Merge branch 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx: (21 commits)
dmaengine: add slave-dma maintainer
dma: ipu_idmac: do not lose valid received data in the irq handler
dmaengine: imx-sdma: fix up param for the last BD in sdma_prep_slave_sg()
dmaengine: imx-sdma: correct sdmac->status in sdma_handle_channel_loop()
dmaengine: imx-sdma: return sdmac->status in sdma_tx_status()
dmaengine: imx-sdma: set sdmac->status to DMA_ERROR in err_out of sdma_prep_slave_sg()
dmaengine: imx-sdma: remove IMX_DMA_SG_LOOP handling in sdma_prep_slave_sg()
dmaengine i.MX dma: initialize dma capabilities outside channel loop
dmaengine i.MX DMA: do not initialize chan_id field
dmaengine i.MX dma: check sg entries for valid addresses and lengths
dmaengine i.MX dma: set maximum segment size for our device
dmaengine i.MX SDMA: reserve channel 0 by not registering it
dmaengine i.MX SDMA: initialize dma capabilities outside channel loop
dmaengine i.MX SDMA: do not initialize chan_id field
dmaengine i.MX sdma: check sg entries for valid addresses and lengths
dmaengine i.MX sdma: set maximum segment size for our device
DMA: PL08x: fix channel pausing to timeout rather than lockup
DMA: PL08x: fix infinite wait when terminating transfers
dmaengine: imx-sdma: fix inconsistent naming in sdma_assign_cookie()
dmaengine: imx-sdma: propagate error in sdma_probe() instead of returning 0
...
diff --git a/MAINTAINERS b/MAINTAINERS
index 4837907..5dd6c75 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -2126,6 +2126,7 @@
F: fs/dlm/
DMA GENERIC OFFLOAD ENGINE SUBSYSTEM
+M: Vinod Koul <vinod.koul@intel.com>
M: Dan Williams <dan.j.williams@intel.com>
S: Supported
F: drivers/dma/
diff --git a/drivers/dma/amba-pl08x.c b/drivers/dma/amba-pl08x.c
index 297f48b..07bca49 100644
--- a/drivers/dma/amba-pl08x.c
+++ b/drivers/dma/amba-pl08x.c
@@ -79,6 +79,7 @@
#include <linux/module.h>
#include <linux/interrupt.h>
#include <linux/slab.h>
+#include <linux/delay.h>
#include <linux/dmapool.h>
#include <linux/dmaengine.h>
#include <linux/amba/bus.h>
@@ -235,16 +236,19 @@
}
/*
- * Overall DMAC remains enabled always.
+ * Pause the channel by setting the HALT bit.
*
- * Disabling individual channels could lose data.
+ * For M->P transfers, pause the DMAC first and then stop the peripheral -
+ * the FIFO can only drain if the peripheral is still requesting data.
+ * (note: this can still timeout if the DMAC FIFO never drains of data.)
*
- * Disable the peripheral DMA after disabling the DMAC in order to allow
- * the DMAC FIFO to drain, and hence allow the channel to show inactive
+ * For P->M transfers, disable the peripheral first to stop it filling
+ * the DMAC FIFO, and then pause the DMAC.
*/
static void pl08x_pause_phy_chan(struct pl08x_phy_chan *ch)
{
u32 val;
+ int timeout;
/* Set the HALT bit and wait for the FIFO to drain */
val = readl(ch->base + PL080_CH_CONFIG);
@@ -252,8 +256,13 @@
writel(val, ch->base + PL080_CH_CONFIG);
/* Wait for channel inactive */
- while (pl08x_phy_channel_busy(ch))
- cpu_relax();
+ for (timeout = 1000; timeout; timeout--) {
+ if (!pl08x_phy_channel_busy(ch))
+ break;
+ udelay(1);
+ }
+ if (pl08x_phy_channel_busy(ch))
+ pr_err("pl08x: channel%u timeout waiting for pause\n", ch->id);
}
static void pl08x_resume_phy_chan(struct pl08x_phy_chan *ch)
@@ -267,19 +276,24 @@
}
-/* Stops the channel */
-static void pl08x_stop_phy_chan(struct pl08x_phy_chan *ch)
+/*
+ * pl08x_terminate_phy_chan() stops the channel, clears the FIFO and
+ * clears any pending interrupt status. This should not be used for
+ * an on-going transfer, but as a method of shutting down a channel
+ * (eg, when it's no longer used) or terminating a transfer.
