// SPDX-License-Identifier: GPL-2.0-or-later
/*
 *
 *  Generic Bluetooth USB driver
 *
 *  Copyright (C) 2005-2008  Marcel Holtmann <marcel@holtmann.org>
 */

#include <linux/dmi.h>
#include <linux/module.h>
#include <linux/usb.h>
#include <linux/usb/quirks.h>
#include <linux/firmware.h>
#include <linux/iopoll.h>
#include <linux/of_device.h>
#include <linux/of_irq.h>
#include <linux/suspend.h>
#include <linux/gpio/consumer.h>
#include <asm/unaligned.h>

#include <net/bluetooth/bluetooth.h>
#include <net/bluetooth/hci_core.h>

#include "btintel.h"
#include "btbcm.h"
#include "btrtl.h"

#define VERSION "0.8"

static bool disable_scofix;
static bool force_scofix;
static bool enable_autosuspend = IS_ENABLED(CONFIG_BT_HCIBTUSB_AUTOSUSPEND);

static bool reset = true;

static struct usb_driver btusb_driver;

#define BTUSB_IGNORE		0x01
#define BTUSB_DIGIANSWER	0x02
#define BTUSB_CSR		0x04
#define BTUSB_SNIFFER		0x08
#define BTUSB_BCM92035		0x10
#define BTUSB_BROKEN_ISOC	0x20
#define BTUSB_WRONG_SCO_MTU	0x40
#define BTUSB_ATH3012		0x80
#define BTUSB_INTEL		0x100
#define BTUSB_INTEL_BOOT	0x200
#define BTUSB_BCM_PATCHRAM	0x400
#define BTUSB_MARVELL		0x800
#define BTUSB_SWAVE		0x1000
#define BTUSB_INTEL_NEW		0x2000
#define BTUSB_AMP		0x4000
#define BTUSB_QCA_ROME		0x8000
#define BTUSB_BCM_APPLE		0x10000
#define BTUSB_REALTEK		0x20000
#define BTUSB_BCM2045		0x40000
#define BTUSB_IFNUM_2		0x80000
#define BTUSB_CW6622		0x100000
#define BTUSB_MEDIATEK		0x200000
#define BTUSB_WIDEBAND_SPEECH	0x400000
#define BTUSB_VALID_LE_STATES   0x800000
#define BTUSB_QCA_WCN6855	0x1000000
#define BTUSB_INTEL_NEWGEN	0x2000000

static const struct usb_device_id btusb_table[] = {
	/* Generic Bluetooth USB device */
	{ USB_DEVICE_INFO(0xe0, 0x01, 0x01) },

	/* Generic Bluetooth AMP device */
	{ USB_DEVICE_INFO(0xe0, 0x01, 0x04), .driver_info = BTUSB_AMP },

	/* Generic Bluetooth USB interface */
	{ USB_INTERFACE_INFO(0xe0, 0x01, 0x01) },

	/* Apple-specific (Broadcom) devices */
	{ USB_VENDOR_AND_INTERFACE_INFO(0x05ac, 0xff, 0x01, 0x01),
	  .driver_info = BTUSB_BCM_APPLE | BTUSB_IFNUM_2 },

	/* MediaTek MT76x0E */
	{ USB_DEVICE(0x0e8d, 0x763f) },

	/* Broadcom SoftSailing reporting vendor specific */
	{ USB_DEVICE(0x0a5c, 0x21e1) },

	/* Apple MacBookPro 7,1 */
	{ USB_DEVICE(0x05ac, 0x8213) },

	/* Apple iMac11,1 */
	{ USB_DEVICE(0x05ac, 0x8215) },

	/* Apple MacBookPro6,2 */
	{ USB_DEVICE(0x05ac, 0x8218) },

	/* Apple MacBookAir3,1, MacBookAir3,2 */
	{ USB_DEVICE(0x05ac, 0x821b) },

	/* Apple MacBookAir4,1 */
	{ USB_DEVICE(0x05ac, 0x821f) },

	/* Apple MacBookPro8,2 */
	{ USB_DEVICE(0x05ac, 0x821a) },

	/* Apple MacMini5,1 */
	{ USB_DEVICE(0x05ac, 0x8281) },

	/* AVM BlueFRITZ! USB v2.0 */
	{ USB_DEVICE(0x057c, 0x3800), .driver_info = BTUSB_SWAVE },

	/* Bluetooth Ultraport Module from IBM */
	{ USB_DEVICE(0x04bf, 0x030a) },

	/* ALPS Modules with non-standard id */
	{ USB_DEVICE(0x044e, 0x3001) },
	{ USB_DEVICE(0x044e, 0x3002) },

	/* Ericsson with non-standard id */
	{ USB_DEVICE(0x0bdb, 0x1002) },

	/* Canyon CN-BTU1 with HID interfaces */
	{ USB_DEVICE(0x0c10, 0x0000) },

	/* Broadcom BCM20702A0 */
	{ USB_DEVICE(0x413c, 0x8197) },

	/* Broadcom BCM20702B0 (Dynex/Insignia) */
	{ USB_DEVICE(0x19ff, 0x0239), .driver_info = BTUSB_BCM_PATCHRAM },

	/* Broadcom BCM43142A0 (Foxconn/Lenovo) */
	{ USB_VENDOR_AND_INTERFACE_INFO(0x105b, 0xff, 0x01, 0x01),
	  .driver_info = BTUSB_BCM_PATCHRAM },

	/* Broadcom BCM920703 (HTC Vive) */
	{ USB_VENDOR_AND_INTERFACE_INFO(0x0bb4, 0xff, 0x01, 0x01),
	  .driver_info = BTUSB_BCM_PATCHRAM },

	/* Foxconn - Hon Hai */
	{ USB_VENDOR_AND_INTERFACE_INFO(0x0489, 0xff, 0x01, 0x01),
	  .driver_info = BTUSB_BCM_PATCHRAM },

	/* Lite-On Technology - Broadcom based */
	{ USB_VENDOR_AND_INTERFACE_INFO(0x04ca, 0xff, 0x01, 0x01),
	  .driver_info = BTUSB_BCM_PATCHRAM },

	/* Broadcom devices with vendor specific id */
	{ USB_VENDOR_AND_INTERFACE_INFO(0x0a5c, 0xff, 0x01, 0x01),
	  .driver_info = BTUSB_BCM_PATCHRAM },

	/* ASUSTek Computer - Broadcom based */
	{ USB_VENDOR_AND_INTERFACE_INFO(0x0b05, 0xff, 0x01, 0x01),
	  .driver_info = BTUSB_BCM_PATCHRAM },

	/* Belkin F8065bf - Broadcom based */
	{ USB_VENDOR_AND_INTERFACE_INFO(0x050d, 0xff, 0x01, 0x01),
	  .driver_info = BTUSB_BCM_PATCHRAM },

	/* IMC Networks - Broadcom based */
	{ USB_VENDOR_AND_INTERFACE_INFO(0x13d3, 0xff, 0x01, 0x01),
	  .driver_info = BTUSB_BCM_PATCHRAM },

	/* Dell Computer - Broadcom based  */
	{ USB_VENDOR_AND_INTERFACE_INFO(0x413c, 0xff, 0x01, 0x01),
	  .driver_info = BTUSB_BCM_PATCHRAM },

	/* Toshiba Corp - Broadcom based */
	{ USB_VENDOR_AND_INTERFACE_INFO(0x0930, 0xff, 0x01, 0x01),
	  .driver_info = BTUSB_BCM_PATCHRAM },

	/* Intel Bluetooth USB Bootloader (RAM module) */
	{ USB_DEVICE(0x8087, 0x0a5a),
	  .driver_info = BTUSB_INTEL_BOOT | BTUSB_BROKEN_ISOC },

	{ }	/* Terminating entry */
};

MODULE_DEVICE_TABLE(usb, btusb_table);

static const struct usb_device_id blacklist_table[] = {
	/* CSR BlueCore devices */
	{ USB_DEVICE(0x0a12, 0x0001), .driver_info = BTUSB_CSR },

	/* Broadcom BCM2033 without firmware */
	{ USB_DEVICE(0x0a5c, 0x2033), .driver_info = BTUSB_IGNORE },

	/* Broadcom BCM2045 devices */
	{ USB_DEVICE(0x0a5c, 0x2045), .driver_info = BTUSB_BCM2045 },

	/* Atheros 3011 with sflash firmware */
	{ USB_DEVICE(0x0489, 0xe027), .driver_info = BTUSB_IGNORE },
	{ USB_DEVICE(0x0489, 0xe03d), .driver_info = BTUSB_IGNORE },
	{ USB_DEVICE(0x04f2, 0xaff1), .driver_info = BTUSB_IGNORE },
	{ USB_DEVICE(0x0930, 0x0215), .driver_info = BTUSB_IGNORE },
	{ USB_DEVICE(0x0cf3, 0x3002), .driver_info = BTUSB_IGNORE },
	{ USB_DEVICE(0x0cf3, 0xe019), .driver_info = BTUSB_IGNORE },
	{ USB_DEVICE(0x13d3, 0x3304), .driver_info = BTUSB_IGNORE },

	/* Atheros AR9285 Malbec with sflash firmware */
	{ USB_DEVICE(0x03f0, 0x311d), .driver_info = BTUSB_IGNORE },

	/* Atheros 3012 with sflash firmware */
	{ USB_DEVICE(0x0489, 0xe04d), .driver_info = BTUSB_ATH3012 },
	{ USB_DEVICE(0x0489, 0xe04e), .driver_info = BTUSB_ATH3012 },
	{ USB_DEVICE(0x0489, 0xe056), .driver_info = BTUSB_ATH3012 },
	{ USB_DEVICE(0x0489, 0xe057), .driver_info = BTUSB_ATH3012 },
	{ USB_DEVICE(0x0489, 0xe05f), .driver_info = BTUSB_ATH3012 },
	{ USB_DEVICE(0x0489, 0xe076), .driver_info = BTUSB_ATH3012 },
	{ USB_DEVICE(0x0489, 0xe078), .driver_info = BTUSB_ATH3012 },
	{ USB_DEVICE(0x0489, 0xe095), .driver_info = BTUSB_ATH3012 },
	{ USB_DEVICE(0x04c5, 0x1330), .driver_info = BTUSB_ATH3012 },
	{ USB_DEVICE(0x04ca, 0x3004), .driver_info = BTUSB_ATH3012 },
	{ USB_DEVICE(0x04ca, 0x3005), .driver_info = BTUSB_ATH3012 },
	{ USB_DEVICE(0x04ca, 0x3006), .driver_info = BTUSB_ATH3012 },
	{ USB_DEVICE(0x04ca, 0x3007), .driver_info = BTUSB_ATH3012 },
	{ USB_DEVICE(0x04ca, 0x3008), .driver_info = BTUSB_ATH3012 },
	{ USB_DEVICE(0x04ca, 0x300b), .driver_info = BTUSB_ATH3012 },
	{ USB_DEVICE(0x04ca, 0x300d), .driver_info = BTUSB_ATH3012 },
	{ USB_DEVICE(0x04ca, 0x300f), .driver_info = BTUSB_ATH3012 },
	{ USB_DEVICE(0x04ca, 0x3010), .driver_info = BTUSB_ATH3012 },
	{ USB_DEVICE(0x04ca, 0x3014), .driver_info = BTUSB_ATH3012 },
	{ USB_DEVICE(0x04ca, 0x3018), .driver_info = BTUSB_ATH3012 },
	{ USB_DEVICE(0x0930, 0x0219), .driver_info = BTUSB_ATH3012 },
	{ USB_DEVICE(0x0930, 0x021c), .driver_info = BTUSB_ATH3012 },
	{ USB_DEVICE(0x0930, 0x0220), .driver_info = BTUSB_ATH3012 },
	{ USB_DEVICE(0x0930, 0x0227), .driver_info = BTUSB_ATH3012 },
	{ USB_DEVICE(0x0b05, 0x17d0), .driver_info = BTUSB_ATH3012 },
	{ USB_DEVICE(0x0cf3, 0x0036), .driver_info = BTUSB_ATH3012 },
	{ USB_DEVICE(0x0cf3, 0x3004), .driver_info = BTUSB_ATH3012 },
	{ USB_DEVICE(0x0cf3, 0x3008), .driver_info = BTUSB_ATH3012 },
	{ USB_DEVICE(0x0cf3, 0x311d), .driver_info = BTUSB_ATH3012 },
	{ USB_DEVICE(0x0cf3, 0x311e), .driver_info = BTUSB_ATH3012 },
	{ USB_DEVICE(0x0cf3, 0x311f), .driver_info = BTUSB_ATH3012 },
	{ USB_DEVICE(0x0cf3, 0x3121), .driver_info = BTUSB_ATH3012 },
	{ USB_DEVICE(0x0cf3, 0x817a), .driver_info = BTUSB_ATH3012 },
	{ USB_DEVICE(0x0cf3, 0x817b), .driver_info = BTUSB_ATH3012 },
	{ USB_DEVICE(0x0cf3, 0xe003), .driver_info = BTUSB_ATH3012 },
	{ USB_DEVICE(0x0cf3, 0xe004), .driver_info = BTUSB_ATH3012 },
	{ USB_DEVICE(0x0cf3, 0xe005), .driver_info = BTUSB_ATH3012 },
	{ USB_DEVICE(0x0cf3, 0xe006), .driver_info = BTUSB_ATH3012 },
	{ USB_DEVICE(0x13d3, 0x3362), .driver_info = BTUSB_ATH3012 },
	{ USB_DEVICE(0x13d3, 0x3375), .driver_info = BTUSB_ATH3012 },
	{ USB_DEVICE(0x13d3, 0x3393), .driver_info = BTUSB_ATH3012 },
	{ USB_DEVICE(0x13d3, 0x3395), .driver_info = BTUSB_ATH3012 },
	{ USB_DEVICE(0x13d3, 0x3402), .driver_info = BTUSB_ATH3012 },
	{ USB_DEVICE(0x13d3, 0x3408), .driver_info = BTUSB_ATH3012 },
	{ USB_DEVICE(0x13d3, 0x3423), .driver_info = BTUSB_ATH3012 },
	{ USB_DEVICE(0x13d3, 0x3432), .driver_info = BTUSB_ATH3012 },
	{ USB_DEVICE(0x13d3, 0x3472), .driver_info = BTUSB_ATH3012 },
	{ USB_DEVICE(0x13d3, 0x3474), .driver_info = BTUSB_ATH3012 },
	{ USB_DEVICE(0x13d3, 0x3487), .driver_info = BTUSB_ATH3012 },
	{ USB_DEVICE(0x13d3, 0x3490), .driver_info = BTUSB_ATH3012 },

	/* Atheros AR5BBU12 with sflash firmware */
	{ USB_DEVICE(0x0489, 0xe02c), .driver_info = BTUSB_IGNORE },

	/* Atheros AR5BBU12 with sflash firmware */
	{ USB_DEVICE(0x0489, 0xe036), .driver_info = BTUSB_ATH3012 },
	{ USB_DEVICE(0x0489, 0xe03c), .driver_info = BTUSB_ATH3012 },

	/* QCA ROME chipset */
	{ USB_DEVICE(0x0cf3, 0x535b), .driver_info = BTUSB_QCA_ROME |
						     BTUSB_WIDEBAND_SPEECH },
	{ USB_DEVICE(0x0cf3, 0xe007), .driver_info = BTUSB_QCA_ROME |
						     BTUSB_WIDEBAND_SPEECH },
	{ USB_DEVICE(0x0cf3, 0xe009), .driver_info = BTUSB_QCA_ROME |
						     BTUSB_WIDEBAND_SPEECH },
	{ USB_DEVICE(0x0cf3, 0xe010), .driver_info = BTUSB_QCA_ROME |
						     BTUSB_WIDEBAND_SPEECH },
	{ USB_DEVICE(0x0cf3, 0xe300), .driver_info = BTUSB_QCA_ROME |
						     BTUSB_WIDEBAND_SPEECH },
	{ USB_DEVICE(0x0cf3, 0xe301), .driver_info = BTUSB_QCA_ROME |
						     BTUSB_WIDEBAND_SPEECH },
	{ USB_DEVICE(0x0cf3, 0xe360), .driver_info = BTUSB_QCA_ROME |
						     BTUSB_WIDEBAND_SPEECH },
	{ USB_DEVICE(0x0489, 0xe092), .driver_info = BTUSB_QCA_ROME |
						     BTUSB_WIDEBAND_SPEECH },
	{ USB_DEVICE(0x0489, 0xe09f), .driver_info = BTUSB_QCA_ROME |
						     BTUSB_WIDEBAND_SPEECH },
	{ USB_DEVICE(0x0489, 0xe0a2), .driver_info = BTUSB_QCA_ROME |
						     BTUSB_WIDEBAND_SPEECH },
	{ USB_DEVICE(0x04ca, 0x3011), .driver_info = BTUSB_QCA_ROME |
						     BTUSB_WIDEBAND_SPEECH },
	{ USB_DEVICE(0x04ca, 0x3015), .driver_info = BTUSB_QCA_ROME |
						     BTUSB_WIDEBAND_SPEECH },
	{ USB_DEVICE(0x04ca, 0x3016), .driver_info = BTUSB_QCA_ROME |
						     BTUSB_WIDEBAND_SPEECH },
	{ USB_DEVICE(0x04ca, 0x301a), .driver_info = BTUSB_QCA_ROME |
						     BTUSB_WIDEBAND_SPEECH },
	{ USB_DEVICE(0x04ca, 0x3021), .driver_info = BTUSB_QCA_ROME |
						     BTUSB_WIDEBAND_SPEECH },
	{ USB_DEVICE(0x13d3, 0x3491), .driver_info = BTUSB_QCA_ROME |
						     BTUSB_WIDEBAND_SPEECH },
	{ USB_DEVICE(0x13d3, 0x3496), .driver_info = BTUSB_QCA_ROME |
						     BTUSB_WIDEBAND_SPEECH },
	{ USB_DEVICE(0x13d3, 0x3501), .driver_info = BTUSB_QCA_ROME |
						     BTUSB_WIDEBAND_SPEECH },

	/* QCA WCN6855 chipset */
	{ USB_DEVICE(0x0cf3, 0xe600), .driver_info = BTUSB_QCA_WCN6855 |
						     BTUSB_WIDEBAND_SPEECH },

	/* Broadcom BCM2035 */
	{ USB_DEVICE(0x0a5c, 0x2009), .driver_info = BTUSB_BCM92035 },
	{ USB_DEVICE(0x0a5c, 0x200a), .driver_info = BTUSB_WRONG_SCO_MTU },
	{ USB_DEVICE(0x0a5c, 0x2035), .driver_info = BTUSB_WRONG_SCO_MTU },

	/* Broadcom BCM2045 */
	{ USB_DEVICE(0x0a5c, 0x2039), .driver_info = BTUSB_WRONG_SCO_MTU },
	{ USB_DEVICE(0x0a5c, 0x2101), .driver_info = BTUSB_WRONG_SCO_MTU },

	/* IBM/Lenovo ThinkPad with Broadcom chip */
	{ USB_DEVICE(0x0a5c, 0x201e), .driver_info = BTUSB_WRONG_SCO_MTU },
	{ USB_DEVICE(0x0a5c, 0x2110), .driver_info = BTUSB_WRONG_SCO_MTU },

	/* HP laptop with Broadcom chip */
	{ USB_DEVICE(0x03f0, 0x171d), .driver_info = BTUSB_WRONG_SCO_MTU },

	/* Dell laptop with Broadcom chip */
	{ USB_DEVICE(0x413c, 0x8126), .driver_info = BTUSB_WRONG_SCO_MTU },

	/* Dell Wireless 370 and 410 devices */
	{ USB_DEVICE(0x413c, 0x8152), .driver_info = BTUSB_WRONG_SCO_MTU },
	{ USB_DEVICE(0x413c, 0x8156), .driver_info = BTUSB_WRONG_SCO_MTU },

	/* Belkin F8T012 and F8T013 devices */
	{ USB_DEVICE(0x050d, 0x0012), .driver_info = BTUSB_WRONG_SCO_MTU },
	{ USB_DEVICE(0x050d, 0x0013), .driver_info = BTUSB_WRONG_SCO_MTU },

	/* Asus WL-BTD202 device */
	{ USB_DEVICE(0x0b05, 0x1715), .driver_info = BTUSB_WRONG_SCO_MTU },

	/* Kensington Bluetooth USB adapter */
	{ USB_DEVICE(0x047d, 0x105e), .driver_info = BTUSB_WRONG_SCO_MTU },

	/* RTX Telecom based adapters with buggy SCO support */
	{ USB_DEVICE(0x0400, 0x0807), .driver_info = BTUSB_BROKEN_ISOC },
	{ USB_DEVICE(0x0400, 0x080a), .driver_info = BTUSB_BROKEN_ISOC },

	/* CONWISE Technology based adapters with buggy SCO support */
	{ USB_DEVICE(0x0e5e, 0x6622),
	  .driver_info = BTUSB_BROKEN_ISOC | BTUSB_CW6622},

	/* Roper Class 1 Bluetooth Dongle (Silicon Wave based) */
	{ USB_DEVICE(0x1310, 0x0001), .driver_info = BTUSB_SWAVE },

	/* Digianswer devices */
	{ USB_DEVICE(0x08fd, 0x0001), .driver_info = BTUSB_DIGIANSWER },
	{ USB_DEVICE(0x08fd, 0x0002), .driver_info = BTUSB_IGNORE },

	/* CSR BlueCore Bluetooth Sniffer */
	{ USB_DEVICE(0x0a12, 0x0002),
	  .driver_info = BTUSB_SNIFFER | BTUSB_BROKEN_ISOC },

	/* Frontline ComProbe Bluetooth Sniffer */
	{ USB_DEVICE(0x16d3, 0x0002),
	  .driver_info = BTUSB_SNIFFER | BTUSB_BROKEN_ISOC },

	/* Marvell Bluetooth devices */
	{ USB_DEVICE(0x1286, 0x2044), .driver_info = BTUSB_MARVELL },
	{ USB_DEVICE(0x1286, 0x2046), .driver_info = BTUSB_MARVELL },
	{ USB_DEVICE(0x1286, 0x204e), .driver_info = BTUSB_MARVELL },

	/* Intel Bluetooth devices */
	{ USB_DEVICE(0x8087, 0x0025), .driver_info = BTUSB_INTEL_NEW |
						     BTUSB_WIDEBAND_SPEECH |
						     BTUSB_VALID_LE_STATES },
	{ USB_DEVICE(0x8087, 0x0026), .driver_info = BTUSB_INTEL_NEW |
						     BTUSB_WIDEBAND_SPEECH },
	{ USB_DEVICE(0x8087, 0x0029), .driver_info = BTUSB_INTEL_NEW |
						     BTUSB_WIDEBAND_SPEECH },
	{ USB_DEVICE(0x8087, 0x0032), .driver_info = BTUSB_INTEL_NEWGEN |
						     BTUSB_WIDEBAND_SPEECH},
	{ USB_DEVICE(0x8087, 0x0033), .driver_info = BTUSB_INTEL_NEWGEN |
						     BTUSB_WIDEBAND_SPEECH},
	{ USB_DEVICE(0x8087, 0x07da), .driver_info = BTUSB_CSR },
	{ USB_DEVICE(0x8087, 0x07dc), .driver_info = BTUSB_INTEL },
	{ USB_DEVICE(0x8087, 0x0a2a), .driver_info = BTUSB_INTEL },
	{ USB_DEVICE(0x8087, 0x0a2b), .driver_info = BTUSB_INTEL_NEW |
						     BTUSB_WIDEBAND_SPEECH },
	{ USB_DEVICE(0x8087, 0x0aa7), .driver_info = BTUSB_INTEL |
						     BTUSB_WIDEBAND_SPEECH },
	{ USB_DEVICE(0x8087, 0x0aaa), .driver_info = BTUSB_INTEL_NEW |
						     BTUSB_WIDEBAND_SPEECH |
						     BTUSB_VALID_LE_STATES },

