pinctrl: nomadik: move platform data handling into driver
This decomissions the platform data header (which is no longer
in use after the systems using this driver were switched to
a pure device-tree config path) and merges the result into
the driver file or local driver header.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
diff --git a/drivers/pinctrl/pinctrl-nomadik.c b/drivers/pinctrl/pinctrl-nomadik.c
index 7111c3b..3895f14 100644
--- a/drivers/pinctrl/pinctrl-nomadik.c
+++ b/drivers/pinctrl/pinctrl-nomadik.c
@@ -33,7 +33,6 @@
#include <linux/pinctrl/pinconf.h>
/* Since we request GPIOs from ourself */
#include <linux/pinctrl/consumer.h>
-#include <linux/platform_data/pinctrl-nomadik.h>
#include "pinctrl-nomadik.h"
#include "core.h"
@@ -45,6 +44,221 @@
* Symbols in this file are called "nmk_gpio" for "nomadik gpio"
*/
+/*
+ * pin configurations are represented by 32-bit integers:
+ *
+ * bit 0.. 8 - Pin Number (512 Pins Maximum)
+ * bit 9..10 - Alternate Function Selection
+ * bit 11..12 - Pull up/down state
+ * bit 13 - Sleep mode behaviour
+ * bit 14 - Direction
+ * bit 15 - Value (if output)
+ * bit 16..18 - SLPM pull up/down state
+ * bit 19..20 - SLPM direction
+ * bit 21..22 - SLPM Value (if output)
+ * bit 23..25 - PDIS value (if input)
+ * bit 26 - Gpio mode
+ * bit 27 - Sleep mode
+ *
+ * to facilitate the definition, the following macros are provided
+ *
+ * PIN_CFG_DEFAULT - default config (0):
+ * pull up/down = disabled
+ * sleep mode = input/wakeup
+ * direction = input
+ * value = low
+ * SLPM direction = same as normal
+ * SLPM pull = same as normal
+ * SLPM value = same as normal
+ *
+ * PIN_CFG - default config with alternate function
+ */
+
+typedef unsigned long pin_cfg_t;
+
+#define PIN_NUM_MASK 0x1ff
+#define PIN_NUM(x) ((x) & PIN_NUM_MASK)
+
+#define PIN_ALT_SHIFT 9
+#define PIN_ALT_MASK (0x3 << PIN_ALT_SHIFT)
+#define PIN_ALT(x) (((x) & PIN_ALT_MASK) >> PIN_ALT_SHIFT)
+#define PIN_GPIO (NMK_GPIO_ALT_GPIO << PIN_ALT_SHIFT)
+#define PIN_ALT_A (NMK_GPIO_ALT_A << PIN_ALT_SHIFT)
+#define PIN_ALT_B (NMK_GPIO_ALT_B << PIN_ALT_SHIFT)
+#define PIN_ALT_C (NMK_GPIO_ALT_C << PIN_ALT_SHIFT)
+
+#define PIN_PULL_SHIFT 11
+#define PIN_PULL_MASK (0x3 << PIN_PULL_SHIFT)
+#define PIN_PULL(x) (((x) & PIN_PULL_MASK) >> PIN_PULL_SHIFT)
+#define PIN_PULL_NONE (NMK_GPIO_PULL_NONE << PIN_PULL_SHIFT)
+#define PIN_PULL_UP (NMK_GPIO_PULL_UP << PIN_PULL_SHIFT)
+#define PIN_PULL_DOWN (NMK_GPIO_PULL_DOWN << PIN_PULL_SHIFT)
+
+#define PIN_SLPM_SHIFT 13
+#define PIN_SLPM_MASK (0x1 << PIN_SLPM_SHIFT)
+#define PIN_SLPM(x) (((x) & PIN_SLPM_MASK) >> PIN_SLPM_SHIFT)
+#define PIN_SLPM_MAKE_INPUT (NMK_GPIO_SLPM_INPUT << PIN_SLPM_SHIFT)
+#define PIN_SLPM_NOCHANGE (NMK_GPIO_SLPM_NOCHANGE << PIN_SLPM_SHIFT)
+/* These two replace the above in DB8500v2+ */
