drm/i915: State readout and cross-checking for ddi_pll_sel
To make things a bit more manageable extract a new function for
reading out common ddi port state. This means a bit of duplication
between encoders and the core since both look at the same registers,
but doesn't seem worth to make a fuzz about.
We can also remove the state readout code in intel_ddi_setup_hw_pll_state.
That code is only called from the hardware take over and not the cross
check code, and only after the crtc state is reconstructed. So we can
rely on an accurate value of crtc->config.ddi_pll_sel already.
Compared to the old code also trust the hw state more and don't
special-case port A - we want to cross-check the actual-state, not
bake in our own assumptions about how this is supposed to all be
linked up.
v2: Make use of the read-out ddi_pll_sel in intel_ddi_clock_get.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
[imre: rebased on patchset version w/o pch/crt/fdi refactoring]
Signed-off-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
diff --git a/drivers/gpu/drm/i915/intel_ddi.c b/drivers/gpu/drm/i915/intel_ddi.c
index c96bc3b..1b4748b 100644
--- a/drivers/gpu/drm/i915/intel_ddi.c
+++ b/drivers/gpu/drm/i915/intel_ddi.c
@@ -612,11 +612,10 @@
struct intel_crtc_config *pipe_config)
{
struct drm_i915_private *dev_priv = encoder->base.dev->dev_private;
- enum port port = intel_ddi_get_encoder_port(encoder);
int link_clock = 0;
u32 val, pll;
- val = I915_READ(PORT_CLK_SEL(port));
+ val = pipe_config->ddi_pll_sel;
switch (val & PORT_CLK_SEL_MASK) {
case PORT_CLK_SEL_LCPLL_810:
link_clock = 81000;
@@ -1113,40 +1112,6 @@
return false;
}
-static uint32_t intel_ddi_get_crtc_pll(struct drm_i915_private *dev_priv,
- enum pipe pipe)
-{
- uint32_t temp, ret;
- enum port port = I915_MAX_PORTS;
- enum transcoder cpu_transcoder = intel_pipe_to_cpu_transcoder(dev_priv,
- pipe);
- int i;
-
- if (cpu_transcoder == TRANSCODER_EDP) {
- port = PORT_A;
- } else {
- temp = I915_READ(TRANS_DDI_FUNC_CTL(cpu_transcoder));
- temp &= TRANS_DDI_PORT_MASK;
-
- for (i = PORT_B; i <= PORT_E; i++)
- if (temp == TRANS_DDI_SELECT_PORT(i))
- port = i;
- }
-
- if (port == I915_MAX_PORTS) {
- WARN(1, "Pipe %c enabled on an unknown port\n",
- pipe_name(pipe));
- ret = PORT_CLK_SEL_NONE;
- } else {
- ret = I915_READ(PORT_CLK_SEL(port));
- DRM_DEBUG_KMS("Pipe %c connected to port %c using clock "
- "0x%08x\n", pipe_name(pipe), port_name(port),
- ret);
- }
-
- return ret;
-}
-
void intel_ddi_setup_hw_pll_state(struct drm_device *dev)
{
struct drm_i915_private *dev_priv = dev->dev_private;
@@ -1165,9 +1130,6 @@
continue;
}
- intel_crtc->config.ddi_pll_sel = intel_ddi_get_crtc_pll(dev_priv,
- pipe);
-
switch (intel_crtc->config.ddi_pll_sel) {
case PORT_CLK_SEL_WRPLL1:
dev_priv->ddi_plls.wrpll1_refcount++;