docs: hwmon: mp2975.rst: address some html build warnings
.../Documentation/hwmon/mp2975.rst:25: WARNING: Unexpected indentation.
.../Documentation/hwmon/mp2975.rst:27: WARNING: Block quote ends without a blank line; unexpected unindent.
.../Documentation/hwmon/mp2975.rst:69: WARNING: Unexpected indentation.
.../Documentation/hwmon/mp2975.rst:70: WARNING: Block quote ends without a blank line; unexpected unindent.
.../Documentation/hwmon/mp2975.rst:72: WARNING: Bullet list ends without a blank line; unexpected unindent.
.../Documentation/hwmon/mp2975.rst: WARNING: document isn't included in any toctree
List blocks should have blank lines before and after them,
in order to be properly parsed.
Fixes: 4beb7a028e9f ("hwmon: (pmbus) Add support for MPS Multi-phase mp2975 controller")
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/b02f98d886ab1f5af233f8999c7a15529fc52cdc.1603791716.git.mchehab+huawei@kernel.org
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
diff --git a/Documentation/hwmon/mp2975.rst b/Documentation/hwmon/mp2975.rst
index 5b0609c..81d816b 100644
--- a/Documentation/hwmon/mp2975.rst
+++ b/Documentation/hwmon/mp2975.rst
@@ -20,6 +20,7 @@
vendor dual-loop, digital, multi-phase controller MP2975.
This device:
+
- Supports up to two power rail.
- Provides 8 pulse-width modulations (PWMs), and can be configured up
to 8-phase operation for rail 1 and up to 4-phase operation for rail
@@ -32,10 +33,12 @@
10-mV DAC, IMVP9 mode with 5-mV DAC.
Device supports:
+
- SVID interface.
- AVSBus interface.
Device complaint with:
+
- PMBus rev 1.3 interface.
Device supports direct format for reading output current, output voltage,
@@ -45,11 +48,14 @@
The below VID modes are supported: VR12, VR13, IMVP9.
The driver provides the next attributes for the current:
+
- for current in: input, maximum alarm;
- for current out input, maximum alarm and highest values;
- for phase current: input and label.
-attributes.
+ attributes.
+
The driver exports the following attributes via the 'sysfs' files, where
+
- 'n' is number of telemetry pages (from 1 to 2);
- 'k' is number of configured phases (from 1 to 8);
- indexes 1, 1*n for "iin";
@@ -65,11 +71,14 @@
**curr[1-{2n+k}]_label**
The driver provides the next attributes for the voltage:
+
- for voltage in: input, high critical threshold, high critical alarm, all only
from page 0;
- for voltage out: input, low and high critical thresholds, low and high
critical alarms, from pages 0 and 1;
+
The driver exports the following attributes via the 'sysfs' files, where
+
- 'n' is number of telemetry pages (from 1 to 2);
- indexes 1 for "iin";
- indexes n+1, n+2 for "vout";
@@ -87,9 +96,12 @@
**in[2-{n+1}1_lcrit_alarm**
The driver provides the next attributes for the power:
+
- for power in alarm and input.
- for power out: highest and input.
+
The driver exports the following attributes via the 'sysfs' files, where
+
- 'n' is number of telemetry pages (from 1 to 2);
- indexes 1 for "pin";
- indexes n+1, n+2 for "pout";