Merge series "spi-bcm-qspi spcr3 enahancements" from Kamal Dasu <kdasu.kdev@gmail.com>:
This change set feature enahancements for spcr3 transfer modes as well as
adds support for half-duplex 3-wire mode transfer.
Kamal Dasu (3):
spi: bcm-qspi: Add mspi spcr3 32/64-bits xfer mode
spi: bcm-qspi: clear MSPI spifie interrupt during probe
spi: bcm-qspi: add support for 3-wire mode for half duplex transfer
drivers/spi/spi-bcm-qspi.c | 262 +++++++++++++++++++++++++++++--------
1 file changed, 208 insertions(+), 54 deletions(-)
--
2.17.1
diff --git a/drivers/spi/spi-bcm-qspi.c b/drivers/spi/spi-bcm-qspi.c
index 0d95fe5..6cf7cff 100644
--- a/drivers/spi/spi-bcm-qspi.c
+++ b/drivers/spi/spi-bcm-qspi.c
@@ -83,6 +83,9 @@
/* MSPI register offsets */
#define MSPI_SPCR0_LSB 0x000
#define MSPI_SPCR0_MSB 0x004
+#define MSPI_SPCR0_MSB_CPHA BIT(0)
+#define MSPI_SPCR0_MSB_CPOL BIT(1)
+#define MSPI_SPCR0_MSB_BITS_SHIFT 0x2
#define MSPI_SPCR1_LSB 0x008
#define MSPI_SPCR1_MSB 0x00c
#define MSPI_NEWQP 0x010
@@ -100,8 +103,10 @@
#define MSPI_MASTER_BIT BIT(7)
#define MSPI_NUM_CDRAM 16
+#define MSPI_CDRAM_OUTP BIT(8)
#define MSPI_CDRAM_CONT_BIT BIT(7)
#define MSPI_CDRAM_BITSE_BIT BIT(6)
+#define MSPI_CDRAM_DT_BIT BIT(5)
#define MSPI_CDRAM_PCS 0xf
#define MSPI_SPCR2_SPE BIT(6)
@@ -114,6 +119,14 @@
~(BIT(10) | BIT(11)))
#define MSPI_SPCR3_SYSCLKSEL_108 (MSPI_SPCR3_SYSCLKSEL_MASK & \
BIT(11))
+#define MSPI_SPCR3_TXRXDAM_MASK GENMASK(4, 2)
+#define MSPI_SPCR3_DAM_8BYTE 0
+#define MSPI_SPCR3_DAM_16BYTE (BIT(2) | BIT(4))
+#define MSPI_SPCR3_DAM_32BYTE (BIT(3) | BIT(5))
+#define MSPI_SPCR3_HALFDUPLEX BIT(6)
+#define MSPI_SPCR3_HDOUTTYPE BIT(7)
+#define MSPI_SPCR3_DATA_REG_SZ BIT(8)
+#define MSPI_SPCR3_CPHARX BIT(9)
#define MSPI_MSPI_STATUS_SPIF BIT(0)
@@ -153,6 +166,14 @@
#define TRANS_STATUS_BREAK_DESELECT (TRANS_STATUS_BREAK_EOM | \
TRANS_STATUS_BREAK_CS_CHANGE)
+/*
+ * Used for writing and reading data in the right order
+ * to TXRAM and RXRAM when used as 32-bit registers respectively
+ */
+#define swap4bytes(__val) \
+ ((((__val) >> 24) & 0x000000FF) | (((__val) >> 8) & 0x0000FF00) | \
+ (((__val) << 8) & 0x00FF0000) | (((__val) << 24) & 0xFF000000))
+
struct bcm_qspi_parms {
u32 speed_hz;
u8 mode;
@@ -261,7 +282,7 @@ static inline bool bcm_qspi_has_sysclk_108(struct bcm_qspi *qspi)
static inline int bcm_qspi_spbr_min(struct bcm_qspi *qspi)
{
if (bcm_qspi_has_fastbr(qspi))
- return 1;
+ return (bcm_qspi_has_sysclk_108(qspi) ? 4 : 1);
else
return 8;
}
@@ -571,23 +592,23 @@ static void bcm_qspi_hw_set_parms(struct bcm_qspi *qspi,
{
u32 spcr, spbr = 0;
- if (xp->speed_hz)
- spbr = qspi->base_clk / (2 * xp->speed_hz);
-
- spcr = clamp_val(spbr, bcm_qspi_spbr_min(qspi), QSPI_SPBR_MAX);
- bcm_qspi_write(qspi, MSPI, MSPI_SPCR0_LSB, spcr);
-
if (!qspi->mspi_maj_rev)
/* legacy controller */
spcr = MSPI_MASTER_BIT;
else
spcr = 0;
- /* for 16 bit the data should be zero */
- if (xp->bits_per_word != 16)
- spcr |= xp->bits_per_word << 2;
- spcr |= xp->mode & 3;
+ /*
+ * Bits per transfer. BITS determines the number of data bits
+ * transferred if the command control bit (BITSE of a
+ * CDRAM Register) is equal to 1.
