i2c: Bus drivers return -Errno not -1
Tighten error paths used by various i2c adapters (mostly x86) so
they return real fault/errno codes instead of a "-1" (which is
most often interpreted as "-EPERM"). Build tested, with eyeball
review.
One minor initial goal is to have adapters consistently return
the code "-ENXIO" when addressing a device doesn't get an ACK
response, at least in the probe paths where they are already
good at stifling related logspam.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
diff --git a/drivers/i2c/busses/i2c-sis630.c b/drivers/i2c/busses/i2c-sis630.c
index 3765dd7..c4cc5ed 100644
--- a/drivers/i2c/busses/i2c-sis630.c
+++ b/drivers/i2c/busses/i2c-sis630.c
@@ -134,7 +134,7 @@
if ((temp = sis630_read(SMB_CNT) & 0x03) != 0x00) {
dev_dbg(&adap->dev, "Failed! (%02x)\n", temp);
- return -1;
+ return -EBUSY;
} else {
dev_dbg(&adap->dev, "Successful!\n");
}
@@ -177,17 +177,17 @@
/* If the SMBus is still busy, we give up */
if (timeout >= MAX_TIMEOUT) {
dev_dbg(&adap->dev, "SMBus Timeout!\n");
- result = -1;
+ result = -ETIMEDOUT;
}
if (temp & 0x02) {
dev_dbg(&adap->dev, "Error: Failed bus transaction\n");
- result = -1;
+ result = -ENXIO;
}
if (temp & 0x04) {
dev_err(&adap->dev, "Bus collision!\n");
- result = -1;
+ result = -EIO;
/*
TBD: Datasheet say:
the software should clear this bit and restart SMBUS operation.
@@ -250,8 +250,10 @@
if (i==8 || (len<8 && i==len)) {
dev_dbg(&adap->dev, "start trans len=%d i=%d\n",len ,i);
/* first transaction */
- if (sis630_transaction_start(adap, SIS630_BLOCK_DATA, &oldclock))
- return -1;
+ rc = sis630_transaction_start(adap,
+ SIS630_BLOCK_DATA, &oldclock);
+ if (rc)
+ return rc;
}
else if ((i-1)%8 == 7 || i==len) {
dev_dbg(&adap->dev, "trans_wait len=%d i=%d\n",len,i);
@@ -264,9 +266,10 @@
*/
sis630_write(SMB_STS,0x10);
}
- if (sis630_transaction_wait(adap, SIS630_BLOCK_DATA)) {
+ rc = sis630_transaction_wait(adap,
+ SIS630_BLOCK_DATA);
+ if (rc) {
dev_dbg(&adap->dev, "trans_wait failed\n");
- rc = -1;
break;
}
}
@@ -275,13 +278,14 @@
else {
/* read request */
data->block[0] = len = 0;
- if (sis630_transaction_start(adap, SIS630_BLOCK_DATA, &oldclock)) {
- return -1;
- }
+ rc = sis630_transaction_start(adap,
+ SIS630_BLOCK_DATA, &oldclock);
+ if (rc)
+ return rc;
do {
- if (sis630_transaction_wait(adap, SIS630_BLOCK_DATA)) {
+ rc = sis630_transaction_wait(adap, SIS630_BLOCK_DATA);
+ if (rc) {
dev_dbg(&adap->dev, "trans_wait failed\n");
- rc = -1;
break;
}
/* if this first transaction then read byte count */
@@ -311,11 +315,13 @@
return rc;
}
-/* Return -1 on error. */
+/* Return negative errno on error. */
static s32 sis630_access(struct i2c_adapter *adap, u16 addr,
unsigned short flags, char read_write,
u8 command, int size, union i2c_smbus_data *data)
{
+ int status;
+
switch (size) {
case I2C_SMBUS_QUICK:
sis630_write(SMB_ADDR, ((addr & 0x7f) << 1) | (read_write & 0x01));
@@ -350,13 +356,13 @@
size = SIS630_BLOCK_DATA;
return sis630_block_data(adap, data, read_write);
default:
- printk("Unsupported I2C size\n");
- return -1;
- break;
+ printk("Unsupported SMBus operation\n");
+ return -EOPNOTSUPP;
}
- if (sis630_transaction(adap, size))
- return -1;
+ status = sis630_transaction(adap, size);
+ if (status)
+ return status;
if ((size != SIS630_PCALL) &&
((read_write == I2C_SMBUS_WRITE) || (size == SIS630_QUICK))) {
@@ -373,8 +379,7 @@
data->word = sis630_read(SMB_BYTE) + (sis630_read(SMB_BYTE + 1) << 8);
break;
default:
- return -1;
- break;
+ return -EOPNOTSUPP;
}
return 0;