	/* Other Intel Bluetooth devices */
	{ USB_VENDOR_AND_INTERFACE_INFO(0x8087, 0xe0, 0x01, 0x01),
	  .driver_info = BTUSB_IGNORE },

	/* Realtek 8822CE Bluetooth devices */
	{ USB_DEVICE(0x0bda, 0xb00c), .driver_info = BTUSB_REALTEK |
						     BTUSB_WIDEBAND_SPEECH },

	/* Realtek 8852AE Bluetooth devices */
	{ USB_DEVICE(0x0bda, 0xc852), .driver_info = BTUSB_REALTEK |
						     BTUSB_WIDEBAND_SPEECH },

	/* Realtek Bluetooth devices */
	{ USB_VENDOR_AND_INTERFACE_INFO(0x0bda, 0xe0, 0x01, 0x01),
	  .driver_info = BTUSB_REALTEK },

	/* MediaTek Bluetooth devices */
	{ USB_VENDOR_AND_INTERFACE_INFO(0x0e8d, 0xe0, 0x01, 0x01),
	  .driver_info = BTUSB_MEDIATEK },

	/* Additional MediaTek MT7615E Bluetooth devices */
	{ USB_DEVICE(0x13d3, 0x3560), .driver_info = BTUSB_MEDIATEK},

	/* Additional Realtek 8723AE Bluetooth devices */
	{ USB_DEVICE(0x0930, 0x021d), .driver_info = BTUSB_REALTEK },
	{ USB_DEVICE(0x13d3, 0x3394), .driver_info = BTUSB_REALTEK },

	/* Additional Realtek 8723BE Bluetooth devices */
	{ USB_DEVICE(0x0489, 0xe085), .driver_info = BTUSB_REALTEK },
	{ USB_DEVICE(0x0489, 0xe08b), .driver_info = BTUSB_REALTEK },
	{ USB_DEVICE(0x13d3, 0x3410), .driver_info = BTUSB_REALTEK },
	{ USB_DEVICE(0x13d3, 0x3416), .driver_info = BTUSB_REALTEK },
	{ USB_DEVICE(0x13d3, 0x3459), .driver_info = BTUSB_REALTEK },
	{ USB_DEVICE(0x13d3, 0x3494), .driver_info = BTUSB_REALTEK },

	/* Additional Realtek 8723BU Bluetooth devices */
	{ USB_DEVICE(0x7392, 0xa611), .driver_info = BTUSB_REALTEK },

	/* Additional Realtek 8723DE Bluetooth devices */
	{ USB_DEVICE(0x0bda, 0xb009), .driver_info = BTUSB_REALTEK },
	{ USB_DEVICE(0x2ff8, 0xb011), .driver_info = BTUSB_REALTEK },

	/* Additional Realtek 8821AE Bluetooth devices */
	{ USB_DEVICE(0x0b05, 0x17dc), .driver_info = BTUSB_REALTEK },
	{ USB_DEVICE(0x13d3, 0x3414), .driver_info = BTUSB_REALTEK },
	{ USB_DEVICE(0x13d3, 0x3458), .driver_info = BTUSB_REALTEK },
	{ USB_DEVICE(0x13d3, 0x3461), .driver_info = BTUSB_REALTEK },
	{ USB_DEVICE(0x13d3, 0x3462), .driver_info = BTUSB_REALTEK },

	/* Additional Realtek 8822BE Bluetooth devices */
	{ USB_DEVICE(0x13d3, 0x3526), .driver_info = BTUSB_REALTEK },
	{ USB_DEVICE(0x0b05, 0x185c), .driver_info = BTUSB_REALTEK },

	/* Additional Realtek 8822CE Bluetooth devices */
	{ USB_DEVICE(0x04ca, 0x4005), .driver_info = BTUSB_REALTEK |
						     BTUSB_WIDEBAND_SPEECH },
	{ USB_DEVICE(0x04c5, 0x161f), .driver_info = BTUSB_REALTEK |
						     BTUSB_WIDEBAND_SPEECH },
	{ USB_DEVICE(0x0b05, 0x18ef), .driver_info = BTUSB_REALTEK |
						     BTUSB_WIDEBAND_SPEECH },
	{ USB_DEVICE(0x13d3, 0x3548), .driver_info = BTUSB_REALTEK |
						     BTUSB_WIDEBAND_SPEECH },
	{ USB_DEVICE(0x13d3, 0x3549), .driver_info = BTUSB_REALTEK |
						     BTUSB_WIDEBAND_SPEECH },
	{ USB_DEVICE(0x13d3, 0x3553), .driver_info = BTUSB_REALTEK |
						     BTUSB_WIDEBAND_SPEECH },
	{ USB_DEVICE(0x13d3, 0x3555), .driver_info = BTUSB_REALTEK |
						     BTUSB_WIDEBAND_SPEECH },
	{ USB_DEVICE(0x2ff8, 0x3051), .driver_info = BTUSB_REALTEK |
						     BTUSB_WIDEBAND_SPEECH },
	{ USB_DEVICE(0x1358, 0xc123), .driver_info = BTUSB_REALTEK |
						     BTUSB_WIDEBAND_SPEECH },
	{ USB_DEVICE(0x0bda, 0xc123), .driver_info = BTUSB_REALTEK |
						     BTUSB_WIDEBAND_SPEECH },
	{ USB_DEVICE(0x0cb5, 0xc547), .driver_info = BTUSB_REALTEK |
						     BTUSB_WIDEBAND_SPEECH },

	/* Silicon Wave based devices */
	{ USB_DEVICE(0x0c10, 0x0000), .driver_info = BTUSB_SWAVE },

	{ }	/* Terminating entry */
};

/* The Bluetooth USB module build into some devices needs to be reset on resume,
 * this is a problem with the platform (likely shutting off all power) not with
 * the module itself. So we use a DMI list to match known broken platforms.
 */
static const struct dmi_system_id btusb_needs_reset_resume_table[] = {
	{
		/* Dell OptiPlex 3060 (QCA ROME device 0cf3:e007) */
		.matches = {
			DMI_MATCH(DMI_SYS_VENDOR, "Dell Inc."),
			DMI_MATCH(DMI_PRODUCT_NAME, "OptiPlex 3060"),
		},
	},
	{
		/* Dell XPS 9360 (QCA ROME device 0cf3:e300) */
		.matches = {
			DMI_MATCH(DMI_SYS_VENDOR, "Dell Inc."),
			DMI_MATCH(DMI_PRODUCT_NAME, "XPS 13 9360"),
		},
	},
	{
		/* Dell Inspiron 5565 (QCA ROME device 0cf3:e009) */
		.matches = {
			DMI_MATCH(DMI_SYS_VENDOR, "Dell Inc."),
			DMI_MATCH(DMI_PRODUCT_NAME, "Inspiron 5565"),
		},
	},
	{}
};

#define BTUSB_MAX_ISOC_FRAMES	10

#define BTUSB_INTR_RUNNING	0
#define BTUSB_BULK_RUNNING	1
#define BTUSB_ISOC_RUNNING	2
#define BTUSB_SUSPENDING	3
#define BTUSB_DID_ISO_RESUME	4
#define BTUSB_BOOTLOADER	5
#define BTUSB_DOWNLOADING	6
#define BTUSB_FIRMWARE_LOADED	7
#define BTUSB_FIRMWARE_FAILED	8
#define BTUSB_BOOTING		9
#define BTUSB_DIAG_RUNNING	10
#define BTUSB_OOB_WAKE_ENABLED	11
#define BTUSB_HW_RESET_ACTIVE	12
#define BTUSB_TX_WAIT_VND_EVT	13
#define BTUSB_WAKEUP_DISABLE	14

struct btusb_data {
	struct hci_dev       *hdev;
	struct usb_device    *udev;
	struct usb_interface *intf;
	struct usb_interface *isoc;
	struct usb_interface *diag;
	unsigned isoc_ifnum;

	unsigned long flags;

	struct work_struct work;
	struct work_struct waker;

	struct usb_anchor deferred;
	struct usb_anchor tx_anchor;
	int tx_in_flight;
	spinlock_t txlock;

	struct usb_anchor intr_anchor;
	struct usb_anchor bulk_anchor;
	struct usb_anchor isoc_anchor;
	struct usb_anchor diag_anchor;
	struct usb_anchor ctrl_anchor;
	spinlock_t rxlock;

	struct sk_buff *evt_skb;
	struct sk_buff *acl_skb;
	struct sk_buff *sco_skb;

	struct usb_endpoint_descriptor *intr_ep;
	struct usb_endpoint_descriptor *bulk_tx_ep;
	struct usb_endpoint_descriptor *bulk_rx_ep;
	struct usb_endpoint_descriptor *isoc_tx_ep;
	struct usb_endpoint_descriptor *isoc_rx_ep;
	struct usb_endpoint_descriptor *diag_tx_ep;
	struct usb_endpoint_descriptor *diag_rx_ep;

	struct gpio_desc *reset_gpio;

	__u8 cmdreq_type;
	__u8 cmdreq;

	unsigned int sco_num;
	unsigned int air_mode;
	bool usb_alt6_packet_flow;
	int isoc_altsetting;
	int suspend_count;

	int (*recv_event)(struct hci_dev *hdev, struct sk_buff *skb);
	int (*recv_bulk)(struct btusb_data *data, void *buffer, int count);

	int (*setup_on_usb)(struct hci_dev *hdev);

	int oob_wake_irq;   /* irq for out-of-band wake-on-bt */
	unsigned cmd_timeout_cnt;
};

static void btusb_intel_cmd_timeout(struct hci_dev *hdev)
{
	struct btusb_data *data = hci_get_drvdata(hdev);
	struct gpio_desc *reset_gpio = data->reset_gpio;

	if (++data->cmd_timeout_cnt < 5)
		return;

	if (!reset_gpio) {
		bt_dev_err(hdev, "No way to reset. Ignoring and continuing");
		return;
	}

	/*
	 * Toggle the hard reset line if the platform provides one. The reset
	 * is going to yank the device off the USB and then replug. So doing
	 * once is enough. The cleanup is handled correctly on the way out
	 * (standard USB disconnect), and the new device is detected cleanly
	 * and bound to the driver again like it should be.
	 */
	if (test_and_set_bit(BTUSB_HW_RESET_ACTIVE, &data->flags)) {
		bt_dev_err(hdev, "last reset failed? Not resetting again");
		return;
	}

	bt_dev_err(hdev, "Initiating HW reset via gpio");
	gpiod_set_value_cansleep(reset_gpio, 1);
	msleep(100);
	gpiod_set_value_cansleep(reset_gpio, 0);
}

static void btusb_rtl_cmd_timeout(struct hci_dev *hdev)
{
	struct btusb_data *data = hci_get_drvdata(hdev);
	struct gpio_desc *reset_gpio = data->reset_gpio;

	if (++data->cmd_timeout_cnt < 5)
		return;

	if (!reset_gpio) {
		bt_dev_err(hdev, "No gpio to reset Realtek device, ignoring");
		return;
	}

	/* Toggle the hard reset line. The Realtek device is going to
	 * yank itself off the USB and then replug. The cleanup is handled
	 * correctly on the way out (standard USB disconnect), and the new
	 * device is detected cleanly and bound to the driver again like
	 * it should be.
	 */
	if (test_and_set_bit(BTUSB_HW_RESET_ACTIVE, &data->flags)) {
		bt_dev_err(hdev, "last reset failed? Not resetting again");
		return;
	}

	bt_dev_err(hdev, "Reset Realtek device via gpio");
	gpiod_set_value_cansleep(reset_gpio, 1);
	msleep(200);
	gpiod_set_value_cansleep(reset_gpio, 0);
}

static void btusb_qca_cmd_timeout(struct hci_dev *hdev)
{
	struct btusb_data *data = hci_get_drvdata(hdev);
	int err;

	if (++data->cmd_timeout_cnt < 5)
		return;

	bt_dev_err(hdev, "Multiple cmd timeouts seen. Resetting usb device.");
	/* This is not an unbalanced PM reference since the device will reset */
	err = usb_autopm_get_interface(data->intf);
	if (!err)
		usb_queue_reset_device(data->intf);
	else
		bt_dev_err(hdev, "Failed usb_autopm_get_interface with %d", err);
}

static inline void btusb_free_frags(struct btusb_data *data)
{
	unsigned long flags;

	spin_lock_irqsave(&data->rxlock, flags);

	kfree_skb(data->evt_skb);
	data->evt_skb = NULL;

	kfree_skb(data->acl_skb);
	data->acl_skb = NULL;

	kfree_skb(data->sco_skb);
	data->sco_skb = NULL;

	spin_unlock_irqrestore(&data->rxlock, flags);
}

static int btusb_recv_intr(struct btusb_data *data, void *buffer, int count)
{
	struct sk_buff *skb;
	unsigned long flags;
	int err = 0;

	spin_lock_irqsave(&data->rxlock, flags);
	skb = data->evt_skb;

	while (count) {
		int len;

		if (!skb) {
			skb = bt_skb_alloc(HCI_MAX_EVENT_SIZE, GFP_ATOMIC);
			if (!skb) {
				err = -ENOMEM;
				break;
			}

			hci_skb_pkt_type(skb) = HCI_EVENT_PKT;
			hci_skb_expect(skb) = HCI_EVENT_HDR_SIZE;
		}

		len = min_t(uint, hci_skb_expect(skb), count);
		skb_put_data(skb, buffer, len);

		count -= len;
		buffer += len;
		hci_skb_expect(skb) -= len;

		if (skb->len == HCI_EVENT_HDR_SIZE) {
			/* Complete event header */
			hci_skb_expect(skb) = hci_event_hdr(skb)->plen;

			if (skb_tailroom(skb) < hci_skb_expect(skb)) {
				kfree_skb(skb);
				skb = NULL;

				err = -EILSEQ;
				break;
			}
		}

		if (!hci_skb_expect(skb)) {
			/* Complete frame */
			data->recv_event(data->hdev, skb);
			skb = NULL;
		}
	}

	data->evt_skb = skb;
	spin_unlock_irqrestore(&data->rxlock, flags);

	return err;
}

static int btusb_recv_bulk(struct btusb_data *data, void *buffer, int count)
{
	struct sk_buff *skb;
	unsigned long flags;
	int err = 0;

	spin_lock_irqsave(&data->rxlock, flags);
	skb = data->acl_skb;

	while (count) {
		int len;

		if (!skb) {
			skb = bt_skb_alloc(HCI_MAX_FRAME_SIZE, GFP_ATOMIC);
			if (!skb) {
				err = -ENOMEM;
				break;
			}

			hci_skb_pkt_type(skb) = HCI_ACLDATA_PKT;
			hci_skb_expect(skb) = HCI_ACL_HDR_SIZE;
		}

		len = min_t(uint, hci_skb_expect(skb), count);
		skb_put_data(skb, buffer, len);

		count -= len;
		buffer += len;
		hci_skb_expect(skb) -= len;

		if (skb->len == HCI_ACL_HDR_SIZE) {
			__le16 dlen = hci_acl_hdr(skb)->dlen;

			/* Complete ACL header */
			hci_skb_expect(skb) = __le16_to_cpu(dlen);

			if (skb_tailroom(skb) < hci_skb_expect(skb)) {
				kfree_skb(skb);
				skb = NULL;

				err = -EILSEQ;
				break;
			}
		}

		if (!hci_skb_expect(skb)) {
			/* Complete frame */
			hci_recv_frame(data->hdev, skb);
			skb = NULL;
		}
	}

	data->acl_skb = skb;
	spin_unlock_irqrestore(&data->rxlock, flags);

	return err;
}

static int btusb_recv_isoc(struct btusb_data *data, void *buffer, int count)
{
	struct sk_buff *skb;
	unsigned long flags;
	int err = 0;

	spin_lock_irqsave(&data->rxlock, flags);
	skb = data->sco_skb;

	while (count) {
		int len;

		if (!skb) {
			skb = bt_skb_alloc(HCI_MAX_SCO_SIZE, GFP_ATOMIC);
			if (!skb) {
				err = -ENOMEM;
				break;
			}

			hci_skb_pkt_type(skb) = HCI_SCODATA_PKT;
			hci_skb_expect(skb) = HCI_SCO_HDR_SIZE;
		}

		len = min_t(uint, hci_skb_expect(skb), count);
		skb_put_data(skb, buffer, len);

		count -= len;
		buffer += len;
		hci_skb_expect(skb) -= len;

		if (skb->len == HCI_SCO_HDR_SIZE) {
			/* Complete SCO header */
			hci_skb_expect(skb) = hci_sco_hdr(skb)->dlen;

			if (skb_tailroom(skb) < hci_skb_expect(skb)) {
				kfree_skb(skb);
				skb = NULL;

				err = -EILSEQ;
				break;
			}
		}

		if (!hci_skb_expect(skb)) {
			/* Complete frame */
			hci_recv_frame(data->hdev, skb);
			skb = NULL;
		}
	}

	data->sco_skb = skb;
	spin_unlock_irqrestore(&data->rxlock, flags);

	return err;
}

static void btusb_intr_complete(struct urb *urb)
{
	struct hci_dev *hdev = urb->context;
	struct btusb_data *data = hci_get_drvdata(hdev);
	int err;

	BT_DBG("%s urb %p status %d count %d", hdev->name, urb, urb->status,
	       urb->actual_length);

	if (!test_bit(HCI_RUNNING, &hdev->flags))
		return;

	if (urb->status == 0) {
		hdev->stat.byte_rx += urb->actual_length;

		if (btusb_recv_intr(data, urb->transfer_buffer,
				    urb->actual_length) < 0) {
			bt_dev_err(hdev, "corrupted event packet");
			hdev->stat.err_rx++;
		}
	} else if (urb->status == -ENOENT) {
		/* Avoid suspend failed when usb_kill_urb */
		return;
	}

	if (!test_bit(BTUSB_INTR_RUNNING, &data->flags))
		return;

	usb_mark_last_busy(data->udev);
	usb_anchor_urb(urb, &data->intr_anchor);

	err = usb_submit_urb(urb, GFP_ATOMIC);
	if (err < 0) {
		/* -EPERM: urb is being killed;
		 * -ENODEV: device got disconnected
		 */
		if (err != -EPERM && err != -ENODEV)
			bt_dev_err(hdev, "urb %p failed to resubmit (%d)",
				   urb, -err);
		usb_unanchor_urb(urb);
	}
}

static int btusb_submit_intr_urb(struct hci_dev *hdev, gfp_t mem_flags)
{
	struct btusb_data *data = hci_get_drvdata(hdev);
	struct urb *urb;
	unsigned char *buf;
	unsigned int pipe;
	int err, size;

	BT_DBG("%s", hdev->name);

	if (!data->intr_ep)
		return -ENODEV;

	urb = usb_alloc_urb(0, mem_flags);
	if (!urb)
		return -ENOMEM;

	size = le16_to_cpu(data->intr_ep->wMaxPacketSize);

	buf = kmalloc(size, mem_flags);
	if (!buf) {
		usb_free_urb(urb);
		return -ENOMEM;
	}

	pipe = usb_rcvintpipe(data->udev, data->intr_ep->bEndpointAddress);

	usb_fill_int_urb(urb, data->udev, pipe, buf, size,
			 btusb_intr_complete, hdev, data->intr_ep->bInterval);

	urb->transfer_flags |= URB_FREE_BUFFER;

	usb_anchor_urb(urb, &data->intr_anchor);

	err = usb_submit_urb(urb, mem_flags);
	if (err < 0) {
		if (err != -EPERM && err != -ENODEV)
			bt_dev_err(hdev, "urb %p submission failed (%d)",
				   urb, -err);
		usb_unanchor_urb(urb);
	}

	usb_free_urb(urb);

	return err;
}

static void btusb_bulk_complete(struct urb *urb)
{
	struct hci_dev *hdev = urb->context;
	struct btusb_data *data = hci_get_drvdata(hdev);
	int err;

	BT_DBG("%s urb %p status %d count %d", hdev->name, urb, urb->status,
	       urb->actual_length);

	if (!test_bit(HCI_RUNNING, &hdev->flags))
		return;

	if (urb->status == 0) {
		hdev->stat.byte_rx += urb->actual_length;

		if (data->recv_bulk(data, urb->transfer_buffer,
				    urb->actual_length) < 0) {
			bt_dev_err(hdev, "corrupted ACL packet");
			hdev->stat.err_rx++;
		}
	} else if (urb->status == -ENOENT) {
		/* Avoid suspend failed when usb_kill_urb */
		return;
	}

	if (!test_bit(BTUSB_BULK_RUNNING, &data->flags))
		return;

	usb_anchor_urb(urb, &data->bulk_anchor);
	usb_mark_last_busy(data->udev);

	err = usb_submit_urb(urb, GFP_ATOMIC);
	if (err < 0) {
		/* -EPERM: urb is being killed;
		 * -ENODEV: device got disconnected
		 */
		if (err != -EPERM && err != -ENODEV)
			bt_dev_err(hdev, "urb %p failed to resubmit (%d)",
				   urb, -err);
		usb_unanchor_urb(urb);
	}
}

static int btusb_submit_bulk_urb(struct hci_dev *hdev, gfp_t mem_flags)
{
	struct btusb_data *data = hci_get_drvdata(hdev);
	struct urb *urb;
	unsigned char *buf;
	unsigned int pipe;
	int err, size = HCI_MAX_FRAME_SIZE;

	BT_DBG("%s", hdev->name);

	if (!data->bulk_rx_ep)
		return -ENODEV;

	urb = usb_alloc_urb(0, mem_flags);
	if (!urb)
		return -ENOMEM;

	buf = kmalloc(size, mem_flags);
	if (!buf) {
		usb_free_urb(urb);
		return -ENOMEM;
	}

	pipe = usb_rcvbulkpipe(data->udev, data->bulk_rx_ep->bEndpointAddress);

	usb_fill_bulk_urb(urb, data->udev, pipe, buf, size,
			  btusb_bulk_complete, hdev);

	urb->transfer_flags |= URB_FREE_BUFFER;

	usb_mark_last_busy(data->udev);
	usb_anchor_urb(urb, &data->bulk_anchor);

	err = usb_submit_urb(urb, mem_flags);
	if (err < 0) {
		if (err != -EPERM && err != -ENODEV)
			bt_dev_err(hdev, "urb %p submission failed (%d)",
				   urb, -err);
		usb_unanchor_urb(urb);
	}

	usb_free_urb(urb);

	return err;
}

static void btusb_isoc_complete(struct urb *urb)
{
	struct hci_dev *hdev = urb->context;
	struct btusb_data *data = hci_get_drvdata(hdev);
	int i, err;

