ");
-
-	if (!tty) {
-		dbg("%s - no tty available", __func__);
-		return;
-	}
-
-	/* if we are implementing XON/XOFF, send the start character */
-	if (I_IXOFF(tty)) {
-		unsigned char start_char = START_CHAR(tty);
-		status = ATEN2011_write(tty, port, &start_char, 1);
-		if (status <= 0)
-			return;
-	}
-
-	/* if we are implementing RTS/CTS, toggle that line */
-	if (tty->termios->c_cflag & CRTSCTS) {
-		ATEN2011_port->shadowMCR |= MCR_RTS;
-		status = set_uart_reg(port, MODEM_CONTROL_REGISTER,
-				      ATEN2011_port->shadowMCR);
-		if (status < 0)
-			return;
-	}
-
-	return;
-}
-
-static int ATEN2011_tiocmget(struct tty_struct *tty, struct file *file)
-{
-	struct usb_serial_port *port = tty->driver_data;
-	struct ATENINTL_port *ATEN2011_port;
-	unsigned int result;
-	__u16 msr;
-	__u16 mcr;
-	/* unsigned int mcr; */
-	int status = 0;
-	ATEN2011_port = usb_get_serial_port_data(port);
-
-	dbg("%s - port %d", __func__, port->number);
-
-	if (ATEN2011_port == NULL)
-		return -ENODEV;
-
-	status = get_uart_reg(port, MODEM_STATUS_REGISTER, &msr);
-	status = get_uart_reg(port, MODEM_CONTROL_REGISTER, &mcr);
-	/* mcr = ATEN2011_port->shadowMCR; */
-	/* COMMENT2: the Fallowing three line are commented for updating only MSR values */
-	result = ((mcr & MCR_DTR) ? TIOCM_DTR : 0)
-	    | ((mcr & MCR_RTS) ? TIOCM_RTS : 0)
-	    | ((mcr & MCR_LOOPBACK) ? TIOCM_LOOP : 0)
-	    | ((msr & ATEN2011_MSR_CTS) ? TIOCM_CTS : 0)
-	    | ((msr & ATEN2011_MSR_CD) ? TIOCM_CAR : 0)
-	    | ((msr & ATEN2011_MSR_RI) ? TIOCM_RI : 0)
-	    | ((msr & ATEN2011_MSR_DSR) ? TIOCM_DSR : 0);
-
-	dbg("%s - 0x%04X", __func__, result);
-
-	return result;
-}
-
-static int ATEN2011_tiocmset(struct tty_struct *tty, struct file *file,
-			     unsigned int set, unsigned int clear)
-{
-	struct usb_serial_port *port = tty->driver_data;
-	struct ATENINTL_port *ATEN2011_port;
-	unsigned int mcr;
-	unsigned int status;
-
-	dbg("%s - port %d", __func__, port->number);
-
-	ATEN2011_port = usb_get_serial_port_data(port);
-
-	if (ATEN2011_port == NULL)
-		return -ENODEV;
-
-	mcr = ATEN2011_port->shadowMCR;
-	if (clear & TIOCM_RTS)
-		mcr &= ~MCR_RTS;
-	if (clear & TIOCM_DTR)
-		mcr &= ~MCR_DTR;
-	if (clear & TIOCM_LOOP)
-		mcr &= ~MCR_LOOPBACK;
-
-	if (set & TIOCM_RTS)
-		mcr |= MCR_RTS;
-	if (set & TIOCM_DTR)
-		mcr |= MCR_DTR;
-	if (set & TIOCM_LOOP)
-		mcr |= MCR_LOOPBACK;
-
-	ATEN2011_port->shadowMCR = mcr;
-
-	status = set_uart_reg(port, MODEM_CONTROL_REGISTER, mcr);
-	if (status < 0) {
-		dbg("setting MODEM_CONTROL_REGISTER Failed");
-		return -1;
-	}
-
-	return 0;
-}
-
-static void ATEN2011_set_termios(struct tty_struct *tty,
-				 struct usb_serial_port *port,
-				 struct ktermios *old_termios)
-{
-	int status;
-	unsigned int cflag;
-	struct usb_serial *serial;
-	struct ATENINTL_port *ATEN2011_port;
-
-	dbg("ATEN2011_set_termios: START");
-
-	serial = port->serial;
-
-	ATEN2011_port = usb_get_serial_port_data(port);
-
-	if (ATEN2011_port == NULL)
-		return;
-
-	if (!ATEN2011_port->open) {
-		dbg("%s - port not opened", __func__);
-		return;
-	}
-
-	dbg("%s", "setting termios - ");
-
-	cflag = tty->termios->c_cflag;
-
-	dbg("%s - cflag %08x iflag %08x", __func__,
-	    tty->termios->c_cflag, RELEVANT_IFLAG(tty->termios->c_iflag));
-
-	if (old_termios) {
-		dbg("%s - old clfag %08x old iflag %08x", __func__,
-		    old_termios->c_cflag, RELEVANT_IFLAG(old_termios->c_iflag));
-	}
-
-	dbg("%s - port %d", __func__, port->number);
-
-	/* change the port settings to the new ones specified */
-
-	ATEN2011_change_port_settings(tty, ATEN2011_port, old_termios);
-
-	if (!ATEN2011_port->read_urb) {
-		dbg("%s", "URB KILLED !!!!!");
-		return;
