Merge branch 'upstream' of git://git.linux-mips.org/pub/scm/upstream-linus
* 'upstream' of git://git.linux-mips.org/pub/scm/upstream-linus:
MIPS: Enable ISA_DMA_API config to fix build failure
MIPS: 32-bit: Fix build failure in asm/fcntl.h
MIPS: Remove all generated vmlinuz* files on "make clean"
MIPS: do_sigaltstack() expects userland pointers
MIPS: Fix error values in case of bad_stack
MIPS: Sanitize restart logics
MIPS: secure_computing, syscall audit: syscall number should in r2, not r0.
MIPS: Don't block signals if we'd failed to setup a sigframe
diff --git a/Documentation/networking/e1000.txt b/Documentation/networking/e1000.txt
index 2df7186..d9271e7 100644
--- a/Documentation/networking/e1000.txt
+++ b/Documentation/networking/e1000.txt
@@ -1,82 +1,35 @@
Linux* Base Driver for the Intel(R) PRO/1000 Family of Adapters
===============================================================
-September 26, 2006
-
+Intel Gigabit Linux driver.
+Copyright(c) 1999 - 2010 Intel Corporation.
Contents
========
-- In This Release
- Identifying Your Adapter
-- Building and Installation
- Command Line Parameters
- Speed and Duplex Configuration
- Additional Configurations
-- Known Issues
- Support
-
-In This Release
-===============
-
-This file describes the Linux* Base Driver for the Intel(R) PRO/1000 Family
-of Adapters. This driver includes support for Itanium(R)2-based systems.
-
-For questions related to hardware requirements, refer to the documentation
-supplied with your Intel PRO/1000 adapter. All hardware requirements listed
-apply to use with Linux.
-
-The following features are now available in supported kernels:
- - Native VLANs
- - Channel Bonding (teaming)
- - SNMP
-
-Channel Bonding documentation can be found in the Linux kernel source:
-/Documentation/networking/bonding.txt
-
-The driver information previously displayed in the /proc filesystem is not
-supported in this release. Alternatively, you can use ethtool (version 1.6
-or later), lspci, and ifconfig to obtain the same information.
-
-Instructions on updating ethtool can be found in the section "Additional
-Configurations" later in this document.
-
-NOTE: The Intel(R) 82562v 10/100 Network Connection only provides 10/100
-support.
-
-
Identifying Your Adapter
========================
For more information on how to identify your adapter, go to the Adapter &
Driver ID Guide at:
- http://support.intel.com/support/network/adapter/pro100/21397.htm
+ http://support.intel.com/support/go/network/adapter/idguide.htm
For the latest Intel network drivers for Linux, refer to the following
website. In the search field, enter your adapter name or type, or use the
networking link on the left to search for your adapter:
- http://downloadfinder.intel.com/scripts-df/support_intel.asp
-
+ http://support.intel.com/support/go/network/adapter/home.htm
Command Line Parameters
=======================
-If the driver is built as a module, the following optional parameters
-are used by entering them on the command line with the modprobe command
-using this syntax:
-
- modprobe e1000 [<option>=<VAL1>,<VAL2>,...]
-
-For example, with two PRO/1000 PCI adapters, entering:
-
- modprobe e1000 TxDescriptors=80,128
-
-loads the e1000 driver with 80 TX descriptors for the first adapter and
-128 TX descriptors for the second adapter.
-
The default value for each parameter is generally the recommended setting,
unless otherwise noted.
@@ -89,10 +42,6 @@
parameters, see the application note at:
http://www.intel.com/design/network/applnots/ap450.htm
- A descriptor describes a data buffer and attributes related to
- the data buffer. This information is accessed by the hardware.
-
-
AutoNeg
-------
(Supported only on adapters with copper connections)
@@ -106,7 +55,6 @@
NOTE: Refer to the Speed and Duplex section of this readme for more
information on the AutoNeg parameter.
-
Duplex
------
(Supported only on adapters with copper connections)
@@ -119,7 +67,6 @@
link partner is forced (either full or half), Duplex defaults to half-
duplex.
-
FlowControl
-----------
Valid Range: 0-3 (0=none, 1=Rx only, 2=Tx only, 3=Rx&Tx)
@@ -128,16 +75,16 @@
This parameter controls the automatic generation(Tx) and response(Rx)
to Ethernet PAUSE frames.
-
InterruptThrottleRate
---------------------
(not supported on Intel(R) 82542, 82543 or 82544-based adapters)
-Valid Range: 0,1,3,100-100000 (0=off, 1=dynamic, 3=dynamic conservative)
+Valid Range: 0,1,3,4,100-100000 (0=off, 1=dynamic, 3=dynamic conservative,
+ 4=simplified balancing)
Default Value: 3
The driver can limit the amount of interrupts per second that the adapter
-will generate for incoming packets. It does this by writing a value to the
-adapter that is based on the maximum amount of interrupts that the adapter
+will generate for incoming packets. It does this by writing a value to the
+adapter that is based on the maximum amount of interrupts that the adapter
will generate per second.
Setting InterruptThrottleRate to a value greater or equal to 100
@@ -146,37 +93,43 @@
load on the system and can lower CPU utilization under heavy load,
but will increase latency as packets are not processed as quickly.
-The default behaviour of the driver previously assumed a static
-InterruptThrottleRate value of 8000, providing a good fallback value for
-all traffic types,but lacking in small packet performance and latency.
-The hardware can handle many more small packets per second however, and
+The default behaviour of the driver previously assumed a static
+InterruptThrottleRate value of 8000, providing a good fallback value for
+all traffic types,but lacking in small packet performance and latency.
+The hardware can handle many more small packets per second however, and
for this reason an adaptive interrupt moderation algorithm was implemented.
Since 7.3.x, the driver has two adaptive modes (setting 1 or 3) in which
-it dynamically adjusts the InterruptThrottleRate value based on the traffic
+it dynamically adjusts the InterruptThrottleRate value based on the traffic
that it receives. After determining the type of incoming traffic in the last
-timeframe, it will adjust the InterruptThrottleRate to an appropriate value
+timeframe, it will adjust the InterruptThrottleRate to an appropriate value
for that traffic.
The algorithm classifies the incoming traffic every interval into
-classes. Once the class is determined, the InterruptThrottleRate value is
-adjusted to suit that traffic type the best. There are three classes defined:
+classes. Once the class is determined, the InterruptThrottleRate value is
+adjusted to suit that traffic type the best. There are three classes defined:
"Bulk traffic", for large amounts of packets of normal size; "Low latency",
for small amounts of traffic and/or a significant percentage of small
-packets; and "Lowest latency", for almost completely small packets or
+packets; and "Lowest latency", for almost completely small packets or
minimal traffic.
-In dynamic conservative mode, the InterruptThrottleRate value is set to 4000
-for traffic that falls in class "Bulk traffic". If traffic falls in the "Low
-latency" or "Lowest latency" class, the InterruptThrottleRate is increased
+In dynamic conservative mode, the InterruptThrottleRate value is set to 4000
+for traffic that falls in class "Bulk traffic". If traffic falls in the "Low
+latency" or "Lowest latency" class, the InterruptThrottleRate is increased
stepwise to 20000. This default mode is suitable for most applications.
For situations where low latency is vital such as cluster or
grid computing, the algorithm can reduce latency even more when
InterruptThrottleRate is set to mode 1. In this mode, which operates
-the same as mode 3, the InterruptThrottleRate will be increased stepwise to
+the same as mode 3, the InterruptThrottleRate will be increased stepwise to
70000 for traffic in class "Lowest latency".
+In simplified mode the interrupt rate is based on the ratio of Tx and
+Rx traffic. If the bytes per second rate is approximately equal, the
+interrupt rate will drop as low as 2000 interrupts per second. If the
+traffic is mostly transmit or mostly receive, the interrupt rate could
+be as high as 8000.
+
Setting InterruptThrottleRate to 0 turns off any interrupt moderation
and may improve small packet latency, but is generally not suitable
for bulk throughput traffic.
@@ -212,8 +165,6 @@
be platform-specific. If CPU utilization is not a concern, use
RX_POLLING (NAPI) and default driver settings.
-
-
RxDescriptors
-------------
Valid Range: 80-256 for 82542 and 82543-based adapters
@@ -225,15 +176,14 @@
incoming packets, at the expense of increased system memory utilization.
Each descriptor is 16 bytes. A receive buffer is also allocated for each
-descriptor and can be either 2048, 4096, 8192, or 16384 bytes, depending
+descriptor and can be either 2048, 4096, 8192, or 16384 bytes, depending
on the MTU setting. The maximum MTU size is 16110.
-NOTE: MTU designates the frame size. It only needs to be set for Jumbo
- Frames. Depending on the available system resources, the request
- for a higher number of receive descriptors may be denied. In this
+NOTE: MTU designates the frame size. It only needs to be set for Jumbo
+ Frames. Depending on the available system resources, the request
+ for a higher number of receive descriptors may be denied. In this
case, use a lower number.
-
RxIntDelay
----------
Valid Range: 0-65535 (0=off)
@@ -254,7 +204,6 @@
restoring the network connection. To eliminate the potential
for the hang ensure that RxIntDelay is set to 0.
-
RxAbsIntDelay
-------------
(This parameter is supported only on 82540, 82545 and later adapters.)
@@ -268,7 +217,6 @@
along with RxIntDelay, may improve traffic throughput in specific network
conditions.
-
Speed
-----
(This parameter is supported only on adapters with copper connections.)
@@ -280,7 +228,6 @@
partner is set to auto-negotiate, the board will auto-detect the correct
speed. Duplex should also be set when Speed is set to either 10 or 100.
-
TxDescriptors
-------------
Valid Range: 80-256 for 82542 and 82543-based adapters
@@ -295,6 +242,36 @@
higher number of transmit descriptors may be denied. In this case,
use a lower number.
+TxDescriptorStep
+----------------
+Valid Range: 1 (use every Tx Descriptor)
+ 4 (use every 4th Tx Descriptor)
+
+Default Value: 1 (use every Tx Descriptor)
+
+On certain non-Intel architectures, it has been observed that intense TX
+traffic bursts of short packets may result in an improper descriptor
+writeback. If this occurs, the driver will report a "TX Timeout" and reset
+the adapter, after which the transmit flow will restart, though data may
+have stalled for as much as 10 seconds before it resumes.
+
+The improper writeback does not occur on the first descriptor in a system
+memory cache-line, which is typically 32 bytes, or 4 descriptors long.
+
+Setting TxDescriptorStep to a value of 4 will ensure that all TX descriptors
+are aligned to the start of a system memory cache line, and so this problem
+will not occur.
+
+NOTES: Setting TxDescriptorStep to 4 effectively reduces the number of
+ TxDescriptors available for transmits to 1/4 of the normal allocation.
+ This has a possible negative performance impact, which may be
+ compensated for by allocating more descriptors using the TxDescriptors
+ module parameter.
+
+ There are other conditions which may result in "TX Timeout", which will
+ not be resolved by the use of the TxDescriptorStep parameter. As the
+ issue addressed by this parameter has never been observed on Intel
+ Architecture platforms, it should not be used on Intel platforms.
TxIntDelay
----------
@@ -307,7 +284,6 @@
system is reporting dropped transmits, this value may be set too high
causing the driver to run out of available transmit descriptors.
-
TxAbsIntDelay
-------------
(This parameter is supported only on 82540, 82545 and later adapters.)
@@ -330,6 +306,35 @@
A value of '1' indicates that the driver should enable IP checksum
offload for received packets (both UDP and TCP) to the adapter hardware.
+Copybreak
+---------
+Valid Range: 0-xxxxxxx (0=off)
+Default Value: 256
+Usage: insmod e1000.ko copybreak=128
+
+Driver copies all packets below or equaling this size to a fresh Rx
+buffer before handing it up the stack.
+
+This parameter is different than other parameters, in that it is a
+single (not 1,1,1 etc.) parameter applied to all driver instances and
+it is also available during runtime at
+/sys/module/e1000/parameters/copybreak
+
+SmartPowerDownEnable
+--------------------
+Valid Range: 0-1
+Default Value: 0 (disabled)
+
+Allows PHY to turn off in lower power states. The user can turn off
+this parameter in supported chipsets.
+
+KumeranLockLoss
+---------------
+Valid Range: 0-1
+Default Value: 1 (enabled)
+
+This workaround skips resetting the PHY at shutdown for the initial
+silicon releases of ICH8 systems.
Speed and Duplex Configuration
==============================
@@ -385,40 +390,9 @@
parameter should not be used. Instead, use the Speed and Duplex parameters
previously mentioned to force the adapter to the same speed and duplex.
-
Additional Configurations
=========================
- Configuring the Driver on Different Distributions
- -------------------------------------------------
- Configuring a network driver to load properly when the system is started
- is distribution dependent. Typically, the configuration process involves
- adding an alias line to /etc/modules.conf or /etc/modprobe.conf as well
- as editing other system startup scripts and/or configuration files. Many
- popular Linux distributions ship with tools to make these changes for you.
- To learn the proper way to configure a network device for your system,
- refer to your distribution documentation. If during this process you are
- asked for the driver or module name, the name for the Linux Base Driver
- for the Intel(R) PRO/1000 Family of Adapters is e1000.
-
- As an example, if you install the e1000 driver for two PRO/1000 adapters
- (eth0 and eth1) and set the speed and duplex to 10full and 100half, add
- the following to modules.conf or or modprobe.conf:
-
- alias eth0 e1000
- alias eth1 e1000
- options e1000 Speed=10,100 Duplex=2,1
-
- Viewing Link Messages
- ---------------------
- Link messages will not be displayed to the console if the distribution is
- restricting system messages. In order to see network driver link messages
- on your console, set dmesg to eight by entering the following:
-
- dmesg -n 8
-
- NOTE: This setting is not saved across reboots.
-
Jumbo Frames
------------
Jumbo Frames support is enabled by changing the MTU to a value larger than
@@ -437,9 +411,11 @@
setting in a different location.
Notes:
-
- - To enable Jumbo Frames, increase the MTU size on the interface beyond
- 1500.
+ Degradation in throughput performance may be observed in some Jumbo frames
+ environments. If this is observed, increasing the application's socket buffer
+ size and/or increasing the /proc/sys/net/ipv4/tcp_*mem entry values may help.
+ See the specific application manual and /usr/src/linux*/Documentation/
+ networking/ip-sysctl.txt for more details.
- The maximum MTU setting for Jumbo Frames is 16110. This value coincides
with the maximum Jumbo Frames size of 16128.
@@ -447,40 +423,11 @@
- Using Jumbo Frames at 10 or 100 Mbps may result in poor performance or
loss of link.
- - Some Intel gigabit adapters that support Jumbo Frames have a frame size
- limit of 9238 bytes, with a corresponding MTU size limit of 9216 bytes.
- The adapters with this limitation are based on the Intel(R) 82571EB,
- 82572EI, 82573L and 80003ES2LAN controller. These correspond to the
- following product names:
- Intel(R) PRO/1000 PT Server Adapter
- Intel(R) PRO/1000 PT Desktop Adapter
- Intel(R) PRO/1000 PT Network Connection
- Intel(R) PRO/1000 PT Dual Port Server Adapter
- Intel(R) PRO/1000 PT Dual Port Network Connection
- Intel(R) PRO/1000 PF Server Adapter
- Intel(R) PRO/1000 PF Network Connection
- Intel(R) PRO/1000 PF Dual Port Server Adapter
- Intel(R) PRO/1000 PB Server Connection
- Intel(R) PRO/1000 PL Network Connection
- Intel(R) PRO/1000 EB Network Connection with I/O Acceleration
- Intel(R) PRO/1000 EB Backplane Connection with I/O Acceleration
- Intel(R) PRO/1000 PT Quad Port Server Adapter
-
- Adapters based on the Intel(R) 82542 and 82573V/E controller do not
support Jumbo Frames. These correspond to the following product names:
Intel(R) PRO/1000 Gigabit Server Adapter
Intel(R) PRO/1000 PM Network Connection
- - The following adapters do not support Jumbo Frames:
- Intel(R) 82562V 10/100 Network Connection
- Intel(R) 82566DM Gigabit Network Connection
- Intel(R) 82566DC Gigabit Network Connection
- Intel(R) 82566MM Gigabit Network Connection
- Intel(R) 82566MC Gigabit Network Connection
- Intel(R) 82562GT 10/100 Network Connection
- Intel(R) 82562G 10/100 Network Connection
-
-
Ethtool
-------
The driver utilizes the ethtool interface for driver configuration and
@@ -490,142 +437,14 @@
The latest release of ethtool can be found from
http://sourceforge.net/projects/gkernel.
- NOTE: Ethtool 1.6 only supports a limited set of ethtool options. Support
- for a more complete ethtool feature set can be enabled by upgrading
- ethtool to ethtool-1.8.1.
-
Enabling Wake on LAN* (WoL)
---------------------------
- WoL is configured through the Ethtool* utility. Ethtool is included with
- all versions of Red Hat after Red Hat 7.2. For other Linux distributions,
- download and install Ethtool from the following website:
- http://sourceforge.net/projects/gkernel.
-
- For instructions on enabling WoL with Ethtool, refer to the website listed
- above.
+ WoL is configured through the Ethtool* utility.
WoL will be enabled on the system during the next shut down or reboot.
For this driver version, in order to enable WoL, the e1000 driver must be
loaded when shutting down or rebooting the system.
- Wake On LAN is only supported on port A for the following devices:
- Intel(R) PRO/1000 PT Dual Port Network Connection
- Intel(R) PRO/1000 PT Dual Port Server Connection
- Intel(R) PRO/1000 PT Dual Port Server Adapter
- Intel(R) PRO/1000 PF Dual Port Server Adapter
- Intel(R) PRO/1000 PT Quad Port Server Adapter
-
- NAPI
- ----
- NAPI (Rx polling mode) is enabled in the e1000 driver.
-
- See www.cyberus.ca/~hadi/usenix-paper.tgz for more information on NAPI.
-
-
-Known Issues
-============
-
-Dropped Receive Packets on Half-duplex 10/100 Networks
-------------------------------------------------------
-If you have an Intel PCI Express adapter running at 10mbps or 100mbps, half-
-duplex, you may observe occasional dropped receive packets. There are no
-workarounds for this problem in this network configuration. The network must
-be updated to operate in full-duplex, and/or 1000mbps only.
-
-Jumbo Frames System Requirement
--------------------------------
-Memory allocation failures have been observed on Linux systems with 64 MB
-of RAM or less that are running Jumbo Frames. If you are using Jumbo
-Frames, your system may require more than the advertised minimum
-requirement of 64 MB of system memory.
-
-Performance Degradation with Jumbo Frames
------------------------------------------
-Degradation in throughput performance may be observed in some Jumbo frames
-environments. If this is observed, increasing the application's socket
-buffer size and/or increasing the /proc/sys/net/ipv4/tcp_*mem entry values
-may help. See the specific application manual and
-/usr/src/linux*/Documentation/
-networking/ip-sysctl.txt for more details.
-
-Jumbo Frames on Foundry BigIron 8000 switch
--------------------------------------------
-There is a known issue using Jumbo frames when connected to a Foundry
-BigIron 8000 switch. This is a 3rd party limitation. If you experience
-loss of packets, lower the MTU size.
-
-Allocating Rx Buffers when Using Jumbo Frames
----------------------------------------------
-Allocating Rx buffers when using Jumbo Frames on 2.6.x kernels may fail if
-the available memory is heavily fragmented. This issue may be seen with PCI-X
-adapters or with packet split disabled. This can be reduced or eliminated
-by changing the amount of available memory for receive buffer allocation, by
-increasing /proc/sys/vm/min_free_kbytes.
-
-Multiple Interfaces on Same Ethernet Broadcast Network
-------------------------------------------------------
-Due to the default ARP behavior on Linux, it is not possible to have
-one system on two IP networks in the same Ethernet broadcast domain
-(non-partitioned switch) behave as expected. All Ethernet interfaces
-will respond to IP traffic for any IP address assigned to the system.
-This results in unbalanced receive traffic.
-
-If you have multiple interfaces in a server, either turn on ARP
-filtering by entering:
-
- echo 1 > /proc/sys/net/ipv4/conf/all/arp_filter
-(this only works if your kernel's version is higher than 2.4.5),
-
-NOTE: This setting is not saved across reboots. The configuration
-change can be made permanent by adding the line:
- net.ipv4.conf.all.arp_filter = 1
-to the file /etc/sysctl.conf
-
- or,
-
-install the interfaces in separate broadcast domains (either in
-different switches or in a switch partitioned to VLANs).
-
-82541/82547 can't link or are slow to link with some link partners
------------------------------------------------------------------
-There is a known compatibility issue with 82541/82547 and some
-low-end switches where the link will not be established, or will
-be slow to establish. In particular, these switches are known to
-be incompatible with 82541/82547:
-
- Planex FXG-08TE
- I-O Data ETG-SH8
-
-To workaround this issue, the driver can be compiled with an override
-of the PHY's master/slave setting. Forcing master or forcing slave
-mode will improve time-to-link.
-
- # make CFLAGS_EXTRA=-DE1000_MASTER_SLAVE=<n>
-
-Where <n> is:
-
- 0 = Hardware default
- 1 = Master mode
- 2 = Slave mode
- 3 = Auto master/slave
-
-Disable rx flow control with ethtool
-------------------------------------
-In order to disable receive flow control using ethtool, you must turn
-off auto-negotiation on the same command line.
-
-For example:
-
- ethtool -A eth? autoneg off rx off
-
-Unplugging network cable while ethtool -p is running
-----------------------------------------------------
-In kernel versions 2.5.50 and later (including 2.6 kernel), unplugging
-the network cable while ethtool -p is running will cause the system to
-become unresponsive to keyboard commands, except for control-alt-delete.
-Restarting the system appears to be the only remedy.
-
-
Support
=======
diff --git a/Documentation/networking/e1000e.txt b/Documentation/networking/e1000e.txt
new file mode 100644
index 0000000..6aa048ba
--- /dev/null
+++ b/Documentation/networking/e1000e.txt
@@ -0,0 +1,302 @@
+Linux* Driver for Intel(R) Network Connection
+===============================================================
+
+Intel Gigabit Linux driver.
+Copyright(c) 1999 - 2010 Intel Corporation.
+
+Contents
+========
+
+- Identifying Your Adapter
+- Command Line Parameters
+- Additional Configurations
+- Support
+
+Identifying Your Adapter
+========================
+
+The e1000e driver supports all PCI Express Intel(R) Gigabit Network
+Connections, except those that are 82575, 82576 and 82580-based*.
+
+* NOTE: The Intel(R) PRO/1000 P Dual Port Server Adapter is supported by
+ the e1000 driver, not the e1000e driver due to the 82546 part being used
+ behind a PCI Express bridge.
+
+For more information on how to identify your adapter, go to the Adapter &
+Driver ID Guide at:
+
+ http://support.intel.com/support/go/network/adapter/idguide.htm
+
+For the latest Intel network drivers for Linux, refer to the following
+website. In the search field, enter your adapter name or type, or use the
+networking link on the left to search for your adapter:
+
+ http://support.intel.com/support/go/network/adapter/home.htm
+
+Command Line Parameters
+=======================
+
+The default value for each parameter is generally the recommended setting,
+unless otherwise noted.
+
+NOTES: For more information about the InterruptThrottleRate,
+ RxIntDelay, TxIntDelay, RxAbsIntDelay, and TxAbsIntDelay
+ parameters, see the application note at:
+ http://www.intel.com/design/network/applnots/ap450.htm
+
+InterruptThrottleRate
+---------------------
+Valid Range: 0,1,3,4,100-100000 (0=off, 1=dynamic, 3=dynamic conservative,
+ 4=simplified balancing)
+Default Value: 3
+
+The driver can limit the amount of interrupts per second that the adapter
+will generate for incoming packets. It does this by writing a value to the
+adapter that is based on the maximum amount of interrupts that the adapter
+will generate per second.
+
+Setting InterruptThrottleRate to a value greater or equal to 100
+will program the adapter to send out a maximum of that many interrupts
+per second, even if more packets have come in. This reduces interrupt
+load on the system and can lower CPU utilization under heavy load,
+but will increase latency as packets are not processed as quickly.
+
+The driver has two adaptive modes (setting 1 or 3) in which
+it dynamically adjusts the InterruptThrottleRate value based on the traffic
+that it receives. After determining the type of incoming traffic in the last
+timeframe, it will adjust the InterruptThrottleRate to an appropriate value
+for that traffic.
+
+The algorithm classifies the incoming traffic every interval into
+classes. Once the class is determined, the InterruptThrottleRate value is
+adjusted to suit that traffic type the best. There are three classes defined:
+"Bulk traffic", for large amounts of packets of normal size; "Low latency",
+for small amounts of traffic and/or a significant percentage of small
+packets; and "Lowest latency", for almost completely small packets or
+minimal traffic.
+
+In dynamic conservative mode, the InterruptThrottleRate value is set to 4000
+for traffic that falls in class "Bulk traffic". If traffic falls in the "Low
+latency" or "Lowest latency" class, the InterruptThrottleRate is increased
+stepwise to 20000. This default mode is suitable for most applications.
+
+For situations where low latency is vital such as cluster or
+grid computing, the algorithm can reduce latency even more when
+InterruptThrottleRate is set to mode 1. In this mode, which operates
+the same as mode 3, the InterruptThrottleRate will be increased stepwise to
+70000 for traffic in class "Lowest latency".
+
+In simplified mode the interrupt rate is based on the ratio of Tx and
+Rx traffic. If the bytes per second rate is approximately equal the
+interrupt rate will drop as low as 2000 interrupts per second. If the
+traffic is mostly transmit or mostly receive, the interrupt rate could
+be as high as 8000.
+
+Setting InterruptThrottleRate to 0 turns off any interrupt moderation
+and may improve small packet latency, but is generally not suitable
+for bulk throughput traffic.
+
+NOTE: InterruptThrottleRate takes precedence over the TxAbsIntDelay and
+ RxAbsIntDelay parameters. In other words, minimizing the receive
+ and/or transmit absolute delays does not force the controller to
+ generate more interrupts than what the Interrupt Throttle Rate
+ allows.
+
+NOTE: When e1000e is loaded with default settings and multiple adapters
+ are in use simultaneously, the CPU utilization may increase non-
+ linearly. In order to limit the CPU utilization without impacting
+ the overall throughput, we recommend that you load the driver as
+ follows:
+
+ modprobe e1000e InterruptThrottleRate=3000,3000,3000
+
+ This sets the InterruptThrottleRate to 3000 interrupts/sec for
+ the first, second, and third instances of the driver. The range
+ of 2000 to 3000 interrupts per second works on a majority of
+ systems and is a good starting point, but the optimal value will
+ be platform-specific. If CPU utilization is not a concern, use
+ RX_POLLING (NAPI) and default driver settings.
+
+RxIntDelay
+----------
+Valid Range: 0-65535 (0=off)
+Default Value: 0
+
+This value delays the generation of receive interrupts in units of 1.024
+microseconds. Receive interrupt reduction can improve CPU efficiency if
+properly tuned for specific network traffic. Increasing this value adds
+extra latency to frame reception and can end up decreasing the throughput
+of TCP traffic. If the system is reporting dropped receives, this value
+may be set too high, causing the driver to run out of available receive
+descriptors.
+
+CAUTION: When setting RxIntDelay to a value other than 0, adapters may
+ hang (stop transmitting) under certain network conditions. If
+ this occurs a NETDEV WATCHDOG message is logged in the system
+ event log. In addition, the controller is automatically reset,
+ restoring the network connection. To eliminate the potential
+ for the hang ensure that RxIntDelay is set to 0.
+
+RxAbsIntDelay
+-------------
+Valid Range: 0-65535 (0=off)
+Default Value: 8
+
+This value, in units of 1.024 microseconds, limits the delay in which a
+receive interrupt is generated. Useful only if RxIntDelay is non-zero,
+this value ensures that an interrupt is generated after the initial
+packet is received within the set amount of time. Proper tuning,
+along with RxIntDelay, may improve traffic throughput in specific network
+conditions.
+
+TxIntDelay
+----------
+Valid Range: 0-65535 (0=off)
+Default Value: 8
+
+This value delays the generation of transmit interrupts in units of
+1.024 microseconds. Transmit interrupt reduction can improve CPU
+efficiency if properly tuned for specific network traffic. If the
+system is reporting dropped transmits, this value may be set too high
+causing the driver to run out of available transmit descriptors.
+
+TxAbsIntDelay
+-------------
+Valid Range: 0-65535 (0=off)
+Default Value: 32
+
+This value, in units of 1.024 microseconds, limits the delay in which a
+transmit interrupt is generated. Useful only if TxIntDelay is non-zero,
+this value ensures that an interrupt is generated after the initial
+packet is sent on the wire within the set amount of time. Proper tuning,
+along with TxIntDelay, may improve traffic throughput in specific
+network conditions.
+
+Copybreak
+---------
+Valid Range: 0-xxxxxxx (0=off)
+Default Value: 256
+
+Driver copies all packets below or equaling this size to a fresh Rx
+buffer before handing it up the stack.
+
+This parameter is different than other parameters, in that it is a
+single (not 1,1,1 etc.) parameter applied to all driver instances and
+it is also available during runtime at
+/sys/module/e1000e/parameters/copybreak
+
+SmartPowerDownEnable
+--------------------
+Valid Range: 0-1
+Default Value: 0 (disabled)
+
+Allows PHY to turn off in lower power states. The user can set this parameter
+in supported chipsets.
+
+KumeranLockLoss
+---------------
+Valid Range: 0-1
+Default Value: 1 (enabled)
+
+This workaround skips resetting the PHY at shutdown for the initial
+silicon releases of ICH8 systems.
+
+IntMode
+-------
+Valid Range: 0-2 (0=legacy, 1=MSI, 2=MSI-X)
+Default Value: 2
+
+Allows changing the interrupt mode at module load time, without requiring a
+recompile. If the driver load fails to enable a specific interrupt mode, the
+driver will try other interrupt modes, from least to most compatible. The
+interrupt order is MSI-X, MSI, Legacy. If specifying MSI (IntMode=1)
+interrupts, only MSI and Legacy will be attempted.
+
+CrcStripping
+------------
+Valid Range: 0-1
+Default Value: 1 (enabled)
+
+Strip the CRC from received packets before sending up the network stack. If
+you have a machine with a BMC enabled but cannot receive IPMI traffic after
+loading or enabling the driver, try disabling this feature.
+
+WriteProtectNVM
+---------------
+Valid Range: 0-1
+Default Value: 1 (enabled)
+
+Set the hardware to ignore all write/erase cycles to the GbE region in the
+ICHx NVM (non-volatile memory). This feature can be disabled by the
+WriteProtectNVM module parameter (enabled by default) only after a hardware
+reset, but the machine must be power cycled before trying to enable writes.
+
+Note: the kernel boot option iomem=relaxed may need to be set if the kernel
+config option CONFIG_STRICT_DEVMEM=y, if the root user wants to write the
+NVM from user space via ethtool.
+
+Additional Configurations
+=========================
+
+ Jumbo Frames
+ ------------
+ Jumbo Frames support is enabled by changing the MTU to a value larger than
+ the default of 1500. Use the ifconfig command to increase the MTU size.
+ For example:
+
+ ifconfig eth<x> mtu 9000 up
+
+ This setting is not saved across reboots.
+
+ Notes:
+
+ - The maximum MTU setting for Jumbo Frames is 9216. This value coincides
+ with the maximum Jumbo Frames size of 9234 bytes.
+
+ - Using Jumbo Frames at 10 or 100 Mbps is not supported and may result in
+ poor performance or loss of link.
+
+ - Some adapters limit Jumbo Frames sized packets to a maximum of
+ 4096 bytes and some adapters do not support Jumbo Frames.
+
+
+ Ethtool
+ -------
+ The driver utilizes the ethtool interface for driver configuration and
+ diagnostics, as well as displaying statistical information. We
+ strongly recommend downloading the latest version of Ethtool at:
+
+ http://sourceforge.net/projects/gkernel.
+
+ Speed and Duplex
+ ----------------
+ Speed and Duplex are configured through the Ethtool* utility. For
+ instructions, refer to the Ethtool man page.
+
+ Enabling Wake on LAN* (WoL)
+ ---------------------------
+ WoL is configured through the Ethtool* utility. For instructions on
+ enabling WoL with Ethtool, refer to the Ethtool man page.
+
+ WoL will be enabled on the system during the next shut down or reboot.
+ For this driver version, in order to enable WoL, the e1000e driver must be
+ loaded when shutting down or rebooting the system.
+
+ In most cases Wake On LAN is only supported on port A for multiple port
+ adapters. To verify if a port supports Wake on LAN run ethtool eth<X>.
+
+
+Support
+=======
+
+For general information, go to the Intel support website at:
+
+ www.intel.com/support/
+
+or the Intel Wired Networking project hosted by Sourceforge at:
+
+ http://sourceforge.net/projects/e1000
+
+If an issue is identified with the released source code on the supported
+kernel with a supported adapter, email the specific information related
+to the issue to e1000-devel@lists.sf.net
diff --git a/Documentation/networking/ixgbevf.txt b/Documentation/networking/ixgbevf.txt
old mode 100755
new mode 100644
index 19015de..21dd5d1
--- a/Documentation/networking/ixgbevf.txt
+++ b/Documentation/networking/ixgbevf.txt
@@ -1,19 +1,16 @@
Linux* Base Driver for Intel(R) Network Connection
==================================================
-November 24, 2009
+Intel Gigabit Linux driver.
+Copyright(c) 1999 - 2010 Intel Corporation.
Contents
========
-- In This Release
- Identifying Your Adapter
- Known Issues/Troubleshooting
- Support
-In This Release
-===============
-
This file describes the ixgbevf Linux* Base Driver for Intel Network
Connection.
@@ -33,7 +30,7 @@
For more information on how to identify your adapter, go to the Adapter &
Driver ID Guide at:
- http://support.intel.com/support/network/sb/CS-008441.htm
+ http://support.intel.com/support/go/network/adapter/idguide.htm
Known Issues/Troubleshooting
============================
@@ -57,34 +54,3 @@
If an issue is identified with the released source code on the supported
kernel with a supported adapter, email the specific information related
to the issue to e1000-devel@lists.sf.net
-
-License
-=======
-
-Intel 10 Gigabit Linux driver.
-Copyright(c) 1999 - 2009 Intel Corporation.
-
-This program is free software; you can redistribute it and/or modify it
-under the terms and conditions of the GNU General Public License,
-version 2, as published by the Free Software Foundation.
-
-This program is distributed in the hope it will be useful, but WITHOUT
-ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
-FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
-more details.
-
-You should have received a copy of the GNU General Public License along with
-this program; if not, write to the Free Software Foundation, Inc.,
-51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
-
-The full GNU General Public License is included in this distribution in
-the file called "COPYING".
-
-Trademarks
-==========
-
-Intel, Itanium, and Pentium are trademarks or registered trademarks of
-Intel Corporation or its subsidiaries in the United States and other
-countries.
-
-* Other names and brands may be claimed as the property of others.
diff --git a/Documentation/vm/page-types.c b/Documentation/vm/page-types.c
index ccd951f..cc96ee2 100644
--- a/Documentation/vm/page-types.c
+++ b/Documentation/vm/page-types.c
@@ -478,7 +478,7 @@
}
if (opt_unpoison && !hwpoison_forget_fd) {
- sprintf(buf, "%s/renew-pfn", hwpoison_debug_fs);
+ sprintf(buf, "%s/unpoison-pfn", hwpoison_debug_fs);
hwpoison_forget_fd = checked_open(buf, O_WRONLY);
}
}
diff --git a/MAINTAINERS b/MAINTAINERS
index f46d8e6..7679bf3 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -969,6 +969,16 @@
S: Maintained
F: arch/arm/mach-s5p*/
+ARM/SAMSUNG S5P SERIES FIMC SUPPORT
+M: Kyungmin Park <kyungmin.park@samsung.com>
+M: Sylwester Nawrocki <s.nawrocki@samsung.com>
+L: linux-arm-kernel@lists.infradead.org
+L: linux-media@vger.kernel.org
+S: Maintained
+F: arch/arm/plat-s5p/dev-fimc*
+F: arch/arm/plat-samsung/include/plat/*fimc*
+F: drivers/media/video/s5p-fimc/
+
ARM/SHMOBILE ARM ARCHITECTURE
M: Paul Mundt <lethal@linux-sh.org>
M: Magnus Damm <magnus.damm@gmail.com>
@@ -2535,7 +2545,7 @@
F: drivers/scsi/gdt*
GENERIC GPIO I2C DRIVER
-M: Haavard Skinnemoen <hskinnemoen@atmel.com>
+M: Haavard Skinnemoen <hskinnemoen@gmail.com>
S: Supported
F: drivers/i2c/busses/i2c-gpio.c
F: include/linux/i2c-gpio.h
@@ -3063,16 +3073,27 @@
S: Maintained
F: drivers/net/ixp2000/
-INTEL ETHERNET DRIVERS (e100/e1000/e1000e/igb/igbvf/ixgb/ixgbe)
+INTEL ETHERNET DRIVERS (e100/e1000/e1000e/igb/igbvf/ixgb/ixgbe/ixgbevf)
M: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
M: Jesse Brandeburg <jesse.brandeburg@intel.com>
M: Bruce Allan <bruce.w.allan@intel.com>
-M: Alex Duyck <alexander.h.duyck@intel.com>
+M: Carolyn Wyborny <carolyn.wyborny@intel.com>
+M: Don Skidmore <donald.c.skidmore@intel.com>
+M: Greg Rose <gregory.v.rose@intel.com>
M: PJ Waskiewicz <peter.p.waskiewicz.jr@intel.com>
+M: Alex Duyck <alexander.h.duyck@intel.com>
M: John Ronciak <john.ronciak@intel.com>
L: e1000-devel@lists.sourceforge.net
W: http://e1000.sourceforge.net/
S: Supported
+F: Documentation/networking/e100.txt
+F: Documentation/networking/e1000.txt
+F: Documentation/networking/e1000e.txt
+F: Documentation/networking/igb.txt
+F: Documentation/networking/igbvf.txt
+F: Documentation/networking/ixgb.txt
+F: Documentation/networking/ixgbe.txt
+F: Documentation/networking/ixgbevf.txt
F: drivers/net/e100.c
F: drivers/net/e1000/
F: drivers/net/e1000e/
@@ -3080,6 +3101,7 @@
F: drivers/net/igbvf/
F: drivers/net/ixgb/
F: drivers/net/ixgbe/
+F: drivers/net/ixgbevf/
INTEL PRO/WIRELESS 2100 NETWORK CONNECTION SUPPORT
L: linux-wireless@vger.kernel.org
@@ -5008,6 +5030,12 @@
F: drivers/media/video/*7146*
F: include/media/*7146*
+SAMSUNG AUDIO (ASoC) DRIVERS
+M: Jassi Brar <jassi.brar@samsung.com>
+L: alsa-devel@alsa-project.org (moderated for non-subscribers)
+S: Supported
+F: sound/soc/s3c24xx
+
TLG2300 VIDEO4LINUX-2 DRIVER
M: Huang Shijie <shijie8@gmail.com>
M: Kang Yong <kangyong@telegent.com>
@@ -6450,8 +6478,10 @@
WOLFSON MICROELECTRONICS DRIVERS
M: Mark Brown <broonie@opensource.wolfsonmicro.com>
M: Ian Lartey <ian@opensource.wolfsonmicro.com>
+M: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
+T: git git://opensource.wolfsonmicro.com/linux-2.6-asoc
T: git git://opensource.wolfsonmicro.com/linux-2.6-audioplus
-W: http://opensource.wolfsonmicro.com/node/8
+W: http://opensource.wolfsonmicro.com/content/linux-drivers-wolfson-devices
S: Supported
F: Documentation/hwmon/wm83??
F: drivers/leds/leds-wm83*.c
diff --git a/Makefile b/Makefile
index 471c49f..7583116 100644
--- a/Makefile
+++ b/Makefile
@@ -1,8 +1,8 @@
VERSION = 2
PATCHLEVEL = 6
SUBLEVEL = 36
-EXTRAVERSION = -rc6
-NAME = Sheep on Meth
+EXTRAVERSION = -rc8
+NAME = Flesh-Eating Bats with Fangs
# *DOCUMENTATION*
# To see a list of typical targets execute "make help"
diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index 88c97bc..9c26ba7 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -1101,6 +1101,20 @@
invalidated are not, resulting in an incoherency in the system page
tables. The workaround changes the TLB flushing routines to invalidate
entries regardless of the ASID.
+
+config ARM_ERRATA_743622
+ bool "ARM errata: Faulty hazard checking in the Store Buffer may lead to data corruption"
+ depends on CPU_V7
+ help
+ This option enables the workaround for the 743622 Cortex-A9
+ (r2p0..r2p2) erratum. Under very rare conditions, a faulty
+ optimisation in the Cortex-A9 Store Buffer may lead to data
+ corruption. This workaround sets a specific bit in the diagnostic
+ register of the Cortex-A9 which disables the Store Buffer
+ optimisation, preventing the defect from occurring. This has no
+ visible impact on the overall performance or power consumption of the
+ processor.
+
endmenu
source "arch/arm/common/Kconfig"
diff --git a/arch/arm/kernel/kprobes-decode.c b/arch/arm/kernel/kprobes-decode.c
index 8bccbfa..2c1f005 100644
--- a/arch/arm/kernel/kprobes-decode.c
+++ b/arch/arm/kernel/kprobes-decode.c
@@ -1162,11 +1162,12 @@
{
/*
* MSR : cccc 0011 0x10 xxxx xxxx xxxx xxxx xxxx
- * Undef : cccc 0011 0x00 xxxx xxxx xxxx xxxx xxxx
+ * Undef : cccc 0011 0100 xxxx xxxx xxxx xxxx xxxx
* ALU op with S bit and Rd == 15 :
* cccc 001x xxx1 xxxx 1111 xxxx xxxx xxxx
*/
- if ((insn & 0x0f900000) == 0x03200000 || /* MSR & Undef */
+ if ((insn & 0x0fb00000) == 0x03200000 || /* MSR */
+ (insn & 0x0ff00000) == 0x03400000 || /* Undef */
(insn & 0x0e10f000) == 0x0210f000) /* ALU s-bit, R15 */
return INSN_REJECTED;
@@ -1177,7 +1178,7 @@
* *S (bit 20) updates condition codes
* ADC/SBC/RSC reads the C flag
*/
- insn &= 0xfff00fff; /* Rn = r0, Rd = r0 */
+ insn &= 0xffff0fff; /* Rd = r0 */
asi->insn[0] = insn;
asi->insn_handler = (insn & (1 << 20)) ? /* S-bit */
emulate_alu_imm_rwflags : emulate_alu_imm_rflags;
diff --git a/arch/arm/mach-at91/include/mach/system.h b/arch/arm/mach-at91/include/mach/system.h
index c80e090..ee8db15 100644
--- a/arch/arm/mach-at91/include/mach/system.h
+++ b/arch/arm/mach-at91/include/mach/system.h
@@ -28,17 +28,16 @@
static inline void arch_idle(void)
{
-#ifndef CONFIG_DEBUG_KERNEL
/*
* Disable the processor clock. The processor will be automatically
* re-enabled by an interrupt or by a reset.
*/
at91_sys_write(AT91_PMC_SCDR, AT91_PMC_PCK);
-#else
+#ifndef CONFIG_CPU_ARM920T
/*
* Set the processor (CP15) into 'Wait for Interrupt' mode.
- * Unlike disabling the processor clock via the PMC (above)
- * this allows the processor to be woken via JTAG.
+ * Post-RM9200 processors need this in conjunction with the above
+ * to save power when idle.