	BT_DBG("%s urb %p status %d count %d", hdev->name, urb, urb->status,
	       urb->actual_length);

	if (!test_bit(HCI_RUNNING, &hdev->flags))
		return;

	if (urb->status == 0) {
		for (i = 0; i < urb->number_of_packets; i++) {
			unsigned int offset = urb->iso_frame_desc[i].offset;
			unsigned int length = urb->iso_frame_desc[i].actual_length;

			if (urb->iso_frame_desc[i].status)
				continue;

			hdev->stat.byte_rx += length;

			if (btusb_recv_isoc(data, urb->transfer_buffer + offset,
					    length) < 0) {
				bt_dev_err(hdev, "corrupted SCO packet");
				hdev->stat.err_rx++;
			}
		}
	} else if (urb->status == -ENOENT) {
		/* Avoid suspend failed when usb_kill_urb */
		return;
	}

	if (!test_bit(BTUSB_ISOC_RUNNING, &data->flags))
		return;

	usb_anchor_urb(urb, &data->isoc_anchor);

	err = usb_submit_urb(urb, GFP_ATOMIC);
	if (err < 0) {
		/* -EPERM: urb is being killed;
		 * -ENODEV: device got disconnected
		 */
		if (err != -EPERM && err != -ENODEV)
			bt_dev_err(hdev, "urb %p failed to resubmit (%d)",
				   urb, -err);
		usb_unanchor_urb(urb);
	}
}

static inline void __fill_isoc_descriptor_msbc(struct urb *urb, int len,
					       int mtu, struct btusb_data *data)
{
	int i, offset = 0;
	unsigned int interval;

	BT_DBG("len %d mtu %d", len, mtu);

	/* For mSBC ALT 6 setting the host will send the packet at continuous
	 * flow. As per core spec 5, vol 4, part B, table 2.1. For ALT setting
	 * 6 the HCI PACKET INTERVAL should be 7.5ms for every usb packets.
	 * To maintain the rate we send 63bytes of usb packets alternatively for
	 * 7ms and 8ms to maintain the rate as 7.5ms.
	 */
	if (data->usb_alt6_packet_flow) {
		interval = 7;
		data->usb_alt6_packet_flow = false;
	} else {
		interval = 6;
		data->usb_alt6_packet_flow = true;
	}

	for (i = 0; i < interval; i++) {
		urb->iso_frame_desc[i].offset = offset;
		urb->iso_frame_desc[i].length = offset;
	}

	if (len && i < BTUSB_MAX_ISOC_FRAMES) {
		urb->iso_frame_desc[i].offset = offset;
		urb->iso_frame_desc[i].length = len;
		i++;
	}

	urb->number_of_packets = i;
}

static inline void __fill_isoc_descriptor(struct urb *urb, int len, int mtu)
{
	int i, offset = 0;

	BT_DBG("len %d mtu %d", len, mtu);

	for (i = 0; i < BTUSB_MAX_ISOC_FRAMES && len >= mtu;
					i++, offset += mtu, len -= mtu) {
		urb->iso_frame_desc[i].offset = offset;
		urb->iso_frame_desc[i].length = mtu;
	}

	if (len && i < BTUSB_MAX_ISOC_FRAMES) {
		urb->iso_frame_desc[i].offset = offset;
		urb->iso_frame_desc[i].length = len;
		i++;
	}

	urb->number_of_packets = i;
}

static int btusb_submit_isoc_urb(struct hci_dev *hdev, gfp_t mem_flags)
{
	struct btusb_data *data = hci_get_drvdata(hdev);
	struct urb *urb;
	unsigned char *buf;
	unsigned int pipe;
	int err, size;

	BT_DBG("%s", hdev->name);

	if (!data->isoc_rx_ep)
		return -ENODEV;

	urb = usb_alloc_urb(BTUSB_MAX_ISOC_FRAMES, mem_flags);
	if (!urb)
		return -ENOMEM;

	size = le16_to_cpu(data->isoc_rx_ep->wMaxPacketSize) *
						BTUSB_MAX_ISOC_FRAMES;

	buf = kmalloc(size, mem_flags);
	if (!buf) {
		usb_free_urb(urb);
		return -ENOMEM;
	}

	pipe = usb_rcvisocpipe(data->udev, data->isoc_rx_ep->bEndpointAddress);

	usb_fill_int_urb(urb, data->udev, pipe, buf, size, btusb_isoc_complete,
			 hdev, data->isoc_rx_ep->bInterval);

	urb->transfer_flags = URB_FREE_BUFFER | URB_ISO_ASAP;

	__fill_isoc_descriptor(urb, size,
			       le16_to_cpu(data->isoc_rx_ep->wMaxPacketSize));

	usb_anchor_urb(urb, &data->isoc_anchor);

	err = usb_submit_urb(urb, mem_flags);
	if (err < 0) {
		if (err != -EPERM && err != -ENODEV)
			bt_dev_err(hdev, "urb %p submission failed (%d)",
				   urb, -err);
		usb_unanchor_urb(urb);
	}

	usb_free_urb(urb);

	return err;
}

static void btusb_diag_complete(struct urb *urb)
{
	struct hci_dev *hdev = urb->context;
	struct btusb_data *data = hci_get_drvdata(hdev);
	int err;

	BT_DBG("%s urb %p status %d count %d", hdev->name, urb, urb->status,
	       urb->actual_length);

	if (urb->status == 0) {
		struct sk_buff *skb;

		skb = bt_skb_alloc(urb->actual_length, GFP_ATOMIC);
		if (skb) {
			skb_put_data(skb, urb->transfer_buffer,
				     urb->actual_length);
			hci_recv_diag(hdev, skb);
		}
	} else if (urb->status == -ENOENT) {
		/* Avoid suspend failed when usb_kill_urb */
		return;
	}

	if (!test_bit(BTUSB_DIAG_RUNNING, &data->flags))
		return;

	usb_anchor_urb(urb, &data->diag_anchor);
	usb_mark_last_busy(data->udev);

	err = usb_submit_urb(urb, GFP_ATOMIC);
	if (err < 0) {
		/* -EPERM: urb is being killed;
		 * -ENODEV: device got disconnected
		 */
		if (err != -EPERM && err != -ENODEV)
			bt_dev_err(hdev, "urb %p failed to resubmit (%d)",
				   urb, -err);
		usb_unanchor_urb(urb);
	}
}

static int btusb_submit_diag_urb(struct hci_dev *hdev, gfp_t mem_flags)
{
	struct btusb_data *data = hci_get_drvdata(hdev);
	struct urb *urb;
	unsigned char *buf;
	unsigned int pipe;
	int err, size = HCI_MAX_FRAME_SIZE;

	BT_DBG("%s", hdev->name);

	if (!data->diag_rx_ep)
		return -ENODEV;

	urb = usb_alloc_urb(0, mem_flags);
	if (!urb)
		return -ENOMEM;

	buf = kmalloc(size, mem_flags);
	if (!buf) {
		usb_free_urb(urb);
		return -ENOMEM;
	}

	pipe = usb_rcvbulkpipe(data->udev, data->diag_rx_ep->bEndpointAddress);

	usb_fill_bulk_urb(urb, data->udev, pipe, buf, size,
			  btusb_diag_complete, hdev);

	urb->transfer_flags |= URB_FREE_BUFFER;

	usb_mark_last_busy(data->udev);
	usb_anchor_urb(urb, &data->diag_anchor);

	err = usb_submit_urb(urb, mem_flags);
	if (err < 0) {
		if (err != -EPERM && err != -ENODEV)
			bt_dev_err(hdev, "urb %p submission failed (%d)",
				   urb, -err);
		usb_unanchor_urb(urb);
	}

	usb_free_urb(urb);

	return err;
}

static void btusb_tx_complete(struct urb *urb)
{
	struct sk_buff *skb = urb->context;
	struct hci_dev *hdev = (struct hci_dev *)skb->dev;
	struct btusb_data *data = hci_get_drvdata(hdev);
	unsigned long flags;

	BT_DBG("%s urb %p status %d count %d", hdev->name, urb, urb->status,
	       urb->actual_length);

	if (!test_bit(HCI_RUNNING, &hdev->flags))
		goto done;

	if (!urb->status)
		hdev->stat.byte_tx += urb->transfer_buffer_length;
	else
		hdev->stat.err_tx++;

done:
	spin_lock_irqsave(&data->txlock, flags);
	data->tx_in_flight--;
	spin_unlock_irqrestore(&data->txlock, flags);

	kfree(urb->setup_packet);

	kfree_skb(skb);
}

static void btusb_isoc_tx_complete(struct urb *urb)
{
	struct sk_buff *skb = urb->context;
	struct hci_dev *hdev = (struct hci_dev *)skb->dev;

	BT_DBG("%s urb %p status %d count %d", hdev->name, urb, urb->status,
	       urb->actual_length);

	if (!test_bit(HCI_RUNNING, &hdev->flags))
		goto done;

	if (!urb->status)
		hdev->stat.byte_tx += urb->transfer_buffer_length;
	else
		hdev->stat.err_tx++;

done:
	kfree(urb->setup_packet);

	kfree_skb(skb);
}

static int btusb_open(struct hci_dev *hdev)
{
	struct btusb_data *data = hci_get_drvdata(hdev);
	int err;

	BT_DBG("%s", hdev->name);

	err = usb_autopm_get_interface(data->intf);
	if (err < 0)
		return err;

	/* Patching USB firmware files prior to starting any URBs of HCI path
	 * It is more safe to use USB bulk channel for downloading USB patch
	 */
	if (data->setup_on_usb) {
		err = data->setup_on_usb(hdev);
		if (err < 0)
			goto setup_fail;
	}

	data->intf->needs_remote_wakeup = 1;

	/* Disable device remote wakeup when host is suspended
	 * For Realtek chips, global suspend without
	 * SET_FEATURE (DEVICE_REMOTE_WAKEUP) can save more power in device.
	 */
	if (test_bit(BTUSB_WAKEUP_DISABLE, &data->flags))
		device_wakeup_disable(&data->udev->dev);

	if (test_and_set_bit(BTUSB_INTR_RUNNING, &data->flags))
		goto done;

	err = btusb_submit_intr_urb(hdev, GFP_KERNEL);
	if (err < 0)
		goto failed;

	err = btusb_submit_bulk_urb(hdev, GFP_KERNEL);
	if (err < 0) {
		usb_kill_anchored_urbs(&data->intr_anchor);
		goto failed;
	}

	set_bit(BTUSB_BULK_RUNNING, &data->flags);
	btusb_submit_bulk_urb(hdev, GFP_KERNEL);

	if (data->diag) {
		if (!btusb_submit_diag_urb(hdev, GFP_KERNEL))
			set_bit(BTUSB_DIAG_RUNNING, &data->flags);
	}

done:
	usb_autopm_put_interface(data->intf);
	return 0;

failed:
	clear_bit(BTUSB_INTR_RUNNING, &data->flags);
setup_fail:
	usb_autopm_put_interface(data->intf);
	return err;
}

static void btusb_stop_traffic(struct btusb_data *data)
{
	usb_kill_anchored_urbs(&data->intr_anchor);
	usb_kill_anchored_urbs(&data->bulk_anchor);
	usb_kill_anchored_urbs(&data->isoc_anchor);
	usb_kill_anchored_urbs(&data->diag_anchor);
	usb_kill_anchored_urbs(&data->ctrl_anchor);
}

static int btusb_close(struct hci_dev *hdev)
{
	struct btusb_data *data = hci_get_drvdata(hdev);
	int err;

	BT_DBG("%s", hdev->name);

	cancel_work_sync(&data->work);
	cancel_work_sync(&data->waker);

	clear_bit(BTUSB_ISOC_RUNNING, &data->flags);
	clear_bit(BTUSB_BULK_RUNNING, &data->flags);
	clear_bit(BTUSB_INTR_RUNNING, &data->flags);
	clear_bit(BTUSB_DIAG_RUNNING, &data->flags);

	btusb_stop_traffic(data);
	btusb_free_frags(data);

	err = usb_autopm_get_interface(data->intf);
	if (err < 0)
		goto failed;

	data->intf->needs_remote_wakeup = 0;

	/* Enable remote wake up for auto-suspend */
	if (test_bit(BTUSB_WAKEUP_DISABLE, &data->flags))
		data->intf->needs_remote_wakeup = 1;

	usb_autopm_put_interface(data->intf);

failed:
	usb_scuttle_anchored_urbs(&data->deferred);
	return 0;
}

static int btusb_flush(struct hci_dev *hdev)
{
	struct btusb_data *data = hci_get_drvdata(hdev);

	BT_DBG("%s", hdev->name);

	usb_kill_anchored_urbs(&data->tx_anchor);
	btusb_free_frags(data);

	return 0;
}

static struct urb *alloc_ctrl_urb(struct hci_dev *hdev, struct sk_buff *skb)
{
	struct btusb_data *data = hci_get_drvdata(hdev);
	struct usb_ctrlrequest *dr;
	struct urb *urb;
	unsigned int pipe;

	urb = usb_alloc_urb(0, GFP_KERNEL);
	if (!urb)
		return ERR_PTR(-ENOMEM);

	dr = kmalloc(sizeof(*dr), GFP_KERNEL);
	if (!dr) {
		usb_free_urb(urb);
		return ERR_PTR(-ENOMEM);
	}

	dr->bRequestType = data->cmdreq_type;
	dr->bRequest     = data->cmdreq;
	dr->wIndex       = 0;
	dr->wValue       = 0;
	dr->wLength      = __cpu_to_le16(skb->len);

	pipe = usb_sndctrlpipe(data->udev, 0x00);

	usb_fill_control_urb(urb, data->udev, pipe, (void *)dr,
			     skb->data, skb->len, btusb_tx_complete, skb);

	skb->dev = (void *)hdev;

	return urb;
}

static struct urb *alloc_bulk_urb(struct hci_dev *hdev, struct sk_buff *skb)
{
	struct btusb_data *data = hci_get_drvdata(hdev);
	struct urb *urb;
	unsigned int pipe;

	if (!data->bulk_tx_ep)
		return ERR_PTR(-ENODEV);

	urb = usb_alloc_urb(0, GFP_KERNEL);
	if (!urb)
		return ERR_PTR(-ENOMEM);

	pipe = usb_sndbulkpipe(data->udev, data->bulk_tx_ep->bEndpointAddress);

	usb_fill_bulk_urb(urb, data->udev, pipe,
			  skb->data, skb->len, btusb_tx_complete, skb);

	skb->dev = (void *)hdev;

	return urb;
}

static struct urb *alloc_isoc_urb(struct hci_dev *hdev, struct sk_buff *skb)
{
	struct btusb_data *data = hci_get_drvdata(hdev);
	struct urb *urb;
	unsigned int pipe;

	if (!data->isoc_tx_ep)
		return ERR_PTR(-ENODEV);

	urb = usb_alloc_urb(BTUSB_MAX_ISOC_FRAMES, GFP_KERNEL);
	if (!urb)
		return ERR_PTR(-ENOMEM);

	pipe = usb_sndisocpipe(data->udev, data->isoc_tx_ep->bEndpointAddress);

	usb_fill_int_urb(urb, data->udev, pipe,
			 skb->data, skb->len, btusb_isoc_tx_complete,
			 skb, data->isoc_tx_ep->bInterval);

	urb->transfer_flags  = URB_ISO_ASAP;

	if (data->isoc_altsetting == 6)
		__fill_isoc_descriptor_msbc(urb, skb->len,
					    le16_to_cpu(data->isoc_tx_ep->wMaxPacketSize),
					    data);
	else
		__fill_isoc_descriptor(urb, skb->len,
				       le16_to_cpu(data->isoc_tx_ep->wMaxPacketSize));
	skb->dev = (void *)hdev;

	return urb;
}

static int submit_tx_urb(struct hci_dev *hdev, struct urb *urb)
{
	struct btusb_data *data = hci_get_drvdata(hdev);
	int err;

	usb_anchor_urb(urb, &data->tx_anchor);

	err = usb_submit_urb(urb, GFP_KERNEL);
	if (err < 0) {
		if (err != -EPERM && err != -ENODEV)
			bt_dev_err(hdev, "urb %p submission failed (%d)",
				   urb, -err);
		kfree(urb->setup_packet);
		usb_unanchor_urb(urb);
	} else {
		usb_mark_last_busy(data->udev);
	}

	usb_free_urb(urb);
	return err;
}

static int submit_or_queue_tx_urb(struct hci_dev *hdev, struct urb *urb)
{
	struct btusb_data *data = hci_get_drvdata(hdev);
	unsigned long flags;
	bool suspending;

	spin_lock_irqsave(&data->txlock, flags);
	suspending = test_bit(BTUSB_SUSPENDING, &data->flags);
	if (!suspending)
		data->tx_in_flight++;
	spin_unlock_irqrestore(&data->txlock, flags);

	if (!suspending)
		return submit_tx_urb(hdev, urb);

	usb_anchor_urb(urb, &data->deferred);
	schedule_work(&data->waker);

	usb_free_urb(urb);
	return 0;
}

static int btusb_send_frame(struct hci_dev *hdev, struct sk_buff *skb)
{
	struct urb *urb;

	BT_DBG("%s", hdev->name);

	switch (hci_skb_pkt_type(skb)) {
	case HCI_COMMAND_PKT:
		urb = alloc_ctrl_urb(hdev, skb);
		if (IS_ERR(urb))
			return PTR_ERR(urb);

		hdev->stat.cmd_tx++;
		return submit_or_queue_tx_urb(hdev, urb);

	case HCI_ACLDATA_PKT:
		urb = alloc_bulk_urb(hdev, skb);
		if (IS_ERR(urb))
			return PTR_ERR(urb);

		hdev->stat.acl_tx++;
		return submit_or_queue_tx_urb(hdev, urb);

	case HCI_SCODATA_PKT:
		if (hci_conn_num(hdev, SCO_LINK) < 1)
			return -ENODEV;

		urb = alloc_isoc_urb(hdev, skb);
		if (IS_ERR(urb))
			return PTR_ERR(urb);

		hdev->stat.sco_tx++;
		return submit_tx_urb(hdev, urb);
	}

	return -EILSEQ;
}

static void btusb_notify(struct hci_dev *hdev, unsigned int evt)
{
	struct btusb_data *data = hci_get_drvdata(hdev);

	BT_DBG("%s evt %d", hdev->name, evt);

	if (hci_conn_num(hdev, SCO_LINK) != data->sco_num) {
		data->sco_num = hci_conn_num(hdev, SCO_LINK);
		data->air_mode = evt;
		schedule_work(&data->work);
	}
}

static inline int __set_isoc_interface(struct hci_dev *hdev, int altsetting)
{
	struct btusb_data *data = hci_get_drvdata(hdev);
	struct usb_interface *intf = data->isoc;
	struct usb_endpoint_descriptor *ep_desc;
	int i, err;

	if (!data->isoc)
		return -ENODEV;

	err = usb_set_interface(data->udev, data->isoc_ifnum, altsetting);
	if (err < 0) {
		bt_dev_err(hdev, "setting interface failed (%d)", -err);
		return err;
	}

	data->isoc_altsetting = altsetting;

	data->isoc_tx_ep = NULL;
	data->isoc_rx_ep = NULL;

	for (i = 0; i < intf->cur_altsetting->desc.bNumEndpoints; i++) {
		ep_desc = &intf->cur_altsetting->endpoint[i].desc;

		if (!data->isoc_tx_ep && usb_endpoint_is_isoc_out(ep_desc)) {
			data->isoc_tx_ep = ep_desc;
			continue;
		}

		if (!data->isoc_rx_ep && usb_endpoint_is_isoc_in(ep_desc)) {
			data->isoc_rx_ep = ep_desc;
			continue;
		}
	}

	if (!data->isoc_tx_ep || !data->isoc_rx_ep) {
		bt_dev_err(hdev, "invalid SCO descriptors");
		return -ENODEV;
	}

	return 0;
}

static int btusb_switch_alt_setting(struct hci_dev *hdev, int new_alts)
{
	struct btusb_data *data = hci_get_drvdata(hdev);
	int err;

	if (data->isoc_altsetting != new_alts) {
		unsigned long flags;

		clear_bit(BTUSB_ISOC_RUNNING, &data->flags);
		usb_kill_anchored_urbs(&data->isoc_anchor);

		/* When isochronous alternate setting needs to be
		 * changed, because SCO connection has been added
		 * or removed, a packet fragment may be left in the
		 * reassembling state. This could lead to wrongly
		 * assembled fragments.
		 *
		 * Clear outstanding fragment when selecting a new
		 * alternate setting.
		 */
		spin_lock_irqsave(&data->rxlock, flags);
		kfree_skb(data->sco_skb);
		data->sco_skb = NULL;
		spin_unlock_irqrestore(&data->rxlock, flags);

		err = __set_isoc_interface(hdev, new_alts);
		if (err < 0)
			return err;
	}

	if (!test_and_set_bit(BTUSB_ISOC_RUNNING, &data->flags)) {
		if (btusb_submit_isoc_urb(hdev, GFP_KERNEL) < 0)
			clear_bit(BTUSB_ISOC_RUNNING, &data->flags);
		else
			btusb_submit_isoc_urb(hdev, GFP_KERNEL);
	}

	return 0;
}

static struct usb_host_interface *btusb_find_altsetting(struct btusb_data *data,
							int alt)
{
	struct usb_interface *intf = data->isoc;
	int i;

	BT_DBG("Looking for Alt no :%d", alt);

	if (!intf)
		return NULL;

	for (i = 0; i < intf->num_altsetting; i++) {
		if (intf->altsetting[i].desc.bAlternateSetting == alt)
			return &intf->altsetting[i];
	}

	return NULL;
}

static void btusb_work(struct work_struct *work)
{
	struct btusb_data *data = container_of(work, struct btusb_data, work);
	struct hci_dev *hdev = data->hdev;
	int new_alts = 0;
	int err;

	if (data->sco_num > 0) {
		if (!test_bit(BTUSB_DID_ISO_RESUME, &data->flags)) {
			err = usb_autopm_get_interface(data->isoc ? data->isoc : data->intf);
			if (err < 0) {
				clear_bit(BTUSB_ISOC_RUNNING, &data->flags);
				usb_kill_anchored_urbs(&data->isoc_anchor);
				return;
			}

			set_bit(BTUSB_DID_ISO_RESUME, &data->flags);
		}

		if (data->air_mode == HCI_NOTIFY_ENABLE_SCO_CVSD) {
			if (hdev->voice_setting & 0x0020) {
				static const int alts[3] = { 2, 4, 5 };

				new_alts = alts[data->sco_num - 1];
			} else {
				new_alts = data->sco_num;
			}
		} else if (data->air_mode == HCI_NOTIFY_ENABLE_SCO_TRANSP) {
			/* Bluetooth USB spec recommends alt 6 (63 bytes), but
			 * many adapters do not support it.  Alt 1 appears to
			 * work for all adapters that do not have alt 6, and
			 * which work with WBS at all.
			 */
			new_alts = btusb_find_altsetting(data, 6) ? 6 : 1;
		}

		if (btusb_switch_alt_setting(hdev, new_alts) < 0)
			bt_dev_err(hdev, "set USB alt:(%d) failed!", new_alts);
	} else {
		clear_bit(BTUSB_ISOC_RUNNING, &data->flags);
		usb_kill_anchored_urbs(&data->isoc_anchor);

