drm/i915: Restrict qgv points which don't have enough bandwidth.
According to BSpec 53998, we should try to
restrict qgv points, which can't provide
enough bandwidth for desired display configuration.
Currently we are just comparing against all of
those and take minimum(worst case).
v2: Fixed wrong PCode reply mask, removed hardcoded
values.
v3: Forbid simultaneous legacy SAGV PCode requests and
restricting qgv points. Put the actual restriction
to commit function, added serialization(thanks to Ville)
to prevent commit being applied out of order in case of
nonblocking and/or nomodeset commits.
v4:
- Minor code refactoring, fixed few typos(thanks to James Ausmus)
- Change the naming of qgv point
masking/unmasking functions(James Ausmus).
- Simplify the masking/unmasking operation itself,
as we don't need to mask only single point per request(James Ausmus)
- Reject and stick to highest bandwidth point if SAGV
can't be enabled(BSpec)
v5:
- Add new mailbox reply codes, which seems to happen during boot
time for TGL and indicate that QGV setting is not yet available.
v6:
- Increase number of supported QGV points to be in sync with BSpec.
v7: - Rebased and resolved conflict to fix build failure.
- Fix NUM_QGV_POINTS to 8 and moved that to header file(James Ausmus)
v8: - Don't report an error if we can't restrict qgv points, as SAGV
can be disabled by BIOS, which is completely legal. So don't
make CI panic. Instead if we detect that there is only 1 QGV
point accessible just analyze if we can fit the required bandwidth
requirements, but no need in restricting.
v9: - Fix wrong QGV transition if we have 0 planes and no SAGV
simultaneously.
v10: - Fix CDCLK corruption, because of global state getting serialized
without modeset, which caused copying of non-calculated cdclk
to be copied to dev_priv(thanks to Ville for the hint).
v11: - Remove unneeded headers and spaces(Matthew Roper)
- Remove unneeded intel_qgv_info qi struct from bw check and zero
out the needed one(Matthew Roper)
- Changed QGV error message to have more clear meaning(Matthew Roper)
- Use state->modeset_set instead of any_ms(Matthew Roper)
- Moved NUM_SAGV_POINTS from i915_reg.h to i915_drv.h where it's used
- Keep using crtc_state->hw.active instead of .enable(Matthew Roper)
- Moved unrelated changes to other patch(using latency as parameter
for plane wm calculation, moved to SAGV refactoring patch)
v12: - Fix rebase conflict with own temporary SAGV/QGV fix.
- Remove unnecessary mask being zero check when unmasking
qgv points as this is completely legal(Matt Roper)
- Check if we are setting the same mask as already being set
in hardware to prevent error from PCode.
- Fix error message when restricting/unrestricting qgv points
to "mask/unmask" which sounds more accurate(Matt Roper)
- Move sagv status setting to icl_get_bw_info from atomic check
as this should be calculated only once.(Matt Roper)
- Edited comments for the case when we can't enable SAGV and
use only 1 QGV point with highest bandwidth to be more
understandable.(Matt Roper)
v13: - Moved max_data_rate in bw check to closer scope(Ville Syrjälä)
- Changed comment for zero new_mask in qgv points masking function
to better reflect reality(Ville Syrjälä)
- Simplified bit mask operation in qgv points masking function
(Ville Syrjälä)
- Moved intel_qgv_points_mask closer to gen11 SAGV disabling,
however this still can't be under modeset condition(Ville Syrjälä)
- Packed qgv_points_mask as u8 and moved closer to pipe_sagv_mask
(Ville Syrjälä)
- Extracted PCode changes to separate patch.(Ville Syrjälä)
- Now treat num_planes 0 same as 1 to avoid confusion and
returning max_bw as 0, which would prevent choosing QGV
point having max bandwidth in case if SAGV is not allowed,
as per BSpec(Ville Syrjälä)
- Do the actual qgv_points_mask swap in the same place as
all other global state parts like cdclk are swapped.
In the next patch, this all will be moved to bw state as
global state, once new global state patch series from Ville
lands
v14: - Now using global state to serialize access to qgv points
- Added global state locking back, otherwise we seem to read
bw state in a wrong way.
v15: - Added TODO comment for near atomic global state locking in
bw code.
v16: - Fixed intel_atomic_bw_* functions to be intel_bw_* as discussed
with Jani Nikula.
- Take bw_state_changed flag into use.
v17: - Moved qgv point related manipulations next to SAGV code, as
those are semantically related(Ville Syrjälä)
- Renamed those into intel_sagv_(pre)|(post)_plane_update
(Ville Syrjälä)
v18: - Move sagv related calls from commit tail into
intel_sagv_(pre)|(post)_plane_update(Ville Syrjälä)
v19: - Use intel_atomic_get_bw_(old)|(new)_state which is intended
for commit tail stage.
v20: - Return max bandwidth for 0 planes(Ville)
- Constify old_bw_state in bw_atomic_check(Ville)
- Removed some debugs(Ville)
- Added data rate to debug print when no QGV points(Ville)
- Removed some comments(Ville)
v21, v22, v23: - Fixed rebase conflict
v24: - Changed PCode mask to use ICL_ prefix
v25: - Resolved rebase conflict
v26: - Removed redundant NULL checks(Ville)
- Removed redundant error prints(Ville)
v27: - Use device specific drm_err(Ville)
- Fixed parenthesis ident reported by checkpatch
Line over 100 warns to be fixed together with
existing code style.
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Cc: Ville Syrjälä <ville.syrjala@intel.com>
Cc: James Ausmus <james.ausmus@intel.com>
[vsyrjala: Drop duplicate intel_sagv_{pre,post}_plane_update() prototypes
and drop unused NUM_SAGV_POINTS define]
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200514074853.9508-3-stanislav.lisovskiy@intel.com
3 files changed