serial: 8250: Split base port operations from universal driver
Refactor base port operations into new file; 8250_port.c.
Legacy irq handling, RSA port support, port storage for universal
driver, driver definition, module parameters and linkage remain in
8250_core.c
The source file split and resulting modules is diagrammed below:
8250_core.c ====> 8250_core.c __
\ \
\ +-- 8250.ko (alias 8250_core)
\ 8250_pnp.c __/ (universal driver)
\
=> 8250_port.c __
\
+-- 8250_base.ko
8250_dma.c __/ (port operations)
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
diff --git a/drivers/tty/serial/8250/8250.h b/drivers/tty/serial/8250/8250.h
index c43f74c..dd23310 100644
--- a/drivers/tty/serial/8250/8250.h
+++ b/drivers/tty/serial/8250/8250.h
@@ -211,3 +211,14 @@
}
return 1;
}
+
+static inline int serial_index(struct uart_port *port)
+{
+ return port->minor - 64;
+}
+
+#if 0
+#define DEBUG_INTR(fmt...) printk(fmt)
+#else
+#define DEBUG_INTR(fmt...) do { } while (0)
+#endif
diff --git a/drivers/tty/serial/8250/8250_core.c b/drivers/tty/serial/8250/8250_core.c
index 37fff12..cfbb9d7 100644
--- a/drivers/tty/serial/8250/8250_core.c
+++ b/drivers/tty/serial/8250/8250_core.c
@@ -1,25 +1,23 @@
/*
- * Driver for 8250/16550-type serial ports
+ * Universal/legacy driver for 8250/16550-type serial ports
*
* Based on drivers/char/serial.c, by Linus Torvalds, Theodore Ts'o.
*
* Copyright (C) 2001 Russell King.
*
+ * Supports: ISA-compatible 8250/16550 ports
+ * PNP 8250/16550 ports
+ * early_serial_setup() ports
+ * userspace-configurable "phantom" ports
+ * "serial8250" platform devices
+ * serial8250_register_8250_port() ports
+ *
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
- *
- * A note about mapbase / membase
- *
- * mapbase is the physical address of the IO port.
- * membase is an 'ioremapped' cookie.
*/
-#if defined(CONFIG_SERIAL_8250_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
-#define SUPPORT_SYSRQ
-#endif
-
#include <linux/module.h>
#include <linux/moduleparam.h>
#include <linux/ioport.h>
@@ -58,33 +56,10 @@
static struct uart_driver serial8250_reg;
-static int serial_index(struct uart_port *port)
-{
- return port->minor - 64;
-}
-
static unsigned int skip_txen_test; /* force skip of txen test at init time */
-/*
- * Debugging.
- */
-#if 0
-#define DEBUG_AUTOCONF(fmt...) printk(fmt)
-#else
-#define DEBUG_AUTOCONF(fmt...) do { } while (0)
-#endif
-
-#if 0
-#define DEBUG_INTR(fmt...) printk(fmt)
-#else
-#define DEBUG_INTR(fmt...) do { } while (0)
-#endif
-
#define PASS_LIMIT 512
-#define BOTH_EMPTY (UART_LSR_TEMT | UART_LSR_THRE)
-
-
#include <asm/serial.h>
/*
* SERIAL_PORT_DFNS tells us about built-in ports that have no
@@ -120,1563 +95,6 @@
static DEFINE_MUTEX(hash_mutex); /* Used to walk the hash */
/*
- * Here we define the default xmit fifo size used for each type of UART.
- */
-static const struct serial8250_config uart_config[] = {
- [PORT_UNKNOWN] = {
- .name = "unknown",
- .fifo_size = 1,
- .tx_loadsz = 1,
- },
- [PORT_8250] = {
- .name = "8250",
- .fifo_size = 1,
- .tx_loadsz = 1,
- },
- [PORT_16450] = {
- .name = "16450",
- .fifo_size = 1,
- .tx_loadsz = 1,
- },
- [PORT_16550] = {
- .name = "16550",
- .fifo_size = 1,
- .tx_loadsz = 1,
- },
- [PORT_16550A] = {
- .name = "16550A",
- .fifo_size = 16,
- .tx_loadsz = 16,
- .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10,
- .rxtrig_bytes = {1, 4, 8, 14},
- .flags = UART_CAP_FIFO,
- },
- [PORT_CIRRUS] = {
- .name = "Cirrus",
- .fifo_size = 1,
- .tx_loadsz = 1,
- },
- [PORT_16650] = {
- .name = "ST16650",
- .fifo_size = 1,
- .tx_loadsz = 1,
- .flags = UART_CAP_FIFO | UART_CAP_EFR | UART_CAP_SLEEP,
- },
- [PORT_16650V2] = {
- .name = "ST16650V2",
- .fifo_size = 32,
- .tx_loadsz = 16,
- .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_01 |
- UART_FCR_T_TRIG_00,
- .rxtrig_bytes = {8, 16, 24, 28},
- .flags = UART_CAP_FIFO | UART_CAP_EFR | UART_CAP_SLEEP,
- },
- [PORT_16750] = {
- .name = "TI16750",
- .fifo_size = 64,
- .tx_loadsz = 64,
- .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10 |
- UART_FCR7_64BYTE,
- .rxtrig_bytes = {1, 16, 32, 56},
- .flags = UART_CAP_FIFO | UART_CAP_SLEEP | UART_CAP_AFE,
- },
- [PORT_STARTECH] = {
- .name = "Startech",
- .fifo_size = 1,
- .tx_loadsz = 1,
- },
- [PORT_16C950] = {
- .name = "16C950/954",
- .fifo_size = 128,
- .tx_loadsz = 128,
- .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10,
- /* UART_CAP_EFR breaks billionon CF bluetooth card. */
- .flags = UART_CAP_FIFO | UART_CAP_SLEEP,
- },
- [PORT_16654] = {
- .name = "ST16654",
- .fifo_size = 64,
- .tx_loadsz = 32,
- .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_01 |
- UART_FCR_T_TRIG_10,
- .rxtrig_bytes = {8, 16, 56, 60},
- .flags = UART_CAP_FIFO | UART_CAP_EFR | UART_CAP_SLEEP,
- },
- [PORT_16850] = {
- .name = "XR16850",
- .fifo_size = 128,
- .tx_loadsz = 128,
- .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10,
- .flags = UART_CAP_FIFO | UART_CAP_EFR | UART_CAP_SLEEP,
- },
- [PORT_RSA] = {
- .name = "RSA",
- .fifo_size = 2048,
- .tx_loadsz = 2048,
- .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_11,
- .flags = UART_CAP_FIFO,
- },
- [PORT_NS16550A] = {
- .name = "NS16550A",
- .fifo_size = 16,
- .tx_loadsz = 16,
- .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10,
- .flags = UART_CAP_FIFO | UART_NATSEMI,
- },
- [PORT_XSCALE] = {
- .name = "XScale",
- .fifo_size = 32,
- .tx_loadsz = 32,
- .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10,
- .flags = UART_CAP_FIFO | UART_CAP_UUE | UART_CAP_RTOIE,
- },
- [PORT_OCTEON] = {
- .name = "OCTEON",
- .fifo_size = 64,
- .tx_loadsz = 64,
- .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10,
- .flags = UART_CAP_FIFO,
- },
- [PORT_AR7] = {
- .name = "AR7",
- .fifo_size = 16,
- .tx_loadsz = 16,
- .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_00,
- .flags = UART_CAP_FIFO | UART_CAP_AFE,
- },
- [PORT_U6_16550A] = {
- .name = "U6_16550A",
- .fifo_size = 64,
- .tx_loadsz = 64,
- .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10,
- .flags = UART_CAP_FIFO | UART_CAP_AFE,
- },
- [PORT_TEGRA] = {
- .name = "Tegra",
- .fifo_size = 32,
- .tx_loadsz = 8,
- .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_01 |
- UART_FCR_T_TRIG_01,
- .rxtrig_bytes = {1, 4, 8, 14},
- .flags = UART_CAP_FIFO | UART_CAP_RTOIE,
- },
- [PORT_XR17D15X] = {
- .name = "XR17D15X",
- .fifo_size = 64,
- .tx_loadsz = 64,
- .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10,
- .flags = UART_CAP_FIFO | UART_CAP_AFE | UART_CAP_EFR |
- UART_CAP_SLEEP,
- },
- [PORT_XR17V35X] = {
- .name = "XR17V35X",
- .fifo_size = 256,
- .tx_loadsz = 256,
- .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_11 |
- UART_FCR_T_TRIG_11,
- .flags = UART_CAP_FIFO | UART_CAP_AFE | UART_CAP_EFR |
- UART_CAP_SLEEP,
- },
- [PORT_LPC3220] = {
- .name = "LPC3220",
- .fifo_size = 64,
- .tx_loadsz = 32,
- .fcr = UART_FCR_DMA_SELECT | UART_FCR_ENABLE_FIFO |
- UART_FCR_R_TRIG_00 | UART_FCR_T_TRIG_00,
- .flags = UART_CAP_FIFO,
- },
- [PORT_BRCM_TRUMANAGE] = {
- .name = "TruManage",
- .fifo_size = 1,
- .tx_loadsz = 1024,
- .flags = UART_CAP_HFIFO,
- },
- [PORT_8250_CIR] = {
- .name = "CIR port"
- },
- [PORT_ALTR_16550_F32] = {
- .name = "Altera 16550 FIFO32",
- .fifo_size = 32,
- .tx_loadsz = 32,
- .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10,
- .flags = UART_CAP_FIFO | UART_CAP_AFE,
- },
- [PORT_ALTR_16550_F64] = {
- .name = "Altera 16550 FIFO64",
- .fifo_size = 64,
- .tx_loadsz = 64,
- .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10,
- .flags = UART_CAP_FIFO | UART_CAP_AFE,
- },
- [PORT_ALTR_16550_F128] = {
- .name = "Altera 16550 FIFO128",
- .fifo_size = 128,
- .tx_loadsz = 128,
- .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10,
- .flags = UART_CAP_FIFO | UART_CAP_AFE,
- },
-/* tx_loadsz is set to 63-bytes instead of 64-bytes to implement
-workaround of errata A-008006 which states that tx_loadsz should be
-configured less than Maximum supported fifo bytes */
- [PORT_16550A_FSL64] = {
- .name = "16550A_FSL64",
- .fifo_size = 64,
- .tx_loadsz = 63,
- .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10 |
- UART_FCR7_64BYTE,
- .flags = UART_CAP_FIFO,
- },
-};
-
-/* Uart divisor latch read */
-static int default_serial_dl_read(struct uart_8250_port *up)
-{
- return serial_in(up, UART_DLL) | serial_in(up, UART_DLM) << 8;
-}
-
-/* Uart divisor latch write */
-static void default_serial_dl_write(struct uart_8250_port *up, int value)
-{
- serial_out(up, UART_DLL, value & 0xff);
- serial_out(up, UART_DLM, value >> 8 & 0xff);
-}
-
-#if defined(CONFIG_MIPS_ALCHEMY) || defined(CONFIG_SERIAL_8250_RT288X)
-
-/* Au1x00/RT288x UART hardware has a weird register layout */
-static const s8 au_io_in_map[8] = {
- 0, /* UART_RX */
- 2, /* UART_IER */
- 3, /* UART_IIR */
- 5, /* UART_LCR */
- 6, /* UART_MCR */
- 7, /* UART_LSR */
- 8, /* UART_MSR */
- -1, /* UART_SCR (unmapped) */
-};
-
-static const s8 au_io_out_map[8] = {
- 1, /* UART_TX */
- 2, /* UART_IER */
- 4, /* UART_FCR */
- 5, /* UART_LCR */
- 6, /* UART_MCR */
- -1, /* UART_LSR (unmapped) */
- -1, /* UART_MSR (unmapped) */
- -1, /* UART_SCR (unmapped) */
-};
-
-static unsigned int au_serial_in(struct uart_port *p, int offset)
-{
- if (offset >= ARRAY_SIZE(au_io_in_map))
- return UINT_MAX;
- offset = au_io_in_map[offset];
- if (offset < 0)
- return UINT_MAX;
- return __raw_readl(p->membase + (offset << p->regshift));
-}
-
-static void au_serial_out(struct uart_port *p, int offset, int value)
-{
- if (offset >= ARRAY_SIZE(au_io_out_map))
- return;
- offset = au_io_out_map[offset];
- if (offset < 0)
- return;
- __raw_writel(value, p->membase + (offset << p->regshift));
-}
-
-/* Au1x00 haven't got a standard divisor latch */
-static int au_serial_dl_read(struct uart_8250_port *up)
-{
- return __raw_readl(up->port.membase + 0x28);
-}
-
-static void au_serial_dl_write(struct uart_8250_port *up, int value)
-{
- __raw_writel(value, up->port.membase + 0x28);
-}
-
-#endif
-
-static unsigned int hub6_serial_in(struct uart_port *p, int offset)
-{
- offset = offset << p->regshift;
- outb(p->hub6 - 1 + offset, p->iobase);
- return inb(p->iobase + 1);
-}
-
-static void hub6_serial_out(struct uart_port *p, int offset, int value)
-{
- offset = offset << p->regshift;
- outb(p->hub6 - 1 + offset, p->iobase);
- outb(value, p->iobase + 1);
-}
-
-static unsigned int mem_serial_in(struct uart_port *p, int offset)
-{
- offset = offset << p->regshift;
- return readb(p->membase + offset);
-}
-
-static void mem_serial_out(struct uart_port *p, int offset, int value)
-{
- offset = offset << p->regshift;
- writeb(value, p->membase + offset);
-}
-
-static void mem32_serial_out(struct uart_port *p, int offset, int value)
-{
- offset = offset << p->regshift;
- writel(value, p->membase + offset);
-}
-
-static unsigned int mem32_serial_in(struct uart_port *p, int offset)
-{
- offset = offset << p->regshift;
- return readl(p->membase + offset);
-}
-
-static void mem32be_serial_out(struct uart_port *p, int offset, int value)
-{
- offset = offset << p->regshift;
- iowrite32be(value, p->membase + offset);
-}
-
-static unsigned int mem32be_serial_in(struct uart_port *p, int offset)
-{
- offset = offset << p->regshift;
- return ioread32be(p->membase + offset);
-}
-
-static unsigned int io_serial_in(struct uart_port *p, int offset)
-{
- offset = offset << p->regshift;
- return inb(p->iobase + offset);
-}
-
-static void io_serial_out(struct uart_port *p, int offset, int value)
-{
- offset = offset << p->regshift;
- outb(value, p->iobase + offset);
-}
-
-static int serial8250_default_handle_irq(struct uart_port *port);
-static int exar_handle_irq(struct uart_port *port);
-
-static void set_io_from_upio(struct uart_port *p)
-{
- struct uart_8250_port *up = up_to_u8250p(p);
-
- up->dl_read = default_serial_dl_read;
- up->dl_write = default_serial_dl_write;
-
- switch (p->iotype) {
- case UPIO_HUB6:
- p->serial_in = hub6_serial_in;
- p->serial_out = hub6_serial_out;
- break;
-
- case UPIO_MEM:
- p->serial_in = mem_serial_in;
- p->serial_out = mem_serial_out;
- break;
-
- case UPIO_MEM32:
- p->serial_in = mem32_serial_in;
- p->serial_out = mem32_serial_out;
- break;
-
- case UPIO_MEM32BE:
- p->serial_in = mem32be_serial_in;
- p->serial_out = mem32be_serial_out;
- break;
-
-#if defined(CONFIG_MIPS_ALCHEMY) || defined(CONFIG_SERIAL_8250_RT288X)
- case UPIO_AU:
- p->serial_in = au_serial_in;
- p->serial_out = au_serial_out;
- up->dl_read = au_serial_dl_read;
- up->dl_write = au_serial_dl_write;
- break;
-#endif
-
- default:
- p->serial_in = io_serial_in;
- p->serial_out = io_serial_out;
- break;
- }
- /* Remember loaded iotype */
- up->cur_iotype = p->iotype;
- p->handle_irq = serial8250_default_handle_irq;
-}
-
-static void
-serial_port_out_sync(struct uart_port *p, int offset, int value)
-{
- switch (p->iotype) {
- case UPIO_MEM:
- case UPIO_MEM32:
- case UPIO_MEM32BE:
- case UPIO_AU:
- p->serial_out(p, offset, value);
- p->serial_in(p, UART_LCR); /* safe, no side-effects */
- break;
- default:
- p->serial_out(p, offset, value);
- }
-}
-
-/*
- * For the 16C950
- */
-static void serial_icr_write(struct uart_8250_port *up, int offset, int value)
-{
- serial_out(up, UART_SCR, offset);
- serial_out(up, UART_ICR, value);
-}
-
-static unsigned int serial_icr_read(struct uart_8250_port *up, int offset)
-{
- unsigned int value;
-
- serial_icr_write(up, UART_ACR, up->acr | UART_ACR_ICRRD);
- serial_out(up, UART_SCR, offset);
- value = serial_in(up, UART_ICR);
- serial_icr_write(up, UART_ACR, up->acr);
-
- return value;
-}
-
-/*
- * FIFO support.
- */
-static void serial8250_clear_fifos(struct uart_8250_port *p)
-{
- if (p->capabilities & UART_CAP_FIFO) {
- serial_out(p, UART_FCR, UART_FCR_ENABLE_FIFO);
- serial_out(p, UART_FCR, UART_FCR_ENABLE_FIFO |
- UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT);
- serial_out(p, UART_FCR, 0);
- }
-}
-
-void serial8250_clear_and_reinit_fifos(struct uart_8250_port *p)
-{
- serial8250_clear_fifos(p);
- serial_out(p, UART_FCR, p->fcr);
-}
-EXPORT_SYMBOL_GPL(serial8250_clear_and_reinit_fifos);
-
-void serial8250_rpm_get(struct uart_8250_port *p)
-{
- if (!(p->capabilities & UART_CAP_RPM))
- return;
- pm_runtime_get_sync(p->port.dev);
-}
-EXPORT_SYMBOL_GPL(serial8250_rpm_get);
-
-void serial8250_rpm_put(struct uart_8250_port *p)
-{
- if (!(p->capabilities & UART_CAP_RPM))
- return;
- pm_runtime_mark_last_busy(p->port.dev);
- pm_runtime_put_autosuspend(p->port.dev);
-}
-EXPORT_SYMBOL_GPL(serial8250_rpm_put);
-
-/*
- * These two wrappers ensure that enable_runtime_pm_tx() can be called more than
- * once and disable_runtime_pm_tx() will still disable RPM because the fifo is
- * empty and the HW can idle again.
- */
-static void serial8250_rpm_get_tx(struct uart_8250_port *p)
-{
- unsigned char rpm_active;
-
- if (!(p->capabilities & UART_CAP_RPM))
- return;
-
- rpm_active = xchg(&p->rpm_tx_active, 1);
- if (rpm_active)
- return;
- pm_runtime_get_sync(p->port.dev);
-}
-
-static void serial8250_rpm_put_tx(struct uart_8250_port *p)
-{
- unsigned char rpm_active;
-
- if (!(p->capabilities & UART_CAP_RPM))
- return;
-
- rpm_active = xchg(&p->rpm_tx_active, 0);
- if (!rpm_active)
- return;
- pm_runtime_mark_last_busy(p->port.dev);
- pm_runtime_put_autosuspend(p->port.dev);
-}
-
-/*
- * IER sleep support. UARTs which have EFRs need the "extended
- * capability" bit enabled. Note that on XR16C850s, we need to
- * reset LCR to write to IER.
- */
-static void serial8250_set_sleep(struct uart_8250_port *p, int sleep)
-{
- unsigned char lcr = 0, efr = 0;
- /*
- * Exar UARTs have a SLEEP register that enables or disables
- * each UART to enter sleep mode separately. On the XR17V35x the
- * register is accessible to each UART at the UART_EXAR_SLEEP
- * offset but the UART channel may only write to the corresponding
- * bit.
- */
- serial8250_rpm_get(p);
- if ((p->port.type == PORT_XR17V35X) ||
- (p->port.type == PORT_XR17D15X)) {
- serial_out(p, UART_EXAR_SLEEP, sleep ? 0xff : 0);
- goto out;
- }
-
- if (p->capabilities & UART_CAP_SLEEP) {
- if (p->capabilities & UART_CAP_EFR) {
- lcr = serial_in(p, UART_LCR);
- efr = serial_in(p, UART_EFR);
- serial_out(p, UART_LCR, UART_LCR_CONF_MODE_B);
- serial_out(p, UART_EFR, UART_EFR_ECB);
- serial_out(p, UART_LCR, 0);
- }
- serial_out(p, UART_IER, sleep ? UART_IERX_SLEEP : 0);
- if (p->capabilities & UART_CAP_EFR) {
- serial_out(p, UART_LCR, UART_LCR_CONF_MODE_B);
- serial_out(p, UART_EFR, efr);
- serial_out(p, UART_LCR, lcr);
- }
- }
-out:
- serial8250_rpm_put(p);
-}
-
-#ifdef CONFIG_SERIAL_8250_RSA
-/*
- * Attempts to turn on the RSA FIFO. Returns zero on failure.
- * We set the port uart clock rate if we succeed.
- */
-static int __enable_rsa(struct uart_8250_port *up)
-{
- unsigned char mode;
- int result;
-
- mode = serial_in(up, UART_RSA_MSR);
- result = mode & UART_RSA_MSR_FIFO;
-
- if (!result) {
- serial_out(up, UART_RSA_MSR, mode | UART_RSA_MSR_FIFO);
- mode = serial_in(up, UART_RSA_MSR);
- result = mode & UART_RSA_MSR_FIFO;
- }
-
- if (result)
- up->port.uartclk = SERIAL_RSA_BAUD_BASE * 16;
-
- return result;
-}
-
-static void enable_rsa(struct uart_8250_port *up)
-{
- if (up->port.type == PORT_RSA) {
- if (up->port.uartclk != SERIAL_RSA_BAUD_BASE * 16) {
- spin_lock_irq(&up->port.lock);
- __enable_rsa(up);
- spin_unlock_irq(&up->port.lock);
- }
- if (up->port.uartclk == SERIAL_RSA_BAUD_BASE * 16)
- serial_out(up, UART_RSA_FRR, 0);
- }
-}
-
-/*
- * Attempts to turn off the RSA FIFO. Returns zero on failure.
- * It is unknown why interrupts were disabled in here. However,
- * the caller is expected to preserve this behaviour by grabbing
- * the spinlock before calling this function.
- */
-static void disable_rsa(struct uart_8250_port *up)
-{
- unsigned char mode;
- int result;
-
- if (up->port.type == PORT_RSA &&
- up->port.uartclk == SERIAL_RSA_BAUD_BASE * 16) {
- spin_lock_irq(&up->port.lock);
-
- mode = serial_in(up, UART_RSA_MSR);
- result = !(mode & UART_RSA_MSR_FIFO);
-
- if (!result) {
- serial_out(up, UART_RSA_MSR, mode & ~UART_RSA_MSR_FIFO);
- mode = serial_in(up, UART_RSA_MSR);
- result = !(mode & UART_RSA_MSR_FIFO);
- }
-
- if (result)
- up->port.uartclk = SERIAL_RSA_BAUD_BASE_LO * 16;
- spin_unlock_irq(&up->port.lock);
- }
-}
-#endif /* CONFIG_SERIAL_8250_RSA */
-
-/*
- * This is a quickie test to see how big the FIFO is.
- * It doesn't work at all the time, more's the pity.
- */
-static int size_fifo(struct uart_8250_port *up)
-{
- unsigned char old_fcr, old_mcr, old_lcr;
- unsigned short old_dl;
- int count;
-
- old_lcr = serial_in(up, UART_LCR);
- serial_out(up, UART_LCR, 0);
- old_fcr = serial_in(up, UART_FCR);
- old_mcr = serial_in(up, UART_MCR);
- serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO |
- UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT);
- serial_out(up, UART_MCR, UART_MCR_LOOP);
- serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A);
- old_dl = serial_dl_read(up);
- serial_dl_write(up, 0x0001);
- serial_out(up, UART_LCR, 0x03);
- for (count = 0; count < 256; count++)
- serial_out(up, UART_TX, count);
- mdelay(20);/* FIXME - schedule_timeout */
- for (count = 0; (serial_in(up, UART_LSR) & UART_LSR_DR) &&
- (count < 256); count++)
- serial_in(up, UART_RX);
- serial_out(up, UART_FCR, old_fcr);
- serial_out(up, UART_MCR, old_mcr);
- serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A);
- serial_dl_write(up, old_dl);
- serial_out(up, UART_LCR, old_lcr);
-
- return count;
-}
-
-/*
- * Read UART ID using the divisor method - set DLL and DLM to zero
- * and the revision will be in DLL and device type in DLM. We
- * preserve the device state across this.
