Linux-2.6.12-rc2
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
diff --git a/drivers/scsi/sata_sil.c b/drivers/scsi/sata_sil.c
new file mode 100644
index 0000000..f0489dc
--- /dev/null
+++ b/drivers/scsi/sata_sil.c
@@ -0,0 +1,494 @@
+/*
+ * sata_sil.c - Silicon Image SATA
+ *
+ * Maintained by: Jeff Garzik <jgarzik@pobox.com>
+ * Please ALWAYS copy linux-ide@vger.kernel.org
+ * on emails.
+ *
+ * Copyright 2003 Red Hat, Inc.
+ * Copyright 2003 Benjamin Herrenschmidt
+ *
+ * The contents of this file are subject to the Open
+ * Software License version 1.1 that can be found at
+ * http://www.opensource.org/licenses/osl-1.1.txt and is included herein
+ * by reference.
+ *
+ * Alternatively, the contents of this file may be used under the terms
+ * of the GNU General Public License version 2 (the "GPL") as distributed
+ * in the kernel source COPYING file, in which case the provisions of
+ * the GPL are applicable instead of the above. If you wish to allow
+ * the use of your version of this file only under the terms of the
+ * GPL and not to allow others to use your version of this file under
+ * the OSL, indicate your decision by deleting the provisions above and
+ * replace them with the notice and other provisions required by the GPL.
+ * If you do not delete the provisions above, a recipient may use your
+ * version of this file under either the OSL or the GPL.
+ *
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/init.h>
+#include <linux/blkdev.h>
+#include <linux/delay.h>
+#include <linux/interrupt.h>
+#include "scsi.h"
+#include <scsi/scsi_host.h>
+#include <linux/libata.h>
+
+#define DRV_NAME "sata_sil"
+#define DRV_VERSION "0.9"
+
+enum {
+ sil_3112 = 0,
+ sil_3114 = 1,
+
+ SIL_FIFO_R0 = 0x40,
+ SIL_FIFO_W0 = 0x41,
+ SIL_FIFO_R1 = 0x44,
+ SIL_FIFO_W1 = 0x45,
+ SIL_FIFO_R2 = 0x240,
+ SIL_FIFO_W2 = 0x241,
+ SIL_FIFO_R3 = 0x244,
+ SIL_FIFO_W3 = 0x245,
+
+ SIL_SYSCFG = 0x48,
+ SIL_MASK_IDE0_INT = (1 << 22),
+ SIL_MASK_IDE1_INT = (1 << 23),
+ SIL_MASK_IDE2_INT = (1 << 24),
+ SIL_MASK_IDE3_INT = (1 << 25),
+ SIL_MASK_2PORT = SIL_MASK_IDE0_INT | SIL_MASK_IDE1_INT,
+ SIL_MASK_4PORT = SIL_MASK_2PORT |
+ SIL_MASK_IDE2_INT | SIL_MASK_IDE3_INT,
+
+ SIL_IDE2_BMDMA = 0x200,
+
+ SIL_INTR_STEERING = (1 << 1),
+ SIL_QUIRK_MOD15WRITE = (1 << 0),
+ SIL_QUIRK_UDMA5MAX = (1 << 1),
+};
+
+static int sil_init_one (struct pci_dev *pdev, const struct pci_device_id *ent);
+static void sil_dev_config(struct ata_port *ap, struct ata_device *dev);
+static u32 sil_scr_read (struct ata_port *ap, unsigned int sc_reg);
+static void sil_scr_write (struct ata_port *ap, unsigned int sc_reg, u32 val);
+static void sil_post_set_mode (struct ata_port *ap);
+
+static struct pci_device_id sil_pci_tbl[] = {
+ { 0x1095, 0x3112, PCI_ANY_ID, PCI_ANY_ID, 0, 0, sil_3112 },
+ { 0x1095, 0x0240, PCI_ANY_ID, PCI_ANY_ID, 0, 0, sil_3112 },
+ { 0x1095, 0x3512, PCI_ANY_ID, PCI_ANY_ID, 0, 0, sil_3112 },
+ { 0x1095, 0x3114, PCI_ANY_ID, PCI_ANY_ID, 0, 0, sil_3114 },