		__set_isoc_interface(hdev, 0);
		if (test_and_clear_bit(BTUSB_DID_ISO_RESUME, &data->flags))
			usb_autopm_put_interface(data->isoc ? data->isoc : data->intf);
	}
}

static void btusb_waker(struct work_struct *work)
{
	struct btusb_data *data = container_of(work, struct btusb_data, waker);
	int err;

	err = usb_autopm_get_interface(data->intf);
	if (err < 0)
		return;

	usb_autopm_put_interface(data->intf);
}

static int btusb_setup_bcm92035(struct hci_dev *hdev)
{
	struct sk_buff *skb;
	u8 val = 0x00;

	BT_DBG("%s", hdev->name);

	skb = __hci_cmd_sync(hdev, 0xfc3b, 1, &val, HCI_INIT_TIMEOUT);
	if (IS_ERR(skb))
		bt_dev_err(hdev, "BCM92035 command failed (%ld)", PTR_ERR(skb));
	else
		kfree_skb(skb);

	return 0;
}

static int btusb_setup_csr(struct hci_dev *hdev)
{
	struct btusb_data *data = hci_get_drvdata(hdev);
	u16 bcdDevice = le16_to_cpu(data->udev->descriptor.bcdDevice);
	struct hci_rp_read_local_version *rp;
	struct sk_buff *skb;
	bool is_fake = false;
	int ret;

	BT_DBG("%s", hdev->name);

	skb = __hci_cmd_sync(hdev, HCI_OP_READ_LOCAL_VERSION, 0, NULL,
			     HCI_INIT_TIMEOUT);
	if (IS_ERR(skb)) {
		int err = PTR_ERR(skb);
		bt_dev_err(hdev, "CSR: Local version failed (%d)", err);
		return err;
	}

	if (skb->len != sizeof(struct hci_rp_read_local_version)) {
		bt_dev_err(hdev, "CSR: Local version length mismatch");
		kfree_skb(skb);
		return -EIO;
	}

	rp = (struct hci_rp_read_local_version *)skb->data;

	/* Detect a wide host of Chinese controllers that aren't CSR.
	 *
	 * Known fake bcdDevices: 0x0100, 0x0134, 0x1915, 0x2520, 0x7558, 0x8891
	 *
	 * The main thing they have in common is that these are really popular low-cost
	 * options that support newer Bluetooth versions but rely on heavy VID/PID
	 * squatting of this poor old Bluetooth 1.1 device. Even sold as such.
	 *
	 * We detect actual CSR devices by checking that the HCI manufacturer code
	 * is Cambridge Silicon Radio (10) and ensuring that LMP sub-version and
	 * HCI rev values always match. As they both store the firmware number.
	 */
	if (le16_to_cpu(rp->manufacturer) != 10 ||
	    le16_to_cpu(rp->hci_rev) != le16_to_cpu(rp->lmp_subver))
		is_fake = true;

	/* Known legit CSR firmware build numbers and their supported BT versions:
	 * - 1.1 (0x1) -> 0x0073, 0x020d, 0x033c, 0x034e
	 * - 1.2 (0x2) ->                 0x04d9, 0x0529
	 * - 2.0 (0x3) ->         0x07a6, 0x07ad, 0x0c5c
	 * - 2.1 (0x4) ->         0x149c, 0x1735, 0x1899 (0x1899 is a BlueCore4-External)
	 * - 4.0 (0x6) ->         0x1d86, 0x2031, 0x22bb
	 *
	 * e.g. Real CSR dongles with LMP subversion 0x73 are old enough that
	 *      support BT 1.1 only; so it's a dead giveaway when some
	 *      third-party BT 4.0 dongle reuses it.
	 */
	else if (le16_to_cpu(rp->lmp_subver) <= 0x034e &&
		 le16_to_cpu(rp->hci_ver) > BLUETOOTH_VER_1_1)
		is_fake = true;

	else if (le16_to_cpu(rp->lmp_subver) <= 0x0529 &&
		 le16_to_cpu(rp->hci_ver) > BLUETOOTH_VER_1_2)
		is_fake = true;

	else if (le16_to_cpu(rp->lmp_subver) <= 0x0c5c &&
		 le16_to_cpu(rp->hci_ver) > BLUETOOTH_VER_2_0)
		is_fake = true;

	else if (le16_to_cpu(rp->lmp_subver) <= 0x1899 &&
		 le16_to_cpu(rp->hci_ver) > BLUETOOTH_VER_2_1)
		is_fake = true;

	else if (le16_to_cpu(rp->lmp_subver) <= 0x22bb &&
		 le16_to_cpu(rp->hci_ver) > BLUETOOTH_VER_4_0)
		is_fake = true;

	/* Other clones which beat all the above checks */
	else if (bcdDevice == 0x0134 &&
		 le16_to_cpu(rp->lmp_subver) == 0x0c5c &&
		 le16_to_cpu(rp->hci_ver) == BLUETOOTH_VER_2_0)
		is_fake = true;

	if (is_fake) {
		bt_dev_warn(hdev, "CSR: Unbranded CSR clone detected; adding workarounds...");

		/* Generally these clones have big discrepancies between
		 * advertised features and what's actually supported.
		 * Probably will need to be expanded in the future;
		 * without these the controller will lock up.
		 */
		set_bit(HCI_QUIRK_BROKEN_STORED_LINK_KEY, &hdev->quirks);
		set_bit(HCI_QUIRK_BROKEN_ERR_DATA_REPORTING, &hdev->quirks);

		/* Clear the reset quirk since this is not an actual
		 * early Bluetooth 1.1 device from CSR.
		 */
		clear_bit(HCI_QUIRK_RESET_ON_CLOSE, &hdev->quirks);
		clear_bit(HCI_QUIRK_SIMULTANEOUS_DISCOVERY, &hdev->quirks);

		/*
		 * Special workaround for clones with a Barrot 8041a02 chip,
		 * these clones are really messed-up:
		 * 1. Their bulk rx endpoint will never report any data unless
		 * the device was suspended at least once (yes really).
		 * 2. They will not wakeup when autosuspended and receiving data
		 * on their bulk rx endpoint from e.g. a keyboard or mouse
		 * (IOW remote-wakeup support is broken for the bulk endpoint).
		 *
		 * To fix 1. enable runtime-suspend, force-suspend the
		 * hci and then wake-it up by disabling runtime-suspend.
		 *
		 * To fix 2. clear the hci's can_wake flag, this way the hci
		 * will still be autosuspended when it is not open.
		 */
		if (bcdDevice == 0x8891 &&
		    le16_to_cpu(rp->lmp_subver) == 0x1012 &&
		    le16_to_cpu(rp->hci_rev) == 0x0810 &&
		    le16_to_cpu(rp->hci_ver) == BLUETOOTH_VER_4_0) {
			bt_dev_warn(hdev, "CSR: detected a fake CSR dongle using a Barrot 8041a02 chip, this chip is very buggy and may have issues");

			pm_runtime_allow(&data->udev->dev);

			ret = pm_runtime_suspend(&data->udev->dev);
			if (ret >= 0)
				msleep(200);
			else
				bt_dev_err(hdev, "Failed to suspend the device for Barrot 8041a02 receive-issue workaround");

			pm_runtime_forbid(&data->udev->dev);

			device_set_wakeup_capable(&data->udev->dev, false);
			/* Re-enable autosuspend if this was requested */
			if (enable_autosuspend)
				usb_enable_autosuspend(data->udev);
		}
	}

	kfree_skb(skb);

	return 0;
}

static const struct firmware *btusb_setup_intel_get_fw(struct hci_dev *hdev,
						       struct intel_version *ver)
{
	const struct firmware *fw;
	char fwname[64];
	int ret;

	snprintf(fwname, sizeof(fwname),
		 "intel/ibt-hw-%x.%x.%x-fw-%x.%x.%x.%x.%x.bseq",
		 ver->hw_platform, ver->hw_variant, ver->hw_revision,
		 ver->fw_variant,  ver->fw_revision, ver->fw_build_num,
		 ver->fw_build_ww, ver->fw_build_yy);

	ret = request_firmware(&fw, fwname, &hdev->dev);
	if (ret < 0) {
		if (ret == -EINVAL) {
			bt_dev_err(hdev, "Intel firmware file request failed (%d)",
				   ret);
			return NULL;
		}

		bt_dev_err(hdev, "failed to open Intel firmware file: %s (%d)",
			   fwname, ret);

		/* If the correct firmware patch file is not found, use the
		 * default firmware patch file instead
		 */
		snprintf(fwname, sizeof(fwname), "intel/ibt-hw-%x.%x.bseq",
			 ver->hw_platform, ver->hw_variant);
		if (request_firmware(&fw, fwname, &hdev->dev) < 0) {
			bt_dev_err(hdev, "failed to open default fw file: %s",
				   fwname);
			return NULL;
		}
	}

	bt_dev_info(hdev, "Intel Bluetooth firmware file: %s", fwname);

	return fw;
}

static int btusb_setup_intel_patching(struct hci_dev *hdev,
				      const struct firmware *fw,
				      const u8 **fw_ptr, int *disable_patch)
{
	struct sk_buff *skb;
	struct hci_command_hdr *cmd;
	const u8 *cmd_param;
	struct hci_event_hdr *evt = NULL;
	const u8 *evt_param = NULL;
	int remain = fw->size - (*fw_ptr - fw->data);

	/* The first byte indicates the types of the patch command or event.
	 * 0x01 means HCI command and 0x02 is HCI event. If the first bytes
	 * in the current firmware buffer doesn't start with 0x01 or
	 * the size of remain buffer is smaller than HCI command header,
	 * the firmware file is corrupted and it should stop the patching
	 * process.
	 */
	if (remain > HCI_COMMAND_HDR_SIZE && *fw_ptr[0] != 0x01) {
		bt_dev_err(hdev, "Intel fw corrupted: invalid cmd read");
		return -EINVAL;
	}
	(*fw_ptr)++;
	remain--;

	cmd = (struct hci_command_hdr *)(*fw_ptr);
	*fw_ptr += sizeof(*cmd);
	remain -= sizeof(*cmd);

	/* Ensure that the remain firmware data is long enough than the length
	 * of command parameter. If not, the firmware file is corrupted.
	 */
	if (remain < cmd->plen) {
		bt_dev_err(hdev, "Intel fw corrupted: invalid cmd len");
		return -EFAULT;
	}

	/* If there is a command that loads a patch in the firmware
	 * file, then enable the patch upon success, otherwise just
	 * disable the manufacturer mode, for example patch activation
	 * is not required when the default firmware patch file is used
	 * because there are no patch data to load.
	 */
	if (*disable_patch && le16_to_cpu(cmd->opcode) == 0xfc8e)
		*disable_patch = 0;

	cmd_param = *fw_ptr;
	*fw_ptr += cmd->plen;
	remain -= cmd->plen;

	/* This reads the expected events when the above command is sent to the
	 * device. Some vendor commands expects more than one events, for
	 * example command status event followed by vendor specific event.
	 * For this case, it only keeps the last expected event. so the command
	 * can be sent with __hci_cmd_sync_ev() which returns the sk_buff of
	 * last expected event.
	 */
	while (remain > HCI_EVENT_HDR_SIZE && *fw_ptr[0] == 0x02) {
		(*fw_ptr)++;
		remain--;

		evt = (struct hci_event_hdr *)(*fw_ptr);
		*fw_ptr += sizeof(*evt);
		remain -= sizeof(*evt);

		if (remain < evt->plen) {
			bt_dev_err(hdev, "Intel fw corrupted: invalid evt len");
			return -EFAULT;
		}

		evt_param = *fw_ptr;
		*fw_ptr += evt->plen;
		remain -= evt->plen;
	}

	/* Every HCI commands in the firmware file has its correspond event.
	 * If event is not found or remain is smaller than zero, the firmware
	 * file is corrupted.
	 */
	if (!evt || !evt_param || remain < 0) {
		bt_dev_err(hdev, "Intel fw corrupted: invalid evt read");
		return -EFAULT;
	}

	skb = __hci_cmd_sync_ev(hdev, le16_to_cpu(cmd->opcode), cmd->plen,
				cmd_param, evt->evt, HCI_INIT_TIMEOUT);
	if (IS_ERR(skb)) {
		bt_dev_err(hdev, "sending Intel patch command (0x%4.4x) failed (%ld)",
			   cmd->opcode, PTR_ERR(skb));
		return PTR_ERR(skb);
	}

	/* It ensures that the returned event matches the event data read from
	 * the firmware file. At fist, it checks the length and then
	 * the contents of the event.
	 */
	if (skb->len != evt->plen) {
		bt_dev_err(hdev, "mismatch event length (opcode 0x%4.4x)",
			   le16_to_cpu(cmd->opcode));
		kfree_skb(skb);
		return -EFAULT;
	}

	if (memcmp(skb->data, evt_param, evt->plen)) {
		bt_dev_err(hdev, "mismatch event parameter (opcode 0x%4.4x)",
			   le16_to_cpu(cmd->opcode));
		kfree_skb(skb);
		return -EFAULT;
	}
	kfree_skb(skb);

	return 0;
}

static int btusb_setup_intel(struct hci_dev *hdev)
{
	struct sk_buff *skb;
	const struct firmware *fw;
	const u8 *fw_ptr;
	int disable_patch, err;
	struct intel_version ver;

	BT_DBG("%s", hdev->name);

	/* The controller has a bug with the first HCI command sent to it
	 * returning number of completed commands as zero. This would stall the
	 * command processing in the Bluetooth core.
	 *
	 * As a workaround, send HCI Reset command first which will reset the
	 * number of completed commands and allow normal command processing
	 * from now on.
	 */
	skb = __hci_cmd_sync(hdev, HCI_OP_RESET, 0, NULL, HCI_INIT_TIMEOUT);
	if (IS_ERR(skb)) {
		bt_dev_err(hdev, "sending initial HCI reset command failed (%ld)",
			   PTR_ERR(skb));
		return PTR_ERR(skb);
	}
	kfree_skb(skb);

	/* Read Intel specific controller version first to allow selection of
	 * which firmware file to load.
	 *
	 * The returned information are hardware variant and revision plus
	 * firmware variant, revision and build number.
	 */
	err = btintel_read_version(hdev, &ver);
	if (err)
		return err;

	bt_dev_info(hdev, "read Intel version: %02x%02x%02x%02x%02x%02x%02x%02x%02x",
		    ver.hw_platform, ver.hw_variant, ver.hw_revision,
		    ver.fw_variant,  ver.fw_revision, ver.fw_build_num,
		    ver.fw_build_ww, ver.fw_build_yy, ver.fw_patch_num);

	/* fw_patch_num indicates the version of patch the device currently
	 * have. If there is no patch data in the device, it is always 0x00.
	 * So, if it is other than 0x00, no need to patch the device again.
	 */
	if (ver.fw_patch_num) {
		bt_dev_info(hdev, "Intel device is already patched. "
			    "patch num: %02x", ver.fw_patch_num);
		goto complete;
	}

	/* Opens the firmware patch file based on the firmware version read
	 * from the controller. If it fails to open the matching firmware
	 * patch file, it tries to open the default firmware patch file.
	 * If no patch file is found, allow the device to operate without
	 * a patch.
	 */
	fw = btusb_setup_intel_get_fw(hdev, &ver);
	if (!fw)
		goto complete;
	fw_ptr = fw->data;

	/* Enable the manufacturer mode of the controller.
	 * Only while this mode is enabled, the driver can download the
	 * firmware patch data and configuration parameters.
	 */
	err = btintel_enter_mfg(hdev);
	if (err) {
		release_firmware(fw);
		return err;
	}

	disable_patch = 1;

	/* The firmware data file consists of list of Intel specific HCI
	 * commands and its expected events. The first byte indicates the
	 * type of the message, either HCI command or HCI event.
	 *
	 * It reads the command and its expected event from the firmware file,
	 * and send to the controller. Once __hci_cmd_sync_ev() returns,
	 * the returned event is compared with the event read from the firmware
	 * file and it will continue until all the messages are downloaded to
	 * the controller.
	 *
	 * Once the firmware patching is completed successfully,
	 * the manufacturer mode is disabled with reset and activating the
	 * downloaded patch.
	 *
	 * If the firmware patching fails, the manufacturer mode is
	 * disabled with reset and deactivating the patch.
	 *
	 * If the default patch file is used, no reset is done when disabling
	 * the manufacturer.
	 */
	while (fw->size > fw_ptr - fw->data) {
		int ret;

		ret = btusb_setup_intel_patching(hdev, fw, &fw_ptr,
						 &disable_patch);
		if (ret < 0)
			goto exit_mfg_deactivate;
	}

	release_firmware(fw);

	if (disable_patch)
		goto exit_mfg_disable;

	/* Patching completed successfully and disable the manufacturer mode
	 * with reset and activate the downloaded firmware patches.
	 */
	err = btintel_exit_mfg(hdev, true, true);
	if (err)
		return err;

	/* Need build number for downloaded fw patches in
	 * every power-on boot
	 */
       err = btintel_read_version(hdev, &ver);
       if (err)
               return err;
       bt_dev_info(hdev, "Intel BT fw patch 0x%02x completed & activated",
		   ver.fw_patch_num);

	goto complete;

exit_mfg_disable:
	/* Disable the manufacturer mode without reset */
	err = btintel_exit_mfg(hdev, false, false);
	if (err)
		return err;

	bt_dev_info(hdev, "Intel firmware patch completed");

	goto complete;

exit_mfg_deactivate:
	release_firmware(fw);

	/* Patching failed. Disable the manufacturer mode with reset and
	 * deactivate the downloaded firmware patches.
	 */
	err = btintel_exit_mfg(hdev, true, false);
	if (err)
		return err;

	bt_dev_info(hdev, "Intel firmware patch completed and deactivated");

complete:
	/* Set the event mask for Intel specific vendor events. This enables
	 * a few extra events that are useful during general operation.
	 */
	btintel_set_event_mask_mfg(hdev, false);

	btintel_check_bdaddr(hdev);
	return 0;
}

static int inject_cmd_complete(struct hci_dev *hdev, __u16 opcode)
{
	struct sk_buff *skb;
	struct hci_event_hdr *hdr;
	struct hci_ev_cmd_complete *evt;

	skb = bt_skb_alloc(sizeof(*hdr) + sizeof(*evt) + 1, GFP_KERNEL);
	if (!skb)
		return -ENOMEM;

	hdr = skb_put(skb, sizeof(*hdr));
	hdr->evt = HCI_EV_CMD_COMPLETE;
	hdr->plen = sizeof(*evt) + 1;

	evt = skb_put(skb, sizeof(*evt));
	evt->ncmd = 0x01;
	evt->opcode = cpu_to_le16(opcode);

	skb_put_u8(skb, 0x00);

	hci_skb_pkt_type(skb) = HCI_EVENT_PKT;

	return hci_recv_frame(hdev, skb);
}

static int btusb_recv_bulk_intel(struct btusb_data *data, void *buffer,
				 int count)
{
	/* When the device is in bootloader mode, then it can send
	 * events via the bulk endpoint. These events are treated the
	 * same way as the ones received from the interrupt endpoint.
	 */
	if (test_bit(BTUSB_BOOTLOADER, &data->flags))
		return btusb_recv_intr(data, buffer, count);

	return btusb_recv_bulk(data, buffer, count);
}

static void btusb_intel_bootup(struct btusb_data *data, const void *ptr,
			       unsigned int len)
{
	const struct intel_bootup *evt = ptr;

	if (len != sizeof(*evt))
		return;

	if (test_and_clear_bit(BTUSB_BOOTING, &data->flags))
		wake_up_bit(&data->flags, BTUSB_BOOTING);
}

static void btusb_intel_secure_send_result(struct btusb_data *data,
					   const void *ptr, unsigned int len)
{
	const struct intel_secure_send_result *evt = ptr;

	if (len != sizeof(*evt))
		return;

	if (evt->result)
		set_bit(BTUSB_FIRMWARE_FAILED, &data->flags);

	if (test_and_clear_bit(BTUSB_DOWNLOADING, &data->flags) &&
	    test_bit(BTUSB_FIRMWARE_LOADED, &data->flags))
		wake_up_bit(&data->flags, BTUSB_DOWNLOADING);
}

static int btusb_recv_event_intel(struct hci_dev *hdev, struct sk_buff *skb)
{
	struct btusb_data *data = hci_get_drvdata(hdev);

	if (test_bit(BTUSB_BOOTLOADER, &data->flags)) {
		struct hci_event_hdr *hdr = (void *)skb->data;

		if (skb->len > HCI_EVENT_HDR_SIZE && hdr->evt == 0xff &&
		    hdr->plen > 0) {
			const void *ptr = skb->data + HCI_EVENT_HDR_SIZE + 1;
			unsigned int len = skb->len - HCI_EVENT_HDR_SIZE - 1;

			switch (skb->data[2]) {
			case 0x02:
				/* When switching to the operational firmware
				 * the device sends a vendor specific event
				 * indicating that the bootup completed.
				 */
				btusb_intel_bootup(data, ptr, len);
				break;
			case 0x06:
				/* When the firmware loading completes the
				 * device sends out a vendor specific event
				 * indicating the result of the firmware
				 * loading.
				 */
				btusb_intel_secure_send_result(data, ptr, len);
				break;
			}
		}
	}

	return hci_recv_frame(hdev, skb);
}

static int btusb_send_frame_intel(struct hci_dev *hdev, struct sk_buff *skb)
{
	struct btusb_data *data = hci_get_drvdata(hdev);
	struct urb *urb;

	BT_DBG("%s", hdev->name);

	switch (hci_skb_pkt_type(skb)) {
	case HCI_COMMAND_PKT:
		if (test_bit(BTUSB_BOOTLOADER, &data->flags)) {
			struct hci_command_hdr *cmd = (void *)skb->data;
			__u16 opcode = le16_to_cpu(cmd->opcode);

			/* When in bootloader mode and the command 0xfc09
			 * is received, it needs to be send down the
			 * bulk endpoint. So allocate a bulk URB instead.
			 */
			if (opcode == 0xfc09)
				urb = alloc_bulk_urb(hdev, skb);
			else
				urb = alloc_ctrl_urb(hdev, skb);

