mac80211: remove RX_FLAG_RADIOTAP
While there may be a case for a driver adding its
own bits of radiotap information, none currently
does. Also, drivers would have to copy the code
to generate the radiotap bits that now mac80211
generates. If some driver in the future needs to
add some driver-specific information I'd expect
that to be in a radiotap vendor namespace and we
can add a different way of passing such data up
and having mac80211 include it.
Additionally, rename IEEE80211_CONF_RADIOTAP to
IEEE80211_CONF_MONITOR since it's still used by
b43(legacy) to obtain per-frame timestamps.
The purpose of this patch is to simplify the RX
code in mac80211 to make it easier to add paged
skb support.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
diff --git a/include/net/mac80211.h b/include/net/mac80211.h
index c42c4a8..2c9d3c7 100644
--- a/include/net/mac80211.h
+++ b/include/net/mac80211.h
@@ -494,7 +494,6 @@
* @RX_FLAG_MMIC_ERROR: Michael MIC error was reported on this frame.
* Use together with %RX_FLAG_MMIC_STRIPPED.
* @RX_FLAG_DECRYPTED: This frame was decrypted in hardware.
- * @RX_FLAG_RADIOTAP: This frame starts with a radiotap header.
* @RX_FLAG_MMIC_STRIPPED: the Michael MIC is stripped off this frame,
* verification has been done by the hardware.
* @RX_FLAG_IV_STRIPPED: The IV/ICV are stripped from this frame.
@@ -515,7 +514,6 @@
enum mac80211_rx_flags {
RX_FLAG_MMIC_ERROR = 1<<0,
RX_FLAG_DECRYPTED = 1<<1,
- RX_FLAG_RADIOTAP = 1<<2,
RX_FLAG_MMIC_STRIPPED = 1<<3,
RX_FLAG_IV_STRIPPED = 1<<4,
RX_FLAG_FAILED_FCS_CRC = 1<<5,
@@ -565,7 +563,9 @@
*
* Flags to define PHY configuration options
*
- * @IEEE80211_CONF_RADIOTAP: add radiotap header at receive time (if supported)
+ * @IEEE80211_CONF_MONITOR: there's a monitor interface present -- use this
+ * to determine for example whether to calculate timestamps for packets
+ * or not, do not use instead of filter flags!
* @IEEE80211_CONF_PS: Enable 802.11 power save mode (managed mode only)
* @IEEE80211_CONF_IDLE: The device is running, but idle; if the flag is set
* the driver should be prepared to handle configuration requests but
@@ -574,7 +574,7 @@
* it can also be unset in that case when monitor interfaces are active.
*/
enum ieee80211_conf_flags {
- IEEE80211_CONF_RADIOTAP = (1<<0),
+ IEEE80211_CONF_MONITOR = (1<<0),
IEEE80211_CONF_PS = (1<<1),
IEEE80211_CONF_IDLE = (1<<2),
};
@@ -584,7 +584,7 @@
* enum ieee80211_conf_changed - denotes which configuration changed
*
* @IEEE80211_CONF_CHANGE_LISTEN_INTERVAL: the listen interval changed
- * @IEEE80211_CONF_CHANGE_RADIOTAP: the radiotap flag changed
+ * @IEEE80211_CONF_CHANGE_MONITOR: the monitor flag changed
* @IEEE80211_CONF_CHANGE_PS: the PS flag or dynamic PS timeout changed
* @IEEE80211_CONF_CHANGE_POWER: the TX power changed
* @IEEE80211_CONF_CHANGE_CHANNEL: the channel/channel_type changed
@@ -593,7 +593,7 @@
*/
enum ieee80211_conf_changed {
IEEE80211_CONF_CHANGE_LISTEN_INTERVAL = BIT(2),
- IEEE80211_CONF_CHANGE_RADIOTAP = BIT(3),
+ IEEE80211_CONF_CHANGE_MONITOR = BIT(3),
IEEE80211_CONF_CHANGE_PS = BIT(4),
IEEE80211_CONF_CHANGE_POWER = BIT(5),
IEEE80211_CONF_CHANGE_CHANNEL = BIT(6),
@@ -1661,8 +1661,7 @@
* ieee80211_rx - receive frame
*
* Use this function to hand received frames to mac80211. The receive
- * buffer in @skb must start with an IEEE 802.11 header or a radiotap
- * header if %RX_FLAG_RADIOTAP is set in the @status flags.
+ * buffer in @skb must start with an IEEE 802.11 header.
*
* This function may not be called in IRQ context. Calls to this function
* for a single hardware must be synchronized against each other. Calls to