- */
-static unsigned int autoconfig_read_divisor_id(struct uart_8250_port *p)
-{
- unsigned char old_dll, old_dlm, old_lcr;
- unsigned int id;
-
- old_lcr = serial_in(p, UART_LCR);
- serial_out(p, UART_LCR, UART_LCR_CONF_MODE_A);
-
- old_dll = serial_in(p, UART_DLL);
- old_dlm = serial_in(p, UART_DLM);
-
- serial_out(p, UART_DLL, 0);
- serial_out(p, UART_DLM, 0);
-
- id = serial_in(p, UART_DLL) | serial_in(p, UART_DLM) << 8;
-
- serial_out(p, UART_DLL, old_dll);
- serial_out(p, UART_DLM, old_dlm);
- serial_out(p, UART_LCR, old_lcr);
-
- return id;
-}
-
-/*
- * This is a helper routine to autodetect StarTech/Exar/Oxsemi UART's.
- * When this function is called we know it is at least a StarTech
- * 16650 V2, but it might be one of several StarTech UARTs, or one of
- * its clones. (We treat the broken original StarTech 16650 V1 as a
- * 16550, and why not? Startech doesn't seem to even acknowledge its
- * existence.)
- *
- * What evil have men's minds wrought...
- */
-static void autoconfig_has_efr(struct uart_8250_port *up)
-{
- unsigned int id1, id2, id3, rev;
-
- /*
- * Everything with an EFR has SLEEP
- */
- up->capabilities |= UART_CAP_EFR | UART_CAP_SLEEP;
-
- /*
- * First we check to see if it's an Oxford Semiconductor UART.
- *
- * If we have to do this here because some non-National
- * Semiconductor clone chips lock up if you try writing to the
- * LSR register (which serial_icr_read does)
- */
-
- /*
- * Check for Oxford Semiconductor 16C950.
- *
- * EFR [4] must be set else this test fails.
- *
- * This shouldn't be necessary, but Mike Hudson (Exoray@isys.ca)
- * claims that it's needed for 952 dual UART's (which are not
- * recommended for new designs).
- */
- up->acr = 0;
- serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
- serial_out(up, UART_EFR, UART_EFR_ECB);
- serial_out(up, UART_LCR, 0x00);
- id1 = serial_icr_read(up, UART_ID1);
- id2 = serial_icr_read(up, UART_ID2);
- id3 = serial_icr_read(up, UART_ID3);
- rev = serial_icr_read(up, UART_REV);
-
- DEBUG_AUTOCONF("950id=%02x:%02x:%02x:%02x ", id1, id2, id3, rev);
-
- if (id1 == 0x16 && id2 == 0xC9 &&
- (id3 == 0x50 || id3 == 0x52 || id3 == 0x54)) {
- up->port.type = PORT_16C950;
-
- /*
- * Enable work around for the Oxford Semiconductor 952 rev B
- * chip which causes it to seriously miscalculate baud rates
- * when DLL is 0.
- */
- if (id3 == 0x52 && rev == 0x01)
- up->bugs |= UART_BUG_QUOT;
- return;
- }
-
- /*
- * We check for a XR16C850 by setting DLL and DLM to 0, and then
- * reading back DLL and DLM. The chip type depends on the DLM
- * value read back:
- * 0x10 - XR16C850 and the DLL contains the chip revision.
- * 0x12 - XR16C2850.
- * 0x14 - XR16C854.
- */
- id1 = autoconfig_read_divisor_id(up);
- DEBUG_AUTOCONF("850id=%04x ", id1);
-
- id2 = id1 >> 8;
- if (id2 == 0x10 || id2 == 0x12 || id2 == 0x14) {
- up->port.type = PORT_16850;
- return;
- }
-
- /*
- * It wasn't an XR16C850.
- *
- * We distinguish between the '654 and the '650 by counting
- * how many bytes are in the FIFO. I'm using this for now,
- * since that's the technique that was sent to me in the
- * serial driver update, but I'm not convinced this works.
- * I've had problems doing this in the past. -TYT
- */
- if (size_fifo(up) == 64)
- up->port.type = PORT_16654;
- else
- up->port.type = PORT_16650V2;
-}
-
-/*
- * We detected a chip without a FIFO. Only two fall into
- * this category - the original 8250 and the 16450. The
- * 16450 has a scratch register (accessible with LCR=0)
- */
-static void autoconfig_8250(struct uart_8250_port *up)
-{
- unsigned char scratch, status1, status2;
-
- up->port.type = PORT_8250;
-
- scratch = serial_in(up, UART_SCR);
- serial_out(up, UART_SCR, 0xa5);
- status1 = serial_in(up, UART_SCR);
- serial_out(up, UART_SCR, 0x5a);
- status2 = serial_in(up, UART_SCR);
- serial_out(up, UART_SCR, scratch);
-
- if (status1 == 0xa5 && status2 == 0x5a)
- up->port.type = PORT_16450;
-}
-
-static int broken_efr(struct uart_8250_port *up)
-{
- /*
- * Exar ST16C2550 "A2" devices incorrectly detect as
- * having an EFR, and report an ID of 0x0201. See
- * http://linux.derkeiler.com/Mailing-Lists/Kernel/2004-11/4812.html
- */
- if (autoconfig_read_divisor_id(up) == 0x0201 && size_fifo(up) == 16)
- return 1;
-
- return 0;
-}
-
-/*
- * We know that the chip has FIFOs. Does it have an EFR? The
- * EFR is located in the same register position as the IIR and
- * we know the top two bits of the IIR are currently set. The
- * EFR should contain zero. Try to read the EFR.
- */
-static void autoconfig_16550a(struct uart_8250_port *up)
-{
- unsigned char status1, status2;
- unsigned int iersave;
-
- up->port.type = PORT_16550A;
- up->capabilities |= UART_CAP_FIFO;
-
- /*
- * XR17V35x UARTs have an extra divisor register, DLD
- * that gets enabled with when DLAB is set which will
- * cause the device to incorrectly match and assign
- * port type to PORT_16650. The EFR for this UART is
- * found at offset 0x09. Instead check the Deice ID (DVID)
- * register for a 2, 4 or 8 port UART.
- */
- if (up->port.flags & UPF_EXAR_EFR) {
- status1 = serial_in(up, UART_EXAR_DVID);
- if (status1 == 0x82 || status1 == 0x84 || status1 == 0x88) {
- DEBUG_AUTOCONF("Exar XR17V35x ");
- up->port.type = PORT_XR17V35X;
- up->capabilities |= UART_CAP_AFE | UART_CAP_EFR |
- UART_CAP_SLEEP;
-
- return;
- }
-
- }
-
- /*
- * Check for presence of the EFR when DLAB is set.
- * Only ST16C650V1 UARTs pass this test.
- */
- serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A);
- if (serial_in(up, UART_EFR) == 0) {
- serial_out(up, UART_EFR, 0xA8);
- if (serial_in(up, UART_EFR) != 0) {
- DEBUG_AUTOCONF("EFRv1 ");
- up->port.type = PORT_16650;
- up->capabilities |= UART_CAP_EFR | UART_CAP_SLEEP;
- } else {
- serial_out(up, UART_LCR, 0);
- serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO |
- UART_FCR7_64BYTE);
- status1 = serial_in(up, UART_IIR) >> 5;
- serial_out(up, UART_FCR, 0);
- serial_out(up, UART_LCR, 0);
-
- if (status1 == 7)
- up->port.type = PORT_16550A_FSL64;
- else
- DEBUG_AUTOCONF("Motorola 8xxx DUART ");
- }
- serial_out(up, UART_EFR, 0);
- return;
- }
-
- /*
- * Maybe it requires 0xbf to be written to the LCR.
- * (other ST16C650V2 UARTs, TI16C752A, etc)
- */
- serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
- if (serial_in(up, UART_EFR) == 0 && !broken_efr(up)) {
- DEBUG_AUTOCONF("EFRv2 ");
- autoconfig_has_efr(up);
- return;
- }
-
- /*
- * Check for a National Semiconductor SuperIO chip.
- * Attempt to switch to bank 2, read the value of the LOOP bit
- * from EXCR1. Switch back to bank 0, change it in MCR. Then
- * switch back to bank 2, read it from EXCR1 again and check
- * it's changed. If so, set baud_base in EXCR2 to 921600. -- dwmw2
- */
- serial_out(up, UART_LCR, 0);
- status1 = serial_in(up, UART_MCR);
- serial_out(up, UART_LCR, 0xE0);
- status2 = serial_in(up, 0x02); /* EXCR1 */
-
- if (!((status2 ^ status1) & UART_MCR_LOOP)) {
- serial_out(up, UART_LCR, 0);
- serial_out(up, UART_MCR, status1 ^ UART_MCR_LOOP);
- serial_out(up, UART_LCR, 0xE0);
- status2 = serial_in(up, 0x02); /* EXCR1 */
- serial_out(up, UART_LCR, 0);
- serial_out(up, UART_MCR, status1);
-
- if ((status2 ^ status1) & UART_MCR_LOOP) {
- unsigned short quot;
-
- serial_out(up, UART_LCR, 0xE0);
-
- quot = serial_dl_read(up);
- quot <<= 3;
-
- if (ns16550a_goto_highspeed(up))
- serial_dl_write(up, quot);
-
- serial_out(up, UART_LCR, 0);
-
- up->port.uartclk = 921600*16;
- up->port.type = PORT_NS16550A;
- up->capabilities |= UART_NATSEMI;
- return;
- }
- }
-
- /*
- * No EFR. Try to detect a TI16750, which only sets bit 5 of
- * the IIR when 64 byte FIFO mode is enabled when DLAB is set.
- * Try setting it with and without DLAB set. Cheap clones
- * set bit 5 without DLAB set.
- */
- serial_out(up, UART_LCR, 0);
- serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO | UART_FCR7_64BYTE);
- status1 = serial_in(up, UART_IIR) >> 5;
- serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO);
- serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A);
- serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO | UART_FCR7_64BYTE);
- status2 = serial_in(up, UART_IIR) >> 5;
- serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO);
- serial_out(up, UART_LCR, 0);
-
- DEBUG_AUTOCONF("iir1=%d iir2=%d ", status1, status2);
-
- if (status1 == 6 && status2 == 7) {
- up->port.type = PORT_16750;
- up->capabilities |= UART_CAP_AFE | UART_CAP_SLEEP;
- return;
- }
-
- /*
- * Try writing and reading the UART_IER_UUE bit (b6).
- * If it works, this is probably one of the Xscale platform's
- * internal UARTs.
- * We're going to explicitly set the UUE bit to 0 before
- * trying to write and read a 1 just to make sure it's not
- * already a 1 and maybe locked there before we even start start.
- */
- iersave = serial_in(up, UART_IER);
- serial_out(up, UART_IER, iersave & ~UART_IER_UUE);
- if (!(serial_in(up, UART_IER) & UART_IER_UUE)) {
- /*
- * OK it's in a known zero state, try writing and reading
- * without disturbing the current state of the other bits.
- */
- serial_out(up, UART_IER, iersave | UART_IER_UUE);
- if (serial_in(up, UART_IER) & UART_IER_UUE) {
- /*
- * It's an Xscale.
- * We'll leave the UART_IER_UUE bit set to 1 (enabled).
- */
- DEBUG_AUTOCONF("Xscale ");
- up->port.type = PORT_XSCALE;
- up->capabilities |= UART_CAP_UUE | UART_CAP_RTOIE;
- return;
- }
- } else {
- /*
- * If we got here we couldn't force the IER_UUE bit to 0.
- * Log it and continue.
- */
- DEBUG_AUTOCONF("Couldn't force IER_UUE to 0 ");
- }
- serial_out(up, UART_IER, iersave);
-
- /*
- * Exar uarts have EFR in a weird location
- */
- if (up->port.flags & UPF_EXAR_EFR) {
- DEBUG_AUTOCONF("Exar XR17D15x ");
- up->port.type = PORT_XR17D15X;
- up->capabilities |= UART_CAP_AFE | UART_CAP_EFR |
- UART_CAP_SLEEP;
-
- return;
- }
-
- /*
- * We distinguish between 16550A and U6 16550A by counting
- * how many bytes are in the FIFO.
- */
- if (up->port.type == PORT_16550A && size_fifo(up) == 64) {
- up->port.type = PORT_U6_16550A;
- up->capabilities |= UART_CAP_AFE;
- }
-}
-
-/*
- * This routine is called by rs_init() to initialize a specific serial
- * port. It determines what type of UART chip this serial port is
- * using: 8250, 16450, 16550, 16550A. The important question is
- * whether or not this UART is a 16550A or not, since this will
- * determine whether or not we can use its FIFO features or not.
- */
-static void autoconfig(struct uart_8250_port *up)
-{
- unsigned char status1, scratch, scratch2, scratch3;
- unsigned char save_lcr, save_mcr;
- struct uart_port *port = &up->port;
- unsigned long flags;
- unsigned int old_capabilities;
-
- if (!port->iobase && !port->mapbase && !port->membase)
- return;
-
- DEBUG_AUTOCONF("ttyS%d: autoconf (0x%04lx, 0x%p): ",
- serial_index(port), port->iobase, port->membase);
-
- /*
- * We really do need global IRQs disabled here - we're going to
- * be frobbing the chips IRQ enable register to see if it exists.
- */
- spin_lock_irqsave(&port->lock, flags);
-
- up->capabilities = 0;
- up->bugs = 0;
-
- if (!(port->flags & UPF_BUGGY_UART)) {
- /*
- * Do a simple existence test first; if we fail this,
- * there's no point trying anything else.
- *
- * 0x80 is used as a nonsense port to prevent against
- * false positives due to ISA bus float. The
- * assumption is that 0x80 is a non-existent port;
- * which should be safe since include/asm/io.h also
- * makes this assumption.
- *
- * Note: this is safe as long as MCR bit 4 is clear
- * and the device is in "PC" mode.
- */
- scratch = serial_in(up, UART_IER);
- serial_out(up, UART_IER, 0);
-#ifdef __i386__
- outb(0xff, 0x080);
-#endif
- /*
- * Mask out IER[7:4] bits for test as some UARTs (e.g. TL
- * 16C754B) allow only to modify them if an EFR bit is set.
- */
- scratch2 = serial_in(up, UART_IER) & 0x0f;
- serial_out(up, UART_IER, 0x0F);
-#ifdef __i386__
- outb(0, 0x080);
-#endif
- scratch3 = serial_in(up, UART_IER) & 0x0f;
- serial_out(up, UART_IER, scratch);
- if (scratch2 != 0 || scratch3 != 0x0F) {
- /*
- * We failed; there's nothing here
- */
- spin_unlock_irqrestore(&port->lock, flags);
- DEBUG_AUTOCONF("IER test failed (%02x, %02x) ",
- scratch2, scratch3);
- goto out;
- }
- }
-
- save_mcr = serial_in(up, UART_MCR);
- save_lcr = serial_in(up, UART_LCR);
-
- /*
- * Check to see if a UART is really there. Certain broken
- * internal modems based on the Rockwell chipset fail this
- * test, because they apparently don't implement the loopback
- * test mode. So this test is skipped on the COM 1 through
- * COM 4 ports. This *should* be safe, since no board
- * manufacturer would be stupid enough to design a board
- * that conflicts with COM 1-4 --- we hope!
- */
- if (!(port->flags & UPF_SKIP_TEST)) {
- serial_out(up, UART_MCR, UART_MCR_LOOP | 0x0A);
- status1 = serial_in(up, UART_MSR) & 0xF0;
- serial_out(up, UART_MCR, save_mcr);
- if (status1 != 0x90) {
- spin_unlock_irqrestore(&port->lock, flags);
- DEBUG_AUTOCONF("LOOP test failed (%02x) ",
- status1);
- goto out;
- }
- }
-
- /*
- * We're pretty sure there's a port here. Lets find out what
- * type of port it is. The IIR top two bits allows us to find
- * out if it's 8250 or 16450, 16550, 16550A or later. This
- * determines what we test for next.
- *
- * We also initialise the EFR (if any) to zero for later. The
- * EFR occupies the same register location as the FCR and IIR.
- */
- serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
- serial_out(up, UART_EFR, 0);
- serial_out(up, UART_LCR, 0);
-
- serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO);
- scratch = serial_in(up, UART_IIR) >> 6;
-
- switch (scratch) {
- case 0:
- autoconfig_8250(up);
- break;
- case 1:
- port->type = PORT_UNKNOWN;
- break;
- case 2:
- port->type = PORT_16550;
- break;
- case 3:
- autoconfig_16550a(up);
- break;
- }
-
-#ifdef CONFIG_SERIAL_8250_RSA
- /*
- * Only probe for RSA ports if we got the region.
- */
- if (port->type == PORT_16550A && up->probe & UART_PROBE_RSA &&
- __enable_rsa(up))
- port->type = PORT_RSA;
-#endif
-
- serial_out(up, UART_LCR, save_lcr);
-
- port->fifosize = uart_config[up->port.type].fifo_size;
- old_capabilities = up->capabilities;
- up->capabilities = uart_config[port->type].flags;
- up->tx_loadsz = uart_config[port->type].tx_loadsz;
-
- if (port->type == PORT_UNKNOWN)
- goto out_lock;
-
- /*
- * Reset the UART.
- */
-#ifdef CONFIG_SERIAL_8250_RSA
- if (port->type == PORT_RSA)
- serial_out(up, UART_RSA_FRR, 0);
-#endif
- serial_out(up, UART_MCR, save_mcr);
- serial8250_clear_fifos(up);
- serial_in(up, UART_RX);
- if (up->capabilities & UART_CAP_UUE)
- serial_out(up, UART_IER, UART_IER_UUE);
- else
- serial_out(up, UART_IER, 0);
-
-out_lock:
- spin_unlock_irqrestore(&port->lock, flags);
- if (up->capabilities != old_capabilities) {
- printk(KERN_WARNING
- "ttyS%d: detected caps %08x should be %08x\n",
- serial_index(port), old_capabilities,
- up->capabilities);
- }
-out:
- DEBUG_AUTOCONF("iir=%d ", scratch);
- DEBUG_AUTOCONF("type=%s\n", uart_config[port->type].name);
-}
-
-static void autoconfig_irq(struct uart_8250_port *up)
-{
- struct uart_port *port = &up->port;
- unsigned char save_mcr, save_ier;
- unsigned char save_ICP = 0;
- unsigned int ICP = 0;
- unsigned long irqs;
- int irq;
-
- if (port->flags & UPF_FOURPORT) {
- ICP = (port->iobase & 0xfe0) | 0x1f;
- save_ICP = inb_p(ICP);
- outb_p(0x80, ICP);
- inb_p(ICP);
- }
-
- /* forget possible initially masked and pending IRQ */
- probe_irq_off(probe_irq_on());
- save_mcr = serial_in(up, UART_MCR);
- save_ier = serial_in(up, UART_IER);
- serial_out(up, UART_MCR, UART_MCR_OUT1 | UART_MCR_OUT2);
-
- irqs = probe_irq_on();
- serial_out(up, UART_MCR, 0);
- udelay(10);
- if (port->flags & UPF_FOURPORT) {
- serial_out(up, UART_MCR,
- UART_MCR_DTR | UART_MCR_RTS);
- } else {
- serial_out(up, UART_MCR,
- UART_MCR_DTR | UART_MCR_RTS | UART_MCR_OUT2);
- }
- serial_out(up, UART_IER, 0x0f); /* enable all intrs */
- serial_in(up, UART_LSR);
- serial_in(up, UART_RX);
- serial_in(up, UART_IIR);
- serial_in(up, UART_MSR);
- serial_out(up, UART_TX, 0xFF);
- udelay(20);
- irq = probe_irq_off(irqs);
-
- serial_out(up, UART_MCR, save_mcr);
- serial_out(up, UART_IER, save_ier);
-
- if (port->flags & UPF_FOURPORT)
- outb_p(save_ICP, ICP);
-
- port->irq = (irq > 0) ? irq : 0;
-}
-
-static inline void __stop_tx(struct uart_8250_port *p)
-{
- if (p->ier & UART_IER_THRI) {
- p->ier &= ~UART_IER_THRI;
- serial_out(p, UART_IER, p->ier);
- serial8250_rpm_put_tx(p);
- }
-}
-
-static void serial8250_stop_tx(struct uart_port *port)
-{
- struct uart_8250_port *up = up_to_u8250p(port);
-
- serial8250_rpm_get(up);
- __stop_tx(up);
-
- /*
- * We really want to stop the transmitter from sending.
- */
- if (port->type == PORT_16C950) {
- up->acr |= UART_ACR_TXDIS;
- serial_icr_write(up, UART_ACR, up->acr);
- }
- serial8250_rpm_put(up);
-}
-
-static void serial8250_start_tx(struct uart_port *port)
-{
- struct uart_8250_port *up = up_to_u8250p(port);
-
- serial8250_rpm_get_tx(up);
-
- if (up->dma && !up->dma->tx_dma(up))
- return;
-
- if (!(up->ier & UART_IER_THRI)) {
- up->ier |= UART_IER_THRI;
- serial_port_out(port, UART_IER, up->ier);
-
- if (up->bugs & UART_BUG_TXEN) {
- unsigned char lsr;
- lsr = serial_in(up, UART_LSR);
- up->lsr_saved_flags |= lsr & LSR_SAVE_FLAGS;
- if (lsr & UART_LSR_THRE)
- serial8250_tx_chars(up);
- }
- }
-
- /*
- * Re-enable the transmitter if we disabled it.
- */
- if (port->type == PORT_16C950 && up->acr & UART_ACR_TXDIS) {
- up->acr &= ~UART_ACR_TXDIS;
- serial_icr_write(up, UART_ACR, up->acr);
- }
-}
-
-static void serial8250_throttle(struct uart_port *port)
-{
- port->throttle(port);
-}
-
-static void serial8250_unthrottle(struct uart_port *port)
-{
- port->unthrottle(port);
-}
-
-static void serial8250_stop_rx(struct uart_port *port)
-{
- struct uart_8250_port *up = up_to_u8250p(port);
-
- serial8250_rpm_get(up);
-
- up->ier &= ~(UART_IER_RLSI | UART_IER_RDI);
- up->port.read_status_mask &= ~UART_LSR_DR;
- serial_port_out(port, UART_IER, up->ier);
-
- serial8250_rpm_put(up);
-}
-
-static void serial8250_disable_ms(struct uart_port *port)
-{
- struct uart_8250_port *up =
- container_of(port, struct uart_8250_port, port);
-
- /* no MSR capabilities */
- if (up->bugs & UART_BUG_NOMSR)
- return;
-
- up->ier &= ~UART_IER_MSI;
- serial_port_out(port, UART_IER, up->ier);
-}
-
-static void serial8250_enable_ms(struct uart_port *port)
-{
- struct uart_8250_port *up = up_to_u8250p(port);
-
- /* no MSR capabilities */
- if (up->bugs & UART_BUG_NOMSR)
- return;
-
- up->ier |= UART_IER_MSI;
-
- serial8250_rpm_get(up);
- serial_port_out(port, UART_IER, up->ier);
- serial8250_rpm_put(up);
-}
-
-/*
- * serial8250_rx_chars: processes according to the passed in LSR
- * value, and returns the remaining LSR bits not handled
- * by this Rx routine.
- */
-unsigned char
-serial8250_rx_chars(struct uart_8250_port *up, unsigned char lsr)
-{
- struct uart_port *port = &up->port;
- unsigned char ch;
- int max_count = 256;
- char flag;
-
- do {
- if (likely(lsr & UART_LSR_DR))
- ch = serial_in(up, UART_RX);
- else
- /*
- * Intel 82571 has a Serial Over Lan device that will
- * set UART_LSR_BI without setting UART_LSR_DR when
- * it receives a break. To avoid reading from the
- * receive buffer without UART_LSR_DR bit set, we
- * just force the read character to be 0
- */
- ch = 0;
-
- flag = TTY_NORMAL;
- port->icount.rx++;
-
- lsr |= up->lsr_saved_flags;
- up->lsr_saved_flags = 0;
-
- if (unlikely(lsr & UART_LSR_BRK_ERROR_BITS)) {
- if (lsr & UART_LSR_BI) {
- lsr &= ~(UART_LSR_FE | UART_LSR_PE);
- port->icount.brk++;
- /*
- * We do the SysRQ and SAK checking
- * here because otherwise the break
- * may get masked by ignore_status_mask
- * or read_status_mask.
- */
- if (uart_handle_break(port))
- goto ignore_char;
- } else if (lsr & UART_LSR_PE)
- port->icount.parity++;
- else if (lsr & UART_LSR_FE)
- port->icount.frame++;
- if (lsr & UART_LSR_OE)
- port->icount.overrun++;
-
- /*
- * Mask off conditions which should be ignored.