+ { 0x1002, 0x436e, PCI_ANY_ID, PCI_ANY_ID, 0, 0, sil_3112 },
+ { 0x1002, 0x4379, PCI_ANY_ID, PCI_ANY_ID, 0, 0, sil_3112 },
+ { } /* terminate list */
+};
+
+
+/* TODO firmware versions should be added - eric */
+static const struct sil_drivelist {
+ const char * product;
+ unsigned int quirk;
+} sil_blacklist [] = {
+ { "ST320012AS", SIL_QUIRK_MOD15WRITE },
+ { "ST330013AS", SIL_QUIRK_MOD15WRITE },
+ { "ST340017AS", SIL_QUIRK_MOD15WRITE },
+ { "ST360015AS", SIL_QUIRK_MOD15WRITE },
+ { "ST380013AS", SIL_QUIRK_MOD15WRITE },
+ { "ST380023AS", SIL_QUIRK_MOD15WRITE },
+ { "ST3120023AS", SIL_QUIRK_MOD15WRITE },
+ { "ST3160023AS", SIL_QUIRK_MOD15WRITE },
+ { "ST3120026AS", SIL_QUIRK_MOD15WRITE },
+ { "ST3200822AS", SIL_QUIRK_MOD15WRITE },
+ { "ST340014ASL", SIL_QUIRK_MOD15WRITE },
+ { "ST360014ASL", SIL_QUIRK_MOD15WRITE },
+ { "ST380011ASL", SIL_QUIRK_MOD15WRITE },
+ { "ST3120022ASL", SIL_QUIRK_MOD15WRITE },
+ { "ST3160021ASL", SIL_QUIRK_MOD15WRITE },
+ { "Maxtor 4D060H3", SIL_QUIRK_UDMA5MAX },
+ { }
+};
+
+static struct pci_driver sil_pci_driver = {
+ .name = DRV_NAME,
+ .id_table = sil_pci_tbl,
+ .probe = sil_init_one,
+ .remove = ata_pci_remove_one,
+};
+
+static Scsi_Host_Template sil_sht = {
+ .module = THIS_MODULE,
+ .name = DRV_NAME,
+ .ioctl = ata_scsi_ioctl,
+ .queuecommand = ata_scsi_queuecmd,
+ .eh_strategy_handler = ata_scsi_error,
+ .can_queue = ATA_DEF_QUEUE,
+ .this_id = ATA_SHT_THIS_ID,
+ .sg_tablesize = LIBATA_MAX_PRD,
+ .max_sectors = ATA_MAX_SECTORS,
+ .cmd_per_lun = ATA_SHT_CMD_PER_LUN,
+ .emulated = ATA_SHT_EMULATED,
+ .use_clustering = ATA_SHT_USE_CLUSTERING,
+ .proc_name = DRV_NAME,
+ .dma_boundary = ATA_DMA_BOUNDARY,
+ .slave_configure = ata_scsi_slave_config,
+ .bios_param = ata_std_bios_param,
+ .ordered_flush = 1,
+};
+
+static struct ata_port_operations sil_ops = {
+ .port_disable = ata_port_disable,
+ .dev_config = sil_dev_config,
+ .tf_load = ata_tf_load,
+ .tf_read = ata_tf_read,
+ .check_status = ata_check_status,
+ .exec_command = ata_exec_command,
+ .dev_select = ata_std_dev_select,
+ .phy_reset = sata_phy_reset,
+ .post_set_mode = sil_post_set_mode,
+ .bmdma_setup = ata_bmdma_setup,
+ .bmdma_start = ata_bmdma_start,
+ .bmdma_stop = ata_bmdma_stop,
+ .bmdma_status = ata_bmdma_status,
+ .qc_prep = ata_qc_prep,
+ .qc_issue = ata_qc_issue_prot,
+ .eng_timeout = ata_eng_timeout,
+ .irq_handler = ata_interrupt,
+ .irq_clear = ata_bmdma_irq_clear,
+ .scr_read = sil_scr_read,
+ .scr_write = sil_scr_write,
+ .port_start = ata_port_start,
+ .port_stop = ata_port_stop,
+};
+
+static struct ata_port_info sil_port_info[] = {
+ /* sil_3112 */
+ {
+ .sht = &sil_sht,
+ .host_flags = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY |
+ ATA_FLAG_SRST | ATA_FLAG_MMIO,
+ .pio_mask = 0x1f, /* pio0-4 */
+ .mwdma_mask = 0x07, /* mwdma0-2 */
+ .udma_mask = 0x3f, /* udma0-5 */
+ .port_ops = &sil_ops,
+ }, /* sil_3114 */
+ {
+ .sht = &sil_sht,