+ * If CDRAM BITSE is equal to 0, 8 data bits are transferred
+ * regardless
+ */
+ if (xp->bits_per_word != 16 && xp->bits_per_word != 64)
+ spcr |= xp->bits_per_word << MSPI_SPCR0_MSB_BITS_SHIFT;
+ spcr |= xp->mode & (MSPI_SPCR0_MSB_CPHA | MSPI_SPCR0_MSB_CPOL);
bcm_qspi_write(qspi, MSPI, MSPI_SPCR0_MSB, spcr);
if (bcm_qspi_has_fastbr(qspi)) {
@@ -596,17 +617,44 @@ static void bcm_qspi_hw_set_parms(struct bcm_qspi *qspi,
/* enable fastbr */
spcr |= MSPI_SPCR3_FASTBR;
+ if (xp->mode & SPI_3WIRE)
+ spcr |= MSPI_SPCR3_HALFDUPLEX | MSPI_SPCR3_HDOUTTYPE;
+
if (bcm_qspi_has_sysclk_108(qspi)) {
/* SYSCLK_108 */
spcr |= MSPI_SPCR3_SYSCLKSEL_108;
qspi->base_clk = MSPI_BASE_FREQ * 4;
- /* Change spbr as we changed sysclk */
- bcm_qspi_write(qspi, MSPI, MSPI_SPCR0_LSB, 4);
}
+ if (xp->bits_per_word > 16) {
+ /* data_reg_size 1 (64bit) */
+ spcr |= MSPI_SPCR3_DATA_REG_SZ;
+ /* TxRx RAM data access mode 2 for 32B and set fastdt */
+ spcr |= MSPI_SPCR3_DAM_32BYTE | MSPI_SPCR3_FASTDT;
+ /*
+ * Set length of delay after transfer
+ * DTL from 0(256) to 1
+ */
+ bcm_qspi_write(qspi, MSPI, MSPI_SPCR1_LSB, 1);
+ } else {
+ /* data_reg_size[8] = 0 */
+ spcr &= ~(MSPI_SPCR3_DATA_REG_SZ);
+
+ /*
+ * TxRx RAM access mode 8B
+ * and disable fastdt
+ */
+ spcr &= ~(MSPI_SPCR3_DAM_32BYTE);
+ }
bcm_qspi_write(qspi, MSPI, MSPI_SPCR3, spcr);
}
+ if (xp->speed_hz)
+ spbr = qspi->base_clk / (2 * xp->speed_hz);
+
+ spbr = clamp_val(spbr, bcm_qspi_spbr_min(qspi), QSPI_SPBR_MAX);
+ bcm_qspi_write(qspi, MSPI, MSPI_SPCR0_LSB, spbr);
+
qspi->last_parms = *xp;
}
@@ -627,7 +675,7 @@ static int bcm_qspi_setup(struct spi_device *spi)
{
struct bcm_qspi_parms *xp;
- if (spi->bits_per_word > 16)
+ if (spi->bits_per_word > 64)
return -EINVAL;
xp = spi_get_ctldata(spi);
@@ -666,8 +714,12 @@ static int update_qspi_trans_byte_count(struct bcm_qspi *qspi,
/* count the last transferred bytes */
if (qt->trans->bits_per_word <= 8)
qt->byte++;
- else
+ else if (qt->trans->bits_per_word <= 16)
qt->byte += 2;
+ else if (qt->trans->bits_per_word <= 32)
+ qt->byte += 4;
+ else if (qt->trans->bits_per_word <= 64)
+ qt->byte += 8;
if (qt->byte >= qt->trans->len) {
/* we're at the end of the spi_transfer */
@@ -710,6 +762,33 @@ static inline u16 read_rxram_slot_u16(struct bcm_qspi *qspi, int slot)
((bcm_qspi_read(qspi, MSPI, msb_offset) & 0xff) << 8);
}
+static inline u32 read_rxram_slot_u32(struct bcm_qspi *qspi, int slot)
+{
+ u32 reg_offset = MSPI_RXRAM;