-	}
-
-	if (ATEN2011_port->read_urb->status != -EINPROGRESS) {
-		ATEN2011_port->read_urb->dev = serial->dev;
-		status = usb_submit_urb(ATEN2011_port->read_urb, GFP_ATOMIC);
-		if (status) {
-			dbg
-			    (" usb_submit_urb(read bulk) failed, status = %d",
-			     status);
-		}
-	}
-	return;
-}
-
-static int get_lsr_info(struct tty_struct *tty,
-			struct ATENINTL_port *ATEN2011_port,
-			unsigned int __user *value)
-{
-	int count;
-	unsigned int result = 0;
-
-	count = ATEN2011_chars_in_buffer(tty);
-	if (count == 0) {
-		dbg("%s -- Empty", __func__);
-		result = TIOCSER_TEMT;
-	}
-
-	if (copy_to_user(value, &result, sizeof(int)))
-		return -EFAULT;
-	return 0;
-}
-
-static int get_number_bytes_avail(struct tty_struct *tty,
-				  struct ATENINTL_port *ATEN2011_port,
-				  unsigned int __user *value)
-{
-	unsigned int result = 0;
-
-	if (!tty)
-		return -ENOIOCTLCMD;
-
-	result = tty->read_cnt;
-
-	dbg("%s(%d) = %d", __func__, ATEN2011_port->port->number, result);
-	if (copy_to_user(value, &result, sizeof(int)))
-		return -EFAULT;
-
-	return -ENOIOCTLCMD;
-}
-
-static int set_modem_info(struct ATENINTL_port *ATEN2011_port, unsigned int cmd,
-			  unsigned int __user *value)
-{
-	unsigned int mcr;
-	unsigned int arg;
-	__u16 Data;
-	int status;
-	struct usb_serial_port *port;
-
-	if (ATEN2011_port == NULL)
-		return -1;
-
-	port = (struct usb_serial_port *)ATEN2011_port->port;
-
-	mcr = ATEN2011_port->shadowMCR;
-
-	if (copy_from_user(&arg, value, sizeof(int)))
-		return -EFAULT;
-
-	switch (cmd) {
-	case TIOCMBIS:
-		if (arg & TIOCM_RTS)
-			mcr |= MCR_RTS;
-		if (arg & TIOCM_DTR)
-			mcr |= MCR_RTS;
-		if (arg & TIOCM_LOOP)
-			mcr |= MCR_LOOPBACK;
-		break;
-
-	case TIOCMBIC:
-		if (arg & TIOCM_RTS)
-			mcr &= ~MCR_RTS;
-		if (arg & TIOCM_DTR)
-			mcr &= ~MCR_RTS;
-		if (arg & TIOCM_LOOP)
-			mcr &= ~MCR_LOOPBACK;
-		break;
-
-	case TIOCMSET:
-		/* turn off the RTS and DTR and LOOPBACK
-		 * and then only turn on what was asked to */
-		mcr &= ~(MCR_RTS | MCR_DTR | MCR_LOOPBACK);
-		mcr |= ((arg & TIOCM_RTS) ? MCR_RTS : 0);
-		mcr |= ((arg & TIOCM_DTR) ? MCR_DTR : 0);
-		mcr |= ((arg & TIOCM_LOOP) ? MCR_LOOPBACK : 0);
-		break;
-	}
-
-	ATEN2011_port->shadowMCR = mcr;
-
-	Data = ATEN2011_port->shadowMCR;
-	status = set_uart_reg(port, MODEM_CONTROL_REGISTER, Data);
-	if (status < 0) {
-		dbg("setting MODEM_CONTROL_REGISTER Failed");
-		return -1;
-	}
-
-	return 0;
-}
-
-static int get_modem_info(struct ATENINTL_port *ATEN2011_port,
-			  unsigned int __user *value)
-{
-	unsigned int result = 0;
-	__u16 msr;
-	unsigned int mcr = ATEN2011_port->shadowMCR;
-	int status;
-
-	status = get_uart_reg(ATEN2011_port->port, MODEM_STATUS_REGISTER, &msr);
-	result = ((mcr & MCR_DTR) ? TIOCM_DTR : 0)	/* 0x002 */
-	    |((mcr & MCR_RTS) ? TIOCM_RTS : 0)	/* 0x004 */
-	    |((msr & ATEN2011_MSR_CTS) ? TIOCM_CTS : 0)	/* 0x020 */
-	    |((msr & ATEN2011_MSR_CD) ? TIOCM_CAR : 0)	/* 0x040 */
-	    |((msr & ATEN2011_MSR_RI) ? TIOCM_RI : 0)	/* 0x080 */
-	    |((msr & ATEN2011_MSR_DSR) ? TIOCM_DSR : 0);	/* 0x100 */
-
-	dbg("%s -- %x", __func__, result);
-
-	if (copy_to_user(value, &result, sizeof(int)))
-		return -EFAULT;
-	return 0;
-}
-
-static int get_serial_info(struct ATENINTL_port *ATEN2011_port,
-			   struct serial_struct __user *retinfo)
-{
-	struct serial_struct tmp;
-
-	if (ATEN2011_port == NULL)
-		return -1;
-
-	if (!retinfo)
-		return -EFAULT;
-
-	memset(&tmp, 0, sizeof(tmp));
-
-	tmp.type = PORT_16550A;
-	tmp.line = ATEN2011_port->port->serial->minor;
-	if (tmp.line == SERIAL_TTY_NO_MINOR)
-		tmp.line = 0;
-	tmp.port = ATEN2011_port->port->number;
-	tmp.irq = 0;
-	tmp.flags = ASYNC_SKIP_TEST | ASYNC_AUTO_IRQ;