+ .host_flags = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY |
+ ATA_FLAG_SRST | ATA_FLAG_MMIO,
+ .pio_mask = 0x1f, /* pio0-4 */
+ .mwdma_mask = 0x07, /* mwdma0-2 */
+ .udma_mask = 0x3f, /* udma0-5 */
+ .port_ops = &sil_ops,
+ },
+};
+
+/* per-port register offsets */
+/* TODO: we can probably calculate rather than use a table */
+static const struct {
+ unsigned long tf; /* ATA taskfile register block */
+ unsigned long ctl; /* ATA control/altstatus register block */
+ unsigned long bmdma; /* DMA register block */
+ unsigned long scr; /* SATA control register block */
+ unsigned long sien; /* SATA Interrupt Enable register */
+ unsigned long xfer_mode;/* data transfer mode register */
+} sil_port[] = {
+ /* port 0 ... */
+ { 0x80, 0x8A, 0x00, 0x100, 0x148, 0xb4 },
+ { 0xC0, 0xCA, 0x08, 0x180, 0x1c8, 0xf4 },
+ { 0x280, 0x28A, 0x200, 0x300, 0x348, 0x2b4 },
+ { 0x2C0, 0x2CA, 0x208, 0x380, 0x3c8, 0x2f4 },
+ /* ... port 3 */
+};
+
+MODULE_AUTHOR("Jeff Garzik");
+MODULE_DESCRIPTION("low-level driver for Silicon Image SATA controller");
+MODULE_LICENSE("GPL");
+MODULE_DEVICE_TABLE(pci, sil_pci_tbl);
+MODULE_VERSION(DRV_VERSION);
+
+static unsigned char sil_get_device_cache_line(struct pci_dev *pdev)
+{
+ u8 cache_line = 0;
+ pci_read_config_byte(pdev, PCI_CACHE_LINE_SIZE, &cache_line);
+ return cache_line;
+}
+
+static void sil_post_set_mode (struct ata_port *ap)
+{
+ struct ata_host_set *host_set = ap->host_set;
+ struct ata_device *dev;
+ void *addr = host_set->mmio_base + sil_port[ap->port_no].xfer_mode;
+ u32 tmp, dev_mode[2];
+ unsigned int i;
+
+ for (i = 0; i < 2; i++) {
+ dev = &ap->device[i];
+ if (!ata_dev_present(dev))
+ dev_mode[i] = 0; /* PIO0/1/2 */
+ else if (dev->flags & ATA_DFLAG_PIO)
+ dev_mode[i] = 1; /* PIO3/4 */
+ else
+ dev_mode[i] = 3; /* UDMA */
+ /* value 2 indicates MDMA */
+ }
+
+ tmp = readl(addr);
+ tmp &= ~((1<<5) | (1<<4) | (1<<1) | (1<<0));
+ tmp |= dev_mode[0];
+ tmp |= (dev_mode[1] << 4);
+ writel(tmp, addr);
+ readl(addr); /* flush */
+}
+
+static inline unsigned long sil_scr_addr(struct ata_port *ap, unsigned int sc_reg)
+{
+ unsigned long offset = ap->ioaddr.scr_addr;
+
+ switch (sc_reg) {
+ case SCR_STATUS:
+ return offset + 4;
+ case SCR_ERROR:
+ return offset + 8;
+ case SCR_CONTROL:
+ return offset;
+ default:
+ /* do nothing */
+ break;
+ }
+
+ return 0;
+}
+
+static u32 sil_scr_read (struct ata_port *ap, unsigned int sc_reg)
+{
+ void *mmio = (void *) sil_scr_addr(ap, sc_reg);
+ if (mmio)
+ return readl(mmio);
+ return 0xffffffffU;
+}
+
+static void sil_scr_write (struct ata_port *ap, unsigned int sc_reg, u32 val)
+{
+ void *mmio = (void *) sil_scr_addr(ap, sc_reg);
+ if (mmio)
+ writel(val, mmio);
+}
+
+/**
+ * sil_dev_config - Apply device/host-specific errata fixups
+ * @ap: Port containing device to be examined
+ * @dev: Device to be examined
+ *
+ * After the IDENTIFY [PACKET] DEVICE step is complete, and a
+ * device is known to be present, this function is called.