+ u32 offset = reg_offset + (slot << 3);
+ u32 val;
+
+ val = bcm_qspi_read(qspi, MSPI, offset);
+ val = swap4bytes(val);
+
+ return val;
+}
+
+static inline u64 read_rxram_slot_u64(struct bcm_qspi *qspi, int slot)
+{
+ u32 reg_offset = MSPI_RXRAM;
+ u32 lsb_offset = reg_offset + (slot << 3) + 0x4;
+ u32 msb_offset = reg_offset + (slot << 3);
+ u32 msb, lsb;
+
+ msb = bcm_qspi_read(qspi, MSPI, msb_offset);
+ msb = swap4bytes(msb);
+ lsb = bcm_qspi_read(qspi, MSPI, lsb_offset);
+ lsb = swap4bytes(lsb);
+
+ return ((u64)msb << 32 | lsb);
+}
+
static void read_from_hw(struct bcm_qspi *qspi, int slots)
{
struct qspi_trans tp;
@@ -733,7 +812,7 @@ static void read_from_hw(struct bcm_qspi *qspi, int slots)
buf[tp.byte] = read_rxram_slot_u8(qspi, slot);
dev_dbg(&qspi->pdev->dev, "RD %02x\n",
buf ? buf[tp.byte] : 0x0);
- } else {
+ } else if (tp.trans->bits_per_word <= 16) {
u16 *buf = tp.trans->rx_buf;
if (buf)
@@ -741,6 +820,25 @@ static void read_from_hw(struct bcm_qspi *qspi, int slots)
slot);
dev_dbg(&qspi->pdev->dev, "RD %04x\n",
buf ? buf[tp.byte / 2] : 0x0);
+ } else if (tp.trans->bits_per_word <= 32) {
+ u32 *buf = tp.trans->rx_buf;
+
+ if (buf)
+ buf[tp.byte / 4] = read_rxram_slot_u32(qspi,
+ slot);
+ dev_dbg(&qspi->pdev->dev, "RD %08x\n",
+ buf ? buf[tp.byte / 4] : 0x0);
+
+ } else if (tp.trans->bits_per_word <= 64) {
+ u64 *buf = tp.trans->rx_buf;
+
+ if (buf)
+ buf[tp.byte / 8] = read_rxram_slot_u64(qspi,
+ slot);
+ dev_dbg(&qspi->pdev->dev, "RD %llx\n",
+ buf ? buf[tp.byte / 8] : 0x0);
+
+
}
update_qspi_trans_byte_count(qspi, &tp,
@@ -770,6 +868,28 @@ static inline void write_txram_slot_u16(struct bcm_qspi *qspi, int slot,
bcm_qspi_write(qspi, MSPI, lsb_offset, (val & 0xff));
}
+static inline void write_txram_slot_u32(struct bcm_qspi *qspi, int slot,
+ u32 val)
+{
+ u32 reg_offset = MSPI_TXRAM;
+ u32 msb_offset = reg_offset + (slot << 3);
+
+ bcm_qspi_write(qspi, MSPI, msb_offset, swap4bytes(val));
+}
+
+static inline void write_txram_slot_u64(struct bcm_qspi *qspi, int slot,
+ u64 val)
+{
+ u32 reg_offset = MSPI_TXRAM;
+ u32 msb_offset = reg_offset + (slot << 3);
+ u32 lsb_offset = reg_offset + (slot << 3) + 0x4;
+ u32 msb = upper_32_bits(val);
+ u32 lsb = lower_32_bits(val);
+
+ bcm_qspi_write(qspi, MSPI, msb_offset, swap4bytes(msb));
+ bcm_qspi_write(qspi, MSPI, lsb_offset, swap4bytes(lsb));
+}
+
static inline u32 read_cdram_slot(struct bcm_qspi *qspi, int slot)
{