+#define PIN_SLPM_WAKEUP_ENABLE (NMK_GPIO_SLPM_WAKEUP_ENABLE << PIN_SLPM_SHIFT)
+#define PIN_SLPM_WAKEUP_DISABLE (NMK_GPIO_SLPM_WAKEUP_DISABLE << PIN_SLPM_SHIFT)
+#define PIN_SLPM_USE_MUX_SETTINGS_IN_SLEEP PIN_SLPM_WAKEUP_DISABLE
+
+#define PIN_SLPM_GPIO PIN_SLPM_WAKEUP_ENABLE /* In SLPM, pin is a gpio */
+#define PIN_SLPM_ALTFUNC PIN_SLPM_WAKEUP_DISABLE /* In SLPM, pin is altfunc */
+
+#define PIN_DIR_SHIFT 14
+#define PIN_DIR_MASK (0x1 << PIN_DIR_SHIFT)
+#define PIN_DIR(x) (((x) & PIN_DIR_MASK) >> PIN_DIR_SHIFT)
+#define PIN_DIR_INPUT (0 << PIN_DIR_SHIFT)
+#define PIN_DIR_OUTPUT (1 << PIN_DIR_SHIFT)
+
+#define PIN_VAL_SHIFT 15
+#define PIN_VAL_MASK (0x1 << PIN_VAL_SHIFT)
+#define PIN_VAL(x) (((x) & PIN_VAL_MASK) >> PIN_VAL_SHIFT)
+#define PIN_VAL_LOW (0 << PIN_VAL_SHIFT)
+#define PIN_VAL_HIGH (1 << PIN_VAL_SHIFT)
+
+#define PIN_SLPM_PULL_SHIFT 16
+#define PIN_SLPM_PULL_MASK (0x7 << PIN_SLPM_PULL_SHIFT)
+#define PIN_SLPM_PULL(x) \
+ (((x) & PIN_SLPM_PULL_MASK) >> PIN_SLPM_PULL_SHIFT)
+#define PIN_SLPM_PULL_NONE \
+ ((1 + NMK_GPIO_PULL_NONE) << PIN_SLPM_PULL_SHIFT)
+#define PIN_SLPM_PULL_UP \
+ ((1 + NMK_GPIO_PULL_UP) << PIN_SLPM_PULL_SHIFT)
+#define PIN_SLPM_PULL_DOWN \
+ ((1 + NMK_GPIO_PULL_DOWN) << PIN_SLPM_PULL_SHIFT)
+
+#define PIN_SLPM_DIR_SHIFT 19
+#define PIN_SLPM_DIR_MASK (0x3 << PIN_SLPM_DIR_SHIFT)
+#define PIN_SLPM_DIR(x) \
+ (((x) & PIN_SLPM_DIR_MASK) >> PIN_SLPM_DIR_SHIFT)
+#define PIN_SLPM_DIR_INPUT ((1 + 0) << PIN_SLPM_DIR_SHIFT)
+#define PIN_SLPM_DIR_OUTPUT ((1 + 1) << PIN_SLPM_DIR_SHIFT)
+
+#define PIN_SLPM_VAL_SHIFT 21
+#define PIN_SLPM_VAL_MASK (0x3 << PIN_SLPM_VAL_SHIFT)
+#define PIN_SLPM_VAL(x) \
+ (((x) & PIN_SLPM_VAL_MASK) >> PIN_SLPM_VAL_SHIFT)
+#define PIN_SLPM_VAL_LOW ((1 + 0) << PIN_SLPM_VAL_SHIFT)
+#define PIN_SLPM_VAL_HIGH ((1 + 1) << PIN_SLPM_VAL_SHIFT)
+
+#define PIN_SLPM_PDIS_SHIFT 23
+#define PIN_SLPM_PDIS_MASK (0x3 << PIN_SLPM_PDIS_SHIFT)
+#define PIN_SLPM_PDIS(x) \
+ (((x) & PIN_SLPM_PDIS_MASK) >> PIN_SLPM_PDIS_SHIFT)
+#define PIN_SLPM_PDIS_NO_CHANGE (0 << PIN_SLPM_PDIS_SHIFT)
+#define PIN_SLPM_PDIS_DISABLED (1 << PIN_SLPM_PDIS_SHIFT)
+#define PIN_SLPM_PDIS_ENABLED (2 << PIN_SLPM_PDIS_SHIFT)
+
+#define PIN_LOWEMI_SHIFT 25
+#define PIN_LOWEMI_MASK (0x1 << PIN_LOWEMI_SHIFT)
+#define PIN_LOWEMI(x) (((x) & PIN_LOWEMI_MASK) >> PIN_LOWEMI_SHIFT)
+#define PIN_LOWEMI_DISABLED (0 << PIN_LOWEMI_SHIFT)
+#define PIN_LOWEMI_ENABLED (1 << PIN_LOWEMI_SHIFT)
+
+#define PIN_GPIOMODE_SHIFT 26
+#define PIN_GPIOMODE_MASK (0x1 << PIN_GPIOMODE_SHIFT)
+#define PIN_GPIOMODE(x) (((x) & PIN_GPIOMODE_MASK) >> PIN_GPIOMODE_SHIFT)
+#define PIN_GPIOMODE_DISABLED (0 << PIN_GPIOMODE_SHIFT)
+#define PIN_GPIOMODE_ENABLED (1 << PIN_GPIOMODE_SHIFT)
+
+#define PIN_SLEEPMODE_SHIFT 27
+#define PIN_SLEEPMODE_MASK (0x1 << PIN_SLEEPMODE_SHIFT)
