mtd: nand: Create a NAND reset function
When NAND devices are resetted some initialization may have to be done,
like for example they have to be configured for the timing mode that
shall be used. To get a common place where this initialization can be
implemented create a nand_reset() function. This currently only issues
a NAND_CMD_RESET to the NAND device. The places issuing this command
manually are replaced with a call to nand_reset().
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
diff --git a/drivers/mtd/nand/nand_base.c b/drivers/mtd/nand/nand_base.c
index 108adef..1a63105 100644
--- a/drivers/mtd/nand/nand_base.c
+++ b/drivers/mtd/nand/nand_base.c
@@ -948,6 +948,21 @@
}
/**
+ * nand_reset - Reset and initialize a NAND device
+ * @chip: The NAND chip
+ *
+ * Returns 0 for success or negative error code otherwise
+ */
+int nand_reset(struct nand_chip *chip)
+{
+ struct mtd_info *mtd = nand_to_mtd(chip);
+
+ chip->cmdfunc(mtd, NAND_CMD_RESET, -1, -1);
+
+ return 0;
+}
+
+/**
* __nand_unlock - [REPLACEABLE] unlocks specified locked blocks
* @mtd: mtd info
* @ofs: offset to start unlock from
@@ -1025,7 +1040,7 @@
* some operation can also clear the bit 7 of status register
* eg. erase/program a locked block
*/
- chip->cmdfunc(mtd, NAND_CMD_RESET, -1, -1);
+ nand_reset(chip);
/* Check, if it is write protected */
if (nand_check_wp(mtd)) {
@@ -1084,7 +1099,7 @@
* some operation can also clear the bit 7 of status register
* eg. erase/program a locked block
*/
- chip->cmdfunc(mtd, NAND_CMD_RESET, -1, -1);
+ nand_reset(chip);
/* Check, if it is write protected */
if (nand_check_wp(mtd)) {
@@ -2782,7 +2797,7 @@
* if we don't do this. I have no clue why, but I seem to have 'fixed'
* it in the doc2000 driver in August 1999. dwmw2.
*/
- chip->cmdfunc(mtd, NAND_CMD_RESET, -1, -1);
+ nand_reset(chip);
/* Check, if it is write protected */
if (nand_check_wp(mtd)) {
@@ -3822,7 +3837,7 @@
* Reset the chip, required by some chips (e.g. Micron MT29FxGxxxxx)
* after power-up.
*/
- chip->cmdfunc(mtd, NAND_CMD_RESET, -1, -1);
+ nand_reset(chip);
/* Send the command for reading device ID */
chip->cmdfunc(mtd, NAND_CMD_READID, 0x00, -1);
@@ -4163,7 +4178,7 @@
for (i = 1; i < maxchips; i++) {
chip->select_chip(mtd, i);
/* See comment in nand_get_flash_type for reset */
- chip->cmdfunc(mtd, NAND_CMD_RESET, -1, -1);
+ nand_reset(chip);
/* Send the command for reading device ID */
chip->cmdfunc(mtd, NAND_CMD_READID, 0x00, -1);
/* Read manufacturer and device IDs */