			/* When the 0xfc01 command is issued to boot into
			 * the operational firmware, it will actually not
			 * send a command complete event. To keep the flow
			 * control working inject that event here.
			 */
			if (opcode == 0xfc01)
				inject_cmd_complete(hdev, opcode);
		} else {
			urb = alloc_ctrl_urb(hdev, skb);
		}
		if (IS_ERR(urb))
			return PTR_ERR(urb);

		hdev->stat.cmd_tx++;
		return submit_or_queue_tx_urb(hdev, urb);

	case HCI_ACLDATA_PKT:
		urb = alloc_bulk_urb(hdev, skb);
		if (IS_ERR(urb))
			return PTR_ERR(urb);

		hdev->stat.acl_tx++;
		return submit_or_queue_tx_urb(hdev, urb);

	case HCI_SCODATA_PKT:
		if (hci_conn_num(hdev, SCO_LINK) < 1)
			return -ENODEV;

		urb = alloc_isoc_urb(hdev, skb);
		if (IS_ERR(urb))
			return PTR_ERR(urb);

		hdev->stat.sco_tx++;
		return submit_tx_urb(hdev, urb);
	}

	return -EILSEQ;
}

static bool btusb_setup_intel_new_get_fw_name(struct intel_version *ver,
					     struct intel_boot_params *params,
					     char *fw_name, size_t len,
					     const char *suffix)
{
	switch (ver->hw_variant) {
	case 0x0b:	/* SfP */
	case 0x0c:	/* WsP */
		snprintf(fw_name, len, "intel/ibt-%u-%u.%s",
			le16_to_cpu(ver->hw_variant),
			le16_to_cpu(params->dev_revid),
			suffix);
		break;
	case 0x11:	/* JfP */
	case 0x12:	/* ThP */
	case 0x13:	/* HrP */
	case 0x14:	/* CcP */
		snprintf(fw_name, len, "intel/ibt-%u-%u-%u.%s",
			le16_to_cpu(ver->hw_variant),
			le16_to_cpu(ver->hw_revision),
			le16_to_cpu(ver->fw_revision),
			suffix);
		break;
	default:
		return false;
	}
	return true;
}

static void btusb_setup_intel_newgen_get_fw_name(const struct intel_version_tlv *ver_tlv,
						 char *fw_name, size_t len,
						 const char *suffix)
{
	/* The firmware file name for new generation controllers will be
	 * ibt-<cnvi_top type+cnvi_top step>-<cnvr_top type+cnvr_top step>
	 */
	snprintf(fw_name, len, "intel/ibt-%04x-%04x.%s",
		 INTEL_CNVX_TOP_PACK_SWAB(INTEL_CNVX_TOP_TYPE(ver_tlv->cnvi_top),
					  INTEL_CNVX_TOP_STEP(ver_tlv->cnvi_top)),
		 INTEL_CNVX_TOP_PACK_SWAB(INTEL_CNVX_TOP_TYPE(ver_tlv->cnvr_top),
					  INTEL_CNVX_TOP_STEP(ver_tlv->cnvr_top)),
		 suffix);
}

static int btusb_intel_download_firmware_newgen(struct hci_dev *hdev,
						struct intel_version_tlv *ver,
						u32 *boot_param)
{
	const struct firmware *fw;
	char fwname[64];
	int err;
	struct btusb_data *data = hci_get_drvdata(hdev);

	if (!ver || !boot_param)
		return -EINVAL;

	/* The hardware platform number has a fixed value of 0x37 and
	 * for now only accept this single value.
	 */
	if (INTEL_HW_PLATFORM(ver->cnvi_bt) != 0x37) {
		bt_dev_err(hdev, "Unsupported Intel hardware platform (0x%2x)",
			   INTEL_HW_PLATFORM(ver->cnvi_bt));
		return -EINVAL;
	}

	/* The firmware variant determines if the device is in bootloader
	 * mode or is running operational firmware. The value 0x03 identifies
	 * the bootloader and the value 0x23 identifies the operational
	 * firmware.
	 *
	 * When the operational firmware is already present, then only
	 * the check for valid Bluetooth device address is needed. This
	 * determines if the device will be added as configured or
	 * unconfigured controller.
	 *
	 * It is not possible to use the Secure Boot Parameters in this
	 * case since that command is only available in bootloader mode.
	 */
	if (ver->img_type == 0x03) {
		clear_bit(BTUSB_BOOTLOADER, &data->flags);
		btintel_check_bdaddr(hdev);
		return 0;
	}

	/* Check for supported iBT hardware variants of this firmware
	 * loading method.
	 *
	 * This check has been put in place to ensure correct forward
	 * compatibility options when newer hardware variants come along.
	 */
	switch (INTEL_HW_VARIANT(ver->cnvi_bt)) {
	case 0x17:	/* TyP */
	case 0x18:	/* Slr */
	case 0x19:	/* Slr-F */
		break;
	default:
		bt_dev_err(hdev, "Unsupported Intel hardware variant (0x%x)",
			   INTEL_HW_VARIANT(ver->cnvi_bt));
		return -EINVAL;
	}

	/* If the device is not in bootloader mode, then the only possible
	 * choice is to return an error and abort the device initialization.
	 */
	if (ver->img_type != 0x01) {
		bt_dev_err(hdev, "Unsupported Intel firmware variant (0x%x)",
			   ver->img_type);
		return -ENODEV;
	}

	/* It is required that every single firmware fragment is acknowledged
	 * with a command complete event. If the boot parameters indicate
	 * that this bootloader does not send them, then abort the setup.
	 */
	if (ver->limited_cce != 0x00) {
		bt_dev_err(hdev, "Unsupported Intel firmware loading method (0x%x)",
			   ver->limited_cce);
		return -EINVAL;
	}

	/* Secure boot engine type should be either 1 (ECDSA) or 0 (RSA) */
	if (ver->sbe_type > 0x01) {
		bt_dev_err(hdev, "Unsupported Intel secure boot engine type (0x%x)",
			   ver->sbe_type);
		return -EINVAL;
	}

	/* If the OTP has no valid Bluetooth device address, then there will
	 * also be no valid address for the operational firmware.
	 */
	if (!bacmp(&ver->otp_bd_addr, BDADDR_ANY)) {
		bt_dev_info(hdev, "No device address configured");
		set_bit(HCI_QUIRK_INVALID_BDADDR, &hdev->quirks);
	}

	btusb_setup_intel_newgen_get_fw_name(ver, fwname, sizeof(fwname), "sfi");
	err = request_firmware(&fw, fwname, &hdev->dev);
	if (err < 0) {
		bt_dev_err(hdev, "Failed to load Intel firmware file %s (%d)",
			   fwname, err);
		return err;
	}

	bt_dev_info(hdev, "Found device firmware: %s", fwname);

	if (fw->size < 644) {
		bt_dev_err(hdev, "Invalid size of firmware file (%zu)",
			   fw->size);
		err = -EBADF;
		goto done;
	}

	set_bit(BTUSB_DOWNLOADING, &data->flags);

	/* Start firmware downloading and get boot parameter */
	err = btintel_download_firmware_newgen(hdev, ver, fw, boot_param,
					       INTEL_HW_VARIANT(ver->cnvi_bt),
					       ver->sbe_type);
	if (err < 0) {
		if (err == -EALREADY) {
			/* Firmware has already been loaded */
			set_bit(BTUSB_FIRMWARE_LOADED, &data->flags);
			err = 0;
			goto done;
		}

		/* When FW download fails, send Intel Reset to retry
		 * FW download.
		 */
		btintel_reset_to_bootloader(hdev);
		goto done;
	}
	set_bit(BTUSB_FIRMWARE_LOADED, &data->flags);

	bt_dev_info(hdev, "Waiting for firmware download to complete");

	/* Before switching the device into operational mode and with that
	 * booting the loaded firmware, wait for the bootloader notification
	 * that all fragments have been successfully received.
	 *
	 * When the event processing receives the notification, then the
	 * BTUSB_DOWNLOADING flag will be cleared.
	 *
	 * The firmware loading should not take longer than 5 seconds
	 * and thus just timeout if that happens and fail the setup
	 * of this device.
	 */
	err = wait_on_bit_timeout(&data->flags, BTUSB_DOWNLOADING,
				  TASK_INTERRUPTIBLE,
				  msecs_to_jiffies(5000));
	if (err == -EINTR) {
		bt_dev_err(hdev, "Firmware loading interrupted");
		goto done;
	}

	if (err) {
		bt_dev_err(hdev, "Firmware loading timeout");
		err = -ETIMEDOUT;
		btintel_reset_to_bootloader(hdev);
		goto done;
	}

	if (test_bit(BTUSB_FIRMWARE_FAILED, &data->flags)) {
		bt_dev_err(hdev, "Firmware loading failed");
		err = -ENOEXEC;
		goto done;
	}

done:
	release_firmware(fw);
	return err;
}

static int btusb_intel_download_firmware(struct hci_dev *hdev,
					 struct intel_version *ver,
					 struct intel_boot_params *params,
					 u32 *boot_param)
{
	const struct firmware *fw;
	char fwname[64];
	int err;
	struct btusb_data *data = hci_get_drvdata(hdev);

	if (!ver || !params)
		return -EINVAL;

	/* The hardware platform number has a fixed value of 0x37 and
	 * for now only accept this single value.
	 */
	if (ver->hw_platform != 0x37) {
		bt_dev_err(hdev, "Unsupported Intel hardware platform (%u)",
			   ver->hw_platform);
		return -EINVAL;
	}

	/* Check for supported iBT hardware variants of this firmware
	 * loading method.
	 *
	 * This check has been put in place to ensure correct forward
	 * compatibility options when newer hardware variants come along.
	 */
	switch (ver->hw_variant) {
	case 0x0b:	/* SfP */
	case 0x0c:	/* WsP */
	case 0x11:	/* JfP */
	case 0x12:	/* ThP */
	case 0x13:	/* HrP */
	case 0x14:	/* CcP */
		break;
	default:
		bt_dev_err(hdev, "Unsupported Intel hardware variant (%u)",
			   ver->hw_variant);
		return -EINVAL;
	}

	btintel_version_info(hdev, ver);

	/* The firmware variant determines if the device is in bootloader
	 * mode or is running operational firmware. The value 0x06 identifies
	 * the bootloader and the value 0x23 identifies the operational
	 * firmware.
	 *
	 * When the operational firmware is already present, then only
	 * the check for valid Bluetooth device address is needed. This
	 * determines if the device will be added as configured or
	 * unconfigured controller.
	 *
	 * It is not possible to use the Secure Boot Parameters in this
	 * case since that command is only available in bootloader mode.
	 */
	if (ver->fw_variant == 0x23) {
		clear_bit(BTUSB_BOOTLOADER, &data->flags);
		btintel_check_bdaddr(hdev);
		return 0;
	}

	/* If the device is not in bootloader mode, then the only possible
	 * choice is to return an error and abort the device initialization.
	 */
	if (ver->fw_variant != 0x06) {
		bt_dev_err(hdev, "Unsupported Intel firmware variant (%u)",
			   ver->fw_variant);
		return -ENODEV;
	}

	/* Read the secure boot parameters to identify the operating
	 * details of the bootloader.
	 */
	err = btintel_read_boot_params(hdev, params);
	if (err)
		return err;

	/* It is required that every single firmware fragment is acknowledged
	 * with a command complete event. If the boot parameters indicate
	 * that this bootloader does not send them, then abort the setup.
	 */
	if (params->limited_cce != 0x00) {
		bt_dev_err(hdev, "Unsupported Intel firmware loading method (%u)",
			   params->limited_cce);
		return -EINVAL;
	}

	/* If the OTP has no valid Bluetooth device address, then there will
	 * also be no valid address for the operational firmware.
	 */
	if (!bacmp(&params->otp_bdaddr, BDADDR_ANY)) {
		bt_dev_info(hdev, "No device address configured");
		set_bit(HCI_QUIRK_INVALID_BDADDR, &hdev->quirks);
	}

	/* With this Intel bootloader only the hardware variant and device
	 * revision information are used to select the right firmware for SfP
	 * and WsP.
	 *
	 * The firmware filename is ibt-<hw_variant>-<dev_revid>.sfi.
	 *
	 * Currently the supported hardware variants are:
	 *   11 (0x0b) for iBT3.0 (LnP/SfP)
	 *   12 (0x0c) for iBT3.5 (WsP)
	 *
	 * For ThP/JfP and for future SKU's, the FW name varies based on HW
	 * variant, HW revision and FW revision, as these are dependent on CNVi
	 * and RF Combination.
	 *
	 *   17 (0x11) for iBT3.5 (JfP)
	 *   18 (0x12) for iBT3.5 (ThP)
	 *
	 * The firmware file name for these will be
	 * ibt-<hw_variant>-<hw_revision>-<fw_revision>.sfi.
	 *
	 */
	err = btusb_setup_intel_new_get_fw_name(ver, params, fwname,
						sizeof(fwname), "sfi");
	if (!err) {
		bt_dev_err(hdev, "Unsupported Intel firmware naming");
		return -EINVAL;
	}

	err = request_firmware(&fw, fwname, &hdev->dev);
	if (err < 0) {
		bt_dev_err(hdev, "Failed to load Intel firmware file %s (%d)",
			   fwname, err);
		return err;
	}

	bt_dev_info(hdev, "Found device firmware: %s", fwname);

	if (fw->size < 644) {
		bt_dev_err(hdev, "Invalid size of firmware file (%zu)",
			   fw->size);
		err = -EBADF;
		goto done;
	}

	set_bit(BTUSB_DOWNLOADING, &data->flags);

	/* Start firmware downloading and get boot parameter */
	err = btintel_download_firmware(hdev, ver, fw, boot_param);
	if (err < 0) {
		if (err == -EALREADY) {
			/* Firmware has already been loaded */
			set_bit(BTUSB_FIRMWARE_LOADED, &data->flags);
			err = 0;
			goto done;
		}

		/* When FW download fails, send Intel Reset to retry
		 * FW download.
		 */
		btintel_reset_to_bootloader(hdev);
		goto done;
	}
	set_bit(BTUSB_FIRMWARE_LOADED, &data->flags);

	bt_dev_info(hdev, "Waiting for firmware download to complete");

	/* Before switching the device into operational mode and with that
	 * booting the loaded firmware, wait for the bootloader notification
	 * that all fragments have been successfully received.
	 *
	 * When the event processing receives the notification, then the
	 * BTUSB_DOWNLOADING flag will be cleared.
	 *
	 * The firmware loading should not take longer than 5 seconds
	 * and thus just timeout if that happens and fail the setup
	 * of this device.
	 */
	err = wait_on_bit_timeout(&data->flags, BTUSB_DOWNLOADING,
				  TASK_INTERRUPTIBLE,
				  msecs_to_jiffies(5000));
	if (err == -EINTR) {
		bt_dev_err(hdev, "Firmware loading interrupted");
		goto done;
	}

	if (err) {
		bt_dev_err(hdev, "Firmware loading timeout");
		err = -ETIMEDOUT;
		btintel_reset_to_bootloader(hdev);
		goto done;
	}

	if (test_bit(BTUSB_FIRMWARE_FAILED, &data->flags)) {
		bt_dev_err(hdev, "Firmware loading failed");
		err = -ENOEXEC;
		goto done;
	}

done:
	release_firmware(fw);
	return err;
}

static int btusb_setup_intel_new(struct hci_dev *hdev)
{
	struct btusb_data *data = hci_get_drvdata(hdev);
	struct intel_version ver;
	struct intel_boot_params params;
	u32 boot_param;
	char ddcname[64];
	ktime_t calltime, delta, rettime;
	unsigned long long duration;
	int err;
	struct intel_debug_features features;

	BT_DBG("%s", hdev->name);

	/* Set the default boot parameter to 0x0 and it is updated to
	 * SKU specific boot parameter after reading Intel_Write_Boot_Params
	 * command while downloading the firmware.
	 */
	boot_param = 0x00000000;

	calltime = ktime_get();

	/* Read the Intel version information to determine if the device
	 * is in bootloader mode or if it already has operational firmware
	 * loaded.
	 */
	err = btintel_read_version(hdev, &ver);
	if (err) {
		bt_dev_err(hdev, "Intel Read version failed (%d)", err);
		btintel_reset_to_bootloader(hdev);
		return err;
	}

	err = btusb_intel_download_firmware(hdev, &ver, &params, &boot_param);
	if (err)
		return err;

	/* controller is already having an operational firmware */
	if (ver.fw_variant == 0x23)
		goto finish;

	rettime = ktime_get();
	delta = ktime_sub(rettime, calltime);
	duration = (unsigned long long) ktime_to_ns(delta) >> 10;

	bt_dev_info(hdev, "Firmware loaded in %llu usecs", duration);

	calltime = ktime_get();

	set_bit(BTUSB_BOOTING, &data->flags);

	err = btintel_send_intel_reset(hdev, boot_param);
	if (err) {
		bt_dev_err(hdev, "Intel Soft Reset failed (%d)", err);
		btintel_reset_to_bootloader(hdev);
		return err;
	}

	/* The bootloader will not indicate when the device is ready. This
	 * is done by the operational firmware sending bootup notification.
	 *
	 * Booting into operational firmware should not take longer than
	 * 1 second. However if that happens, then just fail the setup
	 * since something went wrong.
	 */
	bt_dev_info(hdev, "Waiting for device to boot");

	err = wait_on_bit_timeout(&data->flags, BTUSB_BOOTING,
				  TASK_INTERRUPTIBLE,
				  msecs_to_jiffies(1000));

	if (err == -EINTR) {
		bt_dev_err(hdev, "Device boot interrupted");
		return -EINTR;
	}

	if (err) {
		bt_dev_err(hdev, "Device boot timeout");
		btintel_reset_to_bootloader(hdev);
		return -ETIMEDOUT;
	}

	rettime = ktime_get();
	delta = ktime_sub(rettime, calltime);
	duration = (unsigned long long) ktime_to_ns(delta) >> 10;

	bt_dev_info(hdev, "Device booted in %llu usecs", duration);

	clear_bit(BTUSB_BOOTLOADER, &data->flags);

	err = btusb_setup_intel_new_get_fw_name(&ver, &params, ddcname,
						sizeof(ddcname), "ddc");

	if (!err) {
		bt_dev_err(hdev, "Unsupported Intel firmware naming");
	} else {
		/* Once the device is running in operational mode, it needs to
		 * apply the device configuration (DDC) parameters.
		 *
		 * The device can work without DDC parameters, so even if it
		 * fails to load the file, no need to fail the setup.
		 */
		btintel_load_ddc_config(hdev, ddcname);
	}

	/* Read the Intel supported features and if new exception formats
	 * supported, need to load the additional DDC config to enable.
	 */
	btintel_read_debug_features(hdev, &features);

	/* Set DDC mask for available debug features */
	btintel_set_debug_features(hdev, &features);

	/* Read the Intel version information after loading the FW  */
	err = btintel_read_version(hdev, &ver);
	if (err)
		return err;

	btintel_version_info(hdev, &ver);

finish:
	/* All Intel controllers that support the Microsoft vendor
	 * extension are using 0xFC1E for VsMsftOpCode.
	 */
	switch (ver.hw_variant) {
	case 0x11:	/* JfP */
	case 0x12:	/* ThP */
	case 0x13:	/* HrP */
	case 0x14:	/* CcP */
		hci_set_msft_opcode(hdev, 0xFC1E);
		break;
	}

	/* Set the event mask for Intel specific vendor events. This enables
	 * a few extra events that are useful during general operation. It
	 * does not enable any debugging related events.
	 *
	 * The device will function correctly without these events enabled
	 * and thus no need to fail the setup.
	 */
	btintel_set_event_mask(hdev, false);

	return 0;
}

static int btusb_setup_intel_newgen(struct hci_dev *hdev)
{
	struct btusb_data *data = hci_get_drvdata(hdev);
	u32 boot_param;
	char ddcname[64];
	ktime_t calltime, delta, rettime;
	unsigned long long duration;
	int err;
	struct intel_debug_features features;
	struct intel_version_tlv version;

	bt_dev_dbg(hdev, "");

	/* Set the default boot parameter to 0x0 and it is updated to
	 * SKU specific boot parameter after reading Intel_Write_Boot_Params
	 * command while downloading the firmware.
	 */
	boot_param = 0x00000000;

	calltime = ktime_get();

	/* Read the Intel version information to determine if the device
	 * is in bootloader mode or if it already has operational firmware
	 * loaded.
	 */
	err = btintel_read_version_tlv(hdev, &version);
	if (err) {
		bt_dev_err(hdev, "Intel Read version failed (%d)", err);
		btintel_reset_to_bootloader(hdev);
		return err;
	}

	btintel_version_info_tlv(hdev, &version);

	err = btusb_intel_download_firmware_newgen(hdev, &version, &boot_param);
	if (err)
		return err;

	/* check if controller is already having an operational firmware */
	if (version.img_type == 0x03)
		goto finish;

	rettime = ktime_get();
	delta = ktime_sub(rettime, calltime);
	duration = (unsigned long long)ktime_to_ns(delta) >> 10;

	bt_dev_info(hdev, "Firmware loaded in %llu usecs", duration);

	calltime = ktime_get();

	set_bit(BTUSB_BOOTING, &data->flags);

	err = btintel_send_intel_reset(hdev, boot_param);
	if (err) {
		bt_dev_err(hdev, "Intel Soft Reset failed (%d)", err);
		btintel_reset_to_bootloader(hdev);
		return err;
	}

	/* The bootloader will not indicate when the device is ready. This
	 * is done by the operational firmware sending bootup notification.
	 *
	 * Booting into operational firmware should not take longer than
	 * 1 second. However if that happens, then just fail the setup
	 * since something went wrong.
	 */
	bt_dev_info(hdev, "Waiting for device to boot");

	err = wait_on_bit_timeout(&data->flags, BTUSB_BOOTING,
				  TASK_INTERRUPTIBLE,
				  msecs_to_jiffies(1000));

	if (err == -EINTR) {
		bt_dev_err(hdev, "Device boot interrupted");
		return -EINTR;
	}

	if (err) {
		bt_dev_err(hdev, "Device boot timeout");
		btintel_reset_to_bootloader(hdev);
		return -ETIMEDOUT;
	}

	rettime = ktime_get();
	delta = ktime_sub(rettime, calltime);
	duration = (unsigned long long)ktime_to_ns(delta) >> 10;

	bt_dev_info(hdev, "Device booted in %llu usecs", duration);

	clear_bit(BTUSB_BOOTLOADER, &data->flags);

	btusb_setup_intel_newgen_get_fw_name(&version, ddcname, sizeof(ddcname),
					     "ddc");
	/* Once the device is running in operational mode, it needs to
	 * apply the device configuration (DDC) parameters.
	 *
	 * The device can work without DDC parameters, so even if it
	 * fails to load the file, no need to fail the setup.
	 */
	btintel_load_ddc_config(hdev, ddcname);

	/* Read the Intel supported features and if new exception formats
	 * supported, need to load the additional DDC config to enable.
	 */
	btintel_read_debug_features(hdev, &features);

	/* Set DDC mask for available debug features */
	btintel_set_debug_features(hdev, &features);

	/* Read the Intel version information after loading the FW  */
	err = btintel_read_version_tlv(hdev, &version);
	if (err)
		return err;

	btintel_version_info_tlv(hdev, &version);

finish:
	/* Set the event mask for Intel specific vendor events. This enables
	 * a few extra events that are useful during general operation. It
	 * does not enable any debugging related events.
	 *
	 * The device will function correctly without these events enabled
	 * and thus no need to fail the setup.
	 */
	btintel_set_event_mask(hdev, false);

	return 0;
}
static int btusb_shutdown_intel(struct hci_dev *hdev)
{
	struct sk_buff *skb;
	long ret;

