ssb: Implement the remaining rev.8 SPROM vars needed for LP-PHY
Also add a "SPEX32" macro for extracting 32-bit SPROM variables.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
diff --git a/include/linux/ssb/ssb.h b/include/linux/ssb/ssb.h
index 5ae8fa2..17ffc1f 100644
--- a/include/linux/ssb/ssb.h
+++ b/include/linux/ssb/ssb.h
@@ -27,24 +27,54 @@
u8 et1mdcport; /* MDIO for enet1 */
u8 board_rev; /* Board revision number from SPROM. */
u8 country_code; /* Country Code */
- u8 ant_available_a; /* A-PHY antenna available bits (up to 4) */
- u8 ant_available_bg; /* B/G-PHY antenna available bits (up to 4) */
+ u8 ant_available_a; /* 2GHz antenna available bits (up to 4) */
+ u8 ant_available_bg; /* 5GHz antenna available bits (up to 4) */
u16 pa0b0;
u16 pa0b1;
u16 pa0b2;
u16 pa1b0;
u16 pa1b1;
u16 pa1b2;
+ u16 pa1lob0;
+ u16 pa1lob1;
+ u16 pa1lob2;
+ u16 pa1hib0;
+ u16 pa1hib1;
+ u16 pa1hib2;
u8 gpio0; /* GPIO pin 0 */
u8 gpio1; /* GPIO pin 1 */
u8 gpio2; /* GPIO pin 2 */
u8 gpio3; /* GPIO pin 3 */
- u16 maxpwr_a; /* A-PHY Amplifier Max Power (in dBm Q5.2) */
- u16 maxpwr_bg; /* B/G-PHY Amplifier Max Power (in dBm Q5.2) */
+ u16 maxpwr_bg; /* 2.4GHz Amplifier Max Power (in dBm Q5.2) */
+ u16 maxpwr_al; /* 5.2GHz Amplifier Max Power (in dBm Q5.2) */
+ u16 maxpwr_a; /* 5.3GHz Amplifier Max Power (in dBm Q5.2) */
+ u16 maxpwr_ah; /* 5.8GHz Amplifier Max Power (in dBm Q5.2) */
u8 itssi_a; /* Idle TSSI Target for A-PHY */
u8 itssi_bg; /* Idle TSSI Target for B/G-PHY */
- u16 boardflags_lo; /* Boardflags (low 16 bits) */
- u16 boardflags_hi; /* Boardflags (high 16 bits) */
+ u8 tri2g; /* 2.4GHz TX isolation */
+ u8 tri5gl; /* 5.2GHz TX isolation */
+ u8 tri5g; /* 5.3GHz TX isolation */
+ u8 tri5gh; /* 5.8GHz TX isolation */
+ u8 rxpo2g; /* 2GHz RX power offset */
+ u8 rxpo5g; /* 5GHz RX power offset */
+ u8 rssisav2g; /* 2GHz RSSI params */
+ u8 rssismc2g;
+ u8 rssismf2g;
+ u8 bxa2g; /* 2GHz BX arch */
+ u8 rssisav5g; /* 5GHz RSSI params */
+ u8 rssismc5g;
+ u8 rssismf5g;
+ u8 bxa5g; /* 5GHz BX arch */
+ u16 cck2gpo; /* CCK power offset */
+ u32 ofdm2gpo; /* 2.4GHz OFDM power offset */
+ u32 ofdm5glpo; /* 5.2GHz OFDM power offset */
+ u32 ofdm5gpo; /* 5.3GHz OFDM power offset */
+ u32 ofdm5ghpo; /* 5.8GHz OFDM power offset */
+ u16 boardflags_lo; /* Board flags (bits 0-15) */
+ u16 boardflags_hi; /* Board flags (bits 16-31) */
+ u16 boardflags2_lo; /* Board flags (bits 32-47) */
+ u16 boardflags2_hi; /* Board flags (bits 48-63) */
+ /* TODO store board flags in a single u64 */
/* Antenna gain values for up to 4 antennas
* on each band. Values in dBm/4 (Q5.2). Negative gain means the
@@ -58,7 +88,7 @@
} ghz5; /* 5GHz band */
} antenna_gain;
- /* TODO - add any parameters needed from rev 2, 3, or 4 SPROMs */
+ /* TODO - add any parameters needed from rev 2, 3, 4, 5 or 8 SPROMs */
};
/* Information about the PCB the circuitry is soldered on. */