myri10ge: update firmware headers
Update myri10ge firmware headers to latest upstream version with
TSO6 and RSS support.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
diff --git a/drivers/net/myri10ge/myri10ge_mcp.h b/drivers/net/myri10ge/myri10ge_mcp.h
index a1d2a22..58e5717 100644
--- a/drivers/net/myri10ge/myri10ge_mcp.h
+++ b/drivers/net/myri10ge/myri10ge_mcp.h
@@ -10,7 +10,7 @@
__be32 low;
};
-/* 4 Bytes */
+/* 4 Bytes. 8 Bytes for NDIS drivers. */
struct mcp_slot {
__sum16 checksum;
__be16 length;
@@ -205,8 +205,87 @@
/* same than DMA_TEST (same args) but abort with UNALIGNED on unaligned
* chipset */
- MXGEFW_CMD_UNALIGNED_STATUS
- /* return data = boolean, true if the chipset is known to be unaligned */
+ MXGEFW_CMD_UNALIGNED_STATUS,
+ /* return data = boolean, true if the chipset is known to be unaligned */
+
+ MXGEFW_CMD_ALWAYS_USE_N_BIG_BUFFERS,
+ /* data0 = number of big buffers to use. It must be 0 or a power of 2.
+ * 0 indicates that the NIC consumes as many buffers as they are required
+ * for packet. This is the default behavior.
+ * A power of 2 number indicates that the NIC always uses the specified
+ * number of buffers for each big receive packet.
+ * It is up to the driver to ensure that this value is big enough for
+ * the NIC to be able to receive maximum-sized packets.
+ */
+
+ MXGEFW_CMD_GET_MAX_RSS_QUEUES,
+ MXGEFW_CMD_ENABLE_RSS_QUEUES,
+ /* data0 = number of slices n (0, 1, ..., n-1) to enable
+ * data1 = interrupt mode. 0=share one INTx/MSI, 1=use one MSI-X per queue.
+ * If all queues share one interrupt, the driver must have set
+ * RSS_SHARED_INTERRUPT_DMA before enabling queues.
+ */
+ MXGEFW_CMD_GET_RSS_SHARED_INTERRUPT_MASK_OFFSET,
+ MXGEFW_CMD_SET_RSS_SHARED_INTERRUPT_DMA,
+ /* data0, data1 = bus address lsw, msw */
+ MXGEFW_CMD_GET_RSS_TABLE_OFFSET,
+ /* get the offset of the indirection table */
+ MXGEFW_CMD_SET_RSS_TABLE_SIZE,
+ /* set the size of the indirection table */
+ MXGEFW_CMD_GET_RSS_KEY_OFFSET,
+ /* get the offset of the secret key */
+ MXGEFW_CMD_RSS_KEY_UPDATED,
+ /* tell nic that the secret key's been updated */
+ MXGEFW_CMD_SET_RSS_ENABLE,
+ /* data0 = enable/disable rss
+ * 0: disable rss. nic does not distribute receive packets.
+ * 1: enable rss. nic distributes receive packets among queues.
+ * data1 = hash type
+ * 1: IPV4
+ * 2: TCP_IPV4
+ * 3: IPV4 | TCP_IPV4
+ */
+
+ MXGEFW_CMD_GET_MAX_TSO6_HDR_SIZE,
+ /* Return data = the max. size of the entire headers of a IPv6 TSO packet.
+ * If the header size of a IPv6 TSO packet is larger than the specified
+ * value, then the driver must not use TSO.
+ * This size restriction only applies to IPv6 TSO.
+ * For IPv4 TSO, the maximum size of the headers is fixed, and the NIC
+ * always has enough header buffer to store maximum-sized headers.
+ */
+
+ MXGEFW_CMD_SET_TSO_MODE,
+ /* data0 = TSO mode.
+ * 0: Linux/FreeBSD style (NIC default)
+ * 1: NDIS/NetBSD style
+ */
+
+ MXGEFW_CMD_MDIO_READ,
+ /* data0 = dev_addr (PMA/PMD or PCS ...), data1 = register/addr */
+ MXGEFW_CMD_MDIO_WRITE,
+ /* data0 = dev_addr, data1 = register/addr, data2 = value */
+
+ MXGEFW_CMD_XFP_I2C_READ,
+ /* Starts to get a fresh copy of one byte or of the whole xfp i2c table, the
+ * obtained data is cached inside the xaui-xfi chip :
+ * data0 : "all" flag : 0 => get one byte, 1=> get 256 bytes,
+ * data1 : if (data0 == 0): index of byte to refresh [ not used otherwise ]
+ * The operation might take ~1ms for a single byte or ~65ms when refreshing all 256 bytes
+ * During the i2c operation, MXGEFW_CMD_XFP_I2C_READ or MXGEFW_CMD_XFP_BYTE attempts
+ * will return MXGEFW_CMD_ERROR_BUSY
+ */
+ MXGEFW_CMD_XFP_BYTE,
+ /* Return the last obtained copy of a given byte in the xfp i2c table
+ * (copy cached during the last relevant MXGEFW_CMD_XFP_I2C_READ)
+ * data0 : index of the desired table entry
+ * Return data = the byte stored at the requested index in the table
+ */
+
+ MXGEFW_CMD_GET_VPUMP_OFFSET,
+ /* Return data = NIC memory offset of mcp_vpump_public_global */
+ MXGEFW_CMD_RESET_VPUMP,
+ /* Resets the VPUMP state */
};
enum myri10ge_mcp_cmd_status {
@@ -220,7 +299,10 @@
MXGEFW_CMD_ERROR_BAD_PORT,
MXGEFW_CMD_ERROR_RESOURCES,
MXGEFW_CMD_ERROR_MULTICAST,
- MXGEFW_CMD_ERROR_UNALIGNED
+ MXGEFW_CMD_ERROR_UNALIGNED,
+ MXGEFW_CMD_ERROR_NO_MDIO,
+ MXGEFW_CMD_ERROR_XFP_FAILURE,
+ MXGEFW_CMD_ERROR_XFP_ABSENT
};
#define MXGEFW_OLD_IRQ_DATA_LEN 40