+ */
+static void pl08x_terminate_phy_chan(struct pl08x_driver_data *pl08x,
+ struct pl08x_phy_chan *ch)
{
- u32 val;
+ u32 val = readl(ch->base + PL080_CH_CONFIG);
- pl08x_pause_phy_chan(ch);
+ val &= ~(PL080_CONFIG_ENABLE | PL080_CONFIG_ERR_IRQ_MASK |
+ PL080_CONFIG_TC_IRQ_MASK);
- /* Disable channel */
- val = readl(ch->base + PL080_CH_CONFIG);
- val &= ~PL080_CONFIG_ENABLE;
- val &= ~PL080_CONFIG_ERR_IRQ_MASK;
- val &= ~PL080_CONFIG_TC_IRQ_MASK;
writel(val, ch->base + PL080_CH_CONFIG);
+
+ writel(1 << ch->id, pl08x->base + PL080_ERR_CLEAR);
+ writel(1 << ch->id, pl08x->base + PL080_TC_CLEAR);
}
static inline u32 get_bytes_in_cctl(u32 cctl)
@@ -404,13 +418,12 @@
{
unsigned long flags;
+ spin_lock_irqsave(&ch->lock, flags);
+
/* Stop the channel and clear its interrupts */
- pl08x_stop_phy_chan(ch);
- writel((1 << ch->id), pl08x->base + PL080_ERR_CLEAR);
- writel((1 << ch->id), pl08x->base + PL080_TC_CLEAR);
+ pl08x_terminate_phy_chan(pl08x, ch);
/* Mark it as free */
- spin_lock_irqsave(&ch->lock, flags);
ch->serving = NULL;
spin_unlock_irqrestore(&ch->lock, flags);
}
@@ -1449,7 +1462,7 @@
plchan->state = PL08X_CHAN_IDLE;
if (plchan->phychan) {
- pl08x_stop_phy_chan(plchan->phychan);
+ pl08x_terminate_phy_chan(pl08x, plchan->phychan);
/*
* Mark physical channel as free and free any slave
diff --git a/drivers/dma/imx-dma.c b/drivers/dma/imx-dma.c
index e53d438..e18eaab 100644
--- a/drivers/dma/imx-dma.c
+++ b/drivers/dma/imx-dma.c
@@ -49,6 +49,7 @@
struct imxdma_engine {
struct device *dev;
+ struct device_dma_parameters dma_parms;
struct dma_device dma_device;
struct imxdma_channel channel[MAX_DMA_CHANNELS];
};
@@ -242,6 +243,21 @@
else
dmamode = DMA_MODE_WRITE;
+ switch (imxdmac->word_size) {
+ case DMA_SLAVE_BUSWIDTH_4_BYTES:
+ if (sgl->length & 3 || sgl->dma_address & 3)
+ return NULL;
+ break;
+ case DMA_SLAVE_BUSWIDTH_2_BYTES:
+ if (sgl->length & 1 || sgl->dma_address & 1)
+ return NULL;
+ break;
+ case DMA_SLAVE_BUSWIDTH_1_BYTE:
+ break;
+ default:
+ return NULL;
+ }
+
ret = imx_dma_setup_sg(imxdmac->imxdma_channel, sgl, sg_len,
dma_length, imxdmac->per_address, dmamode);
if (ret)
@@ -329,6 +345,9 @@
INIT_LIST_HEAD(&imxdma->dma_device.channels);
+ dma_cap_set(DMA_SLAVE, imxdma->dma_device.cap_mask);
+ dma_cap_set(DMA_CYCLIC, imxdma->dma_device.cap_mask);
+
/* Initialize channel parameters */
for (i = 0; i < MAX_DMA_CHANNELS; i++) {
struct imxdma_channel *imxdmac = &imxdma->channel[i];
@@ -346,11 +365,7 @@
imxdmac->imxdma = imxdma;
spin_lock_init(&imxdmac->lock);
- dma_cap_set(DMA_SLAVE, imxdma->dma_device.cap_mask);
- dma_cap_set(DMA_CYCLIC, imxdma->dma_device.cap_mask);
-
imxdmac->chan.device = &imxdma->dma_device;
- imxdmac->chan.chan_id = i;
imxdmac->channel = i;
/* Add the channel to the DMAC list */
@@ -370,6 +385,9 @@
platform_set_drvdata(pdev, imxdma);
+ imxdma->dma_device.dev->dma_parms = &imxdma->dma_parms;
+ dma_set_max_seg_size(imxdma->dma_device.dev, 0xffffff);
