diff --git a/drivers/net/phy/Kconfig b/drivers/net/phy/Kconfig
index 9b5d46c..6a17f92 100644
--- a/drivers/net/phy/Kconfig
+++ b/drivers/net/phy/Kconfig
@@ -71,6 +71,12 @@
 	---help---
 	  Currently supports the 6348 and 6358 PHYs.
 
+config BCM7XXX_PHY
+	tristate "Drivers for Broadcom 7xxx SOCs internal PHYs"
+	---help---
+	  Currently supports the BCM7366, BCM7439, BCM7445, and
+	  40nm and 65nm generation of BCM7xxx Set Top Box SoCs.
+
 config BCM87XX_PHY
 	tristate "Driver for Broadcom BCM8706 and BCM8727 PHYs"
 	help
diff --git a/drivers/net/phy/Makefile b/drivers/net/phy/Makefile
index 9013dfa..07d2402 100644
--- a/drivers/net/phy/Makefile
+++ b/drivers/net/phy/Makefile
@@ -12,6 +12,7 @@
 obj-$(CONFIG_VITESSE_PHY)	+= vitesse.o
 obj-$(CONFIG_BROADCOM_PHY)	+= broadcom.o
 obj-$(CONFIG_BCM63XX_PHY)	+= bcm63xx.o
+obj-$(CONFIG_BCM7XXX_PHY)	+= bcm7xxx.o
 obj-$(CONFIG_BCM87XX_PHY)	+= bcm87xx.o
 obj-$(CONFIG_ICPLUS_PHY)	+= icplus.o
 obj-$(CONFIG_REALTEK_PHY)	+= realtek.o
diff --git a/drivers/net/phy/bcm7xxx.c b/drivers/net/phy/bcm7xxx.c
new file mode 100644
index 0000000..6973372
--- /dev/null
+++ b/drivers/net/phy/bcm7xxx.c
@@ -0,0 +1,343 @@
+/*
+ * Broadcom BCM7xxx internal transceivers support.
+ *
+ * Copyright (C) 2014, Broadcom Corporation
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version
+ * 2 of the License, or (at your option) any later version.
+ */
+
+#include <linux/module.h>
+#include <linux/phy.h>
+#include <linux/delay.h>
+#include <linux/bitops.h>
+#include <linux/brcmphy.h>
+
+/* Broadcom BCM7xxx internal PHY registers */
+#define MII_BCM7XXX_CHANNEL_WIDTH	0x2000
+
+/* 40nm only register definitions */
+#define MII_BCM7XXX_100TX_AUX_CTL	0x10
+#define MII_BCM7XXX_100TX_FALSE_CAR	0x13
+#define MII_BCM7XXX_100TX_DISC		0x14
+#define MII_BCM7XXX_AUX_MODE		0x1d
+#define  MII_BCM7XX_64CLK_MDIO		BIT(12)
+#define MII_BCM7XXX_CORE_BASE1E		0x1e
+#define MII_BCM7XXX_TEST		0x1f
+#define  MII_BCM7XXX_SHD_MODE_2		BIT(2)
+
+static int bcm7445_config_init(struct phy_device *phydev)
+{
+	int ret;
+	const struct bcm7445_regs {
+		int reg;
+		u16 value;
+	} bcm7445_regs_cfg[] = {
+		/* increases ADC latency by 24ns */
+		{ MII_BCM54XX_EXP_SEL, 0x0038 },
+		{ MII_BCM54XX_EXP_DATA, 0xAB95 },
+		/* increases internal 1V LDO voltage by 5% */
+		{ MII_BCM54XX_EXP_SEL, 0x2038 },
+		{ MII_BCM54XX_EXP_DATA, 0xBB22 },
+		/* reduce RX low pass filter corner frequency */
+		{ MII_BCM54XX_EXP_SEL, 0x6038 },
+		{ MII_BCM54XX_EXP_DATA, 0xFFC5 },
+		/* reduce RX high pass filter corner frequency */
+		{ MII_BCM54XX_EXP_SEL, 0x003a },
