x86: multi pci root bus with different io resource range, on 64-bit
scan AMD opteron io/mmio routing to make sure every pci root bus get correct
resource range. Thus later pci scan could assign correct resource to device
with unassigned resource.
this can fix a system without _CRS for multi pci root bus.
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
diff --git a/arch/x86/pci/k8-bus_64.c b/arch/x86/pci/k8-bus_64.c
index dab3831..5e8a9d1 100644
--- a/arch/x86/pci/k8-bus_64.c
+++ b/arch/x86/pci/k8-bus_64.c
@@ -7,23 +7,29 @@
/*
* This discovers the pcibus <-> node mapping on AMD K8.
- *
- * RED-PEN need to call this again on PCI hotplug
- * RED-PEN empty cpus get reported wrong
+ * also get peer root bus resource for io,mmio
*/
-#define NODE_ID(dword) ((dword>>4) & 0x07)
-#define LDT_BUS_NUMBER_REGISTER_0 0xE0
-#define LDT_BUS_NUMBER_REGISTER_1 0xE4
-#define LDT_BUS_NUMBER_REGISTER_2 0xE8
-#define LDT_BUS_NUMBER_REGISTER_3 0xEC
-#define NR_LDT_BUS_NUMBER_REGISTERS 4
-#define SECONDARY_LDT_BUS_NUMBER(dword) ((dword >> 16) & 0xFF)
-#define SUBORDINATE_LDT_BUS_NUMBER(dword) ((dword >> 24) & 0xFF)
-#define PCI_DEVICE_ID_K8HTCONFIG 0x1100
-#define PCI_DEVICE_ID_K8_10H_HTCONFIG 0x1200
-#define PCI_DEVICE_ID_K8_11H_HTCONFIG 0x1300
+/*
+ * sub bus (transparent) will use entres from 3 to store extra from root,
+ * so need to make sure have enought slot there, increase PCI_BUS_NUM_RESOURCES?
+ */
+#define RES_NUM 16
+struct pci_root_info {
+ char name[12];
+ unsigned int res_num;
+ struct resource res[RES_NUM];
+ int bus_min;
+ int bus_max;
+ int node;
+ int link;
+};
+
+/* 4 at this time, it may become to 32 */
+#define PCI_ROOT_NR 4
+static int pci_root_num;
+static struct pci_root_info pci_root_info[PCI_ROOT_NR];
#ifdef CONFIG_NUMA
@@ -55,77 +61,375 @@
return node;
}
-
#endif
+void set_pci_bus_resources_arch_default(struct pci_bus *b)
+{
+ int i;
+ int j;
+ struct pci_root_info *info;
+
+ if (!pci_root_num)
+ return;
+
+ for (i = 0; i < pci_root_num; i++) {
+ if (pci_root_info[i].bus_min == b->number)
+ break;
+ }
+
+ if (i == pci_root_num)
+ return;
+
+ info = &pci_root_info[i];
+ for (j = 0; j < info->res_num; j++) {
+ struct resource *res;
+ struct resource *root;
+
+ res = &info->res[j];
+ b->resource[j] = res;
+ if (res->flags & IORESOURCE_IO)
+ root = &ioport_resource;
+ else
+ root = &iomem_resource;
+ insert_resource(root, res);
+ }
+}
+
+#define RANGE_NUM 16
+
+struct res_range {
+ size_t start;
+ size_t end;
+};
+
+static void __init update_range(struct res_range *range, size_t start,
+ size_t end)
+{
+ int i;
+ int j;
+
+ for (j = 0; j < RANGE_NUM; j++) {
+ if (!range[j].end)
+ continue;
+ if (start == range[j].start && end < range[j].end) {
+ range[j].start = end + 1;
+ break;
+ } else if (start == range[j].start && end == range[j].end) {