+
ret = dma_async_device_register(&imxdma->dma_device);
if (ret) {
dev_err(&pdev->dev, "unable to register\n");
diff --git a/drivers/dma/imx-sdma.c b/drivers/dma/imx-sdma.c
index d5a5d4d..b6d1455 100644
--- a/drivers/dma/imx-sdma.c
+++ b/drivers/dma/imx-sdma.c
@@ -230,7 +230,7 @@
* struct sdma_channel - housekeeping for a SDMA channel
*
* @sdma pointer to the SDMA engine for this channel
- * @channel the channel number, matches dmaengine chan_id
+ * @channel the channel number, matches dmaengine chan_id + 1
* @direction transfer type. Needed for setting SDMA script
* @peripheral_type Peripheral type. Needed for setting SDMA script
* @event_id0 aka dma request line
@@ -301,6 +301,7 @@
struct sdma_engine {
struct device *dev;
+ struct device_dma_parameters dma_parms;
struct sdma_channel channel[MAX_DMA_CHANNELS];
struct sdma_channel_control *channel_control;
void __iomem *regs;
@@ -449,7 +450,7 @@
if (bd->mode.status & BD_RROR)
sdmac->status = DMA_ERROR;
else
- sdmac->status = DMA_SUCCESS;
+ sdmac->status = DMA_IN_PROGRESS;
bd->mode.status |= BD_DONE;
sdmac->buf_tail++;
@@ -770,15 +771,15 @@
__raw_writel(1 << channel, sdma->regs + SDMA_H_START);
}
-static dma_cookie_t sdma_assign_cookie(struct sdma_channel *sdma)
+static dma_cookie_t sdma_assign_cookie(struct sdma_channel *sdmac)
{
- dma_cookie_t cookie = sdma->chan.cookie;
+ dma_cookie_t cookie = sdmac->chan.cookie;
if (++cookie < 0)
cookie = 1;
- sdma->chan.cookie = cookie;
- sdma->desc.cookie = cookie;
+ sdmac->chan.cookie = cookie;
+ sdmac->desc.cookie = cookie;
return cookie;
}
@@ -798,7 +799,7 @@
cookie = sdma_assign_cookie(sdmac);
- sdma_enable_channel(sdma, tx->chan->chan_id);
+ sdma_enable_channel(sdma, sdmac->channel);
spin_unlock_irq(&sdmac->lock);
@@ -811,10 +812,6 @@
struct imx_dma_data *data = chan->private;
int prio, ret;
- /* No need to execute this for internal channel 0 */
- if (chan->chan_id == 0)
- return 0;
-
if (!data)
return -EINVAL;
@@ -879,7 +876,7 @@
struct sdma_channel *sdmac = to_sdma_chan(chan);
struct sdma_engine *sdma = sdmac->sdma;
int ret, i, count;
- int channel = chan->chan_id;
+ int channel = sdmac->channel;
struct scatterlist *sg;
if (sdmac->status == DMA_IN_PROGRESS)
@@ -924,22 +921,33 @@
ret = -EINVAL;
goto err_out;
}
- if (sdmac->word_size == DMA_SLAVE_BUSWIDTH_4_BYTES)
+
+ switch (sdmac->word_size) {
+ case DMA_SLAVE_BUSWIDTH_4_BYTES:
bd->mode.command = 0;
- else
- bd->mode.command = sdmac->word_size;
+ if (count & 3 || sg->dma_address & 3)
+ return NULL;
+ break;
+ case DMA_SLAVE_BUSWIDTH_2_BYTES:
+ bd->mode.command = 2;
+ if (count & 1 || sg->dma_address & 1)
+ return NULL;
+ break;
+ case DMA_SLAVE_BUSWIDTH_1_BYTE:
+ bd->mode.command = 1;
+ break;
+ default:
+ return NULL;
+ }
param = BD_DONE | BD_EXTD | BD_CONT;
- if (sdmac->flags & IMX_DMA_SG_LOOP) {
+ if (i + 1 == sg_len) {
param |= BD_INTR;
- if (i + 1 == sg_len)
- param |= BD_WRAP;
+ param |= BD_LAST;