- */
- lsr &= port->read_status_mask;
-
- if (lsr & UART_LSR_BI) {
- DEBUG_INTR("handling break....");
- flag = TTY_BREAK;
- } else if (lsr & UART_LSR_PE)
- flag = TTY_PARITY;
- else if (lsr & UART_LSR_FE)
- flag = TTY_FRAME;
- }
- if (uart_handle_sysrq_char(port, ch))
- goto ignore_char;
-
- uart_insert_char(port, lsr, UART_LSR_OE, ch, flag);
-
-ignore_char:
- lsr = serial_in(up, UART_LSR);
- } while ((lsr & (UART_LSR_DR | UART_LSR_BI)) && (--max_count > 0));
- spin_unlock(&port->lock);
- tty_flip_buffer_push(&port->state->port);
- spin_lock(&port->lock);
- return lsr;
-}
-EXPORT_SYMBOL_GPL(serial8250_rx_chars);
-
-void serial8250_tx_chars(struct uart_8250_port *up)
-{
- struct uart_port *port = &up->port;
- struct circ_buf *xmit = &port->state->xmit;
- int count;
-
- if (port->x_char) {
- serial_out(up, UART_TX, port->x_char);
- port->icount.tx++;
- port->x_char = 0;
- return;
- }
- if (uart_tx_stopped(port)) {
- serial8250_stop_tx(port);
- return;
- }
- if (uart_circ_empty(xmit)) {
- __stop_tx(up);
- return;
- }
-
- count = up->tx_loadsz;
- do {
- serial_out(up, UART_TX, xmit->buf[xmit->tail]);
- xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
- port->icount.tx++;
- if (uart_circ_empty(xmit))
- break;
- if (up->capabilities & UART_CAP_HFIFO) {
- if ((serial_port_in(port, UART_LSR) & BOTH_EMPTY) !=
- BOTH_EMPTY)
- break;
- }
- } while (--count > 0);
-
- if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
- uart_write_wakeup(port);
-
- DEBUG_INTR("THRE...");
-
- /*
- * With RPM enabled, we have to wait until the FIFO is empty before the
- * HW can go idle. So we get here once again with empty FIFO and disable
- * the interrupt and RPM in __stop_tx()
- */
- if (uart_circ_empty(xmit) && !(up->capabilities & UART_CAP_RPM))
- __stop_tx(up);
-}
-EXPORT_SYMBOL_GPL(serial8250_tx_chars);
-
-/* Caller holds uart port lock */
-unsigned int serial8250_modem_status(struct uart_8250_port *up)
-{
- struct uart_port *port = &up->port;
- unsigned int status = serial_in(up, UART_MSR);
-
- status |= up->msr_saved_flags;
- up->msr_saved_flags = 0;
- if (status & UART_MSR_ANY_DELTA && up->ier & UART_IER_MSI &&
- port->state != NULL) {
- if (status & UART_MSR_TERI)
- port->icount.rng++;
- if (status & UART_MSR_DDSR)
- port->icount.dsr++;
- if (status & UART_MSR_DDCD)
- uart_handle_dcd_change(port, status & UART_MSR_DCD);
- if (status & UART_MSR_DCTS)
- uart_handle_cts_change(port, status & UART_MSR_CTS);
-
- wake_up_interruptible(&port->state->port.delta_msr_wait);
- }
-
- return status;
-}
-EXPORT_SYMBOL_GPL(serial8250_modem_status);
-
-/*
- * This handles the interrupt from one port.
- */
-int serial8250_handle_irq(struct uart_port *port, unsigned int iir)
-{
- unsigned char status;
- unsigned long flags;
- struct uart_8250_port *up = up_to_u8250p(port);
- int dma_err = 0;
-
- if (iir & UART_IIR_NO_INT)
- return 0;
-
- spin_lock_irqsave(&port->lock, flags);
-
- status = serial_port_in(port, UART_LSR);
-
- DEBUG_INTR("status = %x...", status);
-
- if (status & (UART_LSR_DR | UART_LSR_BI)) {
- if (up->dma)
- dma_err = up->dma->rx_dma(up, iir);
-
- if (!up->dma || dma_err)
- status = serial8250_rx_chars(up, status);
- }
- serial8250_modem_status(up);
- if ((!up->dma || (up->dma && up->dma->tx_err)) &&
- (status & UART_LSR_THRE))
- serial8250_tx_chars(up);
-
- spin_unlock_irqrestore(&port->lock, flags);
- return 1;
-}
-EXPORT_SYMBOL_GPL(serial8250_handle_irq);
-
-static int serial8250_default_handle_irq(struct uart_port *port)
-{
- struct uart_8250_port *up = up_to_u8250p(port);
- unsigned int iir;
- int ret;
-
- serial8250_rpm_get(up);
-
- iir = serial_port_in(port, UART_IIR);
- ret = serial8250_handle_irq(port, iir);
-
- serial8250_rpm_put(up);
- return ret;
-}
-
-/*
- * These Exar UARTs have an extra interrupt indicator that could
- * fire for a few unimplemented interrupts. One of which is a
- * wakeup event when coming out of sleep. Put this here just
- * to be on the safe side that these interrupts don't go unhandled.
- */
-static int exar_handle_irq(struct uart_port *port)
-{
- unsigned char int0, int1, int2, int3;
- unsigned int iir = serial_port_in(port, UART_IIR);
- int ret;
-
- ret = serial8250_handle_irq(port, iir);
-
- if ((port->type == PORT_XR17V35X) ||
- (port->type == PORT_XR17D15X)) {
- int0 = serial_port_in(port, 0x80);
- int1 = serial_port_in(port, 0x81);
- int2 = serial_port_in(port, 0x82);
- int3 = serial_port_in(port, 0x83);
- }
-
- return ret;
-}
-
-/*
* This is the serial driver's interrupt routine.
*
* Arjan thinks the old way was overly complex, so it got simplified.
@@ -1941,876 +359,6 @@
serial_unlink_irq_chain(up);
}
-static unsigned int serial8250_tx_empty(struct uart_port *port)
-{
- struct uart_8250_port *up = up_to_u8250p(port);
- unsigned long flags;
- unsigned int lsr;
-
- serial8250_rpm_get(up);
-
- spin_lock_irqsave(&port->lock, flags);
- lsr = serial_port_in(port, UART_LSR);
- up->lsr_saved_flags |= lsr & LSR_SAVE_FLAGS;
- spin_unlock_irqrestore(&port->lock, flags);
-
- serial8250_rpm_put(up);
-
- return (lsr & BOTH_EMPTY) == BOTH_EMPTY ? TIOCSER_TEMT : 0;
-}
-
-static unsigned int serial8250_get_mctrl(struct uart_port *port)
-{
- struct uart_8250_port *up = up_to_u8250p(port);
- unsigned int status;
- unsigned int ret;
-
- serial8250_rpm_get(up);
- status = serial8250_modem_status(up);
- serial8250_rpm_put(up);
-
- ret = 0;
- if (status & UART_MSR_DCD)
- ret |= TIOCM_CAR;
- if (status & UART_MSR_RI)
- ret |= TIOCM_RNG;
- if (status & UART_MSR_DSR)
- ret |= TIOCM_DSR;
- if (status & UART_MSR_CTS)
- ret |= TIOCM_CTS;
- return ret;
-}
-
-void serial8250_do_set_mctrl(struct uart_port *port, unsigned int mctrl)
-{
- struct uart_8250_port *up = up_to_u8250p(port);
- unsigned char mcr = 0;
-
- if (mctrl & TIOCM_RTS)
- mcr |= UART_MCR_RTS;
- if (mctrl & TIOCM_DTR)
- mcr |= UART_MCR_DTR;
- if (mctrl & TIOCM_OUT1)
- mcr |= UART_MCR_OUT1;
- if (mctrl & TIOCM_OUT2)
- mcr |= UART_MCR_OUT2;
- if (mctrl & TIOCM_LOOP)
- mcr |= UART_MCR_LOOP;
-
- mcr = (mcr & up->mcr_mask) | up->mcr_force | up->mcr;
-
- serial_port_out(port, UART_MCR, mcr);
-}
-EXPORT_SYMBOL_GPL(serial8250_do_set_mctrl);
-
-static void serial8250_set_mctrl(struct uart_port *port, unsigned int mctrl)
-{
- if (port->set_mctrl)
- port->set_mctrl(port, mctrl);
- else
- serial8250_do_set_mctrl(port, mctrl);
-}
-
-static void serial8250_break_ctl(struct uart_port *port, int break_state)
-{
- struct uart_8250_port *up = up_to_u8250p(port);
- unsigned long flags;
-
- serial8250_rpm_get(up);
- spin_lock_irqsave(&port->lock, flags);
- if (break_state == -1)
- up->lcr |= UART_LCR_SBC;
- else
- up->lcr &= ~UART_LCR_SBC;
- serial_port_out(port, UART_LCR, up->lcr);
- spin_unlock_irqrestore(&port->lock, flags);
- serial8250_rpm_put(up);
-}
-
-/*
- * Wait for transmitter & holding register to empty
- */
-static void wait_for_xmitr(struct uart_8250_port *up, int bits)
-{
- unsigned int status, tmout = 10000;
-
- /* Wait up to 10ms for the character(s) to be sent. */
- for (;;) {
- status = serial_in(up, UART_LSR);
-
- up->lsr_saved_flags |= status & LSR_SAVE_FLAGS;
-
- if ((status & bits) == bits)
- break;
- if (--tmout == 0)
- break;
- udelay(1);
- }
-
- /* Wait up to 1s for flow control if necessary */
- if (up->port.flags & UPF_CONS_FLOW) {
- unsigned int tmout;
- for (tmout = 1000000; tmout; tmout--) {
- unsigned int msr = serial_in(up, UART_MSR);
- up->msr_saved_flags |= msr & MSR_SAVE_FLAGS;
- if (msr & UART_MSR_CTS)
- break;
- udelay(1);
- touch_nmi_watchdog();
- }
- }
-}
-
-#ifdef CONFIG_CONSOLE_POLL
-/*
- * Console polling routines for writing and reading from the uart while
- * in an interrupt or debug context.
- */
-
-static int serial8250_get_poll_char(struct uart_port *port)
-{
- struct uart_8250_port *up = up_to_u8250p(port);
- unsigned char lsr;
- int status;
-
- serial8250_rpm_get(up);
-
- lsr = serial_port_in(port, UART_LSR);
-
- if (!(lsr & UART_LSR_DR)) {
- status = NO_POLL_CHAR;
- goto out;
- }
-
- status = serial_port_in(port, UART_RX);
-out:
- serial8250_rpm_put(up);
- return status;
-}
-
-
-static void serial8250_put_poll_char(struct uart_port *port,
- unsigned char c)
-{
- unsigned int ier;
- struct uart_8250_port *up = up_to_u8250p(port);
-
- serial8250_rpm_get(up);
- /*
- * First save the IER then disable the interrupts
- */
- ier = serial_port_in(port, UART_IER);
- if (up->capabilities & UART_CAP_UUE)
- serial_port_out(port, UART_IER, UART_IER_UUE);
- else
- serial_port_out(port, UART_IER, 0);
-
- wait_for_xmitr(up, BOTH_EMPTY);
- /*
- * Send the character out.
- */
- serial_port_out(port, UART_TX, c);
-
- /*
- * Finally, wait for transmitter to become empty
- * and restore the IER
- */
- wait_for_xmitr(up, BOTH_EMPTY);
- serial_port_out(port, UART_IER, ier);
- serial8250_rpm_put(up);
-}
-
-#endif /* CONFIG_CONSOLE_POLL */
-
-int serial8250_do_startup(struct uart_port *port)
-{
- struct uart_8250_port *up = up_to_u8250p(port);
- unsigned long flags;
- unsigned char lsr, iir;
- int retval;
-
- if (port->type == PORT_8250_CIR)
- return -ENODEV;
-
- if (!port->fifosize)
- port->fifosize = uart_config[port->type].fifo_size;
- if (!up->tx_loadsz)
- up->tx_loadsz = uart_config[port->type].tx_loadsz;
- if (!up->capabilities)
- up->capabilities = uart_config[port->type].flags;
- up->mcr = 0;
-
- if (port->iotype != up->cur_iotype)
- set_io_from_upio(port);
-
- serial8250_rpm_get(up);
- if (port->type == PORT_16C950) {
- /* Wake up and initialize UART */
- up->acr = 0;
- serial_port_out(port, UART_LCR, UART_LCR_CONF_MODE_B);
- serial_port_out(port, UART_EFR, UART_EFR_ECB);
- serial_port_out(port, UART_IER, 0);
- serial_port_out(port, UART_LCR, 0);
- serial_icr_write(up, UART_CSR, 0); /* Reset the UART */
- serial_port_out(port, UART_LCR, UART_LCR_CONF_MODE_B);
- serial_port_out(port, UART_EFR, UART_EFR_ECB);
- serial_port_out(port, UART_LCR, 0);
- }
-
-#ifdef CONFIG_SERIAL_8250_RSA
- /*
- * If this is an RSA port, see if we can kick it up to the
- * higher speed clock.
- */
- enable_rsa(up);
-#endif
- /*
- * Clear the FIFO buffers and disable them.
- * (they will be reenabled in set_termios())
- */
- serial8250_clear_fifos(up);
-
- /*
- * Clear the interrupt registers.
- */
- serial_port_in(port, UART_LSR);
- serial_port_in(port, UART_RX);
- serial_port_in(port, UART_IIR);
- serial_port_in(port, UART_MSR);
-
- /*
- * At this point, there's no way the LSR could still be 0xff;
- * if it is, then bail out, because there's likely no UART
- * here.
- */
- if (!(port->flags & UPF_BUGGY_UART) &&
- (serial_port_in(port, UART_LSR) == 0xff)) {
- printk_ratelimited(KERN_INFO "ttyS%d: LSR safety check engaged!\n",
- serial_index(port));
- retval = -ENODEV;
- goto out;
- }
-
- /*
- * For a XR16C850, we need to set the trigger levels
- */
- if (port->type == PORT_16850) {
- unsigned char fctr;
-
- serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
-
- fctr = serial_in(up, UART_FCTR) & ~(UART_FCTR_RX|UART_FCTR_TX);
- serial_port_out(port, UART_FCTR,
- fctr | UART_FCTR_TRGD | UART_FCTR_RX);
- serial_port_out(port, UART_TRG, UART_TRG_96);
- serial_port_out(port, UART_FCTR,
- fctr | UART_FCTR_TRGD | UART_FCTR_TX);
- serial_port_out(port, UART_TRG, UART_TRG_96);
-
- serial_port_out(port, UART_LCR, 0);
- }
-
- if (port->irq) {
- unsigned char iir1;
- /*
- * Test for UARTs that do not reassert THRE when the
- * transmitter is idle and the interrupt has already
- * been cleared. Real 16550s should always reassert
- * this interrupt whenever the transmitter is idle and
- * the interrupt is enabled. Delays are necessary to
- * allow register changes to become visible.
- */
- spin_lock_irqsave(&port->lock, flags);
- if (up->port.irqflags & IRQF_SHARED)
- disable_irq_nosync(port->irq);
-
- wait_for_xmitr(up, UART_LSR_THRE);
- serial_port_out_sync(port, UART_IER, UART_IER_THRI);
- udelay(1); /* allow THRE to set */
- iir1 = serial_port_in(port, UART_IIR);
- serial_port_out(port, UART_IER, 0);
- serial_port_out_sync(port, UART_IER, UART_IER_THRI);
- udelay(1); /* allow a working UART time to re-assert THRE */
- iir = serial_port_in(port, UART_IIR);
- serial_port_out(port, UART_IER, 0);
-
- if (port->irqflags & IRQF_SHARED)
- enable_irq(port->irq);
- spin_unlock_irqrestore(&port->lock, flags);
-
- /*
- * If the interrupt is not reasserted, or we otherwise
- * don't trust the iir, setup a timer to kick the UART
- * on a regular basis.
- */
- if ((!(iir1 & UART_IIR_NO_INT) && (iir & UART_IIR_NO_INT)) ||
- up->port.flags & UPF_BUG_THRE) {
- up->bugs |= UART_BUG_THRE;
- }
- }
-
- retval = up->ops->setup_irq(up);
- if (retval)
- goto out;
-
- /*
- * Now, initialize the UART
- */
- serial_port_out(port, UART_LCR, UART_LCR_WLEN8);
-
- spin_lock_irqsave(&port->lock, flags);
- if (up->port.flags & UPF_FOURPORT) {
- if (!up->port.irq)
- up->port.mctrl |= TIOCM_OUT1;
- } else
- /*
- * Most PC uarts need OUT2 raised to enable interrupts.
- */
- if (port->irq)
- up->port.mctrl |= TIOCM_OUT2;
-
- serial8250_set_mctrl(port, port->mctrl);
-
- /* Serial over Lan (SoL) hack:
- Intel 8257x Gigabit ethernet chips have a
- 16550 emulation, to be used for Serial Over Lan.
- Those chips take a longer time than a normal
- serial device to signalize that a transmission
- data was queued. Due to that, the above test generally
- fails. One solution would be to delay the reading of
- iir. However, this is not reliable, since the timeout
- is variable. So, let's just don't test if we receive
- TX irq. This way, we'll never enable UART_BUG_TXEN.
- */
- if (up->port.flags & UPF_NO_TXEN_TEST)
- goto dont_test_tx_en;
-
- /*
- * Do a quick test to see if we receive an
- * interrupt when we enable the TX irq.
- */
- serial_port_out(port, UART_IER, UART_IER_THRI);
- lsr = serial_port_in(port, UART_LSR);
- iir = serial_port_in(port, UART_IIR);
- serial_port_out(port, UART_IER, 0);
-
- if (lsr & UART_LSR_TEMT && iir & UART_IIR_NO_INT) {
- if (!(up->bugs & UART_BUG_TXEN)) {
- up->bugs |= UART_BUG_TXEN;
- pr_debug("ttyS%d - enabling bad tx status workarounds\n",
- serial_index(port));
- }
- } else {
- up->bugs &= ~UART_BUG_TXEN;
- }
-
-dont_test_tx_en:
- spin_unlock_irqrestore(&port->lock, flags);
-
- /*
- * Clear the interrupt registers again for luck, and clear the
- * saved flags to avoid getting false values from polling
- * routines or the previous session.
- */
- serial_port_in(port, UART_LSR);
- serial_port_in(port, UART_RX);
- serial_port_in(port, UART_IIR);
- serial_port_in(port, UART_MSR);
- up->lsr_saved_flags = 0;
- up->msr_saved_flags = 0;
-
- /*
- * Request DMA channels for both RX and TX.
- */
- if (up->dma) {
- retval = serial8250_request_dma(up);
- if (retval) {
- pr_warn_ratelimited("ttyS%d - failed to request DMA\n",
- serial_index(port));
- up->dma = NULL;
- }
- }
-
- /*
- * Finally, enable interrupts. Note: Modem status interrupts
- * are set via set_termios(), which will be occurring imminently
- * anyway, so we don't enable them here.
- */
- up->ier = UART_IER_RLSI | UART_IER_RDI;
- serial_port_out(port, UART_IER, up->ier);
-
- if (port->flags & UPF_FOURPORT) {
- unsigned int icp;
- /*
- * Enable interrupts on the AST Fourport board
- */
- icp = (port->iobase & 0xfe0) | 0x01f;
- outb_p(0x80, icp);
- inb_p(icp);
- }
- retval = 0;
-out:
- serial8250_rpm_put(up);
- return retval;
-}
-EXPORT_SYMBOL_GPL(serial8250_do_startup);
-
-static int serial8250_startup(struct uart_port *port)
-{
- if (port->startup)
- return port->startup(port);
- return serial8250_do_startup(port);
-}
-
-void serial8250_do_shutdown(struct uart_port *port)
-{
- struct uart_8250_port *up = up_to_u8250p(port);
- unsigned long flags;
-
- serial8250_rpm_get(up);
- /*
- * Disable interrupts from this port
- */
- up->ier = 0;
- serial_port_out(port, UART_IER, 0);
-
- if (up->dma)
- serial8250_release_dma(up);
-
- spin_lock_irqsave(&port->lock, flags);
- if (port->flags & UPF_FOURPORT) {
- /* reset interrupts on the AST Fourport board */
- inb((port->iobase & 0xfe0) | 0x1f);
- port->mctrl |= TIOCM_OUT1;
- } else
- port->mctrl &= ~TIOCM_OUT2;
-
- serial8250_set_mctrl(port, port->mctrl);
- spin_unlock_irqrestore(&port->lock, flags);
-
- /*
- * Disable break condition and FIFOs
- */
- serial_port_out(port, UART_LCR,
- serial_port_in(port, UART_LCR) & ~UART_LCR_SBC);
- serial8250_clear_fifos(up);
-
-#ifdef CONFIG_SERIAL_8250_RSA
- /*
- * Reset the RSA board back to 115kbps compat mode.
- */
- disable_rsa(up);
-#endif
-
- /*
- * Read data port to reset things, and then unlink from
- * the IRQ chain.
- */
- serial_port_in(port, UART_RX);
- serial8250_rpm_put(up);
-
- up->ops->release_irq(up);
-}
-EXPORT_SYMBOL_GPL(serial8250_do_shutdown);
-
-static void serial8250_shutdown(struct uart_port *port)
-{
- if (port->shutdown)
- port->shutdown(port);
- else
- serial8250_do_shutdown(port);
-}
-
-/*
- * XR17V35x UARTs have an extra fractional divisor register (DLD)
- * Calculate divisor with extra 4-bit fractional portion
- */
-static unsigned int xr17v35x_get_divisor(struct uart_8250_port *up,
- unsigned int baud,
- unsigned int *frac)
-{
- struct uart_port *port = &up->port;
- unsigned int quot_16;
-
- quot_16 = DIV_ROUND_CLOSEST(port->uartclk, baud);
- *frac = quot_16 & 0x0f;
-
- return quot_16 >> 4;
-}
-
-static unsigned int serial8250_get_divisor(struct uart_8250_port *up,
- unsigned int baud,
- unsigned int *frac)
-{
- struct uart_port *port = &up->port;
- unsigned int quot;
-
- /*
- * Handle magic divisors for baud rates above baud_base on
- * SMSC SuperIO chips.
- *
- */
- if ((port->flags & UPF_MAGIC_MULTIPLIER) &&
- baud == (port->uartclk/4))
- quot = 0x8001;
- else if ((port->flags & UPF_MAGIC_MULTIPLIER) &&
- baud == (port->uartclk/8))
- quot = 0x8002;
- else if (up->port.type == PORT_XR17V35X)
- quot = xr17v35x_get_divisor(up, baud, frac);
- else
- quot = uart_get_divisor(port, baud);
-
- /*
- * Oxford Semi 952 rev B workaround
- */
- if (up->bugs & UART_BUG_QUOT && (quot & 0xff) == 0)
- quot++;
-
- return quot;
-}
-
-static unsigned char serial8250_compute_lcr(struct uart_8250_port *up,
- tcflag_t c_cflag)
-{
- unsigned char cval;
-
- switch (c_cflag & CSIZE) {
- case CS5:
- cval = UART_LCR_WLEN5;
- break;
- case CS6:
- cval = UART_LCR_WLEN6;
- break;
- case CS7:
- cval = UART_LCR_WLEN7;
- break;
- default:
- case CS8:
- cval = UART_LCR_WLEN8;
- break;
- }
-
- if (c_cflag & CSTOPB)
- cval |= UART_LCR_STOP;
- if (c_cflag & PARENB) {
- cval |= UART_LCR_PARITY;
- if (up->bugs & UART_BUG_PARITY)
- up->fifo_bug = true;
- }
- if (!(c_cflag & PARODD))
- cval |= UART_LCR_EPAR;
-#ifdef CMSPAR
- if (c_cflag & CMSPAR)
- cval |= UART_LCR_SPAR;
-#endif
-
- return cval;
-}
-
-static void serial8250_set_divisor(struct uart_port *port, unsigned int baud,
- unsigned int quot, unsigned int quot_frac)
-{
- struct uart_8250_port *up = up_to_u8250p(port);
-
- /* Workaround to enable 115200 baud on OMAP1510 internal ports */
- if (is_omap1510_8250(up)) {
- if (baud == 115200) {
- quot = 1;
- serial_port_out(port, UART_OMAP_OSC_12M_SEL, 1);
- } else
- serial_port_out(port, UART_OMAP_OSC_12M_SEL, 0);
- }
-
- /*
- * For NatSemi, switch to bank 2 not bank 1, to avoid resetting EXCR2,
- * otherwise just set DLAB
- */
- if (up->capabilities & UART_NATSEMI)
- serial_port_out(port, UART_LCR, 0xe0);
- else
- serial_port_out(port, UART_LCR, up->lcr | UART_LCR_DLAB);
-
- serial_dl_write(up, quot);
-
- /* XR17V35x UARTs have an extra fractional divisor register (DLD) */
- if (up->port.type == PORT_XR17V35X)
- serial_port_out(port, 0x2, quot_frac);
-}
-
-void
-serial8250_do_set_termios(struct uart_port *port, struct ktermios *termios,
- struct ktermios *old)
-{
- struct uart_8250_port *up = up_to_u8250p(port);
- unsigned char cval;
- unsigned long flags;
- unsigned int baud, quot, frac = 0;
-
- cval = serial8250_compute_lcr(up, termios->c_cflag);
-
- /*
- * Ask the core to calculate the divisor for us.