+ * We apply two errata fixups which are specific to Silicon Image,
+ * a Seagate and a Maxtor fixup.
+ *
+ * For certain Seagate devices, we must limit the maximum sectors
+ * to under 8K.
+ *
+ * For certain Maxtor devices, we must not program the drive
+ * beyond udma5.
+ *
+ * Both fixups are unfairly pessimistic. As soon as I get more
+ * information on these errata, I will create a more exhaustive
+ * list, and apply the fixups to only the specific
+ * devices/hosts/firmwares that need it.
+ *
+ * 20040111 - Seagate drives affected by the Mod15Write bug are blacklisted
+ * The Maxtor quirk is in the blacklist, but I'm keeping the original
+ * pessimistic fix for the following reasons...
+ * - There seems to be less info on it, only one device gleaned off the
+ * Windows driver, maybe only one is affected. More info would be greatly
+ * appreciated.
+ * - But then again UDMA5 is hardly anything to complain about
+ */
+static void sil_dev_config(struct ata_port *ap, struct ata_device *dev)
+{
+ unsigned int n, quirks = 0;
+ unsigned char model_num[40];
+ const char *s;
+ unsigned int len;
+
+ ata_dev_id_string(dev->id, model_num, ATA_ID_PROD_OFS,
+ sizeof(model_num));
+ s = &model_num[0];
+ len = strnlen(s, sizeof(model_num));
+
+ /* ATAPI specifies that empty space is blank-filled; remove blanks */
+ while ((len > 0) && (s[len - 1] == ' '))
+ len--;
+
+ for (n = 0; sil_blacklist[n].product; n++)
+ if (!memcmp(sil_blacklist[n].product, s,
+ strlen(sil_blacklist[n].product))) {
+ quirks = sil_blacklist[n].quirk;
+ break;
+ }
+
+ /* limit requests to 15 sectors */
+ if (quirks & SIL_QUIRK_MOD15WRITE) {
+ printk(KERN_INFO "ata%u(%u): applying Seagate errata fix\n",
+ ap->id, dev->devno);
+ ap->host->max_sectors = 15;
+ ap->host->hostt->max_sectors = 15;
+ dev->flags |= ATA_DFLAG_LOCK_SECTORS;
+ return;
+ }
+
+ /* limit to udma5 */
+ if (quirks & SIL_QUIRK_UDMA5MAX) {
+ printk(KERN_INFO "ata%u(%u): applying Maxtor errata fix %s\n",
+ ap->id, dev->devno, s);
+ ap->udma_mask &= ATA_UDMA5;
+ return;
+ }
+}
+
+static int sil_init_one (struct pci_dev *pdev, const struct pci_device_id *ent)
+{
+ static int printed_version;
+ struct ata_probe_ent *probe_ent = NULL;
+ unsigned long base;
+ void *mmio_base;
+ int rc;
+ unsigned int i;
+ int pci_dev_busy = 0;
+ u32 tmp, irq_mask;
+ u8 cls;
+
+ if (!printed_version++)
+ printk(KERN_DEBUG DRV_NAME " version " DRV_VERSION "\n");
+
+ /*
+ * If this driver happens to only be useful on Apple's K2, then
+ * we should check that here as it has a normal Serverworks ID
+ */
+ rc = pci_enable_device(pdev);
+ if (rc)
+ return rc;
+
+ rc = pci_request_regions(pdev, DRV_NAME);
+ if (rc) {
+ pci_dev_busy = 1;
+ goto err_out;
+ }
+
+ rc = pci_set_dma_mask(pdev, ATA_DMA_MASK);
+ if (rc)
+ goto err_out_regions;
+ rc = pci_set_consistent_dma_mask(pdev, ATA_DMA_MASK);
+ if (rc)
+ goto err_out_regions;
+
+ probe_ent = kmalloc(sizeof(*probe_ent), GFP_KERNEL);
+ if (probe_ent == NULL) {