+		{ MII_BCM54XX_EXP_DATA, 0x2002 },
+	};
+	unsigned int i;
+
+	for (i = 0; i < ARRAY_SIZE(bcm7445_regs_cfg); i++) {
+		ret = phy_write(phydev,
+				bcm7445_regs_cfg[i].reg,
+				bcm7445_regs_cfg[i].value);
+		if (ret)
+			return ret;
+	}
+
+	return 0;
+}
+
+static void phy_write_exp(struct phy_device *phydev,
+					u16 reg, u16 value)
+{
+	phy_write(phydev, MII_BCM54XX_EXP_SEL, MII_BCM54XX_EXP_SEL_ER | reg);
+	phy_write(phydev, MII_BCM54XX_EXP_DATA, value);
+}
+
+static void phy_write_misc(struct phy_device *phydev,
+					u16 reg, u16 chl, u16 value)
+{
+	int tmp;
+
+	phy_write(phydev, MII_BCM54XX_AUX_CTL, MII_BCM54XX_AUXCTL_SHDWSEL_MISC);
+
+	tmp = phy_read(phydev, MII_BCM54XX_AUX_CTL);
+	tmp |= MII_BCM54XX_AUXCTL_ACTL_SMDSP_ENA;
+	phy_write(phydev, MII_BCM54XX_AUX_CTL, tmp);
+
+	tmp = (chl * MII_BCM7XXX_CHANNEL_WIDTH) | reg;
+	phy_write(phydev, MII_BCM54XX_EXP_SEL, tmp);
+
+	phy_write(phydev, MII_BCM54XX_EXP_DATA, value);
+}
+
+static int bcm7xxx_28nm_afe_config_init(struct phy_device *phydev)
+{
+	/* write AFE_RXCONFIG_0 */
+	phy_write_misc(phydev, 0x38, 0x0000, 0xeb19);
+
+	/* write AFE_RXCONFIG_1 */
+	phy_write_misc(phydev, 0x38, 0x0001, 0x9a3f);
+
+	/* write AFE_RX_LP_COUNTER */
+	phy_write_misc(phydev, 0x38, 0x0003, 0x7fc7);
+
+	/* write AFE_HPF_TRIM_OTHERS */
+	phy_write_misc(phydev, 0x3A, 0x0000, 0x000b);
+
+	/* write AFTE_TX_CONFIG */
+	phy_write_misc(phydev, 0x39, 0x0000, 0x0800);
+
+	/* Increase VCO range to prevent unlocking problem of PLL at low
+	 * temp
+	 */
+	phy_write_misc(phydev, 0x0032, 0x0001, 0x0048);
+
+	/* Change Ki to 011 */
+	phy_write_misc(phydev, 0x0032, 0x0002, 0x021b);
+
+	/* Disable loading of TVCO buffer to bandgap, set bandgap trim
+	 * to 111
+	 */
+	phy_write_misc(phydev, 0x0033, 0x0000, 0x0e20);
+
+	/* Adjust bias current trim by -3 */
+	phy_write_misc(phydev, 0x000a, 0x0000, 0x690b);
+
+	/* Switch to CORE_BASE1E */
+	phy_write(phydev, MII_BCM7XXX_CORE_BASE1E, 0xd);
+
+	/* Reset R_CAL/RC_CAL Engine */
+	phy_write_exp(phydev, 0x00b0, 0x0010);
+
+	/* Disable Reset R_CAL/RC_CAL Engine */
+	phy_write_exp(phydev, 0x00b0, 0x0000);
+
+	return 0;
+}
+
+static int bcm7xxx_28nm_config_init(struct phy_device *phydev)
+{
+	int ret;
+
+	ret = bcm7445_config_init(phydev);
+	if (ret)
+		return ret;
+
+	return bcm7xxx_28nm_afe_config_init(phydev);
+}
+
+static int phy_set_clr_bits(struct phy_device *dev, int location,
+					int set_mask, int clr_mask)
+{
+	int v, ret;
+
+	v = phy_read(dev, location);
+	if (v < 0)
+		return v;
+
+	v &= ~clr_mask;
+	v |= set_mask;
+
+	ret = phy_write(dev, location, v);