- */
- baud = uart_get_baud_rate(port, termios, old,
- port->uartclk / 16 / 0xffff,
- port->uartclk / 16);
- quot = serial8250_get_divisor(up, baud, &frac);
-
- /*
- * Ok, we're now changing the port state. Do it with
- * interrupts disabled.
- */
- serial8250_rpm_get(up);
- spin_lock_irqsave(&port->lock, flags);
-
- up->lcr = cval; /* Save computed LCR */
-
- if (up->capabilities & UART_CAP_FIFO && port->fifosize > 1) {
- /* NOTE: If fifo_bug is not set, a user can set RX_trigger. */
- if ((baud < 2400 && !up->dma) || up->fifo_bug) {
- up->fcr &= ~UART_FCR_TRIGGER_MASK;
- up->fcr |= UART_FCR_TRIGGER_1;
- }
- }
-
- /*
- * MCR-based auto flow control. When AFE is enabled, RTS will be
- * deasserted when the receive FIFO contains more characters than
- * the trigger, or the MCR RTS bit is cleared. In the case where
- * the remote UART is not using CTS auto flow control, we must
- * have sufficient FIFO entries for the latency of the remote
- * UART to respond. IOW, at least 32 bytes of FIFO.
- */
- if (up->capabilities & UART_CAP_AFE && port->fifosize >= 32) {
- up->mcr &= ~UART_MCR_AFE;
- if (termios->c_cflag & CRTSCTS)
- up->mcr |= UART_MCR_AFE;
- }
-
- /*
- * Update the per-port timeout.
- */
- uart_update_timeout(port, termios->c_cflag, baud);
-
- port->read_status_mask = UART_LSR_OE | UART_LSR_THRE | UART_LSR_DR;
- if (termios->c_iflag & INPCK)
- port->read_status_mask |= UART_LSR_FE | UART_LSR_PE;
- if (termios->c_iflag & (IGNBRK | BRKINT | PARMRK))
- port->read_status_mask |= UART_LSR_BI;
-
- /*
- * Characteres to ignore
- */
- port->ignore_status_mask = 0;
- if (termios->c_iflag & IGNPAR)
- port->ignore_status_mask |= UART_LSR_PE | UART_LSR_FE;
- if (termios->c_iflag & IGNBRK) {
- port->ignore_status_mask |= UART_LSR_BI;
- /*
- * If we're ignoring parity and break indicators,
- * ignore overruns too (for real raw support).
- */
- if (termios->c_iflag & IGNPAR)
- port->ignore_status_mask |= UART_LSR_OE;
- }
-
- /*
- * ignore all characters if CREAD is not set
- */
- if ((termios->c_cflag & CREAD) == 0)
- port->ignore_status_mask |= UART_LSR_DR;
-
- /*
- * CTS flow control flag and modem status interrupts
- */
- up->ier &= ~UART_IER_MSI;
- if (!(up->bugs & UART_BUG_NOMSR) &&
- UART_ENABLE_MS(&up->port, termios->c_cflag))
- up->ier |= UART_IER_MSI;
- if (up->capabilities & UART_CAP_UUE)
- up->ier |= UART_IER_UUE;
- if (up->capabilities & UART_CAP_RTOIE)
- up->ier |= UART_IER_RTOIE;
-
- serial_port_out(port, UART_IER, up->ier);
-
- if (up->capabilities & UART_CAP_EFR) {
- unsigned char efr = 0;
- /*
- * TI16C752/Startech hardware flow control. FIXME:
- * - TI16C752 requires control thresholds to be set.
- * - UART_MCR_RTS is ineffective if auto-RTS mode is enabled.
- */
- if (termios->c_cflag & CRTSCTS)
- efr |= UART_EFR_CTS;
-
- serial_port_out(port, UART_LCR, UART_LCR_CONF_MODE_B);
- if (port->flags & UPF_EXAR_EFR)
- serial_port_out(port, UART_XR_EFR, efr);
- else
- serial_port_out(port, UART_EFR, efr);
- }
-
- serial8250_set_divisor(port, baud, quot, frac);
-
- /*
- * LCR DLAB must be set to enable 64-byte FIFO mode. If the FCR
- * is written without DLAB set, this mode will be disabled.
- */
- if (port->type == PORT_16750)
- serial_port_out(port, UART_FCR, up->fcr);
-
- serial_port_out(port, UART_LCR, up->lcr); /* reset DLAB */
- if (port->type != PORT_16750) {
- /* emulated UARTs (Lucent Venus 167x) need two steps */
- if (up->fcr & UART_FCR_ENABLE_FIFO)
- serial_port_out(port, UART_FCR, UART_FCR_ENABLE_FIFO);
- serial_port_out(port, UART_FCR, up->fcr); /* set fcr */
- }
- serial8250_set_mctrl(port, port->mctrl);
- spin_unlock_irqrestore(&port->lock, flags);
- serial8250_rpm_put(up);
-
- /* Don't rewrite B0 */
- if (tty_termios_baud_rate(termios))
- tty_termios_encode_baud_rate(termios, baud, baud);
-}
-EXPORT_SYMBOL(serial8250_do_set_termios);
-
-static void
-serial8250_set_termios(struct uart_port *port, struct ktermios *termios,
- struct ktermios *old)
-{
- if (port->set_termios)
- port->set_termios(port, termios, old);
- else
- serial8250_do_set_termios(port, termios, old);
-}
-
-static void
-serial8250_set_ldisc(struct uart_port *port, struct ktermios *termios)
-{
- if (termios->c_line == N_PPS) {
- port->flags |= UPF_HARDPPS_CD;
- spin_lock_irq(&port->lock);
- serial8250_enable_ms(port);
- spin_unlock_irq(&port->lock);
- } else {
- port->flags &= ~UPF_HARDPPS_CD;
- if (!UART_ENABLE_MS(port, termios->c_cflag)) {
- spin_lock_irq(&port->lock);
- serial8250_disable_ms(port);
- spin_unlock_irq(&port->lock);
- }
- }
-}
-
-
-void serial8250_do_pm(struct uart_port *port, unsigned int state,
- unsigned int oldstate)
-{
- struct uart_8250_port *p = up_to_u8250p(port);
-
- serial8250_set_sleep(p, state != 0);
-}
-EXPORT_SYMBOL(serial8250_do_pm);
-
-static void
-serial8250_pm(struct uart_port *port, unsigned int state,
- unsigned int oldstate)
-{
- if (port->pm)
- port->pm(port, state, oldstate);
- else
- serial8250_do_pm(port, state, oldstate);
-}
-
-static unsigned int serial8250_port_size(struct uart_8250_port *pt)
-{
- if (pt->port.mapsize)
- return pt->port.mapsize;
- if (pt->port.iotype == UPIO_AU) {
- if (pt->port.type == PORT_RT2880)
- return 0x100;
- return 0x1000;
- }
- if (is_omap1_8250(pt))
- return 0x16 << pt->port.regshift;
-
- return 8 << pt->port.regshift;
-}
-
-/*
- * Resource handling.
- */
-static int serial8250_request_std_resource(struct uart_8250_port *up)
-{
- unsigned int size = serial8250_port_size(up);
- struct uart_port *port = &up->port;
- int ret = 0;
-
- switch (port->iotype) {
- case UPIO_AU:
- case UPIO_TSI:
- case UPIO_MEM32:
- case UPIO_MEM32BE:
- case UPIO_MEM:
- if (!port->mapbase)
- break;
-
- if (!request_mem_region(port->mapbase, size, "serial")) {
- ret = -EBUSY;
- break;
- }
-
- if (port->flags & UPF_IOREMAP) {
- port->membase = ioremap_nocache(port->mapbase, size);
- if (!port->membase) {
- release_mem_region(port->mapbase, size);
- ret = -ENOMEM;
- }
- }
- break;
-
- case UPIO_HUB6:
- case UPIO_PORT:
- if (!request_region(port->iobase, size, "serial"))
- ret = -EBUSY;
- break;
- }
- return ret;
-}
-
-static void serial8250_release_std_resource(struct uart_8250_port *up)
-{
- unsigned int size = serial8250_port_size(up);
- struct uart_port *port = &up->port;
-
- switch (port->iotype) {
- case UPIO_AU:
- case UPIO_TSI:
- case UPIO_MEM32:
- case UPIO_MEM32BE:
- case UPIO_MEM:
- if (!port->mapbase)
- break;
-
- if (port->flags & UPF_IOREMAP) {
- iounmap(port->membase);
- port->membase = NULL;
- }
-
- release_mem_region(port->mapbase, size);
- break;
-
- case UPIO_HUB6:
- case UPIO_PORT:
- release_region(port->iobase, size);
- break;
- }
-}
-
#ifdef CONFIG_SERIAL_8250_RSA
static int serial8250_request_rsa_resource(struct uart_8250_port *up)
{
@@ -2848,259 +396,6 @@
}
#endif
-static void serial8250_release_port(struct uart_port *port)
-{
- struct uart_8250_port *up = up_to_u8250p(port);
-
- serial8250_release_std_resource(up);
-}
-
-static int serial8250_request_port(struct uart_port *port)
-{
- struct uart_8250_port *up = up_to_u8250p(port);
- int ret;
-
- if (port->type == PORT_8250_CIR)
- return -ENODEV;
-
- ret = serial8250_request_std_resource(up);
-
- return ret;
-}
-
-static int fcr_get_rxtrig_bytes(struct uart_8250_port *up)
-{
- const struct serial8250_config *conf_type = &uart_config[up->port.type];
- unsigned char bytes;
-
- bytes = conf_type->rxtrig_bytes[UART_FCR_R_TRIG_BITS(up->fcr)];
-
- return bytes ? bytes : -EOPNOTSUPP;
-}
-
-static int bytes_to_fcr_rxtrig(struct uart_8250_port *up, unsigned char bytes)
-{
- const struct serial8250_config *conf_type = &uart_config[up->port.type];
- int i;
-
- if (!conf_type->rxtrig_bytes[UART_FCR_R_TRIG_BITS(UART_FCR_R_TRIG_00)])
- return -EOPNOTSUPP;
-
- for (i = 1; i < UART_FCR_R_TRIG_MAX_STATE; i++) {
- if (bytes < conf_type->rxtrig_bytes[i])
- /* Use the nearest lower value */
- return (--i) << UART_FCR_R_TRIG_SHIFT;
- }
-
- return UART_FCR_R_TRIG_11;
-}
-
-static int do_get_rxtrig(struct tty_port *port)
-{
- struct uart_state *state = container_of(port, struct uart_state, port);
- struct uart_port *uport = state->uart_port;
- struct uart_8250_port *up =
- container_of(uport, struct uart_8250_port, port);
-
- if (!(up->capabilities & UART_CAP_FIFO) || uport->fifosize <= 1)
- return -EINVAL;
-
- return fcr_get_rxtrig_bytes(up);
-}
-
-static int do_serial8250_get_rxtrig(struct tty_port *port)
-{
- int rxtrig_bytes;
-
- mutex_lock(&port->mutex);
- rxtrig_bytes = do_get_rxtrig(port);
- mutex_unlock(&port->mutex);
-
- return rxtrig_bytes;
-}
-
-static ssize_t serial8250_get_attr_rx_trig_bytes(struct device *dev,
- struct device_attribute *attr, char *buf)
-{
- struct tty_port *port = dev_get_drvdata(dev);
- int rxtrig_bytes;
-
- rxtrig_bytes = do_serial8250_get_rxtrig(port);
- if (rxtrig_bytes < 0)
- return rxtrig_bytes;
-
- return snprintf(buf, PAGE_SIZE, "%d\n", rxtrig_bytes);
-}
-
-static int do_set_rxtrig(struct tty_port *port, unsigned char bytes)
-{
- struct uart_state *state = container_of(port, struct uart_state, port);
- struct uart_port *uport = state->uart_port;
- struct uart_8250_port *up =
- container_of(uport, struct uart_8250_port, port);
- int rxtrig;
-
- if (!(up->capabilities & UART_CAP_FIFO) || uport->fifosize <= 1 ||
- up->fifo_bug)
- return -EINVAL;
-
- rxtrig = bytes_to_fcr_rxtrig(up, bytes);
- if (rxtrig < 0)
- return rxtrig;
-
- serial8250_clear_fifos(up);
- up->fcr &= ~UART_FCR_TRIGGER_MASK;
- up->fcr |= (unsigned char)rxtrig;
- serial_out(up, UART_FCR, up->fcr);
- return 0;
-}
-
-static int do_serial8250_set_rxtrig(struct tty_port *port, unsigned char bytes)
-{
- int ret;
-
- mutex_lock(&port->mutex);
- ret = do_set_rxtrig(port, bytes);
- mutex_unlock(&port->mutex);
-
- return ret;
-}
-
-static ssize_t serial8250_set_attr_rx_trig_bytes(struct device *dev,
- struct device_attribute *attr, const char *buf, size_t count)
-{
- struct tty_port *port = dev_get_drvdata(dev);
- unsigned char bytes;
- int ret;
-
- if (!count)
- return -EINVAL;
-
- ret = kstrtou8(buf, 10, &bytes);
- if (ret < 0)
- return ret;
-
- ret = do_serial8250_set_rxtrig(port, bytes);
- if (ret < 0)
- return ret;
-
- return count;
-}
-
-static DEVICE_ATTR(rx_trig_bytes, S_IRUSR | S_IWUSR | S_IRGRP,
- serial8250_get_attr_rx_trig_bytes,
- serial8250_set_attr_rx_trig_bytes);
-
-static struct attribute *serial8250_dev_attrs[] = {
- &dev_attr_rx_trig_bytes.attr,
- NULL,
- };
-
-static struct attribute_group serial8250_dev_attr_group = {
- .attrs = serial8250_dev_attrs,
- };
-
-static void register_dev_spec_attr_grp(struct uart_8250_port *up)
-{
- const struct serial8250_config *conf_type = &uart_config[up->port.type];
-
- if (conf_type->rxtrig_bytes[0])
- up->port.attr_group = &serial8250_dev_attr_group;
-}
-
-static void serial8250_config_port(struct uart_port *port, int flags)
-{
- struct uart_8250_port *up = up_to_u8250p(port);
- int ret;
-
- if (port->type == PORT_8250_CIR)
- return;
-
- /*
- * Find the region that we can probe for. This in turn
- * tells us whether we can probe for the type of port.
- */
- ret = serial8250_request_std_resource(up);
- if (ret < 0)
- return;
-
- if (port->iotype != up->cur_iotype)
- set_io_from_upio(port);
-
- if (flags & UART_CONFIG_TYPE)
- autoconfig(up);
-
- /* if access method is AU, it is a 16550 with a quirk */
- if (port->type == PORT_16550A && port->iotype == UPIO_AU)
- up->bugs |= UART_BUG_NOMSR;
-
- /* HW bugs may trigger IRQ while IIR == NO_INT */
- if (port->type == PORT_TEGRA)
- up->bugs |= UART_BUG_NOMSR;
-
- if (port->type != PORT_UNKNOWN && flags & UART_CONFIG_IRQ)
- autoconfig_irq(up);
-
- if (port->type == PORT_UNKNOWN)
- serial8250_release_std_resource(up);
-
- /* Fixme: probably not the best place for this */
- if ((port->type == PORT_XR17V35X) ||
- (port->type == PORT_XR17D15X))
- port->handle_irq = exar_handle_irq;
-
- register_dev_spec_attr_grp(up);
- up->fcr = uart_config[up->port.type].fcr;
-}
-
-static int
-serial8250_verify_port(struct uart_port *port, struct serial_struct *ser)
-{
- if (ser->irq >= nr_irqs || ser->irq < 0 ||
- ser->baud_base < 9600 || ser->type < PORT_UNKNOWN ||
- ser->type >= ARRAY_SIZE(uart_config) || ser->type == PORT_CIRRUS ||
- ser->type == PORT_STARTECH)
- return -EINVAL;
- return 0;
-}
-
-static const char *
-serial8250_type(struct uart_port *port)
-{
- int type = port->type;
-
- if (type >= ARRAY_SIZE(uart_config))
- type = 0;
- return uart_config[type].name;
-}
-
-static const struct uart_ops serial8250_pops = {
- .tx_empty = serial8250_tx_empty,
- .set_mctrl = serial8250_set_mctrl,
- .get_mctrl = serial8250_get_mctrl,
- .stop_tx = serial8250_stop_tx,
- .start_tx = serial8250_start_tx,
- .throttle = serial8250_throttle,
- .unthrottle = serial8250_unthrottle,
- .stop_rx = serial8250_stop_rx,
- .enable_ms = serial8250_enable_ms,
- .break_ctl = serial8250_break_ctl,
- .startup = serial8250_startup,
- .shutdown = serial8250_shutdown,
- .set_termios = serial8250_set_termios,
- .set_ldisc = serial8250_set_ldisc,
- .pm = serial8250_pm,
- .type = serial8250_type,
- .release_port = serial8250_release_port,
- .request_port = serial8250_request_port,
- .config_port = serial8250_config_port,
- .verify_port = serial8250_verify_port,
-#ifdef CONFIG_CONSOLE_POLL
- .poll_get_char = serial8250_get_poll_char,
- .poll_put_char = serial8250_put_poll_char,
-#endif
-};
-
static const struct uart_ops *base_ops;
static struct uart_ops univ8250_port_ops;
@@ -3139,42 +434,6 @@
}
EXPORT_SYMBOL(serial8250_set_isa_configurator);
-static void serial8250_init_port(struct uart_8250_port *up)
-{
- struct uart_port *port = &up->port;
-
- spin_lock_init(&port->lock);
- port->ops = &serial8250_pops;
-
- up->cur_iotype = 0xFF;
-}
-
-static void serial8250_set_defaults(struct uart_8250_port *up)
-{
- struct uart_port *port = &up->port;
-
- if (up->port.flags & UPF_FIXED_TYPE) {
- unsigned int type = up->port.type;
-
- if (!up->port.fifosize)
- up->port.fifosize = uart_config[type].fifo_size;
- if (!up->tx_loadsz)
- up->tx_loadsz = uart_config[type].tx_loadsz;
- if (!up->capabilities)
- up->capabilities = uart_config[type].flags;
- }
-
- set_io_from_upio(port);
-
- /* default dma handlers */
- if (up->dma) {
- if (!up->dma->tx_dma)
- up->dma->tx_dma = serial8250_tx_dma;
- if (!up->dma->rx_dma)
- up->dma->rx_dma = serial8250_rx_dma;
- }
-}
-
#ifdef CONFIG_SERIAL_8250_RSA
static void univ8250_config_port(struct uart_port *port, int flags)
@@ -3324,94 +583,6 @@
#ifdef CONFIG_SERIAL_8250_CONSOLE
-static void serial8250_console_putchar(struct uart_port *port, int ch)
-{
- struct uart_8250_port *up = up_to_u8250p(port);
-
- wait_for_xmitr(up, UART_LSR_THRE);
- serial_port_out(port, UART_TX, ch);
-}
-
-/*
- * Print a string to the serial port trying not to disturb
- * any possible real use of the port...
- *
- * The console_lock must be held when we get here.
- */
-static void serial8250_console_write(struct uart_8250_port *up, const char *s,
- unsigned int count)
-{
- struct uart_port *port = &up->port;
- unsigned long flags;
- unsigned int ier;
- int locked = 1;
-
- touch_nmi_watchdog();
-
- serial8250_rpm_get(up);
-
- if (port->sysrq)
- locked = 0;
- else if (oops_in_progress)
- locked = spin_trylock_irqsave(&port->lock, flags);
- else
- spin_lock_irqsave(&port->lock, flags);
-
- /*
- * First save the IER then disable the interrupts
- */
- ier = serial_port_in(port, UART_IER);
-
- if (up->capabilities & UART_CAP_UUE)
- serial_port_out(port, UART_IER, UART_IER_UUE);
- else
- serial_port_out(port, UART_IER, 0);
-
- /* check scratch reg to see if port powered off during system sleep */
- if (up->canary && (up->canary != serial_port_in(port, UART_SCR))) {
- struct ktermios termios;
- unsigned int baud, quot, frac = 0;
-
- termios.c_cflag = port->cons->cflag;
- if (port->state->port.tty && termios.c_cflag == 0)
- termios.c_cflag = port->state->port.tty->termios.c_cflag;
-
- baud = uart_get_baud_rate(port, &termios, NULL,
- port->uartclk / 16 / 0xffff,
- port->uartclk / 16);
- quot = serial8250_get_divisor(up, baud, &frac);
-
- serial8250_set_divisor(port, baud, quot, frac);
- serial_port_out(port, UART_LCR, up->lcr);
- serial_port_out(port, UART_MCR, UART_MCR_DTR | UART_MCR_RTS);
-
- up->canary = 0;
- }
-
- uart_console_write(port, s, count, serial8250_console_putchar);
-
- /*
- * Finally, wait for transmitter to become empty
- * and restore the IER
- */
- wait_for_xmitr(up, BOTH_EMPTY);
- serial_port_out(port, UART_IER, ier);
-
- /*
- * The receive handling will happen properly because the
- * receive ready bit will still be set; it is not cleared
- * on read. However, modem control will not, we must
- * call it if we have saved something in the saved flags
- * while processing with interrupts off.
- */
- if (up->msr_saved_flags)
- serial8250_modem_status(up);
-
- if (locked)
- spin_unlock_irqrestore(&port->lock, flags);
- serial8250_rpm_put(up);
-}
-
static void univ8250_console_write(struct console *co, const char *s,
unsigned int count)
{
@@ -3420,39 +591,6 @@
serial8250_console_write(up, s, count);
}
-static unsigned int probe_baud(struct uart_port *port)
-{
- unsigned char lcr, dll, dlm;
- unsigned int quot;
-
- lcr = serial_port_in(port, UART_LCR);
- serial_port_out(port, UART_LCR, lcr | UART_LCR_DLAB);
- dll = serial_port_in(port, UART_DLL);
- dlm = serial_port_in(port, UART_DLM);
- serial_port_out(port, UART_LCR, lcr);
-
- quot = (dlm << 8) | dll;
- return (port->uartclk / 16) / quot;
-}
-
-static int serial8250_console_setup(struct uart_port *port, char *options, bool probe)
-{
- int baud = 9600;
- int bits = 8;
- int parity = 'n';
- int flow = 'n';
-
- if (!port->iobase && !port->membase)
- return -ENODEV;
-
- if (options)
- uart_parse_options(options, &baud, &parity, &bits, &flow);
- else if (probe)
- baud = probe_baud(port);
-
- return uart_set_options(port, port->cons, baud, parity, bits, flow);
-}
-
static int univ8250_console_setup(struct console *co, char *options)
{
struct uart_port *port;
diff --git a/drivers/tty/serial/8250/8250_port.c b/drivers/tty/serial/8250/8250_port.c
new file mode 100644
index 0000000..4dc143e
--- /dev/null
+++ b/drivers/tty/serial/8250/8250_port.c
@@ -0,0 +1,2898 @@
+/*
+ * Base port operations for 8250/16550-type serial ports
+ *
+ * Based on drivers/char/serial.c, by Linus Torvalds, Theodore Ts'o.
+ * Split from 8250_core.c, Copyright (C) 2001 Russell King.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * A note about mapbase / membase
+ *
+ * mapbase is the physical address of the IO port.
+ * membase is an 'ioremapped' cookie.
+ */
+
+#if defined(CONFIG_SERIAL_8250_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
+#define SUPPORT_SYSRQ
+#endif
+
+#include <linux/module.h>
+#include <linux/moduleparam.h>
+#include <linux/ioport.h>
+#include <linux/init.h>
+#include <linux/console.h>
+#include <linux/sysrq.h>
+#include <linux/delay.h>
+#include <linux/platform_device.h>
+#include <linux/tty.h>
+#include <linux/ratelimit.h>
+#include <linux/tty_flip.h>
+#include <linux/serial.h>
+#include <linux/serial_8250.h>
+#include <linux/nmi.h>
+#include <linux/mutex.h>
+#include <linux/slab.h>
+#include <linux/uaccess.h>
+#include <linux/pm_runtime.h>
+
+#include <asm/io.h>
+#include <asm/irq.h>
+
+#include "8250.h"
+
+/*
+ * Debugging.
+ */
+#if 0
+#define DEBUG_AUTOCONF(fmt...) printk(fmt)
+#else
+#define DEBUG_AUTOCONF(fmt...) do { } while (0)
+#endif
+
+#define BOTH_EMPTY (UART_LSR_TEMT | UART_LSR_THRE)
+
+/*
+ * Here we define the default xmit fifo size used for each type of UART.