	/* In the shutdown sequence where Bluetooth is turned off followed
	 * by WiFi being turned off, turning WiFi back on causes issue with
	 * the RF calibration.
	 *
	 * To ensure that any RF activity has been stopped, issue HCI Reset
	 * command to clear all ongoing activity including advertising,
	 * scanning etc.
	 */
	skb = __hci_cmd_sync(hdev, HCI_OP_RESET, 0, NULL, HCI_INIT_TIMEOUT);
	if (IS_ERR(skb)) {
		ret = PTR_ERR(skb);
		bt_dev_err(hdev, "HCI reset during shutdown failed");
		return ret;
	}
	kfree_skb(skb);

	/* Some platforms have an issue with BT LED when the interface is
	 * down or BT radio is turned off, which takes 5 seconds to BT LED
	 * goes off. This command turns off the BT LED immediately.
	 */
	skb = __hci_cmd_sync(hdev, 0xfc3f, 0, NULL, HCI_INIT_TIMEOUT);
	if (IS_ERR(skb)) {
		ret = PTR_ERR(skb);
		bt_dev_err(hdev, "turning off Intel device LED failed");
		return ret;
	}
	kfree_skb(skb);

	return 0;
}

static int btusb_shutdown_intel_new(struct hci_dev *hdev)
{
	struct sk_buff *skb;

	/* Send HCI Reset to the controller to stop any BT activity which
	 * were triggered. This will help to save power and maintain the
	 * sync b/w Host and controller
	 */
	skb = __hci_cmd_sync(hdev, HCI_OP_RESET, 0, NULL, HCI_INIT_TIMEOUT);
	if (IS_ERR(skb)) {
		bt_dev_err(hdev, "HCI reset during shutdown failed");
		return PTR_ERR(skb);
	}
	kfree_skb(skb);

	return 0;
}

#define FIRMWARE_MT7663		"mediatek/mt7663pr2h.bin"
#define FIRMWARE_MT7668		"mediatek/mt7668pr2h.bin"

#define HCI_WMT_MAX_EVENT_SIZE		64
/* It is for mt79xx download rom patch*/
#define MTK_FW_ROM_PATCH_HEADER_SIZE	32
#define MTK_FW_ROM_PATCH_GD_SIZE	64
#define MTK_FW_ROM_PATCH_SEC_MAP_SIZE	64
#define MTK_SEC_MAP_COMMON_SIZE	12
#define MTK_SEC_MAP_NEED_SEND_SIZE	52

enum {
	BTMTK_WMT_PATCH_DWNLD = 0x1,
	BTMTK_WMT_FUNC_CTRL = 0x6,
	BTMTK_WMT_RST = 0x7,
	BTMTK_WMT_SEMAPHORE = 0x17,
};

enum {
	BTMTK_WMT_INVALID,
	BTMTK_WMT_PATCH_UNDONE,
	BTMTK_WMT_PATCH_PROGRESS,
	BTMTK_WMT_PATCH_DONE,
	BTMTK_WMT_ON_UNDONE,
	BTMTK_WMT_ON_DONE,
	BTMTK_WMT_ON_PROGRESS,
};

struct btmtk_wmt_hdr {
	u8	dir;
	u8	op;
	__le16	dlen;
	u8	flag;
} __packed;

struct btmtk_hci_wmt_cmd {
	struct btmtk_wmt_hdr hdr;
	u8 data[];
} __packed;

struct btmtk_hci_wmt_evt {
	struct hci_event_hdr hhdr;
	struct btmtk_wmt_hdr whdr;
} __packed;

struct btmtk_hci_wmt_evt_funcc {
	struct btmtk_hci_wmt_evt hwhdr;
	__be16 status;
} __packed;

struct btmtk_tci_sleep {
	u8 mode;
	__le16 duration;
	__le16 host_duration;
	u8 host_wakeup_pin;
	u8 time_compensation;
} __packed;

struct btmtk_hci_wmt_params {
	u8 op;
	u8 flag;
	u16 dlen;
	const void *data;
	u32 *status;
};

struct btmtk_patch_header {
	u8 datetime[16];
	u8 platform[4];
	__le16 hwver;
	__le16 swver;
	__le32 magicnum;
} __packed;

struct btmtk_global_desc {
	__le32 patch_ver;
	__le32 sub_sys;
	__le32 feature_opt;
	__le32 section_num;
} __packed;

struct btmtk_section_map {
	__le32 sectype;
	__le32 secoffset;
	__le32 secsize;
	union {
		__le32 u4SecSpec[13];
		struct {
			__le32 dlAddr;
			__le32 dlsize;
			__le32 seckeyidx;
			__le32 alignlen;
			__le32 sectype;
			__le32 dlmodecrctype;
			__le32 crc;
			__le32 reserved[6];
		} bin_info_spec;
	};
} __packed;

static void btusb_mtk_wmt_recv(struct urb *urb)
{
	struct hci_dev *hdev = urb->context;
	struct btusb_data *data = hci_get_drvdata(hdev);
	struct hci_event_hdr *hdr;
	struct sk_buff *skb;
	int err;

	if (urb->status == 0 && urb->actual_length > 0) {
		hdev->stat.byte_rx += urb->actual_length;

		/* WMT event shouldn't be fragmented and the size should be
		 * less than HCI_WMT_MAX_EVENT_SIZE.
		 */
		skb = bt_skb_alloc(HCI_WMT_MAX_EVENT_SIZE, GFP_ATOMIC);
		if (!skb) {
			hdev->stat.err_rx++;
			return;
		}

		hci_skb_pkt_type(skb) = HCI_EVENT_PKT;
		skb_put_data(skb, urb->transfer_buffer, urb->actual_length);

		hdr = (void *)skb->data;
		/* Fix up the vendor event id with 0xff for vendor specific
		 * instead of 0xe4 so that event send via monitoring socket can
		 * be parsed properly.
		 */
		hdr->evt = 0xff;

		/* When someone waits for the WMT event, the skb is being cloned
		 * and being processed the events from there then.
		 */
		if (test_bit(BTUSB_TX_WAIT_VND_EVT, &data->flags)) {
			data->evt_skb = skb_clone(skb, GFP_ATOMIC);
			if (!data->evt_skb) {
				kfree_skb(skb);
				return;
			}
		}

		err = hci_recv_frame(hdev, skb);
		if (err < 0) {
			kfree_skb(data->evt_skb);
			data->evt_skb = NULL;
			return;
		}

		if (test_and_clear_bit(BTUSB_TX_WAIT_VND_EVT,
				       &data->flags)) {
			/* Barrier to sync with other CPUs */
			smp_mb__after_atomic();
			wake_up_bit(&data->flags,
				    BTUSB_TX_WAIT_VND_EVT);
		}
		return;
	} else if (urb->status == -ENOENT) {
		/* Avoid suspend failed when usb_kill_urb */
		return;
	}

	usb_mark_last_busy(data->udev);

	/* The URB complete handler is still called with urb->actual_length = 0
	 * when the event is not available, so we should keep re-submitting
	 * URB until WMT event returns, Also, It's necessary to wait some time
	 * between the two consecutive control URBs to relax the target device
	 * to generate the event. Otherwise, the WMT event cannot return from
	 * the device successfully.
	 */
	udelay(500);

	usb_anchor_urb(urb, &data->ctrl_anchor);
	err = usb_submit_urb(urb, GFP_ATOMIC);
	if (err < 0) {
		/* -EPERM: urb is being killed;
		 * -ENODEV: device got disconnected
		 */
		if (err != -EPERM && err != -ENODEV)
			bt_dev_err(hdev, "urb %p failed to resubmit (%d)",
				   urb, -err);
		usb_unanchor_urb(urb);
	}
}

static int btusb_mtk_submit_wmt_recv_urb(struct hci_dev *hdev)
{
	struct btusb_data *data = hci_get_drvdata(hdev);
	struct usb_ctrlrequest *dr;
	unsigned char *buf;
	int err, size = 64;
	unsigned int pipe;
	struct urb *urb;

	urb = usb_alloc_urb(0, GFP_KERNEL);
	if (!urb)
		return -ENOMEM;

	dr = kmalloc(sizeof(*dr), GFP_KERNEL);
	if (!dr) {
		usb_free_urb(urb);
		return -ENOMEM;
	}

	dr->bRequestType = USB_TYPE_VENDOR | USB_DIR_IN;
	dr->bRequest     = 1;
	dr->wIndex       = cpu_to_le16(0);
	dr->wValue       = cpu_to_le16(48);
	dr->wLength      = cpu_to_le16(size);

	buf = kmalloc(size, GFP_KERNEL);
	if (!buf) {
		kfree(dr);
		usb_free_urb(urb);
		return -ENOMEM;
	}

	pipe = usb_rcvctrlpipe(data->udev, 0);

	usb_fill_control_urb(urb, data->udev, pipe, (void *)dr,
			     buf, size, btusb_mtk_wmt_recv, hdev);

	urb->transfer_flags |= URB_FREE_BUFFER;

	usb_anchor_urb(urb, &data->ctrl_anchor);
	err = usb_submit_urb(urb, GFP_KERNEL);
	if (err < 0) {
		if (err != -EPERM && err != -ENODEV)
			bt_dev_err(hdev, "urb %p submission failed (%d)",
				   urb, -err);
		usb_unanchor_urb(urb);
	}

	usb_free_urb(urb);

	return err;
}

static int btusb_mtk_hci_wmt_sync(struct hci_dev *hdev,
				  struct btmtk_hci_wmt_params *wmt_params)
{
	struct btusb_data *data = hci_get_drvdata(hdev);
	struct btmtk_hci_wmt_evt_funcc *wmt_evt_funcc;
	u32 hlen, status = BTMTK_WMT_INVALID;
	struct btmtk_hci_wmt_evt *wmt_evt;
	struct btmtk_hci_wmt_cmd *wc;
	struct btmtk_wmt_hdr *hdr;
	int err;

	/* Submit control IN URB on demand to process the WMT event */
	err = btusb_mtk_submit_wmt_recv_urb(hdev);
	if (err < 0)
		return err;

	/* Send the WMT command and wait until the WMT event returns */
	hlen = sizeof(*hdr) + wmt_params->dlen;
	if (hlen > 255)
		return -EINVAL;

	wc = kzalloc(hlen, GFP_KERNEL);
	if (!wc)
		return -ENOMEM;

	hdr = &wc->hdr;
	hdr->dir = 1;
	hdr->op = wmt_params->op;
	hdr->dlen = cpu_to_le16(wmt_params->dlen + 1);
	hdr->flag = wmt_params->flag;
	memcpy(wc->data, wmt_params->data, wmt_params->dlen);

	set_bit(BTUSB_TX_WAIT_VND_EVT, &data->flags);

	err = __hci_cmd_send(hdev, 0xfc6f, hlen, wc);

	if (err < 0) {
		clear_bit(BTUSB_TX_WAIT_VND_EVT, &data->flags);
		goto err_free_wc;
	}

	/* The vendor specific WMT commands are all answered by a vendor
	 * specific event and will have the Command Status or Command
	 * Complete as with usual HCI command flow control.
	 *
	 * After sending the command, wait for BTUSB_TX_WAIT_VND_EVT
	 * state to be cleared. The driver specific event receive routine
	 * will clear that state and with that indicate completion of the
	 * WMT command.
	 */
	err = wait_on_bit_timeout(&data->flags, BTUSB_TX_WAIT_VND_EVT,
				  TASK_INTERRUPTIBLE, HCI_INIT_TIMEOUT);
	if (err == -EINTR) {
		bt_dev_err(hdev, "Execution of wmt command interrupted");
		clear_bit(BTUSB_TX_WAIT_VND_EVT, &data->flags);
		goto err_free_wc;
	}

	if (err) {
		bt_dev_err(hdev, "Execution of wmt command timed out");
		clear_bit(BTUSB_TX_WAIT_VND_EVT, &data->flags);
		err = -ETIMEDOUT;
		goto err_free_wc;
	}

	/* Parse and handle the return WMT event */
	wmt_evt = (struct btmtk_hci_wmt_evt *)data->evt_skb->data;
	if (wmt_evt->whdr.op != hdr->op) {
		bt_dev_err(hdev, "Wrong op received %d expected %d",
			   wmt_evt->whdr.op, hdr->op);
		err = -EIO;
		goto err_free_skb;
	}

	switch (wmt_evt->whdr.op) {
	case BTMTK_WMT_SEMAPHORE:
		if (wmt_evt->whdr.flag == 2)
			status = BTMTK_WMT_PATCH_UNDONE;
		else
			status = BTMTK_WMT_PATCH_DONE;
		break;
	case BTMTK_WMT_FUNC_CTRL:
		wmt_evt_funcc = (struct btmtk_hci_wmt_evt_funcc *)wmt_evt;
		if (be16_to_cpu(wmt_evt_funcc->status) == 0x404)
			status = BTMTK_WMT_ON_DONE;
		else if (be16_to_cpu(wmt_evt_funcc->status) == 0x420)
			status = BTMTK_WMT_ON_PROGRESS;
		else
			status = BTMTK_WMT_ON_UNDONE;
		break;
	case BTMTK_WMT_PATCH_DWNLD:
		if (wmt_evt->whdr.flag == 2)
			status = BTMTK_WMT_PATCH_DONE;
		else if (wmt_evt->whdr.flag == 1)
			status = BTMTK_WMT_PATCH_PROGRESS;
		else
			status = BTMTK_WMT_PATCH_UNDONE;
		break;
	}

	if (wmt_params->status)
		*wmt_params->status = status;

err_free_skb:
	kfree_skb(data->evt_skb);
	data->evt_skb = NULL;
err_free_wc:
	kfree(wc);
	return err;
}

static int btusb_mtk_setup_firmware_79xx(struct hci_dev *hdev, const char *fwname)
{
	struct btmtk_hci_wmt_params wmt_params;
	struct btmtk_global_desc *globaldesc = NULL;
	struct btmtk_section_map *sectionmap;
	const struct firmware *fw;
	const u8 *fw_ptr;
	const u8 *fw_bin_ptr;
	int err, dlen, i, status;
	u8 flag, first_block, retry;
	u32 section_num, dl_size, section_offset;
	u8 cmd[64];

	err = request_firmware(&fw, fwname, &hdev->dev);
	if (err < 0) {
		bt_dev_err(hdev, "Failed to load firmware file (%d)", err);
		return err;
	}

	fw_ptr = fw->data;
	fw_bin_ptr = fw_ptr;
	globaldesc = (struct btmtk_global_desc *)(fw_ptr + MTK_FW_ROM_PATCH_HEADER_SIZE);
	section_num = le32_to_cpu(globaldesc->section_num);

	for (i = 0; i < section_num; i++) {
		first_block = 1;
		fw_ptr = fw_bin_ptr;
		sectionmap = (struct btmtk_section_map *)(fw_ptr + MTK_FW_ROM_PATCH_HEADER_SIZE +
			      MTK_FW_ROM_PATCH_GD_SIZE + MTK_FW_ROM_PATCH_SEC_MAP_SIZE * i);

		section_offset = le32_to_cpu(sectionmap->secoffset);
		dl_size = le32_to_cpu(sectionmap->bin_info_spec.dlsize);

		if (dl_size > 0) {
			retry = 20;
			while (retry > 0) {
				cmd[0] = 0; /* 0 means legacy dl mode. */
				memcpy(cmd + 1,
				       fw_ptr + MTK_FW_ROM_PATCH_HEADER_SIZE +
				       MTK_FW_ROM_PATCH_GD_SIZE + MTK_FW_ROM_PATCH_SEC_MAP_SIZE * i +
				       MTK_SEC_MAP_COMMON_SIZE,
				       MTK_SEC_MAP_NEED_SEND_SIZE + 1);

				wmt_params.op = BTMTK_WMT_PATCH_DWNLD;
				wmt_params.status = &status;
				wmt_params.flag = 0;
				wmt_params.dlen = MTK_SEC_MAP_NEED_SEND_SIZE + 1;
				wmt_params.data = &cmd;

				err = btusb_mtk_hci_wmt_sync(hdev, &wmt_params);
				if (err < 0) {
					bt_dev_err(hdev, "Failed to send wmt patch dwnld (%d)",
						   err);
					goto err_release_fw;
				}

				if (status == BTMTK_WMT_PATCH_UNDONE) {
					break;
				} else if (status == BTMTK_WMT_PATCH_PROGRESS) {
					msleep(100);
					retry--;
				} else if (status == BTMTK_WMT_PATCH_DONE) {
					goto next_section;
				} else {
					bt_dev_err(hdev, "Failed wmt patch dwnld status (%d)",
						   status);
					goto err_release_fw;
				}
			}

			fw_ptr += section_offset;
			wmt_params.op = BTMTK_WMT_PATCH_DWNLD;
			wmt_params.status = NULL;

			while (dl_size > 0) {
				dlen = min_t(int, 250, dl_size);
				if (first_block == 1) {
					flag = 1;
					first_block = 0;
				} else if (dl_size - dlen <= 0) {
					flag = 3;
				} else {
					flag = 2;
				}

				wmt_params.flag = flag;
				wmt_params.dlen = dlen;
				wmt_params.data = fw_ptr;

				err = btusb_mtk_hci_wmt_sync(hdev, &wmt_params);
				if (err < 0) {
					bt_dev_err(hdev, "Failed to send wmt patch dwnld (%d)",
						   err);
					goto err_release_fw;
				}

				dl_size -= dlen;
				fw_ptr += dlen;
			}
		}
next_section:
		continue;
	}
	/* Wait a few moments for firmware activation done */
	usleep_range(100000, 120000);

err_release_fw:
	release_firmware(fw);

	return err;
}

static int btusb_mtk_setup_firmware(struct hci_dev *hdev, const char *fwname)
{
	struct btmtk_hci_wmt_params wmt_params;
	const struct firmware *fw;
	const u8 *fw_ptr;
	size_t fw_size;
	int err, dlen;
	u8 flag, param;

	err = request_firmware(&fw, fwname, &hdev->dev);
	if (err < 0) {
		bt_dev_err(hdev, "Failed to load firmware file (%d)", err);
		return err;
	}

	/* Power on data RAM the firmware relies on. */
	param = 1;
	wmt_params.op = BTMTK_WMT_FUNC_CTRL;
	wmt_params.flag = 3;
	wmt_params.dlen = sizeof(param);
	wmt_params.data = &param;
	wmt_params.status = NULL;

	err = btusb_mtk_hci_wmt_sync(hdev, &wmt_params);
	if (err < 0) {
		bt_dev_err(hdev, "Failed to power on data RAM (%d)", err);
		goto err_release_fw;
	}

	fw_ptr = fw->data;
	fw_size = fw->size;

	/* The size of patch header is 30 bytes, should be skip */
	if (fw_size < 30) {
		err = -EINVAL;
		goto err_release_fw;
	}

	fw_size -= 30;
	fw_ptr += 30;
	flag = 1;

	wmt_params.op = BTMTK_WMT_PATCH_DWNLD;
	wmt_params.status = NULL;

	while (fw_size > 0) {
		dlen = min_t(int, 250, fw_size);

		/* Tell device the position in sequence */
		if (fw_size - dlen <= 0)
			flag = 3;
		else if (fw_size < fw->size - 30)
			flag = 2;

		wmt_params.flag = flag;
		wmt_params.dlen = dlen;
		wmt_params.data = fw_ptr;

		err = btusb_mtk_hci_wmt_sync(hdev, &wmt_params);
		if (err < 0) {
			bt_dev_err(hdev, "Failed to send wmt patch dwnld (%d)",
				   err);
			goto err_release_fw;
		}

		fw_size -= dlen;
		fw_ptr += dlen;
	}

	wmt_params.op = BTMTK_WMT_RST;
	wmt_params.flag = 4;
	wmt_params.dlen = 0;
	wmt_params.data = NULL;
	wmt_params.status = NULL;

	/* Activate funciton the firmware providing to */
	err = btusb_mtk_hci_wmt_sync(hdev, &wmt_params);
	if (err < 0) {
		bt_dev_err(hdev, "Failed to send wmt rst (%d)", err);
		goto err_release_fw;
	}

	/* Wait a few moments for firmware activation done */
	usleep_range(10000, 12000);

err_release_fw:
	release_firmware(fw);

	return err;
}

static int btusb_mtk_func_query(struct hci_dev *hdev)
{
	struct btmtk_hci_wmt_params wmt_params;
	int status, err;
	u8 param = 0;

	/* Query whether the function is enabled */
	wmt_params.op = BTMTK_WMT_FUNC_CTRL;
	wmt_params.flag = 4;
	wmt_params.dlen = sizeof(param);
	wmt_params.data = &param;
	wmt_params.status = &status;

	err = btusb_mtk_hci_wmt_sync(hdev, &wmt_params);
	if (err < 0) {
		bt_dev_err(hdev, "Failed to query function status (%d)", err);
		return err;
	}

	return status;
}

static int btusb_mtk_reg_read(struct btusb_data *data, u32 reg, u32 *val)
{
	int pipe, err, size = sizeof(u32);
	void *buf;

	buf = kzalloc(size, GFP_KERNEL);
	if (!buf)
		return -ENOMEM;

	pipe = usb_rcvctrlpipe(data->udev, 0);
	err = usb_control_msg(data->udev, pipe, 0x63,
			      USB_TYPE_VENDOR | USB_DIR_IN,
			      reg >> 16, reg & 0xffff,
			      buf, size, USB_CTRL_SET_TIMEOUT);
	if (err < 0)
		goto err_free_buf;

	*val = get_unaligned_le32(buf);

err_free_buf:
	kfree(buf);

	return err;
}

static int btusb_mtk_id_get(struct btusb_data *data, u32 reg, u32 *id)
{
	return btusb_mtk_reg_read(data, reg, id);
}

static int btusb_mtk_setup(struct hci_dev *hdev)
{
	struct btusb_data *data = hci_get_drvdata(hdev);
	struct btmtk_hci_wmt_params wmt_params;
	ktime_t calltime, delta, rettime;
	struct btmtk_tci_sleep tci_sleep;
	unsigned long long duration;
	struct sk_buff *skb;
	const char *fwname;
	int err, status;
	u32 dev_id;
	char fw_bin_name[64];
	u32 fw_version = 0;
	u8 param;

	calltime = ktime_get();

	err = btusb_mtk_id_get(data, 0x80000008, &dev_id);
	if (err < 0) {
		bt_dev_err(hdev, "Failed to get device id (%d)", err);
		return err;
	}

	if (!dev_id) {
		err = btusb_mtk_id_get(data, 0x70010200, &dev_id);
		if (err < 0) {
			bt_dev_err(hdev, "Failed to get device id (%d)", err);
			return err;
		}
		err = btusb_mtk_id_get(data, 0x80021004, &fw_version);
		if (err < 0) {
			bt_dev_err(hdev, "Failed to get fw version (%d)", err);
			return err;
		}
	}

	switch (dev_id) {
	case 0x7663:
		fwname = FIRMWARE_MT7663;
		break;
	case 0x7668:
		fwname = FIRMWARE_MT7668;
		break;
	case 0x7961:
		snprintf(fw_bin_name, sizeof(fw_bin_name),
			"mediatek/BT_RAM_CODE_MT%04x_1_%x_hdr.bin",
			 dev_id & 0xffff, (fw_version & 0xff) + 1);
		err = btusb_mtk_setup_firmware_79xx(hdev, fw_bin_name);