*/
cpu_do_idle();
#endif
diff --git a/arch/arm/mach-ep93xx/dma-m2p.c b/arch/arm/mach-ep93xx/dma-m2p.c
index 8904ca4..a696d35 100644
--- a/arch/arm/mach-ep93xx/dma-m2p.c
+++ b/arch/arm/mach-ep93xx/dma-m2p.c
@@ -276,7 +276,7 @@
v &= ~(M2P_CONTROL_STALL_IRQ_EN | M2P_CONTROL_NFB_IRQ_EN);
m2p_set_control(ch, v);
- while (m2p_channel_state(ch) == STATE_ON)
+ while (m2p_channel_state(ch) >= STATE_ON)
cpu_relax();
m2p_set_control(ch, 0x0);
diff --git a/arch/arm/mach-imx/Kconfig b/arch/arm/mach-imx/Kconfig
index c5c0369..2f7e272 100644
--- a/arch/arm/mach-imx/Kconfig
+++ b/arch/arm/mach-imx/Kconfig
@@ -122,6 +122,7 @@
select IMX_HAVE_PLATFORM_IMX_I2C
select IMX_HAVE_PLATFORM_IMX_UART
select IMX_HAVE_PLATFORM_MXC_NAND
+ select MXC_ULPI if USB_ULPI
help
Include support for Eukrea CPUIMX27 platform. This includes
specific configurations for the module and its peripherals.
diff --git a/arch/arm/mach-imx/mach-cpuimx27.c b/arch/arm/mach-imx/mach-cpuimx27.c
index 339150a..6830afd 100644
--- a/arch/arm/mach-imx/mach-cpuimx27.c
+++ b/arch/arm/mach-imx/mach-cpuimx27.c
@@ -259,7 +259,7 @@
i2c_register_board_info(0, eukrea_cpuimx27_i2c_devices,
ARRAY_SIZE(eukrea_cpuimx27_i2c_devices));
- imx27_add_i2c_imx1(&cpuimx27_i2c1_data);
+ imx27_add_i2c_imx0(&cpuimx27_i2c1_data);
platform_add_devices(platform_devices, ARRAY_SIZE(platform_devices));
diff --git a/arch/arm/mach-s5p6440/cpu.c b/arch/arm/mach-s5p6440/cpu.c
index 526f33a..ec592e8 100644
--- a/arch/arm/mach-s5p6440/cpu.c
+++ b/arch/arm/mach-s5p6440/cpu.c
@@ -19,6 +19,7 @@
#include <linux/sysdev.h>
#include <linux/serial_core.h>
#include <linux/platform_device.h>
+#include <linux/sched.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
diff --git a/arch/arm/mach-s5p6442/cpu.c b/arch/arm/mach-s5p6442/cpu.c
index a48fb55..70ac681 100644
--- a/arch/arm/mach-s5p6442/cpu.c
+++ b/arch/arm/mach-s5p6442/cpu.c
@@ -19,6 +19,7 @@
#include <linux/sysdev.h>
#include <linux/serial_core.h>
#include <linux/platform_device.h>
+#include <linux/sched.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
diff --git a/arch/arm/mach-s5pc100/cpu.c b/arch/arm/mach-s5pc100/cpu.c
index 251c92a..cd1afbc 100644
--- a/arch/arm/mach-s5pc100/cpu.c
+++ b/arch/arm/mach-s5pc100/cpu.c
@@ -21,6 +21,7 @@
#include <linux/sysdev.h>
#include <linux/serial_core.h>
#include <linux/platform_device.h>
+#include <linux/sched.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
diff --git a/arch/arm/mach-s5pv210/clock.c b/arch/arm/mach-s5pv210/clock.c
index cfecd70..d562670 100644
--- a/arch/arm/mach-s5pv210/clock.c
+++ b/arch/arm/mach-s5pv210/clock.c
@@ -173,11 +173,6 @@
return s5p_gatectrl(S5P_CLKGATE_IP3, clk, enable);
}
-static int s5pv210_clk_ip4_ctrl(struct clk *clk, int enable)
-{
- return s5p_gatectrl(S5P_CLKGATE_IP4, clk, enable);
-}
-
static int s5pv210_clk_mask0_ctrl(struct clk *clk, int enable)
{
return s5p_gatectrl(S5P_CLK_SRC_MASK0, clk, enable);
diff --git a/arch/arm/mach-s5pv210/cpu.c b/arch/arm/mach-s5pv210/cpu.c
index 77f456c..245b82b 100644
--- a/arch/arm/mach-s5pv210/cpu.c
+++ b/arch/arm/mach-s5pv210/cpu.c
@@ -19,6 +19,7 @@
#include <linux/io.h>
#include <linux/sysdev.h>
#include <linux/platform_device.h>
+#include <linux/sched.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
diff --git a/arch/arm/mach-vexpress/ct-ca9x4.c b/arch/arm/mach-vexpress/ct-ca9x4.c
index efb1270..71fb173 100644
--- a/arch/arm/mach-vexpress/ct-ca9x4.c
+++ b/arch/arm/mach-vexpress/ct-ca9x4.c
@@ -68,7 +68,7 @@
}
#if 0
-static void ct_ca9x4_timer_init(void)
+static void __init ct_ca9x4_timer_init(void)
{
writel(0, MMIO_P2V(CT_CA9X4_TIMER0) + TIMER_CTRL);
writel(0, MMIO_P2V(CT_CA9X4_TIMER1) + TIMER_CTRL);
@@ -222,7 +222,7 @@
.resource = pmu_resources,
};
-static void ct_ca9x4_init(void)
+static void __init ct_ca9x4_init(void)
{
int i;
diff --git a/arch/arm/mach-vexpress/v2m.c b/arch/arm/mach-vexpress/v2m.c
index 817f0ad..7eaa232 100644
--- a/arch/arm/mach-vexpress/v2m.c
+++ b/arch/arm/mach-vexpress/v2m.c
@@ -48,7 +48,7 @@
}
-static void v2m_timer_init(void)
+static void __init v2m_timer_init(void)
{
writel(0, MMIO_P2V(V2M_TIMER0) + TIMER_CTRL);
writel(0, MMIO_P2V(V2M_TIMER1) + TIMER_CTRL);
diff --git a/arch/arm/mm/ioremap.c b/arch/arm/mm/ioremap.c
index ab50627..17e7b0b 100644
--- a/arch/arm/mm/ioremap.c
+++ b/arch/arm/mm/ioremap.c
@@ -204,8 +204,12 @@
/*
* Don't allow RAM to be mapped - this causes problems with ARMv6+
*/
- if (WARN_ON(pfn_valid(pfn)))
- return NULL;
+ if (pfn_valid(pfn)) {
+ printk(KERN_WARNING "BUG: Your driver calls ioremap() on system memory. This leads\n"
+ KERN_WARNING "to architecturally unpredictable behaviour on ARMv6+, and ioremap()\n"
+ KERN_WARNING "will fail in the next kernel release. Please fix your driver.\n");
+ WARN_ON(1);
+ }
type = get_mem_type(mtype);
if (!type)
diff --git a/arch/arm/mm/mmu.c b/arch/arm/mm/mmu.c
index 6a3a2d0..e8ed9dc 100644
--- a/arch/arm/mm/mmu.c
+++ b/arch/arm/mm/mmu.c
@@ -248,7 +248,7 @@
},
[MT_MEMORY] = {
.prot_pte = L_PTE_PRESENT | L_PTE_YOUNG | L_PTE_DIRTY |
- L_PTE_USER | L_PTE_EXEC,
+ L_PTE_WRITE | L_PTE_EXEC,
.prot_l1 = PMD_TYPE_TABLE,
.prot_sect = PMD_TYPE_SECT | PMD_SECT_AP_WRITE,
.domain = DOMAIN_KERNEL,
@@ -259,7 +259,7 @@
},
[MT_MEMORY_NONCACHED] = {
.prot_pte = L_PTE_PRESENT | L_PTE_YOUNG | L_PTE_DIRTY |
- L_PTE_USER | L_PTE_EXEC | L_PTE_MT_BUFFERABLE,
+ L_PTE_WRITE | L_PTE_EXEC | L_PTE_MT_BUFFERABLE,
.prot_l1 = PMD_TYPE_TABLE,
.prot_sect = PMD_TYPE_SECT | PMD_SECT_AP_WRITE,
.domain = DOMAIN_KERNEL,
diff --git a/arch/arm/mm/proc-v7.S b/arch/arm/mm/proc-v7.S
index 7563ff0..197f21b 100644
--- a/arch/arm/mm/proc-v7.S
+++ b/arch/arm/mm/proc-v7.S
@@ -253,6 +253,14 @@
orreq r10, r10, #1 << 22 @ set bit #22
mcreq p15, 0, r10, c15, c0, 1 @ write diagnostic register
#endif
+#ifdef CONFIG_ARM_ERRATA_743622
+ teq r6, #0x20 @ present in r2p0
+ teqne r6, #0x21 @ present in r2p1
+ teqne r6, #0x22 @ present in r2p2
+ mrceq p15, 0, r10, c15, c0, 1 @ read diagnostic register
+ orreq r10, r10, #1 << 6 @ set bit #6
+ mcreq p15, 0, r10, c15, c0, 1 @ write diagnostic register
+#endif
3: mov r10, #0
#ifdef HARVARD_CACHE
@@ -365,7 +373,7 @@
b __v7_ca9mp_setup
.long cpu_arch_name
.long cpu_elf_name
- .long HWCAP_SWP|HWCAP_HALF|HWCAP_THUMB|HWCAP_FAST_MULT|HWCAP_EDSP
+ .long HWCAP_SWP|HWCAP_HALF|HWCAP_THUMB|HWCAP_FAST_MULT|HWCAP_EDSP|HWCAP_TLS
.long cpu_v7_name
.long v7_processor_functions
.long v7wbi_tlb_fns
diff --git a/arch/arm/oprofile/common.c b/arch/arm/oprofile/common.c
index 0691176..72e09eb 100644
--- a/arch/arm/oprofile/common.c
+++ b/arch/arm/oprofile/common.c
@@ -102,6 +102,7 @@
if (IS_ERR(pevent)) {
ret = PTR_ERR(pevent);
} else if (pevent->state != PERF_EVENT_STATE_ACTIVE) {
+ perf_event_release_kernel(pevent);
pr_warning("oprofile: failed to enable event %d "
"on CPU %d\n", event, cpu);
ret = -EBUSY;
@@ -365,6 +366,7 @@
ret = init_driverfs();
if (ret) {
kfree(counter_config);
+ counter_config = NULL;
return ret;
}
@@ -402,7 +404,6 @@
struct perf_event *event;
if (*perf_events) {
- exit_driverfs();
for_each_possible_cpu(cpu) {
for (id = 0; id < perf_num_counters; ++id) {
event = perf_events[cpu][id];
@@ -413,8 +414,10 @@
}
}
- if (counter_config)
+ if (counter_config) {
kfree(counter_config);
+ exit_driverfs();
+ }
}
#else
int __init oprofile_arch_init(struct oprofile_operations *ops)
diff --git a/arch/arm/plat-omap/iommu.c b/arch/arm/plat-omap/iommu.c
index a202a2c..6cd151b 100644
--- a/arch/arm/plat-omap/iommu.c
+++ b/arch/arm/plat-omap/iommu.c
@@ -320,6 +320,7 @@
if ((start <= da) && (da < start + bytes)) {
dev_dbg(obj->dev, "%s: %08x<=%08x(%x)\n",
__func__, start, da, bytes);
+ iotlb_load_cr(obj, &cr);
iommu_write_reg(obj, 1, MMU_FLUSH_ENTRY);
}
}
diff --git a/arch/arm/plat-samsung/adc.c b/arch/arm/plat-samsung/adc.c
index 04d9521..e8f2be2 100644
--- a/arch/arm/plat-samsung/adc.c
+++ b/arch/arm/plat-samsung/adc.c
@@ -435,7 +435,6 @@
static int s3c_adc_resume(struct platform_device *pdev)
{
struct adc_device *adc = platform_get_drvdata(pdev);
- unsigned long flags;
clk_enable(adc->clk);
enable_irq(adc->irq);
diff --git a/arch/arm/plat-samsung/clock.c b/arch/arm/plat-samsung/clock.c
index 90a2051..e8d20b0 100644
--- a/arch/arm/plat-samsung/clock.c
+++ b/arch/arm/plat-samsung/clock.c
@@ -48,6 +48,9 @@
#include <plat/clock.h>
#include <plat/cpu.h>
+#include <linux/serial_core.h>
+#include <plat/regs-serial.h> /* for s3c24xx_uart_devs */
+
/* clock information */
static LIST_HEAD(clocks);
@@ -65,6 +68,28 @@
return 0;
}
+static int dev_is_s3c_uart(struct device *dev)
+{
+ struct platform_device **pdev = s3c24xx_uart_devs;
+ int i;
+ for (i = 0; i < ARRAY_SIZE(s3c24xx_uart_devs); i++, pdev++)
+ if (*pdev && dev == &(*pdev)->dev)
+ return 1;
+ return 0;
+}
+
+/*
+ * Serial drivers call get_clock() very early, before platform bus
+ * has been set up, this requires a special check to let them get
+ * a proper clock
+ */
+
+static int dev_is_platform_device(struct device *dev)
+{
+ return dev->bus == &platform_bus_type ||
+ (dev->bus == NULL && dev_is_s3c_uart(dev));
+}
+
/* Clock API calls */
struct clk *clk_get(struct device *dev, const char *id)
@@ -73,7 +98,7 @@
struct clk *clk = ERR_PTR(-ENOENT);
int idno;
- if (dev == NULL || dev->bus != &platform_bus_type)
+ if (dev == NULL || !dev_is_platform_device(dev))
idno = -1;
else
idno = to_platform_device(dev)->id;
diff --git a/arch/avr32/kernel/module.c b/arch/avr32/kernel/module.c
index 98f94d0..a727f54 100644
--- a/arch/avr32/kernel/module.c
+++ b/arch/avr32/kernel/module.c
@@ -314,10 +314,9 @@
vfree(module->arch.syminfo);
module->arch.syminfo = NULL;
- return module_bug_finalize(hdr, sechdrs, module);
+ return 0;
}
void module_arch_cleanup(struct module *module)
{
- module_bug_cleanup(module);
}
diff --git a/arch/h8300/kernel/module.c b/arch/h8300/kernel/module.c
index 0865e29..db4953d 100644
--- a/arch/h8300/kernel/module.c
+++ b/arch/h8300/kernel/module.c
@@ -112,10 +112,9 @@
const Elf_Shdr *sechdrs,
struct module *me)
{
- return module_bug_finalize(hdr, sechdrs, me);
+ return 0;
}
void module_arch_cleanup(struct module *mod)
{
- module_bug_cleanup(mod);
}
diff --git a/arch/m32r/include/asm/elf.h b/arch/m32r/include/asm/elf.h
index 2f85412..b8da7d0 100644
--- a/arch/m32r/include/asm/elf.h
+++ b/arch/m32r/include/asm/elf.h
@@ -82,9 +82,9 @@
* These are used to set parameters in the core dumps.
*/
#define ELF_CLASS ELFCLASS32
-#if defined(__LITTLE_ENDIAN)
+#if defined(__LITTLE_ENDIAN__)
#define ELF_DATA ELFDATA2LSB
-#elif defined(__BIG_ENDIAN)
+#elif defined(__BIG_ENDIAN__)
#define ELF_DATA ELFDATA2MSB
#else
#error no endian defined
diff --git a/arch/m32r/kernel/.gitignore b/arch/m32r/kernel/.gitignore
new file mode 100644
index 0000000..c5f676c
--- /dev/null
+++ b/arch/m32r/kernel/.gitignore
@@ -0,0 +1 @@
+vmlinux.lds
diff --git a/arch/m32r/kernel/signal.c b/arch/m32r/kernel/signal.c
index 7bbe386..a08697f 100644
--- a/arch/m32r/kernel/signal.c
+++ b/arch/m32r/kernel/signal.c
@@ -28,6 +28,8 @@
#define DEBUG_SIG 0
+#define _BLOCKABLE (~(sigmask(SIGKILL) | sigmask(SIGSTOP)))
+
asmlinkage int
sys_sigaltstack(const stack_t __user *uss, stack_t __user *uoss,
unsigned long r2, unsigned long r3, unsigned long r4,
@@ -254,7 +256,7 @@
static int prev_insn(struct pt_regs *regs)
{
u16 inst;
- if (get_user(&inst, (u16 __user *)(regs->bpc - 2)))
+ if (get_user(inst, (u16 __user *)(regs->bpc - 2)))
return -EFAULT;
if ((inst & 0xfff0) == 0x10f0) /* trap ? */
regs->bpc -= 2;
diff --git a/arch/mips/Kconfig b/arch/mips/Kconfig
index 2d3cf38..4c9f402 100644
--- a/arch/mips/Kconfig
+++ b/arch/mips/Kconfig
@@ -13,6 +13,7 @@
select HAVE_KPROBES
select HAVE_KRETPROBES
select RTC_LIB if !MACH_LOONGSON
+ select GENERIC_ATOMIC64 if !64BIT
mainmenu "Linux/MIPS Kernel Configuration"
@@ -1650,8 +1651,16 @@
select SYS_SUPPORTS_SMP
select SMP_UP
help
- This is a kernel model which is also known a VSMP or lately
- has been marketesed into SMVP.
+ This is a kernel model which is known a VSMP but lately has been
+ marketesed into SMVP.
+ Virtual SMP uses the processor's VPEs to implement virtual
+ processors. In currently available configuration of the 34K processor
+ this allows for a dual processor. Both processors will share the same
+ primary caches; each will obtain the half of the TLB for it's own
+ exclusive use. For a layman this model can be described as similar to
+ what Intel calls Hyperthreading.
+
+ For further information see http://www.linux-mips.org/wiki/34K#VSMP
config MIPS_MT_SMTC
bool "SMTC: Use all TCs on all VPEs for SMP"
@@ -1668,6 +1677,14 @@
help
This is a kernel model which is known a SMTC or lately has been
marketesed into SMVP.
+ is presenting the available TC's of the core as processors to Linux.
+ On currently available 34K processors this means a Linux system will
+ see up to 5 processors. The implementation of the SMTC kernel differs
+ significantly from VSMP and cannot efficiently coexist in the same
+ kernel binary so the choice between VSMP and SMTC is a compile time
+ decision.
+
+ For further information see http://www.linux-mips.org/wiki/34K#SMTC
endchoice
diff --git a/arch/mips/alchemy/common/prom.c b/arch/mips/alchemy/common/prom.c
index c29511b..5340210 100644
--- a/arch/mips/alchemy/common/prom.c
+++ b/arch/mips/alchemy/common/prom.c
@@ -43,7 +43,7 @@
char **prom_argv;
char **prom_envp;
-void prom_init_cmdline(void)
+void __init prom_init_cmdline(void)
{
int i;
@@ -104,7 +104,7 @@
}
}
-int prom_get_ethernet_addr(char *ethernet_addr)
+int __init prom_get_ethernet_addr(char *ethernet_addr)
{
char *ethaddr_str;
@@ -123,7 +123,6 @@
return 0;
}
-EXPORT_SYMBOL(prom_get_ethernet_addr);
void __init prom_free_prom_memory(void)
{
diff --git a/arch/mips/boot/compressed/Makefile b/arch/mips/boot/compressed/Makefile
index 4df4c77..5042d51 100644
--- a/arch/mips/boot/compressed/Makefile
+++ b/arch/mips/boot/compressed/Makefile
@@ -59,7 +59,7 @@
hostprogs-y := calc_vmlinuz_load_addr
VMLINUZ_LOAD_ADDRESS = $(shell $(obj)/calc_vmlinuz_load_addr \
- $(objtree)/$(KBUILD_IMAGE) $(VMLINUX_LOAD_ADDRESS))
+ $(obj)/vmlinux.bin $(VMLINUX_LOAD_ADDRESS))
vmlinuzobjs-y += $(obj)/piggy.o
diff --git a/arch/mips/cavium-octeon/Kconfig b/arch/mips/cavium-octeon/Kconfig
index 094c17e..47323ca 100644
--- a/arch/mips/cavium-octeon/Kconfig
+++ b/arch/mips/cavium-octeon/Kconfig
@@ -83,3 +83,7 @@
def_bool y
select SPARSEMEM_STATIC
depends on CPU_CAVIUM_OCTEON
+
+config CAVIUM_OCTEON_HELPER
+ def_bool y
+ depends on OCTEON_ETHERNET || PCI
diff --git a/arch/mips/cavium-octeon/cpu.c b/arch/mips/cavium-octeon/cpu.c
index c664c8c..a5b4279 100644
--- a/arch/mips/cavium-octeon/cpu.c
+++ b/arch/mips/cavium-octeon/cpu.c
@@ -41,7 +41,7 @@
return NOTIFY_OK; /* Let default notifier send signals */
}
-static int cnmips_cu2_setup(void)
+static int __init cnmips_cu2_setup(void)
{
return cu2_notifier(cnmips_cu2_call, 0);
}
diff --git a/arch/mips/cavium-octeon/executive/Makefile b/arch/mips/cavium-octeon/executive/Makefile
index 2fd66db..7f41c5b 100644
--- a/arch/mips/cavium-octeon/executive/Makefile
+++ b/arch/mips/cavium-octeon/executive/Makefile
@@ -11,4 +11,4 @@
obj-y += cvmx-bootmem.o cvmx-l2c.o cvmx-sysinfo.o octeon-model.o
-obj-$(CONFIG_PCI) += cvmx-helper-errata.o cvmx-helper-jtag.o
+obj-$(CONFIG_CAVIUM_OCTEON_HELPER) += cvmx-helper-errata.o cvmx-helper-jtag.o
diff --git a/arch/mips/include/asm/atomic.h b/arch/mips/include/asm/atomic.h
index c63c56b..47d87da 100644
--- a/arch/mips/include/asm/atomic.h
+++ b/arch/mips/include/asm/atomic.h
@@ -782,6 +782,10 @@
*/
#define atomic64_add_negative(i, v) (atomic64_add_return(i, (v)) < 0)
+#else /* !CONFIG_64BIT */
+
+#include <asm-generic/atomic64.h>
+
#endif /* CONFIG_64BIT */
/*
diff --git a/arch/mips/include/asm/cop2.h b/arch/mips/include/asm/cop2.h
index 2cb2f0c..3532e2c 100644
--- a/arch/mips/include/asm/cop2.h
+++ b/arch/mips/include/asm/cop2.h
@@ -24,7 +24,7 @@
#define cu2_notifier(fn, pri) \
({ \
- static struct notifier_block fn##_nb __cpuinitdata = { \
+ static struct notifier_block fn##_nb = { \
.notifier_call = fn, \
.priority = pri \
}; \
diff --git a/arch/mips/include/asm/gic.h b/arch/mips/include/asm/gic.h
index 9b9436a..86548da 100644
--- a/arch/mips/include/asm/gic.h
+++ b/arch/mips/include/asm/gic.h
@@ -321,6 +321,7 @@
*/
struct gic_intr_map {
unsigned int cpunum; /* Directed to this CPU */
+#define GIC_UNUSED 0xdead /* Dummy data */
unsigned int pin; /* Directed to this Pin */
unsigned int polarity; /* Polarity : +/- */
unsigned int trigtype; /* Trigger : Edge/Levl */
diff --git a/arch/mips/include/asm/mach-tx49xx/kmalloc.h b/arch/mips/include/asm/mach-tx49xx/kmalloc.h
index b74caf6..ff9a8b86 100644
--- a/arch/mips/include/asm/mach-tx49xx/kmalloc.h
+++ b/arch/mips/include/asm/mach-tx49xx/kmalloc.h
@@ -1,6 +1,6 @@
#ifndef __ASM_MACH_TX49XX_KMALLOC_H
#define __ASM_MACH_TX49XX_KMALLOC_H
-#define ARCH_KMALLOC_MINALIGN L1_CACHE_BYTES
+#define ARCH_DMA_MINALIGN L1_CACHE_BYTES
#endif /* __ASM_MACH_TX49XX_KMALLOC_H */
diff --git a/arch/mips/include/asm/mips-boards/maltaint.h b/arch/mips/include/asm/mips-boards/maltaint.h
index cea872f..d11aa02 100644
--- a/arch/mips/include/asm/mips-boards/maltaint.h
+++ b/arch/mips/include/asm/mips-boards/maltaint.h
@@ -88,9 +88,6 @@
#define GIC_EXT_INTR(x) x
-/* Dummy data */
-#define X 0xdead
-
/* External Interrupts used for IPI */
#define GIC_IPI_EXT_INTR_RESCHED_VPE0 16
#define GIC_IPI_EXT_INTR_CALLFNC_VPE0 17
diff --git a/arch/mips/include/asm/page.h b/arch/mips/include/asm/page.h
index a16beaf..e59cd1a 100644
--- a/arch/mips/include/asm/page.h
+++ b/arch/mips/include/asm/page.h
@@ -150,6 +150,20 @@
((unsigned long)(x) - PAGE_OFFSET + PHYS_OFFSET)
#endif
#define __va(x) ((void *)((unsigned long)(x) + PAGE_OFFSET - PHYS_OFFSET))
+
+/*
+ * RELOC_HIDE was originally added by 6007b903dfe5f1d13e0c711ac2894bdd4a61b1ad
+ * (lmo) rsp. 8431fd094d625b94d364fe393076ccef88e6ce18 (kernel.org). The
+ * discussion can be found in lkml posting
+ * <a2ebde260608230500o3407b108hc03debb9da6e62c@mail.gmail.com> which is
+ * archived at http://lists.linuxcoding.com/kernel/2006-q3/msg17360.html
+ *
+ * It is unclear if the misscompilations mentioned in
+ * http://lkml.org/lkml/2010/8/8/138 also affect MIPS so we keep this one
+ * until GCC 3.x has been retired before we can apply
+ * https://patchwork.linux-mips.org/patch/1541/
+ */
+
#define __pa_symbol(x) __pa(RELOC_HIDE((unsigned long)(x), 0))
#define pfn_to_kaddr(pfn) __va((pfn) << PAGE_SHIFT)
diff --git a/arch/mips/include/asm/siginfo.h b/arch/mips/include/asm/siginfo.h
index 96e28f1..1ca64b4 100644
--- a/arch/mips/include/asm/siginfo.h
+++ b/arch/mips/include/asm/siginfo.h
@@ -88,6 +88,7 @@
#ifdef __ARCH_SI_TRAPNO
int _trapno; /* TRAP # which caused the signal */
#endif
+ short _addr_lsb;
} _sigfault;
/* SIGPOLL, SIGXFSZ (To do ...) */
diff --git a/arch/mips/include/asm/thread_info.h b/arch/mips/include/asm/thread_info.h
index 2376f2e..70df9c0 100644
--- a/arch/mips/include/asm/thread_info.h
+++ b/arch/mips/include/asm/thread_info.h
@@ -146,7 +146,8 @@
#define _TIF_LOAD_WATCH (1<<TIF_LOAD_WATCH)
/* work to do on interrupt/exception return */
-#define _TIF_WORK_MASK (0x0000ffef & ~_TIF_SECCOMP)
+#define _TIF_WORK_MASK (0x0000ffef & \
+ ~(_TIF_SECCOMP | _TIF_SYSCALL_AUDIT))
/* work to do on any return to u-space */
#define _TIF_ALLWORK_MASK (0x8000ffff & ~_TIF_SECCOMP)
diff --git a/arch/mips/include/asm/unistd.h b/arch/mips/include/asm/unistd.h
index baa318a..550725b 100644
--- a/arch/mips/include/asm/unistd.h
+++ b/arch/mips/include/asm/unistd.h
@@ -356,16 +356,19 @@
#define __NR_perf_event_open (__NR_Linux + 333)
#define __NR_accept4 (__NR_Linux + 334)
#define __NR_recvmmsg (__NR_Linux + 335)
+#define __NR_fanotify_init (__NR_Linux + 336)
+#define __NR_fanotify_mark (__NR_Linux + 337)
+#define __NR_prlimit64 (__NR_Linux + 338)
/*
* Offset of the last Linux o32 flavoured syscall
*/
-#define __NR_Linux_syscalls 335
+#define __NR_Linux_syscalls 338
#endif /* _MIPS_SIM == _MIPS_SIM_ABI32 */
#define __NR_O32_Linux 4000
-#define __NR_O32_Linux_syscalls 335
+#define __NR_O32_Linux_syscalls 338
#if _MIPS_SIM == _MIPS_SIM_ABI64
@@ -668,16 +671,19 @@
#define __NR_perf_event_open (__NR_Linux + 292)
#define __NR_accept4 (__NR_Linux + 293)
#define __NR_recvmmsg (__NR_Linux + 294)
+#define __NR_fanotify_init (__NR_Linux + 295)
+#define __NR_fanotify_mark (__NR_Linux + 296)
+#define __NR_prlimit64 (__NR_Linux + 297)
/*
* Offset of the last Linux 64-bit flavoured syscall
*/
-#define __NR_Linux_syscalls 294
+#define __NR_Linux_syscalls 297
#endif /* _MIPS_SIM == _MIPS_SIM_ABI64 */
#define __NR_64_Linux 5000
-#define __NR_64_Linux_syscalls 294
+#define __NR_64_Linux_syscalls 297
#if _MIPS_SIM == _MIPS_SIM_NABI32
@@ -985,16 +991,19 @@
#define __NR_accept4 (__NR_Linux + 297)
#define __NR_recvmmsg (__NR_Linux + 298)
#define __NR_getdents64 (__NR_Linux + 299)
+#define __NR_fanotify_init (__NR_Linux + 300)
+#define __NR_fanotify_mark (__NR_Linux + 301)
+#define __NR_prlimit64 (__NR_Linux + 302)
/*
* Offset of the last N32 flavoured syscall
*/
-#define __NR_Linux_syscalls 299
+#define __NR_Linux_syscalls 302
#endif /* _MIPS_SIM == _MIPS_SIM_NABI32 */
#define __NR_N32_Linux 6000
-#define __NR_N32_Linux_syscalls 299
+#define __NR_N32_Linux_syscalls 302
#ifdef __KERNEL__
diff --git a/arch/mips/kernel/irq-gic.c b/arch/mips/kernel/irq-gic.c
index b181f2f..82ba9f6 100644
--- a/arch/mips/kernel/irq-gic.c
+++ b/arch/mips/kernel/irq-gic.c
@@ -7,7 +7,6 @@
#include <asm/io.h>
#include <asm/gic.h>
#include <asm/gcmpregs.h>
-#include <asm/mips-boards/maltaint.h>
#include <asm/irq.h>
#include <linux/hardirq.h>
#include <asm-generic/bitops/find.h>
@@ -131,7 +130,7 @@
int i;
irq -= _irqbase;
- pr_debug(KERN_DEBUG "%s(%d) called\n", __func__, irq);
+ pr_debug("%s(%d) called\n", __func__, irq);
cpumask_and(&tmp, cpumask, cpu_online_mask);
if (cpus_empty(tmp))
return -1;
@@ -222,7 +221,7 @@
/* Setup specifics */
for (i = 0; i < mapsize; i++) {
cpu = intrmap[i].cpunum;
- if (cpu == X)
+ if (cpu == GIC_UNUSED)
continue;
if (cpu == 0 && i != 0 && intrmap[i].flags == 0)
continue;
diff --git a/arch/mips/kernel/kgdb.c b/arch/mips/kernel/kgdb.c
index 1f4e2fa..f4546e9 100644
--- a/arch/mips/kernel/kgdb.c
+++ b/arch/mips/kernel/kgdb.c
@@ -283,7 +283,7 @@
struct pt_regs *regs = args->regs;
int trap = (regs->cp0_cause & 0x7c) >> 2;
- /* Userpace events, ignore. */
+ /* Userspace events, ignore. */
if (user_mode(regs))
return NOTIFY_DONE;
diff --git a/arch/mips/kernel/kspd.c b/arch/mips/kernel/kspd.c
index 80e2ba6..29811f0 100644
--- a/arch/mips/kernel/kspd.c
+++ b/arch/mips/kernel/kspd.c
@@ -251,7 +251,7 @@
memset(&tz, 0, sizeof(tz));
if ((ret.retval = sp_syscall(__NR_gettimeofday, (int)&tv,
(int)&tz, 0, 0)) == 0)
- ret.retval = tv.tv_sec;
+ ret.retval = tv.tv_sec;
break;
case MTSP_SYSCALL_EXIT:
diff --git a/arch/mips/kernel/linux32.c b/arch/mips/kernel/linux32.c
index c2dab14..6343b4a 100644
--- a/arch/mips/kernel/linux32.c
+++ b/arch/mips/kernel/linux32.c
@@ -341,3 +341,10 @@
{
return sys_lookup_dcookie(merge_64(a0, a1), buf, len);
}
+
+SYSCALL_DEFINE6(32_fanotify_mark, int, fanotify_fd, unsigned int, flags,
+ u64, a3, u64, a4, int, dfd, const char __user *, pathname)
+{
+ return sys_fanotify_mark(fanotify_fd, flags, merge_64(a3, a4),
+ dfd, pathname);
+}
diff --git a/arch/mips/kernel/scall32-o32.S b/arch/mips/kernel/scall32-o32.S
index 84b4179..fbaabad 100644
--- a/arch/mips/kernel/scall32-o32.S
+++ b/arch/mips/kernel/scall32-o32.S
@@ -582,7 +582,10 @@
sys sys_rt_tgsigqueueinfo 4
sys sys_perf_event_open 5
sys sys_accept4 4
- sys sys_recvmmsg 5
+ sys sys_recvmmsg 5 /* 4335 */
+ sys sys_fanotify_init 2
+ sys sys_fanotify_mark 6
+ sys sys_prlimit64 4
.endm
/* We pre-compute the number of _instruction_ bytes needed to
diff --git a/arch/mips/kernel/scall64-64.S b/arch/mips/kernel/scall64-64.S
index eb0bb73..3f41792 100644
--- a/arch/mips/kernel/scall64-64.S
+++ b/arch/mips/kernel/scall64-64.S
@@ -417,9 +417,12 @@
PTR sys_pipe2
PTR sys_inotify_init1
PTR sys_preadv
- PTR sys_pwritev /* 5390 */
+ PTR sys_pwritev /* 5290 */
PTR sys_rt_tgsigqueueinfo
PTR sys_perf_event_open
PTR sys_accept4
- PTR sys_recvmmsg
+ PTR sys_recvmmsg
+ PTR sys_fanotify_init /* 5295 */
+ PTR sys_fanotify_mark
+ PTR sys_prlimit64
.size sys_call_table,.-sys_call_table
diff --git a/arch/mips/kernel/scall64-n32.S b/arch/mips/kernel/scall64-n32.S
index 4da3faf..38b2269 100644
--- a/arch/mips/kernel/scall64-n32.S
+++ b/arch/mips/kernel/scall64-n32.S
@@ -421,5 +421,8 @@
PTR sys_perf_event_open
PTR sys_accept4
PTR compat_sys_recvmmsg
- PTR sys_getdents
+ PTR sys_getdents64
+ PTR sys_fanotify_init /* 6300 */
+ PTR sys_fanotify_mark
+ PTR sys_prlimit64
.size sysn32_call_table,.-sysn32_call_table
diff --git a/arch/mips/kernel/scall64-o32.S b/arch/mips/kernel/scall64-o32.S
index d2bc285..42fe14b 100644
--- a/arch/mips/kernel/scall64-o32.S
+++ b/arch/mips/kernel/scall64-o32.S
@@ -539,5 +539,8 @@
PTR compat_sys_rt_tgsigqueueinfo
PTR sys_perf_event_open
PTR sys_accept4
- PTR compat_sys_recvmmsg
+ PTR compat_sys_recvmmsg /* 4335 */
+ PTR sys_fanotify_init
+ PTR sys_32_fanotify_mark
+ PTR sys_prlimit64
.size sys_call_table,.-sys_call_table
diff --git a/arch/mips/mm/dma-default.c b/arch/mips/mm/dma-default.c
index 7ba8908..469d401 100644
--- a/arch/mips/mm/dma-default.c
+++ b/arch/mips/mm/dma-default.c
@@ -44,27 +44,39 @@
static gfp_t massage_gfp_flags(const struct device *dev, gfp_t gfp)
{
+ gfp_t dma_flag;
+
/* ignore region specifiers */
gfp &= ~(__GFP_DMA | __GFP_DMA32 | __GFP_HIGHMEM);
-#ifdef CONFIG_ZONE_DMA
+#ifdef CONFIG_ISA
if (dev == NULL)
- gfp |= __GFP_DMA;
- else if (dev->coherent_dma_mask < DMA_BIT_MASK(24))
- gfp |= __GFP_DMA;
+ dma_flag = __GFP_DMA;
else
#endif
-#ifdef CONFIG_ZONE_DMA32
+#if defined(CONFIG_ZONE_DMA32) && defined(CONFIG_ZONE_DMA)
if (dev->coherent_dma_mask < DMA_BIT_MASK(32))
- gfp |= __GFP_DMA32;
+ dma_flag = __GFP_DMA;
+ else if (dev->coherent_dma_mask < DMA_BIT_MASK(64))
+ dma_flag = __GFP_DMA32;
else
#endif
- ;
+#if defined(CONFIG_ZONE_DMA32) && !defined(CONFIG_ZONE_DMA)
+ if (dev->coherent_dma_mask < DMA_BIT_MASK(64))
+ dma_flag = __GFP_DMA32;
+ else
+#endif
+#if defined(CONFIG_ZONE_DMA) && !defined(CONFIG_ZONE_DMA32)
+ if (dev->coherent_dma_mask < DMA_BIT_MASK(64))
+ dma_flag = __GFP_DMA;
+ else
+#endif
+ dma_flag = 0;
/* Don't invoke OOM killer */
gfp |= __GFP_NORETRY;
- return gfp;
+ return gfp | dma_flag;
}
void *dma_alloc_noncoherent(struct device *dev, size_t size,
diff --git a/arch/mips/mm/sc-rm7k.c b/arch/mips/mm/sc-rm7k.c
index 1ef75cd..274af3b 100644
--- a/arch/mips/mm/sc-rm7k.c
+++ b/arch/mips/mm/sc-rm7k.c
@@ -30,7 +30,7 @@
#define tc_lsize 32
extern unsigned long icache_way_size, dcache_way_size;
-unsigned long tcache_size;
+static unsigned long tcache_size;
#include <asm/r4kcache.h>
diff --git a/arch/mips/mti-malta/malta-int.c b/arch/mips/mti-malta/malta-int.c
index 15949b0..b79b24a 100644
--- a/arch/mips/mti-malta/malta-int.c
+++ b/arch/mips/mti-malta/malta-int.c
@@ -385,6 +385,8 @@
*/
#define GIC_CPU_NMI GIC_MAP_TO_NMI_MSK
+#define X GIC_UNUSED
+
static struct gic_intr_map gic_intr_map[GIC_NUM_INTRS] = {
{ X, X, X, X, 0 },
{ X, X, X, X, 0 },
@@ -404,6 +406,7 @@
{ X, X, X, X, 0 },
/* The remainder of this table is initialised by fill_ipi_map */
};
+#undef X
/*
* GCMP needs to be detected before any SMP initialisation
diff --git a/arch/mips/pci/pci-rc32434.c b/arch/mips/pci/pci-rc32434.c
index 71f7d27..f31218e 100644
--- a/arch/mips/pci/pci-rc32434.c
+++ b/arch/mips/pci/pci-rc32434.c
@@ -118,7 +118,7 @@
if (!((pcicvalue == PCIM_H_EA) ||
(pcicvalue == PCIM_H_IA_FIX) ||
(pcicvalue == PCIM_H_IA_RR))) {
- pr_err(KERN_ERR "PCI init error!!!\n");
+ pr_err("PCI init error!!!\n");
/* Not in Host Mode, return ERROR */
return -1;
}
diff --git a/arch/mips/pnx8550/common/reset.c b/arch/mips/pnx8550/common/reset.c
index fadd8744..e7a12ff 100644
--- a/arch/mips/pnx8550/common/reset.c
+++ b/arch/mips/pnx8550/common/reset.c
@@ -22,29 +22,19 @@
*/
#include <linux/kernel.h>
+#include <asm/processor.h>
#include <asm/reboot.h>
#include <glb.h>
void pnx8550_machine_restart(char *command)
{
- char head[] = "************* Machine restart *************";
- char foot[] = "*******************************************";
-
- printk("\n\n");
- printk("%s\n", head);
- if (command != NULL)
- printk("* %s\n", command);
- printk("%s\n", foot);
-
PNX8550_RST_CTL = PNX8550_RST_DO_SW_RST;
}
void pnx8550_machine_halt(void)
{
- printk("*** Machine halt. (Not implemented) ***\n");
-}
-
-void pnx8550_machine_power_off(void)
-{
- printk("*** Machine power off. (Not implemented) ***\n");
+ while (1) {
+ if (cpu_wait)
+ cpu_wait();
+ }
}
diff --git a/arch/mips/pnx8550/common/setup.c b/arch/mips/pnx8550/common/setup.c
index 64246c9..43cb394 100644
--- a/arch/mips/pnx8550/common/setup.c
+++ b/arch/mips/pnx8550/common/setup.c
@@ -44,7 +44,6 @@
extern void __init board_setup(void);
extern void pnx8550_machine_restart(char *);
extern void pnx8550_machine_halt(void);
-extern void pnx8550_machine_power_off(void);
extern struct resource ioport_resource;
extern struct resource iomem_resource;
extern char *prom_getcmdline(void);
@@ -100,7 +99,7 @@
_machine_restart = pnx8550_machine_restart;
_machine_halt = pnx8550_machine_halt;
- pm_power_off = pnx8550_machine_power_off;
+ pm_power_off = pnx8550_machine_halt;
/* Clear the Global 2 Register, PCI Inta Output Enable Registers
Bit 1:Enable DAC Powerdown
diff --git a/arch/mn10300/kernel/module.c b/arch/mn10300/kernel/module.c
index 6aea7fd..196a111 100644
--- a/arch/mn10300/kernel/module.c
+++ b/arch/mn10300/kernel/module.c
@@ -206,7 +206,7 @@
const Elf_Shdr *sechdrs,
struct module *me)
{
- return module_bug_finalize(hdr, sechdrs, me);
+ return 0;
}
/*
@@ -214,5 +214,4 @@
*/
void module_arch_cleanup(struct module *mod)
{
- module_bug_cleanup(mod);
}
diff --git a/arch/parisc/kernel/module.c b/arch/parisc/kernel/module.c
index 159a2b8..6e81bb5 100644
--- a/arch/parisc/kernel/module.c
+++ b/arch/parisc/kernel/module.c
@@ -941,11 +941,10 @@
nsyms = newptr - (Elf_Sym *)symhdr->sh_addr;
DEBUGP("NEW num_symtab %lu\n", nsyms);
symhdr->sh_size = nsyms * sizeof(Elf_Sym);
- return module_bug_finalize(hdr, sechdrs, me);
+ return 0;
}
void module_arch_cleanup(struct module *mod)
{
deregister_unwind_table(mod);
- module_bug_cleanup(mod);
}
diff --git a/arch/powerpc/kernel/module.c b/arch/powerpc/kernel/module.c
index 477c663..49cee9d 100644
--- a/arch/powerpc/kernel/module.c
+++ b/arch/powerpc/kernel/module.c
@@ -63,11 +63,6 @@
const Elf_Shdr *sechdrs, struct module *me)
{
const Elf_Shdr *sect;
- int err;
-
- err = module_bug_finalize(hdr, sechdrs, me);
- if (err)
- return err;
/* Apply feature fixups */
sect = find_section(hdr, sechdrs, "__ftr_fixup");
@@ -101,5 +96,4 @@
void module_arch_cleanup(struct module *mod)
{
- module_bug_cleanup(mod);
}
diff --git a/arch/powerpc/platforms/512x/clock.c b/arch/powerpc/platforms/512x/clock.c
index 5b243bd..3dc2a8d 100644
--- a/arch/powerpc/platforms/512x/clock.c
+++ b/arch/powerpc/platforms/512x/clock.c
@@ -57,7 +57,7 @@
int id_match = 0;
if (dev == NULL || id == NULL)
- return NULL;
+ return clk;
mutex_lock(&clocks_mutex);
list_for_each_entry(p, &clocks, node) {
diff --git a/arch/powerpc/platforms/52xx/efika.c b/arch/powerpc/platforms/52xx/efika.c
index 45c0cb9..18c1048 100644
--- a/arch/powerpc/platforms/52xx/efika.c
+++ b/arch/powerpc/platforms/52xx/efika.c
@@ -99,7 +99,7 @@
if (bus_range == NULL || len < 2 * sizeof(int)) {
printk(KERN_WARNING EFIKA_PLATFORM_NAME
": Can't get bus-range for %s\n", pcictrl->full_name);
- return;
+ goto out_put;
}
if (bus_range[1] == bus_range[0])
@@ -111,12 +111,12 @@
printk(" controlled by %s\n", pcictrl->full_name);
printk("\n");
- hose = pcibios_alloc_controller(of_node_get(pcictrl));
+ hose = pcibios_alloc_controller(pcictrl);
if (!hose) {
printk(KERN_WARNING EFIKA_PLATFORM_NAME
": Can't allocate PCI controller structure for %s\n",
pcictrl->full_name);
- return;
+ goto out_put;
}
hose->first_busno = bus_range[0];
@@ -124,6 +124,9 @@
hose->ops = &rtas_pci_ops;
pci_process_bridge_OF_ranges(hose, pcictrl, 0);
+ return;
+out_put:
+ of_node_put(pcictrl);
}
#else
diff --git a/arch/powerpc/platforms/52xx/mpc52xx_common.c b/arch/powerpc/platforms/52xx/mpc52xx_common.c
index 6e90531..41f3a7e 100644
--- a/arch/powerpc/platforms/52xx/mpc52xx_common.c
+++ b/arch/powerpc/platforms/52xx/mpc52xx_common.c
@@ -325,12 +325,16 @@
clrbits32(&simple_gpio->simple_dvo, sync | out);
clrbits8(&wkup_gpio->wkup_dvo, reset);
- /* wait at lease 1 us */
- udelay(2);
+ /* wait for 1 us */
+ udelay(1);
/* Deassert reset */
setbits8(&wkup_gpio->wkup_dvo, reset);
+ /* wait at least 200ns */
+ /* 7 ~= (200ns * timebase) / ns2sec */
+ __delay(7);
+
/* Restore pin-muxing */
out_be32(&simple_gpio->port_config, mux);
diff --git a/arch/s390/kernel/module.c b/arch/s390/kernel/module.c
index 22cfd63..f7167ee 100644
--- a/arch/s390/kernel/module.c
+++ b/arch/s390/kernel/module.c
@@ -407,10 +407,9 @@
{
vfree(me->arch.syminfo);
me->arch.syminfo = NULL;
- return module_bug_finalize(hdr, sechdrs, me);
+ return 0;
}
void module_arch_cleanup(struct module *mod)
{
- module_bug_cleanup(mod);
}
diff --git a/arch/sh/kernel/module.c b/arch/sh/kernel/module.c
index 43adddf..ae0be69 100644
--- a/arch/sh/kernel/module.c
+++ b/arch/sh/kernel/module.c
@@ -149,13 +149,11 @@
int ret = 0;
ret |= module_dwarf_finalize(hdr, sechdrs, me);
- ret |= module_bug_finalize(hdr, sechdrs, me);
return ret;
}
void module_arch_cleanup(struct module *mod)
{
- module_bug_cleanup(mod);
module_dwarf_cleanup(mod);
}
diff --git a/arch/um/drivers/hostaudio_kern.c b/arch/um/drivers/hostaudio_kern.c
index 0c46e39..63c740a 100644
--- a/arch/um/drivers/hostaudio_kern.c
+++ b/arch/um/drivers/hostaudio_kern.c
@@ -40,6 +40,11 @@
" This is used to specify the host mixer device to the hostaudio driver.\n"\
" The default is \"" HOSTAUDIO_DEV_MIXER "\".\n\n"
+module_param(dsp, charp, 0644);
+MODULE_PARM_DESC(dsp, DSP_HELP);
+module_param(mixer, charp, 0644);
+MODULE_PARM_DESC(mixer, MIXER_HELP);
+
#ifndef MODULE
static int set_dsp(char *name, int *add)
{
@@ -56,15 +61,6 @@
}
__uml_setup("mixer=", set_mixer, "mixer=<mixer device>\n" MIXER_HELP);
-
-#else /*MODULE*/
-
-module_param(dsp, charp, 0644);
-MODULE_PARM_DESC(dsp, DSP_HELP);
-
-module_param(mixer, charp, 0644);
-MODULE_PARM_DESC(mixer, MIXER_HELP);
-
#endif
/* /dev/dsp file operations */
diff --git a/arch/um/drivers/net_kern.c b/arch/um/drivers/net_kern.c
index 2ab233b..47d0c37 100644
--- a/arch/um/drivers/net_kern.c
+++ b/arch/um/drivers/net_kern.c
@@ -255,18 +255,6 @@
netif_wake_queue(dev);
}
-static int uml_net_set_mac(struct net_device *dev, void *addr)
-{
- struct uml_net_private *lp = netdev_priv(dev);
- struct sockaddr *hwaddr = addr;
-
- spin_lock_irq(&lp->lock);
- eth_mac_addr(dev, hwaddr->sa_data);
- spin_unlock_irq(&lp->lock);
-
- return 0;
-}
-
static int uml_net_change_mtu(struct net_device *dev, int new_mtu)
{
dev->mtu = new_mtu;
@@ -373,7 +361,7 @@
.ndo_start_xmit = uml_net_start_xmit,
.ndo_set_multicast_list = uml_net_set_multicast_list,
.ndo_tx_timeout = uml_net_tx_timeout,
- .ndo_set_mac_address = uml_net_set_mac,
+ .ndo_set_mac_address = eth_mac_addr,
.ndo_change_mtu = uml_net_change_mtu,
.ndo_validate_addr = eth_validate_addr,
};
@@ -472,7 +460,8 @@
((*transport->user->init)(&lp->user, dev) != 0))
goto out_unregister;
- eth_mac_addr(dev, device->mac);
+ /* don't use eth_mac_addr, it will not work here */
+ memcpy(dev->dev_addr, device->mac, ETH_ALEN);
dev->mtu = transport->user->mtu;
dev->netdev_ops = ¨_netdev_ops;
dev->ethtool_ops = ¨_net_ethtool_ops;
diff --git a/arch/um/drivers/ubd_kern.c b/arch/um/drivers/ubd_kern.c
index 1bcd208..9734994 100644
--- a/arch/um/drivers/ubd_kern.c
+++ b/arch/um/drivers/ubd_kern.c
@@ -163,6 +163,7 @@
struct scatterlist sg[MAX_SG];
struct request *request;
int start_sg, end_sg;
+ sector_t rq_pos;
};
#define DEFAULT_COW { \
@@ -187,6 +188,7 @@
.request = NULL, \
.start_sg = 0, \
.end_sg = 0, \
+ .rq_pos = 0, \
}
/* Protected by ubd_lock */
@@ -1228,7 +1230,6 @@
{
struct io_thread_req *io_req;
struct request *req;
- sector_t sector;
int n;
while(1){
@@ -1239,12 +1240,12 @@
return;
dev->request = req;
+ dev->rq_pos = blk_rq_pos(req);
dev->start_sg = 0;
dev->end_sg = blk_rq_map_sg(q, req, dev->sg);
}
req = dev->request;
- sector = blk_rq_pos(req);
while(dev->start_sg < dev->end_sg){
struct scatterlist *sg = &dev->sg[dev->start_sg];
@@ -1256,10 +1257,9 @@
return;
}
prepare_request(req, io_req,
- (unsigned long long)sector << 9,
+ (unsigned long long)dev->rq_pos << 9,
sg->offset, sg->length, sg_page(sg));
- sector += sg->length >> 9;
n = os_write_file(thread_fd, &io_req,
sizeof(struct io_thread_req *));
if(n != sizeof(struct io_thread_req *)){
@@ -1272,6 +1272,7 @@
return;
}
+ dev->rq_pos += sg->length >> 9;
dev->start_sg++;
}
dev->end_sg = 0;
diff --git a/arch/x86/ia32/ia32_aout.c b/arch/x86/ia32/ia32_aout.c
index 0350311..2d93bdb 100644
--- a/arch/x86/ia32/ia32_aout.c
+++ b/arch/x86/ia32/ia32_aout.c
@@ -34,7 +34,7 @@
#include <asm/ia32.h>
#undef WARN_OLD
-#undef CORE_DUMP /* probably broken */
+#undef CORE_DUMP /* definitely broken */
static int load_aout_binary(struct linux_binprm *, struct pt_regs *regs);
static int load_aout_library(struct file *);
@@ -131,21 +131,15 @@
* macros to write out all the necessary info.