-	tmp.xmit_fifo_size = NUM_URBS * URB_TRANSFER_BUFFER_SIZE;
-	tmp.baud_base = 9600;
-	tmp.close_delay = 5 * HZ;
-	tmp.closing_wait = 30 * HZ;
-
-	if (copy_to_user(retinfo, &tmp, sizeof(*retinfo)))
-		return -EFAULT;
-	return 0;
-}
-
-static int ATEN2011_ioctl(struct tty_struct *tty, struct file *file,
-			  unsigned int cmd, unsigned long arg)
-{
-	struct usb_serial_port *port = tty->driver_data;
-	struct ATENINTL_port *ATEN2011_port;
-	struct async_icount cnow;
-	struct async_icount cprev;
-	struct serial_icounter_struct icount;
-	int ATENret = 0;
-	unsigned int __user *user_arg = (unsigned int __user *)arg;
-
-	ATEN2011_port = usb_get_serial_port_data(port);
-
-	if (ATEN2011_port == NULL)
-		return -1;
-
-	dbg("%s - port %d, cmd = 0x%x", __func__, port->number, cmd);
-
-	switch (cmd) {
-		/* return number of bytes available */
-
-	case TIOCINQ:
-		dbg("%s (%d) TIOCINQ", __func__, port->number);
-		return get_number_bytes_avail(tty, ATEN2011_port, user_arg);
-		break;
-
-	case TIOCOUTQ:
-		dbg("%s (%d) TIOCOUTQ", __func__, port->number);
-		return put_user(ATEN2011_chars_in_buffer(tty), user_arg);
-		break;
-
-	case TIOCSERGETLSR:
-		dbg("%s (%d) TIOCSERGETLSR", __func__, port->number);
-		return get_lsr_info(tty, ATEN2011_port, user_arg);
-		return 0;
-
-	case TIOCMBIS:
-	case TIOCMBIC:
-	case TIOCMSET:
-		dbg("%s (%d) TIOCMSET/TIOCMBIC/TIOCMSET", __func__,
-		    port->number);
-		ATENret = set_modem_info(ATEN2011_port, cmd, user_arg);
-		return ATENret;
-
-	case TIOCMGET:
-		dbg("%s (%d) TIOCMGET", __func__, port->number);
-		return get_modem_info(ATEN2011_port, user_arg);
-
-	case TIOCGSERIAL:
-		dbg("%s (%d) TIOCGSERIAL", __func__, port->number);
-		return get_serial_info(ATEN2011_port,
-				       (struct serial_struct __user *)arg);
-
-	case TIOCSSERIAL:
-		dbg("%s (%d) TIOCSSERIAL", __func__, port->number);
-		break;
-
-	case TIOCMIWAIT:
-		dbg("%s (%d) TIOCMIWAIT", __func__, port->number);
-		cprev = ATEN2011_port->icount;
-		while (1) {
-			/* see if a signal did it */
-			if (signal_pending(current))
-				return -ERESTARTSYS;
-			cnow = ATEN2011_port->icount;
-			if (cnow.rng == cprev.rng && cnow.dsr == cprev.dsr &&
-			    cnow.dcd == cprev.dcd && cnow.cts == cprev.cts)
-				return -EIO;	/* no change => error */
-			if (((arg & TIOCM_RNG) && (cnow.rng != cprev.rng)) ||
-			    ((arg & TIOCM_DSR) && (cnow.dsr != cprev.dsr)) ||
-			    ((arg & TIOCM_CD) && (cnow.dcd != cprev.dcd)) ||
-			    ((arg & TIOCM_CTS) && (cnow.cts != cprev.cts))) {
-				return 0;
-			}
-			cprev = cnow;
-		}
-		/* NOTREACHED */
-		break;
-
-	case TIOCGICOUNT:
-		cnow = ATEN2011_port->icount;
-		icount.cts = cnow.cts;
-		icount.dsr = cnow.dsr;
-		icount.rng = cnow.rng;
-		icount.dcd = cnow.dcd;
-		icount.rx = cnow.rx;
-		icount.tx = cnow.tx;
-		icount.frame = cnow.frame;
-		icount.overrun = cnow.overrun;
-		icount.parity = cnow.parity;
-		icount.brk = cnow.brk;
-		icount.buf_overrun = cnow.buf_overrun;
-
-		dbg("%s (%d) TIOCGICOUNT RX=%d, TX=%d", __func__,
-		    port->number, icount.rx, icount.tx);
-		if (copy_to_user((void __user *)arg, &icount, sizeof(icount)))
-			return -EFAULT;
-		return 0;
-
-	default:
-		break;
-	}
-
-	return -ENOIOCTLCMD;
-}
-
-static int ATEN2011_calc_baud_rate_divisor(int baudRate, int *divisor,
-					   __u16 *clk_sel_val)
-{
-	dbg("%s - %d", __func__, baudRate);
-
-	if (baudRate <= 115200) {
-		*divisor = 115200 / baudRate;
-		*clk_sel_val = 0x0;
-	}
-	if ((baudRate > 115200) && (baudRate <= 230400)) {
-		*divisor = 230400 / baudRate;
-		*clk_sel_val = 0x10;
-	} else if ((baudRate > 230400) && (baudRate <= 403200)) {
-		*divisor = 403200 / baudRate;
-		*clk_sel_val = 0x20;