+ */
+static const struct serial8250_config uart_config[] = {
+ [PORT_UNKNOWN] = {
+ .name = "unknown",
+ .fifo_size = 1,
+ .tx_loadsz = 1,
+ },
+ [PORT_8250] = {
+ .name = "8250",
+ .fifo_size = 1,
+ .tx_loadsz = 1,
+ },
+ [PORT_16450] = {
+ .name = "16450",
+ .fifo_size = 1,
+ .tx_loadsz = 1,
+ },
+ [PORT_16550] = {
+ .name = "16550",
+ .fifo_size = 1,
+ .tx_loadsz = 1,
+ },
+ [PORT_16550A] = {
+ .name = "16550A",
+ .fifo_size = 16,
+ .tx_loadsz = 16,
+ .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10,
+ .rxtrig_bytes = {1, 4, 8, 14},
+ .flags = UART_CAP_FIFO,
+ },
+ [PORT_CIRRUS] = {
+ .name = "Cirrus",
+ .fifo_size = 1,
+ .tx_loadsz = 1,
+ },
+ [PORT_16650] = {
+ .name = "ST16650",
+ .fifo_size = 1,
+ .tx_loadsz = 1,
+ .flags = UART_CAP_FIFO | UART_CAP_EFR | UART_CAP_SLEEP,
+ },
+ [PORT_16650V2] = {
+ .name = "ST16650V2",
+ .fifo_size = 32,
+ .tx_loadsz = 16,
+ .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_01 |
+ UART_FCR_T_TRIG_00,
+ .rxtrig_bytes = {8, 16, 24, 28},
+ .flags = UART_CAP_FIFO | UART_CAP_EFR | UART_CAP_SLEEP,
+ },
+ [PORT_16750] = {
+ .name = "TI16750",
+ .fifo_size = 64,
+ .tx_loadsz = 64,
+ .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10 |
+ UART_FCR7_64BYTE,
+ .rxtrig_bytes = {1, 16, 32, 56},
+ .flags = UART_CAP_FIFO | UART_CAP_SLEEP | UART_CAP_AFE,
+ },
+ [PORT_STARTECH] = {
+ .name = "Startech",
+ .fifo_size = 1,
+ .tx_loadsz = 1,
+ },
+ [PORT_16C950] = {
+ .name = "16C950/954",
+ .fifo_size = 128,
+ .tx_loadsz = 128,
+ .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10,
+ /* UART_CAP_EFR breaks billionon CF bluetooth card. */
+ .flags = UART_CAP_FIFO | UART_CAP_SLEEP,
+ },
+ [PORT_16654] = {
+ .name = "ST16654",
+ .fifo_size = 64,
+ .tx_loadsz = 32,
+ .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_01 |
+ UART_FCR_T_TRIG_10,
+ .rxtrig_bytes = {8, 16, 56, 60},
+ .flags = UART_CAP_FIFO | UART_CAP_EFR | UART_CAP_SLEEP,
+ },
+ [PORT_16850] = {
+ .name = "XR16850",
+ .fifo_size = 128,
+ .tx_loadsz = 128,
+ .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10,
+ .flags = UART_CAP_FIFO | UART_CAP_EFR | UART_CAP_SLEEP,
+ },
+ [PORT_RSA] = {
+ .name = "RSA",
+ .fifo_size = 2048,
+ .tx_loadsz = 2048,
+ .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_11,
+ .flags = UART_CAP_FIFO,
+ },
+ [PORT_NS16550A] = {
+ .name = "NS16550A",
+ .fifo_size = 16,
+ .tx_loadsz = 16,
+ .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10,
+ .flags = UART_CAP_FIFO | UART_NATSEMI,
+ },
+ [PORT_XSCALE] = {
+ .name = "XScale",
+ .fifo_size = 32,
+ .tx_loadsz = 32,
+ .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10,
+ .flags = UART_CAP_FIFO | UART_CAP_UUE | UART_CAP_RTOIE,
+ },
+ [PORT_OCTEON] = {
+ .name = "OCTEON",
+ .fifo_size = 64,
+ .tx_loadsz = 64,
+ .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10,
+ .flags = UART_CAP_FIFO,
+ },
+ [PORT_AR7] = {
+ .name = "AR7",
+ .fifo_size = 16,
+ .tx_loadsz = 16,
+ .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_00,
+ .flags = UART_CAP_FIFO | UART_CAP_AFE,
+ },
+ [PORT_U6_16550A] = {
+ .name = "U6_16550A",
+ .fifo_size = 64,
+ .tx_loadsz = 64,
+ .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10,
+ .flags = UART_CAP_FIFO | UART_CAP_AFE,
+ },
+ [PORT_TEGRA] = {
+ .name = "Tegra",
+ .fifo_size = 32,
+ .tx_loadsz = 8,
+ .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_01 |
+ UART_FCR_T_TRIG_01,
+ .rxtrig_bytes = {1, 4, 8, 14},
+ .flags = UART_CAP_FIFO | UART_CAP_RTOIE,
+ },
+ [PORT_XR17D15X] = {
+ .name = "XR17D15X",
+ .fifo_size = 64,
+ .tx_loadsz = 64,
+ .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10,
+ .flags = UART_CAP_FIFO | UART_CAP_AFE | UART_CAP_EFR |
+ UART_CAP_SLEEP,
+ },
+ [PORT_XR17V35X] = {
+ .name = "XR17V35X",
+ .fifo_size = 256,
+ .tx_loadsz = 256,
+ .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_11 |
+ UART_FCR_T_TRIG_11,
+ .flags = UART_CAP_FIFO | UART_CAP_AFE | UART_CAP_EFR |
+ UART_CAP_SLEEP,
+ },
+ [PORT_LPC3220] = {
+ .name = "LPC3220",
+ .fifo_size = 64,
+ .tx_loadsz = 32,
+ .fcr = UART_FCR_DMA_SELECT | UART_FCR_ENABLE_FIFO |
+ UART_FCR_R_TRIG_00 | UART_FCR_T_TRIG_00,
+ .flags = UART_CAP_FIFO,
+ },
+ [PORT_BRCM_TRUMANAGE] = {
+ .name = "TruManage",
+ .fifo_size = 1,
+ .tx_loadsz = 1024,
+ .flags = UART_CAP_HFIFO,
+ },
+ [PORT_8250_CIR] = {
+ .name = "CIR port"
+ },
+ [PORT_ALTR_16550_F32] = {
+ .name = "Altera 16550 FIFO32",
+ .fifo_size = 32,
+ .tx_loadsz = 32,
+ .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10,
+ .flags = UART_CAP_FIFO | UART_CAP_AFE,
+ },
+ [PORT_ALTR_16550_F64] = {
+ .name = "Altera 16550 FIFO64",
+ .fifo_size = 64,
+ .tx_loadsz = 64,
+ .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10,
+ .flags = UART_CAP_FIFO | UART_CAP_AFE,
+ },
+ [PORT_ALTR_16550_F128] = {
+ .name = "Altera 16550 FIFO128",
+ .fifo_size = 128,
+ .tx_loadsz = 128,
+ .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10,
+ .flags = UART_CAP_FIFO | UART_CAP_AFE,
+ },
+/* tx_loadsz is set to 63-bytes instead of 64-bytes to implement
+workaround of errata A-008006 which states that tx_loadsz should be
+configured less than Maximum supported fifo bytes */
+ [PORT_16550A_FSL64] = {
+ .name = "16550A_FSL64",
+ .fifo_size = 64,
+ .tx_loadsz = 63,
+ .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10 |
+ UART_FCR7_64BYTE,
+ .flags = UART_CAP_FIFO,
+ },
+};
+
+/* Uart divisor latch read */
+static int default_serial_dl_read(struct uart_8250_port *up)
+{
+ return serial_in(up, UART_DLL) | serial_in(up, UART_DLM) << 8;
+}
+
+/* Uart divisor latch write */
+static void default_serial_dl_write(struct uart_8250_port *up, int value)
+{
+ serial_out(up, UART_DLL, value & 0xff);
+ serial_out(up, UART_DLM, value >> 8 & 0xff);
+}
+
+#if defined(CONFIG_MIPS_ALCHEMY) || defined(CONFIG_SERIAL_8250_RT288X)
+
+/* Au1x00/RT288x UART hardware has a weird register layout */
+static const s8 au_io_in_map[8] = {
+ 0, /* UART_RX */
+ 2, /* UART_IER */
+ 3, /* UART_IIR */
+ 5, /* UART_LCR */
+ 6, /* UART_MCR */
+ 7, /* UART_LSR */
+ 8, /* UART_MSR */
+ -1, /* UART_SCR (unmapped) */
+};
+
+static const s8 au_io_out_map[8] = {
+ 1, /* UART_TX */
+ 2, /* UART_IER */
+ 4, /* UART_FCR */
+ 5, /* UART_LCR */
+ 6, /* UART_MCR */
+ -1, /* UART_LSR (unmapped) */
+ -1, /* UART_MSR (unmapped) */
+ -1, /* UART_SCR (unmapped) */
+};
+
+static unsigned int au_serial_in(struct uart_port *p, int offset)
+{
+ if (offset >= ARRAY_SIZE(au_io_in_map))
+ return UINT_MAX;
+ offset = au_io_in_map[offset];
+ if (offset < 0)
+ return UINT_MAX;
+ return __raw_readl(p->membase + (offset << p->regshift));
+}
+
+static void au_serial_out(struct uart_port *p, int offset, int value)
+{
+ if (offset >= ARRAY_SIZE(au_io_out_map))
+ return;
+ offset = au_io_out_map[offset];
+ if (offset < 0)
+ return;
+ __raw_writel(value, p->membase + (offset << p->regshift));
+}
+
+/* Au1x00 haven't got a standard divisor latch */
+static int au_serial_dl_read(struct uart_8250_port *up)
+{
+ return __raw_readl(up->port.membase + 0x28);
+}
+
+static void au_serial_dl_write(struct uart_8250_port *up, int value)
+{
+ __raw_writel(value, up->port.membase + 0x28);
+}
+
+#endif
+
+static unsigned int hub6_serial_in(struct uart_port *p, int offset)
+{
+ offset = offset << p->regshift;
+ outb(p->hub6 - 1 + offset, p->iobase);
+ return inb(p->iobase + 1);
+}
+
+static void hub6_serial_out(struct uart_port *p, int offset, int value)
+{
+ offset = offset << p->regshift;
+ outb(p->hub6 - 1 + offset, p->iobase);
+ outb(value, p->iobase + 1);
+}
+
+static unsigned int mem_serial_in(struct uart_port *p, int offset)
+{
+ offset = offset << p->regshift;
+ return readb(p->membase + offset);
+}
+
+static void mem_serial_out(struct uart_port *p, int offset, int value)
+{
+ offset = offset << p->regshift;
+ writeb(value, p->membase + offset);
+}
+
+static void mem32_serial_out(struct uart_port *p, int offset, int value)
+{
+ offset = offset << p->regshift;
+ writel(value, p->membase + offset);
+}
+
+static unsigned int mem32_serial_in(struct uart_port *p, int offset)
+{
+ offset = offset << p->regshift;
+ return readl(p->membase + offset);
+}
+
+static void mem32be_serial_out(struct uart_port *p, int offset, int value)
+{
+ offset = offset << p->regshift;
+ iowrite32be(value, p->membase + offset);
+}
+
+static unsigned int mem32be_serial_in(struct uart_port *p, int offset)
+{
+ offset = offset << p->regshift;
+ return ioread32be(p->membase + offset);
+}
+
+static unsigned int io_serial_in(struct uart_port *p, int offset)
+{
+ offset = offset << p->regshift;
+ return inb(p->iobase + offset);
+}
+
+static void io_serial_out(struct uart_port *p, int offset, int value)
+{
+ offset = offset << p->regshift;
+ outb(value, p->iobase + offset);
+}
+
+static int serial8250_default_handle_irq(struct uart_port *port);
+static int exar_handle_irq(struct uart_port *port);
+
+static void set_io_from_upio(struct uart_port *p)
+{
+ struct uart_8250_port *up = up_to_u8250p(p);
+
+ up->dl_read = default_serial_dl_read;
+ up->dl_write = default_serial_dl_write;
+
+ switch (p->iotype) {
+ case UPIO_HUB6:
+ p->serial_in = hub6_serial_in;
+ p->serial_out = hub6_serial_out;
+ break;
+
+ case UPIO_MEM:
+ p->serial_in = mem_serial_in;
+ p->serial_out = mem_serial_out;
+ break;
+
+ case UPIO_MEM32:
+ p->serial_in = mem32_serial_in;
+ p->serial_out = mem32_serial_out;
+ break;
+
+ case UPIO_MEM32BE:
+ p->serial_in = mem32be_serial_in;
+ p->serial_out = mem32be_serial_out;
+ break;
+
+#if defined(CONFIG_MIPS_ALCHEMY) || defined(CONFIG_SERIAL_8250_RT288X)
+ case UPIO_AU:
+ p->serial_in = au_serial_in;
+ p->serial_out = au_serial_out;
+ up->dl_read = au_serial_dl_read;
+ up->dl_write = au_serial_dl_write;
+ break;
+#endif
+
+ default:
+ p->serial_in = io_serial_in;
+ p->serial_out = io_serial_out;
+ break;
+ }
+ /* Remember loaded iotype */
+ up->cur_iotype = p->iotype;
+ p->handle_irq = serial8250_default_handle_irq;
+}
+
+static void
+serial_port_out_sync(struct uart_port *p, int offset, int value)
+{
+ switch (p->iotype) {
+ case UPIO_MEM:
+ case UPIO_MEM32:
+ case UPIO_MEM32BE:
+ case UPIO_AU:
+ p->serial_out(p, offset, value);
+ p->serial_in(p, UART_LCR); /* safe, no side-effects */
+ break;
+ default:
+ p->serial_out(p, offset, value);
+ }
+}
+
+/*
+ * For the 16C950
+ */
+static void serial_icr_write(struct uart_8250_port *up, int offset, int value)
+{
+ serial_out(up, UART_SCR, offset);
+ serial_out(up, UART_ICR, value);
+}
+
+static unsigned int serial_icr_read(struct uart_8250_port *up, int offset)
+{
+ unsigned int value;
+
+ serial_icr_write(up, UART_ACR, up->acr | UART_ACR_ICRRD);
+ serial_out(up, UART_SCR, offset);
+ value = serial_in(up, UART_ICR);
+ serial_icr_write(up, UART_ACR, up->acr);
+
+ return value;
+}
+
+/*
+ * FIFO support.
+ */
+static void serial8250_clear_fifos(struct uart_8250_port *p)
+{
+ if (p->capabilities & UART_CAP_FIFO) {
+ serial_out(p, UART_FCR, UART_FCR_ENABLE_FIFO);
+ serial_out(p, UART_FCR, UART_FCR_ENABLE_FIFO |
+ UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT);
+ serial_out(p, UART_FCR, 0);
+ }
+}
+
+void serial8250_clear_and_reinit_fifos(struct uart_8250_port *p)
+{
+ serial8250_clear_fifos(p);
+ serial_out(p, UART_FCR, p->fcr);
+}
+EXPORT_SYMBOL_GPL(serial8250_clear_and_reinit_fifos);
+
+void serial8250_rpm_get(struct uart_8250_port *p)
+{
+ if (!(p->capabilities & UART_CAP_RPM))
+ return;
+ pm_runtime_get_sync(p->port.dev);
+}
+EXPORT_SYMBOL_GPL(serial8250_rpm_get);
+
+void serial8250_rpm_put(struct uart_8250_port *p)
+{
+ if (!(p->capabilities & UART_CAP_RPM))
+ return;
+ pm_runtime_mark_last_busy(p->port.dev);
+ pm_runtime_put_autosuspend(p->port.dev);
+}
+EXPORT_SYMBOL_GPL(serial8250_rpm_put);
+
+/*
+ * These two wrappers ensure that enable_runtime_pm_tx() can be called more than
+ * once and disable_runtime_pm_tx() will still disable RPM because the fifo is
+ * empty and the HW can idle again.
+ */
+static void serial8250_rpm_get_tx(struct uart_8250_port *p)
+{
+ unsigned char rpm_active;
+
+ if (!(p->capabilities & UART_CAP_RPM))
+ return;
+
+ rpm_active = xchg(&p->rpm_tx_active, 1);
+ if (rpm_active)
+ return;
+ pm_runtime_get_sync(p->port.dev);
+}
+
+static void serial8250_rpm_put_tx(struct uart_8250_port *p)
+{
+ unsigned char rpm_active;
+
+ if (!(p->capabilities & UART_CAP_RPM))
+ return;
+
+ rpm_active = xchg(&p->rpm_tx_active, 0);
+ if (!rpm_active)
+ return;
+ pm_runtime_mark_last_busy(p->port.dev);
+ pm_runtime_put_autosuspend(p->port.dev);
+}
+
+/*
+ * IER sleep support. UARTs which have EFRs need the "extended
+ * capability" bit enabled. Note that on XR16C850s, we need to
+ * reset LCR to write to IER.
+ */
+static void serial8250_set_sleep(struct uart_8250_port *p, int sleep)
+{
+ unsigned char lcr = 0, efr = 0;
+ /*
+ * Exar UARTs have a SLEEP register that enables or disables
+ * each UART to enter sleep mode separately. On the XR17V35x the
+ * register is accessible to each UART at the UART_EXAR_SLEEP
+ * offset but the UART channel may only write to the corresponding
+ * bit.
+ */
+ serial8250_rpm_get(p);
+ if ((p->port.type == PORT_XR17V35X) ||
+ (p->port.type == PORT_XR17D15X)) {
+ serial_out(p, UART_EXAR_SLEEP, sleep ? 0xff : 0);
+ goto out;
+ }
+
+ if (p->capabilities & UART_CAP_SLEEP) {
+ if (p->capabilities & UART_CAP_EFR) {
+ lcr = serial_in(p, UART_LCR);
+ efr = serial_in(p, UART_EFR);
+ serial_out(p, UART_LCR, UART_LCR_CONF_MODE_B);
+ serial_out(p, UART_EFR, UART_EFR_ECB);
+ serial_out(p, UART_LCR, 0);
+ }
+ serial_out(p, UART_IER, sleep ? UART_IERX_SLEEP : 0);
+ if (p->capabilities & UART_CAP_EFR) {
+ serial_out(p, UART_LCR, UART_LCR_CONF_MODE_B);
+ serial_out(p, UART_EFR, efr);
+ serial_out(p, UART_LCR, lcr);
+ }
+ }
+out:
+ serial8250_rpm_put(p);
+}
+
+#ifdef CONFIG_SERIAL_8250_RSA
+/*
+ * Attempts to turn on the RSA FIFO. Returns zero on failure.
+ * We set the port uart clock rate if we succeed.
+ */
+static int __enable_rsa(struct uart_8250_port *up)
+{
+ unsigned char mode;
+ int result;
+
+ mode = serial_in(up, UART_RSA_MSR);
+ result = mode & UART_RSA_MSR_FIFO;
+
+ if (!result) {
+ serial_out(up, UART_RSA_MSR, mode | UART_RSA_MSR_FIFO);
+ mode = serial_in(up, UART_RSA_MSR);
+ result = mode & UART_RSA_MSR_FIFO;
+ }
+
+ if (result)
+ up->port.uartclk = SERIAL_RSA_BAUD_BASE * 16;
+
+ return result;
+}
+
+static void enable_rsa(struct uart_8250_port *up)
+{
+ if (up->port.type == PORT_RSA) {
+ if (up->port.uartclk != SERIAL_RSA_BAUD_BASE * 16) {
+ spin_lock_irq(&up->port.lock);
+ __enable_rsa(up);
+ spin_unlock_irq(&up->port.lock);
+ }
+ if (up->port.uartclk == SERIAL_RSA_BAUD_BASE * 16)
+ serial_out(up, UART_RSA_FRR, 0);
+ }
+}
+
+/*
+ * Attempts to turn off the RSA FIFO. Returns zero on failure.
+ * It is unknown why interrupts were disabled in here. However,
+ * the caller is expected to preserve this behaviour by grabbing
+ * the spinlock before calling this function.
+ */
+static void disable_rsa(struct uart_8250_port *up)
+{
+ unsigned char mode;
+ int result;
+
+ if (up->port.type == PORT_RSA &&
+ up->port.uartclk == SERIAL_RSA_BAUD_BASE * 16) {
+ spin_lock_irq(&up->port.lock);
+
+ mode = serial_in(up, UART_RSA_MSR);
+ result = !(mode & UART_RSA_MSR_FIFO);
+
+ if (!result) {
+ serial_out(up, UART_RSA_MSR, mode & ~UART_RSA_MSR_FIFO);
+ mode = serial_in(up, UART_RSA_MSR);
+ result = !(mode & UART_RSA_MSR_FIFO);
+ }
+
+ if (result)
+ up->port.uartclk = SERIAL_RSA_BAUD_BASE_LO * 16;
+ spin_unlock_irq(&up->port.lock);
+ }
+}
+#endif /* CONFIG_SERIAL_8250_RSA */
+
+/*
+ * This is a quickie test to see how big the FIFO is.
+ * It doesn't work at all the time, more's the pity.
+ */
+static int size_fifo(struct uart_8250_port *up)
+{
+ unsigned char old_fcr, old_mcr, old_lcr;
+ unsigned short old_dl;
+ int count;
+
+ old_lcr = serial_in(up, UART_LCR);
+ serial_out(up, UART_LCR, 0);
+ old_fcr = serial_in(up, UART_FCR);
+ old_mcr = serial_in(up, UART_MCR);
+ serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO |
+ UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT);
+ serial_out(up, UART_MCR, UART_MCR_LOOP);
+ serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A);
+ old_dl = serial_dl_read(up);
+ serial_dl_write(up, 0x0001);
+ serial_out(up, UART_LCR, 0x03);
+ for (count = 0; count < 256; count++)
+ serial_out(up, UART_TX, count);
+ mdelay(20);/* FIXME - schedule_timeout */
+ for (count = 0; (serial_in(up, UART_LSR) & UART_LSR_DR) &&
+ (count < 256); count++)
+ serial_in(up, UART_RX);
+ serial_out(up, UART_FCR, old_fcr);
+ serial_out(up, UART_MCR, old_mcr);
+ serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A);
+ serial_dl_write(up, old_dl);
+ serial_out(up, UART_LCR, old_lcr);
+
+ return count;
+}
+
+/*
+ * Read UART ID using the divisor method - set DLL and DLM to zero
+ * and the revision will be in DLL and device type in DLM. We
+ * preserve the device state across this.
+ */
+static unsigned int autoconfig_read_divisor_id(struct uart_8250_port *p)
+{
+ unsigned char old_dll, old_dlm, old_lcr;
+ unsigned int id;
+
+ old_lcr = serial_in(p, UART_LCR);
+ serial_out(p, UART_LCR, UART_LCR_CONF_MODE_A);
+
+ old_dll = serial_in(p, UART_DLL);
+ old_dlm = serial_in(p, UART_DLM);
+
+ serial_out(p, UART_DLL, 0);
+ serial_out(p, UART_DLM, 0);
+
+ id = serial_in(p, UART_DLL) | serial_in(p, UART_DLM) << 8;
+
+ serial_out(p, UART_DLL, old_dll);
+ serial_out(p, UART_DLM, old_dlm);
+ serial_out(p, UART_LCR, old_lcr);
+
+ return id;
+}
+
+/*
+ * This is a helper routine to autodetect StarTech/Exar/Oxsemi UART's.
+ * When this function is called we know it is at least a StarTech
+ * 16650 V2, but it might be one of several StarTech UARTs, or one of
+ * its clones. (We treat the broken original StarTech 16650 V1 as a
+ * 16550, and why not? Startech doesn't seem to even acknowledge its
+ * existence.)
+ *
+ * What evil have men's minds wrought...
+ */
+static void autoconfig_has_efr(struct uart_8250_port *up)
+{
+ unsigned int id1, id2, id3, rev;
+
+ /*
+ * Everything with an EFR has SLEEP
+ */
+ up->capabilities |= UART_CAP_EFR | UART_CAP_SLEEP;
+
+ /*
+ * First we check to see if it's an Oxford Semiconductor UART.
+ *
+ * If we have to do this here because some non-National
+ * Semiconductor clone chips lock up if you try writing to the
+ * LSR register (which serial_icr_read does)
+ */
+
+ /*
+ * Check for Oxford Semiconductor 16C950.
+ *
+ * EFR [4] must be set else this test fails.
+ *
+ * This shouldn't be necessary, but Mike Hudson (Exoray@isys.ca)
+ * claims that it's needed for 952 dual UART's (which are not
+ * recommended for new designs).
+ */
+ up->acr = 0;
+ serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
+ serial_out(up, UART_EFR, UART_EFR_ECB);
+ serial_out(up, UART_LCR, 0x00);
+ id1 = serial_icr_read(up, UART_ID1);
+ id2 = serial_icr_read(up, UART_ID2);
+ id3 = serial_icr_read(up, UART_ID3);
+ rev = serial_icr_read(up, UART_REV);
+
+ DEBUG_AUTOCONF("950id=%02x:%02x:%02x:%02x ", id1, id2, id3, rev);
+
+ if (id1 == 0x16 && id2 == 0xC9 &&
+ (id3 == 0x50 || id3 == 0x52 || id3 == 0x54)) {
+ up->port.type = PORT_16C950;
+
+ /*
+ * Enable work around for the Oxford Semiconductor 952 rev B
+ * chip which causes it to seriously miscalculate baud rates
+ * when DLL is 0.