*/
-static int dump_write(struct file *file, const void *addr, int nr)
-{
- return file->f_op->write(file, addr, nr, &file->f_pos) == nr;
-}
+#include <linux/coredump.h>
#define DUMP_WRITE(addr, nr) \
if (!dump_write(file, (void *)(addr), (nr))) \
goto end_coredump;
-#define DUMP_SEEK(offset) \
- if (file->f_op->llseek) { \
- if (file->f_op->llseek(file, (offset), 0) != (offset)) \
- goto end_coredump; \
- } else \
- file->f_pos = (offset)
+#define DUMP_SEEK(offset) \
+ if (!dump_seek(file, offset)) \
+ goto end_coredump;
#define START_DATA() (u.u_tsize << PAGE_SHIFT)
#define START_STACK(u) (u.start_stack)
@@ -217,12 +211,6 @@
dump_size = dump.u_ssize << PAGE_SHIFT;
DUMP_WRITE(dump_start, dump_size);
}
- /*
- * Finally dump the task struct. Not be used by gdb, but
- * could be useful
- */
- set_fs(KERNEL_DS);
- DUMP_WRITE(current, sizeof(*current));
end_coredump:
set_fs(fs);
return has_dumped;
diff --git a/arch/x86/kernel/cpu/cpufreq/pcc-cpufreq.c b/arch/x86/kernel/cpu/cpufreq/pcc-cpufreq.c
index 994230d..4f6f679 100644
--- a/arch/x86/kernel/cpu/cpufreq/pcc-cpufreq.c
+++ b/arch/x86/kernel/cpu/cpufreq/pcc-cpufreq.c
@@ -368,16 +368,22 @@
return -ENODEV;
out_obj = output.pointer;
- if (out_obj->type != ACPI_TYPE_BUFFER)
- return -ENODEV;
+ if (out_obj->type != ACPI_TYPE_BUFFER) {
+ ret = -ENODEV;
+ goto out_free;
+ }
errors = *((u32 *)out_obj->buffer.pointer) & ~(1 << 0);
- if (errors)
- return -ENODEV;
+ if (errors) {
+ ret = -ENODEV;
+ goto out_free;
+ }
supported = *((u32 *)(out_obj->buffer.pointer + 4));
- if (!(supported & 0x1))
- return -ENODEV;
+ if (!(supported & 0x1)) {
+ ret = -ENODEV;
+ goto out_free;
+ }
out_free:
kfree(output.pointer);
diff --git a/arch/x86/kernel/cpu/mcheck/mce_amd.c b/arch/x86/kernel/cpu/mcheck/mce_amd.c
index 5e97529..39aaee5 100644
--- a/arch/x86/kernel/cpu/mcheck/mce_amd.c
+++ b/arch/x86/kernel/cpu/mcheck/mce_amd.c
@@ -141,6 +141,7 @@
address = (low & MASK_BLKPTR_LO) >> 21;
if (!address)
break;
+
address += MCG_XBLK_ADDR;
} else
++address;
@@ -148,12 +149,8 @@
if (rdmsr_safe(address, &low, &high))
break;
- if (!(high & MASK_VALID_HI)) {
- if (block)
- continue;
- else
- break;
- }
+ if (!(high & MASK_VALID_HI))
+ continue;
if (!(high & MASK_CNTP_HI) ||
(high & MASK_LOCKED_HI))
diff --git a/arch/x86/kernel/cpu/mcheck/therm_throt.c b/arch/x86/kernel/cpu/mcheck/therm_throt.c
index d9368ee..169d880 100644
--- a/arch/x86/kernel/cpu/mcheck/therm_throt.c
+++ b/arch/x86/kernel/cpu/mcheck/therm_throt.c
@@ -216,7 +216,7 @@
err = sysfs_add_file_to_group(&sys_dev->kobj,
&attr_core_power_limit_count.attr,
thermal_attr_group.name);
- if (cpu_has(c, X86_FEATURE_PTS))
+ if (cpu_has(c, X86_FEATURE_PTS)) {
err = sysfs_add_file_to_group(&sys_dev->kobj,
&attr_package_throttle_count.attr,
thermal_attr_group.name);
@@ -224,6 +224,7 @@
err = sysfs_add_file_to_group(&sys_dev->kobj,
&attr_package_power_limit_count.attr,
thermal_attr_group.name);
+ }
return err;
}
diff --git a/arch/x86/kernel/cpu/perf_event_p4.c b/arch/x86/kernel/cpu/perf_event_p4.c
index b560db3..2490151 100644
--- a/arch/x86/kernel/cpu/perf_event_p4.c
+++ b/arch/x86/kernel/cpu/perf_event_p4.c
@@ -660,8 +660,12 @@
for (idx = 0; idx < x86_pmu.num_counters; idx++) {
int overflow;
- if (!test_bit(idx, cpuc->active_mask))
+ if (!test_bit(idx, cpuc->active_mask)) {
+ /* catch in-flight IRQs */
+ if (__test_and_clear_bit(idx, cpuc->running))
+ handled++;
continue;
+ }
event = cpuc->events[idx];
hwc = &event->hw;
diff --git a/arch/x86/kernel/module.c b/arch/x86/kernel/module.c
index e0bc186..1c355c5 100644
--- a/arch/x86/kernel/module.c
+++ b/arch/x86/kernel/module.c
@@ -239,11 +239,10 @@
apply_paravirt(pseg, pseg + para->sh_size);
}
- return module_bug_finalize(hdr, sechdrs, me);
+ return 0;
}
void module_arch_cleanup(struct module *mod)
{
alternatives_smp_module_del(mod);
- module_bug_cleanup(mod);
}
diff --git a/arch/x86/kvm/svm.c b/arch/x86/kvm/svm.c
index bc5b9b8..81ed28c 100644
--- a/arch/x86/kvm/svm.c
+++ b/arch/x86/kvm/svm.c
@@ -766,7 +766,6 @@
control->iopm_base_pa = iopm_base;
control->msrpm_base_pa = __pa(svm->msrpm);
- control->tsc_offset = 0;
control->int_ctl = V_INTR_MASKING_MASK;
init_seg(&save->es);
@@ -902,6 +901,7 @@
svm->vmcb_pa = page_to_pfn(page) << PAGE_SHIFT;
svm->asid_generation = 0;
init_vmcb(svm);
+ svm->vmcb->control.tsc_offset = 0-native_read_tsc();
err = fx_init(&svm->vcpu);
if (err)
diff --git a/arch/x86/mm/srat_64.c b/arch/x86/mm/srat_64.c
index f9897f7..9c0d0d3 100644
--- a/arch/x86/mm/srat_64.c
+++ b/arch/x86/mm/srat_64.c
@@ -420,9 +420,11 @@
return -1;
}
- for_each_node_mask(i, nodes_parsed)
- e820_register_active_regions(i, nodes[i].start >> PAGE_SHIFT,
- nodes[i].end >> PAGE_SHIFT);
+ for (i = 0; i < num_node_memblks; i++)
+ e820_register_active_regions(memblk_nodeid[i],
+ node_memblk_range[i].start >> PAGE_SHIFT,
+ node_memblk_range[i].end >> PAGE_SHIFT);
+
/* for out of order entries in SRAT */
sort_node_map();
if (!nodes_cover_memory(nodes)) {
diff --git a/arch/x86/oprofile/nmi_int.c b/arch/x86/oprofile/nmi_int.c
index 009b819..f1575c9 100644
--- a/arch/x86/oprofile/nmi_int.c
+++ b/arch/x86/oprofile/nmi_int.c
@@ -674,6 +674,7 @@
case 0x0f:
case 0x16:
case 0x17:
+ case 0x1d:
*cpu_type = "i386/core_2";
break;
case 0x1a:
diff --git a/arch/x86/xen/time.c b/arch/x86/xen/time.c
index 1a5353a..b2bb5aa3 100644
--- a/arch/x86/xen/time.c
+++ b/arch/x86/xen/time.c
@@ -489,8 +489,9 @@
__init void xen_hvm_init_time_ops(void)
{
/* vector callback is needed otherwise we cannot receive interrupts
- * on cpu > 0 */
- if (!xen_have_vector_callback && num_present_cpus() > 1)
+ * on cpu > 0 and at this point we don't know how many cpus are
+ * available */
+ if (!xen_have_vector_callback)
return;
if (!xen_feature(XENFEAT_hvm_safe_pvclock)) {
printk(KERN_INFO "Xen doesn't support pvclock on HVM,"
diff --git a/block/elevator.c b/block/elevator.c
index 205b09a..4e11559 100644
--- a/block/elevator.c
+++ b/block/elevator.c
@@ -938,6 +938,7 @@
}
}
kobject_uevent(&e->kobj, KOBJ_ADD);
+ e->registered = 1;
}
return error;
}
@@ -947,6 +948,7 @@
{
kobject_uevent(&e->kobj, KOBJ_REMOVE);
kobject_del(&e->kobj);
+ e->registered = 0;
}
void elv_unregister_queue(struct request_queue *q)
@@ -1042,11 +1044,13 @@
spin_unlock_irq(q->queue_lock);
- __elv_unregister_queue(old_elevator);
+ if (old_elevator->registered) {
+ __elv_unregister_queue(old_elevator);
- err = elv_register_queue(q);
- if (err)
- goto fail_register;
+ err = elv_register_queue(q);
+ if (err)
+ goto fail_register;
+ }
/*
* finally exit old elevator and turn off BYPASS.
diff --git a/drivers/acpi/blacklist.c b/drivers/acpi/blacklist.c
index f761960..af308d0 100644
--- a/drivers/acpi/blacklist.c
+++ b/drivers/acpi/blacklist.c
@@ -204,6 +204,23 @@
},
},
{
+ /*
+ * There have a NVIF method in MSI GX723 DSDT need call by Nvidia
+ * driver (e.g. nouveau) when user press brightness hotkey.
+ * Currently, nouveau driver didn't do the job and it causes there
+ * have a infinite while loop in DSDT when user press hotkey.
+ * We add MSI GX723's dmi information to this table for workaround
+ * this issue.
+ * Will remove MSI GX723 from the table after nouveau grows support.
+ */
+ .callback = dmi_disable_osi_vista,
+ .ident = "MSI GX723",
+ .matches = {
+ DMI_MATCH(DMI_SYS_VENDOR, "Micro-Star International"),
+ DMI_MATCH(DMI_PRODUCT_NAME, "GX723"),
+ },
+ },
+ {
.callback = dmi_disable_osi_vista,
.ident = "Sony VGN-NS10J_S",
.matches = {
diff --git a/drivers/acpi/processor_core.c b/drivers/acpi/processor_core.c
index b618f88..bec561c1 100644
--- a/drivers/acpi/processor_core.c
+++ b/drivers/acpi/processor_core.c
@@ -346,4 +346,5 @@
acpi_walk_namespace(ACPI_TYPE_PROCESSOR, ACPI_ROOT_OBJECT,
ACPI_UINT32_MAX,
early_init_pdc, NULL, NULL, NULL);
+ acpi_get_devices("ACPI0007", early_init_pdc, NULL, NULL);
}
diff --git a/drivers/atm/iphase.c b/drivers/atm/iphase.c
index ee9ddeb..8cb0347 100644
--- a/drivers/atm/iphase.c
+++ b/drivers/atm/iphase.c
@@ -3156,7 +3156,6 @@
{
struct atm_dev *dev;
IADEV *iadev;
- unsigned long flags;
int ret;
iadev = kzalloc(sizeof(*iadev), GFP_KERNEL);
@@ -3188,19 +3187,14 @@
ia_dev[iadev_count] = iadev;
_ia_dev[iadev_count] = dev;
iadev_count++;
- spin_lock_init(&iadev->misc_lock);
- /* First fixes first. I don't want to think about this now. */
- spin_lock_irqsave(&iadev->misc_lock, flags);
if (ia_init(dev) || ia_start(dev)) {
IF_INIT(printk("IA register failed!\n");)
iadev_count--;
ia_dev[iadev_count] = NULL;
_ia_dev[iadev_count] = NULL;
- spin_unlock_irqrestore(&iadev->misc_lock, flags);
ret = -EINVAL;
goto err_out_deregister_dev;
}
- spin_unlock_irqrestore(&iadev->misc_lock, flags);
IF_EVENT(printk("iadev_count = %d\n", iadev_count);)
iadev->next_board = ia_boards;
diff --git a/drivers/atm/iphase.h b/drivers/atm/iphase.h
index b2cd20f..077735e 100644
--- a/drivers/atm/iphase.h
+++ b/drivers/atm/iphase.h
@@ -1022,7 +1022,7 @@
struct dle_q rx_dle_q;
struct free_desc_q *rx_free_desc_qhead;
struct sk_buff_head rx_dma_q;
- spinlock_t rx_lock, misc_lock;
+ spinlock_t rx_lock;
struct atm_vcc **rx_open; /* list of all open VCs */
u16 num_rx_desc, rx_buf_sz, rxing;
u32 rx_pkt_ram, rx_tmp_cnt;
diff --git a/drivers/atm/solos-pci.c b/drivers/atm/solos-pci.c
index f916ddf63..f46138a 100644
--- a/drivers/atm/solos-pci.c
+++ b/drivers/atm/solos-pci.c
@@ -444,6 +444,7 @@
struct atm_dev *atmdev = container_of(dev, struct atm_dev, class_dev);
struct solos_card *card = atmdev->dev_data;
struct sk_buff *skb;
+ unsigned int len;
spin_lock(&card->cli_queue_lock);
skb = skb_dequeue(&card->cli_queue[SOLOS_CHAN(atmdev)]);
@@ -451,11 +452,12 @@
if(skb == NULL)
return sprintf(buf, "No data.\n");
- memcpy(buf, skb->data, skb->len);
- dev_dbg(&card->dev->dev, "len: %d\n", skb->len);
+ len = skb->len;
+ memcpy(buf, skb->data, len);
+ dev_dbg(&card->dev->dev, "len: %d\n", len);
kfree_skb(skb);
- return skb->len;
+ return len;
}
static int send_command(struct solos_card *card, int dev, const char *buf, size_t size)
diff --git a/drivers/block/ps3disk.c b/drivers/block/ps3disk.c
index e9da874..03688c2 100644
--- a/drivers/block/ps3disk.c
+++ b/drivers/block/ps3disk.c
@@ -113,7 +113,7 @@
memcpy(buf, dev->bounce_buf+offset, size);
offset += size;
flush_kernel_dcache_page(bvec->bv_page);
- bvec_kunmap_irq(bvec, &flags);
+ bvec_kunmap_irq(buf, &flags);
i++;
}
}
diff --git a/drivers/block/virtio_blk.c b/drivers/block/virtio_blk.c
index 2aafafc..1101e25 100644
--- a/drivers/block/virtio_blk.c
+++ b/drivers/block/virtio_blk.c
@@ -202,6 +202,7 @@
struct virtio_blk *vblk = disk->private_data;
struct request *req;
struct bio *bio;
+ int err;
bio = bio_map_kern(vblk->disk->queue, id_str, VIRTIO_BLK_ID_BYTES,
GFP_KERNEL);
@@ -215,7 +216,10 @@
}
req->cmd_type = REQ_TYPE_SPECIAL;
- return blk_execute_rq(vblk->disk->queue, vblk->disk, req, false);
+ err = blk_execute_rq(vblk->disk->queue, vblk->disk, req, false);
+ blk_put_request(req);
+
+ return err;
}
static int virtblk_locked_ioctl(struct block_device *bdev, fmode_t mode,
diff --git a/drivers/dma/ioat/dma_v2.c b/drivers/dma/ioat/dma_v2.c
index 216f9d3..effd140 100644
--- a/drivers/dma/ioat/dma_v2.c
+++ b/drivers/dma/ioat/dma_v2.c
@@ -879,7 +879,7 @@
dma->device_issue_pending = ioat2_issue_pending;
dma->device_alloc_chan_resources = ioat2_alloc_chan_resources;
dma->device_free_chan_resources = ioat2_free_chan_resources;
- dma->device_tx_status = ioat_tx_status;
+ dma->device_tx_status = ioat_dma_tx_status;
err = ioat_probe(device);
if (err)
diff --git a/drivers/firewire/ohci.c b/drivers/firewire/ohci.c
index 1b05896..9dcb17d 100644
--- a/drivers/firewire/ohci.c
+++ b/drivers/firewire/ohci.c
@@ -2840,7 +2840,7 @@
const struct pci_device_id *ent)
{
struct fw_ohci *ohci;
- u32 bus_options, max_receive, link_speed, version, link_enh;
+ u32 bus_options, max_receive, link_speed, version;
u64 guid;
int i, err, n_ir, n_it;
size_t size;
@@ -2894,23 +2894,6 @@
if (param_quirks)
ohci->quirks = param_quirks;
- /* TI OHCI-Lynx and compatible: set recommended configuration bits. */
- if (dev->vendor == PCI_VENDOR_ID_TI) {
- pci_read_config_dword(dev, PCI_CFG_TI_LinkEnh, &link_enh);
-
- /* adjust latency of ATx FIFO: use 1.7 KB threshold */
- link_enh &= ~TI_LinkEnh_atx_thresh_mask;
- link_enh |= TI_LinkEnh_atx_thresh_1_7K;
-
- /* use priority arbitration for asynchronous responses */
- link_enh |= TI_LinkEnh_enab_unfair;
-
- /* required for aPhyEnhanceEnable to work */
- link_enh |= TI_LinkEnh_enab_accel;
-
- pci_write_config_dword(dev, PCI_CFG_TI_LinkEnh, link_enh);
- }
-
ar_context_init(&ohci->ar_request_ctx, ohci,
OHCI1394_AsReqRcvContextControlSet);
diff --git a/drivers/firewire/ohci.h b/drivers/firewire/ohci.h
index 0e6c5a4..ef5e733 100644
--- a/drivers/firewire/ohci.h
+++ b/drivers/firewire/ohci.h
@@ -155,12 +155,4 @@
#define OHCI1394_phy_tcode 0xe
-/* TI extensions */
-
-#define PCI_CFG_TI_LinkEnh 0xf4
-#define TI_LinkEnh_enab_accel 0x00000002
-#define TI_LinkEnh_enab_unfair 0x00000080
-#define TI_LinkEnh_atx_thresh_mask 0x00003000
-#define TI_LinkEnh_atx_thresh_1_7K 0x00001000
-
#endif /* _FIREWIRE_OHCI_H */
diff --git a/drivers/gpu/drm/i915/i915_dma.c b/drivers/gpu/drm/i915/i915_dma.c
index 9d67b48..2dd2c93 100644
--- a/drivers/gpu/drm/i915/i915_dma.c
+++ b/drivers/gpu/drm/i915/i915_dma.c
@@ -1787,9 +1787,9 @@
}
}
- div_u64(diff, diff1);
+ diff = div_u64(diff, diff1);
ret = ((m * diff) + c);
- div_u64(ret, 10);
+ ret = div_u64(ret, 10);
dev_priv->last_count1 = total_count;
dev_priv->last_time1 = now;
@@ -1858,7 +1858,7 @@
/* More magic constants... */
diff = diff * 1181;
- div_u64(diff, diffms * 10);
+ diff = div_u64(diff, diffms * 10);
dev_priv->gfx_power = diff;
}
@@ -2231,6 +2231,9 @@
dev_priv->mchdev_lock = &mchdev_lock;
spin_unlock(&mchdev_lock);
+ /* XXX Prevent module unload due to memory corruption bugs. */
+ __module_get(THIS_MODULE);
+
return 0;
out_workqueue_free:
diff --git a/drivers/gpu/drm/i915/i915_gem.c b/drivers/gpu/drm/i915/i915_gem.c
index 2a0025f..90b1d67 100644
--- a/drivers/gpu/drm/i915/i915_gem.c
+++ b/drivers/gpu/drm/i915/i915_gem.c
@@ -469,14 +469,17 @@
return -ENOENT;
obj_priv = to_intel_bo(obj);
- /* Bounds check source.
- *
- * XXX: This could use review for overflow issues...
- */
- if (args->offset > obj->size || args->size > obj->size ||
- args->offset + args->size > obj->size) {
- drm_gem_object_unreference_unlocked(obj);
- return -EINVAL;
+ /* Bounds check source. */
+ if (args->offset > obj->size || args->size > obj->size - args->offset) {
+ ret = -EINVAL;
+ goto err;
+ }
+
+ if (!access_ok(VERIFY_WRITE,
+ (char __user *)(uintptr_t)args->data_ptr,
+ args->size)) {
+ ret = -EFAULT;
+ goto err;
}
if (i915_gem_object_needs_bit17_swizzle(obj)) {
@@ -488,8 +491,8 @@
file_priv);
}
+err:
drm_gem_object_unreference_unlocked(obj);
-
return ret;
}
@@ -578,8 +581,6 @@
user_data = (char __user *) (uintptr_t) args->data_ptr;
remain = args->size;
- if (!access_ok(VERIFY_READ, user_data, remain))
- return -EFAULT;
mutex_lock(&dev->struct_mutex);
@@ -932,14 +933,17 @@
return -ENOENT;
obj_priv = to_intel_bo(obj);
- /* Bounds check destination.
- *
- * XXX: This could use review for overflow issues...
- */
- if (args->offset > obj->size || args->size > obj->size ||
- args->offset + args->size > obj->size) {
- drm_gem_object_unreference_unlocked(obj);
- return -EINVAL;
+ /* Bounds check destination. */
+ if (args->offset > obj->size || args->size > obj->size - args->offset) {
+ ret = -EINVAL;
+ goto err;
+ }
+
+ if (!access_ok(VERIFY_READ,
+ (char __user *)(uintptr_t)args->data_ptr,
+ args->size)) {
+ ret = -EFAULT;
+ goto err;
}
/* We can only do the GTT pwrite on untiled buffers, as otherwise
@@ -973,8 +977,8 @@
DRM_INFO("pwrite failed %d\n", ret);
#endif
+err:
drm_gem_object_unreference_unlocked(obj);
-
return ret;
}
@@ -3256,6 +3260,8 @@
(int) reloc->offset,
reloc->read_domains,
reloc->write_domain);
+ drm_gem_object_unreference(target_obj);
+ i915_gem_object_unpin(obj);
return -EINVAL;
}
if (reloc->write_domain & I915_GEM_DOMAIN_CPU ||
diff --git a/drivers/gpu/drm/i915/i915_gem_evict.c b/drivers/gpu/drm/i915/i915_gem_evict.c
index e85246e..5c428fa 100644
--- a/drivers/gpu/drm/i915/i915_gem_evict.c
+++ b/drivers/gpu/drm/i915/i915_gem_evict.c
@@ -93,7 +93,7 @@
{
drm_i915_private_t *dev_priv = dev->dev_private;
struct list_head eviction_list, unwind_list;
- struct drm_i915_gem_object *obj_priv, *tmp_obj_priv;
+ struct drm_i915_gem_object *obj_priv;
struct list_head *render_iter, *bsd_iter;
int ret = 0;
@@ -175,39 +175,34 @@
return -ENOSPC;
found:
+ /* drm_mm doesn't allow any other other operations while
+ * scanning, therefore store to be evicted objects on a
+ * temporary list. */
INIT_LIST_HEAD(&eviction_list);
- list_for_each_entry_safe(obj_priv, tmp_obj_priv,
- &unwind_list, evict_list) {
+ while (!list_empty(&unwind_list)) {
+ obj_priv = list_first_entry(&unwind_list,
+ struct drm_i915_gem_object,
+ evict_list);
if (drm_mm_scan_remove_block(obj_priv->gtt_space)) {
- /* drm_mm doesn't allow any other other operations while
- * scanning, therefore store to be evicted objects on a
- * temporary list. */
list_move(&obj_priv->evict_list, &eviction_list);
- } else
- drm_gem_object_unreference(&obj_priv->base);
- }
-
- /* Unbinding will emit any required flushes */
- list_for_each_entry_safe(obj_priv, tmp_obj_priv,
- &eviction_list, evict_list) {
-#if WATCH_LRU
- DRM_INFO("%s: evicting %p\n", __func__, &obj_priv->base);
-#endif
- ret = i915_gem_object_unbind(&obj_priv->base);
- if (ret)
- return ret;
-
+ continue;
+ }
+ list_del(&obj_priv->evict_list);
drm_gem_object_unreference(&obj_priv->base);
}
- /* The just created free hole should be on the top of the free stack
- * maintained by drm_mm, so this BUG_ON actually executes in O(1).
- * Furthermore all accessed data has just recently been used, so it
- * should be really fast, too. */
- BUG_ON(!drm_mm_search_free(&dev_priv->mm.gtt_space, min_size,
- alignment, 0));
+ /* Unbinding will emit any required flushes */
+ while (!list_empty(&eviction_list)) {
+ obj_priv = list_first_entry(&eviction_list,
+ struct drm_i915_gem_object,
+ evict_list);
+ if (ret == 0)
+ ret = i915_gem_object_unbind(&obj_priv->base);
+ list_del(&obj_priv->evict_list);
+ drm_gem_object_unreference(&obj_priv->base);
+ }
- return 0;
+ return ret;
}
int
diff --git a/drivers/gpu/drm/i915/intel_display.c b/drivers/gpu/drm/i915/intel_display.c
index b5bf51a..9792285 100644
--- a/drivers/gpu/drm/i915/intel_display.c
+++ b/drivers/gpu/drm/i915/intel_display.c
@@ -1013,8 +1013,8 @@
DRM_DEBUG_KMS("vblank wait timed out\n");
}
-/**
- * intel_wait_for_vblank_off - wait for vblank after disabling a pipe
+/*
+ * intel_wait_for_pipe_off - wait for pipe to turn off
* @dev: drm device
* @pipe: pipe to wait for
*
@@ -1022,25 +1022,39 @@
* spinning on the vblank interrupt status bit, since we won't actually
* see an interrupt when the pipe is disabled.
*
- * So this function waits for the display line value to settle (it
- * usually ends up stopping at the start of the next frame).
+ * On Gen4 and above:
+ * wait for the pipe register state bit to turn off
+ *
+ * Otherwise:
+ * wait for the display line value to settle (it usually
+ * ends up stopping at the start of the next frame).