-	} else if ((baudRate > 403200) && (baudRate <= 460800)) {
-		*divisor = 460800 / baudRate;
-		*clk_sel_val = 0x30;
-	} else if ((baudRate > 460800) && (baudRate <= 806400)) {
-		*divisor = 806400 / baudRate;
-		*clk_sel_val = 0x40;
-	} else if ((baudRate > 806400) && (baudRate <= 921600)) {
-		*divisor = 921600 / baudRate;
-		*clk_sel_val = 0x50;
-	} else if ((baudRate > 921600) && (baudRate <= 1572864)) {
-		*divisor = 1572864 / baudRate;
-		*clk_sel_val = 0x60;
-	} else if ((baudRate > 1572864) && (baudRate <= 3145728)) {
-		*divisor = 3145728 / baudRate;
-		*clk_sel_val = 0x70;
-	}
-	return 0;
-}
-
-static int ATEN2011_send_cmd_write_baud_rate(struct ATENINTL_port
-					     *ATEN2011_port, int baudRate)
-{
-	int divisor = 0;
-	int status;
-	__u16 Data;
-	unsigned char number;
-	__u16 clk_sel_val;
-	struct usb_serial_port *port;
-	int minor;
-
-	if (ATEN2011_port == NULL)
-		return -1;
-
-	port = (struct usb_serial_port *)ATEN2011_port->port;
-
-	dbg("%s", "Entering .......... ");
-
-	minor = ATEN2011_port->port->serial->minor;
-	if (minor == SERIAL_TTY_NO_MINOR)
-		minor = 0;
-	number = ATEN2011_port->port->number - minor;
-
-	dbg("%s - port = %d, baud = %d", __func__,
-	    ATEN2011_port->port->number, baudRate);
-	/* reset clk_uart_sel in spregOffset */
-	if (baudRate > 115200) {
-#ifdef HW_flow_control
-		/*
-		 * NOTE: need to see the pther register to modify
-		 * setting h/w flow control bit to 1;
-		 */
-		/* Data = ATEN2011_port->shadowMCR; */
-		Data = 0x2b;
-		ATEN2011_port->shadowMCR = Data;
-		status = set_uart_reg(port, MODEM_CONTROL_REGISTER, Data);
-		if (status < 0) {
-			dbg("Writing spreg failed in set_serial_baud");
-			return -1;
-		}
-#endif
-
-	} else {
-#ifdef HW_flow_control
-		/* setting h/w flow control bit to 0; */
-		/* Data = ATEN2011_port->shadowMCR; */
-		Data = 0xb;
-		ATEN2011_port->shadowMCR = Data;
-		status = set_uart_reg(port, MODEM_CONTROL_REGISTER, Data);
-		if (status < 0) {
-			dbg("Writing spreg failed in set_serial_baud");
-			return -1;
-		}
-#endif
-
-	}
-
-	if (1)			/* baudRate <= 115200) */ {
-		clk_sel_val = 0x0;
-		Data = 0x0;
-		status =
-		    ATEN2011_calc_baud_rate_divisor(baudRate, &divisor,
-						    &clk_sel_val);
-		status = get_reg_sync(port, ATEN2011_port->SpRegOffset, &Data);
-		if (status < 0) {
-			dbg("reading spreg failed in set_serial_baud");
-			return -1;
-		}
-		Data = (Data & 0x8f) | clk_sel_val;
-		status = set_reg_sync(port, ATEN2011_port->SpRegOffset, Data);
-		if (status < 0) {
-			dbg("Writing spreg failed in set_serial_baud");
-			return -1;
-		}
-		/* Calculate the Divisor */
-
-		if (status) {
-			err("%s - bad baud rate", __func__);
-			dbg("%s", "bad baud rate");
-			return status;
-		}
-		/* Enable access to divisor latch */
-		Data = ATEN2011_port->shadowLCR | SERIAL_LCR_DLAB;
-		ATEN2011_port->shadowLCR = Data;
-		set_uart_reg(port, LINE_CONTROL_REGISTER, Data);
-
-		/* Write the divisor */
-		Data = (unsigned char)(divisor & 0xff);
-		dbg("set_serial_baud Value to write DLL is %x", Data);
-		set_uart_reg(port, DIVISOR_LATCH_LSB, Data);
-
-		Data = (unsigned char)((divisor & 0xff00) >> 8);
-		dbg("set_serial_baud Value to write DLM is %x", Data);
-		set_uart_reg(port, DIVISOR_LATCH_MSB, Data);
-
-		/* Disable access to divisor latch */
-		Data = ATEN2011_port->shadowLCR & ~SERIAL_LCR_DLAB;
-		ATEN2011_port->shadowLCR = Data;
-		set_uart_reg(port, LINE_CONTROL_REGISTER, Data);
-
-	}
-
-	return status;
-}
-
-static void ATEN2011_change_port_settings(struct tty_struct *tty,
-					  struct ATENINTL_port *ATEN2011_port,
-					  struct ktermios *old_termios)
-{
-	int baud;
-	unsigned cflag;
-	unsigned iflag;
