ARM: dts: bcm2837: Add Raspberry Pi 3 B+
The Raspberry Pi 3 B+ has the following major differences compared
to the model 3 B:
* Microchip LAN7515 (Gigabit Ethernet with integrated USB 2.0 HUB)
* Cypress CYW43455 (802.11n/ac and BT 4.2)
We need to add the USB LAN chip so the bootloader can add the MAC address.
This is necessary because there ain't an EEPROM or a valid OTP.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 7e24249..a300a35 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -75,6 +75,7 @@
bcm2835-rpi-a-plus.dtb \
bcm2836-rpi-2-b.dtb \
bcm2837-rpi-3-b.dtb \
+ bcm2837-rpi-3-b-plus.dtb \
bcm2835-rpi-zero.dtb \
bcm2835-rpi-zero-w.dtb
dtb-$(CONFIG_ARCH_BCM_5301X) += \
diff --git a/arch/arm/boot/dts/bcm2837-rpi-3-b-plus.dts b/arch/arm/boot/dts/bcm2837-rpi-3-b-plus.dts
new file mode 100644
index 0000000..4adb85e
--- /dev/null
+++ b/arch/arm/boot/dts/bcm2837-rpi-3-b-plus.dts
@@ -0,0 +1,108 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+#include "bcm2837.dtsi"
+#include "bcm2835-rpi.dtsi"
+#include "bcm283x-rpi-lan7515.dtsi"
+#include "bcm283x-rpi-usb-host.dtsi"
+
+/ {
+ compatible = "raspberrypi,3-model-b-plus", "brcm,bcm2837";
+ model = "Raspberry Pi 3 Model B+";
+
+ chosen {
+ /* 8250 auxiliary UART instead of pl011 */
+ stdout-path = "serial1:115200n8";
+ };
+
+ memory {
+ reg = <0 0x40000000>;
+ };
+
+ leds {
+ act {
+ gpios = <&gpio 29 GPIO_ACTIVE_HIGH>;
+ };
+
+ pwr {
+ label = "PWR";
+ gpios = <&expgpio 2 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ wifi_pwrseq: wifi-pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ reset-gpios = <&expgpio 1 GPIO_ACTIVE_HIGH>;
+ };
+};
+
+&firmware {
+ expgpio: gpio {
+ compatible = "raspberrypi,firmware-gpio";
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-line-names = "BT_ON",
+ "WL_ON",
+ "STATUS_LED",
+ "LAN_RUN",
+ "",
+ "CAM_GPIO0",
+ "CAM_GPIO1",
+ "";
+ status = "okay";
+ };
+};
+
+&hdmi {
+ hpd-gpios = <&gpio 28 GPIO_ACTIVE_LOW>;
+};
+
+&pwm {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio41>;
+ status = "okay";
+};
+
+/* SDHCI is used to control the SDIO for wireless */
+&sdhci {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&emmc_gpio34>;
+ status = "okay";
+ bus-width = <4>;
+ non-removable;
+ mmc-pwrseq = <&wifi_pwrseq>;
+
+ brcmf: wifi@1 {
+ reg = <1>;
+ compatible = "brcm,bcm4329-fmac";
+ };
+};
+
+/* SDHOST is used to drive the SD card */
+&sdhost {
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdhost_gpio48>;
+ status = "okay";
+ bus-width = <4>;
+};
+
+/* uart0 communicates with the BT module */
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_ctsrts_gpio30 &uart0_gpio32 &gpclk2_gpio43>;
+ status = "okay";
+
+ bluetooth {
+ compatible = "brcm,bcm43438-bt";
+ max-speed = <2000000>;
+ shutdown-gpios = <&expgpio 0 GPIO_ACTIVE_HIGH>;
+ };
+};
+
+/* uart1 is mapped to the pin header */
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_gpio14>;
+ status = "okay";
+};
diff --git a/arch/arm/boot/dts/bcm283x-rpi-lan7515.dtsi b/arch/arm/boot/dts/bcm283x-rpi-lan7515.dtsi
new file mode 100644
index 0000000..9403da0
--- /dev/null
+++ b/arch/arm/boot/dts/bcm283x-rpi-lan7515.dtsi
@@ -0,0 +1,27 @@
+// SPDX-License-Identifier: GPL-2.0
+/ {
+ aliases {
+ ethernet0 = ðernet;
+ };
+};
+
+&usb {
+ usb-port@1 {
+ compatible = "usb424,2514";
+ reg = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ usb-port@1 {
+ compatible = "usb424,2514";
+ reg = <1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethernet: ethernet@1 {
+ compatible = "usb424,7800";
+ reg = <1>;
+ };
+ };
+ };
+};