diff --git a/Documentation/s390/cds.txt b/Documentation/s390/cds.txt
index d939717..f0be389 100644
--- a/Documentation/s390/cds.txt
+++ b/Documentation/s390/cds.txt
@@ -56,12 +56,16 @@
    read device characteristics
    
 read_conf_data()
+read_conf_data_lpm()
    read configuration data.
 
 ccw_device_get_ciw()
    get commands from extended sense data.
 
 ccw_device_start()	
+ccw_device_start_timeout()
+ccw_device_start_key()
+ccw_device_start_key_timeout()
    initiate an I/O request.
 
 ccw_device_resume()
@@ -197,19 +201,21 @@
           operational.
 
 
-read_conf_data() - Read Configuration Data
+read_conf_data(), read_conf_data_lpm() - Read Configuration Data
 
 Retrieve the device dependent configuration data. Please have a look at your 
 device dependent I/O commands for the device specific layout of the node 
-descriptor elements. 
+descriptor elements. read_conf_data_lpm() will retrieve the configuration data
+for a specific path.
 
-The function is meant to be called with an irq handler in place; that is,
+The function is meant to be called with the device already enabled; that is,
 at earliest during set_online() processing.
 
 The function may be called enabled or disabled, but the device must not be
 locked
 
-int read_conf_data(struct ccw_device, void **buffer, int *length, __u8 lpm);
+int read_conf_data(struct ccw_device, void **buffer, int *length);
+int read_conf_data_lpm(struct ccw_device, void **buffer, int *length, __u8 lpm);
 
 cdev   - the ccw_device the data is requested for.
 buffer - Pointer to a buffer pointer. The read_conf_data() routine
@@ -263,6 +269,25 @@
 		     unsigned long intparm,
 		     __u8 lpm,
 		     unsigned long flags);
+int ccw_device_start_timeout(struct ccw_device *cdev,
+			     struct ccw1 *cpa,
+			     unsigned long intparm,
+			     __u8 lpm,
+			     unsigned long flags,
+			     int expires);
+int ccw_device_start_key(struct ccw_device *cdev,
+			 struct ccw1 *cpa,
+			 unsigned long intparm,
+			 __u8 lpm,
+			 __u8 key,
+			 unsigned long flags);
+int ccw_device_start_key_timeout(struct ccw_device *cdev,
+				 struct ccw1 *cpa,
+				 unsigned long intparm,
+				 __u8 lpm,
+				 __u8 key,
+				 unsigned long flags,
+				 int expires);
 
 cdev         : ccw_device the I/O is destined for
 cpa          : logical start address of channel program
@@ -272,7 +297,12 @@
                particular I/O request.
 lpm          : defines the channel path to be used for a specific I/O
                request. A value of 0 will make cio use the opm.
+key	     : the storage key to use for the I/O (useful for operating on a
+	       storage with a storage key != default key)
 flag         : defines the action to be performed for I/O processing
+expires      : timeout value in jiffies. The common I/O layer will terminate
+	       the running program after this and call the interrupt handler
+	       with ERR_PTR(-ETIMEDOUT) as irb.
 
 Possible flag values are :
 
@@ -327,6 +357,13 @@
 interrupt will be presented to indicate I/O completion as the I/O request was
 never started, even though ccw_device_start() returned with successful completion.
 
+The irb may contain an error value, and the device driver should check for this
+first:
+
+-ETIMEDOUT: the common I/O layer terminated the request after the specified
+            timeout value
+-EIO:       the common I/O layer terminated the request due to an error state
+
 If the concurrent sense flag in the extended status word in the irb is set, the
 field irb->scsw.count describes the numer of device specific sense bytes
 available in the extended control word irb->scsw.ecw[0]. No device sensing by