+ param &= ~BD_CONT;
}
- if (i + 1 == sg_len)
- param |= BD_INTR;
-
dev_dbg(sdma->dev, "entry %d: count: %d dma: 0x%08x %s%s\n",
i, count, sg->dma_address,
param & BD_WRAP ? "wrap" : "",
@@ -953,6 +961,7 @@
return &sdmac->desc;
err_out:
+ sdmac->status = DMA_ERROR;
return NULL;
}
@@ -963,7 +972,7 @@
struct sdma_channel *sdmac = to_sdma_chan(chan);
struct sdma_engine *sdma = sdmac->sdma;
int num_periods = buf_len / period_len;
- int channel = chan->chan_id;
+ int channel = sdmac->channel;
int ret, i = 0, buf = 0;
dev_dbg(sdma->dev, "%s channel: %d\n", __func__, channel);
@@ -1066,14 +1075,12 @@
{
struct sdma_channel *sdmac = to_sdma_chan(chan);
dma_cookie_t last_used;
- enum dma_status ret;
last_used = chan->cookie;
- ret = dma_async_is_complete(cookie, sdmac->last_completed, last_used);
dma_set_tx_state(txstate, sdmac->last_completed, last_used, 0);
- return ret;
+ return sdmac->status;
}
static void sdma_issue_pending(struct dma_chan *chan)
@@ -1135,7 +1142,7 @@
/* download the RAM image for SDMA */
sdma_load_script(sdma, ram_code,
header->ram_code_size,
- sdma->script_addrs->ram_code_start_addr);
+ addr->ram_code_start_addr);
clk_disable(sdma->clk);
sdma_add_scripts(sdma, addr);
@@ -1237,7 +1244,6 @@
struct resource *iores;
struct sdma_platform_data *pdata = pdev->dev.platform_data;
int i;
- dma_cap_mask_t mask;
struct sdma_engine *sdma;
sdma = kzalloc(sizeof(*sdma), GFP_KERNEL);
@@ -1280,6 +1286,9 @@
sdma->version = pdata->sdma_version;
+ dma_cap_set(DMA_SLAVE, sdma->dma_device.cap_mask);
+ dma_cap_set(DMA_CYCLIC, sdma->dma_device.cap_mask);
+
INIT_LIST_HEAD(&sdma->dma_device.channels);
/* Initialize channel parameters */
for (i = 0; i < MAX_DMA_CHANNELS; i++) {
@@ -1288,15 +1297,17 @@
sdmac->sdma = sdma;
spin_lock_init(&sdmac->lock);
- dma_cap_set(DMA_SLAVE, sdma->dma_device.cap_mask);
- dma_cap_set(DMA_CYCLIC, sdma->dma_device.cap_mask);
-
sdmac->chan.device = &sdma->dma_device;
- sdmac->chan.chan_id = i;
sdmac->channel = i;
- /* Add the channel to the DMAC list */
- list_add_tail(&sdmac->chan.device_node, &sdma->dma_device.channels);
+ /*
+ * Add the channel to the DMAC list. Do not add channel 0 though
+ * because we need it internally in the SDMA driver. This also means
+ * that channel 0 in dmaengine counting matches sdma channel 1.
+ */
+ if (i)
+ list_add_tail(&sdmac->chan.device_node,
+ &sdma->dma_device.channels);
}
ret = sdma_init(sdma);
@@ -1317,6 +1328,8 @@
sdma->dma_device.device_prep_dma_cyclic = sdma_prep_dma_cyclic;
sdma->dma_device.device_control = sdma_control;
sdma->dma_device.device_issue_pending = sdma_issue_pending;
+ sdma->dma_device.dev->dma_parms = &sdma->dma_parms;
+ dma_set_max_seg_size(sdma->dma_device.dev, 65535);
ret = dma_async_device_register(&sdma->dma_device);
if (ret) {
@@ -1324,13 +1337,6 @@
goto err_init;
}
- /* request channel 0. This is an internal control channel
- * to the SDMA engine and not available to clients.