+ range[j].start = 0;
+ range[j].end = 0;
+ break;
+ } else if (start > range[j].start && end == range[j].end) {
+ range[j].end = start - 1;
+ break;
+ } else if (start > range[j].start && end < range[j].end) {
+ /* find the new spare */
+ for (i = 0; i < RANGE_NUM; i++) {
+ if (range[i].end == 0)
+ break;
+ }
+ if (i < RANGE_NUM) {
+ range[i].end = range[j].end;
+ range[i].start = end + 1;
+ } else {
+ printk(KERN_ERR "run of slot in ranges\n");
+ }
+ range[j].end = start - 1;
+ break;
+ }
+ }
+}
+
+static void __init update_res(struct pci_root_info *info, size_t start,
+ size_t end, unsigned long flags, int merge)
+{
+ int i;
+ struct resource *res;
+
+ if (!merge)
+ goto addit;
+
+ /* try to merge it with old one */
+ for (i = 0; i < info->res_num; i++) {
+ res = &info->res[i];
+ if (res->flags != flags)
+ continue;
+ if (res->end + 1 == start) {
+ res->end = end;
+ return;
+ } else if (end + 1 == res->start) {
+ res->start = start;
+ return;
+ }
+ }
+
+addit:
+
+ /* need to add that */
+ if (info->res_num >= RES_NUM)
+ return;
+
+ res = &info->res[info->res_num];
+ res->name = info->name;
+ res->flags = flags;
+ res->start = start;
+ res->end = end;
+ res->child = NULL;
+ info->res_num++;
+}
+
+struct pci_hostbridge_probe {
+ u32 bus;
+ u32 slot;
+ u32 vendor;
+ u32 device;
+};
+
+static struct pci_hostbridge_probe pci_probes[] __initdata = {
+ { 0, 0x18, PCI_VENDOR_ID_AMD, 0x1100 },
+ { 0, 0x18, PCI_VENDOR_ID_AMD, 0x1200 },
+ { 0xff, 0, PCI_VENDOR_ID_AMD, 0x1200 },
+ { 0, 0x18, PCI_VENDOR_ID_AMD, 0x1300 },
+};
+
/**
* early_fill_mp_bus_to_node()
* called before pcibios_scan_root and pci_scan_bus
* fills the mp_bus_to_cpumask array based according to the LDT Bus Number
* Registers found in the K8 northbridge
*/
-__init static int
-early_fill_mp_bus_to_node(void)
+static int __init early_fill_mp_bus_info(void)
{
-#ifdef CONFIG_NUMA
- int i, j;
+ int i;
+ int j;
+ unsigned bus;
unsigned slot;
- u32 ldtbus;
- u32 id;
+ int found;
int node;
- u16 deviceid;
- u16 vendorid;
- int min_bus;
- int max_bus;
+ int link;
+ int def_node;
+ int def_link;
+ struct pci_root_info *info;
+ u32 reg;
+ struct resource *res;
+ size_t start;
+ size_t end;
+ struct res_range range[RANGE_NUM];
+ u64 val;
+ u32 address;
- static int lbnr[NR_LDT_BUS_NUMBER_REGISTERS] = {
- LDT_BUS_NUMBER_REGISTER_0,
- LDT_BUS_NUMBER_REGISTER_1,
- LDT_BUS_NUMBER_REGISTER_2,
- LDT_BUS_NUMBER_REGISTER_3
- };
-
+#ifdef CONFIG_NUMA
for (i = 0; i < BUS_NR; i++)
mp_bus_to_node[i] = -1;
+#endif
if (!early_pci_allowed())
return -1;
- slot = 0x18;
- id = read_pci_config(0, slot, 0, PCI_VENDOR_ID);
+ found = 0;
+ for (i = 0; i < ARRAY_SIZE(pci_probes); i++) {
+ u32 id;
+ u16 device;
+ u16 vendor;
- vendorid = id & 0xffff;
- if (vendorid != PCI_VENDOR_ID_AMD)
- goto out;
+ bus = pci_probes[i].bus;