		/* Enable Bluetooth protocol */
		param = 1;
		wmt_params.op = BTMTK_WMT_FUNC_CTRL;
		wmt_params.flag = 0;
		wmt_params.dlen = sizeof(param);
		wmt_params.data = &param;
		wmt_params.status = NULL;

		err = btusb_mtk_hci_wmt_sync(hdev, &wmt_params);
		if (err < 0) {
			bt_dev_err(hdev, "Failed to send wmt func ctrl (%d)", err);
			return err;
		}
		goto done;
	default:
		bt_dev_err(hdev, "Unsupported hardware variant (%08x)",
			   dev_id);
		return -ENODEV;
	}

	/* Query whether the firmware is already download */
	wmt_params.op = BTMTK_WMT_SEMAPHORE;
	wmt_params.flag = 1;
	wmt_params.dlen = 0;
	wmt_params.data = NULL;
	wmt_params.status = &status;

	err = btusb_mtk_hci_wmt_sync(hdev, &wmt_params);
	if (err < 0) {
		bt_dev_err(hdev, "Failed to query firmware status (%d)", err);
		return err;
	}

	if (status == BTMTK_WMT_PATCH_DONE) {
		bt_dev_info(hdev, "firmware already downloaded");
		goto ignore_setup_fw;
	}

	/* Setup a firmware which the device definitely requires */
	err = btusb_mtk_setup_firmware(hdev, fwname);
	if (err < 0)
		return err;

ignore_setup_fw:
	err = readx_poll_timeout(btusb_mtk_func_query, hdev, status,
				 status < 0 || status != BTMTK_WMT_ON_PROGRESS,
				 2000, 5000000);
	/* -ETIMEDOUT happens */
	if (err < 0)
		return err;

	/* The other errors happen in btusb_mtk_func_query */
	if (status < 0)
		return status;

	if (status == BTMTK_WMT_ON_DONE) {
		bt_dev_info(hdev, "function already on");
		goto ignore_func_on;
	}

	/* Enable Bluetooth protocol */
	param = 1;
	wmt_params.op = BTMTK_WMT_FUNC_CTRL;
	wmt_params.flag = 0;
	wmt_params.dlen = sizeof(param);
	wmt_params.data = &param;
	wmt_params.status = NULL;

	err = btusb_mtk_hci_wmt_sync(hdev, &wmt_params);
	if (err < 0) {
		bt_dev_err(hdev, "Failed to send wmt func ctrl (%d)", err);
		return err;
	}

ignore_func_on:
	/* Apply the low power environment setup */
	tci_sleep.mode = 0x5;
	tci_sleep.duration = cpu_to_le16(0x640);
	tci_sleep.host_duration = cpu_to_le16(0x640);
	tci_sleep.host_wakeup_pin = 0;
	tci_sleep.time_compensation = 0;

	skb = __hci_cmd_sync(hdev, 0xfc7a, sizeof(tci_sleep), &tci_sleep,
			     HCI_INIT_TIMEOUT);
	if (IS_ERR(skb)) {
		err = PTR_ERR(skb);
		bt_dev_err(hdev, "Failed to apply low power setting (%d)", err);
		return err;
	}
	kfree_skb(skb);

done:
	rettime = ktime_get();
	delta = ktime_sub(rettime, calltime);
	duration = (unsigned long long)ktime_to_ns(delta) >> 10;

	bt_dev_info(hdev, "Device setup in %llu usecs", duration);

	return 0;
}

static int btusb_mtk_shutdown(struct hci_dev *hdev)
{
	struct btmtk_hci_wmt_params wmt_params;
	u8 param = 0;
	int err;

	/* Disable the device */
	wmt_params.op = BTMTK_WMT_FUNC_CTRL;
	wmt_params.flag = 0;
	wmt_params.dlen = sizeof(param);
	wmt_params.data = &param;
	wmt_params.status = NULL;

	err = btusb_mtk_hci_wmt_sync(hdev, &wmt_params);
	if (err < 0) {
		bt_dev_err(hdev, "Failed to send wmt func ctrl (%d)", err);
		return err;
	}

	return 0;
}

MODULE_FIRMWARE(FIRMWARE_MT7663);
MODULE_FIRMWARE(FIRMWARE_MT7668);

#ifdef CONFIG_PM
/* Configure an out-of-band gpio as wake-up pin, if specified in device tree */
static int marvell_config_oob_wake(struct hci_dev *hdev)
{
	struct sk_buff *skb;
	struct btusb_data *data = hci_get_drvdata(hdev);
	struct device *dev = &data->udev->dev;
	u16 pin, gap, opcode;
	int ret;
	u8 cmd[5];

	/* Move on if no wakeup pin specified */
	if (of_property_read_u16(dev->of_node, "marvell,wakeup-pin", &pin) ||
	    of_property_read_u16(dev->of_node, "marvell,wakeup-gap-ms", &gap))
		return 0;

	/* Vendor specific command to configure a GPIO as wake-up pin */
	opcode = hci_opcode_pack(0x3F, 0x59);
	cmd[0] = opcode & 0xFF;
	cmd[1] = opcode >> 8;
	cmd[2] = 2; /* length of parameters that follow */
	cmd[3] = pin;
	cmd[4] = gap; /* time in ms, for which wakeup pin should be asserted */

	skb = bt_skb_alloc(sizeof(cmd), GFP_KERNEL);
	if (!skb) {
		bt_dev_err(hdev, "%s: No memory", __func__);
		return -ENOMEM;
	}

	skb_put_data(skb, cmd, sizeof(cmd));
	hci_skb_pkt_type(skb) = HCI_COMMAND_PKT;

	ret = btusb_send_frame(hdev, skb);
	if (ret) {
		bt_dev_err(hdev, "%s: configuration failed", __func__);
		kfree_skb(skb);
		return ret;
	}

	return 0;
}
#endif

static int btusb_set_bdaddr_marvell(struct hci_dev *hdev,
				    const bdaddr_t *bdaddr)
{
	struct sk_buff *skb;
	u8 buf[8];
	long ret;

	buf[0] = 0xfe;
	buf[1] = sizeof(bdaddr_t);
	memcpy(buf + 2, bdaddr, sizeof(bdaddr_t));

	skb = __hci_cmd_sync(hdev, 0xfc22, sizeof(buf), buf, HCI_INIT_TIMEOUT);
	if (IS_ERR(skb)) {
		ret = PTR_ERR(skb);
		bt_dev_err(hdev, "changing Marvell device address failed (%ld)",
			   ret);
		return ret;
	}
	kfree_skb(skb);

	return 0;
}

static int btusb_set_bdaddr_ath3012(struct hci_dev *hdev,
				    const bdaddr_t *bdaddr)
{
	struct sk_buff *skb;
	u8 buf[10];
	long ret;

	buf[0] = 0x01;
	buf[1] = 0x01;
	buf[2] = 0x00;
	buf[3] = sizeof(bdaddr_t);
	memcpy(buf + 4, bdaddr, sizeof(bdaddr_t));

	skb = __hci_cmd_sync(hdev, 0xfc0b, sizeof(buf), buf, HCI_INIT_TIMEOUT);
	if (IS_ERR(skb)) {
		ret = PTR_ERR(skb);
		bt_dev_err(hdev, "Change address command failed (%ld)", ret);
		return ret;
	}
	kfree_skb(skb);

	return 0;
}

static int btusb_set_bdaddr_wcn6855(struct hci_dev *hdev,
				const bdaddr_t *bdaddr)
{
	struct sk_buff *skb;
	u8 buf[6];
	long ret;

	memcpy(buf, bdaddr, sizeof(bdaddr_t));

	skb = __hci_cmd_sync_ev(hdev, 0xfc14, sizeof(buf), buf,
				HCI_EV_CMD_COMPLETE, HCI_INIT_TIMEOUT);
	if (IS_ERR(skb)) {
		ret = PTR_ERR(skb);
		bt_dev_err(hdev, "Change address command failed (%ld)", ret);
		return ret;
	}
	kfree_skb(skb);

	return 0;
}

#define QCA_DFU_PACKET_LEN	4096

#define QCA_GET_TARGET_VERSION	0x09
#define QCA_CHECK_STATUS	0x05
#define QCA_DFU_DOWNLOAD	0x01

#define QCA_SYSCFG_UPDATED	0x40
#define QCA_PATCH_UPDATED	0x80
#define QCA_DFU_TIMEOUT		3000
#define QCA_FLAG_MULTI_NVM      0x80

struct qca_version {
	__le32	rom_version;
	__le32	patch_version;
	__le32	ram_version;
	__le16	board_id;
	__le16	flag;
	__u8	reserved[4];
} __packed;

struct qca_rampatch_version {
	__le16	rom_version_high;
	__le16  rom_version_low;
	__le16	patch_version;
} __packed;

struct qca_device_info {
	u32	rom_version;
	u8	rampatch_hdr;	/* length of header in rampatch */
	u8	nvm_hdr;	/* length of header in NVM */
	u8	ver_offset;	/* offset of version structure in rampatch */
};

static const struct qca_device_info qca_devices_table[] = {
	{ 0x00000100, 20, 4,  8 }, /* Rome 1.0 */
	{ 0x00000101, 20, 4,  8 }, /* Rome 1.1 */
	{ 0x00000200, 28, 4, 16 }, /* Rome 2.0 */
	{ 0x00000201, 28, 4, 16 }, /* Rome 2.1 */
	{ 0x00000300, 28, 4, 16 }, /* Rome 3.0 */
	{ 0x00000302, 28, 4, 16 }, /* Rome 3.2 */
	{ 0x00130100, 40, 4, 16 }, /* WCN6855 1.0 */
	{ 0x00130200, 40, 4, 16 }, /* WCN6855 2.0 */
};

static int btusb_qca_send_vendor_req(struct usb_device *udev, u8 request,
				     void *data, u16 size)
{
	int pipe, err;
	u8 *buf;

	buf = kmalloc(size, GFP_KERNEL);
	if (!buf)
		return -ENOMEM;

	/* Found some of USB hosts have IOT issues with ours so that we should
	 * not wait until HCI layer is ready.
	 */
	pipe = usb_rcvctrlpipe(udev, 0);
	err = usb_control_msg(udev, pipe, request, USB_TYPE_VENDOR | USB_DIR_IN,
			      0, 0, buf, size, USB_CTRL_SET_TIMEOUT);
	if (err < 0) {
		dev_err(&udev->dev, "Failed to access otp area (%d)", err);
		goto done;
	}

	memcpy(data, buf, size);

done:
	kfree(buf);

	return err;
}

static int btusb_setup_qca_download_fw(struct hci_dev *hdev,
				       const struct firmware *firmware,
				       size_t hdr_size)
{
	struct btusb_data *btdata = hci_get_drvdata(hdev);
	struct usb_device *udev = btdata->udev;
	size_t count, size, sent = 0;
	int pipe, len, err;
	u8 *buf;

	buf = kmalloc(QCA_DFU_PACKET_LEN, GFP_KERNEL);
	if (!buf)
		return -ENOMEM;

	count = firmware->size;

	size = min_t(size_t, count, hdr_size);
	memcpy(buf, firmware->data, size);

	/* USB patches should go down to controller through USB path
	 * because binary format fits to go down through USB channel.
	 * USB control path is for patching headers and USB bulk is for
	 * patch body.
	 */
	pipe = usb_sndctrlpipe(udev, 0);
	err = usb_control_msg(udev, pipe, QCA_DFU_DOWNLOAD, USB_TYPE_VENDOR,
			      0, 0, buf, size, USB_CTRL_SET_TIMEOUT);
	if (err < 0) {
		bt_dev_err(hdev, "Failed to send headers (%d)", err);
		goto done;
	}

	sent += size;
	count -= size;

	while (count) {
		size = min_t(size_t, count, QCA_DFU_PACKET_LEN);

		memcpy(buf, firmware->data + sent, size);

		pipe = usb_sndbulkpipe(udev, 0x02);
		err = usb_bulk_msg(udev, pipe, buf, size, &len,
				   QCA_DFU_TIMEOUT);
		if (err < 0) {
			bt_dev_err(hdev, "Failed to send body at %zd of %zd (%d)",
				   sent, firmware->size, err);
			break;
		}

		if (size != len) {
			bt_dev_err(hdev, "Failed to get bulk buffer");
			err = -EILSEQ;
			break;
		}

		sent  += size;
		count -= size;
	}

done:
	kfree(buf);
	return err;
}

static int btusb_setup_qca_load_rampatch(struct hci_dev *hdev,
					 struct qca_version *ver,
					 const struct qca_device_info *info)
{
	struct qca_rampatch_version *rver;
	const struct firmware *fw;
	u32 ver_rom, ver_patch, rver_rom;
	u16 rver_rom_low, rver_rom_high, rver_patch;
	char fwname[64];
	int err;

	ver_rom = le32_to_cpu(ver->rom_version);
	ver_patch = le32_to_cpu(ver->patch_version);

	snprintf(fwname, sizeof(fwname), "qca/rampatch_usb_%08x.bin", ver_rom);

	err = request_firmware(&fw, fwname, &hdev->dev);
	if (err) {
		bt_dev_err(hdev, "failed to request rampatch file: %s (%d)",
			   fwname, err);
		return err;
	}

	bt_dev_info(hdev, "using rampatch file: %s", fwname);

	rver = (struct qca_rampatch_version *)(fw->data + info->ver_offset);
	rver_rom_low = le16_to_cpu(rver->rom_version_low);
	rver_patch = le16_to_cpu(rver->patch_version);

	if (ver_rom & ~0xffffU) {
		rver_rom_high = le16_to_cpu(rver->rom_version_high);
		rver_rom = le32_to_cpu(rver_rom_high << 16 | rver_rom_low);
	} else {
		rver_rom = rver_rom_low;
	}

	bt_dev_info(hdev, "QCA: patch rome 0x%x build 0x%x, "
		    "firmware rome 0x%x build 0x%x",
		    rver_rom, rver_patch, ver_rom, ver_patch);

	if (rver_rom != ver_rom || rver_patch <= ver_patch) {
		bt_dev_err(hdev, "rampatch file version did not match with firmware");
		err = -EINVAL;
		goto done;
	}

	err = btusb_setup_qca_download_fw(hdev, fw, info->rampatch_hdr);

done:
	release_firmware(fw);

	return err;
}

static int btusb_setup_qca_load_nvm(struct hci_dev *hdev,
				    struct qca_version *ver,
				    const struct qca_device_info *info)
{
	const struct firmware *fw;
	char fwname[64];
	int err;

	if (((ver->flag >> 8) & 0xff) == QCA_FLAG_MULTI_NVM) {
		snprintf(fwname, sizeof(fwname), "qca/nvm_usb_%08x_%04x.bin",
			 le32_to_cpu(ver->rom_version),
			 le16_to_cpu(ver->board_id));
	} else {
		snprintf(fwname, sizeof(fwname), "qca/nvm_usb_%08x.bin",
			 le32_to_cpu(ver->rom_version));
	}

	err = request_firmware(&fw, fwname, &hdev->dev);
	if (err) {
		bt_dev_err(hdev, "failed to request NVM file: %s (%d)",
			   fwname, err);
		return err;
	}

	bt_dev_info(hdev, "using NVM file: %s", fwname);

	err = btusb_setup_qca_download_fw(hdev, fw, info->nvm_hdr);

	release_firmware(fw);

	return err;
}

/* identify the ROM version and check whether patches are needed */
static bool btusb_qca_need_patch(struct usb_device *udev)
{
	struct qca_version ver;

	if (btusb_qca_send_vendor_req(udev, QCA_GET_TARGET_VERSION, &ver,
				      sizeof(ver)) < 0)
		return false;
	/* only low ROM versions need patches */
	return !(le32_to_cpu(ver.rom_version) & ~0xffffU);
}

static int btusb_setup_qca(struct hci_dev *hdev)
{
	struct btusb_data *btdata = hci_get_drvdata(hdev);
	struct usb_device *udev = btdata->udev;
	const struct qca_device_info *info = NULL;
	struct qca_version ver;
	u32 ver_rom;
	u8 status;
	int i, err;

	err = btusb_qca_send_vendor_req(udev, QCA_GET_TARGET_VERSION, &ver,
					sizeof(ver));
	if (err < 0)
		return err;

	ver_rom = le32_to_cpu(ver.rom_version);

	for (i = 0; i < ARRAY_SIZE(qca_devices_table); i++) {
		if (ver_rom == qca_devices_table[i].rom_version)
			info = &qca_devices_table[i];
	}
	if (!info) {
		/* If the rom_version is not matched in the qca_devices_table
		 * and the high ROM version is not zero, we assume this chip no
		 * need to load the rampatch and nvm.
		 */
		if (ver_rom & ~0xffffU)
			return 0;

		bt_dev_err(hdev, "don't support firmware rome 0x%x", ver_rom);
		return -ENODEV;
	}

	err = btusb_qca_send_vendor_req(udev, QCA_CHECK_STATUS, &status,
					sizeof(status));
	if (err < 0)
		return err;

	if (!(status & QCA_PATCH_UPDATED)) {
		err = btusb_setup_qca_load_rampatch(hdev, &ver, info);
		if (err < 0)
			return err;
	}

	err = btusb_qca_send_vendor_req(udev, QCA_GET_TARGET_VERSION, &ver,
					sizeof(ver));
	if (err < 0)
		return err;

	if (!(status & QCA_SYSCFG_UPDATED)) {
		err = btusb_setup_qca_load_nvm(hdev, &ver, info);
		if (err < 0)
			return err;
	}

	return 0;
}

static inline int __set_diag_interface(struct hci_dev *hdev)
{
	struct btusb_data *data = hci_get_drvdata(hdev);
	struct usb_interface *intf = data->diag;
	int i;

	if (!data->diag)
		return -ENODEV;

	data->diag_tx_ep = NULL;
	data->diag_rx_ep = NULL;

	for (i = 0; i < intf->cur_altsetting->desc.bNumEndpoints; i++) {
		struct usb_endpoint_descriptor *ep_desc;

		ep_desc = &intf->cur_altsetting->endpoint[i].desc;

		if (!data->diag_tx_ep && usb_endpoint_is_bulk_out(ep_desc)) {
			data->diag_tx_ep = ep_desc;
			continue;
		}

		if (!data->diag_rx_ep && usb_endpoint_is_bulk_in(ep_desc)) {
			data->diag_rx_ep = ep_desc;
			continue;
		}
	}

	if (!data->diag_tx_ep || !data->diag_rx_ep) {
		bt_dev_err(hdev, "invalid diagnostic descriptors");
		return -ENODEV;
	}

	return 0;
}

static struct urb *alloc_diag_urb(struct hci_dev *hdev, bool enable)
{
	struct btusb_data *data = hci_get_drvdata(hdev);
	struct sk_buff *skb;
	struct urb *urb;
	unsigned int pipe;

	if (!data->diag_tx_ep)
		return ERR_PTR(-ENODEV);

	urb = usb_alloc_urb(0, GFP_KERNEL);
	if (!urb)
		return ERR_PTR(-ENOMEM);

	skb = bt_skb_alloc(2, GFP_KERNEL);
	if (!skb) {
		usb_free_urb(urb);
		return ERR_PTR(-ENOMEM);
	}

	skb_put_u8(skb, 0xf0);
	skb_put_u8(skb, enable);

	pipe = usb_sndbulkpipe(data->udev, data->diag_tx_ep->bEndpointAddress);

	usb_fill_bulk_urb(urb, data->udev, pipe,
			  skb->data, skb->len, btusb_tx_complete, skb);

	skb->dev = (void *)hdev;

	return urb;
}

static int btusb_bcm_set_diag(struct hci_dev *hdev, bool enable)
{
	struct btusb_data *data = hci_get_drvdata(hdev);
	struct urb *urb;

	if (!data->diag)
		return -ENODEV;

	if (!test_bit(HCI_RUNNING, &hdev->flags))
		return -ENETDOWN;

	urb = alloc_diag_urb(hdev, enable);
	if (IS_ERR(urb))
		return PTR_ERR(urb);

	return submit_or_queue_tx_urb(hdev, urb);
}

#ifdef CONFIG_PM
static irqreturn_t btusb_oob_wake_handler(int irq, void *priv)
{
	struct btusb_data *data = priv;

	pm_wakeup_event(&data->udev->dev, 0);
	pm_system_wakeup();

	/* Disable only if not already disabled (keep it balanced) */
	if (test_and_clear_bit(BTUSB_OOB_WAKE_ENABLED, &data->flags)) {
		disable_irq_nosync(irq);
		disable_irq_wake(irq);
	}
	return IRQ_HANDLED;
}

static const struct of_device_id btusb_match_table[] = {
	{ .compatible = "usb1286,204e" },
	{ .compatible = "usbcf3,e300" }, /* QCA6174A */
	{ .compatible = "usb4ca,301a" }, /* QCA6174A (Lite-On) */
	{ }
};
MODULE_DEVICE_TABLE(of, btusb_match_table);

/* Use an oob wakeup pin? */
static int btusb_config_oob_wake(struct hci_dev *hdev)
{
	struct btusb_data *data = hci_get_drvdata(hdev);
	struct device *dev = &data->udev->dev;
	int irq, ret;

	clear_bit(BTUSB_OOB_WAKE_ENABLED, &data->flags);

	if (!of_match_device(btusb_match_table, dev))
		return 0;

	/* Move on if no IRQ specified */
	irq = of_irq_get_byname(dev->of_node, "wakeup");
	if (irq <= 0) {
		bt_dev_dbg(hdev, "%s: no OOB Wakeup IRQ in DT", __func__);
		return 0;
	}

	irq_set_status_flags(irq, IRQ_NOAUTOEN);
	ret = devm_request_irq(&hdev->dev, irq, btusb_oob_wake_handler,
			       0, "OOB Wake-on-BT", data);
	if (ret) {
		bt_dev_err(hdev, "%s: IRQ request failed", __func__);
		return ret;
	}

	ret = device_init_wakeup(dev, true);
	if (ret) {
		bt_dev_err(hdev, "%s: failed to init_wakeup", __func__);
		return ret;
	}

	data->oob_wake_irq = irq;
	bt_dev_info(hdev, "OOB Wake-on-BT configured at IRQ %u", irq);
	return 0;
}
#endif

static void btusb_check_needs_reset_resume(struct usb_interface *intf)
{
	if (dmi_check_system(btusb_needs_reset_resume_table))
		interface_to_usbdev(intf)->quirks |= USB_QUIRK_RESET_RESUME;
}

static bool btusb_prevent_wake(struct hci_dev *hdev)
{
	struct btusb_data *data = hci_get_drvdata(hdev);

	if (test_bit(BTUSB_WAKEUP_DISABLE, &data->flags))
		return true;

	return !device_may_wakeup(&data->udev->dev);
}

static int btusb_shutdown_qca(struct hci_dev *hdev)
{
	struct sk_buff *skb;

	skb = __hci_cmd_sync(hdev, HCI_OP_RESET, 0, NULL, HCI_INIT_TIMEOUT);
	if (IS_ERR(skb)) {
		bt_dev_err(hdev, "HCI reset during shutdown failed");
		return PTR_ERR(skb);
	}
	kfree_skb(skb);

	return 0;
}

static int btusb_probe(struct usb_interface *intf,
		       const struct usb_device_id *id)
{
	struct usb_endpoint_descriptor *ep_desc;
	struct gpio_desc *reset_gpio;
	struct btusb_data *data;
	struct hci_dev *hdev;
	unsigned ifnum_base;
	int i, err;

