net: bcmgenet: add support for ethtool flow control
This commit extends the supported ethtool operations to allow MAC
level flow control to be configured for the bcmgenet driver.
The ethtool utility can be used to change the configuration of
auto-negotiated symmetric and asymmetric modes as well as manually
configuring support for RX and TX Pause frames individually.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
diff --git a/drivers/net/ethernet/broadcom/genet/bcmgenet.c b/drivers/net/ethernet/broadcom/genet/bcmgenet.c
index 3427f9e..6a8234b 100644
--- a/drivers/net/ethernet/broadcom/genet/bcmgenet.c
+++ b/drivers/net/ethernet/broadcom/genet/bcmgenet.c
@@ -935,6 +935,48 @@ static int bcmgenet_set_coalesce(struct net_device *dev,
return 0;
}
+static void bcmgenet_get_pauseparam(struct net_device *dev,
+ struct ethtool_pauseparam *epause)
+{
+ struct bcmgenet_priv *priv;
+ u32 umac_cmd;
+
+ priv = netdev_priv(dev);
+
+ epause->autoneg = priv->autoneg_pause;
+
+ if (netif_carrier_ok(dev)) {
+ /* report active state when link is up */
+ umac_cmd = bcmgenet_umac_readl(priv, UMAC_CMD);
+ epause->tx_pause = !(umac_cmd & CMD_TX_PAUSE_IGNORE);
+ epause->rx_pause = !(umac_cmd & CMD_RX_PAUSE_IGNORE);
+ } else {
+ /* otherwise report stored settings */
+ epause->tx_pause = priv->tx_pause;
+ epause->rx_pause = priv->rx_pause;
+ }
+}
+
+static int bcmgenet_set_pauseparam(struct net_device *dev,
+ struct ethtool_pauseparam *epause)
+{
+ struct bcmgenet_priv *priv = netdev_priv(dev);
+
+ if (!dev->phydev)
+ return -ENODEV;
+
+ if (!phy_validate_pause(dev->phydev, epause))
+ return -EINVAL;
+
+ priv->autoneg_pause = !!epause->autoneg;
+ priv->tx_pause = !!epause->tx_pause;
+ priv->rx_pause = !!epause->rx_pause;
+
+ bcmgenet_phy_pause_set(dev, priv->rx_pause, priv->tx_pause);
+
+ return 0;
+}
+
/* standard ethtool support functions. */
enum bcmgenet_stat_type {
BCMGENET_STAT_NETDEV = -1,
@@ -1587,6 +1629,8 @@ static const struct ethtool_ops bcmgenet_ethtool_ops = {
.get_ts_info = ethtool_op_get_ts_info,
.get_rxnfc = bcmgenet_get_rxnfc,
.set_rxnfc = bcmgenet_set_rxnfc,
+ .get_pauseparam = bcmgenet_get_pauseparam,
+ .set_pauseparam = bcmgenet_set_pauseparam,
};
/* Power down the unimac, based on mode. */
@@ -3364,6 +3408,8 @@ static int bcmgenet_open(struct net_device *dev)
goto err_irq1;
}
+ bcmgenet_phy_pause_set(dev, priv->rx_pause, priv->tx_pause);
+
bcmgenet_netif_start(dev);
netif_tx_start_all_queues(dev);
@@ -3945,6 +3991,11 @@ static int bcmgenet_probe(struct platform_device *pdev)
spin_lock_init(&priv->lock);
+ /* Set default pause parameters */
+ priv->autoneg_pause = 1;
+ priv->tx_pause = 1;
+ priv->rx_pause = 1;
+
SET_NETDEV_DEV(dev, &pdev->dev);
dev_set_drvdata(&pdev->dev, dev);
dev->watchdog_timeo = 2 * HZ;