+ slot = pci_probes[i].slot;
+ id = read_pci_config(bus, slot, 0, PCI_VENDOR_ID);
- deviceid = (id>>16) & 0xffff;
- if ((deviceid != PCI_DEVICE_ID_K8HTCONFIG) &&
- (deviceid != PCI_DEVICE_ID_K8_10H_HTCONFIG) &&
- (deviceid != PCI_DEVICE_ID_K8_11H_HTCONFIG))
- goto out;
-
- for (i = 0; i < NR_LDT_BUS_NUMBER_REGISTERS; i++) {
- ldtbus = read_pci_config(0, slot, 1, lbnr[i]);
-
- /* Check if that register is enabled for bus range */
- if ((ldtbus & 7) != 3)
- continue;
-
- min_bus = SECONDARY_LDT_BUS_NUMBER(ldtbus);
- max_bus = SUBORDINATE_LDT_BUS_NUMBER(ldtbus);
- node = NODE_ID(ldtbus);
- for (j = min_bus; j <= max_bus; j++)
- mp_bus_to_node[j] = (unsigned char) node;
+ vendor = id & 0xffff;
+ device = (id>>16) & 0xffff;
+ if (pci_probes[i].vendor == vendor &&
+ pci_probes[i].device == device) {
+ found = 1;
+ break;
+ }
}
-out:
+ if (!found)
+ return 0;
+
+ pci_root_num = 0;
+ for (i = 0; i < 4; i++) {
+ int min_bus;
+ int max_bus;
+ reg = read_pci_config(bus, slot, 1, 0xe0 + (i << 2));
+
+ /* Check if that register is enabled for bus range */
+ if ((reg & 7) != 3)
+ continue;
+
+ min_bus = (reg >> 16) & 0xff;
+ max_bus = (reg >> 24) & 0xff;
+ node = (reg >> 4) & 0x07;
+#ifdef CONFIG_NUMA
+ for (j = min_bus; j <= max_bus; j++)
+ mp_bus_to_node[j] = (unsigned char) node;
+#endif
+ link = (reg >> 8) & 0x03;
+
+ info = &pci_root_info[pci_root_num];
+ info->bus_min = min_bus;
+ info->bus_max = max_bus;
+ info->node = node;
+ info->link = link;
+ sprintf(info->name, "PCI Bus #%02x", min_bus);
+ pci_root_num++;
+ }
+
+ /* get the default node and link for left over res */
+ reg = read_pci_config(bus, slot, 0, 0x60);
+ def_node = (reg >> 8) & 0x07;
+ reg = read_pci_config(bus, slot, 0, 0x64);
+ def_link = (reg >> 8) & 0x03;
+
+ memset(range, 0, sizeof(range));
+ range[0].end = 0xffff;
+ /* io port resource */
+ for (i = 0; i < 4; i++) {
+ reg = read_pci_config(bus, slot, 1, 0xc0 + (i << 3));
+ if (!(reg & 3))
+ continue;
+
+ start = reg & 0xfff000;
+ reg = read_pci_config(bus, slot, 1, 0xc4 + (i << 3));
+ node = reg & 0x07;
+ link = (reg >> 4) & 0x03;
+ end = (reg & 0xfff000) | 0xfff;
+
+ /* find the position */
+ for (j = 0; j < pci_root_num; j++) {
+ info = &pci_root_info[j];
+ if (info->node == node && info->link == link)
+ break;
+ }
+ if (j == pci_root_num)
+ continue; /* not found */
+
+ info = &pci_root_info[j];
+ update_res(info, start, end, IORESOURCE_IO, 0);
+ update_range(range, start, end);
+ }
+ /* add left over io port range to def node/link, [0, 0xffff] */
+ /* find the position */
+ for (j = 0; j < pci_root_num; j++) {
+ info = &pci_root_info[j];
+ if (info->node == def_node && info->link == def_link)
+ break;
+ }
+ if (j < pci_root_num) {
+ info = &pci_root_info[j];
+ for (i = 0; i < RANGE_NUM; i++) {
+ if (!range[i].end)