+ *
*/
-void intel_wait_for_vblank_off(struct drm_device *dev, int pipe)
+static void intel_wait_for_pipe_off(struct drm_device *dev, int pipe)
{
struct drm_i915_private *dev_priv = dev->dev_private;
- int pipedsl_reg = (pipe == 0 ? PIPEADSL : PIPEBDSL);
- unsigned long timeout = jiffies + msecs_to_jiffies(100);
- u32 last_line;
- /* Wait for the display line to settle */
- do {
- last_line = I915_READ(pipedsl_reg) & DSL_LINEMASK;
- mdelay(5);
- } while (((I915_READ(pipedsl_reg) & DSL_LINEMASK) != last_line) &&
- time_after(timeout, jiffies));
+ if (INTEL_INFO(dev)->gen >= 4) {
+ int pipeconf_reg = (pipe == 0 ? PIPEACONF : PIPEBCONF);
- if (time_after(jiffies, timeout))
- DRM_DEBUG_KMS("vblank wait timed out\n");
+ /* Wait for the Pipe State to go off */
+ if (wait_for((I915_READ(pipeconf_reg) & I965_PIPECONF_ACTIVE) == 0,
+ 100, 0))
+ DRM_DEBUG_KMS("pipe_off wait timed out\n");
+ } else {
+ u32 last_line;
+ int pipedsl_reg = (pipe == 0 ? PIPEADSL : PIPEBDSL);
+ unsigned long timeout = jiffies + msecs_to_jiffies(100);
+
+ /* Wait for the display line to settle */
+ do {
+ last_line = I915_READ(pipedsl_reg) & DSL_LINEMASK;
+ mdelay(5);
+ } while (((I915_READ(pipedsl_reg) & DSL_LINEMASK) != last_line) &&
+ time_after(timeout, jiffies));
+ if (time_after(jiffies, timeout))
+ DRM_DEBUG_KMS("pipe_off wait timed out\n");
+ }
}
/* Parameters have changed, update FBC info */
@@ -2328,13 +2342,13 @@
I915_READ(dspbase_reg);
}
- /* Wait for vblank for the disable to take effect */
- intel_wait_for_vblank_off(dev, pipe);
-
/* Don't disable pipe A or pipe A PLLs if needed */
if (pipeconf_reg == PIPEACONF &&
- (dev_priv->quirks & QUIRK_PIPEA_FORCE))
+ (dev_priv->quirks & QUIRK_PIPEA_FORCE)) {
+ /* Wait for vblank for the disable to take effect */
+ intel_wait_for_vblank(dev, pipe);
goto skip_pipe_off;
+ }
/* Next, disable display pipes */
temp = I915_READ(pipeconf_reg);
@@ -2343,8 +2357,8 @@
I915_READ(pipeconf_reg);
}
- /* Wait for vblank for the disable to take effect. */
- intel_wait_for_vblank_off(dev, pipe);
+ /* Wait for the pipe to turn off */
+ intel_wait_for_pipe_off(dev, pipe);
temp = I915_READ(dpll_reg);
if ((temp & DPLL_VCO_ENABLE) != 0) {
diff --git a/drivers/gpu/drm/i915/intel_dp.c b/drivers/gpu/drm/i915/intel_dp.c
index 1a51ee0..9ab8708 100644
--- a/drivers/gpu/drm/i915/intel_dp.c
+++ b/drivers/gpu/drm/i915/intel_dp.c
@@ -1138,18 +1138,14 @@
intel_dp_set_link_train(struct intel_dp *intel_dp,
uint32_t dp_reg_value,
uint8_t dp_train_pat,
- uint8_t train_set[4],
- bool first)
+ uint8_t train_set[4])
{
struct drm_device *dev = intel_dp->base.enc.dev;
struct drm_i915_private *dev_priv = dev->dev_private;
- struct intel_crtc *intel_crtc = to_intel_crtc(intel_dp->base.enc.crtc);
int ret;
I915_WRITE(intel_dp->output_reg, dp_reg_value);
POSTING_READ(intel_dp->output_reg);
- if (first)
- intel_wait_for_vblank(dev, intel_crtc->pipe);
intel_dp_aux_native_write_1(intel_dp,
DP_TRAINING_PATTERN_SET,
@@ -1174,10 +1170,15 @@
uint8_t voltage;
bool clock_recovery = false;
bool channel_eq = false;
- bool first = true;
int tries;
u32 reg;
uint32_t DP = intel_dp->DP;
+ struct intel_crtc *intel_crtc = to_intel_crtc(intel_dp->base.enc.crtc);
+
+ /* Enable output, wait for it to become active */
+ I915_WRITE(intel_dp->output_reg, intel_dp->DP);
+ POSTING_READ(intel_dp->output_reg);
+ intel_wait_for_vblank(dev, intel_crtc->pipe);
/* Write the link configuration data */
intel_dp_aux_native_write(intel_dp, DP_LINK_BW_SET,
@@ -1210,9 +1211,8 @@
reg = DP | DP_LINK_TRAIN_PAT_1;
if (!intel_dp_set_link_train(intel_dp, reg,
- DP_TRAINING_PATTERN_1, train_set, first))
+ DP_TRAINING_PATTERN_1, train_set))
break;
- first = false;
/* Set training pattern 1 */
udelay(100);
@@ -1266,8 +1266,7 @@
/* channel eq pattern */
if (!intel_dp_set_link_train(intel_dp, reg,
- DP_TRAINING_PATTERN_2, train_set,
- false))
+ DP_TRAINING_PATTERN_2, train_set))
break;
udelay(400);
diff --git a/drivers/gpu/drm/i915/intel_drv.h b/drivers/gpu/drm/i915/intel_drv.h
index ad312ca..8828b3a 100644
--- a/drivers/gpu/drm/i915/intel_drv.h
+++ b/drivers/gpu/drm/i915/intel_drv.h
@@ -229,7 +229,6 @@
struct drm_crtc *crtc);
int intel_get_pipe_from_crtc_id(struct drm_device *dev, void *data,
struct drm_file *file_priv);
-extern void intel_wait_for_vblank_off(struct drm_device *dev, int pipe);
extern void intel_wait_for_vblank(struct drm_device *dev, int pipe);
extern struct drm_crtc *intel_get_crtc_from_pipe(struct drm_device *dev, int pipe);
extern struct drm_crtc *intel_get_load_detect_pipe(struct intel_encoder *intel_encoder,
diff --git a/drivers/gpu/drm/i915/intel_fb.c b/drivers/gpu/drm/i915/intel_fb.c
index 56ad9df..b61966c 100644
--- a/drivers/gpu/drm/i915/intel_fb.c
+++ b/drivers/gpu/drm/i915/intel_fb.c
@@ -238,8 +238,8 @@
drm_framebuffer_cleanup(&ifb->base);
if (ifb->obj) {
- drm_gem_object_handle_unreference(ifb->obj);
drm_gem_object_unreference(ifb->obj);
+ ifb->obj = NULL;
}
return 0;
diff --git a/drivers/gpu/drm/nouveau/nouveau_fbcon.c b/drivers/gpu/drm/nouveau/nouveau_fbcon.c
index d204771..dbd30b2 100644
--- a/drivers/gpu/drm/nouveau/nouveau_fbcon.c
+++ b/drivers/gpu/drm/nouveau/nouveau_fbcon.c
@@ -352,7 +352,6 @@
if (nouveau_fb->nvbo) {
nouveau_bo_unmap(nouveau_fb->nvbo);
- drm_gem_object_handle_unreference_unlocked(nouveau_fb->nvbo->gem);
drm_gem_object_unreference_unlocked(nouveau_fb->nvbo->gem);
nouveau_fb->nvbo = NULL;
}
diff --git a/drivers/gpu/drm/nouveau/nouveau_notifier.c b/drivers/gpu/drm/nouveau/nouveau_notifier.c
index 3c9964a..3ec181f 100644
--- a/drivers/gpu/drm/nouveau/nouveau_notifier.c
+++ b/drivers/gpu/drm/nouveau/nouveau_notifier.c
@@ -79,7 +79,6 @@
mutex_lock(&dev->struct_mutex);
nouveau_bo_unpin(chan->notifier_bo);
mutex_unlock(&dev->struct_mutex);
- drm_gem_object_handle_unreference_unlocked(chan->notifier_bo->gem);
drm_gem_object_unreference_unlocked(chan->notifier_bo->gem);
drm_mm_takedown(&chan->notifier_heap);
}
diff --git a/drivers/gpu/drm/radeon/evergreen.c b/drivers/gpu/drm/radeon/evergreen.c
index 79082d4..2f93d46 100644
--- a/drivers/gpu/drm/radeon/evergreen.c
+++ b/drivers/gpu/drm/radeon/evergreen.c
@@ -1137,7 +1137,7 @@
WREG32(RCU_IND_INDEX, 0x203);
efuse_straps_3 = RREG32(RCU_IND_DATA);
- efuse_box_bit_127_124 = (u8)(efuse_straps_3 & 0xF0000000) >> 28;
+ efuse_box_bit_127_124 = (u8)((efuse_straps_3 & 0xF0000000) >> 28);
switch(efuse_box_bit_127_124) {
case 0x0:
@@ -1407,6 +1407,7 @@
rdev->mc.mc_vram_size = RREG32(CONFIG_MEMSIZE) * 1024 * 1024;
rdev->mc.real_vram_size = RREG32(CONFIG_MEMSIZE) * 1024 * 1024;
rdev->mc.visible_vram_size = rdev->mc.aper_size;
+ rdev->mc.active_vram_size = rdev->mc.visible_vram_size;
r600_vram_gtt_location(rdev, &rdev->mc);
radeon_update_bandwidth_info(rdev);
@@ -1520,7 +1521,7 @@
{
u32 tmp;
- WREG32(CP_INT_CNTL, 0);
+ WREG32(CP_INT_CNTL, CNTX_BUSY_INT_ENABLE | CNTX_EMPTY_INT_ENABLE);
WREG32(GRBM_INT_CNTL, 0);
WREG32(INT_MASK + EVERGREEN_CRTC0_REGISTER_OFFSET, 0);
WREG32(INT_MASK + EVERGREEN_CRTC1_REGISTER_OFFSET, 0);
diff --git a/drivers/gpu/drm/radeon/r100.c b/drivers/gpu/drm/radeon/r100.c
index e151f16..e594223 100644
--- a/drivers/gpu/drm/radeon/r100.c
+++ b/drivers/gpu/drm/radeon/r100.c
@@ -1030,6 +1030,7 @@
return r;
}
rdev->cp.ready = true;
+ rdev->mc.active_vram_size = rdev->mc.real_vram_size;
return 0;
}
@@ -1047,6 +1048,7 @@
void r100_cp_disable(struct radeon_device *rdev)
{
/* Disable ring */
+ rdev->mc.active_vram_size = rdev->mc.visible_vram_size;
rdev->cp.ready = false;
WREG32(RADEON_CP_CSQ_MODE, 0);
WREG32(RADEON_CP_CSQ_CNTL, 0);
@@ -2295,6 +2297,7 @@
/* FIXME we don't use the second aperture yet when we could use it */
if (rdev->mc.visible_vram_size > rdev->mc.aper_size)
rdev->mc.visible_vram_size = rdev->mc.aper_size;
+ rdev->mc.active_vram_size = rdev->mc.visible_vram_size;
config_aper_size = RREG32(RADEON_CONFIG_APER_SIZE);
if (rdev->flags & RADEON_IS_IGP) {
uint32_t tom;
diff --git a/drivers/gpu/drm/radeon/r600.c b/drivers/gpu/drm/radeon/r600.c
index 7a04959..7b65e4ef 100644
--- a/drivers/gpu/drm/radeon/r600.c
+++ b/drivers/gpu/drm/radeon/r600.c
@@ -1248,6 +1248,7 @@
rdev->mc.mc_vram_size = RREG32(CONFIG_MEMSIZE);
rdev->mc.real_vram_size = RREG32(CONFIG_MEMSIZE);
rdev->mc.visible_vram_size = rdev->mc.aper_size;
+ rdev->mc.active_vram_size = rdev->mc.visible_vram_size;
r600_vram_gtt_location(rdev, &rdev->mc);
if (rdev->flags & RADEON_IS_IGP) {
@@ -1917,6 +1918,7 @@
*/
void r600_cp_stop(struct radeon_device *rdev)
{
+ rdev->mc.active_vram_size = rdev->mc.visible_vram_size;
WREG32(R_0086D8_CP_ME_CNTL, S_0086D8_CP_ME_HALT(1));
}
@@ -2910,7 +2912,7 @@
{
u32 tmp;
- WREG32(CP_INT_CNTL, 0);
+ WREG32(CP_INT_CNTL, CNTX_BUSY_INT_ENABLE | CNTX_EMPTY_INT_ENABLE);
WREG32(GRBM_INT_CNTL, 0);
WREG32(DxMODE_INT_MASK, 0);
if (ASIC_IS_DCE3(rdev)) {
diff --git a/drivers/gpu/drm/radeon/r600_blit_kms.c b/drivers/gpu/drm/radeon/r600_blit_kms.c
index 9ceb2a1..3473c00 100644
--- a/drivers/gpu/drm/radeon/r600_blit_kms.c
+++ b/drivers/gpu/drm/radeon/r600_blit_kms.c
@@ -532,6 +532,7 @@
memcpy(ptr + rdev->r600_blit.ps_offset, r6xx_ps, r6xx_ps_size * 4);
radeon_bo_kunmap(rdev->r600_blit.shader_obj);
radeon_bo_unreserve(rdev->r600_blit.shader_obj);
+ rdev->mc.active_vram_size = rdev->mc.real_vram_size;
return 0;
}
@@ -539,6 +540,7 @@
{
int r;
+ rdev->mc.active_vram_size = rdev->mc.visible_vram_size;
if (rdev->r600_blit.shader_obj == NULL)
return;
/* If we can't reserve the bo, unref should be enough to destroy
diff --git a/drivers/gpu/drm/radeon/radeon.h b/drivers/gpu/drm/radeon/radeon.h
index a168d64..9ff38c9 100644
--- a/drivers/gpu/drm/radeon/radeon.h
+++ b/drivers/gpu/drm/radeon/radeon.h
@@ -344,6 +344,7 @@
* about vram size near mc fb location */
u64 mc_vram_size;
u64 visible_vram_size;
+ u64 active_vram_size;
u64 gtt_size;
u64 gtt_start;
u64 gtt_end;
diff --git a/drivers/gpu/drm/radeon/radeon_atombios.c b/drivers/gpu/drm/radeon/radeon_atombios.c
index 68932ba..8e43dda 100644
--- a/drivers/gpu/drm/radeon/radeon_atombios.c
+++ b/drivers/gpu/drm/radeon/radeon_atombios.c
@@ -1558,39 +1558,39 @@
switch (tv_info->ucTV_BootUpDefaultStandard) {
case ATOM_TV_NTSC:
tv_std = TV_STD_NTSC;
- DRM_INFO("Default TV standard: NTSC\n");
+ DRM_DEBUG_KMS("Default TV standard: NTSC\n");
break;
case ATOM_TV_NTSCJ:
tv_std = TV_STD_NTSC_J;
- DRM_INFO("Default TV standard: NTSC-J\n");
+ DRM_DEBUG_KMS("Default TV standard: NTSC-J\n");
break;
case ATOM_TV_PAL:
tv_std = TV_STD_PAL;
- DRM_INFO("Default TV standard: PAL\n");
+ DRM_DEBUG_KMS("Default TV standard: PAL\n");
break;
case ATOM_TV_PALM:
tv_std = TV_STD_PAL_M;
- DRM_INFO("Default TV standard: PAL-M\n");
+ DRM_DEBUG_KMS("Default TV standard: PAL-M\n");
break;
case ATOM_TV_PALN:
tv_std = TV_STD_PAL_N;
- DRM_INFO("Default TV standard: PAL-N\n");
+ DRM_DEBUG_KMS("Default TV standard: PAL-N\n");
break;
case ATOM_TV_PALCN:
tv_std = TV_STD_PAL_CN;
- DRM_INFO("Default TV standard: PAL-CN\n");
+ DRM_DEBUG_KMS("Default TV standard: PAL-CN\n");
break;
case ATOM_TV_PAL60:
tv_std = TV_STD_PAL_60;
- DRM_INFO("Default TV standard: PAL-60\n");
+ DRM_DEBUG_KMS("Default TV standard: PAL-60\n");
break;
case ATOM_TV_SECAM:
tv_std = TV_STD_SECAM;
- DRM_INFO("Default TV standard: SECAM\n");
+ DRM_DEBUG_KMS("Default TV standard: SECAM\n");
break;
default:
tv_std = TV_STD_NTSC;
- DRM_INFO("Unknown TV standard; defaulting to NTSC\n");
+ DRM_DEBUG_KMS("Unknown TV standard; defaulting to NTSC\n");
break;
}
}
diff --git a/drivers/gpu/drm/radeon/radeon_combios.c b/drivers/gpu/drm/radeon/radeon_combios.c
index a04b7a6..7b7ea26 100644
--- a/drivers/gpu/drm/radeon/radeon_combios.c
+++ b/drivers/gpu/drm/radeon/radeon_combios.c
@@ -913,47 +913,47 @@
switch (RBIOS8(tv_info + 7) & 0xf) {
case 1:
tv_std = TV_STD_NTSC;
- DRM_INFO("Default TV standard: NTSC\n");
+ DRM_DEBUG_KMS("Default TV standard: NTSC\n");
break;
case 2:
tv_std = TV_STD_PAL;
- DRM_INFO("Default TV standard: PAL\n");
+ DRM_DEBUG_KMS("Default TV standard: PAL\n");
break;
case 3:
tv_std = TV_STD_PAL_M;
- DRM_INFO("Default TV standard: PAL-M\n");
+ DRM_DEBUG_KMS("Default TV standard: PAL-M\n");
break;
case 4:
tv_std = TV_STD_PAL_60;
- DRM_INFO("Default TV standard: PAL-60\n");
+ DRM_DEBUG_KMS("Default TV standard: PAL-60\n");
break;
case 5:
tv_std = TV_STD_NTSC_J;
- DRM_INFO("Default TV standard: NTSC-J\n");
+ DRM_DEBUG_KMS("Default TV standard: NTSC-J\n");
break;
case 6:
tv_std = TV_STD_SCART_PAL;
- DRM_INFO("Default TV standard: SCART-PAL\n");
+ DRM_DEBUG_KMS("Default TV standard: SCART-PAL\n");
break;
default:
tv_std = TV_STD_NTSC;
- DRM_INFO
+ DRM_DEBUG_KMS
("Unknown TV standard; defaulting to NTSC\n");
break;
}
switch ((RBIOS8(tv_info + 9) >> 2) & 0x3) {
case 0:
- DRM_INFO("29.498928713 MHz TV ref clk\n");
+ DRM_DEBUG_KMS("29.498928713 MHz TV ref clk\n");
break;
case 1:
- DRM_INFO("28.636360000 MHz TV ref clk\n");
+ DRM_DEBUG_KMS("28.636360000 MHz TV ref clk\n");
break;
case 2:
- DRM_INFO("14.318180000 MHz TV ref clk\n");
+ DRM_DEBUG_KMS("14.318180000 MHz TV ref clk\n");
break;
case 3:
- DRM_INFO("27.000000000 MHz TV ref clk\n");
+ DRM_DEBUG_KMS("27.000000000 MHz TV ref clk\n");
break;
default:
break;
@@ -1324,7 +1324,7 @@
if (tmds_info) {
ver = RBIOS8(tmds_info);
- DRM_INFO("DFP table revision: %d\n", ver);
+ DRM_DEBUG_KMS("DFP table revision: %d\n", ver);
if (ver == 3) {
n = RBIOS8(tmds_info + 5) + 1;
if (n > 4)
@@ -1408,7 +1408,7 @@
offset = combios_get_table_offset(dev, COMBIOS_EXT_TMDS_INFO_TABLE);
if (offset) {
ver = RBIOS8(offset);
- DRM_INFO("External TMDS Table revision: %d\n", ver);
+ DRM_DEBUG_KMS("External TMDS Table revision: %d\n", ver);
tmds->slave_addr = RBIOS8(offset + 4 + 2);
tmds->slave_addr >>= 1; /* 7 bit addressing */
gpio = RBIOS8(offset + 4 + 3);
diff --git a/drivers/gpu/drm/radeon/radeon_fb.c b/drivers/gpu/drm/radeon/radeon_fb.c
index 9cdf6a3..40b0c08 100644
--- a/drivers/gpu/drm/radeon/radeon_fb.c
+++ b/drivers/gpu/drm/radeon/radeon_fb.c
@@ -97,7 +97,6 @@
radeon_bo_unpin(rbo);
radeon_bo_unreserve(rbo);
}
- drm_gem_object_handle_unreference(gobj);
drm_gem_object_unreference_unlocked(gobj);
}
diff --git a/drivers/gpu/drm/radeon/radeon_object.c b/drivers/gpu/drm/radeon/radeon_object.c
index 0afd1e6..b3b5306 100644
--- a/drivers/gpu/drm/radeon/radeon_object.c
+++ b/drivers/gpu/drm/radeon/radeon_object.c
@@ -69,7 +69,7 @@
u32 c = 0;
rbo->placement.fpfn = 0;
- rbo->placement.lpfn = 0;
+ rbo->placement.lpfn = rbo->rdev->mc.active_vram_size >> PAGE_SHIFT;
rbo->placement.placement = rbo->placements;
rbo->placement.busy_placement = rbo->placements;
if (domain & RADEON_GEM_DOMAIN_VRAM)
diff --git a/drivers/gpu/drm/radeon/radeon_object.h b/drivers/gpu/drm/radeon/radeon_object.h
index 353998d..3481bc7 100644
--- a/drivers/gpu/drm/radeon/radeon_object.h
+++ b/drivers/gpu/drm/radeon/radeon_object.h
@@ -124,11 +124,8 @@
int r;
r = ttm_bo_reserve(&bo->tbo, true, no_wait, false, 0);
- if (unlikely(r != 0)) {
- if (r != -ERESTARTSYS)
- dev_err(bo->rdev->dev, "%p reserve failed for wait\n", bo);
+ if (unlikely(r != 0))
return r;
- }
spin_lock(&bo->tbo.lock);
if (mem_type)
*mem_type = bo->tbo.mem.mem_type;
diff --git a/drivers/gpu/drm/radeon/rs600.c b/drivers/gpu/drm/radeon/rs600.c
index cc05b23..51d5f7b 100644
--- a/drivers/gpu/drm/radeon/rs600.c
+++ b/drivers/gpu/drm/radeon/rs600.c
@@ -693,6 +693,7 @@
rdev->mc.real_vram_size = RREG32(RADEON_CONFIG_MEMSIZE);
rdev->mc.mc_vram_size = rdev->mc.real_vram_size;
rdev->mc.visible_vram_size = rdev->mc.aper_size;
+ rdev->mc.active_vram_size = rdev->mc.visible_vram_size;
rdev->mc.igp_sideport_enabled = radeon_atombios_sideport_present(rdev);
base = RREG32_MC(R_000004_MC_FB_LOCATION);
base = G_000004_MC_FB_START(base) << 16;
diff --git a/drivers/gpu/drm/radeon/rs690.c b/drivers/gpu/drm/radeon/rs690.c
index 3e3f757..4dc2a87 100644
--- a/drivers/gpu/drm/radeon/rs690.c
+++ b/drivers/gpu/drm/radeon/rs690.c
@@ -157,6 +157,7 @@
rdev->mc.aper_base = pci_resource_start(rdev->pdev, 0);
rdev->mc.aper_size = pci_resource_len(rdev->pdev, 0);
rdev->mc.visible_vram_size = rdev->mc.aper_size;
+ rdev->mc.active_vram_size = rdev->mc.visible_vram_size;
base = RREG32_MC(R_000100_MCCFG_FB_LOCATION);
base = G_000100_MC_FB_START(base) << 16;
rdev->mc.igp_sideport_enabled = radeon_atombios_sideport_present(rdev);
diff --git a/drivers/gpu/drm/radeon/rv770.c b/drivers/gpu/drm/radeon/rv770.c
index bfa59db..9490da7 100644
--- a/drivers/gpu/drm/radeon/rv770.c
+++ b/drivers/gpu/drm/radeon/rv770.c
@@ -267,6 +267,7 @@
*/
void r700_cp_stop(struct radeon_device *rdev)
{
+ rdev->mc.active_vram_size = rdev->mc.visible_vram_size;
WREG32(CP_ME_CNTL, (CP_ME_HALT | CP_PFP_HALT));
}
@@ -992,6 +993,7 @@
rdev->mc.mc_vram_size = RREG32(CONFIG_MEMSIZE);
rdev->mc.real_vram_size = RREG32(CONFIG_MEMSIZE);
rdev->mc.visible_vram_size = rdev->mc.aper_size;
+ rdev->mc.active_vram_size = rdev->mc.visible_vram_size;
r600_vram_gtt_location(rdev, &rdev->mc);
radeon_update_bandwidth_info(rdev);
diff --git a/drivers/gpu/drm/ttm/ttm_bo.c b/drivers/gpu/drm/ttm/ttm_bo.c
index cb4cf7e..db809e0 100644
--- a/drivers/gpu/drm/ttm/ttm_bo.c
+++ b/drivers/gpu/drm/ttm/ttm_bo.c
@@ -442,6 +442,43 @@
}
/**
+ * Call bo::reserved and with the lru lock held.
+ * Will release GPU memory type usage on destruction.
+ * This is the place to put in driver specific hooks.
+ * Will release the bo::reserved lock and the
+ * lru lock on exit.
+ */
+
+static void ttm_bo_cleanup_memtype_use(struct ttm_buffer_object *bo)
+{
+ struct ttm_bo_global *glob = bo->glob;
+
+ if (bo->ttm) {
+
+ /**
+ * Release the lru_lock, since we don't want to have
+ * an atomic requirement on ttm_tt[unbind|destroy].
+ */
+
+ spin_unlock(&glob->lru_lock);
+ ttm_tt_unbind(bo->ttm);
+ ttm_tt_destroy(bo->ttm);
+ bo->ttm = NULL;
+ spin_lock(&glob->lru_lock);
+ }
+
+ if (bo->mem.mm_node) {
+ drm_mm_put_block(bo->mem.mm_node);
+ bo->mem.mm_node = NULL;
+ }
+
+ atomic_set(&bo->reserved, 0);
+ wake_up_all(&bo->event_queue);
+ spin_unlock(&glob->lru_lock);
+}
+
+
+/**
* If bo idle, remove from delayed- and lru lists, and unref.
* If not idle, and already on delayed list, do nothing.
* If not idle, and not on delayed list, put on delayed list,
@@ -456,6 +493,7 @@
int ret;
spin_lock(&bo->lock);
+retry:
(void) ttm_bo_wait(bo, false, false, !remove_all);
if (!bo->sync_obj) {
@@ -464,31 +502,52 @@
spin_unlock(&bo->lock);
spin_lock(&glob->lru_lock);
- put_count = ttm_bo_del_from_lru(bo);
+ ret = ttm_bo_reserve_locked(bo, false, !remove_all, false, 0);
- ret = ttm_bo_reserve_locked(bo, false, false, false, 0);
- BUG_ON(ret);
- if (bo->ttm)
- ttm_tt_unbind(bo->ttm);
+ /**
+ * Someone else has the object reserved. Bail and retry.
+ */
+
+ if (unlikely(ret == -EBUSY)) {
+ spin_unlock(&glob->lru_lock);
+ spin_lock(&bo->lock);
+ goto requeue;
+ }
+
+ /**
+ * We can re-check for sync object without taking
+ * the bo::lock since setting the sync object requires
+ * also bo::reserved. A busy object at this point may
+ * be caused by another thread starting an accelerated
+ * eviction.
+ */
+
+ if (unlikely(bo->sync_obj)) {
+ atomic_set(&bo->reserved, 0);
+ wake_up_all(&bo->event_queue);
+ spin_unlock(&glob->lru_lock);
+ spin_lock(&bo->lock);
+ if (remove_all)
+ goto retry;
+ else
+ goto requeue;
+ }
+
+ put_count = ttm_bo_del_from_lru(bo);
if (!list_empty(&bo->ddestroy)) {
list_del_init(&bo->ddestroy);
++put_count;
}
- if (bo->mem.mm_node) {
- drm_mm_put_block(bo->mem.mm_node);
- bo->mem.mm_node = NULL;
- }
- spin_unlock(&glob->lru_lock);
- atomic_set(&bo->reserved, 0);
+ ttm_bo_cleanup_memtype_use(bo);
while (put_count--)
kref_put(&bo->list_kref, ttm_bo_ref_bug);
return 0;
}
-
+requeue:
spin_lock(&glob->lru_lock);
if (list_empty(&bo->ddestroy)) {
void *sync_obj = bo->sync_obj;
diff --git a/drivers/hid/hid-cando.c b/drivers/hid/hid-cando.c
index 4267a6f..5925bdc 100644
--- a/drivers/hid/hid-cando.c
+++ b/drivers/hid/hid-cando.c
@@ -237,6 +237,8 @@
USB_DEVICE_ID_CANDO_MULTI_TOUCH) },
{ HID_USB_DEVICE(USB_VENDOR_ID_CANDO,
USB_DEVICE_ID_CANDO_MULTI_TOUCH_11_6) },
+ { HID_USB_DEVICE(USB_VENDOR_ID_CANDO,
+ USB_DEVICE_ID_CANDO_MULTI_TOUCH_15_6) },
{ }
};
MODULE_DEVICE_TABLE(hid, cando_devices);
diff --git a/drivers/hid/hid-core.c b/drivers/hid/hid-core.c
index 3f72924..a0dea3d 100644
--- a/drivers/hid/hid-core.c
+++ b/drivers/hid/hid-core.c
@@ -1292,6 +1292,7 @@
{ HID_USB_DEVICE(USB_VENDOR_ID_BTC, USB_DEVICE_ID_BTC_EMPREX_REMOTE_2) },
{ HID_USB_DEVICE(USB_VENDOR_ID_CANDO, USB_DEVICE_ID_CANDO_MULTI_TOUCH) },
{ HID_USB_DEVICE(USB_VENDOR_ID_CANDO, USB_DEVICE_ID_CANDO_MULTI_TOUCH_11_6) },
+ { HID_USB_DEVICE(USB_VENDOR_ID_CANDO, USB_DEVICE_ID_CANDO_MULTI_TOUCH_15_6) },
{ HID_USB_DEVICE(USB_VENDOR_ID_CHERRY, USB_DEVICE_ID_CHERRY_CYMOTION) },
{ HID_USB_DEVICE(USB_VENDOR_ID_CHERRY, USB_DEVICE_ID_CHERRY_CYMOTION_SOLAR) },
{ HID_USB_DEVICE(USB_VENDOR_ID_CHICONY, USB_DEVICE_ID_CHICONY_TACTICAL_PAD) },
diff --git a/drivers/hid/hid-ids.h b/drivers/hid/hid-ids.h
index 765a4f5..c5ae5f1 100644
--- a/drivers/hid/hid-ids.h
+++ b/drivers/hid/hid-ids.h
@@ -134,6 +134,7 @@
#define USB_VENDOR_ID_CANDO 0x2087
#define USB_DEVICE_ID_CANDO_MULTI_TOUCH 0x0a01
#define USB_DEVICE_ID_CANDO_MULTI_TOUCH_11_6 0x0b03
+#define USB_DEVICE_ID_CANDO_MULTI_TOUCH_15_6 0x0f01
#define USB_VENDOR_ID_CH 0x068e
#define USB_DEVICE_ID_CH_PRO_PEDALS 0x00f2
@@ -503,6 +504,7 @@
#define USB_VENDOR_ID_TURBOX 0x062a
#define USB_DEVICE_ID_TURBOX_KEYBOARD 0x0201
+#define USB_DEVICE_ID_TURBOX_TOUCHSCREEN_MOSART 0x7100
#define USB_VENDOR_ID_TWINHAN 0x6253
#define USB_DEVICE_ID_TWINHAN_IR_REMOTE 0x0100
diff --git a/drivers/hid/hidraw.c b/drivers/hid/hidraw.c
index 47d70c5..a3866b5 100644
--- a/drivers/hid/hidraw.c
+++ b/drivers/hid/hidraw.c
@@ -109,6 +109,12 @@
int ret = 0;
mutex_lock(&minors_lock);
+
+ if (!hidraw_table[minor]) {
+ ret = -ENODEV;
+ goto out;
+ }
+
dev = hidraw_table[minor]->hid;
if (!dev->hid_output_raw_report) {
@@ -244,6 +250,10 @@
mutex_lock(&minors_lock);
dev = hidraw_table[minor];
+ if (!dev) {
+ ret = -ENODEV;
+ goto out;
+ }
switch (cmd) {
case HIDIOCGRDESCSIZE:
@@ -317,6 +327,7 @@
ret = -ENOTTY;
}
+out:
mutex_unlock(&minors_lock);
return ret;
}
diff --git a/drivers/hid/usbhid/hid-quirks.c b/drivers/hid/usbhid/hid-quirks.c
index 70da318..f0260c6 100644
--- a/drivers/hid/usbhid/hid-quirks.c
+++ b/drivers/hid/usbhid/hid-quirks.c
@@ -36,6 +36,7 @@
{ USB_VENDOR_ID_DWAV, USB_DEVICE_ID_EGALAX_TOUCHCONTROLLER, HID_QUIRK_MULTI_INPUT | HID_QUIRK_NOGET },
{ USB_VENDOR_ID_DWAV, USB_DEVICE_ID_DWAV_EGALAX_MULTITOUCH, HID_QUIRK_MULTI_INPUT },
{ USB_VENDOR_ID_MOJO, USB_DEVICE_ID_RETRO_ADAPTER, HID_QUIRK_MULTI_INPUT },
+ { USB_VENDOR_ID_TURBOX, USB_DEVICE_ID_TURBOX_TOUCHSCREEN_MOSART, HID_QUIRK_MULTI_INPUT },
{ USB_VENDOR_ID_HAPP, USB_DEVICE_ID_UGCI_DRIVING, HID_QUIRK_BADPAD | HID_QUIRK_MULTI_INPUT },
{ USB_VENDOR_ID_HAPP, USB_DEVICE_ID_UGCI_FLYING, HID_QUIRK_BADPAD | HID_QUIRK_MULTI_INPUT },
{ USB_VENDOR_ID_HAPP, USB_DEVICE_ID_UGCI_FIGHTING, HID_QUIRK_BADPAD | HID_QUIRK_MULTI_INPUT },
diff --git a/drivers/hwmon/f71882fg.c b/drivers/hwmon/f71882fg.c
index 537841e..75afb3b 100644
--- a/drivers/hwmon/f71882fg.c
+++ b/drivers/hwmon/f71882fg.c
@@ -111,7 +111,7 @@
/* Super-I/O Function prototypes */
static inline int superio_inb(int base, int reg);
static inline int superio_inw(int base, int reg);
-static inline void superio_enter(int base);
+static inline int superio_enter(int base);
static inline void superio_select(int base, int ld);
static inline void superio_exit(int base);
@@ -861,11 +861,20 @@
return val;
}
-static inline void superio_enter(int base)
+static inline int superio_enter(int base)
{
+ /* Don't step on other drivers' I/O space by accident */
+ if (!request_muxed_region(base, 2, DRVNAME)) {
+ printk(KERN_ERR DRVNAME ": I/O address 0x%04x already in use\n",
+ base);
+ return -EBUSY;
+ }
+
/* according to the datasheet the key must be send twice! */
outb(SIO_UNLOCK_KEY, base);
outb(SIO_UNLOCK_KEY, base);
+
+ return 0;
}
static inline void superio_select(int base, int ld)
@@ -877,6 +886,7 @@
static inline void superio_exit(int base)
{
outb(SIO_LOCK_KEY, base);
+ release_region(base, 2);
}
static inline int fan_from_reg(u16 reg)
@@ -2175,21 +2185,15 @@
static int __init f71882fg_find(int sioaddr, unsigned short *address,
struct f71882fg_sio_data *sio_data)
{
- int err = -ENODEV;
u16 devid;
-
- /* Don't step on other drivers' I/O space by accident */
- if (!request_region(sioaddr, 2, DRVNAME)) {
- printk(KERN_ERR DRVNAME ": I/O address 0x%04x already in use\n",
- (int)sioaddr);
- return -EBUSY;
- }
-
- superio_enter(sioaddr);
+ int err = superio_enter(sioaddr);
+ if (err)
+ return err;
devid = superio_inw(sioaddr, SIO_REG_MANID);
if (devid != SIO_FINTEK_ID) {
pr_debug(DRVNAME ": Not a Fintek device\n");
+ err = -ENODEV;
goto exit;
}
@@ -2213,6 +2217,7 @@
default:
printk(KERN_INFO DRVNAME ": Unsupported Fintek device: %04x\n",
(unsigned int)devid);
+ err = -ENODEV;
goto exit;
}
@@ -2223,12 +2228,14 @@
if (!(superio_inb(sioaddr, SIO_REG_ENABLE) & 0x01)) {
printk(KERN_WARNING DRVNAME ": Device not activated\n");
+ err = -ENODEV;
goto exit;
}
*address = superio_inw(sioaddr, SIO_REG_ADDR);
if (*address == 0) {
printk(KERN_WARNING DRVNAME ": Base address not set\n");
+ err = -ENODEV;
goto exit;
}
*address &= ~(REGION_LENGTH - 1); /* Ignore 3 LSB */
@@ -2239,7 +2246,6 @@
(int)superio_inb(sioaddr, SIO_REG_DEVREV));
exit:
superio_exit(sioaddr);
- release_region(sioaddr, 2);
return err;
}
diff --git a/drivers/i2c/busses/i2c-cpm.c b/drivers/i2c/busses/i2c-cpm.c
index f7bd261..f2de3be 100644
--- a/drivers/i2c/busses/i2c-cpm.c
+++ b/drivers/i2c/busses/i2c-cpm.c
@@ -677,6 +677,11 @@
dev_dbg(&ofdev->dev, "hw routines for %s registered.\n",
cpm->adap.name);
+ /*
+ * register OF I2C devices
+ */
+ of_i2c_register_devices(&cpm->adap);
+
return 0;
out_shut:
cpm_i2c_shutdown(cpm);
diff --git a/drivers/i2c/busses/i2c-davinci.c b/drivers/i2c/busses/i2c-davinci.c
index b8feac5..5795c83 100644
--- a/drivers/i2c/busses/i2c-davinci.c
+++ b/drivers/i2c/busses/i2c-davinci.c
@@ -331,21 +331,16 @@
INIT_COMPLETION(dev->cmd_complete);
dev->cmd_err = 0;
- /* Take I2C out of reset, configure it as master and set the
- * start bit */
- flag = DAVINCI_I2C_MDR_IRS | DAVINCI_I2C_MDR_MST | DAVINCI_I2C_MDR_STT;
+ /* Take I2C out of reset and configure it as master */
+ flag = DAVINCI_I2C_MDR_IRS | DAVINCI_I2C_MDR_MST;
/* if the slave address is ten bit address, enable XA bit */
if (msg->flags & I2C_M_TEN)
flag |= DAVINCI_I2C_MDR_XA;
if (!(msg->flags & I2C_M_RD))
flag |= DAVINCI_I2C_MDR_TRX;
- if (stop)
- flag |= DAVINCI_I2C_MDR_STP;
- if (msg->len == 0) {
+ if (msg->len == 0)
flag |= DAVINCI_I2C_MDR_RM;
- flag &= ~DAVINCI_I2C_MDR_STP;
- }
/* Enable receive or transmit interrupts */
w = davinci_i2c_read_reg(dev, DAVINCI_I2C_IMR_REG);
@@ -358,17 +353,28 @@
dev->terminate = 0;
/*
+ * Write mode register first as needed for correct behaviour
+ * on OMAP-L138, but don't set STT yet to avoid a race with XRDY
+ * occuring before we have loaded DXR
+ */
+ davinci_i2c_write_reg(dev, DAVINCI_I2C_MDR_REG, flag);
+
+ /*
* First byte should be set here, not after interrupt,
* because transmit-data-ready interrupt can come before
* NACK-interrupt during sending of previous message and
* ICDXR may have wrong data
+ * It also saves us one interrupt, slightly faster
*/
if ((!(msg->flags & I2C_M_RD)) && dev->buf_len) {
davinci_i2c_write_reg(dev, DAVINCI_I2C_DXR_REG, *dev->buf++);
dev->buf_len--;
}
- /* write the data into mode register; start transmitting */
+ /* Set STT to begin transmit now DXR is loaded */
+ flag |= DAVINCI_I2C_MDR_STT;
+ if (stop && msg->len != 0)
+ flag |= DAVINCI_I2C_MDR_STP;
davinci_i2c_write_reg(dev, DAVINCI_I2C_MDR_REG, flag);
r = wait_for_completion_interruptible_timeout(&dev->cmd_complete,
diff --git a/drivers/i2c/busses/i2c-ibm_iic.c b/drivers/i2c/busses/i2c-ibm_iic.c
index 43ca32f..89eedf4 100644
--- a/drivers/i2c/busses/i2c-ibm_iic.c
+++ b/drivers/i2c/busses/i2c-ibm_iic.c
@@ -761,6 +761,9 @@
dev_info(&ofdev->dev, "using %s mode\n",
dev->fast_mode ? "fast (400 kHz)" : "standard (100 kHz)");
+ /* Now register all the child nodes */
+ of_i2c_register_devices(adap);
+
return 0;
error_cleanup:
diff --git a/drivers/i2c/busses/i2c-imx.c b/drivers/i2c/busses/i2c-imx.c
index d1ff940..4c2a62b 100644
--- a/drivers/i2c/busses/i2c-imx.c
+++ b/drivers/i2c/busses/i2c-imx.c
@@ -159,15 +159,9 @@
static int i2c_imx_trx_complete(struct imx_i2c_struct *i2c_imx)
{
- int result;
+ wait_event_timeout(i2c_imx->queue, i2c_imx->i2csr & I2SR_IIF, HZ / 10);
- result = wait_event_interruptible_timeout(i2c_imx->queue,
- i2c_imx->i2csr & I2SR_IIF, HZ / 10);
-
- if (unlikely(result < 0)) {
- dev_dbg(&i2c_imx->adapter.dev, "<%s> result < 0\n", __func__);
- return result;
- } else if (unlikely(!(i2c_imx->i2csr & I2SR_IIF))) {
+ if (unlikely(!(i2c_imx->i2csr & I2SR_IIF))) {
dev_dbg(&i2c_imx->adapter.dev, "<%s> Timeout\n", __func__);
return -ETIMEDOUT;
}
@@ -295,7 +289,7 @@
i2c_imx->i2csr = temp;
temp &= ~I2SR_IIF;
writeb(temp, i2c_imx->base + IMX_I2C_I2SR);
- wake_up_interruptible(&i2c_imx->queue);
+ wake_up(&i2c_imx->queue);
return IRQ_HANDLED;
}
diff --git a/drivers/i2c/busses/i2c-mpc.c b/drivers/i2c/busses/i2c-mpc.c
index a1c419a..b74e6dc 100644
--- a/drivers/i2c/busses/i2c-mpc.c
+++ b/drivers/i2c/busses/i2c-mpc.c
@@ -632,6 +632,7 @@
dev_err(i2c->dev, "failed to add adapter\n");
goto fail_add;
}
+ of_i2c_register_devices(&i2c->adap);
return result;
diff --git a/drivers/i2c/busses/i2c-pca-isa.c b/drivers/i2c/busses/i2c-pca-isa.c
index bbd7760..29933f8 100644
--- a/drivers/i2c/busses/i2c-pca-isa.c
+++ b/drivers/i2c/busses/i2c-pca-isa.c
@@ -71,8 +71,8 @@
static int pca_isa_waitforcompletion(void *pd)
{
- long ret = ~0;
unsigned long timeout;
+ long ret;
if (irq > -1) {
ret = wait_event_timeout(pca_wait,
@@ -81,11 +81,15 @@
} else {
/* Do polling */
timeout = jiffies + pca_isa_ops.timeout;
- while (((pca_isa_readbyte(pd, I2C_PCA_CON)
- & I2C_PCA_CON_SI) == 0)
- && (ret = time_before(jiffies, timeout)))
+ do {
+ ret = time_before(jiffies, timeout);
+ if (pca_isa_readbyte(pd, I2C_PCA_CON)
+ & I2C_PCA_CON_SI)
+ break;
udelay(100);
+ } while (ret);
}
+
return ret > 0;
}
diff --git a/drivers/i2c/busses/i2c-pca-platform.c b/drivers/i2c/busses/i2c-pca-platform.c
index ef5c784..5f6d7f8 100644
--- a/drivers/i2c/busses/i2c-pca-platform.c
+++ b/drivers/i2c/busses/i2c-pca-platform.c
@@ -80,8 +80,8 @@
static int i2c_pca_pf_waitforcompletion(void *pd)
{
struct i2c_pca_pf_data *i2c = pd;
- long ret = ~0;
unsigned long timeout;
+ long ret;
if (i2c->irq) {
ret = wait_event_timeout(i2c->wait,
@@ -90,10 +90,13 @@
} else {
/* Do polling */
timeout = jiffies + i2c->adap.timeout;
- while (((i2c->algo_data.read_byte(i2c, I2C_PCA_CON)
- & I2C_PCA_CON_SI) == 0)
- && (ret = time_before(jiffies, timeout)))
+ do {
+ ret = time_before(jiffies, timeout);
+ if (i2c->algo_data.read_byte(i2c, I2C_PCA_CON)
+ & I2C_PCA_CON_SI)
+ break;
udelay(100);
+ } while (ret);
}
return ret > 0;
diff --git a/drivers/i2c/i2c-core.c b/drivers/i2c/i2c-core.c
index 6649176..bea4c50 100644
--- a/drivers/i2c/i2c-core.c
+++ b/drivers/i2c/i2c-core.c
@@ -32,7 +32,6 @@
#include <linux/init.h>
#include <linux/idr.h>
#include <linux/mutex.h>
-#include <linux/of_i2c.h>
#include <linux/of_device.h>
#include <linux/completion.h>
#include <linux/hardirq.h>
@@ -197,11 +196,12 @@
{
const struct dev_pm_ops *pm = dev->driver ? dev->driver->pm : NULL;
- if (pm_runtime_suspended(dev))
- return 0;
-
- if (pm)
- return pm->suspend ? pm->suspend(dev) : 0;
+ if (pm) {
+ if (pm_runtime_suspended(dev))
+ return 0;
+ else
+ return pm->suspend ? pm->suspend(dev) : 0;
+ }
return i2c_legacy_suspend(dev, PMSG_SUSPEND);
}
@@ -216,12 +216,6 @@
else
ret = i2c_legacy_resume(dev);
- if (!ret) {
- pm_runtime_disable(dev);
- pm_runtime_set_active(dev);
- pm_runtime_enable(dev);
- }
-
return ret;
}
@@ -229,11 +223,12 @@
{
const struct dev_pm_ops *pm = dev->driver ? dev->driver->pm : NULL;
- if (pm_runtime_suspended(dev))
- return 0;
-
- if (pm)
- return pm->freeze ? pm->freeze(dev) : 0;
+ if (pm) {
+ if (pm_runtime_suspended(dev))
+ return 0;
+ else
+ return pm->freeze ? pm->freeze(dev) : 0;
+ }
return i2c_legacy_suspend(dev, PMSG_FREEZE);
}
@@ -242,11 +237,12 @@
{
const struct dev_pm_ops *pm = dev->driver ? dev->driver->pm : NULL;
- if (pm_runtime_suspended(dev))
- return 0;
-
- if (pm)
- return pm->thaw ? pm->thaw(dev) : 0;
+ if (pm) {
+ if (pm_runtime_suspended(dev))
+ return 0;
+ else
+ return pm->thaw ? pm->thaw(dev) : 0;
+ }
return i2c_legacy_resume(dev);
}
@@ -255,11 +251,12 @@
{
const struct dev_pm_ops *pm = dev->driver ? dev->driver->pm : NULL;
- if (pm_runtime_suspended(dev))
- return 0;
-
- if (pm)
- return pm->poweroff ? pm->poweroff(dev) : 0;
+ if (pm) {
+ if (pm_runtime_suspended(dev))
+ return 0;
+ else
+ return pm->poweroff ? pm->poweroff(dev) : 0;
+ }
return i2c_legacy_suspend(dev, PMSG_HIBERNATE);
}
@@ -876,9 +873,6 @@
if (adap->nr < __i2c_first_dynamic_bus_num)
i2c_scan_static_board_info(adap);
- /* Register devices from the device tree */
- of_i2c_register_devices(adap);
-
/* Notify drivers */
mutex_lock(&core_lock);
bus_for_each_drv(&i2c_bus_type, NULL, adap, __process_new_adapter);
diff --git a/drivers/idle/intel_idle.c b/drivers/idle/intel_idle.c
index 0906fc5..c37ef64 100644
--- a/drivers/idle/intel_idle.c
+++ b/drivers/idle/intel_idle.c
@@ -157,13 +157,13 @@
{ /* MWAIT C5 */ },
{ /* MWAIT C6 */
.name = "ATM-C6",
- .desc = "MWAIT 0x40",
- .driver_data = (void *) 0x40,
+ .desc = "MWAIT 0x52",
+ .driver_data = (void *) 0x52,
.flags = CPUIDLE_FLAG_TIME_VALID | CPUIDLE_FLAG_TLB_FLUSHED,
- .exit_latency = 200,
+ .exit_latency = 140,
.power_usage = 150,
- .target_residency = 800,
- .enter = NULL }, /* disabled */
+ .target_residency = 560,
+ .enter = &intel_idle },
};
/**
diff --git a/drivers/input/evdev.c b/drivers/input/evdev.c
index c908c5f..9ddafc3 100644
--- a/drivers/input/evdev.c
+++ b/drivers/input/evdev.c
@@ -669,6 +669,9 @@
if ((_IOC_NR(cmd) & ~ABS_MAX) == _IOC_NR(EVIOCGABS(0))) {
+ if (!dev->absinfo)
+ return -EINVAL;
+
t = _IOC_NR(cmd) & ABS_MAX;
abs = dev->absinfo[t];
@@ -680,10 +683,13 @@
}
}
- if (_IOC_DIR(cmd) == _IOC_READ) {
+ if (_IOC_DIR(cmd) == _IOC_WRITE) {
if ((_IOC_NR(cmd) & ~ABS_MAX) == _IOC_NR(EVIOCSABS(0))) {
+ if (!dev->absinfo)
+ return -EINVAL;
+
t = _IOC_NR(cmd) & ABS_MAX;
if (copy_from_user(&abs, p, min_t(size_t,
diff --git a/drivers/input/joydev.c b/drivers/input/joydev.c
index d85bd8a..22239e9 100644
--- a/drivers/input/joydev.c
+++ b/drivers/input/joydev.c
@@ -483,6 +483,9 @@
memcpy(joydev->abspam, abspam, len);
+ for (i = 0; i < joydev->nabs; i++)
+ joydev->absmap[joydev->abspam[i]] = i;
+
out:
kfree(abspam);
return retval;
diff --git a/drivers/input/misc/uinput.c b/drivers/input/misc/uinput.c
index 0d4266a..3606985 100644
--- a/drivers/input/misc/uinput.c
+++ b/drivers/input/misc/uinput.c
@@ -404,6 +404,13 @@
retval = uinput_validate_absbits(dev);
if (retval < 0)
goto exit;
+ if (test_bit(ABS_MT_SLOT, dev->absbit)) {
+ int nslot = input_abs_get_max(dev, ABS_MT_SLOT) + 1;
+ input_mt_create_slots(dev, nslot);
+ input_set_events_per_packet(dev, 6 * nslot);
+ } else if (test_bit(ABS_MT_POSITION_X, dev->absbit)) {
+ input_set_events_per_packet(dev, 60);
+ }
}
udev->state = UIST_SETUP_COMPLETE;
diff --git a/drivers/input/tablet/wacom_sys.c b/drivers/input/tablet/wacom_sys.c
index 42ba369..b35876e 100644
--- a/drivers/input/tablet/wacom_sys.c
+++ b/drivers/input/tablet/wacom_sys.c
@@ -103,27 +103,26 @@
static int wacom_open(struct input_dev *dev)
{
struct wacom *wacom = input_get_drvdata(dev);
+ int retval = 0;
+
+ if (usb_autopm_get_interface(wacom->intf) < 0)
+ return -EIO;
mutex_lock(&wacom->lock);
- wacom->irq->dev = wacom->usbdev;
-
- if (usb_autopm_get_interface(wacom->intf) < 0) {
- mutex_unlock(&wacom->lock);
- return -EIO;
- }
-
if (usb_submit_urb(wacom->irq, GFP_KERNEL)) {
- usb_autopm_put_interface(wacom->intf);
- mutex_unlock(&wacom->lock);
- return -EIO;
+ retval = -EIO;
+ goto out;
}
wacom->open = true;
wacom->intf->needs_remote_wakeup = 1;
+out:
mutex_unlock(&wacom->lock);
- return 0;
+ if (retval)
+ usb_autopm_put_interface(wacom->intf);
+ return retval;
}
static void wacom_close(struct input_dev *dev)
@@ -135,6 +134,8 @@
wacom->open = false;
wacom->intf->needs_remote_wakeup = 0;
mutex_unlock(&wacom->lock);
+
+ usb_autopm_put_interface(wacom->intf);
}
static int wacom_parse_hid(struct usb_interface *intf, struct hid_descriptor *hid_desc,
diff --git a/drivers/input/tablet/wacom_wac.c b/drivers/input/tablet/wacom_wac.c
index 6e29bad..47fd7a0 100644
--- a/drivers/input/tablet/wacom_wac.c
+++ b/drivers/input/tablet/wacom_wac.c
@@ -442,8 +442,10 @@
/* general pen packet */
if ((data[1] & 0xb8) == 0xa0) {
t = (data[6] << 2) | ((data[7] >> 6) & 3);
- if (features->type >= INTUOS4S && features->type <= INTUOS4L)
+ if ((features->type >= INTUOS4S && features->type <= INTUOS4L) ||
+ features->type == WACOM_21UX2) {
t = (t << 1) | (data[1] & 1);
+ }
input_report_abs(input, ABS_PRESSURE, t);
input_report_abs(input, ABS_TILT_X,
((data[7] << 1) & 0x7e) | (data[8] >> 7));
diff --git a/drivers/isdn/sc/interrupt.c b/drivers/isdn/sc/interrupt.c
index 485be8b..f0225bc 100644
--- a/drivers/isdn/sc/interrupt.c
+++ b/drivers/isdn/sc/interrupt.c
@@ -112,11 +112,19 @@
}
else if(callid>=0x0000 && callid<=0x7FFF)
{
+ int len;
+
pr_debug("%s: Got Incoming Call\n",
sc_adapter[card]->devicename);
- strcpy(setup.phone,&(rcvmsg.msg_data.byte_array[4]));
- strcpy(setup.eazmsn,
- sc_adapter[card]->channel[rcvmsg.phy_link_no-1].dn);
+ len = strlcpy(setup.phone, &(rcvmsg.msg_data.byte_array[4]),
+ sizeof(setup.phone));
+ if (len >= sizeof(setup.phone))
+ continue;
+ len = strlcpy(setup.eazmsn,
+ sc_adapter[card]->channel[rcvmsg.phy_link_no - 1].dn,
+ sizeof(setup.eazmsn));
+ if (len >= sizeof(setup.eazmsn))
+ continue;
setup.si1 = 7;
setup.si2 = 0;
setup.plan = 0;
@@ -176,7 +184,9 @@
* Handle a GetMyNumber Rsp
*/
if (IS_CE_MESSAGE(rcvmsg,Call,0,GetMyNumber)){
- strcpy(sc_adapter[card]->channel[rcvmsg.phy_link_no-1].dn,rcvmsg.msg_data.byte_array);
+ strlcpy(sc_adapter[card]->channel[rcvmsg.phy_link_no - 1].dn,
+ rcvmsg.msg_data.byte_array,
+ sizeof(rcvmsg.msg_data.byte_array));
continue;
}
diff --git a/drivers/md/bitmap.c b/drivers/md/bitmap.c
index ed4900a..e4fb58d 100644
--- a/drivers/md/bitmap.c
+++ b/drivers/md/bitmap.c
@@ -1000,10 +1000,11 @@
page = bitmap->sb_page;
offset = sizeof(bitmap_super_t);
if (!file)
- read_sb_page(bitmap->mddev,
- bitmap->mddev->bitmap_info.offset,
- page,
- index, count);
+ page = read_sb_page(
+ bitmap->mddev,
+ bitmap->mddev->bitmap_info.offset,
+ page,
+ index, count);
} else if (file) {
page = read_page(file, index, bitmap, count);
offset = 0;
diff --git a/drivers/md/raid1.c b/drivers/md/raid1.c
index ad83a4d..0b830bb 100644
--- a/drivers/md/raid1.c
+++ b/drivers/md/raid1.c
@@ -1839,7 +1839,9 @@
/* take from bio_init */
bio->bi_next = NULL;
+ bio->bi_flags &= ~(BIO_POOL_MASK-1);
bio->bi_flags |= 1 << BIO_UPTODATE;
+ bio->bi_comp_cpu = -1;
bio->bi_rw = READ;
bio->bi_vcnt = 0;
bio->bi_idx = 0;
@@ -1912,7 +1914,7 @@
!test_bit(MD_RECOVERY_REQUESTED, &mddev->recovery))
break;
BUG_ON(sync_blocks < (PAGE_SIZE>>9));
- if (len > (sync_blocks<<9))
+ if ((len >> 9) > sync_blocks)
len = sync_blocks<<9;
}
diff --git a/drivers/media/IR/ir-keytable.c b/drivers/media/IR/ir-keytable.c
index 7e82a9d..7961d59 100644
--- a/drivers/media/IR/ir-keytable.c
+++ b/drivers/media/IR/ir-keytable.c
@@ -319,7 +319,7 @@
* a keyup event might follow immediately after the keydown.
