powerpc: Merge 32 and 64-bit dma code
We essentially adopt the 64-bit dma code, with some changes to support
32-bit systems, including HIGHMEM. dma functions on 32-bit are now
invoked via accessor functions which call the correct op for a device based
on archdata dma_ops. If there is no archdata dma_ops, this defaults
to dma_direct_ops.
In addition, the dma_map/unmap_page functions are added to dma_ops
because we can't just fall back on map/unmap_single when HIGHMEM is
enabled. In the case of dma_direct_*, we stop using map/unmap_single
and just use the page version - this saves a lot of ugly
ifdeffing. We leave map/unmap_single in the dma_ops definition,
though, because they are needed by the iommu code, which does not
implement map/unmap_page. Ideally, going forward, we will completely
eliminate map/unmap_single and just have map/unmap_page, if it's
workable for 64-bit.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
diff --git a/arch/powerpc/kernel/pci-common.c b/arch/powerpc/kernel/pci-common.c
index ea0c61e..52ccfed4 100644
--- a/arch/powerpc/kernel/pci-common.c
+++ b/arch/powerpc/kernel/pci-common.c
@@ -56,6 +56,34 @@
/* Default PCI flags is 0 */
unsigned int ppc_pci_flags;
+static struct dma_mapping_ops *pci_dma_ops;
+
+void set_pci_dma_ops(struct dma_mapping_ops *dma_ops)
+{
+ pci_dma_ops = dma_ops;
+}
+
+struct dma_mapping_ops *get_pci_dma_ops(void)
+{
+ return pci_dma_ops;
+}
+EXPORT_SYMBOL(get_pci_dma_ops);
+
+int pci_set_dma_mask(struct pci_dev *dev, u64 mask)
+{
+ return dma_set_mask(&dev->dev, mask);
+}
+
+int pci_set_consistent_dma_mask(struct pci_dev *dev, u64 mask)
+{
+ int rc;
+
+ rc = dma_set_mask(&dev->dev, mask);
+ dev->dev.coherent_dma_mask = dev->dma_mask;
+
+ return rc;
+}
+
struct pci_controller *pcibios_alloc_controller(struct device_node *dev)
{
struct pci_controller *phb;
@@ -180,6 +208,26 @@
return str;
}
+void __devinit pcibios_setup_new_device(struct pci_dev *dev)
+{
+ struct dev_archdata *sd = &dev->dev.archdata;
+
+ sd->of_node = pci_device_to_OF_node(dev);
+
+ DBG("PCI: device %s OF node: %s\n", pci_name(dev),
+ sd->of_node ? sd->of_node->full_name : "<none>");
+
+ sd->dma_ops = pci_dma_ops;
+#ifdef CONFIG_PPC32
+ sd->dma_data = (void *)PCI_DRAM_OFFSET;
+#endif
+ set_dev_node(&dev->dev, pcibus_to_node(dev->bus));
+
+ if (ppc_md.pci_dma_dev_setup)
+ ppc_md.pci_dma_dev_setup(dev);
+}
+EXPORT_SYMBOL(pcibios_setup_new_device);
+
/*
* Reads the interrupt pin to determine if interrupt is use by card.
* If the interrupt is used, then gets the interrupt line from the