return bcm_qspi_read(qspi, MSPI, MSPI_CDRAM + (slot << 2));
@@ -793,20 +913,43 @@ static int write_to_hw(struct bcm_qspi *qspi, struct spi_device *spi)
/* Run until end of transfer or reached the max data */
while (!tstatus && slot < MSPI_NUM_CDRAM) {
+ mspi_cdram = MSPI_CDRAM_CONT_BIT;
if (tp.trans->bits_per_word <= 8) {
const u8 *buf = tp.trans->tx_buf;
u8 val = buf ? buf[tp.byte] : 0x00;
write_txram_slot_u8(qspi, slot, val);
dev_dbg(&qspi->pdev->dev, "WR %02x\n", val);
- } else {
+ } else if (tp.trans->bits_per_word <= 16) {
const u16 *buf = tp.trans->tx_buf;
u16 val = buf ? buf[tp.byte / 2] : 0x0000;
write_txram_slot_u16(qspi, slot, val);
dev_dbg(&qspi->pdev->dev, "WR %04x\n", val);
+ } else if (tp.trans->bits_per_word <= 32) {
+ const u32 *buf = tp.trans->tx_buf;
+ u32 val = buf ? buf[tp.byte/4] : 0x0;
+
+ write_txram_slot_u32(qspi, slot, val);
+ dev_dbg(&qspi->pdev->dev, "WR %08x\n", val);
+ } else if (tp.trans->bits_per_word <= 64) {
+ const u64 *buf = tp.trans->tx_buf;
+ u64 val = (buf ? buf[tp.byte/8] : 0x0);
+
+ /* use the length of delay from SPCR1_LSB */
+ if (bcm_qspi_has_fastbr(qspi))
+ mspi_cdram |= MSPI_CDRAM_DT_BIT;
+
+ write_txram_slot_u64(qspi, slot, val);
+ dev_dbg(&qspi->pdev->dev, "WR %llx\n", val);
}
- mspi_cdram = MSPI_CDRAM_CONT_BIT;
+
+ mspi_cdram |= ((tp.trans->bits_per_word <= 8) ? 0 :
+ MSPI_CDRAM_BITSE_BIT);
+
+ /* set 3wrire halfduplex mode data from master to slave */
+ if ((spi->mode & SPI_3WIRE) && tp.trans->tx_buf)
+ mspi_cdram |= MSPI_CDRAM_OUTP;
if (has_bspi(qspi))
mspi_cdram &= ~1;
@@ -814,9 +957,6 @@ static int write_to_hw(struct bcm_qspi *qspi, struct spi_device *spi)
mspi_cdram |= (~(1 << spi->chip_select) &
MSPI_CDRAM_PCS);
- mspi_cdram |= ((tp.trans->bits_per_word <= 8) ? 0 :
- MSPI_CDRAM_BITSE_BIT);
-
write_cdram_slot(qspi, slot, mspi_cdram);
tstatus = update_qspi_trans_byte_count(qspi, &tp,
@@ -1251,10 +1391,14 @@ static void bcm_qspi_hw_init(struct bcm_qspi *qspi)
static void bcm_qspi_hw_uninit(struct bcm_qspi *qspi)
{
+ u32 status = bcm_qspi_read(qspi, MSPI, MSPI_MSPI_STATUS);
+
bcm_qspi_write(qspi, MSPI, MSPI_SPCR2, 0);
if (has_bspi(qspi))
bcm_qspi_write(qspi, MSPI, MSPI_WRITE_LOCK, 0);
+ /* clear interrupt */
+ bcm_qspi_write(qspi, MSPI, MSPI_MSPI_STATUS, status & ~1);
}
static const struct spi_controller_mem_ops bcm_qspi_mem_ops = {
@@ -1347,7 +1491,8 @@ int bcm_qspi_probe(struct platform_device *pdev,
qspi->master = master;
master->bus_num = -1;