+	if (ret < 0)
+		return ret;
+
+	return v;
+}
+
+static int bcm7xxx_config_init(struct phy_device *phydev)
+{
+	int ret;
+
+	/* Enable 64 clock MDIO */
+	phy_write(phydev, MII_BCM7XXX_AUX_MODE, MII_BCM7XX_64CLK_MDIO);
+	phy_read(phydev, MII_BCM7XXX_AUX_MODE);
+
+	/* Workaround only required for 100Mbits/sec */
+	if (!(phydev->dev_flags & PHY_BRCM_100MBPS_WAR))
+		return 0;
+
+	/* set shadow mode 2 */
+	ret = phy_set_clr_bits(phydev, MII_BCM7XXX_TEST,
+			MII_BCM7XXX_SHD_MODE_2, MII_BCM7XXX_SHD_MODE_2);
+	if (ret < 0)
+		return ret;
+
+	/* set iddq_clkbias */
+	phy_write(phydev, MII_BCM7XXX_100TX_DISC, 0x0F00);
+	udelay(10);
+
+	/* reset iddq_clkbias */
+	phy_write(phydev, MII_BCM7XXX_100TX_DISC, 0x0C00);
+
+	phy_write(phydev, MII_BCM7XXX_100TX_FALSE_CAR, 0x7555);
+
+	/* reset shadow mode 2 */
+	ret = phy_set_clr_bits(phydev, MII_BCM7XXX_TEST, MII_BCM7XXX_SHD_MODE_2, 0);
+	if (ret < 0)
+		return ret;
+
+	return 0;
+}
+
+/* Workaround for putting the PHY in IDDQ mode, required
+ * for all BCM7XXX PHYs
+ */
+static int bcm7xxx_suspend(struct phy_device *phydev)
+{
+	int ret;
+	const struct bcm7xxx_regs {
+		int reg;
+		u16 value;
+	} bcm7xxx_suspend_cfg[] = {
+		{ MII_BCM7XXX_TEST, 0x008b },
+		{ MII_BCM7XXX_100TX_AUX_CTL, 0x01c0 },
+		{ MII_BCM7XXX_100TX_DISC, 0x7000 },
+		{ MII_BCM7XXX_TEST, 0x000f },
+		{ MII_BCM7XXX_100TX_AUX_CTL, 0x20d0 },
+		{ MII_BCM7XXX_TEST, 0x000b },
+	};
+	unsigned int i;
+
+	for (i = 0; i < ARRAY_SIZE(bcm7xxx_suspend_cfg); i++) {
+		ret = phy_write(phydev,
+				bcm7xxx_suspend_cfg[i].reg,
+				bcm7xxx_suspend_cfg[i].value);
+		if (ret)
+			return ret;
+	}
+
+	return 0;
+}
+
+static int bcm7xxx_dummy_config_init(struct phy_device *phydev)
+{
+	return 0;
+}
+
+static struct phy_driver bcm7xxx_driver[] = {
+{
+	.phy_id		= PHY_ID_BCM7366,
+	.phy_id_mask	= 0xfffffff0,
+	.name		= "Broadcom BCM7366",
+	.features	= PHY_GBIT_FEATURES |
+			  SUPPORTED_Pause | SUPPORTED_Asym_Pause,
+	.flags		= PHY_IS_INTERNAL,
+	.config_init	= bcm7xxx_28nm_afe_config_init,
+	.config_aneg	= genphy_config_aneg,
+	.read_status	= genphy_read_status,
+	.suspend	= bcm7xxx_suspend,
+	.resume		= bcm7xxx_28nm_afe_config_init,
+	.driver		= { .owner = THIS_MODULE },
+}, {
+	.phy_id		= PHY_ID_BCM7439,
+	.phy_id_mask	= 0xfffffff0,
+	.name		= "Broadcom BCM7439",
+	.features	= PHY_GBIT_FEATURES |
+			  SUPPORTED_Pause | SUPPORTED_Asym_Pause,
+	.flags		= PHY_IS_INTERNAL,
+	.config_init	= bcm7xxx_28nm_afe_config_init,
+	.config_aneg	= genphy_config_aneg,
+	.read_status	= genphy_read_status,
+	.suspend	= bcm7xxx_suspend,
+	.resume		= bcm7xxx_28nm_afe_config_init,
