can: Kconfig: convert 'depends on CAN_DEV' into 'if CAN_DEV...endif' block
This patch adds an 'if CAN_DEV...endif' Block around the CAN driver
symbols in drivers/net/can/Kconfig. So the 'depends on CAN' dependencies
can be removed.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
diff --git a/drivers/net/can/Kconfig b/drivers/net/can/Kconfig
index 8088d8f..0c5a656 100644
--- a/drivers/net/can/Kconfig
+++ b/drivers/net/can/Kconfig
@@ -36,9 +36,10 @@
support. This is the standard library for CAN drivers.
If unsure, say Y.
+if CAN_DEV
+
config CAN_CALC_BITTIMING
bool "CAN bit-timing calculation"
- depends on CAN_DEV
default y
---help---
If enabled, CAN bit-timing parameters will be calculated for the
@@ -52,13 +53,13 @@
config CAN_AT91
tristate "Atmel AT91 onchip CAN controller"
- depends on CAN_DEV && (ARCH_AT91SAM9263 || ARCH_AT91SAM9X5)
+ depends on ARCH_AT91SAM9263 || ARCH_AT91SAM9X5
---help---
This is a driver for the SoC CAN controller in Atmel's AT91SAM9263
and AT91SAM9X5 processors.
config CAN_TI_HECC
- depends on CAN_DEV && ARCH_OMAP3
+ depends on ARCH_OMAP3
tristate "TI High End CAN Controller"
---help---
Driver for TI HECC (High End CAN Controller) module found on many
@@ -66,12 +67,12 @@
config CAN_MCP251X
tristate "Microchip MCP251x SPI CAN controllers"
- depends on CAN_DEV && SPI && HAS_DMA
+ depends on SPI && HAS_DMA
---help---
Driver for the Microchip MCP251x SPI CAN controllers.
config CAN_BFIN
- depends on CAN_DEV && (BF534 || BF536 || BF537 || BF538 || BF539 || BF54x)
+ depends on BF534 || BF536 || BF537 || BF538 || BF539 || BF54x
tristate "Analog Devices Blackfin on-chip CAN"
---help---
Driver for the Analog Devices Blackfin on-chip CAN controllers
@@ -81,7 +82,7 @@
config CAN_JANZ_ICAN3
tristate "Janz VMOD-ICAN3 Intelligent CAN controller"
- depends on CAN_DEV && MFD_JANZ_CMODIO
+ depends on MFD_JANZ_CMODIO
---help---
Driver for Janz VMOD-ICAN3 Intelligent CAN controller module, which
connects to a MODULbus carrier board.
@@ -94,13 +95,13 @@
config CAN_FLEXCAN
tristate "Support for Freescale FLEXCAN based chips"
- depends on CAN_DEV && HAVE_CAN_FLEXCAN
+ depends on HAVE_CAN_FLEXCAN
---help---
Say Y here if you want to support for Freescale FlexCAN.
config PCH_CAN
tristate "Intel EG20T PCH CAN controller"
- depends on CAN_DEV && PCI
+ depends on PCI
---help---
This driver is for PCH CAN of Topcliff (Intel EG20T PCH) which
is an IOH for x86 embedded processor (Intel Atom E6xx series).
@@ -108,7 +109,7 @@
config CAN_GRCAN
tristate "Aeroflex Gaisler GRCAN and GRHCAN CAN devices"
- depends on CAN_DEV && OF
+ depends on OF
---help---
Say Y here if you want to use Aeroflex Gaisler GRCAN or GRHCAN.
Note that the driver supports little endian, even though little
@@ -127,6 +128,8 @@
source "drivers/net/can/softing/Kconfig"
+endif
+
config CAN_DEBUG_DEVICES
bool "CAN devices debugging messages"
---help---