-	__u8 lData;
-	__u8 lParity;
-	__u8 lStop;
-	int status;
-	__u16 Data;
-	struct usb_serial_port *port;
-	struct usb_serial *serial;
-
-	if (ATEN2011_port == NULL)
-		return;
-
-	port = (struct usb_serial_port *)ATEN2011_port->port;
-
-	serial = port->serial;
-
-	dbg("%s - port %d", __func__, ATEN2011_port->port->number);
-
-	if (!ATEN2011_port->open) {
-		dbg("%s - port not opened", __func__);
-		return;
-	}
-
-	if ((!tty) || (!tty->termios)) {
-		dbg("%s - no tty structures", __func__);
-		return;
-	}
-
-	dbg("%s", "Entering .......... ");
-
-	lData = LCR_BITS_8;
-	lStop = LCR_STOP_1;
-	lParity = LCR_PAR_NONE;
-
-	cflag = tty->termios->c_cflag;
-	iflag = tty->termios->c_iflag;
-
-	/* Change the number of bits */
-
-	/* COMMENT1: the below Line"if(cflag & CSIZE)" is added for the errors we get for serial loop data test i.e serial_loopback.pl -v */
-	/* if(cflag & CSIZE) */
-	{
-		switch (cflag & CSIZE) {
-		case CS5:
-			lData = LCR_BITS_5;
-			break;
-
-		case CS6:
-			lData = LCR_BITS_6;
-			break;
-
-		case CS7:
-			lData = LCR_BITS_7;
-			break;
-		default:
-		case CS8:
-			lData = LCR_BITS_8;
-			break;
-		}
-	}
-	/* Change the Parity bit */
-	if (cflag & PARENB) {
-		if (cflag & PARODD) {
-			lParity = LCR_PAR_ODD;
-			dbg("%s - parity = odd", __func__);
-		} else {
-			lParity = LCR_PAR_EVEN;
-			dbg("%s - parity = even", __func__);
-		}
-
-	} else {
-		dbg("%s - parity = none", __func__);
-	}
-
-	if (cflag & CMSPAR)
-		lParity = lParity | 0x20;
-
-	/* Change the Stop bit */
-	if (cflag & CSTOPB) {
-		lStop = LCR_STOP_2;
-		dbg("%s - stop bits = 2", __func__);
-	} else {
-		lStop = LCR_STOP_1;
-		dbg("%s - stop bits = 1", __func__);
-	}
-
-	/* Update the LCR with the correct value */
-	ATEN2011_port->shadowLCR &=
-	    ~(LCR_BITS_MASK | LCR_STOP_MASK | LCR_PAR_MASK);
-	ATEN2011_port->shadowLCR |= (lData | lParity | lStop);
-
-	dbg
-	    ("ATEN2011_change_port_settings ATEN2011_port->shadowLCR is %x",
-	     ATEN2011_port->shadowLCR);
-	/* Disable Interrupts */
-	Data = 0x00;
-	set_uart_reg(port, INTERRUPT_ENABLE_REGISTER, Data);
-
-	Data = 0x00;
-	set_uart_reg(port, FIFO_CONTROL_REGISTER, Data);
-
-	Data = 0xcf;
-	set_uart_reg(port, FIFO_CONTROL_REGISTER, Data);
-
-	/* Send the updated LCR value to the ATEN2011 */
-	Data = ATEN2011_port->shadowLCR;
-
-	set_uart_reg(port, LINE_CONTROL_REGISTER, Data);
-
-	Data = 0x00b;
-	ATEN2011_port->shadowMCR = Data;
-	set_uart_reg(port, MODEM_CONTROL_REGISTER, Data);
-	Data = 0x00b;
-	set_uart_reg(port, MODEM_CONTROL_REGISTER, Data);
-
-	/* set up the MCR register and send it to the ATEN2011 */
-
-	ATEN2011_port->shadowMCR = MCR_MASTER_IE;
-	if (cflag & CBAUD)
-		ATEN2011_port->shadowMCR |= (MCR_DTR | MCR_RTS);
-
-	if (cflag & CRTSCTS)
-		ATEN2011_port->shadowMCR |= (MCR_XON_ANY);
-	else
-		ATEN2011_port->shadowMCR &= ~(MCR_XON_ANY);
-
-	Data = ATEN2011_port->shadowMCR;
-	set_uart_reg(port, MODEM_CONTROL_REGISTER, Data);
-
-	/* Determine divisor based on baud rate */
-	baud = tty_get_baud_rate(tty);
-
-	if (!baud) {
-		/* pick a default, any default... */
-		dbg("%s", "Picked default baud...");
-		baud = 9600;
-	}
-
-	dbg("%s - baud rate = %d", __func__, baud);
-	status = ATEN2011_send_cmd_write_baud_rate(ATEN2011_port, baud);
-
-	/* Enable Interrupts */
-	Data = 0x0c;
-	set_uart_reg(port, INTERRUPT_ENABLE_REGISTER, Data);
-
-	if (ATEN2011_port->read_urb->status != -EINPROGRESS) {
-		ATEN2011_port->read_urb->dev = serial->dev;
-
-		status = usb_submit_urb(ATEN2011_port->read_urb, GFP_ATOMIC);
-
-		if (status) {
-			dbg
-			    (" usb_submit_urb(read bulk) failed, status = %d",
-			     status);
-		}
-	}
-	dbg