+	.driver		= { .owner = THIS_MODULE },
+}, {
+	.phy_id		= PHY_ID_BCM7445,
+	.phy_id_mask	= 0xfffffff0,
+	.name		= "Broadcom BCM7445",
+	.features	= PHY_GBIT_FEATURES |
+			  SUPPORTED_Pause | SUPPORTED_Asym_Pause,
+	.flags		= PHY_IS_INTERNAL,
+	.config_init	= bcm7xxx_28nm_config_init,
+	.config_aneg	= genphy_config_aneg,
+	.read_status	= genphy_read_status,
+	.suspend	= bcm7xxx_suspend,
+	.resume		= bcm7xxx_28nm_config_init,
+	.driver		= { .owner = THIS_MODULE },
+}, {
+	.name		= "Broadcom BCM7XXX 28nm",
+	.phy_id		= PHY_ID_BCM7XXX_28,
+	.phy_id_mask	= PHY_BCM_OUI_MASK,
+	.features	= PHY_GBIT_FEATURES |
+			  SUPPORTED_Pause | SUPPORTED_Asym_Pause,
+	.flags		= PHY_IS_INTERNAL,
+	.config_init	= bcm7xxx_28nm_config_init,
+	.config_aneg	= genphy_config_aneg,
+	.read_status	= genphy_read_status,
+	.suspend	= bcm7xxx_suspend,
+	.resume		= bcm7xxx_28nm_config_init,
+	.driver		= { .owner = THIS_MODULE },
+}, {
+	.phy_id		= PHY_BCM_OUI_4,
+	.phy_id_mask	= 0xffff0000,
+	.name		= "Broadcom BCM7XXX 40nm",
+	.features	= PHY_GBIT_FEATURES |
+			  SUPPORTED_Pause | SUPPORTED_Asym_Pause,
+	.flags		= PHY_IS_INTERNAL,
+	.config_init	= bcm7xxx_config_init,
+	.config_aneg	= genphy_config_aneg,
+	.read_status	= genphy_read_status,
+	.suspend	= bcm7xxx_suspend,
+	.resume		= bcm7xxx_config_init,
+	.driver		= { .owner = THIS_MODULE },
+}, {
+	.phy_id		= PHY_BCM_OUI_5,
+	.phy_id_mask	= 0xffffff00,
+	.name		= "Broadcom BCM7XXX 65nm",
+	.features	= PHY_BASIC_FEATURES |
+			  SUPPORTED_Pause | SUPPORTED_Asym_Pause,
+	.flags		= PHY_IS_INTERNAL,
+	.config_init	= bcm7xxx_dummy_config_init,
+	.config_aneg	= genphy_config_aneg,
+	.read_status	= genphy_read_status,
+	.suspend	= bcm7xxx_suspend,
+	.resume		= bcm7xxx_config_init,
+	.driver		= { .owner = THIS_MODULE },
+} };
+
+static struct mdio_device_id __maybe_unused bcm7xxx_tbl[] = {
+	{ PHY_ID_BCM7366, 0xfffffff0, },
+	{ PHY_ID_BCM7439, 0xfffffff0, },
+	{ PHY_ID_BCM7445, 0xfffffff0, },
+	{ PHY_ID_BCM7XXX_28, 0xfffffc00 },
+	{ PHY_BCM_OUI_4, 0xffff0000 },
+	{ PHY_BCM_OUI_5, 0xffffff00 },
+	{ }
+};
+
+static int __init bcm7xxx_phy_init(void)
+{
+	return phy_drivers_register(bcm7xxx_driver,
+			ARRAY_SIZE(bcm7xxx_driver));
+}
+
+static void __exit bcm7xxx_phy_exit(void)
+{
+	phy_drivers_unregister(bcm7xxx_driver,
+			ARRAY_SIZE(bcm7xxx_driver));
+}
+
+module_init(bcm7xxx_phy_init);
+module_exit(bcm7xxx_phy_exit);
+
+MODULE_DEVICE_TABLE(mdio, bcm7xxx_tbl);
+
+MODULE_DESCRIPTION("Broadcom BCM7xxx internal PHY driver");
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Broadcom Corporation");