+ rc = -ENOMEM;
+ goto err_out_regions;
+ }
+
+ memset(probe_ent, 0, sizeof(*probe_ent));
+ INIT_LIST_HEAD(&probe_ent->node);
+ probe_ent->dev = pci_dev_to_dev(pdev);
+ probe_ent->port_ops = sil_port_info[ent->driver_data].port_ops;
+ probe_ent->sht = sil_port_info[ent->driver_data].sht;
+ probe_ent->n_ports = (ent->driver_data == sil_3114) ? 4 : 2;
+ probe_ent->pio_mask = sil_port_info[ent->driver_data].pio_mask;
+ probe_ent->mwdma_mask = sil_port_info[ent->driver_data].mwdma_mask;
+ probe_ent->udma_mask = sil_port_info[ent->driver_data].udma_mask;
+ probe_ent->irq = pdev->irq;
+ probe_ent->irq_flags = SA_SHIRQ;
+ probe_ent->host_flags = sil_port_info[ent->driver_data].host_flags;
+
+ mmio_base = ioremap(pci_resource_start(pdev, 5),
+ pci_resource_len(pdev, 5));
+ if (mmio_base == NULL) {
+ rc = -ENOMEM;
+ goto err_out_free_ent;
+ }
+
+ probe_ent->mmio_base = mmio_base;
+
+ base = (unsigned long) mmio_base;
+
+ for (i = 0; i < probe_ent->n_ports; i++) {
+ probe_ent->port[i].cmd_addr = base + sil_port[i].tf;
+ probe_ent->port[i].altstatus_addr =
+ probe_ent->port[i].ctl_addr = base + sil_port[i].ctl;
+ probe_ent->port[i].bmdma_addr = base + sil_port[i].bmdma;
+ probe_ent->port[i].scr_addr = base + sil_port[i].scr;
+ ata_std_ports(&probe_ent->port[i]);
+ }
+
+ /* Initialize FIFO PCI bus arbitration */
+ cls = sil_get_device_cache_line(pdev);
+ if (cls) {
+ cls >>= 3;
+ cls++; /* cls = (line_size/8)+1 */
+ writeb(cls, mmio_base + SIL_FIFO_R0);
+ writeb(cls, mmio_base + SIL_FIFO_W0);
+ writeb(cls, mmio_base + SIL_FIFO_R1);
+ writeb(cls, mmio_base + SIL_FIFO_W2);
+ } else
+ printk(KERN_WARNING DRV_NAME "(%s): cache line size not set. Driver may not function\n",
+ pci_name(pdev));
+
+ if (ent->driver_data == sil_3114) {
+ irq_mask = SIL_MASK_4PORT;
+
+ /* flip the magic "make 4 ports work" bit */
+ tmp = readl(mmio_base + SIL_IDE2_BMDMA);
+ if ((tmp & SIL_INTR_STEERING) == 0)
+ writel(tmp | SIL_INTR_STEERING,
+ mmio_base + SIL_IDE2_BMDMA);
+
+ } else {
+ irq_mask = SIL_MASK_2PORT;
+ }
+
+ /* make sure IDE0/1/2/3 interrupts are not masked */
+ tmp = readl(mmio_base + SIL_SYSCFG);
+ if (tmp & irq_mask) {
+ tmp &= ~irq_mask;
+ writel(tmp, mmio_base + SIL_SYSCFG);
+ readl(mmio_base + SIL_SYSCFG); /* flush */
+ }
+
+ /* mask all SATA phy-related interrupts */
+ /* TODO: unmask bit 6 (SError N bit) for hotplug */
+ for (i = 0; i < probe_ent->n_ports; i++)
+ writel(0, mmio_base + sil_port[i].sien);
+
+ pci_set_master(pdev);
+
+ /* FIXME: check ata_device_add return value */
+ ata_device_add(probe_ent);
+ kfree(probe_ent);
+
+ return 0;
+
+err_out_free_ent:
+ kfree(probe_ent);
+err_out_regions:
+ pci_release_regions(pdev);
+err_out:
+ if (!pci_dev_busy)
+ pci_disable_device(pdev);
+ return rc;
+}
+
+static int __init sil_init(void)
+{
+ return pci_module_init(&sil_pci_driver);
+}
+
+static void __exit sil_exit(void)
+{
+ pci_unregister_driver(&sil_pci_driver);
+}
+
+
+module_init(sil_init);
+module_exit(sil_exit);