-	    ("ATEN2011_change_port_settings ATEN2011_port->shadowLCR is End %x",
-	     ATEN2011_port->shadowLCR);
-
-	return;
-}
-
-static int ATEN2011_calc_num_ports(struct usb_serial *serial)
-{
-
-	__u16 Data = 0x00;
-	int ret = 0;
-	int ATEN2011_2or4ports;
-	ret = usb_control_msg(serial->dev, usb_rcvctrlpipe(serial->dev, 0),
-			      ATEN_RDREQ, ATEN_RD_RTYPE, 0, GPIO_REGISTER,
-			      &Data, VENDOR_READ_LENGTH, ATEN_WDR_TIMEOUT);
-
-/* ghostgum: here is where the problem appears to bet */
-/* Which of the following are needed? */
-/* Greg used the serial->type->num_ports=2 */
-/* But the code in the ATEN2011_open relies on serial->num_ports=2 */
-	if ((Data & 0x01) == 0) {
-		ATEN2011_2or4ports = 2;
-		serial->type->num_ports = 2;
-		serial->num_ports = 2;
-	}
-	/* else if(serial->interface->cur_altsetting->desc.bNumEndpoints == 9) */
-	else {
-		ATEN2011_2or4ports = 4;
-		serial->type->num_ports = 4;
-		serial->num_ports = 4;
-
-	}
-
-	return ATEN2011_2or4ports;
-}
-
-static int ATEN2011_startup(struct usb_serial *serial)
-{
-	struct ATENINTL_serial *ATEN2011_serial;
-	struct ATENINTL_port *ATEN2011_port;
-	struct usb_device *dev;
-	int i, status;
-	int minor;
-
-	__u16 Data;
-	dbg("%s", " ATEN2011_startup :entering..........");
-
-	if (!serial) {
-		dbg("%s", "Invalid Handler");
-		return -1;
-	}
-
-	dev = serial->dev;
-
-	dbg("%s", "Entering...");
-
-	/* create our private serial structure */
-	ATEN2011_serial = kzalloc(sizeof(struct ATENINTL_serial), GFP_KERNEL);
-	if (ATEN2011_serial == NULL) {
-		err("%s - Out of memory", __func__);
-		return -ENOMEM;
-	}
-
-	/* resetting the private structure field values to zero */
-	memset(ATEN2011_serial, 0, sizeof(struct ATENINTL_serial));
-
-	ATEN2011_serial->serial = serial;
-	/* initilize status polling flag to 0 */
-	ATEN2011_serial->status_polling_started = 0;
-
-	usb_set_serial_data(serial, ATEN2011_serial);
-	ATEN2011_serial->ATEN2011_spectrum_2or4ports =
-	    ATEN2011_calc_num_ports(serial);
-	/* we set up the pointers to the endpoints in the ATEN2011_open *
-	 * function, as the structures aren't created yet.             */
-
-	/* set up port private structures */
-	for (i = 0; i < serial->num_ports; ++i) {
-		ATEN2011_port =
-		    kmalloc(sizeof(struct ATENINTL_port), GFP_KERNEL);
-		if (ATEN2011_port == NULL) {
-			err("%s - Out of memory", __func__);
-			usb_set_serial_data(serial, NULL);
-			kfree(ATEN2011_serial);
-			return -ENOMEM;
-		}
-		memset(ATEN2011_port, 0, sizeof(struct ATENINTL_port));
-
-		/*
-		 * Initialize all port interrupt end point to port 0
-		 * int endpoint. Our device has only one interrupt end point
-		 * comman to all port
-		 */
-		/* serial->port[i]->interrupt_in_endpointAddress = serial->port[0]->interrupt_in_endpointAddress; */
-
-		ATEN2011_port->port = serial->port[i];
-		usb_set_serial_port_data(serial->port[i], ATEN2011_port);
-
-		minor = serial->port[i]->serial->minor;
-		if (minor == SERIAL_TTY_NO_MINOR)
-			minor = 0;
-		ATEN2011_port->port_num =
-		    ((serial->port[i]->number - minor) + 1);
-
-		if (ATEN2011_port->port_num == 1) {
-			ATEN2011_port->SpRegOffset = 0x0;
-			ATEN2011_port->ControlRegOffset = 0x1;
-			ATEN2011_port->DcrRegOffset = 0x4;
-		} else if ((ATEN2011_port->port_num == 2)
-			   && (ATEN2011_serial->ATEN2011_spectrum_2or4ports ==
-			       4)) {
-			ATEN2011_port->SpRegOffset = 0x8;
-			ATEN2011_port->ControlRegOffset = 0x9;
-			ATEN2011_port->DcrRegOffset = 0x16;
-		} else if ((ATEN2011_port->port_num == 2)
-			   && (ATEN2011_serial->ATEN2011_spectrum_2or4ports ==
-			       2)) {
-			ATEN2011_port->SpRegOffset = 0xa;
-			ATEN2011_port->ControlRegOffset = 0xb;
-			ATEN2011_port->DcrRegOffset = 0x19;