- */
- dma_cap_zero(mask);
- dma_cap_set(DMA_SLAVE, mask);
- dma_request_channel(mask, NULL, NULL);
-
dev_info(sdma->dev, "initialized\n");
return 0;
@@ -1348,7 +1354,7 @@
err_request_region:
err_irq:
kfree(sdma);
- return 0;
+ return ret;
}
static int __exit sdma_remove(struct platform_device *pdev)
diff --git a/drivers/dma/ipu/ipu_idmac.c b/drivers/dma/ipu/ipu_idmac.c
index cb26ee9..c1a125e7 100644
--- a/drivers/dma/ipu/ipu_idmac.c
+++ b/drivers/dma/ipu/ipu_idmac.c
@@ -1145,29 +1145,6 @@
reg = idmac_read_icreg(ipu, IDMAC_CHA_EN);
idmac_write_icreg(ipu, reg & ~chan_mask, IDMAC_CHA_EN);
- /*
- * Problem (observed with channel DMAIC_7): after enabling the channel
- * and initialising buffers, there comes an interrupt with current still
- * pointing at buffer 0, whereas it should use buffer 0 first and only
- * generate an interrupt when it is done, then current should already
- * point to buffer 1. This spurious interrupt also comes on channel
- * DMASDC_0. With DMAIC_7 normally, is we just leave the ISR after the
- * first interrupt, there comes the second with current correctly
- * pointing to buffer 1 this time. But sometimes this second interrupt
- * doesn't come and the channel hangs. Clearing BUFx_RDY when disabling
- * the channel seems to prevent the channel from hanging, but it doesn't
- * prevent the spurious interrupt. This might also be unsafe. Think
- * about the IDMAC controller trying to switch to a buffer, when we
- * clear the ready bit, and re-enable it a moment later.
- */
- reg = idmac_read_ipureg(ipu, IPU_CHA_BUF0_RDY);
- idmac_write_ipureg(ipu, 0, IPU_CHA_BUF0_RDY);
- idmac_write_ipureg(ipu, reg & ~(1UL << channel), IPU_CHA_BUF0_RDY);
-
- reg = idmac_read_ipureg(ipu, IPU_CHA_BUF1_RDY);
- idmac_write_ipureg(ipu, 0, IPU_CHA_BUF1_RDY);
- idmac_write_ipureg(ipu, reg & ~(1UL << channel), IPU_CHA_BUF1_RDY);
-
spin_unlock_irqrestore(&ipu->lock, flags);
return 0;
@@ -1246,33 +1223,6 @@
/* Other interrupts do not interfere with this channel */
spin_lock(&ichan->lock);
- if (unlikely(chan_id != IDMAC_SDC_0 && chan_id != IDMAC_SDC_1 &&
- ((curbuf >> chan_id) & 1) == ichan->active_buffer &&
- !list_is_last(ichan->queue.next, &ichan->queue))) {
- int i = 100;
-
- /* This doesn't help. See comment in ipu_disable_channel() */
- while (--i) {
- curbuf = idmac_read_ipureg(&ipu_data, IPU_CHA_CUR_BUF);
- if (((curbuf >> chan_id) & 1) != ichan->active_buffer)
- break;
- cpu_relax();
- }
-
- if (!i) {
- spin_unlock(&ichan->lock);
- dev_dbg(dev,
- "IRQ on active buffer on channel %x, active "
- "%d, ready %x, %x, current %x!\n", chan_id,
- ichan->active_buffer, ready0, ready1, curbuf);
- return IRQ_NONE;
- } else
- dev_dbg(dev,
- "Buffer deactivated on channel %x, active "
- "%d, ready %x, %x, current %x, rest %d!\n", chan_id,
- ichan->active_buffer, ready0, ready1, curbuf, i);
- }
-
if (unlikely((ichan->active_buffer && (ready1 >> chan_id) & 1) ||
(!ichan->active_buffer && (ready0 >> chan_id) & 1)
)) {