+ */
+ if (id3 == 0x52 && rev == 0x01)
+ up->bugs |= UART_BUG_QUOT;
+ return;
+ }
+
+ /*
+ * We check for a XR16C850 by setting DLL and DLM to 0, and then
+ * reading back DLL and DLM. The chip type depends on the DLM
+ * value read back:
+ * 0x10 - XR16C850 and the DLL contains the chip revision.
+ * 0x12 - XR16C2850.
+ * 0x14 - XR16C854.
+ */
+ id1 = autoconfig_read_divisor_id(up);
+ DEBUG_AUTOCONF("850id=%04x ", id1);
+
+ id2 = id1 >> 8;
+ if (id2 == 0x10 || id2 == 0x12 || id2 == 0x14) {
+ up->port.type = PORT_16850;
+ return;
+ }
+
+ /*
+ * It wasn't an XR16C850.
+ *
+ * We distinguish between the '654 and the '650 by counting
+ * how many bytes are in the FIFO. I'm using this for now,
+ * since that's the technique that was sent to me in the
+ * serial driver update, but I'm not convinced this works.
+ * I've had problems doing this in the past. -TYT
+ */
+ if (size_fifo(up) == 64)
+ up->port.type = PORT_16654;
+ else
+ up->port.type = PORT_16650V2;
+}
+
+/*
+ * We detected a chip without a FIFO. Only two fall into
+ * this category - the original 8250 and the 16450. The
+ * 16450 has a scratch register (accessible with LCR=0)
+ */
+static void autoconfig_8250(struct uart_8250_port *up)
+{
+ unsigned char scratch, status1, status2;
+
+ up->port.type = PORT_8250;
+
+ scratch = serial_in(up, UART_SCR);
+ serial_out(up, UART_SCR, 0xa5);
+ status1 = serial_in(up, UART_SCR);
+ serial_out(up, UART_SCR, 0x5a);
+ status2 = serial_in(up, UART_SCR);
+ serial_out(up, UART_SCR, scratch);
+
+ if (status1 == 0xa5 && status2 == 0x5a)
+ up->port.type = PORT_16450;
+}
+
+static int broken_efr(struct uart_8250_port *up)
+{
+ /*
+ * Exar ST16C2550 "A2" devices incorrectly detect as
+ * having an EFR, and report an ID of 0x0201. See
+ * http://linux.derkeiler.com/Mailing-Lists/Kernel/2004-11/4812.html
+ */
+ if (autoconfig_read_divisor_id(up) == 0x0201 && size_fifo(up) == 16)
+ return 1;
+
+ return 0;
+}
+
+/*
+ * We know that the chip has FIFOs. Does it have an EFR? The
+ * EFR is located in the same register position as the IIR and
+ * we know the top two bits of the IIR are currently set. The
+ * EFR should contain zero. Try to read the EFR.
+ */
+static void autoconfig_16550a(struct uart_8250_port *up)
+{
+ unsigned char status1, status2;
+ unsigned int iersave;
+
+ up->port.type = PORT_16550A;
+ up->capabilities |= UART_CAP_FIFO;
+
+ /*
+ * XR17V35x UARTs have an extra divisor register, DLD
+ * that gets enabled with when DLAB is set which will
+ * cause the device to incorrectly match and assign
+ * port type to PORT_16650. The EFR for this UART is
+ * found at offset 0x09. Instead check the Deice ID (DVID)
+ * register for a 2, 4 or 8 port UART.
+ */
+ if (up->port.flags & UPF_EXAR_EFR) {
+ status1 = serial_in(up, UART_EXAR_DVID);
+ if (status1 == 0x82 || status1 == 0x84 || status1 == 0x88) {
+ DEBUG_AUTOCONF("Exar XR17V35x ");
+ up->port.type = PORT_XR17V35X;
+ up->capabilities |= UART_CAP_AFE | UART_CAP_EFR |
+ UART_CAP_SLEEP;
+
+ return;
+ }
+
+ }
+
+ /*
+ * Check for presence of the EFR when DLAB is set.
+ * Only ST16C650V1 UARTs pass this test.
+ */
+ serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A);
+ if (serial_in(up, UART_EFR) == 0) {
+ serial_out(up, UART_EFR, 0xA8);
+ if (serial_in(up, UART_EFR) != 0) {
+ DEBUG_AUTOCONF("EFRv1 ");
+ up->port.type = PORT_16650;
+ up->capabilities |= UART_CAP_EFR | UART_CAP_SLEEP;
+ } else {
+ serial_out(up, UART_LCR, 0);
+ serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO |
+ UART_FCR7_64BYTE);
+ status1 = serial_in(up, UART_IIR) >> 5;
+ serial_out(up, UART_FCR, 0);
+ serial_out(up, UART_LCR, 0);
+
+ if (status1 == 7)
+ up->port.type = PORT_16550A_FSL64;
+ else
+ DEBUG_AUTOCONF("Motorola 8xxx DUART ");
+ }
+ serial_out(up, UART_EFR, 0);
+ return;
+ }
+
+ /*
+ * Maybe it requires 0xbf to be written to the LCR.
+ * (other ST16C650V2 UARTs, TI16C752A, etc)
+ */
+ serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
+ if (serial_in(up, UART_EFR) == 0 && !broken_efr(up)) {
+ DEBUG_AUTOCONF("EFRv2 ");
+ autoconfig_has_efr(up);
+ return;
+ }
+
+ /*
+ * Check for a National Semiconductor SuperIO chip.
+ * Attempt to switch to bank 2, read the value of the LOOP bit
+ * from EXCR1. Switch back to bank 0, change it in MCR. Then
+ * switch back to bank 2, read it from EXCR1 again and check
+ * it's changed. If so, set baud_base in EXCR2 to 921600. -- dwmw2
+ */
+ serial_out(up, UART_LCR, 0);
+ status1 = serial_in(up, UART_MCR);
+ serial_out(up, UART_LCR, 0xE0);
+ status2 = serial_in(up, 0x02); /* EXCR1 */
+
+ if (!((status2 ^ status1) & UART_MCR_LOOP)) {
+ serial_out(up, UART_LCR, 0);
+ serial_out(up, UART_MCR, status1 ^ UART_MCR_LOOP);
+ serial_out(up, UART_LCR, 0xE0);
+ status2 = serial_in(up, 0x02); /* EXCR1 */
+ serial_out(up, UART_LCR, 0);
+ serial_out(up, UART_MCR, status1);
+
+ if ((status2 ^ status1) & UART_MCR_LOOP) {
+ unsigned short quot;
+
+ serial_out(up, UART_LCR, 0xE0);
+
+ quot = serial_dl_read(up);
+ quot <<= 3;
+
+ if (ns16550a_goto_highspeed(up))
+ serial_dl_write(up, quot);
+
+ serial_out(up, UART_LCR, 0);
+
+ up->port.uartclk = 921600*16;
+ up->port.type = PORT_NS16550A;
+ up->capabilities |= UART_NATSEMI;
+ return;
+ }
+ }
+
+ /*
+ * No EFR. Try to detect a TI16750, which only sets bit 5 of
+ * the IIR when 64 byte FIFO mode is enabled when DLAB is set.
+ * Try setting it with and without DLAB set. Cheap clones
+ * set bit 5 without DLAB set.
+ */
+ serial_out(up, UART_LCR, 0);
+ serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO | UART_FCR7_64BYTE);
+ status1 = serial_in(up, UART_IIR) >> 5;
+ serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO);
+ serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A);
+ serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO | UART_FCR7_64BYTE);
+ status2 = serial_in(up, UART_IIR) >> 5;
+ serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO);
+ serial_out(up, UART_LCR, 0);
+
+ DEBUG_AUTOCONF("iir1=%d iir2=%d ", status1, status2);
+
+ if (status1 == 6 && status2 == 7) {
+ up->port.type = PORT_16750;
+ up->capabilities |= UART_CAP_AFE | UART_CAP_SLEEP;
+ return;
+ }
+
+ /*
+ * Try writing and reading the UART_IER_UUE bit (b6).
+ * If it works, this is probably one of the Xscale platform's
+ * internal UARTs.
+ * We're going to explicitly set the UUE bit to 0 before
+ * trying to write and read a 1 just to make sure it's not
+ * already a 1 and maybe locked there before we even start start.
+ */
+ iersave = serial_in(up, UART_IER);
+ serial_out(up, UART_IER, iersave & ~UART_IER_UUE);
+ if (!(serial_in(up, UART_IER) & UART_IER_UUE)) {
+ /*
+ * OK it's in a known zero state, try writing and reading
+ * without disturbing the current state of the other bits.
+ */
+ serial_out(up, UART_IER, iersave | UART_IER_UUE);
+ if (serial_in(up, UART_IER) & UART_IER_UUE) {
+ /*
+ * It's an Xscale.
+ * We'll leave the UART_IER_UUE bit set to 1 (enabled).
+ */
+ DEBUG_AUTOCONF("Xscale ");
+ up->port.type = PORT_XSCALE;
+ up->capabilities |= UART_CAP_UUE | UART_CAP_RTOIE;
+ return;
+ }
+ } else {
+ /*
+ * If we got here we couldn't force the IER_UUE bit to 0.
+ * Log it and continue.
+ */
+ DEBUG_AUTOCONF("Couldn't force IER_UUE to 0 ");
+ }
+ serial_out(up, UART_IER, iersave);
+
+ /*
+ * Exar uarts have EFR in a weird location
+ */
+ if (up->port.flags & UPF_EXAR_EFR) {
+ DEBUG_AUTOCONF("Exar XR17D15x ");
+ up->port.type = PORT_XR17D15X;
+ up->capabilities |= UART_CAP_AFE | UART_CAP_EFR |
+ UART_CAP_SLEEP;
+
+ return;
+ }
+
+ /*
+ * We distinguish between 16550A and U6 16550A by counting
+ * how many bytes are in the FIFO.
+ */
+ if (up->port.type == PORT_16550A && size_fifo(up) == 64) {
+ up->port.type = PORT_U6_16550A;
+ up->capabilities |= UART_CAP_AFE;
+ }
+}
+
+/*
+ * This routine is called by rs_init() to initialize a specific serial
+ * port. It determines what type of UART chip this serial port is
+ * using: 8250, 16450, 16550, 16550A. The important question is
+ * whether or not this UART is a 16550A or not, since this will
+ * determine whether or not we can use its FIFO features or not.
+ */
+static void autoconfig(struct uart_8250_port *up)
+{
+ unsigned char status1, scratch, scratch2, scratch3;
+ unsigned char save_lcr, save_mcr;
+ struct uart_port *port = &up->port;
+ unsigned long flags;
+ unsigned int old_capabilities;
+
+ if (!port->iobase && !port->mapbase && !port->membase)
+ return;
+
+ DEBUG_AUTOCONF("ttyS%d: autoconf (0x%04lx, 0x%p): ",
+ serial_index(port), port->iobase, port->membase);
+
+ /*
+ * We really do need global IRQs disabled here - we're going to
+ * be frobbing the chips IRQ enable register to see if it exists.
+ */
+ spin_lock_irqsave(&port->lock, flags);
+
+ up->capabilities = 0;
+ up->bugs = 0;
+
+ if (!(port->flags & UPF_BUGGY_UART)) {
+ /*
+ * Do a simple existence test first; if we fail this,
+ * there's no point trying anything else.
+ *
+ * 0x80 is used as a nonsense port to prevent against
+ * false positives due to ISA bus float. The
+ * assumption is that 0x80 is a non-existent port;
+ * which should be safe since include/asm/io.h also
+ * makes this assumption.
+ *
+ * Note: this is safe as long as MCR bit 4 is clear
+ * and the device is in "PC" mode.
+ */
+ scratch = serial_in(up, UART_IER);
+ serial_out(up, UART_IER, 0);
+#ifdef __i386__
+ outb(0xff, 0x080);
+#endif
+ /*
+ * Mask out IER[7:4] bits for test as some UARTs (e.g. TL
+ * 16C754B) allow only to modify them if an EFR bit is set.
+ */
+ scratch2 = serial_in(up, UART_IER) & 0x0f;
+ serial_out(up, UART_IER, 0x0F);
+#ifdef __i386__
+ outb(0, 0x080);
+#endif
+ scratch3 = serial_in(up, UART_IER) & 0x0f;
+ serial_out(up, UART_IER, scratch);
+ if (scratch2 != 0 || scratch3 != 0x0F) {
+ /*
+ * We failed; there's nothing here
+ */
+ spin_unlock_irqrestore(&port->lock, flags);
+ DEBUG_AUTOCONF("IER test failed (%02x, %02x) ",
+ scratch2, scratch3);
+ goto out;
+ }
+ }
+
+ save_mcr = serial_in(up, UART_MCR);
+ save_lcr = serial_in(up, UART_LCR);
+
+ /*
+ * Check to see if a UART is really there. Certain broken
+ * internal modems based on the Rockwell chipset fail this
+ * test, because they apparently don't implement the loopback
+ * test mode. So this test is skipped on the COM 1 through
+ * COM 4 ports. This *should* be safe, since no board
+ * manufacturer would be stupid enough to design a board
+ * that conflicts with COM 1-4 --- we hope!
+ */
+ if (!(port->flags & UPF_SKIP_TEST)) {
+ serial_out(up, UART_MCR, UART_MCR_LOOP | 0x0A);
+ status1 = serial_in(up, UART_MSR) & 0xF0;
+ serial_out(up, UART_MCR, save_mcr);
+ if (status1 != 0x90) {
+ spin_unlock_irqrestore(&port->lock, flags);
+ DEBUG_AUTOCONF("LOOP test failed (%02x) ",
+ status1);
+ goto out;
+ }
+ }
+
+ /*
+ * We're pretty sure there's a port here. Lets find out what
+ * type of port it is. The IIR top two bits allows us to find
+ * out if it's 8250 or 16450, 16550, 16550A or later. This
+ * determines what we test for next.
+ *
+ * We also initialise the EFR (if any) to zero for later. The
+ * EFR occupies the same register location as the FCR and IIR.
+ */
+ serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
+ serial_out(up, UART_EFR, 0);
+ serial_out(up, UART_LCR, 0);
+
+ serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO);
+ scratch = serial_in(up, UART_IIR) >> 6;
+
+ switch (scratch) {
+ case 0:
+ autoconfig_8250(up);
+ break;
+ case 1:
+ port->type = PORT_UNKNOWN;
+ break;
+ case 2:
+ port->type = PORT_16550;
+ break;
+ case 3:
+ autoconfig_16550a(up);
+ break;
+ }
+
+#ifdef CONFIG_SERIAL_8250_RSA
+ /*
+ * Only probe for RSA ports if we got the region.
+ */
+ if (port->type == PORT_16550A && up->probe & UART_PROBE_RSA &&
+ __enable_rsa(up))
+ port->type = PORT_RSA;
+#endif
+
+ serial_out(up, UART_LCR, save_lcr);
+
+ port->fifosize = uart_config[up->port.type].fifo_size;
+ old_capabilities = up->capabilities;
+ up->capabilities = uart_config[port->type].flags;
+ up->tx_loadsz = uart_config[port->type].tx_loadsz;
+
+ if (port->type == PORT_UNKNOWN)
+ goto out_lock;
+
+ /*
+ * Reset the UART.
+ */
+#ifdef CONFIG_SERIAL_8250_RSA
+ if (port->type == PORT_RSA)
+ serial_out(up, UART_RSA_FRR, 0);
+#endif
+ serial_out(up, UART_MCR, save_mcr);
+ serial8250_clear_fifos(up);
+ serial_in(up, UART_RX);
+ if (up->capabilities & UART_CAP_UUE)
+ serial_out(up, UART_IER, UART_IER_UUE);
+ else
+ serial_out(up, UART_IER, 0);
+
+out_lock:
+ spin_unlock_irqrestore(&port->lock, flags);
+ if (up->capabilities != old_capabilities) {
+ printk(KERN_WARNING
+ "ttyS%d: detected caps %08x should be %08x\n",
+ serial_index(port), old_capabilities,
+ up->capabilities);
+ }
+out:
+ DEBUG_AUTOCONF("iir=%d ", scratch);
+ DEBUG_AUTOCONF("type=%s\n", uart_config[port->type].name);
+}
+
+static void autoconfig_irq(struct uart_8250_port *up)
+{
+ struct uart_port *port = &up->port;
+ unsigned char save_mcr, save_ier;
+ unsigned char save_ICP = 0;
+ unsigned int ICP = 0;
+ unsigned long irqs;
+ int irq;
+
+ if (port->flags & UPF_FOURPORT) {
+ ICP = (port->iobase & 0xfe0) | 0x1f;
+ save_ICP = inb_p(ICP);
+ outb_p(0x80, ICP);
+ inb_p(ICP);
+ }
+
+ /* forget possible initially masked and pending IRQ */
+ probe_irq_off(probe_irq_on());
+ save_mcr = serial_in(up, UART_MCR);
+ save_ier = serial_in(up, UART_IER);
+ serial_out(up, UART_MCR, UART_MCR_OUT1 | UART_MCR_OUT2);
+
+ irqs = probe_irq_on();
+ serial_out(up, UART_MCR, 0);
+ udelay(10);
+ if (port->flags & UPF_FOURPORT) {
+ serial_out(up, UART_MCR,
+ UART_MCR_DTR | UART_MCR_RTS);
+ } else {
+ serial_out(up, UART_MCR,
+ UART_MCR_DTR | UART_MCR_RTS | UART_MCR_OUT2);
+ }
+ serial_out(up, UART_IER, 0x0f); /* enable all intrs */
+ serial_in(up, UART_LSR);
+ serial_in(up, UART_RX);
+ serial_in(up, UART_IIR);
+ serial_in(up, UART_MSR);
+ serial_out(up, UART_TX, 0xFF);
+ udelay(20);
+ irq = probe_irq_off(irqs);
+
+ serial_out(up, UART_MCR, save_mcr);
+ serial_out(up, UART_IER, save_ier);
+
+ if (port->flags & UPF_FOURPORT)
+ outb_p(save_ICP, ICP);
+
+ port->irq = (irq > 0) ? irq : 0;
+}
+
+static inline void __stop_tx(struct uart_8250_port *p)
+{
+ if (p->ier & UART_IER_THRI) {
+ p->ier &= ~UART_IER_THRI;
+ serial_out(p, UART_IER, p->ier);
+ serial8250_rpm_put_tx(p);
+ }
+}
+
+static void serial8250_stop_tx(struct uart_port *port)
+{
+ struct uart_8250_port *up = up_to_u8250p(port);
+
+ serial8250_rpm_get(up);
+ __stop_tx(up);
+
+ /*
+ * We really want to stop the transmitter from sending.
+ */
+ if (port->type == PORT_16C950) {
+ up->acr |= UART_ACR_TXDIS;
+ serial_icr_write(up, UART_ACR, up->acr);
+ }
+ serial8250_rpm_put(up);
+}
+
+static void serial8250_start_tx(struct uart_port *port)
+{
+ struct uart_8250_port *up = up_to_u8250p(port);
+
+ serial8250_rpm_get_tx(up);
+
+ if (up->dma && !up->dma->tx_dma(up))
+ return;
+
+ if (!(up->ier & UART_IER_THRI)) {
+ up->ier |= UART_IER_THRI;
+ serial_port_out(port, UART_IER, up->ier);
+
+ if (up->bugs & UART_BUG_TXEN) {
+ unsigned char lsr;
+ lsr = serial_in(up, UART_LSR);
+ up->lsr_saved_flags |= lsr & LSR_SAVE_FLAGS;
+ if (lsr & UART_LSR_THRE)
+ serial8250_tx_chars(up);
+ }
+ }
+
+ /*
+ * Re-enable the transmitter if we disabled it.
+ */
+ if (port->type == PORT_16C950 && up->acr & UART_ACR_TXDIS) {
+ up->acr &= ~UART_ACR_TXDIS;
+ serial_icr_write(up, UART_ACR, up->acr);
+ }
+}
+
+static void serial8250_throttle(struct uart_port *port)
+{
+ port->throttle(port);
+}
+
+static void serial8250_unthrottle(struct uart_port *port)
+{
+ port->unthrottle(port);
+}
+
+static void serial8250_stop_rx(struct uart_port *port)
+{
+ struct uart_8250_port *up = up_to_u8250p(port);
+
+ serial8250_rpm_get(up);
+
+ up->ier &= ~(UART_IER_RLSI | UART_IER_RDI);
+ up->port.read_status_mask &= ~UART_LSR_DR;
+ serial_port_out(port, UART_IER, up->ier);
+
+ serial8250_rpm_put(up);
+}
+
+static void serial8250_disable_ms(struct uart_port *port)
+{
+ struct uart_8250_port *up =
+ container_of(port, struct uart_8250_port, port);
+
+ /* no MSR capabilities */
+ if (up->bugs & UART_BUG_NOMSR)
+ return;
+
+ up->ier &= ~UART_IER_MSI;
+ serial_port_out(port, UART_IER, up->ier);
+}
+
+static void serial8250_enable_ms(struct uart_port *port)
+{
+ struct uart_8250_port *up = up_to_u8250p(port);
+
+ /* no MSR capabilities */
+ if (up->bugs & UART_BUG_NOMSR)
+ return;
+
+ up->ier |= UART_IER_MSI;
+
+ serial8250_rpm_get(up);
+ serial_port_out(port, UART_IER, up->ier);
+ serial8250_rpm_put(up);
+}
+
+/*
+ * serial8250_rx_chars: processes according to the passed in LSR
+ * value, and returns the remaining LSR bits not handled
+ * by this Rx routine.
+ */
+unsigned char
+serial8250_rx_chars(struct uart_8250_port *up, unsigned char lsr)
+{
+ struct uart_port *port = &up->port;
+ unsigned char ch;
+ int max_count = 256;
+ char flag;
+
+ do {
+ if (likely(lsr & UART_LSR_DR))
+ ch = serial_in(up, UART_RX);
+ else
+ /*
+ * Intel 82571 has a Serial Over Lan device that will
+ * set UART_LSR_BI without setting UART_LSR_DR when
+ * it receives a break. To avoid reading from the
+ * receive buffer without UART_LSR_DR bit set, we
+ * just force the read character to be 0
+ */
+ ch = 0;
+
+ flag = TTY_NORMAL;
+ port->icount.rx++;
+
+ lsr |= up->lsr_saved_flags;
+ up->lsr_saved_flags = 0;
+
+ if (unlikely(lsr & UART_LSR_BRK_ERROR_BITS)) {
+ if (lsr & UART_LSR_BI) {
+ lsr &= ~(UART_LSR_FE | UART_LSR_PE);
+ port->icount.brk++;
+ /*
+ * We do the SysRQ and SAK checking
+ * here because otherwise the break
+ * may get masked by ignore_status_mask
+ * or read_status_mask.
+ */
+ if (uart_handle_break(port))
+ goto ignore_char;
+ } else if (lsr & UART_LSR_PE)
+ port->icount.parity++;
+ else if (lsr & UART_LSR_FE)
+ port->icount.frame++;
+ if (lsr & UART_LSR_OE)
+ port->icount.overrun++;
+
+ /*
+ * Mask off conditions which should be ignored.