- master->mode_bits = SPI_CPHA | SPI_CPOL | SPI_RX_DUAL | SPI_RX_QUAD;
+ master->mode_bits = SPI_CPHA | SPI_CPOL | SPI_RX_DUAL | SPI_RX_QUAD |
+ SPI_3WIRE;
master->setup = bcm_qspi_setup;
master->transfer_one = bcm_qspi_transfer_one;
master->mem_ops = &bcm_qspi_mem_ops;
@@ -1398,6 +1543,47 @@ int bcm_qspi_probe(struct platform_device *pdev,
if (!qspi->dev_ids)
return -ENOMEM;
+ /*
+ * Some SoCs integrate spi controller (e.g., its interrupt bits)
+ * in specific ways
+ */
+ if (soc_intc) {
+ qspi->soc_intc = soc_intc;
+ soc_intc->bcm_qspi_int_set(soc_intc, MSPI_DONE, true);
+ } else {
+ qspi->soc_intc = NULL;
+ }
+
+ if (qspi->clk) {
+ ret = clk_prepare_enable(qspi->clk);
+ if (ret) {
+ dev_err(dev, "failed to prepare clock\n");
+ goto qspi_probe_err;
+ }
+ qspi->base_clk = clk_get_rate(qspi->clk);
+ } else {
+ qspi->base_clk = MSPI_BASE_FREQ;
+ }
+
+ if (data->has_mspi_rev) {
+ rev = bcm_qspi_read(qspi, MSPI, MSPI_REV);
+ /* some older revs do not have a MSPI_REV register */
+ if ((rev & 0xff) == 0xff)
+ rev = 0;
+ }
+
+ qspi->mspi_maj_rev = (rev >> 4) & 0xf;
+ qspi->mspi_min_rev = rev & 0xf;
+ qspi->mspi_spcr3_sysclk = data->has_spcr3_sysclk;
+
+ qspi->max_speed_hz = qspi->base_clk / (bcm_qspi_spbr_min(qspi) * 2);
+
+ /*
+ * On SW resets it is possible to have the mask still enabled
+ * Need to disable the mask and clear the status while we init
+ */
+ bcm_qspi_hw_uninit(qspi);
+
for (val = 0; val < num_irqs; val++) {
irq = -1;
name = qspi_irq_tab[val].irq_name;
@@ -1434,38 +1620,6 @@ int bcm_qspi_probe(struct platform_device *pdev,
goto qspi_probe_err;
}
- /*
- * Some SoCs integrate spi controller (e.g., its interrupt bits)
- * in specific ways
- */
- if (soc_intc) {
- qspi->soc_intc = soc_intc;
- soc_intc->bcm_qspi_int_set(soc_intc, MSPI_DONE, true);
- } else {
- qspi->soc_intc = NULL;
- }
-
- ret = clk_prepare_enable(qspi->clk);
- if (ret) {
- dev_err(dev, "failed to prepare clock\n");
- goto qspi_probe_err;
- }
-
- qspi->base_clk = clk_get_rate(qspi->clk);
-
- if (data->has_mspi_rev) {
- rev = bcm_qspi_read(qspi, MSPI, MSPI_REV);
- /* some older revs do not have a MSPI_REV register */
- if ((rev & 0xff) == 0xff)
- rev = 0;
- }
-
- qspi->mspi_maj_rev = (rev >> 4) & 0xf;
- qspi->mspi_min_rev = rev & 0xf;
- qspi->mspi_spcr3_sysclk = data->has_spcr3_sysclk;
-
- qspi->max_speed_hz = qspi->base_clk / (bcm_qspi_spbr_min(qspi) * 2);
-
bcm_qspi_hw_init(qspi);
init_completion(&qspi->mspi_done);
init_completion(&qspi->bspi_done);