-		} else if ((ATEN2011_port->port_num == 3)
-			   && (ATEN2011_serial->ATEN2011_spectrum_2or4ports ==
-			       4)) {
-			ATEN2011_port->SpRegOffset = 0xa;
-			ATEN2011_port->ControlRegOffset = 0xb;
-			ATEN2011_port->DcrRegOffset = 0x19;
-		} else if ((ATEN2011_port->port_num == 4)
-			   && (ATEN2011_serial->ATEN2011_spectrum_2or4ports ==
-			       4)) {
-			ATEN2011_port->SpRegOffset = 0xc;
-			ATEN2011_port->ControlRegOffset = 0xd;
-			ATEN2011_port->DcrRegOffset = 0x1c;
-		}
-
-		usb_set_serial_port_data(serial->port[i], ATEN2011_port);
-
-		/* enable rx_disable bit in control register */
-
-		status = get_reg_sync(serial->port[i],
-				      ATEN2011_port->ControlRegOffset, &Data);
-		if (status < 0) {
-			dbg("Reading ControlReg failed status-0x%x",
-				status);
-			break;
-		} else
-			dbg
-			    ("ControlReg Reading success val is %x, status%d",
-			     Data, status);
-		Data |= 0x08;	/* setting driver done bit */
-		Data |= 0x04;	/* sp1_bit to have cts change reflect in modem status reg */
-
-		/* Data |= 0x20; */	/* rx_disable bit */
-		status = set_reg_sync(serial->port[i],
-				      ATEN2011_port->ControlRegOffset, Data);
-		if (status < 0) {
-			dbg
-			    ("Writing ControlReg failed(rx_disable) status-0x%x",
-			     status);
-			break;
-		} else
-			dbg
-			    ("ControlReg Writing success(rx_disable) status%d",
-			     status);
-
-		/*
-		 * Write default values in DCR (i.e 0x01 in DCR0, 0x05 in DCR2
-		 * and 0x24 in DCR3
-		 */
-		Data = 0x01;
-		status = set_reg_sync(serial->port[i],
-				      (__u16)(ATEN2011_port->DcrRegOffset + 0),
-				      Data);
-		if (status < 0) {
-			dbg("Writing DCR0 failed status-0x%x", status);
-			break;
-		} else
-			dbg("DCR0 Writing success status%d", status);
-
-		Data = 0x05;
-		status = set_reg_sync(serial->port[i],
-				      (__u16)(ATEN2011_port->DcrRegOffset + 1),
-				      Data);
-		if (status < 0) {
-			dbg("Writing DCR1 failed status-0x%x", status);
-			break;
-		} else
-			dbg("DCR1 Writing success status%d", status);
-
-		Data = 0x24;
-		status = set_reg_sync(serial->port[i],
-				      (__u16)(ATEN2011_port->DcrRegOffset + 2),
-				      Data);
-		if (status < 0) {
-			dbg("Writing DCR2 failed status-0x%x", status);
-			break;
-		} else
-			dbg("DCR2 Writing success status%d", status);
-
-		/* write values in clkstart0x0 and clkmulti 0x20 */
-		Data = 0x0;
-		status = set_reg_sync(serial->port[i], CLK_START_VALUE_REGISTER,
-				      Data);
-		if (status < 0) {
-			dbg
-			    ("Writing CLK_START_VALUE_REGISTER failed status-0x%x",
-			     status);
-			break;
-		} else
-			dbg
-			    ("CLK_START_VALUE_REGISTER Writing success status%d",
-			     status);
-
-		Data = 0x20;
-		status = set_reg_sync(serial->port[i], CLK_MULTI_REGISTER,
-				      Data);
-		if (status < 0) {
-			dbg
-			    ("Writing CLK_MULTI_REGISTER failed status-0x%x",
-			     status);
-			break;
-		} else
-			dbg("CLK_MULTI_REGISTER Writing success status%d",
-				status);
-
-		/* Zero Length flag register */
-		if ((ATEN2011_port->port_num != 1)
-		    && (ATEN2011_serial->ATEN2011_spectrum_2or4ports == 2)) {
-
-			Data = 0xff;
-			status = set_reg_sync(serial->port[i],
-					      (__u16)(ZLP_REG1 + ((__u16)ATEN2011_port->port_num)),
-					      Data);
-			dbg("ZLIP offset%x",
-				(__u16) (ZLP_REG1 +
-					 ((__u16) ATEN2011_port->port_num)));
-			if (status < 0) {
-				dbg
-				    ("Writing ZLP_REG%d failed status-0x%x",
-				     i + 2, status);
-				break;
-			} else
-				dbg("ZLP_REG%d Writing success status%d",
-					i + 2, status);
-		} else {
-			Data = 0xff;
-			status = set_reg_sync(serial->port[i],