	BT_DBG("intf %p id %p", intf, id);

	/* interface numbers are hardcoded in the spec */
	if (intf->cur_altsetting->desc.bInterfaceNumber != 0) {
		if (!(id->driver_info & BTUSB_IFNUM_2))
			return -ENODEV;
		if (intf->cur_altsetting->desc.bInterfaceNumber != 2)
			return -ENODEV;
	}

	ifnum_base = intf->cur_altsetting->desc.bInterfaceNumber;

	if (!id->driver_info) {
		const struct usb_device_id *match;

		match = usb_match_id(intf, blacklist_table);
		if (match)
			id = match;
	}

	if (id->driver_info == BTUSB_IGNORE)
		return -ENODEV;

	if (id->driver_info & BTUSB_ATH3012) {
		struct usb_device *udev = interface_to_usbdev(intf);

		/* Old firmware would otherwise let ath3k driver load
		 * patch and sysconfig files
		 */
		if (le16_to_cpu(udev->descriptor.bcdDevice) <= 0x0001 &&
		    !btusb_qca_need_patch(udev))
			return -ENODEV;
	}

	data = devm_kzalloc(&intf->dev, sizeof(*data), GFP_KERNEL);
	if (!data)
		return -ENOMEM;

	for (i = 0; i < intf->cur_altsetting->desc.bNumEndpoints; i++) {
		ep_desc = &intf->cur_altsetting->endpoint[i].desc;

		if (!data->intr_ep && usb_endpoint_is_int_in(ep_desc)) {
			data->intr_ep = ep_desc;
			continue;
		}

		if (!data->bulk_tx_ep && usb_endpoint_is_bulk_out(ep_desc)) {
			data->bulk_tx_ep = ep_desc;
			continue;
		}

		if (!data->bulk_rx_ep && usb_endpoint_is_bulk_in(ep_desc)) {
			data->bulk_rx_ep = ep_desc;
			continue;
		}
	}

	if (!data->intr_ep || !data->bulk_tx_ep || !data->bulk_rx_ep)
		return -ENODEV;

	if (id->driver_info & BTUSB_AMP) {
		data->cmdreq_type = USB_TYPE_CLASS | 0x01;
		data->cmdreq = 0x2b;
	} else {
		data->cmdreq_type = USB_TYPE_CLASS;
		data->cmdreq = 0x00;
	}

	data->udev = interface_to_usbdev(intf);
	data->intf = intf;

	INIT_WORK(&data->work, btusb_work);
	INIT_WORK(&data->waker, btusb_waker);
	init_usb_anchor(&data->deferred);
	init_usb_anchor(&data->tx_anchor);
	spin_lock_init(&data->txlock);

	init_usb_anchor(&data->intr_anchor);
	init_usb_anchor(&data->bulk_anchor);
	init_usb_anchor(&data->isoc_anchor);
	init_usb_anchor(&data->diag_anchor);
	init_usb_anchor(&data->ctrl_anchor);
	spin_lock_init(&data->rxlock);

	if (id->driver_info & BTUSB_INTEL_NEW) {
		data->recv_event = btusb_recv_event_intel;
		data->recv_bulk = btusb_recv_bulk_intel;
		set_bit(BTUSB_BOOTLOADER, &data->flags);
	} else {
		data->recv_event = hci_recv_frame;
		data->recv_bulk = btusb_recv_bulk;
	}

	hdev = hci_alloc_dev();
	if (!hdev)
		return -ENOMEM;

	hdev->bus = HCI_USB;
	hci_set_drvdata(hdev, data);

	if (id->driver_info & BTUSB_AMP)
		hdev->dev_type = HCI_AMP;
	else
		hdev->dev_type = HCI_PRIMARY;

	data->hdev = hdev;

	SET_HCIDEV_DEV(hdev, &intf->dev);

	reset_gpio = gpiod_get_optional(&data->udev->dev, "reset",
					GPIOD_OUT_LOW);
	if (IS_ERR(reset_gpio)) {
		err = PTR_ERR(reset_gpio);
		goto out_free_dev;
	} else if (reset_gpio) {
		data->reset_gpio = reset_gpio;
	}

	hdev->open   = btusb_open;
	hdev->close  = btusb_close;
	hdev->flush  = btusb_flush;
	hdev->send   = btusb_send_frame;
	hdev->notify = btusb_notify;
	hdev->prevent_wake = btusb_prevent_wake;

#ifdef CONFIG_PM
	err = btusb_config_oob_wake(hdev);
	if (err)
		goto out_free_dev;

	/* Marvell devices may need a specific chip configuration */
	if (id->driver_info & BTUSB_MARVELL && data->oob_wake_irq) {
		err = marvell_config_oob_wake(hdev);
		if (err)
			goto out_free_dev;
	}
#endif
	if (id->driver_info & BTUSB_CW6622)
		set_bit(HCI_QUIRK_BROKEN_STORED_LINK_KEY, &hdev->quirks);

	if (id->driver_info & BTUSB_BCM2045)
		set_bit(HCI_QUIRK_BROKEN_STORED_LINK_KEY, &hdev->quirks);

	if (id->driver_info & BTUSB_BCM92035)
		hdev->setup = btusb_setup_bcm92035;

	if (IS_ENABLED(CONFIG_BT_HCIBTUSB_BCM) &&
	    (id->driver_info & BTUSB_BCM_PATCHRAM)) {
		hdev->manufacturer = 15;
		hdev->setup = btbcm_setup_patchram;
		hdev->set_diag = btusb_bcm_set_diag;
		hdev->set_bdaddr = btbcm_set_bdaddr;

		/* Broadcom LM_DIAG Interface numbers are hardcoded */
		data->diag = usb_ifnum_to_if(data->udev, ifnum_base + 2);
	}

	if (IS_ENABLED(CONFIG_BT_HCIBTUSB_BCM) &&
	    (id->driver_info & BTUSB_BCM_APPLE)) {
		hdev->manufacturer = 15;
		hdev->setup = btbcm_setup_apple;
		hdev->set_diag = btusb_bcm_set_diag;

		/* Broadcom LM_DIAG Interface numbers are hardcoded */
		data->diag = usb_ifnum_to_if(data->udev, ifnum_base + 2);
	}

	if (id->driver_info & BTUSB_INTEL) {
		hdev->manufacturer = 2;
		hdev->setup = btusb_setup_intel;
		hdev->shutdown = btusb_shutdown_intel;
		hdev->set_diag = btintel_set_diag_mfg;
		hdev->set_bdaddr = btintel_set_bdaddr;
		hdev->cmd_timeout = btusb_intel_cmd_timeout;
		set_bit(HCI_QUIRK_STRICT_DUPLICATE_FILTER, &hdev->quirks);
		set_bit(HCI_QUIRK_SIMULTANEOUS_DISCOVERY, &hdev->quirks);
		set_bit(HCI_QUIRK_NON_PERSISTENT_DIAG, &hdev->quirks);
	}

	if (id->driver_info & BTUSB_INTEL_NEW) {
		hdev->manufacturer = 2;
		hdev->send = btusb_send_frame_intel;
		hdev->setup = btusb_setup_intel_new;
		hdev->shutdown = btusb_shutdown_intel_new;
		hdev->hw_error = btintel_hw_error;
		hdev->set_diag = btintel_set_diag;
		hdev->set_bdaddr = btintel_set_bdaddr;
		hdev->cmd_timeout = btusb_intel_cmd_timeout;
		set_bit(HCI_QUIRK_STRICT_DUPLICATE_FILTER, &hdev->quirks);
		set_bit(HCI_QUIRK_SIMULTANEOUS_DISCOVERY, &hdev->quirks);
		set_bit(HCI_QUIRK_NON_PERSISTENT_DIAG, &hdev->quirks);
	}

	if (id->driver_info & BTUSB_INTEL_NEWGEN) {
		hdev->manufacturer = 2;
		hdev->send = btusb_send_frame_intel;
		hdev->setup = btusb_setup_intel_newgen;
		hdev->shutdown = btusb_shutdown_intel_new;
		hdev->hw_error = btintel_hw_error;
		hdev->set_diag = btintel_set_diag;
		hdev->set_bdaddr = btintel_set_bdaddr;
		hdev->cmd_timeout = btusb_intel_cmd_timeout;
		set_bit(HCI_QUIRK_STRICT_DUPLICATE_FILTER, &hdev->quirks);
		set_bit(HCI_QUIRK_SIMULTANEOUS_DISCOVERY, &hdev->quirks);
		set_bit(HCI_QUIRK_NON_PERSISTENT_DIAG, &hdev->quirks);

		data->recv_event = btusb_recv_event_intel;
		data->recv_bulk = btusb_recv_bulk_intel;
		set_bit(BTUSB_BOOTLOADER, &data->flags);
	}

	if (id->driver_info & BTUSB_MARVELL)
		hdev->set_bdaddr = btusb_set_bdaddr_marvell;

	if (IS_ENABLED(CONFIG_BT_HCIBTUSB_MTK) &&
	    (id->driver_info & BTUSB_MEDIATEK)) {
		hdev->setup = btusb_mtk_setup;
		hdev->shutdown = btusb_mtk_shutdown;
		hdev->manufacturer = 70;
		set_bit(HCI_QUIRK_NON_PERSISTENT_SETUP, &hdev->quirks);
	}

	if (id->driver_info & BTUSB_SWAVE) {
		set_bit(HCI_QUIRK_FIXUP_INQUIRY_MODE, &hdev->quirks);
		set_bit(HCI_QUIRK_BROKEN_LOCAL_COMMANDS, &hdev->quirks);
	}

	if (id->driver_info & BTUSB_INTEL_BOOT) {
		hdev->manufacturer = 2;
		set_bit(HCI_QUIRK_RAW_DEVICE, &hdev->quirks);
	}

	if (id->driver_info & BTUSB_ATH3012) {
		data->setup_on_usb = btusb_setup_qca;
		hdev->set_bdaddr = btusb_set_bdaddr_ath3012;
		set_bit(HCI_QUIRK_SIMULTANEOUS_DISCOVERY, &hdev->quirks);
		set_bit(HCI_QUIRK_STRICT_DUPLICATE_FILTER, &hdev->quirks);
	}

	if (id->driver_info & BTUSB_QCA_ROME) {
		data->setup_on_usb = btusb_setup_qca;
		hdev->set_bdaddr = btusb_set_bdaddr_ath3012;
		hdev->cmd_timeout = btusb_qca_cmd_timeout;
		set_bit(HCI_QUIRK_SIMULTANEOUS_DISCOVERY, &hdev->quirks);
		btusb_check_needs_reset_resume(intf);
	}

	if (id->driver_info & BTUSB_QCA_WCN6855) {
		data->setup_on_usb = btusb_setup_qca;
		hdev->shutdown = btusb_shutdown_qca;
		hdev->set_bdaddr = btusb_set_bdaddr_wcn6855;
		hdev->cmd_timeout = btusb_qca_cmd_timeout;
		set_bit(HCI_QUIRK_SIMULTANEOUS_DISCOVERY, &hdev->quirks);
	}

	if (id->driver_info & BTUSB_AMP) {
		/* AMP controllers do not support SCO packets */
		data->isoc = NULL;
	} else {
		/* Interface orders are hardcoded in the specification */
		data->isoc = usb_ifnum_to_if(data->udev, ifnum_base + 1);
		data->isoc_ifnum = ifnum_base + 1;
	}

	if (IS_ENABLED(CONFIG_BT_HCIBTUSB_RTL) &&
	    (id->driver_info & BTUSB_REALTEK)) {
		hdev->setup = btrtl_setup_realtek;
		hdev->shutdown = btrtl_shutdown_realtek;
		hdev->cmd_timeout = btusb_rtl_cmd_timeout;

		/* Realtek devices lose their updated firmware over global
		 * suspend that means host doesn't send SET_FEATURE
		 * (DEVICE_REMOTE_WAKEUP)
		 */
		set_bit(BTUSB_WAKEUP_DISABLE, &data->flags);
	}

	if (!reset)
		set_bit(HCI_QUIRK_RESET_ON_CLOSE, &hdev->quirks);

	if (force_scofix || id->driver_info & BTUSB_WRONG_SCO_MTU) {
		if (!disable_scofix)
			set_bit(HCI_QUIRK_FIXUP_BUFFER_SIZE, &hdev->quirks);
	}

	if (id->driver_info & BTUSB_BROKEN_ISOC)
		data->isoc = NULL;

	if (id->driver_info & BTUSB_WIDEBAND_SPEECH)
		set_bit(HCI_QUIRK_WIDEBAND_SPEECH_SUPPORTED, &hdev->quirks);

	if (id->driver_info & BTUSB_VALID_LE_STATES)
		set_bit(HCI_QUIRK_VALID_LE_STATES, &hdev->quirks);

	if (id->driver_info & BTUSB_DIGIANSWER) {
		data->cmdreq_type = USB_TYPE_VENDOR;
		set_bit(HCI_QUIRK_RESET_ON_CLOSE, &hdev->quirks);
	}

	if (id->driver_info & BTUSB_CSR) {
		struct usb_device *udev = data->udev;
		u16 bcdDevice = le16_to_cpu(udev->descriptor.bcdDevice);

		/* Old firmware would otherwise execute USB reset */
		if (bcdDevice < 0x117)
			set_bit(HCI_QUIRK_RESET_ON_CLOSE, &hdev->quirks);

		/* This must be set first in case we disable it for fakes */
		set_bit(HCI_QUIRK_SIMULTANEOUS_DISCOVERY, &hdev->quirks);

		/* Fake CSR devices with broken commands */
		if (le16_to_cpu(udev->descriptor.idVendor)  == 0x0a12 &&
		    le16_to_cpu(udev->descriptor.idProduct) == 0x0001)
			hdev->setup = btusb_setup_csr;
	}

	if (id->driver_info & BTUSB_SNIFFER) {
		struct usb_device *udev = data->udev;

		/* New sniffer firmware has crippled HCI interface */
		if (le16_to_cpu(udev->descriptor.bcdDevice) > 0x997)
			set_bit(HCI_QUIRK_RAW_DEVICE, &hdev->quirks);
	}

	if (id->driver_info & BTUSB_INTEL_BOOT) {
		/* A bug in the bootloader causes that interrupt interface is
		 * only enabled after receiving SetInterface(0, AltSetting=0).
		 */
		err = usb_set_interface(data->udev, 0, 0);
		if (err < 0) {
			BT_ERR("failed to set interface 0, alt 0 %d", err);
			goto out_free_dev;
		}
	}

	if (data->isoc) {
		err = usb_driver_claim_interface(&btusb_driver,
						 data->isoc, data);
		if (err < 0)
			goto out_free_dev;
	}

	if (IS_ENABLED(CONFIG_BT_HCIBTUSB_BCM) && data->diag) {
		if (!usb_driver_claim_interface(&btusb_driver,
						data->diag, data))
			__set_diag_interface(hdev);
		else
			data->diag = NULL;
	}

	if (!enable_autosuspend)
		usb_disable_autosuspend(data->udev);

	err = hci_register_dev(hdev);
	if (err < 0)
		goto out_free_dev;

	usb_set_intfdata(intf, data);

	return 0;

out_free_dev:
	if (data->reset_gpio)
		gpiod_put(data->reset_gpio);
	hci_free_dev(hdev);
	return err;
}

static void btusb_disconnect(struct usb_interface *intf)
{
	struct btusb_data *data = usb_get_intfdata(intf);
	struct hci_dev *hdev;

	BT_DBG("intf %p", intf);

	if (!data)
		return;

	hdev = data->hdev;
	usb_set_intfdata(data->intf, NULL);

	if (data->isoc)
		usb_set_intfdata(data->isoc, NULL);

	if (data->diag)
		usb_set_intfdata(data->diag, NULL);

	hci_unregister_dev(hdev);

	if (intf == data->intf) {
		if (data->isoc)
			usb_driver_release_interface(&btusb_driver, data->isoc);
		if (data->diag)
			usb_driver_release_interface(&btusb_driver, data->diag);
	} else if (intf == data->isoc) {
		if (data->diag)
			usb_driver_release_interface(&btusb_driver, data->diag);
		usb_driver_release_interface(&btusb_driver, data->intf);
	} else if (intf == data->diag) {
		usb_driver_release_interface(&btusb_driver, data->intf);
		if (data->isoc)
			usb_driver_release_interface(&btusb_driver, data->isoc);
	}

	if (data->oob_wake_irq)
		device_init_wakeup(&data->udev->dev, false);

	if (data->reset_gpio)
		gpiod_put(data->reset_gpio);

	hci_free_dev(hdev);

	if (!enable_autosuspend)
		usb_enable_autosuspend(data->udev);
}

#ifdef CONFIG_PM
static int btusb_suspend(struct usb_interface *intf, pm_message_t message)
{
	struct btusb_data *data = usb_get_intfdata(intf);

	BT_DBG("intf %p", intf);

	if (data->suspend_count++)
		return 0;

	spin_lock_irq(&data->txlock);
	if (!(PMSG_IS_AUTO(message) && data->tx_in_flight)) {
		set_bit(BTUSB_SUSPENDING, &data->flags);
		spin_unlock_irq(&data->txlock);
	} else {
		spin_unlock_irq(&data->txlock);
		data->suspend_count--;
		return -EBUSY;
	}

	cancel_work_sync(&data->work);

	btusb_stop_traffic(data);
	usb_kill_anchored_urbs(&data->tx_anchor);

	if (data->oob_wake_irq && device_may_wakeup(&data->udev->dev)) {
		set_bit(BTUSB_OOB_WAKE_ENABLED, &data->flags);
		enable_irq_wake(data->oob_wake_irq);
		enable_irq(data->oob_wake_irq);
	}

	/* For global suspend, Realtek devices lose the loaded fw
	 * in them. But for autosuspend, firmware should remain.
	 * Actually, it depends on whether the usb host sends
	 * set feature (enable wakeup) or not.
	 */
	if (test_bit(BTUSB_WAKEUP_DISABLE, &data->flags)) {
		if (PMSG_IS_AUTO(message) &&
		    device_can_wakeup(&data->udev->dev))
			data->udev->do_remote_wakeup = 1;
		else if (!PMSG_IS_AUTO(message))
			data->udev->reset_resume = 1;
	}

	return 0;
}

static void play_deferred(struct btusb_data *data)
{
	struct urb *urb;
	int err;

	while ((urb = usb_get_from_anchor(&data->deferred))) {
		usb_anchor_urb(urb, &data->tx_anchor);

		err = usb_submit_urb(urb, GFP_ATOMIC);
		if (err < 0) {
			if (err != -EPERM && err != -ENODEV)
				BT_ERR("%s urb %p submission failed (%d)",
				       data->hdev->name, urb, -err);
			kfree(urb->setup_packet);
			usb_unanchor_urb(urb);
			usb_free_urb(urb);
			break;
		}

		data->tx_in_flight++;
		usb_free_urb(urb);
	}

	/* Cleanup the rest deferred urbs. */
	while ((urb = usb_get_from_anchor(&data->deferred))) {
		kfree(urb->setup_packet);
		usb_free_urb(urb);
	}
}

static int btusb_resume(struct usb_interface *intf)
{
	struct btusb_data *data = usb_get_intfdata(intf);
	struct hci_dev *hdev = data->hdev;
	int err = 0;

	BT_DBG("intf %p", intf);

	if (--data->suspend_count)
		return 0;

	/* Disable only if not already disabled (keep it balanced) */
	if (test_and_clear_bit(BTUSB_OOB_WAKE_ENABLED, &data->flags)) {
		disable_irq(data->oob_wake_irq);
		disable_irq_wake(data->oob_wake_irq);
	}

	if (!test_bit(HCI_RUNNING, &hdev->flags))
		goto done;

	if (test_bit(BTUSB_INTR_RUNNING, &data->flags)) {
		err = btusb_submit_intr_urb(hdev, GFP_NOIO);
		if (err < 0) {
			clear_bit(BTUSB_INTR_RUNNING, &data->flags);
			goto failed;
		}
	}

	if (test_bit(BTUSB_BULK_RUNNING, &data->flags)) {
		err = btusb_submit_bulk_urb(hdev, GFP_NOIO);
		if (err < 0) {
			clear_bit(BTUSB_BULK_RUNNING, &data->flags);
			goto failed;
		}

		btusb_submit_bulk_urb(hdev, GFP_NOIO);
	}

	if (test_bit(BTUSB_ISOC_RUNNING, &data->flags)) {
		if (btusb_submit_isoc_urb(hdev, GFP_NOIO) < 0)
			clear_bit(BTUSB_ISOC_RUNNING, &data->flags);
		else
			btusb_submit_isoc_urb(hdev, GFP_NOIO);
	}

	spin_lock_irq(&data->txlock);
	play_deferred(data);
	clear_bit(BTUSB_SUSPENDING, &data->flags);
	spin_unlock_irq(&data->txlock);
	schedule_work(&data->work);

	return 0;

failed:
	usb_scuttle_anchored_urbs(&data->deferred);
done:
	spin_lock_irq(&data->txlock);
	clear_bit(BTUSB_SUSPENDING, &data->flags);
	spin_unlock_irq(&data->txlock);

	return err;
}
#endif

static struct usb_driver btusb_driver = {
	.name		= "btusb",
	.probe		= btusb_probe,
	.disconnect	= btusb_disconnect,
#ifdef CONFIG_PM
	.suspend	= btusb_suspend,
	.resume		= btusb_resume,
#endif
	.id_table	= btusb_table,
	.supports_autosuspend = 1,
	.disable_hub_initiated_lpm = 1,
};

module_usb_driver(btusb_driver);

module_param(disable_scofix, bool, 0644);
MODULE_PARM_DESC(disable_scofix, "Disable fixup of wrong SCO buffer size");

module_param(force_scofix, bool, 0644);
MODULE_PARM_DESC(force_scofix, "Force fixup of wrong SCO buffers size");

module_param(enable_autosuspend, bool, 0644);
MODULE_PARM_DESC(enable_autosuspend, "Enable USB autosuspend by default");

module_param(reset, bool, 0644);
MODULE_PARM_DESC(reset, "Send HCI reset command on initialization");

MODULE_AUTHOR("Marcel Holtmann <marcel@holtmann.org>");
MODULE_DESCRIPTION("Generic Bluetooth USB driver ver " VERSION);
MODULE_VERSION(VERSION);
MODULE_LICENSE("GPL");