USB: serial: ssu100.c: remove dbg() usage
dbg() was a very old USB-serial-specific macro.
This patch removes it from being used in the
driver and uses dev_dbg() instead.
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
diff --git a/drivers/usb/serial/ssu100.c b/drivers/usb/serial/ssu100.c
index 3fee23b..e719661 100644
--- a/drivers/usb/serial/ssu100.c
+++ b/drivers/usb/serial/ssu100.c
@@ -135,7 +135,7 @@
int result;
if (((set | clear) & (TIOCM_DTR | TIOCM_RTS)) == 0) {
- dbg("%s - DTR|RTS not being set|cleared", __func__);
+ dev_dbg(&dev->dev, "%s - DTR|RTS not being set|cleared\n", __func__);
return 0; /* no change */
}
@@ -148,7 +148,7 @@
result = ssu100_setregister(dev, 0, UART_MCR, urb_value);
if (result < 0)
- dbg("%s Error from MODEM_CTRL urb", __func__);
+ dev_dbg(&dev->dev, "%s Error from MODEM_CTRL urb\n", __func__);
return result;
}
@@ -164,7 +164,7 @@
result = ssu100_getdevice(dev, data);
if (result < 0) {
- dbg("%s - get_device failed %i", __func__, result);
+ dev_dbg(&dev->dev, "%s - get_device failed %i\n", __func__, result);
goto out;
}
@@ -172,25 +172,25 @@
result = ssu100_setdevice(dev, data);
if (result < 0) {
- dbg("%s - setdevice failed %i", __func__, result);
+ dev_dbg(&dev->dev, "%s - setdevice failed %i\n", __func__, result);
goto out;
}
result = ssu100_control_msg(dev, QT_GET_SET_PREBUF_TRIG_LVL, 128, 0);
if (result < 0) {
- dbg("%s - set prebuffer level failed %i", __func__, result);
+ dev_dbg(&dev->dev, "%s - set prebuffer level failed %i\n", __func__, result);
goto out;
}
result = ssu100_control_msg(dev, QT_SET_ATF, ATC_DISABLED, 0);
if (result < 0) {
- dbg("%s - set ATFprebuffer level failed %i", __func__, result);
+ dev_dbg(&dev->dev, "%s - set ATFprebuffer level failed %i\n", __func__, result);
goto out;
}
result = ssu100_getdevice(dev, data);
if (result < 0) {
- dbg("%s - get_device failed %i", __func__, result);
+ dev_dbg(&dev->dev, "%s - get_device failed %i\n", __func__, result);
goto out;
}
@@ -201,7 +201,7 @@
result = ssu100_setdevice(dev, data);
if (result < 0) {
- dbg("%s - setdevice failed %i", __func__, result);
+ dev_dbg(&dev->dev, "%s - setdevice failed %i\n", __func__, result);
goto out;
}
@@ -249,7 +249,7 @@
if (!baud)
baud = 9600;
- dbg("%s - got baud = %d\n", __func__, baud);
+ dev_dbg(&port->dev, "%s - got baud = %d\n", __func__, baud);
divisor = MAX_BAUD_RATE / baud;
@@ -261,7 +261,7 @@
result = ssu100_control_msg(dev, QT_GET_SET_UART, divisor, urb_value);
if (result < 0)
- dbg("%s - set uart failed", __func__);
+ dev_dbg(&port->dev, "%s - set uart failed\n", __func__);
if (cflag & CRTSCTS)
result = ssu100_control_msg(dev, QT_HW_FLOW_CONTROL_MASK,
@@ -270,7 +270,7 @@
result = ssu100_control_msg(dev, QT_HW_FLOW_CONTROL_MASK,
0, 0);
if (result < 0)
- dbg("%s - set HW flow control failed", __func__);
+ dev_dbg(&port->dev, "%s - set HW flow control failed\n", __func__);
if (I_IXOFF(tty) || I_IXON(tty)) {
u16 x = ((u16)(START_CHAR(tty) << 8) | (u16)(STOP_CHAR(tty)));
@@ -282,7 +282,7 @@
0, 0);
if (result < 0)
- dbg("%s - set SW flow control failed", __func__);
+ dev_dbg(&port->dev, "%s - set SW flow control failed\n", __func__);
}
@@ -304,7 +304,7 @@
QT_TRANSFER_IN, 0x01,
0, data, 2, 300);
if (result < 0) {
- dbg("%s - open failed %i", __func__, result);
+ dev_dbg(&port->dev, "%s - open failed %i\n", __func__, result);
kfree(data);
return result;
}
@@ -319,7 +319,7 @@
/* set to 9600 */
result = ssu100_control_msg(dev, QT_GET_SET_UART, 0x30, 0x0300);
if (result < 0)
- dbg("%s - set uart failed", __func__);
+ dev_dbg(&port->dev, "%s - set uart failed\n", __func__);
if (tty)
ssu100_set_termios(tty, port, tty->termios);
@@ -423,7 +423,7 @@
{
struct usb_serial_port *port = tty->driver_data;
- dbg("%s cmd 0x%04x", __func__, cmd);
+ dev_dbg(&port->dev, "%s cmd 0x%04x\n", __func__, cmd);
switch (cmd) {
case TIOCGSERIAL:
@@ -437,7 +437,7 @@
break;
}
- dbg("%s arg not supported", __func__);
+ dev_dbg(&port->dev, "%s arg not supported\n", __func__);
return -ENOIOCTLCMD;
}