Merge branch 'mvebu/soc3' into next/dt

The dts Makefile has a bunch of nasty conflicts, attempt to resolve
these now to avoid trouble later.

Conflicts:
	arch/arm/boot/dts/Makefile

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 489959d..3d34936 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -55,7 +55,7 @@
 	berlin2cd-google-chromecast.dtb
 dtb-$(CONFIG_ARCH_DAVINCI) += da850-enbw-cmc.dtb \
 	da850-evm.dtb
-dtb-$(CONFIG_ARCH_DOVE) += dove-cm-a510.dtb \
+dtb-$(CONFIG_MACH_DOVE) += dove-cm-a510.dtb \
 	dove-cubox.dtb \
 	dove-d2plug.dtb \
 	dove-d3plug.dtb \
@@ -82,8 +82,8 @@
 	ecx-2000.dtb
 dtb-$(CONFIG_ARCH_INTEGRATOR) += integratorap.dtb \
 	integratorcp.dtb
-dtb-$(CONFIG_ARCH_LPC32XX) += ea3250.dtb phy3250.dtb
-dtb-$(CONFIG_ARCH_KIRKWOOD) += kirkwood-b3.dtb \
+kirkwood := \
+	kirkwood-b3.dtb \
 	kirkwood-cloudbox.dtb \
 	kirkwood-db-88f6281.dtb \
 	kirkwood-db-88f6282.dtb \
@@ -139,6 +139,9 @@
 	kirkwood-ts219-6282.dtb \
 	kirkwood-ts419-6281.dtb \
 	kirkwood-ts419-6282.dtb
+dtb-$(CONFIG_ARCH_KIRKWOOD) += $(kirkwood)
+dtb-$(CONFIG_MACH_KIRKWOOD) += $(kirkwood)
+dtb-$(CONFIG_ARCH_LPC32XX) += ea3250.dtb phy3250.dtb
 dtb-$(CONFIG_ARCH_MARCO) += marco-evb.dtb
 dtb-$(CONFIG_ARCH_MOXART) += moxart-uc7112lx.dtb
 dtb-$(CONFIG_ARCH_MXC) += \
diff --git a/arch/arm/boot/dts/kirkwood-mv88f6281gtw-ge.dts b/arch/arm/boot/dts/kirkwood-mv88f6281gtw-ge.dts
index dc86429..2cb0dc5 100644
--- a/arch/arm/boot/dts/kirkwood-mv88f6281gtw-ge.dts
+++ b/arch/arm/boot/dts/kirkwood-mv88f6281gtw-ge.dts
@@ -122,4 +122,66 @@
 			gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
 		};
 	};
+
+	dsa@0 {
+		compatible = "marvell,dsa";
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		dsa,ethernet = <&eth0>;
+		dsa,mii-bus = <&ethphy0>;
+
+		switch@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0 0>;	/* MDIO address 0, switch 0 in tree */
+
+			port@0 {
+				reg = <0>;
+				label = "lan1";
+			};
+
+			port@1 {
+				reg = <1>;
+				label = "lan2";
+			};
+
+			port@2 {
+				reg = <2>;
+				label = "lan3";
+			};
+
+			port@3 {
+				reg = <3>;
+				label = "lan4";
+			};
+
+			port@4 {
+				reg = <4>;
+				label = "wan";
+			};
+
+			port@5 {
+				reg = <5>;
+				label = "cpu";
+			};
+		};
+	};
+};
+
+&mdio {
+	status = "okay";
+
+	ethphy0: ethernet-phy@ff {
+		reg = <0xff>; 	/* No phy attached */
+		speed = <1000>;
+		duplex = <1>;
+	};
+};
+
+&eth0 {
+	status = "okay";
+	ethernet0-port@0 {
+		phy-handle = <&ethphy0>;
+	};
 };