*/
spin_lock_irqsave(&ir->keylock, flags);
- if (time_is_after_eq_jiffies(ir->keyup_jiffies))
+ if (time_is_before_eq_jiffies(ir->keyup_jiffies))
ir_keyup(ir);
spin_unlock_irqrestore(&ir->keylock, flags);
}
@@ -510,6 +510,13 @@
(ir_dev->props && ir_dev->props->driver_type == RC_DRIVER_IR_RAW) ?
" in raw mode" : "");
+ /*
+ * Default delay of 250ms is too short for some protocols, expecially
+ * since the timeout is currently set to 250ms. Increase it to 500ms,
+ * to avoid wrong repetition of the keycodes.
+ */
+ input_dev->rep[REP_DELAY] = 500;
+
return 0;
out_event:
diff --git a/drivers/media/IR/ir-lirc-codec.c b/drivers/media/IR/ir-lirc-codec.c
index 77b5946..e63f757 100644
--- a/drivers/media/IR/ir-lirc-codec.c
+++ b/drivers/media/IR/ir-lirc-codec.c
@@ -267,7 +267,7 @@
features |= LIRC_CAN_SET_SEND_CARRIER;
if (ir_dev->props->s_tx_duty_cycle)
- features |= LIRC_CAN_SET_REC_DUTY_CYCLE;
+ features |= LIRC_CAN_SET_SEND_DUTY_CYCLE;
}
if (ir_dev->props->s_rx_carrier_range)
diff --git a/drivers/media/IR/ir-raw-event.c b/drivers/media/IR/ir-raw-event.c
index 43094e7..8e0e1b1 100644
--- a/drivers/media/IR/ir-raw-event.c
+++ b/drivers/media/IR/ir-raw-event.c
@@ -279,9 +279,11 @@
"rc%u", (unsigned int)ir->devno);
if (IS_ERR(ir->raw->thread)) {
+ int ret = PTR_ERR(ir->raw->thread);
+
kfree(ir->raw);
ir->raw = NULL;
- return PTR_ERR(ir->raw->thread);
+ return ret;
}
mutex_lock(&ir_raw_handler_lock);
diff --git a/drivers/media/IR/ir-sysfs.c b/drivers/media/IR/ir-sysfs.c
index 96dafc4..46d4246 100644
--- a/drivers/media/IR/ir-sysfs.c
+++ b/drivers/media/IR/ir-sysfs.c
@@ -67,13 +67,14 @@
char *tmp = buf;
int i;
- if (ir_dev->props->driver_type == RC_DRIVER_SCANCODE) {
+ if (ir_dev->props && ir_dev->props->driver_type == RC_DRIVER_SCANCODE) {
enabled = ir_dev->rc_tab.ir_type;
allowed = ir_dev->props->allowed_protos;
- } else {
+ } else if (ir_dev->raw) {
enabled = ir_dev->raw->enabled_protocols;
allowed = ir_raw_get_allowed_protocols();
- }
+ } else
+ return sprintf(tmp, "[builtin]\n");
IR_dprintk(1, "allowed - 0x%llx, enabled - 0x%llx\n",
(long long)allowed,
@@ -121,10 +122,14 @@
int rc, i, count = 0;
unsigned long flags;
- if (ir_dev->props->driver_type == RC_DRIVER_SCANCODE)
+ if (ir_dev->props && ir_dev->props->driver_type == RC_DRIVER_SCANCODE)
type = ir_dev->rc_tab.ir_type;
- else
+ else if (ir_dev->raw)
type = ir_dev->raw->enabled_protocols;
+ else {
+ IR_dprintk(1, "Protocol switching not supported\n");
+ return -EINVAL;
+ }
while ((tmp = strsep((char **) &data, " \n")) != NULL) {
if (!*tmp)
@@ -185,7 +190,7 @@
}
}
- if (ir_dev->props->driver_type == RC_DRIVER_SCANCODE) {
+ if (ir_dev->props && ir_dev->props->driver_type == RC_DRIVER_SCANCODE) {
spin_lock_irqsave(&ir_dev->rc_tab.lock, flags);
ir_dev->rc_tab.ir_type = type;
spin_unlock_irqrestore(&ir_dev->rc_tab.lock, flags);
diff --git a/drivers/media/IR/keymaps/rc-rc6-mce.c b/drivers/media/IR/keymaps/rc-rc6-mce.c
index 64264f7..39557ad 100644
--- a/drivers/media/IR/keymaps/rc-rc6-mce.c
+++ b/drivers/media/IR/keymaps/rc-rc6-mce.c
@@ -19,6 +19,7 @@
{ 0x800f0416, KEY_PLAY },
{ 0x800f0418, KEY_PAUSE },
+ { 0x800f046e, KEY_PLAYPAUSE },
{ 0x800f0419, KEY_STOP },
{ 0x800f0417, KEY_RECORD },
@@ -37,6 +38,8 @@
{ 0x800f0411, KEY_VOLUMEDOWN },
{ 0x800f0412, KEY_CHANNELUP },
{ 0x800f0413, KEY_CHANNELDOWN },
+ { 0x800f043a, KEY_BRIGHTNESSUP },
+ { 0x800f0480, KEY_BRIGHTNESSDOWN },
{ 0x800f0401, KEY_NUMERIC_1 },
{ 0x800f0402, KEY_NUMERIC_2 },
diff --git a/drivers/media/IR/mceusb.c b/drivers/media/IR/mceusb.c
index ac6bb2c..bc620e1 100644
--- a/drivers/media/IR/mceusb.c
+++ b/drivers/media/IR/mceusb.c
@@ -120,6 +120,10 @@
{ USB_DEVICE(VENDOR_PHILIPS, 0x0613) },
/* Philips eHome Infrared Transceiver */
{ USB_DEVICE(VENDOR_PHILIPS, 0x0815) },
+ /* Philips/Spinel plus IR transceiver for ASUS */
+ { USB_DEVICE(VENDOR_PHILIPS, 0x206c) },
+ /* Philips/Spinel plus IR transceiver for ASUS */
+ { USB_DEVICE(VENDOR_PHILIPS, 0x2088) },
/* Realtek MCE IR Receiver */
{ USB_DEVICE(VENDOR_REALTEK, 0x0161) },
/* SMK/Toshiba G83C0004D410 */
diff --git a/drivers/media/dvb/dvb-usb/dib0700_core.c b/drivers/media/dvb/dvb-usb/dib0700_core.c
index fe81834..48397f1 100644
--- a/drivers/media/dvb/dvb-usb/dib0700_core.c
+++ b/drivers/media/dvb/dvb-usb/dib0700_core.c
@@ -673,9 +673,6 @@
else
dev->props.rc.core.bulk_mode = false;
- /* Need a higher delay, to avoid wrong repeat */
- dev->rc_input_dev->rep[REP_DELAY] = 500;
-
dib0700_rc_setup(dev);
return 0;
diff --git a/drivers/media/dvb/dvb-usb/dib0700_devices.c b/drivers/media/dvb/dvb-usb/dib0700_devices.c
index f634d2e..e06acd1 100644
--- a/drivers/media/dvb/dvb-usb/dib0700_devices.c
+++ b/drivers/media/dvb/dvb-usb/dib0700_devices.c
@@ -940,6 +940,58 @@
return adap->fe == NULL ? -ENODEV : 0;
}
+/* STK7770P */
+static struct dib7000p_config dib7770p_dib7000p_config = {
+ .output_mpeg2_in_188_bytes = 1,
+
+ .agc_config_count = 1,
+ .agc = &dib7070_agc_config,
+ .bw = &dib7070_bw_config_12_mhz,
+ .tuner_is_baseband = 1,
+ .spur_protect = 1,
+
+ .gpio_dir = DIB7000P_GPIO_DEFAULT_DIRECTIONS,
+ .gpio_val = DIB7000P_GPIO_DEFAULT_VALUES,
+ .gpio_pwm_pos = DIB7000P_GPIO_DEFAULT_PWM_POS,
+
+ .hostbus_diversity = 1,
+ .enable_current_mirror = 1,
+ .disable_sample_and_hold = 0,
+};
+
+static int stk7770p_frontend_attach(struct dvb_usb_adapter *adap)
+{
+ struct usb_device_descriptor *p = &adap->dev->udev->descriptor;
+ if (p->idVendor == cpu_to_le16(USB_VID_PINNACLE) &&
+ p->idProduct == cpu_to_le16(USB_PID_PINNACLE_PCTV72E))
+ dib0700_set_gpio(adap->dev, GPIO6, GPIO_OUT, 0);
+ else
+ dib0700_set_gpio(adap->dev, GPIO6, GPIO_OUT, 1);
+ msleep(10);
+ dib0700_set_gpio(adap->dev, GPIO9, GPIO_OUT, 1);
+ dib0700_set_gpio(adap->dev, GPIO4, GPIO_OUT, 1);
+ dib0700_set_gpio(adap->dev, GPIO7, GPIO_OUT, 1);
+ dib0700_set_gpio(adap->dev, GPIO10, GPIO_OUT, 0);
+
+ dib0700_ctrl_clock(adap->dev, 72, 1);
+
+ msleep(10);
+ dib0700_set_gpio(adap->dev, GPIO10, GPIO_OUT, 1);
+ msleep(10);
+ dib0700_set_gpio(adap->dev, GPIO0, GPIO_OUT, 1);
+
+ if (dib7000p_i2c_enumeration(&adap->dev->i2c_adap, 1, 18,
+ &dib7770p_dib7000p_config) != 0) {
+ err("%s: dib7000p_i2c_enumeration failed. Cannot continue\n",
+ __func__);
+ return -ENODEV;
+ }
+
+ adap->fe = dvb_attach(dib7000p_attach, &adap->dev->i2c_adap, 0x80,
+ &dib7770p_dib7000p_config);
+ return adap->fe == NULL ? -ENODEV : 0;
+}
+
/* DIB807x generic */
static struct dibx000_agc_config dib807x_agc_config[2] = {
{
@@ -1781,7 +1833,7 @@
/* 60 */{ USB_DEVICE(USB_VID_TERRATEC, USB_PID_TERRATEC_CINERGY_T_XXS_2) },
{ USB_DEVICE(USB_VID_DIBCOM, USB_PID_DIBCOM_STK807XPVR) },
{ USB_DEVICE(USB_VID_DIBCOM, USB_PID_DIBCOM_STK807XP) },
- { USB_DEVICE(USB_VID_PIXELVIEW, USB_PID_PIXELVIEW_SBTVD) },
+ { USB_DEVICE_VER(USB_VID_PIXELVIEW, USB_PID_PIXELVIEW_SBTVD, 0x000, 0x3f00) },
{ USB_DEVICE(USB_VID_EVOLUTEPC, USB_PID_TVWAY_PLUS) },
/* 65 */{ USB_DEVICE(USB_VID_PINNACLE, USB_PID_PINNACLE_PCTV73ESE) },
{ USB_DEVICE(USB_VID_PINNACLE, USB_PID_PINNACLE_PCTV282E) },
@@ -2406,7 +2458,7 @@
.pid_filter_count = 32,
.pid_filter = stk70x0p_pid_filter,
.pid_filter_ctrl = stk70x0p_pid_filter_ctrl,
- .frontend_attach = stk7070p_frontend_attach,
+ .frontend_attach = stk7770p_frontend_attach,
.tuner_attach = dib7770p_tuner_attach,
DIB0700_DEFAULT_STREAMING_CONFIG(0x02),
diff --git a/drivers/media/dvb/dvb-usb/opera1.c b/drivers/media/dvb/dvb-usb/opera1.c
index 6b22ec6..f896337 100644
--- a/drivers/media/dvb/dvb-usb/opera1.c
+++ b/drivers/media/dvb/dvb-usb/opera1.c
@@ -483,9 +483,7 @@
}
}
kfree(p);
- if (fw) {
- release_firmware(fw);
- }
+ release_firmware(fw);
return ret;
}
diff --git a/drivers/media/dvb/frontends/dib7000p.c b/drivers/media/dvb/frontends/dib7000p.c
index 2e28b97..3aed0d4 100644
--- a/drivers/media/dvb/frontends/dib7000p.c
+++ b/drivers/media/dvb/frontends/dib7000p.c
@@ -260,6 +260,9 @@
// dprintk( "908: %x, 909: %x\n", reg_908, reg_909);
+ reg_909 |= (state->cfg.disable_sample_and_hold & 1) << 4;
+ reg_908 |= (state->cfg.enable_current_mirror & 1) << 7;
+
dib7000p_write_word(state, 908, reg_908);
dib7000p_write_word(state, 909, reg_909);
}
@@ -778,7 +781,10 @@
default:
case GUARD_INTERVAL_1_32: value *= 1; break;
}
- state->div_sync_wait = (value * 3) / 2 + 32; // add 50% SFN margin + compensate for one DVSY-fifo TODO
+ if (state->cfg.diversity_delay == 0)
+ state->div_sync_wait = (value * 3) / 2 + 48; // add 50% SFN margin + compensate for one DVSY-fifo
+ else
+ state->div_sync_wait = (value * 3) / 2 + state->cfg.diversity_delay; // add 50% SFN margin + compensate for one DVSY-fifo
/* deactive the possibility of diversity reception if extended interleaver */
state->div_force_off = !1 && ch->u.ofdm.transmission_mode != TRANSMISSION_MODE_8K;
diff --git a/drivers/media/dvb/frontends/dib7000p.h b/drivers/media/dvb/frontends/dib7000p.h
index 805dd13..da17345 100644
--- a/drivers/media/dvb/frontends/dib7000p.h
+++ b/drivers/media/dvb/frontends/dib7000p.h
@@ -33,6 +33,11 @@
int (*agc_control) (struct dvb_frontend *, u8 before);
u8 output_mode;
+ u8 disable_sample_and_hold : 1;
+
+ u8 enable_current_mirror : 1;
+ u8 diversity_delay;
+
};
#define DEFAULT_DIB7000P_I2C_ADDRESS 18
diff --git a/drivers/media/dvb/siano/smscoreapi.c b/drivers/media/dvb/siano/smscoreapi.c
index d93468c..ff3b0fa 100644
--- a/drivers/media/dvb/siano/smscoreapi.c
+++ b/drivers/media/dvb/siano/smscoreapi.c
@@ -1098,33 +1098,26 @@
*
* @return pointer to descriptor on success, NULL on error.
*/
-struct smscore_buffer_t *smscore_getbuffer(struct smscore_device_t *coredev)
+
+struct smscore_buffer_t *get_entry(struct smscore_device_t *coredev)
{
struct smscore_buffer_t *cb = NULL;
unsigned long flags;
- DEFINE_WAIT(wait);
-
spin_lock_irqsave(&coredev->bufferslock, flags);
-
- /* This function must return a valid buffer, since the buffer list is
- * finite, we check that there is an available buffer, if not, we wait
- * until such buffer become available.
- */
-
- prepare_to_wait(&coredev->buffer_mng_waitq, &wait, TASK_INTERRUPTIBLE);
- if (list_empty(&coredev->buffers)) {
- spin_unlock_irqrestore(&coredev->bufferslock, flags);
- schedule();
- spin_lock_irqsave(&coredev->bufferslock, flags);
+ if (!list_empty(&coredev->buffers)) {
+ cb = (struct smscore_buffer_t *) coredev->buffers.next;
+ list_del(&cb->entry);
}
-
- finish_wait(&coredev->buffer_mng_waitq, &wait);
-
- cb = (struct smscore_buffer_t *) coredev->buffers.next;
- list_del(&cb->entry);
-
spin_unlock_irqrestore(&coredev->bufferslock, flags);
+ return cb;
+}
+
+struct smscore_buffer_t *smscore_getbuffer(struct smscore_device_t *coredev)
+{
+ struct smscore_buffer_t *cb = NULL;
+
+ wait_event(coredev->buffer_mng_waitq, (cb = get_entry(coredev)));
return cb;
}
diff --git a/drivers/media/radio/si470x/radio-si470x-i2c.c b/drivers/media/radio/si470x/radio-si470x-i2c.c
index 67a4ec8..4ce541a 100644
--- a/drivers/media/radio/si470x/radio-si470x-i2c.c
+++ b/drivers/media/radio/si470x/radio-si470x-i2c.c
@@ -395,7 +395,7 @@
radio->registers[POWERCFG] = POWERCFG_ENABLE;
if (si470x_set_register(radio, POWERCFG) < 0) {
retval = -EIO;
- goto err_all;
+ goto err_video;
}
msleep(110);
diff --git a/drivers/media/video/cx231xx/Makefile b/drivers/media/video/cx231xx/Makefile
index 755dd0c..6f2b573 100644
--- a/drivers/media/video/cx231xx/Makefile
+++ b/drivers/media/video/cx231xx/Makefile
@@ -11,4 +11,5 @@
EXTRA_CFLAGS += -Idrivers/media/common/tuners
EXTRA_CFLAGS += -Idrivers/media/dvb/dvb-core
EXTRA_CFLAGS += -Idrivers/media/dvb/frontends
+EXTRA_CFLAGS += -Idrivers/media/dvb/dvb-usb
diff --git a/drivers/media/video/cx231xx/cx231xx-cards.c b/drivers/media/video/cx231xx/cx231xx-cards.c
index 6bdc0ef..f2a4900 100644
--- a/drivers/media/video/cx231xx/cx231xx-cards.c
+++ b/drivers/media/video/cx231xx/cx231xx-cards.c
@@ -32,6 +32,7 @@
#include <media/v4l2-chip-ident.h>
#include <media/cx25840.h>
+#include "dvb-usb-ids.h"
#include "xc5000.h"
#include "cx231xx.h"
@@ -175,6 +176,8 @@
.driver_info = CX231XX_BOARD_CNXT_RDE_250},
{USB_DEVICE(0x0572, 0x58A1),
.driver_info = CX231XX_BOARD_CNXT_RDU_250},
+ {USB_DEVICE_VER(USB_VID_PIXELVIEW, USB_PID_PIXELVIEW_SBTVD, 0x4000,0x4fff),
+ .driver_info = CX231XX_BOARD_UNKNOWN},
{},
};
@@ -226,14 +229,16 @@
dev->board.name, dev->model);
/* set the direction for GPIO pins */
- cx231xx_set_gpio_direction(dev, dev->board.tuner_gpio->bit, 1);
- cx231xx_set_gpio_value(dev, dev->board.tuner_gpio->bit, 1);
- cx231xx_set_gpio_direction(dev, dev->board.tuner_sif_gpio, 1);
+ if (dev->board.tuner_gpio) {
+ cx231xx_set_gpio_direction(dev, dev->board.tuner_gpio->bit, 1);
+ cx231xx_set_gpio_value(dev, dev->board.tuner_gpio->bit, 1);
+ cx231xx_set_gpio_direction(dev, dev->board.tuner_sif_gpio, 1);
- /* request some modules if any required */
+ /* request some modules if any required */
- /* reset the Tuner */
- cx231xx_gpio_set(dev, dev->board.tuner_gpio);
+ /* reset the Tuner */
+ cx231xx_gpio_set(dev, dev->board.tuner_gpio);
+ }
/* set the mode to Analog mode initially */
cx231xx_set_mode(dev, CX231XX_ANALOG_MODE);
diff --git a/drivers/media/video/cx25840/cx25840-core.c b/drivers/media/video/cx25840/cx25840-core.c
index 86ca8c2..f5a3e74 100644
--- a/drivers/media/video/cx25840/cx25840-core.c
+++ b/drivers/media/video/cx25840/cx25840-core.c
@@ -1996,7 +1996,7 @@
state->volume = v4l2_ctrl_new_std(&state->hdl,
&cx25840_audio_ctrl_ops, V4L2_CID_AUDIO_VOLUME,
- 0, 65335, 65535 / 100, default_volume);
+ 0, 65535, 65535 / 100, default_volume);
state->mute = v4l2_ctrl_new_std(&state->hdl,
&cx25840_audio_ctrl_ops, V4L2_CID_AUDIO_MUTE,
0, 1, 1, 0);
diff --git a/drivers/media/video/cx88/Kconfig b/drivers/media/video/cx88/Kconfig
index 99dbae1..0fa85cb 100644
--- a/drivers/media/video/cx88/Kconfig
+++ b/drivers/media/video/cx88/Kconfig
@@ -17,7 +17,7 @@
config VIDEO_CX88_ALSA
tristate "Conexant 2388x DMA audio support"
- depends on VIDEO_CX88 && SND && EXPERIMENTAL
+ depends on VIDEO_CX88 && SND
select SND_PCM
---help---
This is a video4linux driver for direct (DMA) audio on
diff --git a/drivers/media/video/gspca/gspca.c b/drivers/media/video/gspca/gspca.c
index b984610..78abc1c 100644
--- a/drivers/media/video/gspca/gspca.c
+++ b/drivers/media/video/gspca/gspca.c
@@ -223,6 +223,7 @@
usb_rcvintpipe(dev, ep->bEndpointAddress),
buffer, buffer_len,
int_irq, (void *)gspca_dev, interval);
+ urb->transfer_flags |= URB_NO_TRANSFER_DMA_MAP;
gspca_dev->int_urb = urb;
ret = usb_submit_urb(urb, GFP_KERNEL);
if (ret < 0) {
diff --git a/drivers/media/video/gspca/sn9c20x.c b/drivers/media/video/gspca/sn9c20x.c
index 83a718f..9052d570 100644
--- a/drivers/media/video/gspca/sn9c20x.c
+++ b/drivers/media/video/gspca/sn9c20x.c
@@ -2357,8 +2357,7 @@
(data[33] << 10);
avg_lum >>= 9;
atomic_set(&sd->avg_lum, avg_lum);
- gspca_frame_add(gspca_dev, LAST_PACKET,
- data, len);
+ gspca_frame_add(gspca_dev, LAST_PACKET, NULL, 0);
return;
}
if (gspca_dev->last_packet_type == LAST_PACKET) {
diff --git a/drivers/media/video/ivtv/ivtvfb.c b/drivers/media/video/ivtv/ivtvfb.c
index be03a71..f0316d0 100644
--- a/drivers/media/video/ivtv/ivtvfb.c
+++ b/drivers/media/video/ivtv/ivtvfb.c
@@ -466,6 +466,8 @@
struct fb_vblank vblank;
u32 trace;
+ memset(&vblank, 0, sizeof(struct fb_vblank));
+
vblank.flags = FB_VBLANK_HAVE_COUNT |FB_VBLANK_HAVE_VCOUNT |
FB_VBLANK_HAVE_VSYNC;
trace = read_reg(IVTV_REG_DEC_LINE_FIELD) >> 16;
diff --git a/drivers/media/video/mem2mem_testdev.c b/drivers/media/video/mem2mem_testdev.c
index 4525335..a7210d9 100644
--- a/drivers/media/video/mem2mem_testdev.c
+++ b/drivers/media/video/mem2mem_testdev.c
@@ -239,7 +239,7 @@
return -EFAULT;
}
- if (in_buf->vb.size < out_buf->vb.size) {
+ if (in_buf->vb.size > out_buf->vb.size) {
v4l2_err(&dev->v4l2_dev, "Output buffer is too small\n");
return -EINVAL;
}
@@ -1014,6 +1014,7 @@
v4l2_m2m_release(dev->m2m_dev);
del_timer_sync(&dev->timer);
video_unregister_device(dev->vfd);
+ video_device_release(dev->vfd);
v4l2_device_unregister(&dev->v4l2_dev);
kfree(dev);
diff --git a/drivers/media/video/mt9m111.c b/drivers/media/video/mt9m111.c
index 758a4db..c71af4e 100644
--- a/drivers/media/video/mt9m111.c
+++ b/drivers/media/video/mt9m111.c
@@ -447,6 +447,9 @@
dev_dbg(&client->dev, "%s left=%d, top=%d, width=%d, height=%d\n",
__func__, rect.left, rect.top, rect.width, rect.height);
+ if (a->type != V4L2_BUF_TYPE_VIDEO_CAPTURE)
+ return -EINVAL;
+
ret = mt9m111_make_rect(client, &rect);
if (!ret)
mt9m111->rect = rect;
@@ -466,12 +469,14 @@
static int mt9m111_cropcap(struct v4l2_subdev *sd, struct v4l2_cropcap *a)
{
+ if (a->type != V4L2_BUF_TYPE_VIDEO_CAPTURE)
+ return -EINVAL;
+
a->bounds.left = MT9M111_MIN_DARK_COLS;
a->bounds.top = MT9M111_MIN_DARK_ROWS;
a->bounds.width = MT9M111_MAX_WIDTH;
a->bounds.height = MT9M111_MAX_HEIGHT;
a->defrect = a->bounds;
- a->type = V4L2_BUF_TYPE_VIDEO_CAPTURE;
a->pixelaspect.numerator = 1;
a->pixelaspect.denominator = 1;
@@ -487,6 +492,7 @@
mf->width = mt9m111->rect.width;
mf->height = mt9m111->rect.height;
mf->code = mt9m111->fmt->code;
+ mf->colorspace = mt9m111->fmt->colorspace;
mf->field = V4L2_FIELD_NONE;
return 0;
diff --git a/drivers/media/video/mt9v022.c b/drivers/media/video/mt9v022.c
index e7cd23c..b48473c 100644
--- a/drivers/media/video/mt9v022.c
+++ b/drivers/media/video/mt9v022.c
@@ -402,9 +402,6 @@
if (mt9v022->model != V4L2_IDENT_MT9V022IX7ATC)
return -EINVAL;
break;
- case 0:
- /* No format change, only geometry */
- break;
default:
return -EINVAL;
}
diff --git a/drivers/media/video/mx2_camera.c b/drivers/media/video/mx2_camera.c
index 66ff174..b6ea672 100644
--- a/drivers/media/video/mx2_camera.c
+++ b/drivers/media/video/mx2_camera.c
@@ -378,6 +378,9 @@
spin_lock_irqsave(&pcdev->lock, flags);
+ if (*fb_active == NULL)
+ goto out;
+
vb = &(*fb_active)->vb;
dev_dbg(pcdev->dev, "%s (vb=0x%p) 0x%08lx %d\n", __func__,
vb, vb->baddr, vb->bsize);
@@ -402,6 +405,7 @@
*fb_active = buf;
+out:
spin_unlock_irqrestore(&pcdev->lock, flags);
}
diff --git a/drivers/media/video/pvrusb2/pvrusb2-ctrl.c b/drivers/media/video/pvrusb2/pvrusb2-ctrl.c
index 1b992b84..55ea914 100644
--- a/drivers/media/video/pvrusb2/pvrusb2-ctrl.c
+++ b/drivers/media/video/pvrusb2/pvrusb2-ctrl.c
@@ -513,7 +513,7 @@
if (ret >= 0) {
ret = pvr2_ctrl_range_check(cptr,*valptr);
}
- if (maskptr) *maskptr = ~0;
+ *maskptr = ~0;
} else if (cptr->info->type == pvr2_ctl_bool) {
ret = parse_token(ptr,len,valptr,boolNames,
ARRAY_SIZE(boolNames));
@@ -522,7 +522,7 @@
} else if (ret == 0) {
*valptr = (*valptr & 1) ? !0 : 0;
}
- if (maskptr) *maskptr = 1;
+ *maskptr = 1;
} else if (cptr->info->type == pvr2_ctl_enum) {
ret = parse_token(
ptr,len,valptr,
@@ -531,7 +531,7 @@
if (ret >= 0) {
ret = pvr2_ctrl_range_check(cptr,*valptr);
}
- if (maskptr) *maskptr = ~0;
+ *maskptr = ~0;
} else if (cptr->info->type == pvr2_ctl_bitmask) {
ret = parse_tlist(
ptr,len,maskptr,valptr,
diff --git a/drivers/media/video/s5p-fimc/fimc-core.c b/drivers/media/video/s5p-fimc/fimc-core.c
index b151c7b..6961c55 100644
--- a/drivers/media/video/s5p-fimc/fimc-core.c
+++ b/drivers/media/video/s5p-fimc/fimc-core.c
@@ -393,6 +393,37 @@
dbg("ctx->out_order_1p= %d", ctx->out_order_1p);
}
+static void fimc_prepare_dma_offset(struct fimc_ctx *ctx, struct fimc_frame *f)
+{
+ struct samsung_fimc_variant *variant = ctx->fimc_dev->variant;
+
+ f->dma_offset.y_h = f->offs_h;
+ if (!variant->pix_hoff)
+ f->dma_offset.y_h *= (f->fmt->depth >> 3);
+
+ f->dma_offset.y_v = f->offs_v;
+
+ f->dma_offset.cb_h = f->offs_h;
+ f->dma_offset.cb_v = f->offs_v;
+
+ f->dma_offset.cr_h = f->offs_h;
+ f->dma_offset.cr_v = f->offs_v;
+
+ if (!variant->pix_hoff) {
+ if (f->fmt->planes_cnt == 3) {
+ f->dma_offset.cb_h >>= 1;
+ f->dma_offset.cr_h >>= 1;
+ }
+ if (f->fmt->color == S5P_FIMC_YCBCR420) {
+ f->dma_offset.cb_v >>= 1;
+ f->dma_offset.cr_v >>= 1;
+ }
+ }
+
+ dbg("in_offset: color= %d, y_h= %d, y_v= %d",
+ f->fmt->color, f->dma_offset.y_h, f->dma_offset.y_v);
+}
+
/**
* fimc_prepare_config - check dimensions, operation and color mode
* and pre-calculate offset and the scaling coefficients.
@@ -406,7 +437,6 @@
{
struct fimc_frame *s_frame, *d_frame;
struct fimc_vid_buffer *buf = NULL;
- struct samsung_fimc_variant *variant = ctx->fimc_dev->variant;
int ret = 0;
s_frame = &ctx->s_frame;
@@ -419,61 +449,16 @@
swap(d_frame->width, d_frame->height);
}
- /* Prepare the output offset ratios for scaler. */
- d_frame->dma_offset.y_h = d_frame->offs_h;
- if (!variant->pix_hoff)
- d_frame->dma_offset.y_h *= (d_frame->fmt->depth >> 3);
+ /* Prepare the DMA offset ratios for scaler. */
+ fimc_prepare_dma_offset(ctx, &ctx->s_frame);
+ fimc_prepare_dma_offset(ctx, &ctx->d_frame);
- d_frame->dma_offset.y_v = d_frame->offs_v;
-
- d_frame->dma_offset.cb_h = d_frame->offs_h;
- d_frame->dma_offset.cb_v = d_frame->offs_v;
-
- d_frame->dma_offset.cr_h = d_frame->offs_h;
- d_frame->dma_offset.cr_v = d_frame->offs_v;
-
- if (!variant->pix_hoff && d_frame->fmt->planes_cnt == 3) {
- d_frame->dma_offset.cb_h >>= 1;
- d_frame->dma_offset.cb_v >>= 1;
- d_frame->dma_offset.cr_h >>= 1;
- d_frame->dma_offset.cr_v >>= 1;
- }
-
- dbg("out offset: color= %d, y_h= %d, y_v= %d",
- d_frame->fmt->color,
- d_frame->dma_offset.y_h, d_frame->dma_offset.y_v);
-
- /* Prepare the input offset ratios for scaler. */
- s_frame->dma_offset.y_h = s_frame->offs_h;
- if (!variant->pix_hoff)
- s_frame->dma_offset.y_h *= (s_frame->fmt->depth >> 3);
- s_frame->dma_offset.y_v = s_frame->offs_v;
-
- s_frame->dma_offset.cb_h = s_frame->offs_h;
- s_frame->dma_offset.cb_v = s_frame->offs_v;
-
- s_frame->dma_offset.cr_h = s_frame->offs_h;
- s_frame->dma_offset.cr_v = s_frame->offs_v;
-
- if (!variant->pix_hoff && s_frame->fmt->planes_cnt == 3) {
- s_frame->dma_offset.cb_h >>= 1;
- s_frame->dma_offset.cb_v >>= 1;
- s_frame->dma_offset.cr_h >>= 1;
- s_frame->dma_offset.cr_v >>= 1;
- }
-
- dbg("in offset: color= %d, y_h= %d, y_v= %d",
- s_frame->fmt->color, s_frame->dma_offset.y_h,
- s_frame->dma_offset.y_v);
-
- fimc_set_yuv_order(ctx);
-
- /* Check against the scaler ratio. */
if (s_frame->height > (SCALER_MAX_VRATIO * d_frame->height) ||
s_frame->width > (SCALER_MAX_HRATIO * d_frame->width)) {
err("out of scaler range");
return -EINVAL;
}
+ fimc_set_yuv_order(ctx);
}
/* Input DMA mode is not allowed when the scaler is disabled. */
@@ -822,7 +807,8 @@
} else {
v4l2_err(&ctx->fimc_dev->m2m.v4l2_dev,
"Wrong buffer/video queue type (%d)\n", f->type);
- return -EINVAL;
+ ret = -EINVAL;
+ goto s_fmt_out;
}
pix = &f->fmt.pix;
@@ -1414,8 +1400,10 @@
}
fimc->work_queue = create_workqueue(dev_name(&fimc->pdev->dev));
- if (!fimc->work_queue)
+ if (!fimc->work_queue) {
+ ret = -ENOMEM;
goto err_irq;
+ }
ret = fimc_register_m2m_device(fimc);
if (ret)
@@ -1492,6 +1480,7 @@
};
static struct samsung_fimc_variant fimc01_variant_s5pv210 = {
+ .pix_hoff = 1,
.has_inp_rot = 1,
.has_out_rot = 1,
.min_inp_pixsize = 16,
@@ -1506,6 +1495,7 @@
};
static struct samsung_fimc_variant fimc2_variant_s5pv210 = {
+ .pix_hoff = 1,
.min_inp_pixsize = 16,
.min_out_pixsize = 32,
diff --git a/drivers/media/video/saa7134/saa7134-cards.c b/drivers/media/video/saa7134/saa7134-cards.c
index ec697fc..bb8d83d 100644
--- a/drivers/media/video/saa7134/saa7134-cards.c
+++ b/drivers/media/video/saa7134/saa7134-cards.c
@@ -4323,13 +4323,13 @@
},
[SAA7134_BOARD_BEHOLD_COLUMBUS_TVFM] = {
/* Beholder Intl. Ltd. 2008 */
- /*Dmitry Belimov <d.belimov@gmail.com> */
- .name = "Beholder BeholdTV Columbus TVFM",
+ /* Dmitry Belimov <d.belimov@gmail.com> */
+ .name = "Beholder BeholdTV Columbus TV/FM",
.audio_clock = 0x00187de7,
.tuner_type = TUNER_ALPS_TSBE5_PAL,
- .radio_type = UNSET,
- .tuner_addr = ADDR_UNSET,
- .radio_addr = ADDR_UNSET,
+ .radio_type = TUNER_TEA5767,
+ .tuner_addr = 0xc2 >> 1,
+ .radio_addr = 0xc0 >> 1,
.tda9887_conf = TDA9887_PRESENT,
.gpiomask = 0x000A8004,
.inputs = {{
diff --git a/drivers/media/video/saa7164/saa7164-buffer.c b/drivers/media/video/saa7164/saa7164-buffer.c
index 5713f3a..ddd25d3 100644
--- a/drivers/media/video/saa7164/saa7164-buffer.c
+++ b/drivers/media/video/saa7164/saa7164-buffer.c
@@ -136,10 +136,11 @@
int saa7164_buffer_dealloc(struct saa7164_tsport *port,
struct saa7164_buffer *buf)
{
- struct saa7164_dev *dev = port->dev;
+ struct saa7164_dev *dev;
- if ((buf == 0) || (port == 0))
+ if (!buf || !port)
return SAA_ERR_BAD_PARAMETER;
+ dev = port->dev;
dprintk(DBGLVL_BUF, "%s() deallocating buffer @ 0x%p\n", __func__, buf);
diff --git a/drivers/media/video/uvc/uvc_driver.c b/drivers/media/video/uvc/uvc_driver.c
index 8bdd940..2ac85d8 100644
--- a/drivers/media/video/uvc/uvc_driver.c
+++ b/drivers/media/video/uvc/uvc_driver.c
@@ -486,6 +486,12 @@
max(frame->dwFrameInterval[0],
frame->dwDefaultFrameInterval));
+ if (dev->quirks & UVC_QUIRK_RESTRICT_FRAME_RATE) {
+ frame->bFrameIntervalType = 1;
+ frame->dwFrameInterval[0] =
+ frame->dwDefaultFrameInterval;
+ }
+
uvc_trace(UVC_TRACE_DESCR, "- %ux%u (%u.%u fps)\n",
frame->wWidth, frame->wHeight,
10000000/frame->dwDefaultFrameInterval,
@@ -2026,6 +2032,15 @@
.bInterfaceClass = USB_CLASS_VENDOR_SPEC,
.bInterfaceSubClass = 1,
.bInterfaceProtocol = 0 },
+ /* Chicony CNF7129 (Asus EEE 100HE) */
+ { .match_flags = USB_DEVICE_ID_MATCH_DEVICE
+ | USB_DEVICE_ID_MATCH_INT_INFO,
+ .idVendor = 0x04f2,
+ .idProduct = 0xb071,
+ .bInterfaceClass = USB_CLASS_VIDEO,
+ .bInterfaceSubClass = 1,
+ .bInterfaceProtocol = 0,
+ .driver_info = UVC_QUIRK_RESTRICT_FRAME_RATE },
/* Alcor Micro AU3820 (Future Boy PC USB Webcam) */
{ .match_flags = USB_DEVICE_ID_MATCH_DEVICE
| USB_DEVICE_ID_MATCH_INT_INFO,
@@ -2091,6 +2106,15 @@
.bInterfaceProtocol = 0,
.driver_info = UVC_QUIRK_PROBE_MINMAX
| UVC_QUIRK_PROBE_DEF },
+ /* IMC Networks (Medion Akoya) */
+ { .match_flags = USB_DEVICE_ID_MATCH_DEVICE
+ | USB_DEVICE_ID_MATCH_INT_INFO,
+ .idVendor = 0x13d3,
+ .idProduct = 0x5103,
+ .bInterfaceClass = USB_CLASS_VIDEO,
+ .bInterfaceSubClass = 1,
+ .bInterfaceProtocol = 0,
+ .driver_info = UVC_QUIRK_STREAM_NO_FID },
/* Syntek (HP Spartan) */
{ .match_flags = USB_DEVICE_ID_MATCH_DEVICE
| USB_DEVICE_ID_MATCH_INT_INFO,
diff --git a/drivers/media/video/uvc/uvcvideo.h b/drivers/media/video/uvc/uvcvideo.h
index bdacf3b..892e0e5 100644
--- a/drivers/media/video/uvc/uvcvideo.h
+++ b/drivers/media/video/uvc/uvcvideo.h
@@ -182,6 +182,7 @@
#define UVC_QUIRK_IGNORE_SELECTOR_UNIT 0x00000020
#define UVC_QUIRK_FIX_BANDWIDTH 0x00000080
#define UVC_QUIRK_PROBE_DEF 0x00000100
+#define UVC_QUIRK_RESTRICT_FRAME_RATE 0x00000200
/* Format flags */
#define UVC_FMT_FLAG_COMPRESSED 0x00000001
diff --git a/drivers/media/video/v4l2-compat-ioctl32.c b/drivers/media/video/v4l2-compat-ioctl32.c
index 073f013..86294ed3 100644
--- a/drivers/media/video/v4l2-compat-ioctl32.c
+++ b/drivers/media/video/v4l2-compat-ioctl32.c
@@ -193,17 +193,24 @@
struct video_code32 {
char loadwhat[16]; /* name or tag of file being passed */
compat_int_t datasize;
- unsigned char *data;
+ compat_uptr_t data;
};
-static int get_microcode32(struct video_code *kp, struct video_code32 __user *up)
+static struct video_code __user *get_microcode32(struct video_code32 *kp)
{
- if (!access_ok(VERIFY_READ, up, sizeof(struct video_code32)) ||
- copy_from_user(kp->loadwhat, up->loadwhat, sizeof(up->loadwhat)) ||
- get_user(kp->datasize, &up->datasize) ||
- copy_from_user(kp->data, up->data, up->datasize))
- return -EFAULT;
- return 0;
+ struct video_code __user *up;
+
+ up = compat_alloc_user_space(sizeof(*up));
+
+ /*
+ * NOTE! We don't actually care if these fail. If the
+ * user address is invalid, the native ioctl will do
+ * the error handling for us
+ */
+ (void) copy_to_user(up->loadwhat, kp->loadwhat, sizeof(up->loadwhat));
+ (void) put_user(kp->datasize, &up->datasize);
+ (void) put_user(compat_ptr(kp->data), &up->data);
+ return up;
}
#define VIDIOCGTUNER32 _IOWR('v', 4, struct video_tuner32)
@@ -739,7 +746,7 @@
struct video_tuner vt;
struct video_buffer vb;
struct video_window vw;
- struct video_code vc;
+ struct video_code32 vc;
struct video_audio va;
#endif
struct v4l2_format v2f;
@@ -818,8 +825,11 @@
break;
case VIDIOCSMICROCODE:
- err = get_microcode32(&karg.vc, up);
- compatible_arg = 0;
+ /* Copy the 32-bit "video_code32" to kernel space */
+ if (copy_from_user(&karg.vc, up, sizeof(karg.vc)))
+ return -EFAULT;
+ /* Convert the 32-bit version to a 64-bit version in user space */
+ up = get_microcode32(&karg.vc);
break;
case VIDIOCSFREQ:
diff --git a/drivers/media/video/videobuf-dma-contig.c b/drivers/media/video/videobuf-dma-contig.c
index 372b87e..6ff9e4b 100644
--- a/drivers/media/video/videobuf-dma-contig.c
+++ b/drivers/media/video/videobuf-dma-contig.c
@@ -393,8 +393,10 @@
}
/* read() method */
- dma_free_coherent(q->dev, mem->size, mem->vaddr, mem->dma_handle);
- mem->vaddr = NULL;
+ if (mem->vaddr) {
+ dma_free_coherent(q->dev, mem->size, mem->vaddr, mem->dma_handle);
+ mem->vaddr = NULL;
+ }
}
EXPORT_SYMBOL_GPL(videobuf_dma_contig_free);
diff --git a/drivers/media/video/videobuf-dma-sg.c b/drivers/media/video/videobuf-dma-sg.c
index 06f9a9c..2ad0bc2 100644
--- a/drivers/media/video/videobuf-dma-sg.c
+++ b/drivers/media/video/videobuf-dma-sg.c
@@ -94,7 +94,7 @@
* must free the memory.