-					      (__u16)(ZLP_REG1 + ((__u16)ATEN2011_port->port_num) - 0x1),
-					      Data);
-			dbg("ZLIP offset%x",
-				(__u16) (ZLP_REG1 +
-					 ((__u16) ATEN2011_port->port_num) -
-					 0x1));
-			if (status < 0) {
-				dbg
-				    ("Writing ZLP_REG%d failed status-0x%x",
-				     i + 1, status);
-				break;
-			} else
-				dbg("ZLP_REG%d Writing success status%d",
-					i + 1, status);
-
-		}
-		ATEN2011_port->control_urb = usb_alloc_urb(0, GFP_ATOMIC);
-		ATEN2011_port->ctrl_buf = kmalloc(16, GFP_KERNEL);
-
-	}
-
-	/* Zero Length flag enable */
-	Data = 0x0f;
-	status = set_reg_sync(serial->port[0], ZLP_REG5, Data);
-	if (status < 0) {
-		dbg("Writing ZLP_REG5 failed status-0x%x", status);
-		return -1;
-	} else
-		dbg("ZLP_REG5 Writing success status%d", status);
-
-	/* setting configuration feature to one */
-	usb_control_msg(serial->dev, usb_sndctrlpipe(serial->dev, 0),
-			(__u8) 0x03, 0x00, 0x01, 0x00, NULL, 0x00, 5 * HZ);
-	return 0;
-}
-
-static void ATEN2011_release(struct usb_serial *serial)
-{
-	int i;
-	struct ATENINTL_port *ATEN2011_port;
-
-	/* check for the ports to be closed,close the ports and disconnect */
-
-	/* free private structure allocated for serial port  *
-	 * stop reads and writes on all ports                */
-
-	for (i = 0; i < serial->num_ports; ++i) {
-		ATEN2011_port = usb_get_serial_port_data(serial->port[i]);
-		kfree(ATEN2011_port->ctrl_buf);
-		usb_kill_urb(ATEN2011_port->control_urb);
-		kfree(ATEN2011_port);
-		usb_set_serial_port_data(serial->port[i], NULL);
-	}
-
-	/* free private structure allocated for serial device */
-
-	kfree(usb_get_serial_data(serial));
-	usb_set_serial_data(serial, NULL);
-}
-
-static struct usb_serial_driver aten_serial_driver = {
-	.driver = {
-		.owner =	THIS_MODULE,
-		.name =		"aten2011",
-		},
-	.description =		DRIVER_DESC,
-	.id_table =		id_table,
-	.open =			ATEN2011_open,
-	.close =		ATEN2011_close,
-	.write =		ATEN2011_write,
-	.write_room =		ATEN2011_write_room,
-	.chars_in_buffer =	ATEN2011_chars_in_buffer,
-	.throttle =		ATEN2011_throttle,
-	.unthrottle =		ATEN2011_unthrottle,
-	.calc_num_ports =	ATEN2011_calc_num_ports,
-
-	.ioctl =		ATEN2011_ioctl,
-	.set_termios =		ATEN2011_set_termios,
-	.break_ctl =		ATEN2011_break,
-	.tiocmget =		ATEN2011_tiocmget,
-	.tiocmset =		ATEN2011_tiocmset,
-	.attach =		ATEN2011_startup,
-	.release =		ATEN2011_release,
-	.read_bulk_callback =	ATEN2011_bulk_in_callback,
-	.read_int_callback =	ATEN2011_interrupt_callback,
-};
-
-static struct usb_driver aten_driver = {
-	.name =		"aten2011",
-	.probe =	usb_serial_probe,
-	.disconnect =	usb_serial_disconnect,
-	.id_table =	id_table,
-};
-
-static int __init aten_init(void)
-{
-	int retval;
-
-	/* Register with the usb serial */
-	retval = usb_serial_register(&aten_serial_driver);
-	if (retval)
-		return retval;
-
-	printk(KERN_INFO KBUILD_MODNAME ":"
-	       DRIVER_DESC " " DRIVER_VERSION "\n");
-
-	/* Register with the usb */
-	retval = usb_register(&aten_driver);
-	if (retval)
-		usb_serial_deregister(&aten_serial_driver);
-
-	return retval;
-}
-
-static void __exit aten_exit(void)
-{
-	usb_deregister(&aten_driver);
-	usb_serial_deregister(&aten_serial_driver);
-}
-
-module_init(aten_init);
-module_exit(aten_exit);
-
-/* Module information */
-MODULE_DESCRIPTION(DRIVER_DESC);
-MODULE_LICENSE("GPL");
-
-MODULE_PARM_DESC(debug, "Debug enabled or not");
diff --git a/drivers/staging/udlfb/udlfb.c b/drivers/staging/udlfb/udlfb.c
index 0ab9d15..f5416af 100644
--- a/drivers/staging/udlfb/udlfb.c
+++ b/drivers/staging/udlfb/udlfb.c
@@ -21,6 +21,7 @@
 #include <linux/mm.h>
 #include <linux/fb.h>
 #include <linux/mutex.h>
+#include <linux/vmalloc.h>
 
 #include "udlfb.h"