+ */
+ lsr &= port->read_status_mask;
+
+ if (lsr & UART_LSR_BI) {
+ DEBUG_INTR("handling break....");
+ flag = TTY_BREAK;
+ } else if (lsr & UART_LSR_PE)
+ flag = TTY_PARITY;
+ else if (lsr & UART_LSR_FE)
+ flag = TTY_FRAME;
+ }
+ if (uart_handle_sysrq_char(port, ch))
+ goto ignore_char;
+
+ uart_insert_char(port, lsr, UART_LSR_OE, ch, flag);
+
+ignore_char:
+ lsr = serial_in(up, UART_LSR);
+ } while ((lsr & (UART_LSR_DR | UART_LSR_BI)) && (--max_count > 0));
+ spin_unlock(&port->lock);
+ tty_flip_buffer_push(&port->state->port);
+ spin_lock(&port->lock);
+ return lsr;
+}
+EXPORT_SYMBOL_GPL(serial8250_rx_chars);
+
+void serial8250_tx_chars(struct uart_8250_port *up)
+{
+ struct uart_port *port = &up->port;
+ struct circ_buf *xmit = &port->state->xmit;
+ int count;
+
+ if (port->x_char) {
+ serial_out(up, UART_TX, port->x_char);
+ port->icount.tx++;
+ port->x_char = 0;
+ return;
+ }
+ if (uart_tx_stopped(port)) {
+ serial8250_stop_tx(port);
+ return;
+ }
+ if (uart_circ_empty(xmit)) {
+ __stop_tx(up);
+ return;
+ }
+
+ count = up->tx_loadsz;
+ do {
+ serial_out(up, UART_TX, xmit->buf[xmit->tail]);
+ xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
+ port->icount.tx++;
+ if (uart_circ_empty(xmit))
+ break;
+ if (up->capabilities & UART_CAP_HFIFO) {
+ if ((serial_port_in(port, UART_LSR) & BOTH_EMPTY) !=
+ BOTH_EMPTY)
+ break;
+ }
+ } while (--count > 0);
+
+ if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
+ uart_write_wakeup(port);
+
+ DEBUG_INTR("THRE...");
+
+ /*
+ * With RPM enabled, we have to wait until the FIFO is empty before the
+ * HW can go idle. So we get here once again with empty FIFO and disable
+ * the interrupt and RPM in __stop_tx()
+ */
+ if (uart_circ_empty(xmit) && !(up->capabilities & UART_CAP_RPM))
+ __stop_tx(up);
+}
+EXPORT_SYMBOL_GPL(serial8250_tx_chars);
+
+/* Caller holds uart port lock */
+unsigned int serial8250_modem_status(struct uart_8250_port *up)
+{
+ struct uart_port *port = &up->port;
+ unsigned int status = serial_in(up, UART_MSR);
+
+ status |= up->msr_saved_flags;
+ up->msr_saved_flags = 0;
+ if (status & UART_MSR_ANY_DELTA && up->ier & UART_IER_MSI &&
+ port->state != NULL) {
+ if (status & UART_MSR_TERI)
+ port->icount.rng++;
+ if (status & UART_MSR_DDSR)
+ port->icount.dsr++;
+ if (status & UART_MSR_DDCD)
+ uart_handle_dcd_change(port, status & UART_MSR_DCD);
+ if (status & UART_MSR_DCTS)
+ uart_handle_cts_change(port, status & UART_MSR_CTS);
+
+ wake_up_interruptible(&port->state->port.delta_msr_wait);
+ }
+
+ return status;
+}
+EXPORT_SYMBOL_GPL(serial8250_modem_status);
+
+/*
+ * This handles the interrupt from one port.
+ */
+int serial8250_handle_irq(struct uart_port *port, unsigned int iir)
+{
+ unsigned char status;
+ unsigned long flags;
+ struct uart_8250_port *up = up_to_u8250p(port);
+ int dma_err = 0;
+
+ if (iir & UART_IIR_NO_INT)
+ return 0;
+
+ spin_lock_irqsave(&port->lock, flags);
+
+ status = serial_port_in(port, UART_LSR);
+
+ DEBUG_INTR("status = %x...", status);
+
+ if (status & (UART_LSR_DR | UART_LSR_BI)) {
+ if (up->dma)
+ dma_err = up->dma->rx_dma(up, iir);
+
+ if (!up->dma || dma_err)
+ status = serial8250_rx_chars(up, status);
+ }
+ serial8250_modem_status(up);
+ if ((!up->dma || (up->dma && up->dma->tx_err)) &&
+ (status & UART_LSR_THRE))
+ serial8250_tx_chars(up);
+
+ spin_unlock_irqrestore(&port->lock, flags);
+ return 1;
+}
+EXPORT_SYMBOL_GPL(serial8250_handle_irq);
+
+static int serial8250_default_handle_irq(struct uart_port *port)
+{
+ struct uart_8250_port *up = up_to_u8250p(port);
+ unsigned int iir;
+ int ret;
+
+ serial8250_rpm_get(up);
+
+ iir = serial_port_in(port, UART_IIR);
+ ret = serial8250_handle_irq(port, iir);
+
+ serial8250_rpm_put(up);
+ return ret;
+}
+
+/*
+ * These Exar UARTs have an extra interrupt indicator that could
+ * fire for a few unimplemented interrupts. One of which is a
+ * wakeup event when coming out of sleep. Put this here just
+ * to be on the safe side that these interrupts don't go unhandled.
+ */
+static int exar_handle_irq(struct uart_port *port)
+{
+ unsigned char int0, int1, int2, int3;
+ unsigned int iir = serial_port_in(port, UART_IIR);
+ int ret;
+
+ ret = serial8250_handle_irq(port, iir);
+
+ if ((port->type == PORT_XR17V35X) ||
+ (port->type == PORT_XR17D15X)) {
+ int0 = serial_port_in(port, 0x80);
+ int1 = serial_port_in(port, 0x81);
+ int2 = serial_port_in(port, 0x82);
+ int3 = serial_port_in(port, 0x83);
+ }
+
+ return ret;
+}
+
+static unsigned int serial8250_tx_empty(struct uart_port *port)
+{
+ struct uart_8250_port *up = up_to_u8250p(port);
+ unsigned long flags;
+ unsigned int lsr;
+
+ serial8250_rpm_get(up);
+
+ spin_lock_irqsave(&port->lock, flags);
+ lsr = serial_port_in(port, UART_LSR);
+ up->lsr_saved_flags |= lsr & LSR_SAVE_FLAGS;
+ spin_unlock_irqrestore(&port->lock, flags);
+
+ serial8250_rpm_put(up);
+
+ return (lsr & BOTH_EMPTY) == BOTH_EMPTY ? TIOCSER_TEMT : 0;
+}
+
+static unsigned int serial8250_get_mctrl(struct uart_port *port)
+{
+ struct uart_8250_port *up = up_to_u8250p(port);
+ unsigned int status;
+ unsigned int ret;
+
+ serial8250_rpm_get(up);
+ status = serial8250_modem_status(up);
+ serial8250_rpm_put(up);
+
+ ret = 0;
+ if (status & UART_MSR_DCD)
+ ret |= TIOCM_CAR;
+ if (status & UART_MSR_RI)
+ ret |= TIOCM_RNG;
+ if (status & UART_MSR_DSR)
+ ret |= TIOCM_DSR;
+ if (status & UART_MSR_CTS)
+ ret |= TIOCM_CTS;
+ return ret;
+}
+
+void serial8250_do_set_mctrl(struct uart_port *port, unsigned int mctrl)
+{
+ struct uart_8250_port *up = up_to_u8250p(port);
+ unsigned char mcr = 0;
+
+ if (mctrl & TIOCM_RTS)
+ mcr |= UART_MCR_RTS;
+ if (mctrl & TIOCM_DTR)
+ mcr |= UART_MCR_DTR;
+ if (mctrl & TIOCM_OUT1)
+ mcr |= UART_MCR_OUT1;
+ if (mctrl & TIOCM_OUT2)
+ mcr |= UART_MCR_OUT2;
+ if (mctrl & TIOCM_LOOP)
+ mcr |= UART_MCR_LOOP;
+
+ mcr = (mcr & up->mcr_mask) | up->mcr_force | up->mcr;
+
+ serial_port_out(port, UART_MCR, mcr);
+}
+EXPORT_SYMBOL_GPL(serial8250_do_set_mctrl);
+
+static void serial8250_set_mctrl(struct uart_port *port, unsigned int mctrl)
+{
+ if (port->set_mctrl)
+ port->set_mctrl(port, mctrl);
+ else
+ serial8250_do_set_mctrl(port, mctrl);
+}
+
+static void serial8250_break_ctl(struct uart_port *port, int break_state)
+{
+ struct uart_8250_port *up = up_to_u8250p(port);
+ unsigned long flags;
+
+ serial8250_rpm_get(up);
+ spin_lock_irqsave(&port->lock, flags);
+ if (break_state == -1)
+ up->lcr |= UART_LCR_SBC;
+ else
+ up->lcr &= ~UART_LCR_SBC;
+ serial_port_out(port, UART_LCR, up->lcr);
+ spin_unlock_irqrestore(&port->lock, flags);
+ serial8250_rpm_put(up);
+}
+
+/*
+ * Wait for transmitter & holding register to empty
+ */
+static void wait_for_xmitr(struct uart_8250_port *up, int bits)
+{
+ unsigned int status, tmout = 10000;
+
+ /* Wait up to 10ms for the character(s) to be sent. */
+ for (;;) {
+ status = serial_in(up, UART_LSR);
+
+ up->lsr_saved_flags |= status & LSR_SAVE_FLAGS;
+
+ if ((status & bits) == bits)
+ break;
+ if (--tmout == 0)
+ break;
+ udelay(1);
+ }
+
+ /* Wait up to 1s for flow control if necessary */
+ if (up->port.flags & UPF_CONS_FLOW) {
+ unsigned int tmout;
+ for (tmout = 1000000; tmout; tmout--) {
+ unsigned int msr = serial_in(up, UART_MSR);
+ up->msr_saved_flags |= msr & MSR_SAVE_FLAGS;
+ if (msr & UART_MSR_CTS)
+ break;
+ udelay(1);
+ touch_nmi_watchdog();
+ }
+ }
+}
+
+#ifdef CONFIG_CONSOLE_POLL
+/*
+ * Console polling routines for writing and reading from the uart while
+ * in an interrupt or debug context.
+ */
+
+static int serial8250_get_poll_char(struct uart_port *port)
+{
+ struct uart_8250_port *up = up_to_u8250p(port);
+ unsigned char lsr;
+ int status;
+
+ serial8250_rpm_get(up);
+
+ lsr = serial_port_in(port, UART_LSR);
+
+ if (!(lsr & UART_LSR_DR)) {
+ status = NO_POLL_CHAR;
+ goto out;
+ }
+
+ status = serial_port_in(port, UART_RX);
+out:
+ serial8250_rpm_put(up);
+ return status;
+}
+
+
+static void serial8250_put_poll_char(struct uart_port *port,
+ unsigned char c)
+{
+ unsigned int ier;
+ struct uart_8250_port *up = up_to_u8250p(port);
+
+ serial8250_rpm_get(up);
+ /*
+ * First save the IER then disable the interrupts
+ */
+ ier = serial_port_in(port, UART_IER);
+ if (up->capabilities & UART_CAP_UUE)
+ serial_port_out(port, UART_IER, UART_IER_UUE);
+ else
+ serial_port_out(port, UART_IER, 0);
+
+ wait_for_xmitr(up, BOTH_EMPTY);
+ /*
+ * Send the character out.
+ */
+ serial_port_out(port, UART_TX, c);
+
+ /*
+ * Finally, wait for transmitter to become empty
+ * and restore the IER
+ */
+ wait_for_xmitr(up, BOTH_EMPTY);
+ serial_port_out(port, UART_IER, ier);
+ serial8250_rpm_put(up);
+}
+
+#endif /* CONFIG_CONSOLE_POLL */
+
+int serial8250_do_startup(struct uart_port *port)
+{
+ struct uart_8250_port *up = up_to_u8250p(port);
+ unsigned long flags;
+ unsigned char lsr, iir;
+ int retval;
+
+ if (port->type == PORT_8250_CIR)
+ return -ENODEV;
+
+ if (!port->fifosize)
+ port->fifosize = uart_config[port->type].fifo_size;
+ if (!up->tx_loadsz)
+ up->tx_loadsz = uart_config[port->type].tx_loadsz;
+ if (!up->capabilities)
+ up->capabilities = uart_config[port->type].flags;
+ up->mcr = 0;
+
+ if (port->iotype != up->cur_iotype)
+ set_io_from_upio(port);
+
+ serial8250_rpm_get(up);
+ if (port->type == PORT_16C950) {
+ /* Wake up and initialize UART */
+ up->acr = 0;
+ serial_port_out(port, UART_LCR, UART_LCR_CONF_MODE_B);
+ serial_port_out(port, UART_EFR, UART_EFR_ECB);
+ serial_port_out(port, UART_IER, 0);
+ serial_port_out(port, UART_LCR, 0);
+ serial_icr_write(up, UART_CSR, 0); /* Reset the UART */
+ serial_port_out(port, UART_LCR, UART_LCR_CONF_MODE_B);
+ serial_port_out(port, UART_EFR, UART_EFR_ECB);
+ serial_port_out(port, UART_LCR, 0);
+ }
+
+#ifdef CONFIG_SERIAL_8250_RSA
+ /*
+ * If this is an RSA port, see if we can kick it up to the
+ * higher speed clock.
+ */
+ enable_rsa(up);
+#endif
+ /*
+ * Clear the FIFO buffers and disable them.
+ * (they will be reenabled in set_termios())
+ */
+ serial8250_clear_fifos(up);
+
+ /*
+ * Clear the interrupt registers.
+ */
+ serial_port_in(port, UART_LSR);
+ serial_port_in(port, UART_RX);
+ serial_port_in(port, UART_IIR);
+ serial_port_in(port, UART_MSR);
+
+ /*
+ * At this point, there's no way the LSR could still be 0xff;
+ * if it is, then bail out, because there's likely no UART
+ * here.
+ */
+ if (!(port->flags & UPF_BUGGY_UART) &&
+ (serial_port_in(port, UART_LSR) == 0xff)) {
+ printk_ratelimited(KERN_INFO "ttyS%d: LSR safety check engaged!\n",
+ serial_index(port));
+ retval = -ENODEV;
+ goto out;
+ }
+
+ /*
+ * For a XR16C850, we need to set the trigger levels
+ */
+ if (port->type == PORT_16850) {
+ unsigned char fctr;
+
+ serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
+
+ fctr = serial_in(up, UART_FCTR) & ~(UART_FCTR_RX|UART_FCTR_TX);
+ serial_port_out(port, UART_FCTR,
+ fctr | UART_FCTR_TRGD | UART_FCTR_RX);
+ serial_port_out(port, UART_TRG, UART_TRG_96);
+ serial_port_out(port, UART_FCTR,
+ fctr | UART_FCTR_TRGD | UART_FCTR_TX);
+ serial_port_out(port, UART_TRG, UART_TRG_96);
+
+ serial_port_out(port, UART_LCR, 0);
+ }
+
+ if (port->irq) {
+ unsigned char iir1;
+ /*
+ * Test for UARTs that do not reassert THRE when the
+ * transmitter is idle and the interrupt has already
+ * been cleared. Real 16550s should always reassert
+ * this interrupt whenever the transmitter is idle and
+ * the interrupt is enabled. Delays are necessary to
+ * allow register changes to become visible.
+ */
+ spin_lock_irqsave(&port->lock, flags);
+ if (up->port.irqflags & IRQF_SHARED)
+ disable_irq_nosync(port->irq);
+
+ wait_for_xmitr(up, UART_LSR_THRE);
+ serial_port_out_sync(port, UART_IER, UART_IER_THRI);
+ udelay(1); /* allow THRE to set */
+ iir1 = serial_port_in(port, UART_IIR);
+ serial_port_out(port, UART_IER, 0);
+ serial_port_out_sync(port, UART_IER, UART_IER_THRI);
+ udelay(1); /* allow a working UART time to re-assert THRE */
+ iir = serial_port_in(port, UART_IIR);
+ serial_port_out(port, UART_IER, 0);
+
+ if (port->irqflags & IRQF_SHARED)
+ enable_irq(port->irq);
+ spin_unlock_irqrestore(&port->lock, flags);
+
+ /*
+ * If the interrupt is not reasserted, or we otherwise
+ * don't trust the iir, setup a timer to kick the UART
+ * on a regular basis.
+ */
+ if ((!(iir1 & UART_IIR_NO_INT) && (iir & UART_IIR_NO_INT)) ||
+ up->port.flags & UPF_BUG_THRE) {
+ up->bugs |= UART_BUG_THRE;
+ }
+ }
+
+ retval = up->ops->setup_irq(up);
+ if (retval)
+ goto out;
+
+ /*
+ * Now, initialize the UART
+ */
+ serial_port_out(port, UART_LCR, UART_LCR_WLEN8);
+
+ spin_lock_irqsave(&port->lock, flags);
+ if (up->port.flags & UPF_FOURPORT) {
+ if (!up->port.irq)
+ up->port.mctrl |= TIOCM_OUT1;
+ } else
+ /*
+ * Most PC uarts need OUT2 raised to enable interrupts.
+ */
+ if (port->irq)
+ up->port.mctrl |= TIOCM_OUT2;
+
+ serial8250_set_mctrl(port, port->mctrl);
+
+ /* Serial over Lan (SoL) hack:
+ Intel 8257x Gigabit ethernet chips have a
+ 16550 emulation, to be used for Serial Over Lan.
+ Those chips take a longer time than a normal
+ serial device to signalize that a transmission
+ data was queued. Due to that, the above test generally
+ fails. One solution would be to delay the reading of
+ iir. However, this is not reliable, since the timeout
+ is variable. So, let's just don't test if we receive
+ TX irq. This way, we'll never enable UART_BUG_TXEN.
+ */
+ if (up->port.flags & UPF_NO_TXEN_TEST)
+ goto dont_test_tx_en;
+
+ /*
+ * Do a quick test to see if we receive an
+ * interrupt when we enable the TX irq.
+ */
+ serial_port_out(port, UART_IER, UART_IER_THRI);
+ lsr = serial_port_in(port, UART_LSR);
+ iir = serial_port_in(port, UART_IIR);
+ serial_port_out(port, UART_IER, 0);
+
+ if (lsr & UART_LSR_TEMT && iir & UART_IIR_NO_INT) {
+ if (!(up->bugs & UART_BUG_TXEN)) {
+ up->bugs |= UART_BUG_TXEN;
+ pr_debug("ttyS%d - enabling bad tx status workarounds\n",
+ serial_index(port));
+ }
+ } else {
+ up->bugs &= ~UART_BUG_TXEN;
+ }
+
+dont_test_tx_en:
+ spin_unlock_irqrestore(&port->lock, flags);
+
+ /*
+ * Clear the interrupt registers again for luck, and clear the
+ * saved flags to avoid getting false values from polling
+ * routines or the previous session.
+ */
+ serial_port_in(port, UART_LSR);
+ serial_port_in(port, UART_RX);
+ serial_port_in(port, UART_IIR);
+ serial_port_in(port, UART_MSR);
+ up->lsr_saved_flags = 0;
+ up->msr_saved_flags = 0;
+
+ /*
+ * Request DMA channels for both RX and TX.
+ */
+ if (up->dma) {
+ retval = serial8250_request_dma(up);
+ if (retval) {
+ pr_warn_ratelimited("ttyS%d - failed to request DMA\n",
+ serial_index(port));
+ up->dma = NULL;
+ }
+ }
+
+ /*
+ * Finally, enable interrupts. Note: Modem status interrupts
+ * are set via set_termios(), which will be occurring imminently
+ * anyway, so we don't enable them here.
+ */
+ up->ier = UART_IER_RLSI | UART_IER_RDI;
+ serial_port_out(port, UART_IER, up->ier);
+
+ if (port->flags & UPF_FOURPORT) {
+ unsigned int icp;
+ /*
+ * Enable interrupts on the AST Fourport board
+ */
+ icp = (port->iobase & 0xfe0) | 0x01f;
+ outb_p(0x80, icp);
+ inb_p(icp);
+ }
+ retval = 0;
+out:
+ serial8250_rpm_put(up);
+ return retval;
+}
+EXPORT_SYMBOL_GPL(serial8250_do_startup);
+
+static int serial8250_startup(struct uart_port *port)
+{
+ if (port->startup)
+ return port->startup(port);
+ return serial8250_do_startup(port);
+}
+
+void serial8250_do_shutdown(struct uart_port *port)
+{
+ struct uart_8250_port *up = up_to_u8250p(port);
+ unsigned long flags;
+
+ serial8250_rpm_get(up);
+ /*
+ * Disable interrupts from this port
+ */
+ up->ier = 0;
+ serial_port_out(port, UART_IER, 0);
+
+ if (up->dma)
+ serial8250_release_dma(up);
+
+ spin_lock_irqsave(&port->lock, flags);
+ if (port->flags & UPF_FOURPORT) {
+ /* reset interrupts on the AST Fourport board */
+ inb((port->iobase & 0xfe0) | 0x1f);
+ port->mctrl |= TIOCM_OUT1;
+ } else
+ port->mctrl &= ~TIOCM_OUT2;
+
+ serial8250_set_mctrl(port, port->mctrl);
+ spin_unlock_irqrestore(&port->lock, flags);
+
+ /*
+ * Disable break condition and FIFOs
+ */
+ serial_port_out(port, UART_LCR,
+ serial_port_in(port, UART_LCR) & ~UART_LCR_SBC);
+ serial8250_clear_fifos(up);
+
+#ifdef CONFIG_SERIAL_8250_RSA
+ /*
+ * Reset the RSA board back to 115kbps compat mode.
+ */
+ disable_rsa(up);
+#endif
+
+ /*
+ * Read data port to reset things, and then unlink from
+ * the IRQ chain.
+ */
+ serial_port_in(port, UART_RX);
+ serial8250_rpm_put(up);
+
+ up->ops->release_irq(up);
+}
+EXPORT_SYMBOL_GPL(serial8250_do_shutdown);
+
+static void serial8250_shutdown(struct uart_port *port)
+{
+ if (port->shutdown)
+ port->shutdown(port);
+ else
+ serial8250_do_shutdown(port);
+}
+
+/*
+ * XR17V35x UARTs have an extra fractional divisor register (DLD)
+ * Calculate divisor with extra 4-bit fractional portion
+ */
+static unsigned int xr17v35x_get_divisor(struct uart_8250_port *up,
+ unsigned int baud,
+ unsigned int *frac)
+{
+ struct uart_port *port = &up->port;
+ unsigned int quot_16;
+
+ quot_16 = DIV_ROUND_CLOSEST(port->uartclk, baud);
+ *frac = quot_16 & 0x0f;
+
+ return quot_16 >> 4;
+}
+
+static unsigned int serial8250_get_divisor(struct uart_8250_port *up,
+ unsigned int baud,
+ unsigned int *frac)
+{
+ struct uart_port *port = &up->port;
+ unsigned int quot;
+
+ /*
+ * Handle magic divisors for baud rates above baud_base on
+ * SMSC SuperIO chips.
+ *
+ */
+ if ((port->flags & UPF_MAGIC_MULTIPLIER) &&
+ baud == (port->uartclk/4))
+ quot = 0x8001;
+ else if ((port->flags & UPF_MAGIC_MULTIPLIER) &&
+ baud == (port->uartclk/8))
+ quot = 0x8002;
+ else if (up->port.type == PORT_XR17V35X)
+ quot = xr17v35x_get_divisor(up, baud, frac);
+ else
+ quot = uart_get_divisor(port, baud);
+
+ /*
+ * Oxford Semi 952 rev B workaround
+ */
+ if (up->bugs & UART_BUG_QUOT && (quot & 0xff) == 0)
+ quot++;
+
+ return quot;
+}
+
+static unsigned char serial8250_compute_lcr(struct uart_8250_port *up,
+ tcflag_t c_cflag)
+{
+ unsigned char cval;
+
+ switch (c_cflag & CSIZE) {
+ case CS5:
+ cval = UART_LCR_WLEN5;
+ break;
+ case CS6:
+ cval = UART_LCR_WLEN6;
+ break;
+ case CS7:
+ cval = UART_LCR_WLEN7;
+ break;
+ default:
+ case CS8:
+ cval = UART_LCR_WLEN8;
+ break;
+ }
+
+ if (c_cflag & CSTOPB)
+ cval |= UART_LCR_STOP;
+ if (c_cflag & PARENB) {
+ cval |= UART_LCR_PARITY;
+ if (up->bugs & UART_BUG_PARITY)
+ up->fifo_bug = true;
+ }
+ if (!(c_cflag & PARODD))
+ cval |= UART_LCR_EPAR;
+#ifdef CMSPAR
+ if (c_cflag & CMSPAR)
+ cval |= UART_LCR_SPAR;
+#endif
+
+ return cval;
+}
+
+static void serial8250_set_divisor(struct uart_port *port, unsigned int baud,
+ unsigned int quot, unsigned int quot_frac)
+{
+ struct uart_8250_port *up = up_to_u8250p(port);
+
+ /* Workaround to enable 115200 baud on OMAP1510 internal ports */
+ if (is_omap1510_8250(up)) {
+ if (baud == 115200) {
+ quot = 1;
+ serial_port_out(port, UART_OMAP_OSC_12M_SEL, 1);
+ } else
+ serial_port_out(port, UART_OMAP_OSC_12M_SEL, 0);
+ }
+
+ /*
+ * For NatSemi, switch to bank 2 not bank 1, to avoid resetting EXCR2,
+ * otherwise just set DLAB
+ */
+ if (up->capabilities & UART_NATSEMI)
+ serial_port_out(port, UART_LCR, 0xe0);
+ else
+ serial_port_out(port, UART_LCR, up->lcr | UART_LCR_DLAB);
+
+ serial_dl_write(up, quot);
+
+ /* XR17V35x UARTs have an extra fractional divisor register (DLD) */
+ if (up->port.type == PORT_XR17V35X)
+ serial_port_out(port, 0x2, quot_frac);
+}
+
+void
+serial8250_do_set_termios(struct uart_port *port, struct ktermios *termios,
+ struct ktermios *old)
+{
+ struct uart_8250_port *up = up_to_u8250p(port);
+ unsigned char cval;
+ unsigned long flags;
+ unsigned int baud, quot, frac = 0;
+
+ cval = serial8250_compute_lcr(up, termios->c_cflag);
+
+ /*
+ * Ask the core to calculate the divisor for us.