*/
static struct scatterlist *videobuf_pages_to_sg(struct page **pages,
- int nr_pages, int offset)
+ int nr_pages, int offset, size_t size)
{
struct scatterlist *sglist;
int i;
@@ -110,12 +110,14 @@
/* DMA to highmem pages might not work */
goto highmem;
sg_set_page(&sglist[0], pages[0], PAGE_SIZE - offset, offset);
+ size -= PAGE_SIZE - offset;
for (i = 1; i < nr_pages; i++) {
if (NULL == pages[i])
goto nopage;
if (PageHighMem(pages[i]))
goto highmem;
- sg_set_page(&sglist[i], pages[i], PAGE_SIZE, 0);
+ sg_set_page(&sglist[i], pages[i], min(PAGE_SIZE, size), 0);
+ size -= min(PAGE_SIZE, size);
}
return sglist;
@@ -170,7 +172,8 @@
first = (data & PAGE_MASK) >> PAGE_SHIFT;
last = ((data+size-1) & PAGE_MASK) >> PAGE_SHIFT;
- dma->offset = data & ~PAGE_MASK;
+ dma->offset = data & ~PAGE_MASK;
+ dma->size = size;
dma->nr_pages = last-first+1;
dma->pages = kmalloc(dma->nr_pages * sizeof(struct page *), GFP_KERNEL);
if (NULL == dma->pages)
@@ -252,7 +255,7 @@
if (dma->pages) {
dma->sglist = videobuf_pages_to_sg(dma->pages, dma->nr_pages,
- dma->offset);
+ dma->offset, dma->size);
}
if (dma->vaddr) {
dma->sglist = videobuf_vmalloc_to_sg(dma->vaddr,
diff --git a/drivers/misc/bh1780gli.c b/drivers/misc/bh1780gli.c
index 714c6b4..d5f3a3f 100644
--- a/drivers/misc/bh1780gli.c
+++ b/drivers/misc/bh1780gli.c
@@ -190,7 +190,6 @@
ddata = i2c_get_clientdata(client);
sysfs_remove_group(&client->dev.kobj, &bh1780_attr_group);
- i2c_set_clientdata(client, NULL);
kfree(ddata);
return 0;
diff --git a/drivers/mmc/core/core.c b/drivers/mmc/core/core.c
index 5db49b1..09eee6d 100644
--- a/drivers/mmc/core/core.c
+++ b/drivers/mmc/core/core.c
@@ -1631,6 +1631,19 @@
if (host->bus_ops && !host->bus_dead) {
if (host->bus_ops->suspend)
err = host->bus_ops->suspend(host);
+ if (err == -ENOSYS || !host->bus_ops->resume) {
+ /*
+ * We simply "remove" the card in this case.
+ * It will be redetected on resume.
+ */
+ if (host->bus_ops->remove)
+ host->bus_ops->remove(host);
+ mmc_claim_host(host);
+ mmc_detach_bus(host);
+ mmc_release_host(host);
+ host->pm_flags = 0;
+ err = 0;
+ }
}
mmc_bus_put(host);
diff --git a/drivers/mtd/nand/mxc_nand.c b/drivers/mtd/nand/mxc_nand.c
index b2828e8..214b03a 100644
--- a/drivers/mtd/nand/mxc_nand.c
+++ b/drivers/mtd/nand/mxc_nand.c
@@ -30,6 +30,8 @@
#include <linux/clk.h>
#include <linux/err.h>
#include <linux/io.h>
+#include <linux/irq.h>
+#include <linux/completion.h>
#include <asm/mach/flash.h>
#include <mach/mxc_nand.h>
@@ -151,7 +153,7 @@
int irq;
int eccsize;
- wait_queue_head_t irq_waitq;
+ struct completion op_completion;
uint8_t *data_buf;
unsigned int buf_start;
@@ -164,6 +166,7 @@
void (*send_read_id)(struct mxc_nand_host *);
uint16_t (*get_dev_status)(struct mxc_nand_host *);
int (*check_int)(struct mxc_nand_host *);
+ void (*irq_control)(struct mxc_nand_host *, int);
};
/* OOB placement block for use with hardware ecc generation */
@@ -216,9 +219,12 @@
{
struct mxc_nand_host *host = dev_id;
- disable_irq_nosync(irq);
+ if (!host->check_int(host))
+ return IRQ_NONE;
- wake_up(&host->irq_waitq);
+ host->irq_control(host, 0);
+
+ complete(&host->op_completion);
return IRQ_HANDLED;
}
@@ -245,11 +251,54 @@
if (!(tmp & NFC_V1_V2_CONFIG2_INT))
return 0;
- writew(tmp & ~NFC_V1_V2_CONFIG2_INT, NFC_V1_V2_CONFIG2);
+ if (!cpu_is_mx21())
+ writew(tmp & ~NFC_V1_V2_CONFIG2_INT, NFC_V1_V2_CONFIG2);
return 1;
}
+/*
+ * It has been observed that the i.MX21 cannot read the CONFIG2:INT bit
+ * if interrupts are masked (CONFIG1:INT_MSK is set). To handle this, the
+ * driver can enable/disable the irq line rather than simply masking the
+ * interrupts.
+ */
+static void irq_control_mx21(struct mxc_nand_host *host, int activate)
+{
+ if (activate)
+ enable_irq(host->irq);
+ else
+ disable_irq_nosync(host->irq);
+}
+
+static void irq_control_v1_v2(struct mxc_nand_host *host, int activate)
+{
+ uint16_t tmp;
+
+ tmp = readw(NFC_V1_V2_CONFIG1);
+
+ if (activate)
+ tmp &= ~NFC_V1_V2_CONFIG1_INT_MSK;
+ else
+ tmp |= NFC_V1_V2_CONFIG1_INT_MSK;
+
+ writew(tmp, NFC_V1_V2_CONFIG1);
+}
+
+static void irq_control_v3(struct mxc_nand_host *host, int activate)
+{
+ uint32_t tmp;
+
+ tmp = readl(NFC_V3_CONFIG2);
+
+ if (activate)
+ tmp &= ~NFC_V3_CONFIG2_INT_MSK;
+ else
+ tmp |= NFC_V3_CONFIG2_INT_MSK;
+
+ writel(tmp, NFC_V3_CONFIG2);
+}
+
/* This function polls the NANDFC to wait for the basic operation to
* complete by checking the INT bit of config2 register.
*/
@@ -259,10 +308,9 @@
if (useirq) {
if (!host->check_int(host)) {
-
- enable_irq(host->irq);
-
- wait_event(host->irq_waitq, host->check_int(host));
+ INIT_COMPLETION(host->op_completion);
+ host->irq_control(host, 1);
+ wait_for_completion(&host->op_completion);
}
} else {
while (max_retries-- > 0) {
@@ -799,6 +847,7 @@
NFC_V3_CONFIG2_2CMD_PHASES |
NFC_V3_CONFIG2_SPAS(mtd->oobsize >> 1) |
NFC_V3_CONFIG2_ST_CMD(0x70) |
+ NFC_V3_CONFIG2_INT_MSK |
NFC_V3_CONFIG2_NUM_ADDR_PHASE0;
if (chip->ecc.mode == NAND_ECC_HW)
@@ -1024,6 +1073,10 @@
host->send_read_id = send_read_id_v1_v2;
host->get_dev_status = get_dev_status_v1_v2;
host->check_int = check_int_v1_v2;
+ if (cpu_is_mx21())
+ host->irq_control = irq_control_mx21;
+ else
+ host->irq_control = irq_control_v1_v2;
}
if (nfc_is_v21()) {
@@ -1062,6 +1115,7 @@
host->send_read_id = send_read_id_v3;
host->check_int = check_int_v3;
host->get_dev_status = get_dev_status_v3;
+ host->irq_control = irq_control_v3;
oob_smallpage = &nandv2_hw_eccoob_smallpage;
oob_largepage = &nandv2_hw_eccoob_largepage;
} else
@@ -1093,14 +1147,34 @@
this->options |= NAND_USE_FLASH_BBT;
}
- init_waitqueue_head(&host->irq_waitq);
+ init_completion(&host->op_completion);
host->irq = platform_get_irq(pdev, 0);
+ /*
+ * mask the interrupt. For i.MX21 explicitely call
+ * irq_control_v1_v2 to use the mask bit. We can't call
+ * disable_irq_nosync() for an interrupt we do not own yet.
+ */
+ if (cpu_is_mx21())
+ irq_control_v1_v2(host, 0);
+ else
+ host->irq_control(host, 0);
+
err = request_irq(host->irq, mxc_nfc_irq, IRQF_DISABLED, DRIVER_NAME, host);
if (err)
goto eirq;
+ host->irq_control(host, 0);
+
+ /*
+ * Now that the interrupt is disabled make sure the interrupt
+ * mask bit is cleared on i.MX21. Otherwise we can't read
+ * the interrupt status bit on this machine.
+ */
+ if (cpu_is_mx21())
+ irq_control_v1_v2(host, 1);
+
/* first scan to find the device and get the page size */
if (nand_scan_ident(mtd, 1, NULL)) {
err = -ENXIO;
diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig
index 2cc81a5..5db667c 100644
--- a/drivers/net/Kconfig
+++ b/drivers/net/Kconfig
@@ -2428,7 +2428,7 @@
config MV643XX_ETH
tristate "Marvell Discovery (643XX) and Orion ethernet support"
- depends on MV64X60 || PPC32 || PLAT_ORION
+ depends on (MV64X60 || PPC32 || PLAT_ORION) && INET
select INET_LRO
select PHYLIB
help
@@ -2803,7 +2803,7 @@
config PASEMI_MAC
tristate "PA Semi 1/10Gbit MAC"
- depends on PPC_PASEMI && PCI
+ depends on PPC_PASEMI && PCI && INET
select PHYLIB
select INET_LRO
help
diff --git a/drivers/net/b44.c b/drivers/net/b44.c
index 1e620e2..efeffdf 100644
--- a/drivers/net/b44.c
+++ b/drivers/net/b44.c
@@ -2170,8 +2170,6 @@
dev->irq = sdev->irq;
SET_ETHTOOL_OPS(dev, &b44_ethtool_ops);
- netif_carrier_off(dev);
-
err = ssb_bus_powerup(sdev->bus, 0);
if (err) {
dev_err(sdev->dev,
@@ -2213,6 +2211,8 @@
goto err_out_powerdown;
}
+ netif_carrier_off(dev);
+
ssb_set_drvdata(sdev, dev);
/* Chip reset provides power to the b44 MAC & PCI cores, which
diff --git a/drivers/net/bonding/bond_main.c b/drivers/net/bonding/bond_main.c
index 3b16f62..e953c6a 100644
--- a/drivers/net/bonding/bond_main.c
+++ b/drivers/net/bonding/bond_main.c
@@ -5164,6 +5164,15 @@
res = dev_alloc_name(bond_dev, "bond%d");
if (res < 0)
goto out;
+ } else {
+ /*
+ * If we're given a name to register
+ * we need to ensure that its not already
+ * registered
+ */
+ res = -EEXIST;
+ if (__dev_get_by_name(net, name) != NULL)
+ goto out;
}
res = register_netdevice(bond_dev);
diff --git a/drivers/net/ehea/ehea_main.c b/drivers/net/ehea/ehea_main.c
index a333b42..6372610 100644
--- a/drivers/net/ehea/ehea_main.c
+++ b/drivers/net/ehea/ehea_main.c
@@ -533,8 +533,15 @@
int length = cqe->num_bytes_transfered - 4; /*remove CRC */
skb_put(skb, length);
- skb->ip_summed = CHECKSUM_UNNECESSARY;
skb->protocol = eth_type_trans(skb, dev);
+
+ /* The packet was not an IPV4 packet so a complemented checksum was
+ calculated. The value is found in the Internet Checksum field. */
+ if (cqe->status & EHEA_CQE_BLIND_CKSUM) {
+ skb->ip_summed = CHECKSUM_COMPLETE;
+ skb->csum = csum_unfold(~cqe->inet_checksum_value);
+ } else
+ skb->ip_summed = CHECKSUM_UNNECESSARY;
}
static inline struct sk_buff *get_skb_by_index(struct sk_buff **skb_array,
diff --git a/drivers/net/ehea/ehea_qmr.h b/drivers/net/ehea/ehea_qmr.h
index f608a6c..3810473 100644
--- a/drivers/net/ehea/ehea_qmr.h
+++ b/drivers/net/ehea/ehea_qmr.h
@@ -150,6 +150,7 @@
#define EHEA_CQE_TYPE_RQ 0x60
#define EHEA_CQE_STAT_ERR_MASK 0x700F
#define EHEA_CQE_STAT_FAT_ERR_MASK 0xF
+#define EHEA_CQE_BLIND_CKSUM 0x8000
#define EHEA_CQE_STAT_ERR_TCP 0x4000
#define EHEA_CQE_STAT_ERR_IP 0x2000
#define EHEA_CQE_STAT_ERR_CRC 0x1000
diff --git a/drivers/net/fec.c b/drivers/net/fec.c
index 768b840..cce32d4 100644
--- a/drivers/net/fec.c
+++ b/drivers/net/fec.c
@@ -678,24 +678,37 @@
{
struct fec_enet_private *fep = netdev_priv(dev);
struct phy_device *phy_dev = NULL;
- int ret;
+ char mdio_bus_id[MII_BUS_ID_SIZE];
+ char phy_name[MII_BUS_ID_SIZE + 3];
+ int phy_id;
fep->phy_dev = NULL;
- /* find the first phy */
- phy_dev = phy_find_first(fep->mii_bus);
- if (!phy_dev) {
- printk(KERN_ERR "%s: no PHY found\n", dev->name);
- return -ENODEV;
+ /* check for attached phy */
+ for (phy_id = 0; (phy_id < PHY_MAX_ADDR); phy_id++) {
+ if ((fep->mii_bus->phy_mask & (1 << phy_id)))
+ continue;
+ if (fep->mii_bus->phy_map[phy_id] == NULL)
+ continue;
+ if (fep->mii_bus->phy_map[phy_id]->phy_id == 0)
+ continue;
+ strncpy(mdio_bus_id, fep->mii_bus->id, MII_BUS_ID_SIZE);
+ break;
}
- /* attach the mac to the phy */
- ret = phy_connect_direct(dev, phy_dev,
- &fec_enet_adjust_link, 0,
- PHY_INTERFACE_MODE_MII);
- if (ret) {
- printk(KERN_ERR "%s: Could not attach to PHY\n", dev->name);
- return ret;
+ if (phy_id >= PHY_MAX_ADDR) {
+ printk(KERN_INFO "%s: no PHY, assuming direct connection "
+ "to switch\n", dev->name);
+ strncpy(mdio_bus_id, "0", MII_BUS_ID_SIZE);
+ phy_id = 0;
+ }
+
+ snprintf(phy_name, MII_BUS_ID_SIZE, PHY_ID_FMT, mdio_bus_id, phy_id);
+ phy_dev = phy_connect(dev, phy_name, &fec_enet_adjust_link, 0,
+ PHY_INTERFACE_MODE_MII);
+ if (IS_ERR(phy_dev)) {
+ printk(KERN_ERR "%s: could not attach to PHY\n", dev->name);
+ return PTR_ERR(phy_dev);
}
/* mask with MAC supported features */
@@ -738,7 +751,7 @@
fep->mii_bus->read = fec_enet_mdio_read;
fep->mii_bus->write = fec_enet_mdio_write;
fep->mii_bus->reset = fec_enet_mdio_reset;
- snprintf(fep->mii_bus->id, MII_BUS_ID_SIZE, "%x", pdev->id);
+ snprintf(fep->mii_bus->id, MII_BUS_ID_SIZE, "%x", pdev->id + 1);
fep->mii_bus->priv = fep;
fep->mii_bus->parent = &pdev->dev;
@@ -1311,6 +1324,9 @@
if (ret)
goto failed_mii_init;
+ /* Carrier starts down, phylib will bring it up */
+ netif_carrier_off(ndev);
+
ret = register_netdev(ndev);
if (ret)
goto failed_register;
diff --git a/drivers/net/r8169.c b/drivers/net/r8169.c
index a0da4a1..992db2f 100644
--- a/drivers/net/r8169.c
+++ b/drivers/net/r8169.c
@@ -1212,7 +1212,8 @@
if ((RTL_R8(ChipCmd) & CmdRxEnb) == 0)
return;
- counters = pci_alloc_consistent(tp->pci_dev, sizeof(*counters), &paddr);
+ counters = dma_alloc_coherent(&tp->pci_dev->dev, sizeof(*counters),
+ &paddr, GFP_KERNEL);
if (!counters)
return;
@@ -1233,7 +1234,8 @@
RTL_W32(CounterAddrLow, 0);
RTL_W32(CounterAddrHigh, 0);
- pci_free_consistent(tp->pci_dev, sizeof(*counters), counters, paddr);
+ dma_free_coherent(&tp->pci_dev->dev, sizeof(*counters), counters,
+ paddr);
}
static void rtl8169_get_ethtool_stats(struct net_device *dev,
@@ -3292,15 +3294,15 @@
/*
* Rx and Tx desscriptors needs 256 bytes alignment.
- * pci_alloc_consistent provides more.
+ * dma_alloc_coherent provides more.
*/
- tp->TxDescArray = pci_alloc_consistent(pdev, R8169_TX_RING_BYTES,
- &tp->TxPhyAddr);
+ tp->TxDescArray = dma_alloc_coherent(&pdev->dev, R8169_TX_RING_BYTES,
+ &tp->TxPhyAddr, GFP_KERNEL);
if (!tp->TxDescArray)
goto err_pm_runtime_put;
- tp->RxDescArray = pci_alloc_consistent(pdev, R8169_RX_RING_BYTES,
- &tp->RxPhyAddr);
+ tp->RxDescArray = dma_alloc_coherent(&pdev->dev, R8169_RX_RING_BYTES,
+ &tp->RxPhyAddr, GFP_KERNEL);
if (!tp->RxDescArray)
goto err_free_tx_0;
@@ -3334,12 +3336,12 @@
err_release_ring_2:
rtl8169_rx_clear(tp);
err_free_rx_1:
- pci_free_consistent(pdev, R8169_RX_RING_BYTES, tp->RxDescArray,
- tp->RxPhyAddr);
+ dma_free_coherent(&pdev->dev, R8169_RX_RING_BYTES, tp->RxDescArray,
+ tp->RxPhyAddr);
tp->RxDescArray = NULL;
err_free_tx_0:
- pci_free_consistent(pdev, R8169_TX_RING_BYTES, tp->TxDescArray,
- tp->TxPhyAddr);
+ dma_free_coherent(&pdev->dev, R8169_TX_RING_BYTES, tp->TxDescArray,
+ tp->TxPhyAddr);
tp->TxDescArray = NULL;
err_pm_runtime_put:
pm_runtime_put_noidle(&pdev->dev);
@@ -3975,7 +3977,7 @@
{
struct pci_dev *pdev = tp->pci_dev;
- pci_unmap_single(pdev, le64_to_cpu(desc->addr), tp->rx_buf_sz,
+ dma_unmap_single(&pdev->dev, le64_to_cpu(desc->addr), tp->rx_buf_sz,
PCI_DMA_FROMDEVICE);
dev_kfree_skb(*sk_buff);
*sk_buff = NULL;
@@ -4000,7 +4002,7 @@
static struct sk_buff *rtl8169_alloc_rx_skb(struct pci_dev *pdev,
struct net_device *dev,
struct RxDesc *desc, int rx_buf_sz,
- unsigned int align)
+ unsigned int align, gfp_t gfp)
{
struct sk_buff *skb;
dma_addr_t mapping;
@@ -4008,13 +4010,13 @@
pad = align ? align : NET_IP_ALIGN;
- skb = netdev_alloc_skb(dev, rx_buf_sz + pad);
+ skb = __netdev_alloc_skb(dev, rx_buf_sz + pad, gfp);
if (!skb)
goto err_out;
skb_reserve(skb, align ? ((pad - 1) & (unsigned long)skb->data) : pad);
- mapping = pci_map_single(pdev, skb->data, rx_buf_sz,
+ mapping = dma_map_single(&pdev->dev, skb->data, rx_buf_sz,
PCI_DMA_FROMDEVICE);
rtl8169_map_to_asic(desc, mapping, rx_buf_sz);
@@ -4039,7 +4041,7 @@
}
static u32 rtl8169_rx_fill(struct rtl8169_private *tp, struct net_device *dev,
- u32 start, u32 end)
+ u32 start, u32 end, gfp_t gfp)
{
u32 cur;
@@ -4054,7 +4056,7 @@
skb = rtl8169_alloc_rx_skb(tp->pci_dev, dev,
tp->RxDescArray + i,
- tp->rx_buf_sz, tp->align);
+ tp->rx_buf_sz, tp->align, gfp);
if (!skb)
break;
@@ -4082,7 +4084,7 @@
memset(tp->tx_skb, 0x0, NUM_TX_DESC * sizeof(struct ring_info));
memset(tp->Rx_skbuff, 0x0, NUM_RX_DESC * sizeof(struct sk_buff *));
- if (rtl8169_rx_fill(tp, dev, 0, NUM_RX_DESC) != NUM_RX_DESC)
+ if (rtl8169_rx_fill(tp, dev, 0, NUM_RX_DESC, GFP_KERNEL) != NUM_RX_DESC)
goto err_out;
rtl8169_mark_as_last_descriptor(tp->RxDescArray + NUM_RX_DESC - 1);
@@ -4099,7 +4101,8 @@
{
unsigned int len = tx_skb->len;
- pci_unmap_single(pdev, le64_to_cpu(desc->addr), len, PCI_DMA_TODEVICE);
+ dma_unmap_single(&pdev->dev, le64_to_cpu(desc->addr), len,
+ PCI_DMA_TODEVICE);
desc->opts1 = 0x00;
desc->opts2 = 0x00;
desc->addr = 0x00;
@@ -4243,7 +4246,8 @@
txd = tp->TxDescArray + entry;
len = frag->size;
addr = ((void *) page_address(frag->page)) + frag->page_offset;
- mapping = pci_map_single(tp->pci_dev, addr, len, PCI_DMA_TODEVICE);
+ mapping = dma_map_single(&tp->pci_dev->dev, addr, len,
+ PCI_DMA_TODEVICE);
/* anti gcc 2.95.3 bugware (sic) */
status = opts1 | len | (RingEnd * !((entry + 1) % NUM_TX_DESC));
@@ -4313,7 +4317,8 @@
tp->tx_skb[entry].skb = skb;
}
- mapping = pci_map_single(tp->pci_dev, skb->data, len, PCI_DMA_TODEVICE);
+ mapping = dma_map_single(&tp->pci_dev->dev, skb->data, len,
+ PCI_DMA_TODEVICE);
tp->tx_skb[entry].len = len;
txd->addr = cpu_to_le64(mapping);
@@ -4477,8 +4482,8 @@
if (!skb)
goto out;
- pci_dma_sync_single_for_cpu(tp->pci_dev, addr, pkt_size,
- PCI_DMA_FROMDEVICE);
+ dma_sync_single_for_cpu(&tp->pci_dev->dev, addr, pkt_size,
+ PCI_DMA_FROMDEVICE);
skb_copy_from_linear_data(*sk_buff, skb->data, pkt_size);
*sk_buff = skb;
done = true;
@@ -4549,11 +4554,11 @@
rtl8169_rx_csum(skb, desc);
if (rtl8169_try_rx_copy(&skb, tp, pkt_size, addr)) {
- pci_dma_sync_single_for_device(pdev, addr,
+ dma_sync_single_for_device(&pdev->dev, addr,
pkt_size, PCI_DMA_FROMDEVICE);
rtl8169_mark_to_asic(desc, tp->rx_buf_sz);
} else {
- pci_unmap_single(pdev, addr, tp->rx_buf_sz,
+ dma_unmap_single(&pdev->dev, addr, tp->rx_buf_sz,
PCI_DMA_FROMDEVICE);
tp->Rx_skbuff[entry] = NULL;
}
@@ -4583,7 +4588,7 @@
count = cur_rx - tp->cur_rx;
tp->cur_rx = cur_rx;
- delta = rtl8169_rx_fill(tp, dev, tp->dirty_rx, tp->cur_rx);
+ delta = rtl8169_rx_fill(tp, dev, tp->dirty_rx, tp->cur_rx, GFP_ATOMIC);
if (!delta && count)
netif_info(tp, intr, dev, "no Rx buffer allocated\n");
tp->dirty_rx += delta;
@@ -4769,10 +4774,10 @@
free_irq(dev->irq, dev);
- pci_free_consistent(pdev, R8169_RX_RING_BYTES, tp->RxDescArray,
- tp->RxPhyAddr);
- pci_free_consistent(pdev, R8169_TX_RING_BYTES, tp->TxDescArray,
- tp->TxPhyAddr);
+ dma_free_coherent(&pdev->dev, R8169_RX_RING_BYTES, tp->RxDescArray,
+ tp->RxPhyAddr);
+ dma_free_coherent(&pdev->dev, R8169_TX_RING_BYTES, tp->TxDescArray,
+ tp->TxPhyAddr);
tp->TxDescArray = NULL;
tp->RxDescArray = NULL;
diff --git a/drivers/net/skge.c b/drivers/net/skge.c
index 40e5c46..465ae7e 100644
--- a/drivers/net/skge.c
+++ b/drivers/net/skge.c
@@ -43,6 +43,7 @@
#include <linux/seq_file.h>
#include <linux/mii.h>
#include <linux/slab.h>
+#include <linux/dmi.h>
#include <asm/irq.h>
#include "skge.h"
@@ -3868,6 +3869,8 @@
netif_info(skge, probe, skge->netdev, "addr %pM\n", dev->dev_addr);
}
+static int only_32bit_dma;
+
static int __devinit skge_probe(struct pci_dev *pdev,
const struct pci_device_id *ent)
{
@@ -3889,7 +3892,7 @@
pci_set_master(pdev);
- if (!pci_set_dma_mask(pdev, DMA_BIT_MASK(64))) {
+ if (!only_32bit_dma && !pci_set_dma_mask(pdev, DMA_BIT_MASK(64))) {
using_dac = 1;
err = pci_set_consistent_dma_mask(pdev, DMA_BIT_MASK(64));
} else if (!(err = pci_set_dma_mask(pdev, DMA_BIT_MASK(32)))) {
@@ -4147,8 +4150,21 @@
.shutdown = skge_shutdown,
};
+static struct dmi_system_id skge_32bit_dma_boards[] = {
+ {
+ .ident = "Gigabyte nForce boards",
+ .matches = {
+ DMI_MATCH(DMI_BOARD_VENDOR, "Gigabyte Technology Co"),
+ DMI_MATCH(DMI_BOARD_NAME, "nForce"),
+ },
+ },
+ {}
+};
+
static int __init skge_init_module(void)
{
+ if (dmi_check_system(skge_32bit_dma_boards))
+ only_32bit_dma = 1;
skge_debug_init();
return pci_register_driver(&skge_driver);
}
diff --git a/drivers/net/tg3.c b/drivers/net/tg3.c
index bc3af78..1ec4b9e 100644
--- a/drivers/net/tg3.c
+++ b/drivers/net/tg3.c
@@ -4666,7 +4666,7 @@
desc_idx, *post_ptr);
drop_it_no_recycle:
/* Other statistics kept track of by card. */
- tp->net_stats.rx_dropped++;
+ tp->rx_dropped++;
goto next_pkt;
}
@@ -4726,7 +4726,7 @@
if (len > (tp->dev->mtu + ETH_HLEN) &&
skb->protocol != htons(ETH_P_8021Q)) {
dev_kfree_skb(skb);
- goto next_pkt;
+ goto drop_it_no_recycle;
}
if (desc->type_flags & RXD_FLAG_VLAN &&
@@ -9240,6 +9240,8 @@
stats->rx_missed_errors = old_stats->rx_missed_errors +
get_stat64(&hw_stats->rx_discards);
+ stats->rx_dropped = tp->rx_dropped;
+
return stats;
}
diff --git a/drivers/net/tg3.h b/drivers/net/tg3.h
index 4937bd1..be7ff13 100644
--- a/drivers/net/tg3.h
+++ b/drivers/net/tg3.h
@@ -2759,7 +2759,7 @@
/* begin "everything else" cacheline(s) section */
- struct rtnl_link_stats64 net_stats;
+ unsigned long rx_dropped;
struct rtnl_link_stats64 net_stats_prev;
struct tg3_ethtool_stats estats;
struct tg3_ethtool_stats estats_prev;
diff --git a/drivers/net/wimax/i2400m/rx.c b/drivers/net/wimax/i2400m/rx.c
index 8cc9e31..1737d14 100644
--- a/drivers/net/wimax/i2400m/rx.c
+++ b/drivers/net/wimax/i2400m/rx.c
@@ -1244,16 +1244,16 @@
int i, result;
struct device *dev = i2400m_dev(i2400m);
const struct i2400m_msg_hdr *msg_hdr;
- size_t pl_itr, pl_size, skb_len;
+ size_t pl_itr, pl_size;
unsigned long flags;
- unsigned num_pls, single_last;
+ unsigned num_pls, single_last, skb_len;
skb_len = skb->len;
- d_fnstart(4, dev, "(i2400m %p skb %p [size %zu])\n",
+ d_fnstart(4, dev, "(i2400m %p skb %p [size %u])\n",
i2400m, skb, skb_len);
result = -EIO;
msg_hdr = (void *) skb->data;
- result = i2400m_rx_msg_hdr_check(i2400m, msg_hdr, skb->len);
+ result = i2400m_rx_msg_hdr_check(i2400m, msg_hdr, skb_len);
if (result < 0)
goto error_msg_hdr_check;
result = -EIO;
@@ -1261,10 +1261,10 @@
pl_itr = sizeof(*msg_hdr) + /* Check payload descriptor(s) */
num_pls * sizeof(msg_hdr->pld[0]);
pl_itr = ALIGN(pl_itr, I2400M_PL_ALIGN);
- if (pl_itr > skb->len) { /* got all the payload descriptors? */
+ if (pl_itr > skb_len) { /* got all the payload descriptors? */
dev_err(dev, "RX: HW BUG? message too short (%u bytes) for "
"%u payload descriptors (%zu each, total %zu)\n",
- skb->len, num_pls, sizeof(msg_hdr->pld[0]), pl_itr);
+ skb_len, num_pls, sizeof(msg_hdr->pld[0]), pl_itr);
goto error_pl_descr_short;
}
/* Walk each payload payload--check we really got it */
@@ -1272,7 +1272,7 @@
/* work around old gcc warnings */
pl_size = i2400m_pld_size(&msg_hdr->pld[i]);
result = i2400m_rx_pl_descr_check(i2400m, &msg_hdr->pld[i],
- pl_itr, skb->len);
+ pl_itr, skb_len);
if (result < 0)
goto error_pl_descr_check;
single_last = num_pls == 1 || i == num_pls - 1;
@@ -1290,16 +1290,16 @@
if (i < i2400m->rx_pl_min)
i2400m->rx_pl_min = i;
i2400m->rx_num++;
- i2400m->rx_size_acc += skb->len;
- if (skb->len < i2400m->rx_size_min)
- i2400m->rx_size_min = skb->len;
- if (skb->len > i2400m->rx_size_max)
- i2400m->rx_size_max = skb->len;
+ i2400m->rx_size_acc += skb_len;
+ if (skb_len < i2400m->rx_size_min)
+ i2400m->rx_size_min = skb_len;
+ if (skb_len > i2400m->rx_size_max)
+ i2400m->rx_size_max = skb_len;
spin_unlock_irqrestore(&i2400m->rx_lock, flags);
error_pl_descr_check:
error_pl_descr_short:
error_msg_hdr_check:
- d_fnend(4, dev, "(i2400m %p skb %p [size %zu]) = %d\n",
+ d_fnend(4, dev, "(i2400m %p skb %p [size %u]) = %d\n",
i2400m, skb, skb_len, result);
return result;
}
diff --git a/drivers/net/wireless/ath/ath9k/ani.c b/drivers/net/wireless/ath/ath9k/ani.c
index cc648b6..a3d95cc 100644
--- a/drivers/net/wireless/ath/ath9k/ani.c
+++ b/drivers/net/wireless/ath/ath9k/ani.c
@@ -543,7 +543,7 @@
if (conf_is_ht40(conf))
return clockrate * 2;
- return clockrate * 2;
+ return clockrate;
}
static int32_t ath9k_hw_ani_get_listen_time(struct ath_hw *ah)
diff --git a/drivers/net/wireless/iwlwifi/iwl-agn-lib.c b/drivers/net/wireless/iwlwifi/iwl-agn-lib.c
index 9dd9e64..8fd00a6 100644
--- a/drivers/net/wireless/iwlwifi/iwl-agn-lib.c
+++ b/drivers/net/wireless/iwlwifi/iwl-agn-lib.c
@@ -1411,7 +1411,7 @@
clear_bit(STATUS_SCAN_HW, &priv->status);
clear_bit(STATUS_SCANNING, &priv->status);
/* inform mac80211 scan aborted */
- queue_work(priv->workqueue, &priv->scan_completed);
+ queue_work(priv->workqueue, &priv->abort_scan);
}
int iwlagn_manage_ibss_station(struct iwl_priv *priv,
diff --git a/drivers/net/wireless/iwlwifi/iwl3945-base.c b/drivers/net/wireless/iwlwifi/iwl3945-base.c
index 59a308b..d31661c 100644
--- a/drivers/net/wireless/iwlwifi/iwl3945-base.c
+++ b/drivers/net/wireless/iwlwifi/iwl3945-base.c
@@ -3018,7 +3018,7 @@
clear_bit(STATUS_SCANNING, &priv->status);
/* inform mac80211 scan aborted */
- queue_work(priv->workqueue, &priv->scan_completed);
+ queue_work(priv->workqueue, &priv->abort_scan);
}
static void iwl3945_bg_restart(struct work_struct *data)
diff --git a/drivers/platform/x86/intel_ips.c b/drivers/platform/x86/intel_ips.c
index 9024480a..c44a5e8 100644
--- a/drivers/platform/x86/intel_ips.c
+++ b/drivers/platform/x86/intel_ips.c
@@ -51,7 +51,6 @@
* TODO:
* - handle CPU hotplug
* - provide turbo enable/disable api
- * - make sure we can write turbo enable/disable reg based on MISC_EN
*
* Related documents:
* - CDI 403777, 403778 - Auburndale EDS vol 1 & 2
@@ -230,7 +229,7 @@
#define THM_TC2 0xac
#define THM_DTV 0xb0
#define THM_ITV 0xd8
-#define ITV_ME_SEQNO_MASK 0x000f0000 /* ME should update every ~200ms */
+#define ITV_ME_SEQNO_MASK 0x00ff0000 /* ME should update every ~200ms */
#define ITV_ME_SEQNO_SHIFT (16)
#define ITV_MCH_TEMP_MASK 0x0000ff00
#define ITV_MCH_TEMP_SHIFT (8)
@@ -325,6 +324,7 @@
bool gpu_preferred;
bool poll_turbo_status;
bool second_cpu;
+ bool turbo_toggle_allowed;
struct ips_mcp_limits *limits;
/* Optional MCH interfaces for if i915 is in use */
@@ -415,7 +415,7 @@
new_limit = cur_limit - 8; /* 1W decrease */
/* Clamp to SKU TDP limit */
- if (((new_limit * 10) / 8) < (ips->orig_turbo_limit & TURBO_TDP_MASK))
+ if (new_limit < (ips->orig_turbo_limit & TURBO_TDP_MASK))
new_limit = ips->orig_turbo_limit & TURBO_TDP_MASK;
thm_writew(THM_MPCPC, (new_limit * 10) / 8);
@@ -461,7 +461,8 @@
if (ips->__cpu_turbo_on)
return;
- on_each_cpu(do_enable_cpu_turbo, ips, 1);
+ if (ips->turbo_toggle_allowed)
+ on_each_cpu(do_enable_cpu_turbo, ips, 1);
ips->__cpu_turbo_on = true;
}
@@ -498,7 +499,8 @@
if (!ips->__cpu_turbo_on)
return;
- on_each_cpu(do_disable_cpu_turbo, ips, 1);
+ if (ips->turbo_toggle_allowed)
+ on_each_cpu(do_disable_cpu_turbo, ips, 1);
ips->__cpu_turbo_on = false;
}
@@ -598,17 +600,29 @@
{
unsigned long flags;
bool ret = false;
+ u32 temp_limit;
+ u32 avg_power;
+ const char *msg = "MCP limit exceeded: ";
spin_lock_irqsave(&ips->turbo_status_lock, flags);
- if (ips->mcp_avg_temp > (ips->mcp_temp_limit * 100))
- ret = true;
- if (ips->cpu_avg_power + ips->mch_avg_power > ips->mcp_power_limit)
- ret = true;
- spin_unlock_irqrestore(&ips->turbo_status_lock, flags);
- if (ret)
+ temp_limit = ips->mcp_temp_limit * 100;
+ if (ips->mcp_avg_temp > temp_limit) {
dev_info(&ips->dev->dev,
- "MCP power or thermal limit exceeded\n");
+ "%sAvg temp %u, limit %u\n", msg, ips->mcp_avg_temp,
+ temp_limit);
+ ret = true;
+ }
+
+ avg_power = ips->cpu_avg_power + ips->mch_avg_power;
+ if (avg_power > ips->mcp_power_limit) {
+ dev_info(&ips->dev->dev,
+ "%sAvg power %u, limit %u\n", msg, avg_power,
+ ips->mcp_power_limit);
+ ret = true;
+ }
+
+ spin_unlock_irqrestore(&ips->turbo_status_lock, flags);
return ret;
}
@@ -663,6 +677,27 @@
}
/**
+ * verify_limits - verify BIOS provided limits
+ * @ips: IPS structure
+ *
+ * BIOS can optionally provide non-default limits for power and temp. Check
+ * them here and use the defaults if the BIOS values are not provided or
+ * are otherwise unusable.
