atmel-mci: add MCI2 register definitions
New revision of Atmel MCI interface adds new features. This is a update of
register definition in header file. This new MCI IP is called MCI2.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
diff --git a/drivers/mmc/host/atmel-mci-regs.h b/drivers/mmc/host/atmel-mci-regs.h
index adfb885..fc8a0fe 100644
--- a/drivers/mmc/host/atmel-mci-regs.h
+++ b/drivers/mmc/host/atmel-mci-regs.h
@@ -10,6 +10,7 @@
/*
* Superset of MCI IP registers integrated in Atmel AVR32 and AT91 Processors
+ * Registers and bitfields marked with [2] are only available in MCI2
*/
#ifndef __DRIVERS_MMC_ATMEL_MCI_H__
@@ -39,6 +40,7 @@
# define MCI_SDCSEL_MASK ( 3 << 0)
# define MCI_SDCBUS_1BIT ( 0 << 6) /* 1-bit data bus */
# define MCI_SDCBUS_4BIT ( 2 << 6) /* 4-bit data bus */
+# define MCI_SDCBUS_8BIT ( 3 << 6) /* 8-bit data bus[2] */
# define MCI_SDCBUS_MASK ( 3 << 6)
#define MCI_ARGR 0x0010 /* Command Argument */
#define MCI_CMDR 0x0014 /* Command */
@@ -67,6 +69,9 @@
#define MCI_BLKR 0x0018 /* Block */
# define MCI_BCNT(x) ((x) << 0) /* Data Block Count */
# define MCI_BLKLEN(x) ((x) << 16) /* Data Block Length */
+#define MCI_CSTOR 0x001c /* Completion Signal Timeout[2] */
+# define MCI_CSTOCYC(x) ((x) << 0) /* CST cycles */
+# define MCI_CSTOMUL(x) ((x) << 4) /* CST multiplier */
#define MCI_RSPR 0x0020 /* Response 0 */
#define MCI_RSPR1 0x0024 /* Response 1 */
#define MCI_RSPR2 0x0028 /* Response 2 */
@@ -94,7 +99,24 @@
# define MCI_DTOE ( 1 << 22) /* Data Time-Out Error */
# define MCI_OVRE ( 1 << 30) /* RX Overrun Error */
# define MCI_UNRE ( 1 << 31) /* TX Underrun Error */
+#define MCI_DMA 0x0050 /* DMA Configuration[2] */
+# define MCI_DMA_OFFSET(x) ((x) << 0) /* DMA Write Buffer Offset */
+# define MCI_DMA_CHKSIZE(x) ((x) << 4) /* DMA Channel Read and Write Chunk Size */
+# define MCI_DMAEN ( 1 << 8) /* DMA Hardware Handshaking Enable */
+#define MCI_CFG 0x0054 /* Configuration[2] */
+# define MCI_CFG_FIFOMODE_1DATA ( 1 << 0) /* MCI Internal FIFO control mode */
+# define MCI_CFG_FERRCTRL_COR ( 1 << 4) /* Flow Error flag reset control mode */
+# define MCI_CFG_HSMODE ( 1 << 8) /* High Speed Mode */
+# define MCI_CFG_LSYNC ( 1 << 12) /* Synchronize on the last block */
+#define MCI_WPMR 0x00e4 /* Write Protection Mode[2] */
+# define MCI_WP_EN ( 1 << 0) /* WP Enable */
+# define MCI_WP_KEY (0x4d4349 << 8) /* WP Key */
+#define MCI_WPSR 0x00e8 /* Write Protection Status[2] */
+# define MCI_GET_WP_VS(x) ((x) & 0x0f)
+# define MCI_GET_WP_VSRC(x) (((x) >> 8) & 0xffff)
+#define MCI_FIFO_APERTURE 0x0200 /* FIFO Aperture[2] */
+/* This is not including the FIFO Aperture on MCI2 */
#define MCI_REGS_SIZE 0x100
/* Register access macros */