+ continue;
+
+ update_res(info, range[i].start, range[i].end,
+ IORESOURCE_IO, 1);
+ }
+ }
+
+ memset(range, 0, sizeof(range));
+ /* 0xfd00000000-0xffffffffff for HT */
+ /* 0xfc00000000-0xfcffffffff for Family 10h mmconfig*/
+ range[0].end = 0xfbffffffffULL;
+
+ /* need to take out [0, TOM) for RAM*/
+ address = MSR_K8_TOP_MEM1;
+ rdmsrl(address, val);
+ end = (val & 0xffffff8000000ULL);
+ printk(KERN_INFO "TOM: %016lx aka %ldM\n", end, end>>20);
+ if (end < (1ULL<<32))
+ update_range(range, 0, end - 1);
+
+ /* mmio resource */
+ for (i = 0; i < 8; i++) {
+ reg = read_pci_config(bus, slot, 1, 0x80 + (i << 3));
+ if (!(reg & 3))
+ continue;
+
+ start = reg & 0xffffff00; /* 39:16 on 31:8*/
+ start <<= 8;
+ reg = read_pci_config(bus, slot, 1, 0x84 + (i << 3));
+ node = reg & 0x07;
+ link = (reg >> 4) & 0x03;
+ end = (reg & 0xffffff00);
+ end <<= 8;
+ end |= 0xffff;
+
+ /* find the position */
+ for (j = 0; j < pci_root_num; j++) {
+ info = &pci_root_info[j];
+ if (info->node == node && info->link == link)
+ break;
+ }
+ if (j == pci_root_num)
+ continue; /* not found */
+
+ info = &pci_root_info[j];
+ update_res(info, start, end, IORESOURCE_MEM, 0);
+ update_range(range, start, end);
+ }
+
+ /* need to take out [4G, TOM2) for RAM*/
+ /* SYS_CFG */
+ address = MSR_K8_SYSCFG;
+ rdmsrl(address, val);
+ /* TOP_MEM2 is enabled? */
+ if (val & (1<<21)) {
+ /* TOP_MEM2 */
+ address = MSR_K8_TOP_MEM2;
+ rdmsrl(address, val);
+ end = (val & 0xffffff8000000ULL);
+ printk(KERN_INFO "TOM2: %016lx aka %ldM\n", end, end>>20);
+ update_range(range, 1ULL<<32, end - 1);
+ }
+
+ /*
+ * add left over mmio range to def node/link ?
+ * that is tricky, just record range in from start_min to 4G
+ */
+ for (j = 0; j < pci_root_num; j++) {
+ info = &pci_root_info[j];
+ if (info->node == def_node && info->link == def_link)
+ break;
+ }
+ if (j < pci_root_num) {
+ info = &pci_root_info[j];
+
+ for (i = 0; i < RANGE_NUM; i++) {
+ if (!range[i].end)
+ continue;
+
+ update_res(info, range[i].start, range[i].end,
+ IORESOURCE_MEM, 1);
+ }
+ }
+
+#ifdef CONFIG_NUMA
for (i = 0; i < BUS_NR; i++) {
node = mp_bus_to_node[i];
if (node >= 0)
printk(KERN_DEBUG "bus: %02x to node: %02x\n", i, node);
}
#endif
+
+ for (i = 0; i < pci_root_num; i++) {
+ int res_num;
+ int busnum;
+
+ info = &pci_root_info[i];
+ res_num = info->res_num;
+ busnum = info->bus_min;
+ printk(KERN_DEBUG "bus: [%02x,%02x] on node %x link %x\n",
+ info->bus_min, info->bus_max, info->node, info->link);
+ for (j = 0; j < res_num; j++) {
+ res = &info->res[j];
+ printk(KERN_DEBUG "bus: %02x index %x %s: [%llx, %llx]\n",
+ busnum, j,
+ (res->flags & IORESOURCE_IO)?"io port":"mmio",
+ res->start, res->end);
+ }
+ }
+
return 0;
}
-postcore_initcall(early_fill_mp_bus_to_node);
+postcore_initcall(early_fill_mp_bus_info);