+ */
+static void verify_limits(struct ips_driver *ips)
+{
+ if (ips->mcp_power_limit < ips->limits->mcp_power_limit ||
+ ips->mcp_power_limit > 35000)
+ ips->mcp_power_limit = ips->limits->mcp_power_limit;
+
+ if (ips->mcp_temp_limit < ips->limits->core_temp_limit ||
+ ips->mcp_temp_limit < ips->limits->mch_temp_limit ||
+ ips->mcp_temp_limit > 150)
+ ips->mcp_temp_limit = min(ips->limits->core_temp_limit,
+ ips->limits->mch_temp_limit);
+}
+
+/**
* update_turbo_limits - get various limits & settings from regs
* @ips: IPS driver struct
*
@@ -680,12 +715,21 @@
u32 hts = thm_readl(THM_HTS);
ips->cpu_turbo_enabled = !(hts & HTS_PCTD_DIS);
- ips->gpu_turbo_enabled = !(hts & HTS_GTD_DIS);
+ /*
+ * Disable turbo for now, until we can figure out why the power figures
+ * are wrong
+ */
+ ips->cpu_turbo_enabled = false;
+
+ if (ips->gpu_busy)
+ ips->gpu_turbo_enabled = !(hts & HTS_GTD_DIS);
+
ips->core_power_limit = thm_readw(THM_MPCPC);
ips->mch_power_limit = thm_readw(THM_MMGPC);
ips->mcp_temp_limit = thm_readw(THM_PTL);
ips->mcp_power_limit = thm_readw(THM_MPPC);
+ verify_limits(ips);
/* Ignore BIOS CPU vs GPU pref */
}
@@ -858,7 +902,7 @@
ret = (ret * 1000) / 65535;
*last = val;
- return ret;
+ return 0;
}
static const u16 temp_decay_factor = 2;
@@ -940,7 +984,6 @@
kfree(mch_samples);
kfree(cpu_samples);
kfree(mchp_samples);
- kthread_stop(ips->adjust);
return -ENOMEM;
}
@@ -948,7 +991,7 @@
ITV_ME_SEQNO_SHIFT;
seqno_timestamp = get_jiffies_64();
- old_cpu_power = thm_readl(THM_CEC) / 65535;
+ old_cpu_power = thm_readl(THM_CEC);
schedule_timeout_interruptible(msecs_to_jiffies(IPS_SAMPLE_PERIOD));
/* Collect an initial average */
@@ -1150,11 +1193,18 @@
STS_GPL_SHIFT;
/* ignore EC CPU vs GPU pref */
ips->cpu_turbo_enabled = !(sts & STS_PCTD_DIS);
- ips->gpu_turbo_enabled = !(sts & STS_GTD_DIS);
+ /*
+ * Disable turbo for now, until we can figure
+ * out why the power figures are wrong
+ */
+ ips->cpu_turbo_enabled = false;
+ if (ips->gpu_busy)
+ ips->gpu_turbo_enabled = !(sts & STS_GTD_DIS);
ips->mcp_temp_limit = (sts & STS_PTL_MASK) >>
STS_PTL_SHIFT;
ips->mcp_power_limit = (tc1 & STS_PPL_MASK) >>
STS_PPL_SHIFT;
+ verify_limits(ips);
spin_unlock(&ips->turbo_status_lock);
thm_writeb(THM_SEC, SEC_ACK);
@@ -1333,8 +1383,10 @@
* turbo manually or we'll get an illegal MSR access, even though
* turbo will still be available.
*/
- if (!(misc_en & IA32_MISC_TURBO_EN))
- ; /* add turbo MSR write allowed flag if necessary */
+ if (misc_en & IA32_MISC_TURBO_EN)
+ ips->turbo_toggle_allowed = true;
+ else
+ ips->turbo_toggle_allowed = false;
if (strstr(boot_cpu_data.x86_model_id, "CPU M"))
limits = &ips_sv_limits;
@@ -1351,9 +1403,10 @@
tdp = turbo_power & TURBO_TDP_MASK;
/* Sanity check TDP against CPU */
- if (limits->mcp_power_limit != (tdp / 8) * 1000) {
- dev_warn(&ips->dev->dev, "Warning: CPU TDP doesn't match expected value (found %d, expected %d)\n",
- tdp / 8, limits->mcp_power_limit / 1000);
+ if (limits->core_power_limit != (tdp / 8) * 1000) {
+ dev_info(&ips->dev->dev, "CPU TDP doesn't match expected value (found %d, expected %d)\n",
+ tdp / 8, limits->core_power_limit / 1000);
+ limits->core_power_limit = (tdp / 8) * 1000;
}
out:
@@ -1390,7 +1443,7 @@
return true;
out_put_busy:
- symbol_put(i915_gpu_turbo_disable);
+ symbol_put(i915_gpu_busy);
out_put_lower:
symbol_put(i915_gpu_lower);
out_put_raise:
@@ -1532,23 +1585,28 @@
/* Save turbo limits & ratios */
rdmsrl(TURBO_POWER_CURRENT_LIMIT, ips->orig_turbo_limit);
- ips_enable_cpu_turbo(ips);
- ips->cpu_turbo_enabled = true;
+ ips_disable_cpu_turbo(ips);
+ ips->cpu_turbo_enabled = false;
- /* Set up the work queue and monitor/adjust threads */
- ips->monitor = kthread_run(ips_monitor, ips, "ips-monitor");
- if (IS_ERR(ips->monitor)) {
- dev_err(&dev->dev,
- "failed to create thermal monitor thread, aborting\n");
- ret = -ENOMEM;
- goto error_free_irq;
- }
-
+ /* Create thermal adjust thread */
ips->adjust = kthread_create(ips_adjust, ips, "ips-adjust");
if (IS_ERR(ips->adjust)) {
dev_err(&dev->dev,
"failed to create thermal adjust thread, aborting\n");
ret = -ENOMEM;
+ goto error_free_irq;
+
+ }
+
+ /*
+ * Set up the work queue and monitor thread. The monitor thread
+ * will wake up ips_adjust thread.
+ */
+ ips->monitor = kthread_run(ips_monitor, ips, "ips-monitor");
+ if (IS_ERR(ips->monitor)) {
+ dev_err(&dev->dev,
+ "failed to create thermal monitor thread, aborting\n");
+ ret = -ENOMEM;
goto error_thread_cleanup;
}
@@ -1566,7 +1624,7 @@
return ret;
error_thread_cleanup:
- kthread_stop(ips->monitor);
+ kthread_stop(ips->adjust);
error_free_irq:
free_irq(ips->dev->irq, ips);
error_unmap:
diff --git a/drivers/regulator/ad5398.c b/drivers/regulator/ad5398.c
index df1fb53..a4be416 100644
--- a/drivers/regulator/ad5398.c
+++ b/drivers/regulator/ad5398.c
@@ -256,7 +256,6 @@
regulator_unregister(chip->rdev);
kfree(chip);
- i2c_set_clientdata(client, NULL);
return 0;
}
diff --git a/drivers/regulator/core.c b/drivers/regulator/core.c
index 422a709..cc8b337 100644
--- a/drivers/regulator/core.c
+++ b/drivers/regulator/core.c
@@ -700,7 +700,7 @@
constraints->min_uA != constraints->max_uA) {
ret = _regulator_get_current_limit(rdev);
if (ret > 0)
- count += sprintf(buf + count, "at %d uA ", ret / 1000);
+ count += sprintf(buf + count, "at %d mA ", ret / 1000);
}
if (constraints->valid_modes_mask & REGULATOR_MODE_FAST)
@@ -2302,8 +2302,10 @@
dev_set_name(&rdev->dev, "regulator.%d",
atomic_inc_return(®ulator_no) - 1);
ret = device_register(&rdev->dev);
- if (ret != 0)
+ if (ret != 0) {
+ put_device(&rdev->dev);
goto clean;
+ }
dev_set_drvdata(&rdev->dev, rdev);
diff --git a/drivers/regulator/isl6271a-regulator.c b/drivers/regulator/isl6271a-regulator.c
index d61ecb8..b8cc638 100644
--- a/drivers/regulator/isl6271a-regulator.c
+++ b/drivers/regulator/isl6271a-regulator.c
@@ -191,8 +191,6 @@
struct isl_pmic *pmic = i2c_get_clientdata(i2c);
int i;
- i2c_set_clientdata(i2c, NULL);
-
for (i = 0; i < 3; i++)
regulator_unregister(pmic->rdev[i]);
diff --git a/drivers/regulator/max8649.c b/drivers/regulator/max8649.c
index 4520ace..6b60a9c 100644
--- a/drivers/regulator/max8649.c
+++ b/drivers/regulator/max8649.c
@@ -330,7 +330,7 @@
/* set external clock frequency */
info->extclk_freq = pdata->extclk_freq;
max8649_set_bits(info->i2c, MAX8649_SYNC, MAX8649_EXT_MASK,
- info->extclk_freq);
+ info->extclk_freq << 6);
}
if (pdata->ramp_timing) {
diff --git a/drivers/rtc/rtc-ds3232.c b/drivers/rtc/rtc-ds3232.c
index 9daed8d..9de8516 100644
--- a/drivers/rtc/rtc-ds3232.c
+++ b/drivers/rtc/rtc-ds3232.c
@@ -268,7 +268,6 @@
free_irq(client->irq, client);
out_free:
- i2c_set_clientdata(client, NULL);
kfree(ds3232);
return ret;
}
@@ -287,7 +286,6 @@
}
rtc_device_unregister(ds3232->rtc);
- i2c_set_clientdata(client, NULL);
kfree(ds3232);
return 0;
}
diff --git a/drivers/spi/spi.c b/drivers/spi/spi.c
index 0bcf4c1..b5a78a1 100644
--- a/drivers/spi/spi.c
+++ b/drivers/spi/spi.c
@@ -23,6 +23,7 @@
#include <linux/init.h>
#include <linux/cache.h>
#include <linux/mutex.h>
+#include <linux/of_device.h>
#include <linux/slab.h>
#include <linux/mod_devicetable.h>
#include <linux/spi/spi.h>
@@ -86,6 +87,10 @@
const struct spi_device *spi = to_spi_device(dev);
const struct spi_driver *sdrv = to_spi_driver(drv);
+ /* Attempt an OF style match */
+ if (of_driver_match_device(dev, drv))
+ return 1;
+
if (sdrv->id_table)
return !!spi_match_id(sdrv->id_table, spi);
diff --git a/drivers/spi/spi_gpio.c b/drivers/spi/spi_gpio.c
index e24a634..63e51b0 100644
--- a/drivers/spi/spi_gpio.c
+++ b/drivers/spi/spi_gpio.c
@@ -350,7 +350,7 @@
spi_gpio->bitbang.master = spi_master_get(master);
spi_gpio->bitbang.chipselect = spi_gpio_chipselect;
- if ((master_flags & (SPI_MASTER_NO_RX | SPI_MASTER_NO_RX)) == 0) {
+ if ((master_flags & (SPI_MASTER_NO_TX | SPI_MASTER_NO_RX)) == 0) {
spi_gpio->bitbang.txrx_word[SPI_MODE_0] = spi_gpio_txrx_word_mode0;
spi_gpio->bitbang.txrx_word[SPI_MODE_1] = spi_gpio_txrx_word_mode1;
spi_gpio->bitbang.txrx_word[SPI_MODE_2] = spi_gpio_txrx_word_mode2;
diff --git a/drivers/spi/spi_mpc8xxx.c b/drivers/spi/spi_mpc8xxx.c
index d31b57f..1dd86b8 100644
--- a/drivers/spi/spi_mpc8xxx.c
+++ b/drivers/spi/spi_mpc8xxx.c
@@ -408,11 +408,17 @@
xfer_ofs = mspi->xfer_in_progress->len - mspi->count;
- out_be32(&rx_bd->cbd_bufaddr, mspi->rx_dma + xfer_ofs);
+ if (mspi->rx_dma == mspi->dma_dummy_rx)
+ out_be32(&rx_bd->cbd_bufaddr, mspi->rx_dma);
+ else
+ out_be32(&rx_bd->cbd_bufaddr, mspi->rx_dma + xfer_ofs);
out_be16(&rx_bd->cbd_datlen, 0);
out_be16(&rx_bd->cbd_sc, BD_SC_EMPTY | BD_SC_INTRPT | BD_SC_WRAP);
- out_be32(&tx_bd->cbd_bufaddr, mspi->tx_dma + xfer_ofs);
+ if (mspi->tx_dma == mspi->dma_dummy_tx)
+ out_be32(&tx_bd->cbd_bufaddr, mspi->tx_dma);
+ else
+ out_be32(&tx_bd->cbd_bufaddr, mspi->tx_dma + xfer_ofs);
out_be16(&tx_bd->cbd_datlen, xfer_len);
out_be16(&tx_bd->cbd_sc, BD_SC_READY | BD_SC_INTRPT | BD_SC_WRAP |
BD_SC_LAST);
diff --git a/drivers/staging/tm6000/Kconfig b/drivers/staging/tm6000/Kconfig
index c725356..de7ebb9 100644
--- a/drivers/staging/tm6000/Kconfig
+++ b/drivers/staging/tm6000/Kconfig
@@ -1,6 +1,6 @@
config VIDEO_TM6000
tristate "TV Master TM5600/6000/6010 driver"
- depends on VIDEO_DEV && I2C && INPUT && USB && EXPERIMENTAL
+ depends on VIDEO_DEV && I2C && INPUT && IR_CORE && USB && EXPERIMENTAL
select VIDEO_TUNER
select MEDIA_TUNER_XC2028
select MEDIA_TUNER_XC5000
diff --git a/drivers/staging/tm6000/tm6000-input.c b/drivers/staging/tm6000/tm6000-input.c
index 32f7a0a..54f7667 100644
--- a/drivers/staging/tm6000/tm6000-input.c
+++ b/drivers/staging/tm6000/tm6000-input.c
@@ -46,7 +46,7 @@
}
struct tm6000_ir_poll_result {
- u8 rc_data[4];
+ u16 rc_data;
};
struct tm6000_IR {
@@ -60,9 +60,9 @@
int polling;
struct delayed_work work;
u8 wait:1;
+ u8 key:1;
struct urb *int_urb;
u8 *urb_data;
- u8 key:1;
int (*get_key) (struct tm6000_IR *, struct tm6000_ir_poll_result *);
@@ -122,13 +122,14 @@
if (urb->status != 0)
printk(KERN_INFO "not ready\n");
- else if (urb->actual_length > 0)
+ else if (urb->actual_length > 0) {
memcpy(ir->urb_data, urb->transfer_buffer, urb->actual_length);
- dprintk("data %02x %02x %02x %02x\n", ir->urb_data[0],
- ir->urb_data[1], ir->urb_data[2], ir->urb_data[3]);
+ dprintk("data %02x %02x %02x %02x\n", ir->urb_data[0],
+ ir->urb_data[1], ir->urb_data[2], ir->urb_data[3]);
- ir->key = 1;
+ ir->key = 1;
+ }
rc = usb_submit_urb(urb, GFP_ATOMIC);
}
@@ -140,30 +141,47 @@
int rc;
u8 buf[2];
- if (ir->wait && !&dev->int_in) {
- poll_result->rc_data[0] = 0xff;
+ if (ir->wait && !&dev->int_in)
return 0;
- }
if (&dev->int_in) {
- poll_result->rc_data[0] = ir->urb_data[0];
- poll_result->rc_data[1] = ir->urb_data[1];
+ if (ir->ir.ir_type == IR_TYPE_RC5)
+ poll_result->rc_data = ir->urb_data[0];
+ else
+ poll_result->rc_data = ir->urb_data[0] | ir->urb_data[1] << 8;
} else {
tm6000_set_reg(dev, REQ_04_EN_DISABLE_MCU_INT, 2, 0);
msleep(10);
tm6000_set_reg(dev, REQ_04_EN_DISABLE_MCU_INT, 2, 1);
msleep(10);
- rc = tm6000_read_write_usb(dev, USB_DIR_IN | USB_TYPE_VENDOR |
- USB_RECIP_DEVICE, REQ_02_GET_IR_CODE, 0, 0, buf, 1);
+ if (ir->ir.ir_type == IR_TYPE_RC5) {
+ rc = tm6000_read_write_usb(dev, USB_DIR_IN |
+ USB_TYPE_VENDOR | USB_RECIP_DEVICE,
+ REQ_02_GET_IR_CODE, 0, 0, buf, 1);
- msleep(10);
+ msleep(10);
- dprintk("read data=%02x\n", buf[0]);
- if (rc < 0)
- return rc;
+ dprintk("read data=%02x\n", buf[0]);
+ if (rc < 0)
+ return rc;
- poll_result->rc_data[0] = buf[0];
+ poll_result->rc_data = buf[0];
+ } else {
+ rc = tm6000_read_write_usb(dev, USB_DIR_IN |
+ USB_TYPE_VENDOR | USB_RECIP_DEVICE,
+ REQ_02_GET_IR_CODE, 0, 0, buf, 2);
+
+ msleep(10);
+
+ dprintk("read data=%04x\n", buf[0] | buf[1] << 8);
+ if (rc < 0)
+ return rc;
+
+ poll_result->rc_data = buf[0] | buf[1] << 8;
+ }
+ if ((poll_result->rc_data & 0x00ff) != 0xff)
+ ir->key = 1;
}
return 0;
}
@@ -180,12 +198,11 @@
return;
}
- dprintk("ir->get_key result data=%02x %02x\n",
- poll_result.rc_data[0], poll_result.rc_data[1]);
+ dprintk("ir->get_key result data=%04x\n", poll_result.rc_data);
- if (poll_result.rc_data[0] != 0xff && ir->key == 1) {
+ if (ir->key) {
ir_input_keydown(ir->input->input_dev, &ir->ir,
- poll_result.rc_data[0] | poll_result.rc_data[1] << 8);
+ (u32)poll_result.rc_data);
ir_input_nokey(ir->input->input_dev, &ir->ir);
ir->key = 0;
diff --git a/drivers/xen/xenbus/xenbus_probe.c b/drivers/xen/xenbus/xenbus_probe.c
index 29bac51..d409495 100644
--- a/drivers/xen/xenbus/xenbus_probe.c
+++ b/drivers/xen/xenbus/xenbus_probe.c
@@ -755,7 +755,10 @@
{
int ret = 0;
- blocking_notifier_chain_register(&xenstore_chain, nb);
+ if (xenstored_ready > 0)
+ ret = nb->notifier_call(nb, 0, NULL);
+ else
+ blocking_notifier_chain_register(&xenstore_chain, nb);
return ret;
}
@@ -769,7 +772,7 @@
void xenbus_probe(struct work_struct *unused)
{
- BUG_ON((xenstored_ready <= 0));
+ xenstored_ready = 1;
/* Enumerate devices in xenstore and watch for changes. */
xenbus_probe_devices(&xenbus_frontend);
@@ -835,8 +838,8 @@
xen_store_evtchn = xen_start_info->store_evtchn;
xen_store_mfn = xen_start_info->store_mfn;
xen_store_interface = mfn_to_virt(xen_store_mfn);
+ xenstored_ready = 1;
}
- xenstored_ready = 1;
}
/* Initialize the interface to xenstore. */
diff --git a/fs/binfmt_aout.c b/fs/binfmt_aout.c
index f96eff0..a6395bd 100644
--- a/fs/binfmt_aout.c
+++ b/fs/binfmt_aout.c
@@ -134,10 +134,6 @@
if (!dump_write(file, dump_start, dump_size))
goto end_coredump;
}
-/* Finally dump the task struct. Not be used by gdb, but could be useful */
- set_fs(KERNEL_DS);
- if (!dump_write(file, current, sizeof(*current)))
- goto end_coredump;
end_coredump:
set_fs(fs);
return has_dumped;
diff --git a/fs/ceph/caps.c b/fs/ceph/caps.c
index 73c1530..5e9da99 100644
--- a/fs/ceph/caps.c
+++ b/fs/ceph/caps.c
@@ -2283,7 +2283,8 @@
{
struct ceph_inode_info *ci = ceph_inode(inode);
int mds = session->s_mds;
- int seq = le32_to_cpu(grant->seq);
+ unsigned seq = le32_to_cpu(grant->seq);
+ unsigned issue_seq = le32_to_cpu(grant->issue_seq);
int newcaps = le32_to_cpu(grant->caps);
int issued, implemented, used, wanted, dirty;
u64 size = le64_to_cpu(grant->size);
@@ -2295,8 +2296,8 @@
int revoked_rdcache = 0;
int queue_invalidate = 0;
- dout("handle_cap_grant inode %p cap %p mds%d seq %d %s\n",
- inode, cap, mds, seq, ceph_cap_string(newcaps));
+ dout("handle_cap_grant inode %p cap %p mds%d seq %u/%u %s\n",
+ inode, cap, mds, seq, issue_seq, ceph_cap_string(newcaps));
dout(" size %llu max_size %llu, i_size %llu\n", size, max_size,
inode->i_size);
@@ -2392,6 +2393,7 @@
}
cap->seq = seq;
+ cap->issue_seq = issue_seq;
/* file layout may have changed */
ci->i_layout = grant->layout;
@@ -2774,15 +2776,7 @@
if (op == CEPH_CAP_OP_IMPORT)
__queue_cap_release(session, vino.ino, cap_id,
mseq, seq);
-
- /*
- * send any full release message to try to move things
- * along for the mds (who clearly thinks we still have this
- * cap).
- */
- ceph_add_cap_releases(mdsc, session);
- ceph_send_cap_releases(mdsc, session);
- goto done;
+ goto flush_cap_releases;
}
/* these will work even if we don't have a cap yet */
@@ -2810,7 +2804,7 @@
dout(" no cap on %p ino %llx.%llx from mds%d\n",
inode, ceph_ino(inode), ceph_snap(inode), mds);
spin_unlock(&inode->i_lock);
- goto done;
+ goto flush_cap_releases;
}
/* note that each of these drops i_lock for us */
@@ -2834,6 +2828,17 @@
ceph_cap_op_name(op));
}
+ goto done;
+
+flush_cap_releases:
+ /*
+ * send any full release message to try to move things
+ * along for the mds (who clearly thinks we still have this
+ * cap).
+ */
+ ceph_add_cap_releases(mdsc, session);
+ ceph_send_cap_releases(mdsc, session);
+
done:
mutex_unlock(&session->s_mutex);
done_unlocked:
diff --git a/fs/ceph/export.c b/fs/ceph/export.c
index 4480cb1..e38423e 100644
--- a/fs/ceph/export.c
+++ b/fs/ceph/export.c
@@ -42,32 +42,37 @@
static int ceph_encode_fh(struct dentry *dentry, u32 *rawfh, int *max_len,
int connectable)
{
+ int type;
struct ceph_nfs_fh *fh = (void *)rawfh;
struct ceph_nfs_confh *cfh = (void *)rawfh;
struct dentry *parent = dentry->d_parent;
struct inode *inode = dentry->d_inode;
- int type;
+ int connected_handle_length = sizeof(*cfh)/4;
+ int handle_length = sizeof(*fh)/4;
/* don't re-export snaps */
if (ceph_snap(inode) != CEPH_NOSNAP)
return -EINVAL;
- if (*max_len >= sizeof(*cfh)) {
+ if (*max_len >= connected_handle_length) {
dout("encode_fh %p connectable\n", dentry);
cfh->ino = ceph_ino(dentry->d_inode);
cfh->parent_ino = ceph_ino(parent->d_inode);
cfh->parent_name_hash = parent->d_name.hash;
- *max_len = sizeof(*cfh);
+ *max_len = connected_handle_length;
type = 2;
- } else if (*max_len > sizeof(*fh)) {
- if (connectable)
- return -ENOSPC;
+ } else if (*max_len >= handle_length) {
+ if (connectable) {
+ *max_len = connected_handle_length;
+ return 255;
+ }
dout("encode_fh %p\n", dentry);
fh->ino = ceph_ino(dentry->d_inode);
- *max_len = sizeof(*fh);
+ *max_len = handle_length;
type = 1;
} else {
- return -ENOSPC;
+ *max_len = handle_length;
+ return 255;
}
return type;
}
diff --git a/fs/ceph/file.c b/fs/ceph/file.c
index 8c044a4..66e4da6 100644
--- a/fs/ceph/file.c
+++ b/fs/ceph/file.c
@@ -697,7 +697,7 @@
* start_request so that a tid has been assigned.
*/
spin_lock(&ci->i_unsafe_lock);
- list_add(&ci->i_unsafe_writes, &req->r_unsafe_item);
+ list_add(&req->r_unsafe_item, &ci->i_unsafe_writes);
spin_unlock(&ci->i_unsafe_lock);
ceph_get_cap_refs(ci, CEPH_CAP_FILE_WR);
}
diff --git a/fs/ceph/osd_client.c b/fs/ceph/osd_client.c
index dfced1d..3b5571b 100644
--- a/fs/ceph/osd_client.c
+++ b/fs/ceph/osd_client.c
@@ -549,7 +549,7 @@
*/
static void __cancel_request(struct ceph_osd_request *req)
{
- if (req->r_sent) {
+ if (req->r_sent && req->r_osd) {
ceph_con_revoke(&req->r_osd->o_con, req->r_request);
req->r_sent = 0;
}
diff --git a/fs/exec.c b/fs/exec.c
index 828dd24..6d2b6f9 100644
--- a/fs/exec.c
+++ b/fs/exec.c
@@ -2014,3 +2014,43 @@
fail:
return;
}
+
+/*
+ * Core dumping helper functions. These are the only things you should
+ * do on a core-file: use only these functions to write out all the
+ * necessary info.
+ */
+int dump_write(struct file *file, const void *addr, int nr)
+{
+ return access_ok(VERIFY_READ, addr, nr) && file->f_op->write(file, addr, nr, &file->f_pos) == nr;
+}
+EXPORT_SYMBOL(dump_write);
+
+int dump_seek(struct file *file, loff_t off)
+{
+ int ret = 1;
+
+ if (file->f_op->llseek && file->f_op->llseek != no_llseek) {
+ if (file->f_op->llseek(file, off, SEEK_CUR) < 0)
+ return 0;
+ } else {
+ char *buf = (char *)get_zeroed_page(GFP_KERNEL);
+
+ if (!buf)
+ return 0;
+ while (off > 0) {
+ unsigned long n = off;
+
+ if (n > PAGE_SIZE)
+ n = PAGE_SIZE;
+ if (!dump_write(file, buf, n)) {
+ ret = 0;
+ break;
+ }
+ off -= n;
+ }
+ free_page((unsigned long)buf);
+ }
+ return ret;
+}
+EXPORT_SYMBOL(dump_seek);
diff --git a/fs/exofs/inode.c b/fs/exofs/inode.c
index eb7368e..3eadd97 100644
--- a/fs/exofs/inode.c
+++ b/fs/exofs/inode.c
@@ -54,6 +54,9 @@
unsigned nr_pages;
unsigned long length;
loff_t pg_first; /* keep 64bit also in 32-arches */
+ bool read_4_write; /* This means two things: that the read is sync
+ * And the pages should not be unlocked.
+ */
};
static void _pcol_init(struct page_collect *pcol, unsigned expected_pages,
@@ -71,6 +74,7 @@
pcol->nr_pages = 0;
pcol->length = 0;
pcol->pg_first = -1;
+ pcol->read_4_write = false;
}
static void _pcol_reset(struct page_collect *pcol)
@@ -347,7 +351,8 @@
if (PageError(page))
ClearPageError(page);
- unlock_page(page);
+ if (!pcol->read_4_write)
+ unlock_page(page);
EXOFS_DBGMSG("readpage_strip(0x%lx, 0x%lx) empty page,"
" splitting\n", inode->i_ino, page->index);
@@ -428,6 +433,7 @@
/* readpage_strip might call read_exec(,is_sync==false) at several
* places but not if we have a single page.
*/
+ pcol.read_4_write = is_sync;
ret = readpage_strip(&pcol, page);
if (ret) {
EXOFS_ERR("_readpage => %d\n", ret);
diff --git a/fs/fs-writeback.c b/fs/fs-writeback.c
index 5581122..ab38fef 100644
--- a/fs/fs-writeback.c
+++ b/fs/fs-writeback.c
@@ -72,22 +72,11 @@
static inline struct backing_dev_info *inode_to_bdi(struct inode *inode)
{
struct super_block *sb = inode->i_sb;
- struct backing_dev_info *bdi = inode->i_mapping->backing_dev_info;
- /*
- * For inodes on standard filesystems, we use superblock's bdi. For
- * inodes on virtual filesystems, we want to use inode mapping's bdi
- * because they can possibly point to something useful (think about
- * block_dev filesystem).
- */
- if (sb->s_bdi && sb->s_bdi != &noop_backing_dev_info) {
- /* Some device inodes could play dirty tricks. Catch them... */
- WARN(bdi != sb->s_bdi && bdi_cap_writeback_dirty(bdi),
- "Dirtiable inode bdi %s != sb bdi %s\n",
- bdi->name, sb->s_bdi->name);
- return sb->s_bdi;
- }
- return bdi;
+ if (strcmp(sb->s_type->name, "bdev") == 0)
+ return inode->i_mapping->backing_dev_info;
+
+ return sb->s_bdi;
}
static void bdi_queue_work(struct backing_dev_info *bdi,
diff --git a/fs/fuse/dev.c b/fs/fuse/dev.c
index d367af1..cde755c 100644
--- a/fs/fuse/dev.c
+++ b/fs/fuse/dev.c
@@ -1354,7 +1354,7 @@
loff_t file_size;
unsigned int num;
unsigned int offset;
- size_t total_len;
+ size_t total_len = 0;
req = fuse_get_req(fc);
if (IS_ERR(req))
diff --git a/fs/nfsd/nfsfh.h b/fs/nfsd/nfsfh.h
index cdfb8c6..c16f8d8 100644
--- a/fs/nfsd/nfsfh.h
+++ b/fs/nfsd/nfsfh.h
@@ -196,8 +196,6 @@
static inline void
fh_unlock(struct svc_fh *fhp)
{
- BUG_ON(!fhp->fh_dentry);
-
if (fhp->fh_locked) {
fill_post_wcc(fhp);
mutex_unlock(&fhp->fh_dentry->d_inode->i_mutex);
diff --git a/fs/notify/Kconfig b/fs/notify/Kconfig
index 22c629e..b388443 100644
--- a/fs/notify/Kconfig
+++ b/fs/notify/Kconfig
@@ -3,4 +3,4 @@
source "fs/notify/dnotify/Kconfig"
source "fs/notify/inotify/Kconfig"
-source "fs/notify/fanotify/Kconfig"
+#source "fs/notify/fanotify/Kconfig"
diff --git a/fs/xfs/linux-2.6/xfs_sync.c b/fs/xfs/linux-2.6/xfs_sync.c
index d59c4a6..81976ff 100644
--- a/fs/xfs/linux-2.6/xfs_sync.c
+++ b/fs/xfs/linux-2.6/xfs_sync.c
@@ -668,14 +668,11 @@
xfs_perag_put(pag);
}
-void
-__xfs_inode_clear_reclaim_tag(
- xfs_mount_t *mp,
+STATIC void
+__xfs_inode_clear_reclaim(
xfs_perag_t *pag,
xfs_inode_t *ip)
{
- radix_tree_tag_clear(&pag->pag_ici_root,
- XFS_INO_TO_AGINO(mp, ip->i_ino), XFS_ICI_RECLAIM_TAG);
pag->pag_ici_reclaimable--;
if (!pag->pag_ici_reclaimable) {
/* clear the reclaim tag from the perag radix tree */
@@ -689,6 +686,17 @@
}
}
+void
+__xfs_inode_clear_reclaim_tag(
+ xfs_mount_t *mp,
+ xfs_perag_t *pag,
+ xfs_inode_t *ip)
+{
+ radix_tree_tag_clear(&pag->pag_ici_root,
+ XFS_INO_TO_AGINO(mp, ip->i_ino), XFS_ICI_RECLAIM_TAG);
+ __xfs_inode_clear_reclaim(pag, ip);
+}
+
/*
* Inodes in different states need to be treated differently, and the return
* value of xfs_iflush is not sufficient to get this right. The following table
@@ -838,6 +846,7 @@
if (!radix_tree_delete(&pag->pag_ici_root,
XFS_INO_TO_AGINO(ip->i_mount, ip->i_ino)))
ASSERT(0);
+ __xfs_inode_clear_reclaim(pag, ip);
write_unlock(&pag->pag_ici_lock);
/*
diff --git a/include/drm/ttm/ttm_bo_api.h b/include/drm/ttm/ttm_bo_api.h
index 267a86c..2040e6c 100644
--- a/include/drm/ttm/ttm_bo_api.h
+++ b/include/drm/ttm/ttm_bo_api.h
@@ -246,9 +246,11 @@
atomic_t reserved;
-
/**
* Members protected by the bo::lock
+ * In addition, setting sync_obj to anything else
+ * than NULL requires bo::reserved to be held. This allows for
+ * checking NULL while reserved but not holding bo::lock.
*/
void *sync_obj_arg;
diff --git a/include/linux/Kbuild b/include/linux/Kbuild
index 626b629..4e8ea8c 100644
--- a/include/linux/Kbuild
+++ b/include/linux/Kbuild
@@ -118,7 +118,6 @@
header-y += ext2_fs.h
header-y += fadvise.h
header-y += falloc.h
-header-y += fanotify.h
header-y += fb.h
header-y += fcntl.h
header-y += fd.h
diff --git a/include/linux/coredump.h b/include/linux/coredump.h
index 8ba66a9..ba4b85a 100644
--- a/include/linux/coredump.h
+++ b/include/linux/coredump.h
@@ -9,37 +9,7 @@
* These are the only things you should do on a core-file: use only these
* functions to write out all the necessary info.
*/
-static inline int dump_write(struct file *file, const void *addr, int nr)
-{
- return file->f_op->write(file, addr, nr, &file->f_pos) == nr;
-}
-
-static inline int dump_seek(struct file *file, loff_t off)
-{
- int ret = 1;
-
- if (file->f_op->llseek && file->f_op->llseek != no_llseek) {
- if (file->f_op->llseek(file, off, SEEK_CUR) < 0)
- return 0;
- } else {
- char *buf = (char *)get_zeroed_page(GFP_KERNEL);
-
- if (!buf)
- return 0;
- while (off > 0) {
- unsigned long n = off;
-
- if (n > PAGE_SIZE)
- n = PAGE_SIZE;
- if (!dump_write(file, buf, n)) {
- ret = 0;
- break;
- }
- off -= n;
- }
- free_page((unsigned long)buf);
- }
- return ret;
-}
+extern int dump_write(struct file *file, const void *addr, int nr);
+extern int dump_seek(struct file *file, loff_t off);
#endif /* _LINUX_COREDUMP_H */
diff --git a/include/linux/elevator.h b/include/linux/elevator.h
index 926b503..4fd978e 100644
--- a/include/linux/elevator.h
+++ b/include/linux/elevator.h
@@ -93,6 +93,7 @@
struct elevator_type *elevator_type;
struct mutex sysfs_lock;
struct hlist_head *hash;
+ unsigned int registered:1;
};
/*
diff --git a/include/linux/module.h b/include/linux/module.h
index 8a6b9fd..aace066 100644
--- a/include/linux/module.h
+++ b/include/linux/module.h
@@ -686,17 +686,16 @@
#ifdef CONFIG_GENERIC_BUG
-int module_bug_finalize(const Elf_Ehdr *, const Elf_Shdr *,
+void module_bug_finalize(const Elf_Ehdr *, const Elf_Shdr *,
struct module *);
void module_bug_cleanup(struct module *);
#else /* !CONFIG_GENERIC_BUG */
-static inline int module_bug_finalize(const Elf_Ehdr *hdr,
+static inline void module_bug_finalize(const Elf_Ehdr *hdr,
const Elf_Shdr *sechdrs,
struct module *mod)
{
- return 0;
}
static inline void module_bug_cleanup(struct module *mod) {}
#endif /* CONFIG_GENERIC_BUG */
diff --git a/include/linux/rcupdate.h b/include/linux/rcupdate.h
index 9fbc54a..83af1f8 100644
--- a/include/linux/rcupdate.h
+++ b/include/linux/rcupdate.h
@@ -454,7 +454,7 @@
* Makes rcu_dereference_check() do the dirty work.
*/
#define rcu_dereference_bh(p) \
- rcu_dereference_check(p, rcu_read_lock_bh_held())
+ rcu_dereference_check(p, rcu_read_lock_bh_held() || irqs_disabled())
/**
* rcu_dereference_sched - fetch RCU-protected pointer, checking for RCU-sched
diff --git a/include/linux/types.h b/include/linux/types.h
index 01a082f..357dbc1 100644
--- a/include/linux/types.h
+++ b/include/linux/types.h
@@ -121,7 +121,15 @@
typedef __s64 int64_t;
#endif
-/* this is a special 64bit data type that is 8-byte aligned */
+/*
+ * aligned_u64 should be used in defining kernel<->userspace ABIs to avoid
+ * common 32/64-bit compat problems.
+ * 64-bit values align to 4-byte boundaries on x86_32 (and possibly other
+ * architectures) and to 8-byte boundaries on 64-bit architetures. The new
+ * aligned_64 type enforces 8-byte alignment so that structs containing
+ * aligned_64 values have the same alignment on 32-bit and 64-bit architectures.
+ * No conversions are necessary between 32-bit user-space and a 64-bit kernel.
+ */
#define aligned_u64 __u64 __attribute__((aligned(8)))
#define aligned_be64 __be64 __attribute__((aligned(8)))
#define aligned_le64 __le64 __attribute__((aligned(8)))
@@ -178,6 +186,11 @@
typedef __u16 __bitwise __sum16;
typedef __u32 __bitwise __wsum;
+/* this is a special 64bit data type that is 8-byte aligned */
+#define __aligned_u64 __u64 __attribute__((aligned(8)))
+#define __aligned_be64 __be64 __attribute__((aligned(8)))
+#define __aligned_le64 __le64 __attribute__((aligned(8)))
+
#ifdef __KERNEL__
typedef unsigned __bitwise__ gfp_t;
typedef unsigned __bitwise__ fmode_t;
diff --git a/include/linux/wait.h b/include/linux/wait.h
index 0836ccc..3efc9f3 100644
--- a/include/linux/wait.h
+++ b/include/linux/wait.h
@@ -614,6 +614,7 @@
(wait)->private = current; \
(wait)->func = autoremove_wake_function; \
INIT_LIST_HEAD(&(wait)->task_list); \
+ (wait)->flags = 0; \
} while (0)
/**
diff --git a/include/media/videobuf-dma-sg.h b/include/media/videobuf-dma-sg.h
index 97e07f46a..aa4ebb4 100644
--- a/include/media/videobuf-dma-sg.h
+++ b/include/media/videobuf-dma-sg.h
@@ -48,6 +48,7 @@
/* for userland buffer */
int offset;
+ size_t size;
struct page **pages;
/* for kernel buffers */
diff --git a/include/net/bluetooth/bluetooth.h b/include/net/bluetooth/bluetooth.h
index 27a902d..30fce01 100644
--- a/include/net/bluetooth/bluetooth.h
+++ b/include/net/bluetooth/bluetooth.h
@@ -161,12 +161,30 @@
{
struct sk_buff *skb;
+ release_sock(sk);
if ((skb = sock_alloc_send_skb(sk, len + BT_SKB_RESERVE, nb, err))) {
skb_reserve(skb, BT_SKB_RESERVE);
bt_cb(skb)->incoming = 0;
}
+ lock_sock(sk);
+
+ if (!skb && *err)
+ return NULL;
+
+ *err = sock_error(sk);
+ if (*err)
+ goto out;
+
+ if (sk->sk_shutdown) {
+ *err = -ECONNRESET;
+ goto out;
+ }
return skb;
+
+out:
+ kfree_skb(skb);
+ return NULL;
}
int bt_err(__u16 code);
diff --git a/kernel/hrtimer.c b/kernel/hrtimer.c
index 1decafb..72206cf 100644
--- a/kernel/hrtimer.c
+++ b/kernel/hrtimer.c
@@ -931,6 +931,7 @@
remove_hrtimer(struct hrtimer *timer, struct hrtimer_clock_base *base)
{
if (hrtimer_is_queued(timer)) {
+ unsigned long state;
int reprogram;
/*
@@ -944,8 +945,13 @@
debug_deactivate(timer);
timer_stats_hrtimer_clear_start_info(timer);
reprogram = base->cpu_base == &__get_cpu_var(hrtimer_bases);
- __remove_hrtimer(timer, base, HRTIMER_STATE_INACTIVE,
- reprogram);
+ /*
+ * We must preserve the CALLBACK state flag here,
+ * otherwise we could move the timer base in
+ * switch_hrtimer_base.
+ */
+ state = timer->state & HRTIMER_STATE_CALLBACK;
+ __remove_hrtimer(timer, base, state, reprogram);
return 1;
}
return 0;
@@ -1231,6 +1237,9 @@
BUG_ON(timer->state != HRTIMER_STATE_CALLBACK);
enqueue_hrtimer(timer, base);
}
+
+ WARN_ON_ONCE(!(timer->state & HRTIMER_STATE_CALLBACK));
+
timer->state &= ~HRTIMER_STATE_CALLBACK;
}
diff --git a/kernel/module.c b/kernel/module.c
index d0b5f8d..ccd6419 100644
--- a/kernel/module.c
+++ b/kernel/module.c
@@ -1537,6 +1537,7 @@
{
struct module *mod = _mod;
list_del(&mod->list);
+ module_bug_cleanup(mod);
return 0;
}
@@ -2625,6 +2626,7 @@
if (err < 0)
goto ddebug;
+ module_bug_finalize(info.hdr, info.sechdrs, mod);
list_add_rcu(&mod->list, &modules);
mutex_unlock(&module_mutex);
@@ -2650,6 +2652,8 @@
mutex_lock(&module_mutex);
/* Unlink carefully: kallsyms could be walking list. */
list_del_rcu(&mod->list);
+ module_bug_cleanup(mod);
+
ddebug:
if (!mod->taints)
dynamic_debug_remove(info.debug);
diff --git a/kernel/perf_event.c b/kernel/perf_event.c
index db5b560..b98bed3 100644
--- a/kernel/perf_event.c
+++ b/kernel/perf_event.c
@@ -2202,15 +2202,13 @@
static int perf_event_period(struct perf_event *event, u64 __user *arg)
{
struct perf_event_context *ctx = event->ctx;
- unsigned long size;
int ret = 0;
u64 value;
if (!event->attr.sample_period)
return -EINVAL;
- size = copy_from_user(&value, arg, sizeof(value));
- if (size != sizeof(value))
+ if (copy_from_user(&value, arg, sizeof(value)))
return -EFAULT;
if (!value)
diff --git a/kernel/signal.c b/kernel/signal.c
index bded651..919562c 100644
--- a/kernel/signal.c
+++ b/kernel/signal.c
@@ -2215,6 +2215,14 @@
#ifdef __ARCH_SI_TRAPNO
err |= __put_user(from->si_trapno, &to->si_trapno);
#endif
+#ifdef BUS_MCEERR_AO
+ /*
+ * Other callers might not initialize the si_lsb field,
+ * so check explicitely for the right codes here.
+ */
+ if (from->si_code == BUS_MCEERR_AR || from->si_code == BUS_MCEERR_AO)
+ err |= __put_user(from->si_addr_lsb, &to->si_addr_lsb);
+#endif
break;
case __SI_CHLD:
err |= __put_user(from->si_pid, &to->si_pid);
diff --git a/kernel/smp.c b/kernel/smp.c
index 75c970c..ed6aacf 100644
--- a/kernel/smp.c
+++ b/kernel/smp.c
@@ -365,9 +365,10 @@
EXPORT_SYMBOL_GPL(smp_call_function_any);
/**
- * __smp_call_function_single(): Run a function on another CPU
+ * __smp_call_function_single(): Run a function on a specific CPU
* @cpu: The CPU to run on.
* @data: Pre-allocated and setup data structure
+ * @wait: If true, wait until function has completed on specified CPU.
*
* Like smp_call_function_single(), but allow caller to pass in a
* pre-allocated data structure. Useful for embedding @data inside
@@ -376,8 +377,10 @@
void __smp_call_function_single(int cpu, struct call_single_data *data,
int wait)
{
- csd_lock(data);
+ unsigned int this_cpu;
+ unsigned long flags;
+ this_cpu = get_cpu();
/*
* Can deadlock when called with interrupts disabled.