+#define PIN_SLEEPMODE(x) (((x) & PIN_SLEEPMODE_MASK) >> PIN_SLEEPMODE_SHIFT)
+#define PIN_SLEEPMODE_DISABLED (0 << PIN_SLEEPMODE_SHIFT)
+#define PIN_SLEEPMODE_ENABLED (1 << PIN_SLEEPMODE_SHIFT)
+
+
+/* Shortcuts. Use these instead of separate DIR, PULL, and VAL. */
+#define PIN_INPUT_PULLDOWN (PIN_DIR_INPUT | PIN_PULL_DOWN)
+#define PIN_INPUT_PULLUP (PIN_DIR_INPUT | PIN_PULL_UP)
+#define PIN_INPUT_NOPULL (PIN_DIR_INPUT | PIN_PULL_NONE)
+#define PIN_OUTPUT_LOW (PIN_DIR_OUTPUT | PIN_VAL_LOW)
+#define PIN_OUTPUT_HIGH (PIN_DIR_OUTPUT | PIN_VAL_HIGH)
+
+#define PIN_SLPM_INPUT_PULLDOWN (PIN_SLPM_DIR_INPUT | PIN_SLPM_PULL_DOWN)
+#define PIN_SLPM_INPUT_PULLUP (PIN_SLPM_DIR_INPUT | PIN_SLPM_PULL_UP)
+#define PIN_SLPM_INPUT_NOPULL (PIN_SLPM_DIR_INPUT | PIN_SLPM_PULL_NONE)
+#define PIN_SLPM_OUTPUT_LOW (PIN_SLPM_DIR_OUTPUT | PIN_SLPM_VAL_LOW)
+#define PIN_SLPM_OUTPUT_HIGH (PIN_SLPM_DIR_OUTPUT | PIN_SLPM_VAL_HIGH)
+
+#define PIN_CFG_DEFAULT (0)
+
+#define PIN_CFG(num, alt) \
+ (PIN_CFG_DEFAULT |\
+ (PIN_NUM(num) | PIN_##alt))
+
+#define PIN_CFG_INPUT(num, alt, pull) \
+ (PIN_CFG_DEFAULT |\
+ (PIN_NUM(num) | PIN_##alt | PIN_INPUT_##pull))
+
+#define PIN_CFG_OUTPUT(num, alt, val) \
+ (PIN_CFG_DEFAULT |\
+ (PIN_NUM(num) | PIN_##alt | PIN_OUTPUT_##val))
+
+/*
+ * "nmk_gpio" and "NMK_GPIO" stand for "Nomadik GPIO", leaving
+ * the "gpio" namespace for generic and cross-machine functions
+ */
+
+#define GPIO_BLOCK_SHIFT 5
+#define NMK_GPIO_PER_CHIP (1 << GPIO_BLOCK_SHIFT)
+
+/* Register in the logic block */
+#define NMK_GPIO_DAT 0x00
+#define NMK_GPIO_DATS 0x04
+#define NMK_GPIO_DATC 0x08
+#define NMK_GPIO_PDIS 0x0c
+#define NMK_GPIO_DIR 0x10
+#define NMK_GPIO_DIRS 0x14
+#define NMK_GPIO_DIRC 0x18
+#define NMK_GPIO_SLPC 0x1c
+#define NMK_GPIO_AFSLA 0x20
+#define NMK_GPIO_AFSLB 0x24
+#define NMK_GPIO_LOWEMI 0x28
+
+#define NMK_GPIO_RIMSC 0x40
+#define NMK_GPIO_FIMSC 0x44
+#define NMK_GPIO_IS 0x48
+#define NMK_GPIO_IC 0x4c
+#define NMK_GPIO_RWIMSC 0x50
+#define NMK_GPIO_FWIMSC 0x54
+#define NMK_GPIO_WKS 0x58
+/* These appear in DB8540 and later ASICs */
+#define NMK_GPIO_EDGELEVEL 0x5C
+#define NMK_GPIO_LEVEL 0x60
+
+
+/* Pull up/down values */
+enum nmk_gpio_pull {
+ NMK_GPIO_PULL_NONE,
+ NMK_GPIO_PULL_UP,
+ NMK_GPIO_PULL_DOWN,
+};
+
+/* Sleep mode */
+enum nmk_gpio_slpm {
+ NMK_GPIO_SLPM_INPUT,
+ NMK_GPIO_SLPM_WAKEUP_ENABLE = NMK_GPIO_SLPM_INPUT,
+ NMK_GPIO_SLPM_NOCHANGE,
+ NMK_GPIO_SLPM_WAKEUP_DISABLE = NMK_GPIO_SLPM_NOCHANGE,
+};
+
+/*
+ * Platform data to register a block: only the initial gpio/irq number.
+ */
+struct nmk_gpio_platform_data {
+ char *name;
+ int first_gpio;
+ int first_irq;
+ int num_gpio;
+ u32 (*get_secondary_status)(unsigned int bank);
+ void (*set_ioforce)(bool enable);
+ bool supports_sleepmode;
+};
+
struct nmk_gpio_chip {
struct gpio_chip chip;
struct irq_domain *domain;