+ */
+ baud = uart_get_baud_rate(port, termios, old,
+ port->uartclk / 16 / 0xffff,
+ port->uartclk / 16);
+ quot = serial8250_get_divisor(up, baud, &frac);
+
+ /*
+ * Ok, we're now changing the port state. Do it with
+ * interrupts disabled.
+ */
+ serial8250_rpm_get(up);
+ spin_lock_irqsave(&port->lock, flags);
+
+ up->lcr = cval; /* Save computed LCR */
+
+ if (up->capabilities & UART_CAP_FIFO && port->fifosize > 1) {
+ /* NOTE: If fifo_bug is not set, a user can set RX_trigger. */
+ if ((baud < 2400 && !up->dma) || up->fifo_bug) {
+ up->fcr &= ~UART_FCR_TRIGGER_MASK;
+ up->fcr |= UART_FCR_TRIGGER_1;
+ }
+ }
+
+ /*
+ * MCR-based auto flow control. When AFE is enabled, RTS will be
+ * deasserted when the receive FIFO contains more characters than
+ * the trigger, or the MCR RTS bit is cleared. In the case where
+ * the remote UART is not using CTS auto flow control, we must
+ * have sufficient FIFO entries for the latency of the remote
+ * UART to respond. IOW, at least 32 bytes of FIFO.
+ */
+ if (up->capabilities & UART_CAP_AFE && port->fifosize >= 32) {
+ up->mcr &= ~UART_MCR_AFE;
+ if (termios->c_cflag & CRTSCTS)
+ up->mcr |= UART_MCR_AFE;
+ }
+
+ /*
+ * Update the per-port timeout.
+ */
+ uart_update_timeout(port, termios->c_cflag, baud);
+
+ port->read_status_mask = UART_LSR_OE | UART_LSR_THRE | UART_LSR_DR;
+ if (termios->c_iflag & INPCK)
+ port->read_status_mask |= UART_LSR_FE | UART_LSR_PE;
+ if (termios->c_iflag & (IGNBRK | BRKINT | PARMRK))
+ port->read_status_mask |= UART_LSR_BI;
+
+ /*
+ * Characteres to ignore
+ */
+ port->ignore_status_mask = 0;
+ if (termios->c_iflag & IGNPAR)
+ port->ignore_status_mask |= UART_LSR_PE | UART_LSR_FE;
+ if (termios->c_iflag & IGNBRK) {
+ port->ignore_status_mask |= UART_LSR_BI;
+ /*
+ * If we're ignoring parity and break indicators,
+ * ignore overruns too (for real raw support).
+ */
+ if (termios->c_iflag & IGNPAR)
+ port->ignore_status_mask |= UART_LSR_OE;
+ }
+
+ /*
+ * ignore all characters if CREAD is not set
+ */
+ if ((termios->c_cflag & CREAD) == 0)
+ port->ignore_status_mask |= UART_LSR_DR;
+
+ /*
+ * CTS flow control flag and modem status interrupts
+ */
+ up->ier &= ~UART_IER_MSI;
+ if (!(up->bugs & UART_BUG_NOMSR) &&
+ UART_ENABLE_MS(&up->port, termios->c_cflag))
+ up->ier |= UART_IER_MSI;
+ if (up->capabilities & UART_CAP_UUE)
+ up->ier |= UART_IER_UUE;
+ if (up->capabilities & UART_CAP_RTOIE)
+ up->ier |= UART_IER_RTOIE;
+
+ serial_port_out(port, UART_IER, up->ier);
+
+ if (up->capabilities & UART_CAP_EFR) {
+ unsigned char efr = 0;
+ /*
+ * TI16C752/Startech hardware flow control. FIXME:
+ * - TI16C752 requires control thresholds to be set.
+ * - UART_MCR_RTS is ineffective if auto-RTS mode is enabled.
+ */
+ if (termios->c_cflag & CRTSCTS)
+ efr |= UART_EFR_CTS;
+
+ serial_port_out(port, UART_LCR, UART_LCR_CONF_MODE_B);
+ if (port->flags & UPF_EXAR_EFR)
+ serial_port_out(port, UART_XR_EFR, efr);
+ else
+ serial_port_out(port, UART_EFR, efr);
+ }
+
+ serial8250_set_divisor(port, baud, quot, frac);
+
+ /*
+ * LCR DLAB must be set to enable 64-byte FIFO mode. If the FCR
+ * is written without DLAB set, this mode will be disabled.
+ */
+ if (port->type == PORT_16750)
+ serial_port_out(port, UART_FCR, up->fcr);
+
+ serial_port_out(port, UART_LCR, up->lcr); /* reset DLAB */
+ if (port->type != PORT_16750) {
+ /* emulated UARTs (Lucent Venus 167x) need two steps */
+ if (up->fcr & UART_FCR_ENABLE_FIFO)
+ serial_port_out(port, UART_FCR, UART_FCR_ENABLE_FIFO);
+ serial_port_out(port, UART_FCR, up->fcr); /* set fcr */
+ }
+ serial8250_set_mctrl(port, port->mctrl);
+ spin_unlock_irqrestore(&port->lock, flags);
+ serial8250_rpm_put(up);
+
+ /* Don't rewrite B0 */
+ if (tty_termios_baud_rate(termios))
+ tty_termios_encode_baud_rate(termios, baud, baud);
+}
+EXPORT_SYMBOL(serial8250_do_set_termios);
+
+static void
+serial8250_set_termios(struct uart_port *port, struct ktermios *termios,
+ struct ktermios *old)
+{
+ if (port->set_termios)
+ port->set_termios(port, termios, old);
+ else
+ serial8250_do_set_termios(port, termios, old);
+}
+
+static void
+serial8250_set_ldisc(struct uart_port *port, struct ktermios *termios)
+{
+ if (termios->c_line == N_PPS) {
+ port->flags |= UPF_HARDPPS_CD;
+ spin_lock_irq(&port->lock);
+ serial8250_enable_ms(port);
+ spin_unlock_irq(&port->lock);
+ } else {
+ port->flags &= ~UPF_HARDPPS_CD;
+ if (!UART_ENABLE_MS(port, termios->c_cflag)) {
+ spin_lock_irq(&port->lock);
+ serial8250_disable_ms(port);
+ spin_unlock_irq(&port->lock);
+ }
+ }
+}
+
+
+void serial8250_do_pm(struct uart_port *port, unsigned int state,
+ unsigned int oldstate)
+{
+ struct uart_8250_port *p = up_to_u8250p(port);
+
+ serial8250_set_sleep(p, state != 0);
+}
+EXPORT_SYMBOL(serial8250_do_pm);
+
+static void
+serial8250_pm(struct uart_port *port, unsigned int state,
+ unsigned int oldstate)
+{
+ if (port->pm)
+ port->pm(port, state, oldstate);
+ else
+ serial8250_do_pm(port, state, oldstate);
+}
+
+static unsigned int serial8250_port_size(struct uart_8250_port *pt)
+{
+ if (pt->port.mapsize)
+ return pt->port.mapsize;
+ if (pt->port.iotype == UPIO_AU) {
+ if (pt->port.type == PORT_RT2880)
+ return 0x100;
+ return 0x1000;
+ }
+ if (is_omap1_8250(pt))
+ return 0x16 << pt->port.regshift;
+
+ return 8 << pt->port.regshift;
+}
+
+/*
+ * Resource handling.
+ */
+static int serial8250_request_std_resource(struct uart_8250_port *up)
+{
+ unsigned int size = serial8250_port_size(up);
+ struct uart_port *port = &up->port;
+ int ret = 0;
+
+ switch (port->iotype) {
+ case UPIO_AU:
+ case UPIO_TSI:
+ case UPIO_MEM32:
+ case UPIO_MEM32BE:
+ case UPIO_MEM:
+ if (!port->mapbase)
+ break;
+
+ if (!request_mem_region(port->mapbase, size, "serial")) {
+ ret = -EBUSY;
+ break;
+ }
+
+ if (port->flags & UPF_IOREMAP) {
+ port->membase = ioremap_nocache(port->mapbase, size);
+ if (!port->membase) {
+ release_mem_region(port->mapbase, size);
+ ret = -ENOMEM;
+ }
+ }
+ break;
+
+ case UPIO_HUB6:
+ case UPIO_PORT:
+ if (!request_region(port->iobase, size, "serial"))
+ ret = -EBUSY;
+ break;
+ }
+ return ret;
+}
+
+static void serial8250_release_std_resource(struct uart_8250_port *up)
+{
+ unsigned int size = serial8250_port_size(up);
+ struct uart_port *port = &up->port;
+
+ switch (port->iotype) {
+ case UPIO_AU:
+ case UPIO_TSI:
+ case UPIO_MEM32:
+ case UPIO_MEM32BE:
+ case UPIO_MEM:
+ if (!port->mapbase)
+ break;
+
+ if (port->flags & UPF_IOREMAP) {
+ iounmap(port->membase);
+ port->membase = NULL;
+ }
+
+ release_mem_region(port->mapbase, size);
+ break;
+
+ case UPIO_HUB6:
+ case UPIO_PORT:
+ release_region(port->iobase, size);
+ break;
+ }
+}
+
+static void serial8250_release_port(struct uart_port *port)
+{
+ struct uart_8250_port *up = up_to_u8250p(port);
+
+ serial8250_release_std_resource(up);
+}
+
+static int serial8250_request_port(struct uart_port *port)
+{
+ struct uart_8250_port *up = up_to_u8250p(port);
+ int ret;
+
+ if (port->type == PORT_8250_CIR)
+ return -ENODEV;
+
+ ret = serial8250_request_std_resource(up);
+
+ return ret;
+}
+
+static int fcr_get_rxtrig_bytes(struct uart_8250_port *up)
+{
+ const struct serial8250_config *conf_type = &uart_config[up->port.type];
+ unsigned char bytes;
+
+ bytes = conf_type->rxtrig_bytes[UART_FCR_R_TRIG_BITS(up->fcr)];
+
+ return bytes ? bytes : -EOPNOTSUPP;
+}
+
+static int bytes_to_fcr_rxtrig(struct uart_8250_port *up, unsigned char bytes)
+{
+ const struct serial8250_config *conf_type = &uart_config[up->port.type];
+ int i;
+
+ if (!conf_type->rxtrig_bytes[UART_FCR_R_TRIG_BITS(UART_FCR_R_TRIG_00)])
+ return -EOPNOTSUPP;
+
+ for (i = 1; i < UART_FCR_R_TRIG_MAX_STATE; i++) {
+ if (bytes < conf_type->rxtrig_bytes[i])
+ /* Use the nearest lower value */
+ return (--i) << UART_FCR_R_TRIG_SHIFT;
+ }
+
+ return UART_FCR_R_TRIG_11;
+}
+
+static int do_get_rxtrig(struct tty_port *port)
+{
+ struct uart_state *state = container_of(port, struct uart_state, port);
+ struct uart_port *uport = state->uart_port;
+ struct uart_8250_port *up =
+ container_of(uport, struct uart_8250_port, port);
+
+ if (!(up->capabilities & UART_CAP_FIFO) || uport->fifosize <= 1)
+ return -EINVAL;
+
+ return fcr_get_rxtrig_bytes(up);
+}
+
+static int do_serial8250_get_rxtrig(struct tty_port *port)
+{
+ int rxtrig_bytes;
+
+ mutex_lock(&port->mutex);
+ rxtrig_bytes = do_get_rxtrig(port);
+ mutex_unlock(&port->mutex);
+
+ return rxtrig_bytes;
+}
+
+static ssize_t serial8250_get_attr_rx_trig_bytes(struct device *dev,
+ struct device_attribute *attr, char *buf)
+{
+ struct tty_port *port = dev_get_drvdata(dev);
+ int rxtrig_bytes;
+
+ rxtrig_bytes = do_serial8250_get_rxtrig(port);
+ if (rxtrig_bytes < 0)
+ return rxtrig_bytes;
+
+ return snprintf(buf, PAGE_SIZE, "%d\n", rxtrig_bytes);
+}
+
+static int do_set_rxtrig(struct tty_port *port, unsigned char bytes)
+{
+ struct uart_state *state = container_of(port, struct uart_state, port);
+ struct uart_port *uport = state->uart_port;
+ struct uart_8250_port *up =
+ container_of(uport, struct uart_8250_port, port);
+ int rxtrig;
+
+ if (!(up->capabilities & UART_CAP_FIFO) || uport->fifosize <= 1 ||
+ up->fifo_bug)
+ return -EINVAL;
+
+ rxtrig = bytes_to_fcr_rxtrig(up, bytes);
+ if (rxtrig < 0)
+ return rxtrig;
+
+ serial8250_clear_fifos(up);
+ up->fcr &= ~UART_FCR_TRIGGER_MASK;
+ up->fcr |= (unsigned char)rxtrig;
+ serial_out(up, UART_FCR, up->fcr);
+ return 0;
+}
+
+static int do_serial8250_set_rxtrig(struct tty_port *port, unsigned char bytes)
+{
+ int ret;
+
+ mutex_lock(&port->mutex);
+ ret = do_set_rxtrig(port, bytes);
+ mutex_unlock(&port->mutex);
+
+ return ret;
+}
+
+static ssize_t serial8250_set_attr_rx_trig_bytes(struct device *dev,
+ struct device_attribute *attr, const char *buf, size_t count)
+{
+ struct tty_port *port = dev_get_drvdata(dev);
+ unsigned char bytes;
+ int ret;
+
+ if (!count)
+ return -EINVAL;
+
+ ret = kstrtou8(buf, 10, &bytes);
+ if (ret < 0)
+ return ret;
+
+ ret = do_serial8250_set_rxtrig(port, bytes);
+ if (ret < 0)
+ return ret;
+
+ return count;
+}
+
+static DEVICE_ATTR(rx_trig_bytes, S_IRUSR | S_IWUSR | S_IRGRP,
+ serial8250_get_attr_rx_trig_bytes,
+ serial8250_set_attr_rx_trig_bytes);
+
+static struct attribute *serial8250_dev_attrs[] = {
+ &dev_attr_rx_trig_bytes.attr,
+ NULL,
+ };
+
+static struct attribute_group serial8250_dev_attr_group = {
+ .attrs = serial8250_dev_attrs,
+ };
+
+static void register_dev_spec_attr_grp(struct uart_8250_port *up)
+{
+ const struct serial8250_config *conf_type = &uart_config[up->port.type];
+
+ if (conf_type->rxtrig_bytes[0])
+ up->port.attr_group = &serial8250_dev_attr_group;
+}
+
+static void serial8250_config_port(struct uart_port *port, int flags)
+{
+ struct uart_8250_port *up = up_to_u8250p(port);
+ int ret;
+
+ if (port->type == PORT_8250_CIR)
+ return;
+
+ /*
+ * Find the region that we can probe for. This in turn
+ * tells us whether we can probe for the type of port.
+ */
+ ret = serial8250_request_std_resource(up);
+ if (ret < 0)
+ return;
+
+ if (port->iotype != up->cur_iotype)
+ set_io_from_upio(port);
+
+ if (flags & UART_CONFIG_TYPE)
+ autoconfig(up);
+
+ /* if access method is AU, it is a 16550 with a quirk */
+ if (port->type == PORT_16550A && port->iotype == UPIO_AU)
+ up->bugs |= UART_BUG_NOMSR;
+
+ /* HW bugs may trigger IRQ while IIR == NO_INT */
+ if (port->type == PORT_TEGRA)
+ up->bugs |= UART_BUG_NOMSR;
+
+ if (port->type != PORT_UNKNOWN && flags & UART_CONFIG_IRQ)
+ autoconfig_irq(up);
+
+ if (port->type == PORT_UNKNOWN)
+ serial8250_release_std_resource(up);
+
+ /* Fixme: probably not the best place for this */
+ if ((port->type == PORT_XR17V35X) ||
+ (port->type == PORT_XR17D15X))
+ port->handle_irq = exar_handle_irq;
+
+ register_dev_spec_attr_grp(up);
+ up->fcr = uart_config[up->port.type].fcr;
+}
+
+static int
+serial8250_verify_port(struct uart_port *port, struct serial_struct *ser)
+{
+ if (ser->irq >= nr_irqs || ser->irq < 0 ||
+ ser->baud_base < 9600 || ser->type < PORT_UNKNOWN ||
+ ser->type >= ARRAY_SIZE(uart_config) || ser->type == PORT_CIRRUS ||
+ ser->type == PORT_STARTECH)
+ return -EINVAL;
+ return 0;
+}
+
+static const char *
+serial8250_type(struct uart_port *port)
+{
+ int type = port->type;
+
+ if (type >= ARRAY_SIZE(uart_config))
+ type = 0;
+ return uart_config[type].name;
+}
+
+static const struct uart_ops serial8250_pops = {
+ .tx_empty = serial8250_tx_empty,
+ .set_mctrl = serial8250_set_mctrl,
+ .get_mctrl = serial8250_get_mctrl,
+ .stop_tx = serial8250_stop_tx,
+ .start_tx = serial8250_start_tx,
+ .throttle = serial8250_throttle,
+ .unthrottle = serial8250_unthrottle,
+ .stop_rx = serial8250_stop_rx,
+ .enable_ms = serial8250_enable_ms,
+ .break_ctl = serial8250_break_ctl,
+ .startup = serial8250_startup,
+ .shutdown = serial8250_shutdown,
+ .set_termios = serial8250_set_termios,
+ .set_ldisc = serial8250_set_ldisc,
+ .pm = serial8250_pm,
+ .type = serial8250_type,
+ .release_port = serial8250_release_port,
+ .request_port = serial8250_request_port,
+ .config_port = serial8250_config_port,
+ .verify_port = serial8250_verify_port,
+#ifdef CONFIG_CONSOLE_POLL
+ .poll_get_char = serial8250_get_poll_char,
+ .poll_put_char = serial8250_put_poll_char,
+#endif
+};
+
+void serial8250_init_port(struct uart_8250_port *up)
+{
+ struct uart_port *port = &up->port;
+
+ spin_lock_init(&port->lock);
+ port->ops = &serial8250_pops;
+
+ up->cur_iotype = 0xFF;
+}
+EXPORT_SYMBOL_GPL(serial8250_init_port);
+
+void serial8250_set_defaults(struct uart_8250_port *up)
+{
+ struct uart_port *port = &up->port;
+
+ if (up->port.flags & UPF_FIXED_TYPE) {
+ unsigned int type = up->port.type;
+
+ if (!up->port.fifosize)
+ up->port.fifosize = uart_config[type].fifo_size;
+ if (!up->tx_loadsz)
+ up->tx_loadsz = uart_config[type].tx_loadsz;
+ if (!up->capabilities)
+ up->capabilities = uart_config[type].flags;
+ }
+
+ set_io_from_upio(port);
+
+ /* default dma handlers */
+ if (up->dma) {
+ if (!up->dma->tx_dma)
+ up->dma->tx_dma = serial8250_tx_dma;
+ if (!up->dma->rx_dma)
+ up->dma->rx_dma = serial8250_rx_dma;
+ }
+}
+EXPORT_SYMBOL_GPL(serial8250_set_defaults);
+
+#ifdef CONFIG_SERIAL_8250_CONSOLE
+
+static void serial8250_console_putchar(struct uart_port *port, int ch)
+{
+ struct uart_8250_port *up = up_to_u8250p(port);
+
+ wait_for_xmitr(up, UART_LSR_THRE);
+ serial_port_out(port, UART_TX, ch);
+}
+
+/*
+ * Print a string to the serial port trying not to disturb
+ * any possible real use of the port...
+ *
+ * The console_lock must be held when we get here.
+ */
+void serial8250_console_write(struct uart_8250_port *up, const char *s,
+ unsigned int count)
+{
+ struct uart_port *port = &up->port;
+ unsigned long flags;
+ unsigned int ier;
+ int locked = 1;
+
+ touch_nmi_watchdog();
+
+ serial8250_rpm_get(up);
+
+ if (port->sysrq)
+ locked = 0;
+ else if (oops_in_progress)
+ locked = spin_trylock_irqsave(&port->lock, flags);
+ else
+ spin_lock_irqsave(&port->lock, flags);
+
+ /*
+ * First save the IER then disable the interrupts
+ */
+ ier = serial_port_in(port, UART_IER);
+
+ if (up->capabilities & UART_CAP_UUE)
+ serial_port_out(port, UART_IER, UART_IER_UUE);
+ else
+ serial_port_out(port, UART_IER, 0);
+
+ /* check scratch reg to see if port powered off during system sleep */
+ if (up->canary && (up->canary != serial_port_in(port, UART_SCR))) {
+ struct ktermios termios;
+ unsigned int baud, quot, frac = 0;
+
+ termios.c_cflag = port->cons->cflag;
+ if (port->state->port.tty && termios.c_cflag == 0)
+ termios.c_cflag = port->state->port.tty->termios.c_cflag;
+
+ baud = uart_get_baud_rate(port, &termios, NULL,
+ port->uartclk / 16 / 0xffff,
+ port->uartclk / 16);
+ quot = serial8250_get_divisor(up, baud, &frac);
+
+ serial8250_set_divisor(port, baud, quot, frac);
+ serial_port_out(port, UART_LCR, up->lcr);
+ serial_port_out(port, UART_MCR, UART_MCR_DTR | UART_MCR_RTS);
+
+ up->canary = 0;
+ }
+
+ uart_console_write(port, s, count, serial8250_console_putchar);
+
+ /*
+ * Finally, wait for transmitter to become empty
+ * and restore the IER
+ */
+ wait_for_xmitr(up, BOTH_EMPTY);
+ serial_port_out(port, UART_IER, ier);
+
+ /*
+ * The receive handling will happen properly because the
+ * receive ready bit will still be set; it is not cleared
+ * on read. However, modem control will not, we must
+ * call it if we have saved something in the saved flags
+ * while processing with interrupts off.
+ */
+ if (up->msr_saved_flags)
+ serial8250_modem_status(up);
+
+ if (locked)
+ spin_unlock_irqrestore(&port->lock, flags);
+ serial8250_rpm_put(up);
+}
+
+static unsigned int probe_baud(struct uart_port *port)
+{
+ unsigned char lcr, dll, dlm;
+ unsigned int quot;
+
+ lcr = serial_port_in(port, UART_LCR);
+ serial_port_out(port, UART_LCR, lcr | UART_LCR_DLAB);
+ dll = serial_port_in(port, UART_DLL);
+ dlm = serial_port_in(port, UART_DLM);
+ serial_port_out(port, UART_LCR, lcr);
+
+ quot = (dlm << 8) | dll;
+ return (port->uartclk / 16) / quot;
+}
+
+int serial8250_console_setup(struct uart_port *port, char *options, bool probe)
+{
+ int baud = 9600;
+ int bits = 8;
+ int parity = 'n';
+ int flow = 'n';
+
+ if (!port->iobase && !port->membase)
+ return -ENODEV;
+
+ if (options)
+ uart_parse_options(options, &baud, &parity, &bits, &flow);
+ else if (probe)
+ baud = probe_baud(port);
+
+ return uart_set_options(port, port->cons, baud, parity, bits, flow);
+}
+
+#endif /* CONFIG_SERIAL_8250_CONSOLE */
diff --git a/drivers/tty/serial/8250/Makefile b/drivers/tty/serial/8250/Makefile
index 7062959..39c6d22 100644
--- a/drivers/tty/serial/8250/Makefile
+++ b/drivers/tty/serial/8250/Makefile
@@ -2,10 +2,11 @@
# Makefile for the 8250 serial device drivers.
#
-obj-$(CONFIG_SERIAL_8250) += 8250.o
+obj-$(CONFIG_SERIAL_8250) += 8250.o 8250_base.o
8250-y := 8250_core.o
8250-$(CONFIG_SERIAL_8250_PNP) += 8250_pnp.o
-8250-$(CONFIG_SERIAL_8250_DMA) += 8250_dma.o
+8250_base-y := 8250_port.o
+8250_base-$(CONFIG_SERIAL_8250_DMA) += 8250_dma.o
obj-$(CONFIG_SERIAL_8250_GSC) += 8250_gsc.o
obj-$(CONFIG_SERIAL_8250_PCI) += 8250_pci.o
obj-$(CONFIG_SERIAL_8250_HP300) += 8250_hp300.o
diff --git a/include/linux/serial_8250.h b/include/linux/serial_8250.h
index ba82c07..7f156bd 100644
--- a/include/linux/serial_8250.h
+++ b/include/linux/serial_8250.h
@@ -152,6 +152,11 @@
unsigned char serial8250_rx_chars(struct uart_8250_port *up, unsigned char lsr);
void serial8250_tx_chars(struct uart_8250_port *up);
unsigned int serial8250_modem_status(struct uart_8250_port *up);
+void serial8250_init_port(struct uart_8250_port *up);
+void serial8250_set_defaults(struct uart_8250_port *up);
+void serial8250_console_write(struct uart_8250_port *up, const char *s,
+ unsigned int count);
+int serial8250_console_setup(struct uart_port *port, char *options, bool probe);
extern void serial8250_set_isa_configurator(void (*v)
(int port, struct uart_port *up,