* We allow cpu's that are not yet online though, as no one else can
@@ -387,7 +390,15 @@
WARN_ON_ONCE(cpu_online(smp_processor_id()) && wait && irqs_disabled()
&& !oops_in_progress);
- generic_exec_single(cpu, data, wait);
+ if (cpu == this_cpu) {
+ local_irq_save(flags);
+ data->func(data->info);
+ local_irq_restore(flags);
+ } else {
+ csd_lock(data);
+ generic_exec_single(cpu, data, wait);
+ }
+ put_cpu();
}
/**
diff --git a/kernel/sysctl.c b/kernel/sysctl.c
index f88552c..3a45c22 100644
--- a/kernel/sysctl.c
+++ b/kernel/sysctl.c
@@ -2485,7 +2485,7 @@
kbuf[left] = 0;
}
- for (; left && vleft--; i++, min++, max++, first=0) {
+ for (; left && vleft--; i++, first = 0) {
unsigned long val;
if (write) {
diff --git a/kernel/sysctl_check.c b/kernel/sysctl_check.c
index 04cdcf7..10b90d8 100644
--- a/kernel/sysctl_check.c
+++ b/kernel/sysctl_check.c
@@ -143,15 +143,6 @@
if (!table->maxlen)
set_fail(&fail, table, "No maxlen");
}
- if ((table->proc_handler == proc_doulongvec_minmax) ||
- (table->proc_handler == proc_doulongvec_ms_jiffies_minmax)) {
- if (table->maxlen > sizeof (unsigned long)) {
- if (!table->extra1)
- set_fail(&fail, table, "No min");
- if (!table->extra2)
- set_fail(&fail, table, "No max");
- }
- }
#ifdef CONFIG_PROC_SYSCTL
if (table->procname && !table->proc_handler)
set_fail(&fail, table, "No proc_handler");
diff --git a/kernel/trace/ring_buffer.c b/kernel/trace/ring_buffer.c
index 492197e..bca9637 100644
--- a/kernel/trace/ring_buffer.c
+++ b/kernel/trace/ring_buffer.c
@@ -405,7 +405,7 @@
#define BUF_MAX_DATA_SIZE (BUF_PAGE_SIZE - (sizeof(u32) * 2))
/* Max number of timestamps that can fit on a page */
-#define RB_TIMESTAMPS_PER_PAGE (BUF_PAGE_SIZE / RB_LEN_TIME_STAMP)
+#define RB_TIMESTAMPS_PER_PAGE (BUF_PAGE_SIZE / RB_LEN_TIME_EXTEND)
int ring_buffer_print_page_header(struct trace_seq *s)
{
diff --git a/lib/bug.c b/lib/bug.c
index 7cdfad8..1955209 100644
--- a/lib/bug.c
+++ b/lib/bug.c
@@ -72,8 +72,8 @@
return NULL;
}
-int module_bug_finalize(const Elf_Ehdr *hdr, const Elf_Shdr *sechdrs,
- struct module *mod)
+void module_bug_finalize(const Elf_Ehdr *hdr, const Elf_Shdr *sechdrs,
+ struct module *mod)
{
char *secstrings;
unsigned int i;
@@ -97,8 +97,6 @@
* could potentially lead to deadlock and thus be counter-productive.
*/
list_add(&mod->bug_list, &module_bug_list);
-
- return 0;
}
void module_bug_cleanup(struct module *mod)
diff --git a/mm/ksm.c b/mm/ksm.c
index b1873cf..65ab5c7 100644
--- a/mm/ksm.c
+++ b/mm/ksm.c
@@ -712,7 +712,7 @@
if (!ptep)
goto out;
- if (pte_write(*ptep)) {
+ if (pte_write(*ptep) || pte_dirty(*ptep)) {
pte_t entry;
swapped = PageSwapCache(page);
@@ -735,7 +735,9 @@
set_pte_at(mm, addr, ptep, entry);
goto out_unlock;
}
- entry = pte_wrprotect(entry);
+ if (pte_dirty(entry))
+ set_page_dirty(page);
+ entry = pte_mkclean(pte_wrprotect(entry));
set_pte_at_notify(mm, addr, ptep, entry);
}
*orig_pte = *ptep;
diff --git a/mm/memcontrol.c b/mm/memcontrol.c
index 3eed583..9be3cf8 100644
--- a/mm/memcontrol.c
+++ b/mm/memcontrol.c
@@ -3587,9 +3587,13 @@
static void mem_cgroup_threshold(struct mem_cgroup *memcg)
{
- __mem_cgroup_threshold(memcg, false);
- if (do_swap_account)
- __mem_cgroup_threshold(memcg, true);
+ while (memcg) {
+ __mem_cgroup_threshold(memcg, false);
+ if (do_swap_account)
+ __mem_cgroup_threshold(memcg, true);
+
+ memcg = parent_mem_cgroup(memcg);
+ }
}
static int compare_thresholds(const void *a, const void *b)
diff --git a/mm/memory-failure.c b/mm/memory-failure.c
index 9c26eec..757f6b0 100644
--- a/mm/memory-failure.c
+++ b/mm/memory-failure.c
@@ -183,7 +183,7 @@
* signal.
*/
static int kill_proc_ao(struct task_struct *t, unsigned long addr, int trapno,
- unsigned long pfn)
+ unsigned long pfn, struct page *page)
{
struct siginfo si;
int ret;
@@ -198,7 +198,7 @@
#ifdef __ARCH_SI_TRAPNO
si.si_trapno = trapno;
#endif
- si.si_addr_lsb = PAGE_SHIFT;
+ si.si_addr_lsb = compound_order(compound_head(page)) + PAGE_SHIFT;
/*
* Don't use force here, it's convenient if the signal
* can be temporarily blocked.
@@ -235,7 +235,7 @@
int nr;
do {
nr = shrink_slab(1000, GFP_KERNEL, 1000);
- if (page_count(p) == 0)
+ if (page_count(p) == 1)
break;
} while (nr > 10);
}
@@ -327,7 +327,7 @@
* wrong earlier.
*/
static void kill_procs_ao(struct list_head *to_kill, int doit, int trapno,
- int fail, unsigned long pfn)
+ int fail, struct page *page, unsigned long pfn)
{
struct to_kill *tk, *next;
@@ -352,7 +352,7 @@
* process anyways.
*/
else if (kill_proc_ao(tk->tsk, tk->addr, trapno,
- pfn) < 0)
+ pfn, page) < 0)
printk(KERN_ERR
"MCE %#lx: Cannot send advisory machine check signal to %s:%d\n",
pfn, tk->tsk->comm, tk->tsk->pid);
@@ -928,7 +928,7 @@
* any accesses to the poisoned memory.
*/
kill_procs_ao(&tokill, !!PageDirty(hpage), trapno,
- ret != SWAP_SUCCESS, pfn);
+ ret != SWAP_SUCCESS, p, pfn);
return ret;
}
diff --git a/mm/page_alloc.c b/mm/page_alloc.c
index a8cfa9c..f12ad18 100644
--- a/mm/page_alloc.c
+++ b/mm/page_alloc.c
@@ -5182,9 +5182,9 @@
if (!table)
panic("Failed to allocate %s hash table\n", tablename);
- printk(KERN_INFO "%s hash table entries: %d (order: %d, %lu bytes)\n",
+ printk(KERN_INFO "%s hash table entries: %ld (order: %d, %lu bytes)\n",
tablename,
- (1U << log2qty),
+ (1UL << log2qty),
ilog2(size) - PAGE_SHIFT,
size);
diff --git a/mm/rmap.c b/mm/rmap.c
index 9d2ba01..92e6757 100644
--- a/mm/rmap.c
+++ b/mm/rmap.c
@@ -381,7 +381,13 @@
unsigned long page_address_in_vma(struct page *page, struct vm_area_struct *vma)
{
if (PageAnon(page)) {
- if (vma->anon_vma->root != page_anon_vma(page)->root)
+ struct anon_vma *page__anon_vma = page_anon_vma(page);
+ /*
+ * Note: swapoff's unuse_vma() is more efficient with this
+ * check, and needs it to match anon_vma when KSM is active.
+ */
+ if (!vma->anon_vma || !page__anon_vma ||
+ vma->anon_vma->root != page__anon_vma->root)
return -EFAULT;
} else if (page->mapping && !(vma->vm_flags & VM_NONLINEAR)) {
if (!vma->vm_file ||
diff --git a/net/8021q/vlan_core.c b/net/8021q/vlan_core.c
index 01ddb04..0eb96f7 100644
--- a/net/8021q/vlan_core.c
+++ b/net/8021q/vlan_core.c
@@ -24,8 +24,11 @@
if (vlan_dev)
skb->dev = vlan_dev;
- else if (vlan_id)
- goto drop;
+ else if (vlan_id) {
+ if (!(skb->dev->flags & IFF_PROMISC))
+ goto drop;
+ skb->pkt_type = PACKET_OTHERHOST;
+ }
return (polling ? netif_receive_skb(skb) : netif_rx(skb));
@@ -102,8 +105,11 @@
if (vlan_dev)
skb->dev = vlan_dev;
- else if (vlan_id)
- goto drop;
+ else if (vlan_id) {
+ if (!(skb->dev->flags & IFF_PROMISC))
+ goto drop;
+ skb->pkt_type = PACKET_OTHERHOST;
+ }
for (p = napi->gro_list; p; p = p->next) {
NAPI_GRO_CB(p)->same_flow =
diff --git a/net/atm/mpc.c b/net/atm/mpc.c
index 622b471..74bcc66 100644
--- a/net/atm/mpc.c
+++ b/net/atm/mpc.c
@@ -778,7 +778,7 @@
eg->packets_rcvd++;
mpc->eg_ops->put(eg);
- memset(ATM_SKB(skb), 0, sizeof(struct atm_skb_data));
+ memset(ATM_SKB(new_skb), 0, sizeof(struct atm_skb_data));
netif_rx(new_skb);
}
diff --git a/net/bluetooth/l2cap.c b/net/bluetooth/l2cap.c
index fadf26b..0b54b7d 100644
--- a/net/bluetooth/l2cap.c
+++ b/net/bluetooth/l2cap.c
@@ -1441,33 +1441,23 @@
static void l2cap_streaming_send(struct sock *sk)
{
- struct sk_buff *skb, *tx_skb;
+ struct sk_buff *skb;
struct l2cap_pinfo *pi = l2cap_pi(sk);
u16 control, fcs;
- while ((skb = sk->sk_send_head)) {
- tx_skb = skb_clone(skb, GFP_ATOMIC);
-
- control = get_unaligned_le16(tx_skb->data + L2CAP_HDR_SIZE);
+ while ((skb = skb_dequeue(TX_QUEUE(sk)))) {
+ control = get_unaligned_le16(skb->data + L2CAP_HDR_SIZE);
control |= pi->next_tx_seq << L2CAP_CTRL_TXSEQ_SHIFT;
- put_unaligned_le16(control, tx_skb->data + L2CAP_HDR_SIZE);
+ put_unaligned_le16(control, skb->data + L2CAP_HDR_SIZE);
if (pi->fcs == L2CAP_FCS_CRC16) {
- fcs = crc16(0, (u8 *)tx_skb->data, tx_skb->len - 2);
- put_unaligned_le16(fcs, tx_skb->data + tx_skb->len - 2);
+ fcs = crc16(0, (u8 *)skb->data, skb->len - 2);
+ put_unaligned_le16(fcs, skb->data + skb->len - 2);
}
- l2cap_do_send(sk, tx_skb);
+ l2cap_do_send(sk, skb);
pi->next_tx_seq = (pi->next_tx_seq + 1) % 64;
-
- if (skb_queue_is_last(TX_QUEUE(sk), skb))
- sk->sk_send_head = NULL;
- else
- sk->sk_send_head = skb_queue_next(TX_QUEUE(sk), skb);
-
- skb = skb_dequeue(TX_QUEUE(sk));
- kfree_skb(skb);
}
}
@@ -1960,6 +1950,11 @@
switch (optname) {
case L2CAP_OPTIONS:
+ if (sk->sk_state == BT_CONNECTED) {
+ err = -EINVAL;
+ break;
+ }
+
opts.imtu = l2cap_pi(sk)->imtu;
opts.omtu = l2cap_pi(sk)->omtu;
opts.flush_to = l2cap_pi(sk)->flush_to;
@@ -2771,10 +2766,10 @@
case L2CAP_CONF_MTU:
if (val < L2CAP_DEFAULT_MIN_MTU) {
*result = L2CAP_CONF_UNACCEPT;
- pi->omtu = L2CAP_DEFAULT_MIN_MTU;
+ pi->imtu = L2CAP_DEFAULT_MIN_MTU;
} else
- pi->omtu = val;
- l2cap_add_conf_opt(&ptr, L2CAP_CONF_MTU, 2, pi->omtu);
+ pi->imtu = val;
+ l2cap_add_conf_opt(&ptr, L2CAP_CONF_MTU, 2, pi->imtu);
break;
case L2CAP_CONF_FLUSH_TO:
@@ -3071,6 +3066,17 @@
return 0;
}
+static inline void set_default_fcs(struct l2cap_pinfo *pi)
+{
+ /* FCS is enabled only in ERTM or streaming mode, if one or both
+ * sides request it.
+ */
+ if (pi->mode != L2CAP_MODE_ERTM && pi->mode != L2CAP_MODE_STREAMING)
+ pi->fcs = L2CAP_FCS_NONE;
+ else if (!(pi->conf_state & L2CAP_CONF_NO_FCS_RECV))
+ pi->fcs = L2CAP_FCS_CRC16;
+}
+
static inline int l2cap_config_req(struct l2cap_conn *conn, struct l2cap_cmd_hdr *cmd, u16 cmd_len, u8 *data)
{
struct l2cap_conf_req *req = (struct l2cap_conf_req *) data;
@@ -3088,14 +3094,8 @@
if (!sk)
return -ENOENT;
- if (sk->sk_state != BT_CONFIG) {
- struct l2cap_cmd_rej rej;
-
- rej.reason = cpu_to_le16(0x0002);
- l2cap_send_cmd(conn, cmd->ident, L2CAP_COMMAND_REJ,
- sizeof(rej), &rej);
+ if (sk->sk_state == BT_DISCONN)
goto unlock;
- }
/* Reject if config buffer is too small. */
len = cmd_len - sizeof(*req);
@@ -3135,9 +3135,7 @@
goto unlock;
if (l2cap_pi(sk)->conf_state & L2CAP_CONF_INPUT_DONE) {
- if (!(l2cap_pi(sk)->conf_state & L2CAP_CONF_NO_FCS_RECV) ||
- l2cap_pi(sk)->fcs != L2CAP_FCS_NONE)
- l2cap_pi(sk)->fcs = L2CAP_FCS_CRC16;
+ set_default_fcs(l2cap_pi(sk));
sk->sk_state = BT_CONNECTED;
@@ -3225,9 +3223,7 @@
l2cap_pi(sk)->conf_state |= L2CAP_CONF_INPUT_DONE;
if (l2cap_pi(sk)->conf_state & L2CAP_CONF_OUTPUT_DONE) {
- if (!(l2cap_pi(sk)->conf_state & L2CAP_CONF_NO_FCS_RECV) ||
- l2cap_pi(sk)->fcs != L2CAP_FCS_NONE)
- l2cap_pi(sk)->fcs = L2CAP_FCS_CRC16;
+ set_default_fcs(l2cap_pi(sk));
sk->sk_state = BT_CONNECTED;
l2cap_pi(sk)->next_tx_seq = 0;
diff --git a/net/bluetooth/rfcomm/sock.c b/net/bluetooth/rfcomm/sock.c
index 44a6232..194b3a0 100644
--- a/net/bluetooth/rfcomm/sock.c
+++ b/net/bluetooth/rfcomm/sock.c
@@ -82,11 +82,14 @@
static void rfcomm_sk_state_change(struct rfcomm_dlc *d, int err)
{
struct sock *sk = d->owner, *parent;
+ unsigned long flags;
+
if (!sk)
return;
BT_DBG("dlc %p state %ld err %d", d, d->state, err);
+ local_irq_save(flags);
bh_lock_sock(sk);
if (err)
@@ -108,6 +111,7 @@
}
bh_unlock_sock(sk);
+ local_irq_restore(flags);
if (parent && sock_flag(sk, SOCK_ZAPPED)) {
/* We have to drop DLC lock here, otherwise
diff --git a/net/caif/caif_socket.c b/net/caif/caif_socket.c
index 8ce9047..4bf28f2 100644
--- a/net/caif/caif_socket.c
+++ b/net/caif/caif_socket.c
@@ -827,6 +827,7 @@
long timeo;
int err;
int ifindex, headroom, tailroom;
+ unsigned int mtu;
struct net_device *dev;
lock_sock(sk);
@@ -896,15 +897,23 @@
cf_sk->sk.sk_state = CAIF_DISCONNECTED;
goto out;
}
- dev = dev_get_by_index(sock_net(sk), ifindex);
+
+ err = -ENODEV;
+ rcu_read_lock();
+ dev = dev_get_by_index_rcu(sock_net(sk), ifindex);
+ if (!dev) {
+ rcu_read_unlock();
+ goto out;
+ }
cf_sk->headroom = LL_RESERVED_SPACE_EXTRA(dev, headroom);
+ mtu = dev->mtu;
+ rcu_read_unlock();
+
cf_sk->tailroom = tailroom;
- cf_sk->maxframe = dev->mtu - (headroom + tailroom);
- dev_put(dev);
+ cf_sk->maxframe = mtu - (headroom + tailroom);
if (cf_sk->maxframe < 1) {
- pr_warning("CAIF: %s(): CAIF Interface MTU too small (%d)\n",
- __func__, dev->mtu);
- err = -ENODEV;
+ pr_warning("CAIF: %s(): CAIF Interface MTU too small (%u)\n",
+ __func__, mtu);
goto out;
}
diff --git a/net/core/ethtool.c b/net/core/ethtool.c
index 7a85367..8451ab4 100644
--- a/net/core/ethtool.c
+++ b/net/core/ethtool.c
@@ -348,7 +348,7 @@
if (info.cmd == ETHTOOL_GRXCLSRLALL) {
if (info.rule_cnt > 0) {
if (info.rule_cnt <= KMALLOC_MAX_SIZE / sizeof(u32))
- rule_buf = kmalloc(info.rule_cnt * sizeof(u32),
+ rule_buf = kzalloc(info.rule_cnt * sizeof(u32),
GFP_USER);
if (!rule_buf)
return -ENOMEM;
@@ -397,7 +397,7 @@
(KMALLOC_MAX_SIZE - sizeof(*indir)) / sizeof(*indir->ring_index))
return -ENOMEM;
full_size = sizeof(*indir) + sizeof(*indir->ring_index) * table_size;
- indir = kmalloc(full_size, GFP_USER);
+ indir = kzalloc(full_size, GFP_USER);
if (!indir)
return -ENOMEM;
@@ -538,7 +538,7 @@
gstrings.len = ret;
- data = kmalloc(gstrings.len * ETH_GSTRING_LEN, GFP_USER);
+ data = kzalloc(gstrings.len * ETH_GSTRING_LEN, GFP_USER);
if (!data)
return -ENOMEM;
@@ -775,7 +775,7 @@
if (regs.len > reglen)
regs.len = reglen;
- regbuf = kmalloc(reglen, GFP_USER);
+ regbuf = kzalloc(reglen, GFP_USER);
if (!regbuf)
return -ENOMEM;
diff --git a/net/core/stream.c b/net/core/stream.c
index d959e0f..f5df85d 100644
--- a/net/core/stream.c
+++ b/net/core/stream.c
@@ -141,10 +141,10 @@
set_bit(SOCK_NOSPACE, &sk->sk_socket->flags);
sk->sk_write_pending++;
- sk_wait_event(sk, ¤t_timeo, !sk->sk_err &&
- !(sk->sk_shutdown & SEND_SHUTDOWN) &&
- sk_stream_memory_free(sk) &&
- vm_wait);
+ sk_wait_event(sk, ¤t_timeo, sk->sk_err ||
+ (sk->sk_shutdown & SEND_SHUTDOWN) ||
+ (sk_stream_memory_free(sk) &&
+ !vm_wait));
sk->sk_write_pending--;
if (vm_wait) {
diff --git a/net/ipv4/Kconfig b/net/ipv4/Kconfig
index 571f895..7cd7760 100644
--- a/net/ipv4/Kconfig
+++ b/net/ipv4/Kconfig
@@ -217,6 +217,7 @@
config NET_IPGRE
tristate "IP: GRE tunnels over IP"
+ depends on IPV6 || IPV6=n
help
Tunneling means encapsulating data of one protocol type within
another protocol and sending it over a channel that understands the
@@ -412,7 +413,7 @@
If unsure, say Y.
config INET_LRO
- bool "Large Receive Offload (ipv4/tcp)"
+ tristate "Large Receive Offload (ipv4/tcp)"
default y
---help---
Support for Large Receive Offload (ipv4/tcp).
diff --git a/net/ipv4/igmp.c b/net/ipv4/igmp.c
index 1fdcacd..2a4bb76 100644
--- a/net/ipv4/igmp.c
+++ b/net/ipv4/igmp.c
@@ -834,7 +834,7 @@
int mark = 0;
- if (len == 8 || IGMP_V2_SEEN(in_dev)) {
+ if (len == 8) {
if (ih->code == 0) {
/* Alas, old v1 router presents here. */
@@ -856,6 +856,18 @@
igmpv3_clear_delrec(in_dev);
} else if (len < 12) {
return; /* ignore bogus packet; freed by caller */
+ } else if (IGMP_V1_SEEN(in_dev)) {
+ /* This is a v3 query with v1 queriers present */
+ max_delay = IGMP_Query_Response_Interval;
+ group = 0;
+ } else if (IGMP_V2_SEEN(in_dev)) {
+ /* this is a v3 query with v2 queriers present;
+ * Interpretation of the max_delay code is problematic here.
+ * A real v2 host would use ih_code directly, while v3 has a
+ * different encoding. We use the v3 encoding as more likely
+ * to be intended in a v3 query.
+ */
+ max_delay = IGMPV3_MRC(ih3->code)*(HZ/IGMP_TIMER_SCALE);
} else { /* v3 */
if (!pskb_may_pull(skb, sizeof(struct igmpv3_query)))
return;
diff --git a/net/ipv4/tcp_timer.c b/net/ipv4/tcp_timer.c
index c35b469..74c54b3 100644
--- a/net/ipv4/tcp_timer.c
+++ b/net/ipv4/tcp_timer.c
@@ -135,13 +135,16 @@
/* This function calculates a "timeout" which is equivalent to the timeout of a
* TCP connection after "boundary" unsuccessful, exponentially backed-off
- * retransmissions with an initial RTO of TCP_RTO_MIN.
+ * retransmissions with an initial RTO of TCP_RTO_MIN or TCP_TIMEOUT_INIT if
+ * syn_set flag is set.
*/
static bool retransmits_timed_out(struct sock *sk,
- unsigned int boundary)
+ unsigned int boundary,
+ bool syn_set)
{
unsigned int timeout, linear_backoff_thresh;
unsigned int start_ts;
+ unsigned int rto_base = syn_set ? TCP_TIMEOUT_INIT : TCP_RTO_MIN;
if (!inet_csk(sk)->icsk_retransmits)
return false;
@@ -151,12 +154,12 @@
else
start_ts = tcp_sk(sk)->retrans_stamp;
- linear_backoff_thresh = ilog2(TCP_RTO_MAX/TCP_RTO_MIN);
+ linear_backoff_thresh = ilog2(TCP_RTO_MAX/rto_base);
if (boundary <= linear_backoff_thresh)
- timeout = ((2 << boundary) - 1) * TCP_RTO_MIN;
+ timeout = ((2 << boundary) - 1) * rto_base;
else
- timeout = ((2 << linear_backoff_thresh) - 1) * TCP_RTO_MIN +
+ timeout = ((2 << linear_backoff_thresh) - 1) * rto_base +
(boundary - linear_backoff_thresh) * TCP_RTO_MAX;
return (tcp_time_stamp - start_ts) >= timeout;
@@ -167,14 +170,15 @@
{
struct inet_connection_sock *icsk = inet_csk(sk);
int retry_until;
- bool do_reset;
+ bool do_reset, syn_set = 0;
if ((1 << sk->sk_state) & (TCPF_SYN_SENT | TCPF_SYN_RECV)) {
if (icsk->icsk_retransmits)
dst_negative_advice(sk);
retry_until = icsk->icsk_syn_retries ? : sysctl_tcp_syn_retries;
+ syn_set = 1;
} else {
- if (retransmits_timed_out(sk, sysctl_tcp_retries1)) {
+ if (retransmits_timed_out(sk, sysctl_tcp_retries1, 0)) {
/* Black hole detection */
tcp_mtu_probing(icsk, sk);
@@ -187,14 +191,14 @@
retry_until = tcp_orphan_retries(sk, alive);
do_reset = alive ||
- !retransmits_timed_out(sk, retry_until);
+ !retransmits_timed_out(sk, retry_until, 0);
if (tcp_out_of_resources(sk, do_reset))
return 1;
}
}
- if (retransmits_timed_out(sk, retry_until)) {
+ if (retransmits_timed_out(sk, retry_until, syn_set)) {
/* Has it gone just too far? */
tcp_write_err(sk);
return 1;
@@ -436,7 +440,7 @@
icsk->icsk_rto = min(icsk->icsk_rto << 1, TCP_RTO_MAX);
}
inet_csk_reset_xmit_timer(sk, ICSK_TIME_RETRANS, icsk->icsk_rto, TCP_RTO_MAX);
- if (retransmits_timed_out(sk, sysctl_tcp_retries1 + 1))
+ if (retransmits_timed_out(sk, sysctl_tcp_retries1 + 1, 0))
__sk_dst_reset(sk);
out:;
diff --git a/net/ipv6/route.c b/net/ipv6/route.c
index 8323136..a275c6e 100644
--- a/net/ipv6/route.c
+++ b/net/ipv6/route.c
@@ -1556,14 +1556,13 @@
* i.e. Path MTU discovery
*/
-void rt6_pmtu_discovery(struct in6_addr *daddr, struct in6_addr *saddr,
- struct net_device *dev, u32 pmtu)
+static void rt6_do_pmtu_disc(struct in6_addr *daddr, struct in6_addr *saddr,
+ struct net *net, u32 pmtu, int ifindex)
{
struct rt6_info *rt, *nrt;
- struct net *net = dev_net(dev);
int allfrag = 0;
- rt = rt6_lookup(net, daddr, saddr, dev->ifindex, 0);
+ rt = rt6_lookup(net, daddr, saddr, ifindex, 0);
if (rt == NULL)
return;
@@ -1631,6 +1630,27 @@
dst_release(&rt->dst);
}
+void rt6_pmtu_discovery(struct in6_addr *daddr, struct in6_addr *saddr,
+ struct net_device *dev, u32 pmtu)
+{
+ struct net *net = dev_net(dev);
+
+ /*
+ * RFC 1981 states that a node "MUST reduce the size of the packets it
+ * is sending along the path" that caused the Packet Too Big message.
+ * Since it's not possible in the general case to determine which
+ * interface was used to send the original packet, we update the MTU
+ * on the interface that will be used to send future packets. We also
+ * update the MTU on the interface that received the Packet Too Big in
+ * case the original packet was forced out that interface with
+ * SO_BINDTODEVICE or similar. This is the next best thing to the
+ * correct behaviour, which would be to update the MTU on all
+ * interfaces.
+ */
+ rt6_do_pmtu_disc(daddr, saddr, net, pmtu, 0);
+ rt6_do_pmtu_disc(daddr, saddr, net, pmtu, dev->ifindex);
+}
+
/*
* Misc support functions
*/
diff --git a/net/mac80211/agg-tx.c b/net/mac80211/agg-tx.c
index c893f23..8f23401 100644
--- a/net/mac80211/agg-tx.c
+++ b/net/mac80211/agg-tx.c
@@ -175,6 +175,8 @@
set_bit(HT_AGG_STATE_STOPPING, &tid_tx->state);
+ del_timer_sync(&tid_tx->addba_resp_timer);
+
/*
* After this packets are no longer handed right through
* to the driver but are put onto tid_tx->pending instead,
diff --git a/net/mac80211/rx.c b/net/mac80211/rx.c
index fa0f37e..28624282 100644
--- a/net/mac80211/rx.c
+++ b/net/mac80211/rx.c
@@ -2199,9 +2199,6 @@
struct net_device *prev_dev = NULL;
struct ieee80211_rx_status *status = IEEE80211_SKB_RXCB(skb);
- if (status->flag & RX_FLAG_INTERNAL_CMTR)
- goto out_free_skb;
-
if (skb_headroom(skb) < sizeof(*rthdr) &&
pskb_expand_head(skb, sizeof(*rthdr), 0, GFP_ATOMIC))
goto out_free_skb;
@@ -2260,7 +2257,6 @@
} else
goto out_free_skb;
- status->flag |= RX_FLAG_INTERNAL_CMTR;
return;
out_free_skb:
diff --git a/net/mac80211/status.c b/net/mac80211/status.c
index 10caec5..34da679 100644
--- a/net/mac80211/status.c
+++ b/net/mac80211/status.c
@@ -377,7 +377,7 @@
skb2 = skb_clone(skb, GFP_ATOMIC);
if (skb2) {
skb2->dev = prev_dev;
- netif_receive_skb(skb2);
+ netif_rx(skb2);
}
}
@@ -386,7 +386,7 @@
}
if (prev_dev) {
skb->dev = prev_dev;
- netif_receive_skb(skb);
+ netif_rx(skb);
skb = NULL;
}
rcu_read_unlock();
diff --git a/net/phonet/pep.c b/net/phonet/pep.c
index b2a3ae6..1500302 100644
--- a/net/phonet/pep.c
+++ b/net/phonet/pep.c
@@ -225,12 +225,13 @@
static int pipe_rcv_status(struct sock *sk, struct sk_buff *skb)
{
struct pep_sock *pn = pep_sk(sk);
- struct pnpipehdr *hdr = pnp_hdr(skb);
+ struct pnpipehdr *hdr;
int wake = 0;
if (!pskb_may_pull(skb, sizeof(*hdr) + 4))
return -EINVAL;
+ hdr = pnp_hdr(skb);
if (hdr->data[0] != PN_PEP_TYPE_COMMON) {
LIMIT_NETDEBUG(KERN_DEBUG"Phonet unknown PEP type: %u\n",
(unsigned)hdr->data[0]);
diff --git a/net/rds/page.c b/net/rds/page.c
index 595a952..1dfbfea 100644
--- a/net/rds/page.c
+++ b/net/rds/page.c
@@ -57,30 +57,17 @@
unsigned long ret;
void *addr;
- if (to_user)
+ addr = kmap(page);
+ if (to_user) {
rds_stats_add(s_copy_to_user, bytes);
- else
+ ret = copy_to_user(ptr, addr + offset, bytes);
+ } else {
rds_stats_add(s_copy_from_user, bytes);
-
- addr = kmap_atomic(page, KM_USER0);
- if (to_user)
- ret = __copy_to_user_inatomic(ptr, addr + offset, bytes);
- else
- ret = __copy_from_user_inatomic(addr + offset, ptr, bytes);
- kunmap_atomic(addr, KM_USER0);
-
- if (ret) {
- addr = kmap(page);
- if (to_user)
- ret = copy_to_user(ptr, addr + offset, bytes);
- else
- ret = copy_from_user(addr + offset, ptr, bytes);
- kunmap(page);
- if (ret)
- return -EFAULT;
+ ret = copy_from_user(addr + offset, ptr, bytes);
}
+ kunmap(page);
- return 0;
+ return ret ? -EFAULT : 0;
}
EXPORT_SYMBOL_GPL(rds_page_copy_user);
diff --git a/net/sched/cls_u32.c b/net/sched/cls_u32.c
index 7416a5c..b0c2a82 100644
--- a/net/sched/cls_u32.c
+++ b/net/sched/cls_u32.c
@@ -137,7 +137,7 @@
int toff = off + key->off + (off2 & key->offmask);
__be32 *data, _data;
- if (skb_headroom(skb) + toff < 0)
+ if (skb_headroom(skb) + toff > INT_MAX)
goto out;
data = skb_header_pointer(skb, toff, 4, &_data);
diff --git a/net/sctp/auth.c b/net/sctp/auth.c
index 8636639..ddbbf7c 100644
--- a/net/sctp/auth.c
+++ b/net/sctp/auth.c
@@ -543,16 +543,20 @@
id = ntohs(hmacs->hmac_ids[i]);
/* Check the id is in the supported range */
- if (id > SCTP_AUTH_HMAC_ID_MAX)
+ if (id > SCTP_AUTH_HMAC_ID_MAX) {
+ id = 0;
continue;
+ }
/* See is we support the id. Supported IDs have name and
* length fields set, so that we can allocated and use
* them. We can safely just check for name, for without the
* name, we can't allocate the TFM.
*/
- if (!sctp_hmac_list[id].hmac_name)
+ if (!sctp_hmac_list[id].hmac_name) {
+ id = 0;
continue;
+ }
break;
}
diff --git a/net/sctp/socket.c b/net/sctp/socket.c
index ca44917..fbb7077 100644
--- a/net/sctp/socket.c
+++ b/net/sctp/socket.c
@@ -916,6 +916,11 @@
/* Walk through the addrs buffer and count the number of addresses. */
addr_buf = kaddrs;
while (walk_size < addrs_size) {
+ if (walk_size + sizeof(sa_family_t) > addrs_size) {
+ kfree(kaddrs);
+ return -EINVAL;
+ }
+
sa_addr = (struct sockaddr *)addr_buf;
af = sctp_get_af_specific(sa_addr->sa_family);
@@ -1002,9 +1007,13 @@
/* Walk through the addrs buffer and count the number of addresses. */
addr_buf = kaddrs;
while (walk_size < addrs_size) {
+ if (walk_size + sizeof(sa_family_t) > addrs_size) {
+ err = -EINVAL;
+ goto out_free;
+ }
+
sa_addr = (union sctp_addr *)addr_buf;
af = sctp_get_af_specific(sa_addr->sa.sa_family);
- port = ntohs(sa_addr->v4.sin_port);
/* If the address family is not supported or if this address
* causes the address buffer to overflow return EINVAL.
@@ -1014,6 +1023,8 @@
goto out_free;
}
+ port = ntohs(sa_addr->v4.sin_port);
+
/* Save current address so we can work with it */
memcpy(&to, sa_addr, af->sockaddr_len);
diff --git a/scripts/kconfig/conf.c b/scripts/kconfig/conf.c
index 5b7c86e..7ef429c 100644
--- a/scripts/kconfig/conf.c
+++ b/scripts/kconfig/conf.c
@@ -427,7 +427,7 @@
if (sym->name && !sym_is_choice_value(sym)) {
printf("CONFIG_%s\n", sym->name);
}
- } else {
+ } else if (input_mode != oldnoconfig) {
if (!conf_cnt++)
printf(_("*\n* Restart config...\n*\n"));
rootEntry = menu_get_parent_menu(menu);
diff --git a/scripts/kconfig/expr.h b/scripts/kconfig/expr.h
index 6ee2e4f..170459c 100644
--- a/scripts/kconfig/expr.h
+++ b/scripts/kconfig/expr.h
@@ -165,7 +165,6 @@
struct symbol *sym;
struct property *prompt;
struct expr *dep;
- struct expr *dir_dep;
unsigned int flags;
char *help;
struct file *file;
diff --git a/scripts/kconfig/menu.c b/scripts/kconfig/menu.c
index 4fb5902..edda8b4 100644
--- a/scripts/kconfig/menu.c
+++ b/scripts/kconfig/menu.c
@@ -107,7 +107,6 @@
void menu_add_dep(struct expr *dep)
{
current_entry->dep = expr_alloc_and(current_entry->dep, menu_check_dep(dep));
- current_entry->dir_dep = current_entry->dep;
}
void menu_set_type(int type)
@@ -291,10 +290,6 @@
for (menu = parent->list; menu; menu = menu->next)
menu_finalize(menu);
} else if (sym) {
- /* ignore inherited dependencies for dir_dep */
- sym->dir_dep.expr = expr_transform(expr_copy(parent->dir_dep));
- sym->dir_dep.expr = expr_eliminate_dups(sym->dir_dep.expr);
-
basedep = parent->prompt ? parent->prompt->visible.expr : NULL;
basedep = expr_trans_compare(basedep, E_UNEQUAL, &symbol_no);
basedep = expr_eliminate_dups(expr_transform(basedep));
@@ -325,6 +320,8 @@
parent->next = last_menu->next;
last_menu->next = NULL;
}
+
+ sym->dir_dep.expr = parent->dep;
}
for (menu = parent->list; menu; menu = menu->next) {
if (sym && sym_is_choice(sym) &&
diff --git a/scripts/kconfig/symbol.c b/scripts/kconfig/symbol.c
index 943712c..1f8b305 100644
--- a/scripts/kconfig/symbol.c
+++ b/scripts/kconfig/symbol.c
@@ -350,6 +350,7 @@
}
}
calc_newval:
+#if 0
if (sym->dir_dep.tri == no && sym->rev_dep.tri != no) {
fprintf(stderr, "warning: (");
expr_fprint(sym->rev_dep.expr, stderr);
@@ -358,6 +359,7 @@
expr_fprint(sym->dir_dep.expr, stderr);
fprintf(stderr, ")\n");
}
+#endif
newval.tri = EXPR_OR(newval.tri, sym->rev_dep.tri);
}
if (newval.tri == mod && sym_get_type(sym) == S_BOOLEAN)
diff --git a/sound/core/control.c b/sound/core/control.c
index 070aab4..45a8180 100644
--- a/sound/core/control.c
+++ b/sound/core/control.c
@@ -31,6 +31,7 @@
/* max number of user-defined controls */
#define MAX_USER_CONTROLS 32
+#define MAX_CONTROL_COUNT 1028
struct snd_kctl_ioctl {
struct list_head list; /* list of all ioctls */
@@ -195,6 +196,10 @@
if (snd_BUG_ON(!control || !control->count))
return NULL;
+
+ if (control->count > MAX_CONTROL_COUNT)
+ return NULL;
+
kctl = kzalloc(sizeof(*kctl) + sizeof(struct snd_kcontrol_volatile) * control->count, GFP_KERNEL);
if (kctl == NULL) {
snd_printk(KERN_ERR "Cannot allocate control instance\n");
diff --git a/sound/core/rawmidi.c b/sound/core/rawmidi.c
index a7868ad..cbbed0d 100644
--- a/sound/core/rawmidi.c
+++ b/sound/core/rawmidi.c
@@ -535,13 +535,15 @@
{
struct snd_rawmidi_file *rfile;
struct snd_rawmidi *rmidi;
+ struct module *module;
rfile = file->private_data;
rmidi = rfile->rmidi;
rawmidi_release_priv(rfile);
kfree(rfile);
+ module = rmidi->card->module;
snd_card_file_remove(rmidi->card, file);
- module_put(rmidi->card->module);
+ module_put(module);
return 0;
}
diff --git a/sound/i2c/other/ak4xxx-adda.c b/sound/i2c/other/ak4xxx-adda.c
index 1adb8a3..42d7844 100644
--- a/sound/i2c/other/ak4xxx-adda.c
+++ b/sound/i2c/other/ak4xxx-adda.c
@@ -900,7 +900,7 @@
return 0;
}
#else /* !CONFIG_PROC_FS */
-static int proc_init(struct snd_akm4xxx *ak) {}
+static int proc_init(struct snd_akm4xxx *ak) { return 0; }
#endif
int snd_akm4xxx_build_controls(struct snd_akm4xxx *ak)
diff --git a/sound/oss/soundcard.c b/sound/oss/soundcard.c
index 92aa762..07f803e 100644
--- a/sound/oss/soundcard.c
+++ b/sound/oss/soundcard.c
@@ -391,11 +391,11 @@
case SND_DEV_DSP:
case SND_DEV_DSP16:
case SND_DEV_AUDIO:
- return audio_ioctl(dev, file, cmd, p);
+ ret = audio_ioctl(dev, file, cmd, p);
break;
case SND_DEV_MIDIN:
- return MIDIbuf_ioctl(dev, file, cmd, p);
+ ret = MIDIbuf_ioctl(dev, file, cmd, p);
break;
}
diff --git a/sound/pci/hda/patch_sigmatel.c b/sound/pci/hda/patch_sigmatel.c
index 95148e5..c16c5ba 100644
--- a/sound/pci/hda/patch_sigmatel.c
+++ b/sound/pci/hda/patch_sigmatel.c
@@ -1747,6 +1747,8 @@
"HP dv6", STAC_HP_DV5),
SND_PCI_QUIRK(PCI_VENDOR_ID_HP, 0x3061,
"HP dv6", STAC_HP_DV5), /* HP dv6-1110ax */
+ SND_PCI_QUIRK(PCI_VENDOR_ID_HP, 0x363e,
+ "HP DV6", STAC_HP_DV5),
SND_PCI_QUIRK_MASK(PCI_VENDOR_ID_HP, 0xfff0, 0x7010,
"HP", STAC_HP_DV5),
SND_PCI_QUIRK(PCI_VENDOR_ID_DELL, 0x0233,
diff --git a/tools/perf/Makefile b/tools/perf/Makefile
index 4f1fa77..1950e19 100644
--- a/tools/perf/Makefile
+++ b/tools/perf/Makefile
@@ -1017,7 +1017,7 @@
# we compile into subdirectories. if the target directory is not the source directory, they might not exists. So
# we depend the various files onto their directories.
DIRECTORY_DEPS = $(LIB_OBJS) $(BUILTIN_OBJS) $(OUTPUT)PERF-VERSION-FILE $(OUTPUT)common-cmds.h
-$(DIRECTORY_DEPS): $(sort $(dir $(DIRECTORY_DEPS)))
+$(DIRECTORY_DEPS): | $(sort $(dir $(DIRECTORY_DEPS)))
# In the second step, we make a rule to actually create these directories
$(sort $(dir $(DIRECTORY_DEPS))):
$(QUIET_MKDIR)$(MKDIR) -p $@ 2>/dev/null
diff --git a/tools/perf/perf.h b/tools/perf/perf.h
index ef7aa0a..95aaf56 100644
--- a/tools/perf/perf.h
+++ b/tools/perf/perf.h
@@ -73,6 +73,18 @@
#define cpu_relax() asm volatile("":::"memory")
#endif
+#ifdef __mips__
+#include "../../arch/mips/include/asm/unistd.h"
+#define rmb() asm volatile( \
+ ".set mips2\n\t" \
+ "sync\n\t" \
+ ".set mips0" \
+ : /* no output */ \
+ : /* no input */ \
+ : "memory")
+#define cpu_relax() asm volatile("" ::: "memory")
+#endif
+
#include <time.h>
#include <unistd.h>
#include <sys/types.h>
diff --git a/tools/perf/util/trace-event-scripting.c b/tools/perf/util/trace-event-scripting.c
index 7ea983a..f7af2fc 100644
--- a/tools/perf/util/trace-event-scripting.c
+++ b/tools/perf/util/trace-event-scripting.c
@@ -97,7 +97,7 @@
register_python_scripting(&python_scripting_unsupported_ops);
}
#else
-struct scripting_ops python_scripting_ops;
+extern struct scripting_ops python_scripting_ops;
void setup_python_scripting(void)
{
@@ -158,7 +158,7 @@
register_perl_scripting(&perl_scripting_unsupported_ops);
}
#else
-struct scripting_ops perl_scripting_ops;
+extern struct scripting_ops perl_scripting_ops;
void setup_perl_scripting(void)
{
diff --git a/tools/perf/util/ui/browsers/hists.c b/tools/perf/util/ui/browsers/hists.c
index dafdf67..6866aa4 100644
--- a/tools/perf/util/ui/browsers/hists.c
+++ b/tools/perf/util/ui/browsers/hists.c
@@ -773,7 +773,7 @@
switch (key) {
case 'a':
- if (browser->selection->map == NULL &&
+ if (browser->selection->map == NULL ||
browser->selection->map->dso->annotate_warned)
continue;
goto do_annotate;