i2c: designware: Fix spelling typos in the comments
Fix spelling typos in the comments with help of `codespell`.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
diff --git a/drivers/i2c/busses/i2c-designware-baytrail.c b/drivers/i2c/busses/i2c-designware-baytrail.c
index 33da07d..c6a7a00 100644
--- a/drivers/i2c/busses/i2c-designware-baytrail.c
+++ b/drivers/i2c/busses/i2c-designware-baytrail.c
@@ -1,6 +1,6 @@
// SPDX-License-Identifier: GPL-2.0
/*
- * Intel BayTrail PMIC I2C bus semaphore implementaion
+ * Intel BayTrail PMIC I2C bus semaphore implementation
* Copyright (c) 2014, Intel Corporation.
*/
#include <linux/device.h>
diff --git a/drivers/i2c/busses/i2c-designware-common.c b/drivers/i2c/busses/i2c-designware-common.c
index 72e93c1..c70c6fc 100644
--- a/drivers/i2c/busses/i2c-designware-common.c
+++ b/drivers/i2c/busses/i2c-designware-common.c
@@ -102,7 +102,7 @@ int i2c_dw_set_reg_access(struct dw_i2c_dev *dev)
i2c_dw_release_lock(dev);
if (reg == swab32(DW_IC_COMP_TYPE_VALUE)) {
- /* Configure register endianess access */
+ /* Configure register endianness access */
dev->flags |= ACCESS_SWAP;
} else if (reg == (DW_IC_COMP_TYPE_VALUE & 0x0000ffff)) {
/* Configure register access mode 16bit */
@@ -190,10 +190,10 @@ int i2c_dw_set_sda_hold(struct dw_i2c_dev *dev)
/*
* Workaround for avoiding TX arbitration lost in case I2C
- * slave pulls SDA down "too quickly" after falling egde of
+ * slave pulls SDA down "too quickly" after falling edge of
* SCL by enabling non-zero SDA RX hold. Specification says it
* extends incoming SDA low to high transition while SCL is
- * high but it apprears to help also above issue.
+ * high but it appears to help also above issue.
*/
if (!(dev->sda_hold_time & DW_IC_SDA_HOLD_RX_MASK))
dev->sda_hold_time |= 1 << DW_IC_SDA_HOLD_RX_SHIFT;
@@ -378,7 +378,7 @@ void i2c_dw_disable(struct dw_i2c_dev *dev)
/* Disable controller */
__i2c_dw_disable(dev);
- /* Disable all interupts */
+ /* Disable all interrupts */
dw_writel(dev, 0, DW_IC_INTR_MASK);
dw_readl(dev, DW_IC_CLR_INTR);
}
diff --git a/drivers/i2c/busses/i2c-designware-master.c b/drivers/i2c/busses/i2c-designware-master.c
index 05da900..3a58eef2 100644
--- a/drivers/i2c/busses/i2c-designware-master.c
+++ b/drivers/i2c/busses/i2c-designware-master.c
@@ -521,7 +521,7 @@ static u32 i2c_dw_read_clear_intrbits(struct dw_i2c_dev *dev)
/*
* The IC_INTR_STAT register just indicates "enabled" interrupts.
- * Ths unmasked raw version of interrupt status bits are available
+ * The unmasked raw version of interrupt status bits is available
* in the IC_RAW_INTR_STAT register.
*
* That is,
diff --git a/drivers/i2c/busses/i2c-designware-pcidrv.c b/drivers/i2c/busses/i2c-designware-pcidrv.c
index 050adda..656206c 100644
--- a/drivers/i2c/busses/i2c-designware-pcidrv.c
+++ b/drivers/i2c/busses/i2c-designware-pcidrv.c
@@ -109,7 +109,7 @@ static int mfld_setup(struct pci_dev *pdev, struct dw_pci_controller *c)
static int mrfld_setup(struct pci_dev *pdev, struct dw_pci_controller *c)
{
/*
- * On Intel Merrifield the user visible i2c busses are enumerated
+ * On Intel Merrifield the user visible i2c buses are enumerated
* [1..7]. So, we add 1 to shift the default range. Besides that the
* first PCI slot provides 4 functions, that's why we have to add 0 to
* the first slot and 4 to the next one.
diff --git a/drivers/i2c/busses/i2c-designware-slave.c b/drivers/i2c/busses/i2c-designware-slave.c
index 0fc3aa31d..f5ecf76 100644
--- a/drivers/i2c/busses/i2c-designware-slave.c
+++ b/drivers/i2c/busses/i2c-designware-slave.c
@@ -107,7 +107,7 @@ static u32 i2c_dw_read_clear_intrbits_slave(struct dw_i2c_dev *dev)
/*
* The IC_INTR_STAT register just indicates "enabled" interrupts.
- * Ths unmasked raw version of interrupt status bits are available
+ * The unmasked raw version of interrupt status bits is available
* in the IC_RAW_INTR_STAT register.
*
* That is,